35 5000 Print Controller Guide
-
Upload
eduardo-b-velasco -
Category
Documents
-
view
220 -
download
0
Transcript of 35 5000 Print Controller Guide
-
7/28/2019 35 5000 Print Controller Guide
1/108
MuratecPrinter Controller
TWAIN Driver
Operating instructions
forMFX-1600
MFX-1200
F-360
F-320
-
7/28/2019 35 5000 Print Controller Guide
2/108
Software License Agreement
READ BEFORE INSTALLATION
This Software License Agreement (hereinafter the Agreement) is a legal contract
made between you (regardless of an individual or a legal entity) and Murata
Machinery, Ltd. (hereinafter Murata) regarding the Murata software products
contained in the CD-ROM (hereinafter the Software).
Please read the following terms carefully before installing the Software.
You can install and use the Software subject to your knowledge and acceptance of
all of the following terms. If you do not agree to any of the following terms, you
should cancel the installing process.
The condition of the software license:
1. Any and all copyright and any other intellectual property regarding the
Software remain solely the property of Destiny Technology Corporation(hereinafter Destiny) and Murata.
2. You may use the Software only in the country of your purchase and only for the
purpose of using the hardware of Murata and other companies approved by
Murata (hereinafter OEM Companies).
3. You may use the Software only in compliance with notices and restrictions
written in this manual.
4. You must not modify, alter all or any part of the Software. You must not make
any attempt to discover the source code of the Software by any method
including reverse-engineering, de-compiling, or de-assembling.
5. You must not sell, transfer, rent, lease or sublicense the Software to any third
party by transmitting the software via phone-line or network, or by copying the
software to floppy disk, CD-ROM, magnetic data tape or any other media.
6. The software is subject to changes by Murata or Destiny in its specifications
and program without any prior notice.
7. Before installing the software, you are supposed to take any and all procedures
necessary to secure your records and data at your cost and responsibility,
including making backup of your computer files.
Neither Murata, Destiny, OEM Companies nor their distributors/sub-distribu-
tors shall be liable for any damage or loss caused by your failure of taking the
foregoing procedure.
8. Neither Murata, Destiny, OEM Companies nor their distributors/sub-distribu-
tors shall be liable for any damage or loss caused by (1) use of the software in
combination with the hardware other than the hardware which is defined in
Section 2 above or (2) modification of the software.
9. Neither Murata, Destiny, OEM Companies nor their distributors/sub-distribu-
tors shall assume any damages incurred by you or a third party even if suchdamage is directly/indirectly caused by use of the software or incapability to
use the software.
-
7/28/2019 35 5000 Print Controller Guide
3/108
Trademark and Copyrights Muratec, the Muratec logo and all Muratec fax product names contained herein are
trademarks of Murata machinery, Ltd. and Muratec UK, Ltd.
Destiny is a registered trademark of Destiny Technology Corporation.
LaserAct is a registered trademark of Destiny Technology Corporation.
DPOS is a registered trademark of Destiny Technology Corporation.
WinPanel is a registered trademark of Destiny Technology Corporation.
LaserAct Copyrights1992-1999, Destiny Technology Corporation, Ver.2.0
All Right Reserved.
WinRefs Copyrights1995-1999, Destiny Technology Corporation, Ver.2.0
All Right Reserved.
WinPanel Copyrights1995-1999, Destiny Technology Corporation, Ver.1.0All Right Reserved.
i486, i486DX and Pentium are either registered trademarks or trademarks ofIntel Corporation.
covered by one or more of the following US Patents:5,029,108:5,396,584; and by
patents in other countries.
Agfa and Agfa Rhombus are registered trademarks of Agfa-Gevaert N.V.
Universal Font Scaling Technology (UFST) is a trademark of Agfa
Corporation.
PCL is a registered trademark of Hewlett Packard Company.
Centronics is a registered trademark of GENICOM Corporation.
Microsoft, Windows, Windows 3.1, Windows 95, Windows 98 and Windows
NT are registered trademarks of Microsoft Corporation.
Screen shots reprinted by permission from Microsoft Corporation.
i
-
7/28/2019 35 5000 Print Controller Guide
4/108
Table of contents
Introductions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v
How to use this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v
If problems arise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi
Installing the Printer control board . . . . . . . . . . . . . . . . . . . . . . . .vi
Connect the Muratec machine to your computer . . . . . . . . . . . . . .vi
Chapter 1
Using the Muratec machine as a PC printer
System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.1
Doc. Pilot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.1
Remote Shuttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.1
ONLINE key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.2Installation for Windows 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . .1.3
Installation for Windows 95/98/Me . . . . . . . . . . . . . . . . . . . . . . .1.5
Installation for Windows NT 4.0 . . . . . . . . . . . . . . . . . . . . . . . . .1.7
Installation for Windows 3.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.9
Using the Remote Shuttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.11
About Remote Shuttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.11
Setting up the printer using the Remote Shuttle . . . . . . . . . . .1.12
Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.13
For MFX-1600 and MFX-1200 . . . . . . . . . . . . . . . . . . . . . . . . .1.13
Error Message For F-320 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.18
Error Message For F-320 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.19
Cancelling the printing job . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.28
For MFX-1600 and MFX-1200 . . . . . . . . . . . . . . . . . . . . . . . . .1.28
For F-320 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.28
For F-360 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.29
Using your machine on a Network . . . . . . . . . . . . . . . . . . . . . . .1.30
Connection through print server PC . . . . . . . . . . . . . . . . . . . .1.30Connecting through optional network interface . . . . . . . . . . . .1.31
Peer to peer network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.31
Client/Server network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.31
EtherNet connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.32
Entering the IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.32
Installing the software for your network environment . . . . . .1.32
To remove the software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.35
Set TCP/IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.36
For MFX-1600 and 1200: . . . . . . . . . . . . . . . . . . . . . . . . . .1.36For F-320: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.37
For F-360: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.38
ii
-
7/28/2019 35 5000 Print Controller Guide
5/108
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.39
Print the Demo Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.39
Print the Printer Configuration Page . . . . . . . . . . . . . . . . . . . .1.39
Print PCL Font List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.40
Print NIC status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.41
Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.42AGFA Font Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.43
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.44
Chapter 2
Using the Muratec machine as a scanner
System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.2
To install the TWAIN driver . . . . . . . . . . . . . . . . . . . . . . . . . . .2.2
To uninstall the TWAIN driver . . . . . . . . . . . . . . . . . . . . . . . . .2.2
Getting ready to use the Muratec TWAIN driver . . . . . . . . . . . . .2.3
For your information in using the Muratec TWAIN driver . . . .2.3
Scanning the image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.5
Access to the Muratec TWAIN driver . . . . . . . . . . . . . . . . . . . . . .2.5
Using the RS mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.6
Scanning with RS mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.6
Using the SB mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.9
The basic operation for the SB mode . . . . . . . . . . . . . . . . . .2.9Register or modify a scan box . . . . . . . . . . . . . . . . . . . . . . .2.10
Scanning the image into a scan box . . . . . . . . . . . . . . . . . .2.16
Erasing a document stored in a scan box . . . . . . . . . . . . . .2.21
Erasing an empty scan box . . . . . . . . . . . . . . . . . . . . . . . . .2.26
Printing a list of documents stored in the scan boxes . . . . .2.29
Retrieving an image from the scan box . . . . . . . . . . . . . . . .2.30
Changing the initial settings . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.33
Scan parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.33
Scanner auto reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.37Printing a list of scanner settings . . . . . . . . . . . . . . . . . . . .2.39
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.40
Entering characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.40
The list of scanner settings . . . . . . . . . . . . . . . . . . . . . . . . . . .2.44
Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.45
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.49
iii
-
7/28/2019 35 5000 Print Controller Guide
6/108
IntroductionsThank you for purchasing the Muratec OP-150. It contains printer driverand TWAIN driver for upgrading the Muratec machine.
The Muratec printer driver allows you to use the Muratec machine as a
PC printer. And the Muratec TWAIN driver allows you to use theMuratec machine as a scanner. The Muratec TWAIN driver is the inter-face between your software and your Muratec machine. It has twoscanning modes, RS mode and SB mode, that are described in chapter 2.
How to use this manual
This manual contains information you need to install and use theMuratec printer driver and Muratec TWAIN driver with your Muratecmachine.
Chapter 1 describes installing the Muratec printer driver and using theMuratec printer driver utilities, Remote Shuttle and Doc. Pilot.
Chapter 2 describes installing the Muratec TWAIN driver and how touse it with Muratec machine.
If problems arise
In the event repairs are ever needed on your fax machine, contact anauthorised representative of Muratec.
iv
-
7/28/2019 35 5000 Print Controller Guide
7/108
Unpacking
Heres what should be in the OP-150 package:
Be sure to save the packing materials for reshipment.
Installing the Printer control board
Your authorized Muratec dealer should install the OP-150 printer con-
troller to your machine. Do not perform this installation yourself.
Connect the Muratec machine to your computer
1 Turn off both your Muratec machine and computer.
2 Connect the Muratec machine to your computer using thebi-directional parallel interface cable.
3 Turn on the Muratec machine and your computer.Important: If the Windows Plug & Play screen appears when youstart your Windows, DO NOT use this function.Please install the Muratec driver following to the
instructions beginning page 1.3 or 2.2.
Printer controller board
Screw
Connection cable A
Connection cable B
Connection cable C
Ferrite core
Operating instructions Muratec OP-150 CD-ROM
Connection board 1 Connection board 2
v
-
7/28/2019 35 5000 Print Controller Guide
8/108
This page intentionally blank.
vi
-
7/28/2019 35 5000 Print Controller Guide
9/108
Chapter 1
Using the Muratec machineas a PC printer
-
7/28/2019 35 5000 Print Controller Guide
10/108
-
7/28/2019 35 5000 Print Controller Guide
11/108
System requirements
The following are the minimum computer requirements to install andoperate the Doc. Pilot and Remote Shuttle.
CPU: i486DX/66MHz or higher
Operating System: Windows95, Windows98, WindowsMe,WindowsNT 4.0 or Windows2000
Hard Disk Drive: At least 10MB of available disk space for installing
RAM: At least 8 MB
Terminal Connector Interface: A bidirectional parallel interfaceIEEE1284 (Compatible mode / Nibblemode / ECP mode)
You will also need a bi-directional parallel interface cable (printer cable)
to connect your Muratec machine to your PC.Note:Actual requirements will vary based on your PC system configura-
tion, the applications and the document you will print.
Doc. Pilot
The Doc. pilot is a PCL printer driver that enables your software applica-tions to access your Muratec machines printer features.
The Muratec OP-150 includes the following printer drivers:
Use the PCL 6 driver to take full advantage of the printer features.The PCL 6 driver is recommended unless backward compatibility with
previous PCL drivers or older printers is necessary.
Use the PCL 5e driver if you want to preserve compatibility with older
software applications.
Remote Shuttle
The Muratec OP-150 also includes a Remote Shuttle for Doc Pilot printersoftware for end-users.
Remote Shuttle shows the status of your printer and can show and set thedefault value of the printer parameters. With it, you can check the printerstatus and set printer parameters from your PC easily and quickly.
1.1
-
7/28/2019 35 5000 Print Controller Guide
12/108
ONLINE key
When the OP-150 has been installed to Muratec F-360 or F-320, the Softkey which is assigned toMemory transmission on/offwill be changed tothe ONLINE key for OP-150.
The ONLINE key is used for the cancelling of PC printing. (See pages1.281.29.)
O N L I N E k e y
1.2
-
7/28/2019 35 5000 Print Controller Guide
13/108
Installation for Windows 2000
Important: To install or uninstall the software using the Windows
2000, you must be logged in as the Administrator.
Important: Before you install the software, you must read theREADME. TXT file in the appropriate directory of the
CD-ROM for important last-minute installation information
and helpful hints:
X:\Printer\XXXXX\Win2000\Setup\README.TXT
(X is the drive letter for your CD-ROM drive.
In XXXXX, your Muratec machines model name will beapplied.)
To install the Doc. Pilotand Remote ShuttleYou can use the software installation program that is provided on theCD-ROM to install both theDoc. Pilot and theRemote Shuttle at the sametime.
1 Start Windows.
2 Insert the Muratec OP-150 CD-ROM into your CD-ROM drive.
3 Click Start, then select Run.
4 Type X:\Printer\XXXXX\Win2000\Setup\Setup.exeNote: X is the drive letter for your CD-ROM drive. In XXXXX,
type your Muratec machines model name such as F360.
You can also browse through the folders to find the Setup.exe
file for your version of Windows by clicking Browse button.
5 Click OKto start the software installation program.
6 Follow the instructions that appear on the screen.
Note:According to the version of the printer driver, when you areinstalling it in Windows 2000, the Digital Signature Not
Found display may appear on your screen. However, if there
is no problem functionally, click Yes and you can continuethe installation.
7 After you install the Doc. Pilot and restart your computer, theicon for the Doc Pilot appears in the Printers folder, if youveinstalled the Remote Shuttle, the Remote Shuttle button appears
on the task bar.
1.3
-
7/28/2019 35 5000 Print Controller Guide
14/108
To remove the Doc. Pilot and Remote Shuttle
1 Close the Remote Shuttle, if it is running.
2 To start the Doc Pilot uninstaller program, click onStart>Programs>Doc Pilot, then click
Doc Pilot XXXXX Uninstaller. (XXXXX means the model nameof your Muratec machine, such as F360.)
3 Follow the instructions that appear on the screen.
Setting up the printer with the PCL driver
You can access the PCL driver through the printer setup command pro-vided by most software applications, or you can use the following
procedure to access it using the Windows
printers window.
1 Click on Start > Settings, then click on Printers.
2 Click this icon, and select Printing Preference from the Filemenu. You will see the following display or one similar.
Now you can access the various windows of the driver by selecting the
tabs at the top of the screen. For details on how to use the settings andbuttons, see on-line help by using the Help button.
1.4
-
7/28/2019 35 5000 Print Controller Guide
15/108
Installation for Windows 95/98/Me
Important: Before you install the software, you must read the
README. TXT file in the appropriate directory of the
CD-ROM for important last-minute installation informationand helpful hints:
X:\Printer\XXXXX\Win9x_Me\Setup\README.TXT
(X is the drive letter for your CD-ROM drive.
In XXXXX, your Muratec machines model name will be
applied.)
To install the Doc. Pilotand Remote Shuttle
You can use the software installation program that is provided on the
CD-ROM to install both the Doc. Pilot and theRemote Shuttle at the sametime.
1 Start Windows.
2 Insert the Muratec OP-150 CD-ROM into your CD-ROM drive.
3 Click Start, then select Run.
4 Type X:\Printer\XXXXX\Win9x_Me\Setup\Setup.exeNote: X is the drive letter for your CD-ROM drive. In XXXXX,
type your Muratec machines model name such as F360.
You can also browse through the folders to find the Setup.exe
file for your version of Windows by clicking Browse button.
5 Click OKto start the software installation program.
6 Follow the instructions that appear on the screen.
7 After you install the Doc. Pilot and restart your computer, theicon for the Doc Pilot appears in the Printers folder, if youve
installed the Remote Shuttle, the Remote Shuttle button appearson the task bar.
1.5
-
7/28/2019 35 5000 Print Controller Guide
16/108
To remove the Doc. Pilot and Remote Shuttle utility
1 Close the Remote Shuttle, if it is running.
2 To start the Doc Pilot uninstaller program, click onStart>Programs>Doc Pilot, then click
Doc Pilot XXXXX Uninstaller. (XXXXX means the model nameof your Muratec machine, such as F360.)
3 Follow the instructions that appear on the screen.
Setting up the printer with the PCL driver
You can access the PCL driver through the printer setup command pro-vided by most software applications, or you can use the following
procedure to access it using the Windows
printers window.
1 Click on Start > Settings, then click on Printers.
2 Click this icon, and select Properties from the File menu. You willsee the following display or one similar.
Now you can access the various windows of the driver by selecting the
tabs at the top of the screen. For details on how to use the settings andbuttons, see on-line help by using the Help button.
1.6
-
7/28/2019 35 5000 Print Controller Guide
17/108
Installation for Windows NT 4.0
Important: To install or uninstall the software using the Windows NT
Version 4.0, you must be logged in as the Administrator.
Important: Before you install the software, you must read theREADME. TXT file in the appropriate directory of the
CD-ROM for important last-minute installation information
and helpful hints.
X:\Printer\XXXXX\WinNT4\Setup\README.TXT
(X is the drive letter for your CD-ROM drive.
In XXXXX, your Muratec machines model name will beapplied.)
To install the Doc. Pilotand Remote ShuttleYou can use the software installation program that is provided on theCD-ROM to install both theDoc. Pilot and theRemote Shuttle at the sametime.
1 Start Windows.
2 Insert the Muratec OP-150 CD-ROM into your CD-ROM drive.
3 Click Start, then select Run.
4 Type X:\Printer\XXXXX\WinNT4\Setup\Setup.exeNote: X is the drive letter for your CD-ROM drive. In XXXXX,
type your Muratec machines model name such as F360.
You can also browse through the folders to find the Setup.exe
file for your version of Windows by clicking Browse button.
5 Click OKto start the software installation program.
6 Follow the instructions that appear on the screen.
7 After you install the Doc. Pilot and restart your computer, theicon for the Doc Pilot appears in the Printers folder, if youve
installed the Remote Shuttle, the Remote Shuttle button appears
on the task bar.
1.7
-
7/28/2019 35 5000 Print Controller Guide
18/108
To remove the Doc. Pilot and Remote Shuttle utility
1 Close the Remote Shuttle, if it is running.
2 To start the Doc Pilot uninstaller program, click onStart>Programs>Doc Pilot, then click
Doc Pilot XXXXX Uninstaller. (XXXXX means the model nameof your Muratec machine, such as F360.)
3 Follow the instructions that appear on the screen.
Setting up the printer with the PCL driver
You can access the PCL driver through the printer setup command pro-vided by most software applications, or you can use the following
procedure to access it using the Windows
printers window.
1 Click on Start > Settings, then click on Printers.
2 Click this icon, and select Document Defaults from the Filemenu. You will see the following display or one similar.
Now you can access the various windows of the driver by selecting thetabs at the top of the screen. For details on how to use the settings andbuttons, see on-line help by using the Help button.
1.8
-
7/28/2019 35 5000 Print Controller Guide
19/108
Installation for Windows 3.1
Important: Before you install the software, you must read the
README. TXT file in the appropriate directory of the
CD-ROM for important last-minute installation informationand helpful hints.
X:\Printer\MFX12_16\Win3x\Setup\README.TXT
(X is the drive letter for your CD-ROM drive.
Note:OP-150 for F-360 and F-320 is not support the Windows 3.1.
To install the Doc. Pilotand Remote Shuttle
You can use the software installation program that is provided on theCD-ROM to install both theDoc. Pilot and theRemote Shuttle at the same
time.
1 Start Windows.
2 Insert the Muratec OP-150 CD-ROM into your CD-ROM drive.
3 Click the File menu in the Program Manager, then click Run.
4 Type X:\Printer\MFX12_16\Win3x\Setup\Setup.exeNote: X is the drive letter for your CD-ROM drive.
You can also browse through the folders to find the Setup.exefile for your version of Windows by clicking the Browse
button.
5 Click OKto start the software installation program.
6 Follow the instructions that appear on the screen.
To remove the Doc. Pilot and Remote Shuttle utility
1 Close the Remote Shuttle, if it is running.
2 To start the Doc Pilot uninstaller program, open the Doc Pilotwindow in Program Manager.
Double-click the Doc Pilot MFX12_16 Uninstaller icon in the Doc
Pilot window.
3 Follow the instructions that appear on the screen.
1.9
-
7/28/2019 35 5000 Print Controller Guide
20/108
Setting up the printer with the PCL driver
You can access the PCL driver through the printer setup command pro-vided by most software applications, or you can use the followingprocedure to access it using the Windows Control Panel.
1 In the Program Manager Main group, double-click the ControlPanel icon.
2 Double-click the Printers icon.
3 In the Installed Printers box, make sure that the printer is selectedas default printer, and then click the Setup... button.You will see the following display or one similar.
Now you can access the various windows of the driver by selecting thetabs at the top of the screen. For details on how to use the settings andbuttons, see on-line help by using the Help button.
1.10
-
7/28/2019 35 5000 Print Controller Guide
21/108
Using the Remote Shuttle
About Remote Shuttle
Remote Shuttle is the software utility that monitors the printer status.
It helps you quickly determine the cause of problems and tells you whatyou need to do to correct them.
Also, you can set the printer settings from your PC using the RemoteShuttle. (See next page.)
The following is an example of a screen produced by Remote Shuttle.
Reduced view:
Enlarged view:
Note:The Remote Shuttle does not work in a network environment.It works only for the printer directly connected to your PC with bi-
directional parallel cable.
1.11
-
7/28/2019 35 5000 Print Controller Guide
22/108
Setting up the printer using the Remote Shuttle
1 Click Printer Settingfrom the Setup menu on the reduced viewscreen, or click the Printer Settingbutton on the enlarged viewscreen of the Remote Shuttle.
You will see the following display or one similar.
Now you can access the various windows of the driver by selecting thetabs at the top of the screen. For details on how to use the settings andbuttons, see on-line help by using the Help button.
Note:The Net Settingappearing on the screen is available only when
the optional network interface card is attached to your machine.
1.12
-
7/28/2019 35 5000 Print Controller Guide
23/108
Error MessagesThe following message is displayed on the LCD of the printer.
If your machine is an MFX-1600 or MFX-1200, see below.
If your machine is an F-320, see page 1.19.
If your machine is an F-360, see page 1.23.
For MFX-1600 and MFX-1200
Message Meaning
Paper Mismatch Cassette paper size does not match the paper size
Start/Stop/CopyReset specified in the application.
Change the paper in paper cassette or paper
source.
If you press STOP, the printer will cancel the
current printing job.
If you press COPY RESET, the printer will cancel
all printing jobs stored in its memory.
(See Paper Mismatch error,page 1.15.)
Drawer Size Error The paper size you specified cannot be set in the
Start/Stop/CopyReset paper cassette.
Use the bypass tray. To select the bypass tray,
press START then select Tray by pressing
PAPER SIZE?. Set the specified paper in bypass
tray.
If you press STOP, the printer will cancel the
current printing job.
If you press COPY RESET, the printer will cancel
all printing jobs stored in memory.
(See Drawer Size Error,page 1.16.)
Memory Overflow The printer received more data from the
Start/Stop/CopyReset computer than it can fit in memory.
Press START to continue, but there may be some
data loss.If you press STOP, the printer will cancel the
current printing job.
If you press COPY RESET, the printer will cancel
all printing jobs stored in memory.
Print Overrun Data sent to the printer is too complex.
Start/Stop/CopyReset Press START to continue, but there may be some
data loss.
If press STOP, the printer will cancel the current
printing job.If you press COPY RESET, the printer will cancel
all printing jobs stored in memory.
1.13
-
7/28/2019 35 5000 Print Controller Guide
24/108
For MFX-1600 and MFX-1200
Message Meaning
Unable To Sort The data is too large to sort.
Start/Stop/CopyReset If you press START, the printer will print only
the document stored in its memory withoutsorting.
If you press STOP, the printer will cancel the
current printing job.
If you press COPY RESET, the printer will cancel
all printing jobs stored in its memory.
Option Install Error The optional paper cassette or 2-Bin tray are not
Start/Stop/CopyReset installed.
Press START. The printer will print your docu-ment.
Press START then select correct paper source by
pressing PAPER SIZE. And then press START
again to resume printing.
If you press STOP, the printer will cancel the
current printing job.
If you press COPY RESET, the printer will cancel
all printing jobs stored in its memory.
(See Option Install Error,page 1.17.)
Please Supply Paper The printer has run out of paper.
Stop/CopyReset Add the appropriate type of paper.
If you press STOP, the printer will cancel the
current printing job.
If you press COPY RESET, the printer will cancel
all printing jobs stored in memory.
Please Replace Drum The drum cartridge has reached the limit of its
Stop/CopyReset design life.Replace the drum cartridge.
If you press STOP, the printer will cancel the
current printing job.
If you press COPY RESET, the printer will cancel
all printing jobs stored in its memory.
Please Replace Toner Your toner cartridge is empty.
Stop/CopyReset Replace the toner cartridge.
If you press STOP, the printer will cancel the
current printing job.If you press COPY RESET, the printer will cancel
all printing jobs stored in memory.
1.14
-
7/28/2019 35 5000 Print Controller Guide
25/108
For MFX-1600 and MFX-1200
Message Meaning
Close 1st Cassette Paper cassette is open.
Stop/CopyReset Close it.
If you press STOP, the printer will cancel thecurrent printing job.
If you press COPY RESET, the printer will cancel
all printing jobs stored in memory.
PCL: System Error XX An internal controller error has occurred.
Turn the printer off then back on. If the error
appears again, contact your authorized Muratec
dealer or Muratec Customer Support.
Paper Mismatch error
If the size of paper in paper cassette does not match the paper size specifiedin the application, the following message will appear on the printers LCD:
To resume the printing:
1 Press START.
Paper size of the selected paper cassette.
Specified paper size
2 Change the paper in the paper cassette you selected (if necessary,see your fax machines operating instructions). Then pressPROGRAM
and select the same sized paper using the cursor key.After you change the paper, press ENTER. The printer will resume
the printing automatically.orIf another paper source (e.g. 2nd cassette) has the correct sized
paper for the print job, press PAPER SIZE key to select it. Then pressSTART to resume printing.
To cancel printing job:
If you want to cancel the current printing job, press STOP.
If you want to cancel all printing jobs stored in memory, press COPY RESET.
Select Paper SourceA4 A5
Paper MismatchStart/Stop/CopyReset
1.15
-
7/28/2019 35 5000 Print Controller Guide
26/108
Drawer Size error
If the paper you select is not acceptable for the paper cassette (seePaper, page 1.42), the following message will appear on the printers LCD:
To resume the printing:
1 Press START.
Paper size of the selected paper cassette.Specified paper size
2 Press PAPER SIZE to select the bypass tray.
3 Set the paper in bypass tray and set thepaper size (if necessary, see your machines operating instructions).
Then press START to resume printing.
To cancel this printing job:
If you want to cancel the current printing job, press STOP.
If you want to cancel all printing jobs stored in memory, press COPY RESET.
Select Paper SourcePost None
Select Paper SourcePost A4
Drawer Size ErrorStart/Stop/CopyReset
1.16
-
7/28/2019 35 5000 Print Controller Guide
27/108
Option Install error
If you tried to print with the optional 2nd paper cassette or 2-Bin traywhen they are not installed, the following message will appear on theprinters LCD:
To resume the printing:
1 Press START. The printer will resume printing.
1 Press START.
2 Press PAPER SIZE to select the 1st papercassette or bypass tray.
If you select the 1st paper cassette, you
can change the paper size by followingprocedures:
While you select the 1st paper cassette, press PROGRAM then selectthe paper size using the cursor key and then press ENTER.
3 Press START to resume the printing.
To cancel this printing job:
If you want to cancel the current printing job, press STOP.
If you want to cancel the all printing jobs, press COPY RESET.
Select Paper SourceA4 A4
Option Install ErrorStart/Stop/CopyReset
1.17
-
7/28/2019 35 5000 Print Controller Guide
28/108
Error Message For F-320
Message Meaning
Paper Mismatch Cassette paper size does not match the paper size
Start/Stop specified in the application.
Change the paper in paper cassette or papersource.
If you press STOP, the printer will cancel the
current printing job.
(See Paper Mismatch Error,page 1.20.)
Drawer Size Error The paper size you specified cannot be set in the
Start/Stop paper cassette.
Use the bypass tray. To select the bypass tray,
press START, then select Tray using or .
Set the specified paper in bypass tray.If you press STOP, the printer will cancel the
current printing job.
(See Drawer Size Error,page 1.21.)
Memory Overflow The printer received more data from the
Start/Stop computer than it can fit in memory.
Press START to continue, but there may be some
data loss.
If you press STOP, the printer will cancel the
current printing job.
Print Overrun Data sent to the printer is too complex.
Start/Stop Press START to continue, but there may be some
data loss.
If press STOP, the printer will cancel the current
printing job.
Unable to Sort The data is too large to sort.
Start/Stop If you press START, the printer will print only
the document stored in its memory withoutsorting.
If you press STOP, the printer will cancel the
current printing job.
1.18
-
7/28/2019 35 5000 Print Controller Guide
29/108
Error Message For F-320
Message Meaning
Option Install Error The optional paper cassette or 2-Bin tray are not
Start/Stop installed.
Press START. The printer will print your docu-
ment.
Press START then select correct paper source
using or . And then press START again toresume printing.
If you press STOP, the printer will cancel the
current printing job.
(See Option Install Error,page 1.22.)Please Supply Paper The printer has run out of paper.
Stop Add the appropriate type of paper.
If you press STOP, the printer will cancel the
current printing job.
Please Replace Drum The drum cartridge has reached the limit of its
Stop design life.
Replace the drum cartridge.
If you press STOP, the printer will cancel the
current printing job.
Please Replace Toner Your toner cartridge is empty.
Stop Replace the toner cartridge.
If you press STOP, the printer will cancel the
current printing job.
Close 1st Cassette Paper cassette is open.
Stop Close it.
If you press STOP, the printer will cancel the
current printing job.PCL: System Error XX An internal controller error has occurred.
Turn the printer off then back on. If the error
appears again, contact your authorized Muratec
dealer or Muratec Customer Support.
1.19
-
7/28/2019 35 5000 Print Controller Guide
30/108
Paper Mismatch error
If the size of paper in paper cassette does not match the paper size speci-fied in the application, the following message will appear on the printersLCD:
To start the printing:
1 Press START.
Paper size of the selected paper cassette.
Specified paper size
C1 means the 1st paper cassette.C2 means the 2nd paper cassette.
Tray means the bypass tray.
2 Change the paper in the paper cassette you selected (if necessary,see your fax machines operating instructions). Then press MENU
and select the same sized paper using the cursor key. After you
change the paper, press ENTER. Your machine will start the printingautomatically.
orIf another paper source (e.g. 2nd cassette) has the correct sized
paper for the print job, press or to select it. Then press START
to start printing.
To cancel printing job:
If you want to cancel the current printing job, press STOP.
Select Paper SourceA4 ! A5 :C1 !
Paper MismatchStart/Stop
1.20
-
7/28/2019 35 5000 Print Controller Guide
31/108
Drawer Size error
If the paper you select is not acceptable for the paper cassette (seePaper, page 1.42), the following message will appear on the printers LCD:
To start the printing:
1 Press START.
Paper size of the selected paper cassette.Specified paper size
C1 means the 1st paper cassette.
C2 means the 2nd paper cassette.
Tray means the bypass tray.
2 Press or to select the bypass tray.
3 Set the specified paper in bypass tray and set the paper size (if nec-essary, see your fax machines operating instructions). Then pressSTART to start printing.
To cancel this printing job:
If you want to cancel the current printing job, press STOP.
Select Paper SourcePost !None:Tray !
Select Paper SourcePost ! A4 :C1 !
Drawer Size ErrorStart/Stop
1.21
-
7/28/2019 35 5000 Print Controller Guide
32/108
Option Install error
If you tried to print with the optional 2nd paper cassette or 2-Bin traywhen they are not installed, the following message will appear on theprinters LCD:
To start the printing:
1 Press START. The printer will resume printing.
1 Press START.
Paper size of the selected paper cassette.
Specified paper size
C1 means the 1st paper cassette.Tray means the bypass tray.
2 Press or to select the 1st paper cassette or bypass tray.
If necessary, you can change the paper size setting by following
procedures
Press MENU then select the paper size using the cursor key andthen press ENTER.
3 Press START to resume the printing.
To cancel this printing job:
If you want to cancel the current printing job, press STOP.
Select Paper SourceA4 ! A4 :C1 !
Option Install ErrorStart/Stop
1.22
-
7/28/2019 35 5000 Print Controller Guide
33/108
Error message For F-360
Message Meaning
Paper Mismatch Cassette paper size does not match the specified
Change Paper Size: paper size displayed on the LCD.
xxxxx Change the paper in paper cassette or select[ Cancel ] [ Start ] paper source.
(See Paper Mismatch error,page 1.25.)
Draw Size Error The paper size you specified cannot be set in the
Change Paper Size: paper cassette.
xxxxx Use the bypass tray.
[ Cancel ] [ Start ] (See Drawer Size Error, page 1.26.)
Memory Overflow The printer received more data from the computer
Print Spooled Data? than it can fit in memory.Press [Start] to continue, but there may be
[ Cancel ] [ Start ] some data loss.
If you press [Cancel], the printer will cancel the
current printing job.
Print Overrun Data sent to the printer is too complex.
Print Spooled Data? Press [Start] to continue, but there may be
some data loss.
[ Cancel ] [ Start ] If you press [Cancel], the printer will cancel the
current printing job.Unable to Sort The printing data is too large to sort.
Print Spooled Data? If you press [Start], the printer will print only
the document stored in its memory without
[ Cancel ] [ Start ] sorting.
If you press [Cancel], the printer will cancel the
current printing job.
Option Install Error The optional paper cassette or 2-Bin tray are not
No Option is Detected: installed.
xxxxx (See Option Install Error, page 1.27.)[ Cancel ] [ Start ]
Paper Empty The printer has run out of paper.
Supply Paper: Add the appropriate type of paper.
xxxxx If you press [Cancel], the printer will cancel the
[ Cancel ] current printing job.
1.23
-
7/28/2019 35 5000 Print Controller Guide
34/108
For F-360
Message Meaning
Drum End The drum cartridge has reached the limit of its
Please Replace Drum design life.
Replace the drum cartridge.[ Cancel ] If you press [Cancel], the printer will cancel the
current printing job.
Toner Empty Your toner cartridge is empty.
Please Replace Toner Replace the toner cartridge.
If you press [Cancel], the printer will cancel the
[ Cancel ] current printing job.
Cassette Open Paper cassette indicated on the LCD is open.
Close xxx Cassette Close it.
If you press [Cancel], the printer will cancel the
[ Cancel ] [ Start ] current printing job.
PCL: System ErrorXX An internal controller error has occurred.
Turn the printer off then back on. If the error
appears again, contact your authorized Muratec
dealer or Muratec Customer Support.
1.24
-
7/28/2019 35 5000 Print Controller Guide
35/108
Paper Mismatch error
If the size of paper in paper cassette does not match the paper size speci-fied in the application, the following message will appear on the LCD:
Ex.)
To start the printing job:
1 Press [Start].
2 If another paper source (e.g. 2nd cassette) has the correct sizedpaper for this print job, select it using the cursor key.
Then press [Start] to resume printing.orChange the paper in the paper cassette you selected (if necessary,
see your fax machines operating instructions). Then press [Paper]
and select the same sized paper using the cursor key and thenpress ENTER. Then press [Start] to start the printing.
orPress [Start] without any changes to forced start the print-ing.
To cancel printing job:
1 If you want to cancel the current printing job, press [Cancel].
2 If you sure to cancel, press [Yes]. Otherwise, press [No].
O K t o C a n c e l ?
C u r r e n t P r i n t i n g J o b C a n c e l
[ Y e s ] [ N o ]
P a p e r M i s m a t c h
A 5
C h a n g e P a p e r S i z e :
[ C a n c e l ] [ S t a r t ]
P a p e r M i s m a t c h
S e l e c t S o u r c e /
A 4 < - - A 5
[ P a p e r ] [ S t a r t ]
P a p e r M i s m a t c h
A 5
C h a n g e P a p e r S i z e :
[ C a n c e l ] [ S t a r t ]
P a p e r M i s m a t c h
1.25
Specified paper size.
Paper size in the selected paper source.
-
7/28/2019 35 5000 Print Controller Guide
36/108
Drawer Size error
If the paper you select is not acceptable for the paper cassette (seePaper, page 1.42), the following message will appear on your F-360s LCD:
To start the printing job:
1 Press [Start].
2 Use the cursor key to select the Bypass tray.
3 Set the specified paper in bypass tray (if necessary, see your faxmachines operating instructions), then press [Paper]. Select the
same sized paper using the cursor key and then press ENTER.
Then press [Start] to start the printing.
To cancel this printing job:
1 If you want to cancel the current printing job, press [Cancel].
2 If you sure to cancel, press [Yes]. Otherwise, press [No].
O K t o C a n c e l ?
C u r r e n t P r i n t i n g J o b C a n c e l
[ Y e s ] [ N o ]
D r a w S i z e E r r o r
B y p a s s T r a y
M o n a r c h
P o s t c a r d
C u s t o m
S e l e c t S o u r c e /
A 4 < - - M o n a r c h
[ P a p e r ] [ S t a r t ]
D r a w S i z e E r r o r
S e l e c t S o u r c e /
A 4 < - - M o n a r c h
[ P a p e r ] [ S t a r t ]
D r a w S i z e E r r o r
M o n a r c h
C h a n g e P a p e r S i z e :
[ C a n c e l ] [ S t a r t ]
D r a w S i z e E r r o r
1.26
Specified paper size.
Paper size in the selected paper source.
-
7/28/2019 35 5000 Print Controller Guide
37/108
Option Install error
If you tried to print with the optional 2nd paper cassette or 2-Bin traywhen they are not installed, the following message will appear on yourF-360s LCD:
To start the printing job:
1 Press [Start]. The printer will resume printing.
1 Press [Start].
2 Use the cursor key to select the 1st paper cassette or bypass tray.
If necessary, you can change the paper size setting by following
procedures:
Press [Paper] then select the paper size using the cursor key and
then press ENTER.
3 Press [Start] to resume the printing.
To cancel this printing job:
1 If you want to cancel the current printing job, press [Cancel].
2 If you sure to cancel, press [Yes]. Otherwise, press [No].
O K t o C a n c e l ?
C u r r e n t P r i n t i n g J o b C a n c e l
[ Y e s ] [ N o ]
O p t i o n I n s t a l l E r r o r
S e l e c t S o u r c e /
A 4 < - - A 4
[ P a p e r ] [ S t a r t ]
O p t i o n I n s t a l l E r r o r
2 n d C a s s e t t e
N o O p t i o n i s D e t e c t e d :
[ C a n c e l ] [ S t a r t ]
O p t i o n I n s t a l l E r r o r
2 - b i n T r a y
N o O p t i o n i s D e t e c t e d :
[ C a n c e l ] [ S t a r t ]
O p t i o n I n s t a l l E r r o r
o r
1.27
Specified paper size.
Paper in the 1st cassette or bypass tray.
-
7/28/2019 35 5000 Print Controller Guide
38/108
cancelling the printing job
For MFX-1600 and MFX-1200
You can cancel a print job by pressing STOP on the control panel.
1 During printing, the printers LCD will show:
(STOP blinks.)
2 If you want to cancel the current printing, press STOP on theprinters control panel.
3 If you wish to do cancel the current print job, press CANCEL.If you wish to do not cancel the current print job, press STOP.
For F-320
To cancel a print job on the F-320:
During PC printing, the following display will appear on the LCD, and theLED of the ONLINE key blinks.
If you want to cancel the current printing job, follow the instructionsbelow:
1 Press ONLINE key on the F-320s control panel. These messages willalternate on the LCD:
and
2 If you wish to do cancel the current print job, press ENTER.If you wish to do not cancel the current print job, press CANCEL.
Cancel PC Print?No ! Cancel
Cancel PC Print?Yes !Enter
O N L I N E k e y
PC PrintingPage 1
Cancel PC Print?Yes:Cancel No:Stop
PrintingPage 1 Stop
1.28
-
7/28/2019 35 5000 Print Controller Guide
39/108
For F-360
To cancel a print job on the F-360:
During PC printing, the following display will appear on the LCD, and theLED of the ONLINE key blinks.
If you want to cancel the current printing job, follow the instructionsbelow:
1 Press ONLINE key on the F-360s control panel. The LCD will show:
2If you want to cancel the current printing job, press [Yes].Your machine will cancel the current printing job.
If you do not want to cancel the current printing job, press [No].
C u r r e n t P r i n t i n g J o b C a n c e l
O K t o C a n c e l ?
[ Y e s ] [ N o ]
O N L I N E k e y
R e a d y t o F a x
[ M o d e ] [ C o n t r a s t ]
P C P r i n t i n g
S e p 2 5 2 0 0 1 1 1 : 0 0 a m M e m : 1 0 0 %
1.29
-
7/28/2019 35 5000 Print Controller Guide
40/108
Using your machine on a Network
Connection through print server PC
When equipped with a printer controller, your fax machine can also bemade available to network users by connecting it to the network througha print server PC. In this arrangement, the Muratec machine with theOP-150 printer controller is connected to the print server PC with a bi-
directional parallel printer cable. The print server PC is connected to thenetwork through a network interface card inside the PC.
In this arrangement, the print server PC must be powered on, operatingand logged onto the network for the Muratec fax to be available for use asa printer.
EtherNet
Pri nt Data
Pri nt Server PC
1.30
-
7/28/2019 35 5000 Print Controller Guide
41/108
Connecting through optional network interface
When equipped with the printer controller and an optional network inter-face card, your fax machine can also be connected to following networkenvironment.
When you plan to use your fax machine as a PC printer in one of thesenetwork environments, you must setup the network settings as shown onthe following page.
Peer to peer network
Your Muratec machine can be used on peer-to-peer networks operatingwith Windows NT 4.0 workstation, Windows 95/98/Me and Windows
2000 PCs.
Client/Server network
Your Muratec machine can be used on client/server networks operatingwith Windows NT 4.0 workstation, Windows 2000, Windows 95/98/Meand Windows 3.1x clients, with Novell Netware 2.x/3.x/4.x, Windows NT
4.0 server on the server.
Pri nt Data
Pri nt Data
Pri nt Server PC
Cl i ent PC
EtherNet
EtherNet
Pri nt Data
1.31
-
7/28/2019 35 5000 Print Controller Guide
42/108
EtherNet connection
With the optional network interface card installation, a 10/100Base-T
EtherNet port will be added to your fax machine.
To connect to the network:
1 Turn off your fax machine.2 Connect the network cable to the Ethernet port.
3 Connect the other end of the network cable to the Ethernet.Note: If you need help with this step, contact your network admin-
istrator.
4 Turn on your fax machine.
Entering the IP Address
When you use the TCP/IP protocol, you must enter an IP Address, Subnetmask and Default Getaway for network use. See Set TCP/IP, pages1.361.38
Note:If you need help, contact your network administrator.
Installing the software for your network environment
Before you install the software, please see the License Agreement (nextpage).
EtherNet port Network cable(10/100Base-T twist pair cable)
1.32
-
7/28/2019 35 5000 Print Controller Guide
43/108
Software License Agreement
READ BEFORE INSTALLATIONThis Software License Agreement (hereinafter the Agreement) is a legal contract made
between you (regardless of an individual or a legal entity) and Murata Machinery, Ltd.
(hereinafter Murata) regarding the Murata software products contained in this CD-ROM(hereinafter the Software).
Please read the following terms carefully before installing the Software.
You can install and use the Software subject to your acknowledge and acceptance of all of the
following terms.
If you do not agree to any of the following terms, you should cancel the installing process.
The condition of the software license:
1. Any and all copyright and any other intellectual property regarding the Software remain
solely the property of NETsilicon,Inc. (hereinafter NETsilicon).2. You may use the Software only in the country of your purchase and only for the purpose
of using the hardware of Murata and other companies approved by Murata (hereinafter
OEM Companies).
3. You may use the Software only in compliance with notices and restrictions written in this
Manual contained in this package.
4. You must not modify, alter all or any part of the Software. You must not make any
attempt to discover the source code of the Software by any method including reverse-
engineering, de-compiling, or de-assembling.
5. You must not sell, transfer, rent, lease or sublicense the Software to any third party by
transmitting the software via phone-line or network, or by copying the software to floppy
disk, CD-ROM, magnetic data tape or any other media.
6. The software is subject to changes by Murata or NETsilicon in its specifications and pro-
gram without any prior notice.
7. Before installing the software, you are supposed to take any and all procedures necessary
to secure your records and data at your cost and responsibility, including making backup
of your computer files.
Neither Murata, NETsilicon, OEM Companies nor their distributors/sub-distributors
shall be liable for any damage or loss caused by your failure of taking the foregoing proce-
dure.
8. Neither Murata, NETsilicon, OEM Companies nor their distributors/sub-distributors
shall be liable for any damage or loss caused by (1) use of the software in combination
with the hardware other than the hardware which is defined in Section 2 above or (2)
modification of the software.
9. Neither Murata, NETsilicon, OEM Companies nor their distributors/sub-distributors
shall assume any damages incurred by you or a third party even if such damage is
directly/indirectly caused by use of the software or incapability to use the software.
If you acknowledge and acceptance of all of them, install the software followingsteps.
1.33
-
7/28/2019 35 5000 Print Controller Guide
44/108
To install the software for your network environment:
1 Insert the CD-ROM included in the optional NIC package into yourCD-ROM drive.
2 The following screen will appear automatically.
3 If your PC does not have the Adobe Acrobat Reader installed on it,first install it. To install the Acrobat Reader, click Install Acrobat
Reader on the screen.
4After you installed the Acrobat Reader, click Go to the CD ROM
Table of Contents on the screen. The Acrobat Reader will run and
the following screen will appear.
1.34
-
7/28/2019 35 5000 Print Controller Guide
45/108
5 Click item on the screen and install the software suitable for yournetwork environment by following the instructions that appear on
the screen.
Note:For details on how to use the settings and buttons, see on-line help.
Note:The Muratec NIC (network interface card) is not supports thefollowing protocols.
IPX-P2P in Windows NT and Windows 2000
IPP in Windows 2000
To remove the software
1 Close the software you want to uninstall.
2 Click on Start>Settings>Control Panel, then selectAdd/Remove Programs. The WindowsAdd/Remove Programsproperties box will appear.
3 Select software you want to remove, then clickAdd/Remove but-ton.
4 Follow the instructions that appear on the screen.
1.35
-
7/28/2019 35 5000 Print Controller Guide
46/108
Set TCP/IP
When using the TCP/IP protocol, enter the IP Address, Subnet mask anddefault Getaway.
Note:To access this function, the optional NIC (Network Interface Card)
must be installed. Contact your network administrator if you have
questions about these settings.
To enter your network settings:
For MFX-1600 and 1200:
1 Press Program key, B, 4, 0, 1.
2 Press ENTER. The LCD will show:
3 Enter the IP Address for your printer using the numeric keypad,then press ENTER to save the setting.
For example, if your printers IP Address is 200.1.37.47, you should
press 2 0 0 0 0 1 0 3 7 0 4 7.
4 Press ENTER. The LCD will show:
5 Enter Subnet Mask address.
6 Press ENTER. The LCD will show:
7 Enter default Gateway.
8 Press ENTER to save the setting. The machine will return tostandby mode.
9 To effect the TCP/IP setting, turn the machine off and then turn on.
Set Default Gateway000.000.000.000
Set Subnet Mask000.000.000.000
Set IP Address000.000.000.000
01 TCP/IP"/#/Enter
1.36
-
7/28/2019 35 5000 Print Controller Guide
47/108
For F-320:
1 Press MENU, 2, 4, 1.
2 Press ENTER.
3 Enter the IP Address for your printer using the numeric keypad,then press ENTER to save the setting.
4 Press ENTER.
5 Enter Subnet Mask address.
6 Press ENTER.
7 Enter default Gateway.
8 Press ENTER to save the setting.The machine will return to standby mode.
9 To effect the TCP/IP setting, turn the machine off and then turn on.
Set Default Gateway000.000.000.000
Set Subnet Mask000.000.000.000
Set IP Address000.000.000.000
1 TCP/IP!/$/Enter
1.37
-
7/28/2019 35 5000 Print Controller Guide
48/108
For F-360:
1 Press MENU, 2, 4, 0, 1, ENTER.
2 Select IP Address using the cursor key. Then press ENTER.
3 Enter the IP Address for your printer using the numeric keypad.Then press ENTER.
4 Select Subnet Mask using the cursor key. Then press ENTER.
5 Enter the Subnet Mask address using the numeric keypad.Then press ENTER.
6 Select Gateway using the cursor key. Then press ENTER.
7 Enter the default gateway address using the numeric keypad.Then press ENTER.
8 Select Exit to exit this setting mode.To return to standby mode, press STOP.
9 To effect the TCP/IP setting, turn the machine off and then turn on.
0 1 . T C P / I P
S e t D e f a u l t G e t a w a y
0 0 0 . 0 0 0 . 0 0 0 . 0 0 0
0 1 . T C P / I P
S e t S u b n e t M a s k
0 0 0 . 0 0 0 . 0 0 0 . 0 0 0
0 1 . T C P / I P
S e t I P A d d r e s s
0 0 0 . 0 0 0 . 0 0 0 . 0 0 0
0 1 . T C P / I P
E x i t
I P A d d r e s s : 0 0 0 . 0 0 0 . 0 0 0 . 0 0 0
S u b n e t M a s k : 0 0 0 . 0 0 0 . 0 0 0 . 0 0 0
1.38
-
7/28/2019 35 5000 Print Controller Guide
49/108
Appendix
Print the Demo Page
The demo page provides a demonstration that highlights the features andfunctions of the printer.
To print the demo page:
For MFX-1600 and 1200 only:
1 Press Program key, E, 2, 0, 1.
2 Press ENTER to print the demo page.
Print the Printer Configuration Page
The printer configuration page lists the status and configuration of theprinter.
To print the printer configuration page:
For MFX-1600 and 1200:
1 Press Program key, E, 2, 0, 2.
2 Press ENTER to print the printer configuration page.
For F-320:
1 Press MENU, 5, 2, 1.
2 Press ENTER to print the printer configuration page.
1 Status Page!/$/Enter
02 Status Page"/#/Enter
01 Demo Page"/#/Enter
1.39
-
7/28/2019 35 5000 Print Controller Guide
50/108
For F-360:
1 Press MENU, 5, 2, 0, 1.
2 Press ENTER to print the printer configuration page.
Print PCL Font List
The PCL font list provides a list of all PCL fonts currently installed in theprinter.
To print the PCL font list:
For MFX-1600 and 1200:
1 Press Program key, E, 2, 0, 3.
2 Press ENTER to print the PCL font list.
For F-320:
1 Press MENU, 5, 2, 2.
2 Press ENTER to print the PCL font list.
For F-360:
1 Press MENU, 5, 2, 0, 2.
2 Press ENTER to print the PCL font list.
2 . P r i n t e r F u n c t i o n s
0 1 . S t a t u s P a g e
0 2 . F o n t L i s t
0 3 . N I C S t a t u s
2 Font List!/$/Enter
03 Font List"/#/Enter
2 . P r i n t e r F u n c t i o n s
0 1 . S t a t u s P a g e
0 2 . F o n t L i s t
0 3 . N I C S t a t u s
1.40
-
7/28/2019 35 5000 Print Controller Guide
51/108
Print NIC status
Note:To access this function, the optional NIC (Network Interface Card)
must be installed.
To print the NIC status:
For MFX-1600 and 1200:
1 Press Program key, E, 2, 0, 4.
2 Press ENTER to print the NIC status.
For F-320:
1 Press MENU, 5, 2, 3.
2 Press ENTER to print the NIC status.
For F-360:1 Press MENU, 5, 2, 0, 3.
2 Press ENTER to print the NIC status.
2 . P r i n t e r F u n c t i o n s
0 1 . S t a t u s P a g e
0 2 . F o n t L i s t
0 3 . N I C S t a t u s
3 NIC Status!/$/Enter
04 NIC Status"/#/Enter
1.41
-
7/28/2019 35 5000 Print Controller Guide
52/108
Paper
The printer mode supports printing on the following sized paper. Also,indicated is the paper source where each paper can be loaded.
Paper Size C1 C2 Bypass TrayLegal (S) 8.5 14 No No Yes
Letter (S) 8.5 11 No No Yes
Half Letter (L) 8.5 5.5 No No Yes
Executive (S) 7.25 10.5 No No Yes
A4 (S) 210 297 mm Yes Yes Yes
A5 (S) 148 210 mm No No Yes
A5 (L) 210 148 mm Yes Yes Yes
A6 (S) 105 148 mm No No Yes
F4 (S) 210 330 mm Yes Yes Yes
COM 10 (S) 4.125 9.5 No No Yes
Monarch (S) 3.875 7.5 No No Yes
DL (S) 110 220 mm No No Yes
Postcard (S) 100 148 mm No No Yes
Custom Paper ScanningNo No
97 mm to 216 mm
Direction 3.82to 8.5
FeedNo No
140 mm to 356 mm
Direction 5.5to 14.0
S: Short edge feeding, L: Long edge feeding
C1: 1st paper cassette
C2: 2nd paper cassette
1.42
-
7/28/2019 35 5000 Print Controller Guide
53/108
AGFA Font Manager
AGFA Font Manager helps you manage your fonts in Microsoft Windows.
Note:AGFA Font Manager requires Windows 95/98, Windows Me,
Windows NT 4.0 or Windows 2000.
To install:
1 Insert the CD-ROM into your CD-ROM drive.
2 Click Start, then select Run.
3 Type X:\Font\Setup.exe (X is the drive letter for your CD-ROMdrive).
You can also browse through the folders to find the Setup.exe fileby clicking Browse button.
4 Click OKto start the software installation program.5 Follow the instructions that appear on the screen.
Using the font manager:
For full details about how to use AGFA Font Manager, click the Helpbutton on the AGFA Font Manager window.
1.43
-
7/28/2019 35 5000 Print Controller Guide
54/108
Index
CCancelling the printing job . . . . . . . . . . 1.28
for F-320 . . . . . . . . . . . . . . . . . . . . . . . . 1.28for F-360 . . . . . . . . . . . . . . . . . . . . . . . . 1.29for MFX-1600/1200 . . . . . . . . . . . . . . . 1.28
DDemo Page . . . . . . . . . . . . . . . . . . . . . . . 1.39Doc. Pilot . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1
E
Error Messages . . . . . . . . . . . . . . . . . . . 1.13for F-320 . . . . . . . . . . . . . . . . . . . . . . . . 1.18for F-360 . . . . . . . . . . . . . . . . . . . . . . . . 1.23for MFX-1600/1200 . . . . . . . . . . . . . . . 1.13
IInstallation . . . . . . . . . . . . . . . . . . . . . . . . 1.3
for Windows NT 4.0 . . . . . . . . . . . . . . . 1.7Doc. Pilot and Remote Shuttle . . . . . . 1.7Setting up the printer with the PCL
driver . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8for Windows 2000 . . . . . . . . . . . . . . . . . 1.3Doc. Pilot and Remote Shuttle . . . . . . 1.3Setting up the printer with the PCLdriver . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4
for Windows 3.1 . . . . . . . . . . . . . . . . . . 1.9Doc. Pilot and Remote Shuttle . . . . . . 1.9Setting up the printer with the PCLdriver . . . . . . . . . . . . . . . . . . . . . . . . . 1.10
for Windows 95/98/Me . . . . . . . . . . . . . 1.5Doc. Pilot and Remote Shuttle . . . . . . 1.5
Setting up the printer with the PCLdriver . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6
NNetwork . . . . . . . . . . . . . . . . . . . . . . . . . 1.30
Connect to the EtherNet . . . . . . . . . . . 1.32Environment . . . . . . . . . . . . . . . . 1.30-1.31Installing the software . . . . . . . . . . . . 1.34IP Address . . . . . . . . . . . . . . . . . . . . . . 1.32Optional Network Interface Card . . . 1.31
Print NIC status . . . . . . . . . . . . . . . . 1.41Remove the software . . . . . . . . . . . . . . 1.35Set TCP/IP . . . . . . . . . . . . . . . . . . . . . . 1.36
for F-320 . . . . . . . . . . . . . . . . . . . . . . 1.37for F-360 . . . . . . . . . . . . . . . . . . . . . . 1.38for MFX-1200/1600 . . . . . . . . . . . . . . 1.36
PPaper . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.42PCL Font List . . . . . . . . . . . . . . . . . . . . . 1.40Printer Configuration Page . . . . . . . . . . 1.39
RRemote Shuttle . . . . . . . . . . . . . . . . . . . 1.11About Remote Shuttle . . . . . . . . . 1.1, 1.11
Enlarged view . . . . . . . . . . . . . . . . . . . 1.11Reduced view . . . . . . . . . . . . . . . . . . . . 1.11Setting up the printer environment . . 1.12
Removing software . . . . . . . . . . . . . . . . . . 1.4for Windows 2000 . . . . . . . . . . . . . . . . . 1.4for Windows 3.1 . . . . . . . . . . . . . . . . . . . 1.9for Windows 95/98/Me . . . . . . . . . . . . . . 1.6for Windows NT4 . . . . . . . . . . . . . . . . . . 1.8
SSoftware License Agreement
for NP-200 . . . . . . . . . . . . . . . . . . . . . . 1.33System requirements . . . . . . . . . . . . . . . . 1.1
1.44
-
7/28/2019 35 5000 Print Controller Guide
55/108
Chapter 2
Using the Muratec machineas a scanner
-
7/28/2019 35 5000 Print Controller Guide
56/108
This TWAIN-compliant scanner driver is developed by Destiny Technology
Corporation and is protected under the Copyright Law in various countries. Copy,
distribution, modification, use or any other disposal thereof is not allowed unless
otherwise authorized in this Operating Instructions.
-
7/28/2019 35 5000 Print Controller Guide
57/108
System requirementsThe following are the minimum computer requirements to install andoperate the Muratec TWAIN driver.
Supporting PC:
IBM-PC / AT Compatible
CPU:i486DX/66MHz or higher
Note: We recommend Pentium/150MHz or higher.
Operating System:Windows 95/98/Me, Windows NT 4.0 or Windows 2000
Hard Disk Drive:At least 10MB of available disk space for installing
RAM:At least 32 MB
Application Interface:TWAIN Driver compatible
TWAIN Driver Version: Version 1.9
Terminal Connector Interface:A bidirectional parallel interface IEEE1284 (Compatiblemode / Nibble mode / ECP mode)
Supporting Application Software:Application software which supports TWAIN.Muratec has tested the following packages:
I.R.I.S. Readiris PRO 6 ScanSoft PaperPort DELUXE 7.0 Wordcraft Unimessage Pro Version1.0 Wordcraft Unimessage XLite Version1.1Adobe Acrobat Capture 3.0 ScanSoft TextBridge Pro Millennium Version9.5 Caere OmniPage Pro 10.0 Microsoft Word 2000 Microsoft Excel 2000 Microsoft PowerPoint 2000 Kodak Imaging for Windows 95/98/Me/2000
Note:Actual requirements will vary based on your PC system configura-
tion, the applications and the image you will scan.
2.1
-
7/28/2019 35 5000 Print Controller Guide
58/108
InstallationFollow the steps below to install the Muratec TWAIN driver forWindows 95, Windows 98, Windows Me, Windows NTversion 4.0 orWindows 2000.
Before you install the software, you must read the README. TXT file inthe appropriate directory of the CD-ROM for important last-minuteinstallation information and helpful hints:
X:\Scanner\XXXXX\README.TXT
Note: X is the drive letter for your CD-ROM drive. In XXXXX, the
following folder name will be applied according to your Windows
version:
Windows 95/98/Me : Win9x_Me Windows NT 4.0/2000 : WinNT4_2000
To install the TWAIN driver
1 Start Windows.Note: If you are using Windows NT 4.0 or Windows 2000, you
must log in as the Administrator to install (or uninstall) the
Muratec TWAIN driver.
2 Insert the Muratec OP-150 CD-ROM into your CD-ROM drive.3 Click Start and then Run.
4 Type X:\Scanner\XXXXX\Setup.exe.Note: X is the drive letter for your CD-ROM drive. XXXXX is the
folder name which means your Windows version. (See above)
You can also browse through the folders to find the Setup.exe file
for your version of Windows by clicking Browse.
5 Click OKto start the installer software.
6 Follow the instructions that appear on the screen.
To uninstall the TWAIN driver
1 To start the uninstaller program, click onStart>Settings>Control Panel>Add/Remove Programs,
then select Muratec TWAIN Driver and click onAdd/Remove.
2 Follow the instructions that appear on the screen.
2.2
-
7/28/2019 35 5000 Print Controller Guide
59/108
Getting ready to use the MuratecTWAIN driverBefore you use the Muratec TWAIN driver, the following things must be
true: The Muratec machine is connected to your PC using the bi-directional
parallel interface cable. The Muratec TWAIN driver has been installed in your PC.You must have software that supports TWAIN scanning.
(See page 2.1)
For your information in using the Muratec TWAIN driver
Scanning modeMuratecs TWAIN scanning lets you scan documents two different ways:
Real-time scanning modeWhen you use the real-time scanning mode, or RS mode, your Muratecmachine will scan and transfer document images to your PC immedi-ately. RS mode is the mode most like traditional document scanners.
Scan-box modeWhen you choose the scan-box mode, or SB mode, your Muratecmachine will scan and store the image data into a scan box. You canretrieve the scanned data from the scan box by using the TWAINdriver anytime.
Scanner settingsYou should make the following settings before scanning. If you chooseRS mode, make these settings from your PC. If you choose SB mode,set them using the control panel on your Muratec machine.Regarding the initial settings and details, refer to The list of scanner
settings on page 2.44. Scan size Set the size you will scan.
Document type Set the document type according to the document
you want to scan. You can select from:
Photo Select this mode when scanning photographs or drawings.Photo/Text Select this mode when scanning documents containing
photographs or drawings and text.Text Select this mode when scanning text.
Contrast Sets how light or dark you want the documents to be.
2.3
-
7/28/2019 35 5000 Print Controller Guide
60/108
Resolution If your machine is MFX-1600, you can choose to scan
at 200 dpi, 300 dpi, 400 dpi or 600 dpi resolution. Scanning at 600 dpiprovides greater detail in scanned images, but creates large files and
uses more memory in your PC and your Muratec machine.
Note:600 dpi setting is available only for the MFX-1600.
Note:Scanning enlargement is not available at 600 dpi.
If your machine is MFX-1200, the resolution is fixed at 300 dpi.
If your machine is F-360, you can choose to scan at 200 dpi, 300 dpi or400 dpi.
If your machine is F-320, you can choose to scan at 200 dpi or 300 dpi.
Reduce/Enlarge You can reduce or enlarge the document once itis scanned. Select one of the preset rates, or enter the desired ratio by
1 percent increments.
Note: If your machine is MFX-1600 or MFX-1200, the enlargement isavailable only for scanning using the FBS. It is not available forscanning through theADF.
Note: If your machine is F-360 or F-320, the enlargement is not available.
Change your machine to the Scanner mode
MFX-1600/1200: F-360/320:Press COPY/FAX/SCAN key Press COPY/SCAN key
Priority
The OP-150 allows you to use the Muratec machine as a PC printer and aPC scanner through the unit's single bidirectional parallel interface port.It is, however, not possible to use both functions at the same time. In orderto avoid conflict between these two functions, when you use the MuratecTWAIN driver while the Remote Shuttle is working, the TWAIN driverwill request to close the Remote Shuttle.
ADF/FBS auto-switching for MFX-1600 and MFX-1200
Muratecs TWAIN scanning option allows you to scan from either theautomatic document feeder or the flatbed scanner. Muratecs scanner will
automatically detect whether your document is in the ADF or the FBS.
If you have documents placed in the ADF and FBS at the same time, thescanner will scan the document from the ADF first.
C o p y / S c a n k e y
C
o
p
y
M
F a x
M
S
c
a
n
C o p y / F a x / S c a n k e y
2.4
-
7/28/2019 35 5000 Print Controller Guide
61/108
Scanning the image
Access to the Muratec TWAIN driver
Follow the steps below to access the Muratec TWAIN driver from your
application software:
1 Turn on your Muratec machine.
2 Start the application software that supports TWAIN scanning.
3 Select Muratec TWAIN Driver in your application software. (Ifyou need help, refer to your softwares help file.)
If you use the Kodak Imaging application often included with your
Windows operating CD, choose Select Scanner from the File
menu, choose Muratec TWAIN Driver then click OK. ChoosingScan New from the File menu, the following window will appear:
Note: The Kodak Imaging application included withWindowsNT4.0 does not support TWAIN. Use other applica-
tion to access to the TWAIN driver.
When you want to use the RS mode, select RS mode tab.
When you want to use the SB mode, select SB mode tab.
When you want to see information about the Muratec TWAINdriver, select About tab.
Note: Type 2 at the top of the window means your machine is anMFX-1600. If it is an MFX-1200, it will say Type 1. If it is an
F-360, it will say Type 4. If it is an F-320, it will say Type 5.
2.5
-
7/28/2019 35 5000 Print Controller Guide
62/108
Using the RS mode
Scanning with RS mode
1 Follow the steps in Access to Muratec TWAIN driver on page 2.5to show the following window:
2 Select the desired elements for each setting. (Refer to The list ofscanner settings on page 2.44, if necessary.)
If you want to Reduce/Enlarge by 1 percent increments, click the
check-box next to Zoom and enter a ratio.Note: The enlargement is available only for MFX-1600 and MFX-
1200, and it is available only for scanning using the FBS (FlatbedScanner). It is not available for scanning through the ADF(Automatic Document Feeder).
Note: If your machine is MFX-1600, scanning enlargement is not
available at 600 dpi. Select other resolution, or select 100%
for the ratio.
Note: If your machine is F-360 or F-320, scanning enlargement isnot available.
2.6
-
7/28/2019 35 5000 Print Controller Guide
63/108
The buttons on the window mean:
OK When you have finished adjusting the settings, click this
button.
Cancel If you want to close the window without scanning,
click this button.
Default If you want to set all values to default, click this
button.
Help If you want to see the on-line help, click this button.
3 On your machine, change the machines mode to scan mode.
If your machine is MFX-1600:Press COPY/FAX/SCAN to change to Scan mode.
If your machine is MFX-1200:To change to scan mode by pressing COPY/FAX/SCAN.
If your machine is F-360:To change to scan mode by pressing COPY/SCAN.
If your machine is F-320:To change to scan mode by pressing COPY/SCAN.
4 Set the document you want to scan.
5 On your PC, click OKto start scanning.The following window will appear:
Scan Ready !200dpiAuto 100%
E n t e r S c a n B o x N o . ( 0 1 - 2 0 ) : _
[ D o c . T y p e ] [ R e s o l u t . ] [ C o n t r a s t ]
T e x t 2 0 0 d p i N o r m a l
R a t i o : 1 0 0 % M e m : 9 8 %
Scan ReadyA4 100%
Scan Ready 200dpiA4 100%
2.7
-
7/28/2019 35 5000 Print Controller Guide
64/108
Note: If you want to cancel the job during scanning or data transfer,
click Cancel button.
6 When scanning is finished, the window will close and the scannedimage will appear.
2.8
-
7/28/2019 35 5000 Print Controller Guide
65/108
Using the SB mode
When the OP-150 is installed, the scan boxes in which the image data willbe stored are made in your machine. The scan box specifications are asfollows:
Number of Boxes: 20 boxes
Set by two-digits from 01 to 20.
Number of Files/Box: 10 files/box
ID Code: Each box has an ID Code.
Set by four-digits from 0001 to 9999 .
Note:The number of pages which can be stored in a file depends on your
machines memory capacity, the resolution and type ofdocument(s).
The basic operation for the SB mode
The operation for the SB mode is summarized as follows:1 Register the scan box. (See pages 2.102.15)
2 Scan the document with your machine. The scanned data will be storedinto the scan box. (See pages 2.112.20)
3 Retrieve the scanned data from the scan box. (See pages 2.302.32)
X
X
2.9
-
7/28/2019 35 5000 Print Controller Guide
66/108
Register or modify a scan box
For MFX-1600 and 1200:
1 Press Program key, C, 6, 0, 1, ENTER. The LCD will show:
2 Use the numeric keypad to enter a desired scan box number.Here, weve entered 0, 3 and the LCD will show:
Important: When entering a scan box number less than 10, you mustenter a leading zero to make two digits. For example,01 09.
3 Press ENTER.If you want to register the scan box or you have set 0000 for the I.D. codeof this scan box, skip to step 5.If you want to modify the scan box, the LCD will ask you to enter theproper I.D. code. The LCD shows:
4 Use the numeric keypad to enter the 4-digit I.D. code and then pressENTER.
Note: If you enter an invalid I.D. code, the fax machine rejects theattempt and stops the operation.
5 The LCD asks you to enter the scan box name. The LCD will show:
If you have already named the box and do not want to change it, skip tostep 7.If you want to name the box for the first time or change the name, go onto step 6.
03:Box Name;Upper_
03:Set Scan BoxEnter I.D. Code:****
Select Scan Box03:Not Registered
Select Scan Box01:Not Registered
2.10
-
7/28/2019 35 5000 Print Controller Guide
67/108
6 Enter the name by using the one-touch keys. (If necessary, refer toEntering characters on pages 2.402.41.) A scan boxs name can be upto 16 characters in length.
Note:You must enter characters when using a scan box. If you
enter nothing or only spaces, the machine beeps and briefly
shows:
7 Press ENTER.The LCD now asks if you want to erase the files in this boxafter transferring to the PC.
8 Press or until the mode you want appears.
9 Press ENTER.The LCD now asks for your scan boxs four-digit securityI.D. code. The LCD shows:
If you do not want to change the I.D. code, skip to step 12.
10 Decide on a four-digit I.D. code (0001 9999) for this scan box.Write it down, and put it in a safe place.
11 Use the numeric keypad to enter the four-digit I.D. code for the scan box.Note: If you want to turn off the I.D. code, enter 0000.
12 Press ENTER.To create or modify another scan box, repeat steps 212.
To finish, press STOP.
03:Set Scan BoxEnter I.D. Code:0000
Erase Trans Doc :Off!/"/Enter
03:Box Name;UpperEnter Box Name
2.11
-
7/28/2019 35 5000 Print Controller Guide
68/108
For F-320:
1 Press MENU, 3, 7, 1, ENTER.
2 Use the numeric keypad to enter a desired scan box number.Here, weve entered 0, 3 and the LCD will show:
Important: When entering a scan box number less than 10, you mustenter a leading zero to make two digits. For example,01 09.
3 Press ENTER.If you want to register the scan box or you have set 0000 for the I.D. codeof this scan box, skip to step 5.If you want to modify the scan box, the LCD will ask you to enter theproper I.D. code. The LCD shows:
4 Use the numeric keypad to enter the 4-digit I.D. code and then pressENTER.
Note: If you enter an invalid I.D. code, the fax machine rejects theattempt and stops the operation.
5 The LCD asks you to enter the scan box name. The LCD will show:
If you have already named the box and do not want to change it, skip tostep 7.If you want to name the box for the first time or change the name, go onto step 6.
03:Box Name;Upper_
03:Set Scan BoxEnter I.D. Code:****
Select Scan Box03:Not Registered
Select Scan Box01:Not Registered
2.12
-
7/28/2019 35 5000 Print Controller Guide
69/108
6 Enter the name by using the one-touch keys. (If necessary, refer toEntering characters on pages 2.422.43.) A scan boxs name can be upto 16 characters in length.
Note:You must enter characters when using a scan box. If you
enter nothing or only spaces, the machine beeps and briefly
shows:
7 Press ENTER.The LCD now asks if you want to erase the files in this boxafter transferring to the PC.
8 Press or until the mode you want appears.
9 Press ENTER.The LCD now asks for your scan boxs four-digit securityI.D. code. The LCD shows:
If you do not want to change the I.D. code, skip to step 12.
10 Decide on a four-digit I.D. code (0001 9999) for this scan box.Write it down, and put it in a safe place.
11 Use the numeric keypad to enter the four-digit I.D. code for the scan box.Note: If you want to turn off the I.D. code, enter 0000.
12 Press ENTER.To create or modify another scan box, repeat steps 212.
To finish, pressSTOP
.
03:Set Scan BoxEnter I.D. Code:0000
Erase Trans Doc :Off#/$/Enter
03:Box Number;UpperEnter Box Name
2.13
-
7/28/2019 35 5000 Print Controller Guide
70/108
For F-360:
1 Press MENU, 3, 7, 0, 1, ENTER.
2 Use the numeric keypad to enter a desired scan box number.Important: When entering a scan box number less than 10, you must
enter a leading zero to make two digits. For example,01 09.
3 Press ENTER.
If you want to register the scan box or you have set 0000 for the I.D. codeof this scan box, skip to step 5.If you want to modify the scan box, the LCD will ask you to enter theproper I.D. code. The LCD shows:
4 Use the numeric keypad to enter the 4-digit I.D. code and thenpress ENTER.Note: If you enter an invalid I.D. code, the fax machine rejects the
attempt and stops the operation.
5 The LCD asks you to enter the scan box name.
If you have already named the box and do not want to change it, skip tostep 7.If you want to name the box for the first time or change the name, go onto next step.
6 Enter the name by using the numeric keypad. (If necessary, refer toEntering characters on pages 2.422.43.) A scan boxs name can be upto 16 characters in length.
Note:You must enter characters when using a scan box.
0 1 . S e t B o x
_
E n t e r B o x N a m e U p p e r C a s e
0 1 . S e t B o x
_
E n t e r I . D . C o d e
0 1 . S e t S c a n B o x
0 1 : N o t S t o r e d
E n t e r B o x N u m b e r ( 0 1 - 2 0 ) : _
2.14
-
7/28/2019 35 5000 Print Controller Guide
71/108
7 Press ENTER.The LCD now asks if you want to erase the files in this boxafter transferring to the PC.
8 Use or to select On or Off.
9 Press ENTER.The LCD now asks for your scan boxs four-digit securityI.D. code. The LCD shows:
If you do not want to change the I.D. code, skip to step 12.
10 Decide on a four-digit I.D. code (0001 9999) for this scan box.Write it down, and put it in a safe place.
11 Use the numeric keypad to enter the four-digit I.D. code for the scan box.Note: If you want to turn off the I.D. code, enter 0000.
12 PressENTER
.To create or modify another scan box, repeat steps 212.To finish, press STOP.
0 1 . S e t B o x
0 0 0 0
E n t e r I . D . C o d e
0 1 . S e t B o x
O N
O F F
E r a s e D o c . a f t e r T r a n s f e r ?
2.15
-
7/28/2019 35 5000 Print Controller Guide
72/108
Scanning the image into a scan box
Important: You should register the scan box before scanning.
For MFX-1600 and 1200:
1 Press COPY/FAX/SCAN to change to Scan mode.
Note: If your machine is an MFX-1200, the resolution is not
displayed on the LCD.
2 Set the document in theADF or on the FBS glass.
3 Adjust the following settings. (Refer to The list of scannersettings on page 2.44, if necessary.) Scan size Press DOCUMENT SIZE to select the scan size you want. Resolution Press or to select the resolution you want.
Note: This setting is available only for the MFX-1600.
Document type Press DOCUMENT to select the document type youwant.
Contrast Press CONTRAST to select the contrast you want.
Reduction/Enlargement Press , or ZOOM to select the ratioyou want. (Refer to the Operating Instructions of your machine, formore details.)
4 Press START.The LCD will show:
5 Use the numeric keypad to enter the desired scan box number.Here, weve entered 0, 3 and the LCD will show:
Important: When entering a scan