3233 FRICK RD. HOUSTON, TX. 77086 OFFICE 281… · “your metal building solution” 3233 frick...

13
“YOUR METAL BUILDING SOLUTION” 3233 FRICK RD. HOUSTON, TX. 77086 OFFICE 281.999.8810 & FAX 281.999.8811

Transcript of 3233 FRICK RD. HOUSTON, TX. 77086 OFFICE 281… · “your metal building solution” 3233 frick...

“YOUR METAL BUILDING SOLUTION”

3233 FRICK RD. HOUSTON, TX. 77086OFFICE 281.999.8810 & FAX 281.999.8811

Single Slope Metal Building Types

Clear Span System

One Interior Column System

Two Interior Column System

Single Slope: A stand alone building with a sloping roof in one plane. The slope is from one wall to the opposite wall.

“YOUR METAL BUILDING SOLUTION”

Double Slope Metal Building Types

Clear Span System

One Interior Column System

Two Interior Column System

Double Slope: A stand alone building in which the ridge is at the centerof the building.

“YOUR METAL BUILDING SOLUTION”

Bar Joist Metal Building

Bar joist systems are mainly used for bay spacing’s from 35’ up to 65‘Some Advantages Are:•Optimum Bay Spacing & Column Locations •Can Mix with Traditional Purlins •Use with Steel Deck, Built Up and Single Ply •Design Flexibility (Can Be Used With CMU Wall & Tilt Wall Systems)

“YOUR METAL BUILDING SOLUTION”

“YOUR METAL BUILDING SOLUTION”

3233 FRICK RD. HOUSTON, TX. 77086OFFICE 281.999.8810 & FAX 281.999.8811

Carne Buildings

Crane Buildings: The building crane is a complex structural systemconsisting of the crane with trolley and hoist,crane rails, and crane runway beams, structural supports, stops and bumpers.

Crane Types:

• Bridge Cranes - Top running and Under Hung• Monorail• Jib

“YOUR METAL BUILDING SOLUTION”

Lean To

Lean To Always Connected To Building Main Fame

Single Slope: Lean-To: Ideally suited to give you that extra space you need alongside your building. The Lean-To ties in at the eave of your building or below the eave and can provide a variety of uses...from just a covered area to a completely enclosed addition to your building.

“YOUR METAL BUILDING SOLUTION”

Canopy

Canopy: An overhanging or projecting roof structure off the sidewall or endwall with the extreme end usually unsupported. Mainly usedfor aesthetic application or to cover driveway or walkway.

Basic Options:

Face Panel and Soffit Vary with panel type.

Canopy can project out 15' unsupported with or without a cantilever beam with exposed red iron. Larger canopy sizes available by special design and engineering.

“YOUR METAL BUILDING SOLUTION”

Facades

Facades: A decorative trim or panel system projecting from the face of a wall panel. Gauges vary and are dependent on design loads.Used for aesthetic application.

Basic Options:

Soffit elevation must be at least 2'-0" below eave, minimum projection is 1'-6", maximum projection is 6'-0", and maximum height is 9'-0". Mansard/fascia must be 6" higher than the peak on the endwall and 6" higher than the eave on the sidewall.

“YOUR METAL BUILDING SOLUTION”

“YOUR METAL BUILDING SOLUTION”

3233 FRICK RD. HOUSTON, TX. 77086OFFICE 281.999.8810 & FAX 281.999.8811

Common Metal Building Accessories

These accessories are exclusively for metal buildings

Standard TrimGutters Down Spouts

Options You Can Chose From:

PSK (Polypropylene/Scrum/Kraft) InsulationR-19 6”R-16 5”R-13 4” Standard For RoofR-10 3” Standard For Wall & Can Be Used For Roof

Ridge Vents 9” Throat x 10’ Long12” Throat x 10’ Long

Walk Doors (All Doors Have Options For Glass Window & Dead Bolt)3070,4070 & 6070

Windows3030, 4030,6030 & 6070

Frame Openings For Overhead Doors & Glass Doors

“YOUR METAL BUILDING SOLUTION”

PBR Panel

This panel is used both for the roof and walls, the "PBR" panel's deep ribs create an even-shadowed appearance. The area between the ribs is reinforced.

Gauge: 26, 24

Lengths: 45' maximum is standard but longer lengths available by special request.

Fasteners: Standard coated, CAD plated or zinc-aluminum cast head screw

Dimensions: 36" coverage x 1 1/4" deep.

Finish: Galvalume and Silicone Polyester

Usage: Roof, wall, liner, mansard, and soffit panel applications.

Limitations: 1/2:12 pitch or greater. Not designed for coverage over bar joist.

“YOUR METAL BUILDING SOLUTION”

Vazquez Metal Buildings And Components manufactures and designs custom metal buildings of the highest quality, durability and longevity based in Houston, Texas. Our welders & procedures are certified by the American Welding Society.

The continued success of VMBC can be attributed to a focus on customer service that solidifies long lasting business relationships.

All of VMBC products and systems are produced within our own plant. Our manufacturing facility enables us to manufacture orders quickly and accurately, while giving us the ability to reach necessary time to deliver finished projects.

Our approach to selling metal buildings is to offer our customers the best quality metal building structures with a quality control staff onboard to perform in house ndtservices we can assure you that you are getting the best building you can buy. Feel free to give us call one of our courteous representatives will answer all your questions and get you a free Metal building quote as soon as possible.

Our metal buildings include the following:

Anchor BoltsAnchor Bolt DrawingsErection DrawingsEngineer Drawings For Permits (Permits By Others)Erection Houston & Harris County Area (Optional)

“YOUR METAL BUILDING SOLUTION”

3233 FRICK RD. HOUSTON, TX. 77086OFFICE 281.999.8810 & FAX 281.999.8811