How to Perform Self Hypnosis_ 10 Steps (With Pictures) - WikiHow
3 Ways to Install a Residential Telephone Jack - WikiHow (2014!06!11 04-17-47 UTC)
-
Upload
watermelontaco -
Category
Documents
-
view
13 -
download
1
description
Transcript of 3 Ways to Install a Residential Telephone Jack - WikiHow (2014!06!11 04-17-47 UTC)
12/12/13 3 Ways to Install a Residential Telephone Jack - wikiHow
www.wikihow.com/Install-a-Residential-Telephone-Jack 1/13
How to Install a Residential TelephoneJack
Prepare for the Installation Replace an Old Jack With a New One Install a New Jack in a Different Part
of the Room
You may want to install a new telephone jack in your home if your old one isn’t
working, or if your phone lines aren’t accessible where you need them. Instead
of calling the phone company to request their services, try installing the new
phone jack yourself. With just a few tools and this step by step guide, you can
skip the phone company’s fees and have the satisfaction of executing your own
home improvement project.
1 Choose a new jack. Most phone jacks cost about $3.00 to $5.00 and are available
at hardware stores. Find a jack that best fits your needs, whether it’s a simple flush
plate, a wall mount jack, or a baseboard jack. Jacks come in several different shapes and
colors, and you’ll probably want to choose one that blends in well with your room’s decor.
If you’re replacing an old jack that needs repairing, the simplest choice is a new
jack with the same size and shape as the old one. For example, if your old jack is a
standard rectangular wall plate, it will be easiest to install a new jack that looks very
similar. This way you won’t have to drill a new hole in your wall to accommodate a
new jack size.
If you plan to attach your telephone to the wall, make sure you buy a wall mount
jack, rather than a flush jack. A wall mount jack juts out from the wall, providing a
structure on which to mount your telephone. A flush jack lies flat against the wall,
allowing you to plug in your phone, but not mount it.
Part 1 of 3: Prepare for the Installation
12/12/13 3 Ways to Install a Residential Telephone Jack - wikiHow
www.wikihow.com/Install-a-Residential-Telephone-Jack 2/13
Baseboard jacks are small plastic or metal boxes that are affixed to your
baseboard, with the jack opening on the bottom edge of the box. If you’re
concerned about aesthetics, this may be a more discreet option than a wall plate.
If you’re planning on using the jack for both a DSL internet connection and a phone
line, choose a jack with two openings, often called a duplex jack, so that you can
run two separate lines.
12/12/13 3 Ways to Install a Residential Telephone Jack - wikiHow
www.wikihow.com/Install-a-Residential-Telephone-Jack 3/13
2 Find your home’s Network Interface Device (NID) and disconnect your phone
line. The NID is a device installed by the phone company that connects your home’s
electrical wiring to your telephone network. It’s a gray box that is usually mounted on the
outside of your house. When you’re ready to install your new jack, it’s important to
disconnect your phone line so you aren’t working with a live wire. The electrical current that
runs through phone lines is not strong, but it could still give you a small shock if you aren’t
careful.
The NID has two sides: one for the phone company, and one for customers. Open
the side that’s intended for customers (the phone company’s side is usually
locked) and unplug the test jack. Now your phone line is disconnected from the
outside network.
If you’re working with an older interface box without a test jack, disconnect your
phone line by detatching the wires, making sure to remember which wire goes
where so you’ll be able to reattach them when your job is complete.
12/12/13 3 Ways to Install a Residential Telephone Jack - wikiHow
www.wikihow.com/Install-a-Residential-Telephone-Jack 4/13
1
2
Remove the old jack from the wall. Use a screwdriver to unscrew the old jack,
whether it’s a wall mount or a flush jack. Carefully pull the casing away from the wall,
and you will find that the jack is attached to your home’s wiring with wires of four different
colors: red, green, yellow, and black. Each wire is secured behind a screw. Use a
screwdriver to loosen the screws, unsecure the four wires from behind them, and pull the old
jack from the wall.
If your jack is the type that is a rectangular box attached to a plate on the wall with
notches, use a flathead screwdriver to pop off the top part of the case, and
proceed to loosen the screws and unsecure the wires. Unscrew the plating and
remove this from the wall as well.
Prepare the wires for your new jack. If you’re replacing a jack that has been
around for a long time, the four wires might need to be trimmed and stripped before
you attach them to the new jack. If the exposed parts of the wires look old or brittle, use a
wire cutter to trim off the damaged portions, no more than about ½” to ¾” (1.25 to 2 cm).
Part 2 of 3: Replace an Old Jack With a New One
12/12/13 3 Ways to Install a Residential Telephone Jack - wikiHow
www.wikihow.com/Install-a-Residential-Telephone-Jack 5/13
3
4
Now use the wire cutter or a utility knife to gently strip the insulation from the tips of the wires
so they may be connected to the new jack.
Attach the telephone wires to the new jack. Turn the new jack over and loosen the
four screws on the back. Connect each wire to the correct section of the jack, marked
by color; there will be a spot for the red, green, yellow, and black wires. Secure the wires by
tightening each screw.
Mount the jack. Push the wires into the wall and position the jack over the hole. Line
the jack’s screw holes with the holes made by the old jack. Place the new screws in
the screw holes and use a screwdriver to secure the new jack to the wall. Depending on the
type of jack you have, you may have a cover case that should be secured onto the wall
piece to complete the process.
Some types of jacks come with adhesive backing in addition to screws. You may
use this to secure the jack to the wall, but it isn’t strictly necessary.
12/12/13 3 Ways to Install a Residential Telephone Jack - wikiHow
www.wikihow.com/Install-a-Residential-Telephone-Jack 6/13
5
6
Reconnect the phone line. Return to the NID on the outside of your house. Open the
box and plug the test jack back in. If your NID doesn’t have a test plug, reconnect the
wires you previously disconnected, making sure to screw them in securely.
Test your line. Plug your telephone or DSL cable into your newly installed jack. Your
phone should have a dial tone, and your internet connection should work now (as long
as your computer is correctly set up for a DSL connection.
If the phone line does not seem to be working, you may need to unscrew the new
jack and make sure the wires are connected to the proper places and correctly
screwed in. If further electrical work is required, make sure to go back to the NID
and disconnect the phone line again before manipulating the wires.
12/12/13 3 Ways to Install a Residential Telephone Jack - wikiHow
www.wikihow.com/Install-a-Residential-Telephone-Jack 7/13
1
2
Choose a spot for the new phone jack. Keep in mind that you’ll be running phone
wires from the old phone jack to the new spot you choose.
Assess your room and think about the best path for the phone wires. If you need a
new phone jack on the opposite side of the room from your existing jack, will it be
possible to run the wires along your baseboards? You’ll want to keep your wires
neat, so have a plan in mind when you make your choice.
If you want to install a new wall mounted phone, it’s best to choose a spot a few
feet above your existing phone jack. This way, you won’t have to run unsightly wires
across your room.
Figure out how much new wire you need. Measure the distance from the old jack
to the spot where the new one will be installed. Include the entire path that the
telephone wire will travel: the distance from the old jack to the baseboard, around the
perimeter of the room, and from the baseboard to the new jack’s location. Go to the
hardware store and purchase the amount of wire you will need. If your new jack is going to
Part 3 of 3: Install a New Jack in a Different Part of the Room
12/12/13 3 Ways to Install a Residential Telephone Jack - wikiHow
www.wikihow.com/Install-a-Residential-Telephone-Jack 8/13
3
4
be located several feet from the old one, you should also buy fasteners that are made for
keeping the wire in place along walls and baseboards.
Choose a new jack. Baseboard jacks or wall jacks that house the phone wires in a
small box, rather than inside the wall, are the easiest phone jacks to install when
you’re looking for a jack for a new location. These types of jacks are simply affixed to your
baseboard or wall, with minimal drilling required.
Affix the new jack to the spot you have chosen. After you’ve gone outside to your
NID and disconnected your phone line in preparation for your task, it’s time to begin
the installation of your new jack. Some jacks come with adhesive backing and simple
mounting instructions. Others may need to be screwed into the wall. Depending on the type
of wall you have, this may be accomplished either with a screwdriver and a bit of muscle or
with a small drill.
Ensure that your jack is not installed at a crooked angle by using a level to help you
line up the jack with your floor or baseboard. Make small pencil marks in the
places where you’ll be screwing or drilling holes.
12/12/13 3 Ways to Install a Residential Telephone Jack - wikiHow
www.wikihow.com/Install-a-Residential-Telephone-Jack 9/13
5
6
Attach telephone wire to the old jack. Open the casing, or unscrew the plating, on
the old jack. Loosen the screws that secure the red, green, yellow and black
telephone wires. As necessary, trim damage from the old wires and strip the insulation from
the tips. Strip the insulation from the tips of the new wires, too. Twist the tips of the new
wires with the tips of the old wires according to color: red to red, green to green, yellow to
yellow, and black to black. Replace the twisted portions of the wires under the screws in the
jack, and tighten the screws. Thread the new wire through the hole in the phone jack casing,
and screw the casing back to the wall.
If the hole in the phone jack casing is too small, or if it’s difficult to thread the wires
through, it may be necessary to drill or cut a larger hole for this step.
Run the wire from the old jack to the new jack. Using the path you mapped out in
your original plan, run the new wire to the new jack. If you are running the wire along
baseboards or up walls, use the fasteners you bought at the hardware store to secure it
neatly in place.
12/12/13 3 Ways to Install a Residential Telephone Jack - wikiHow
www.wikihow.com/Install-a-Residential-Telephone-Jack 10/13
7
8
Attach telephone wire to the new jack. After you’ve run the wire from the old jack
to the new jack, trim the excess wire so that you have a manageable coil. Strip the
insulation from the tips of the four wires. Loosen the screws on the back of the new jack,
and affix the red, green, yellow, and black wires in their correct color-coded places. Tighten
the screws.
Finish installing the new jack. If you’re using an external jack, there will be space
inside the jack to coil the remaining wire. Place the cover on the jack and screw it on.
12/12/13 3 Ways to Install a Residential Telephone Jack - wikiHow
www.wikihow.com/Install-a-Residential-Telephone-Jack 11/13
9
10
Reconnect the phone line and test your work. Return to the NID box and
reconnect your phone line. Go back inside and test it by plugging in your phone or
DSL cable. If you have a dial tone and your internet works, your task is complete.
Finished.
Name your method
Know another method for How to Install a Residential Telephone Jack? Add it here...
12/12/13 3 Ways to Install a Residential Telephone Jack - wikiHow
www.wikihow.com/Install-a-Residential-Telephone-Jack 12/13
Add Method
Add your steps using an ordered list. For example:1. Step one2. Step two3. Step three
If you'd prefer not to run wires along your baseboards or walls, consider
threading them through your walls, instead.
A standard residential telephone line coming into your home has very
little voltage. However, if your phone were to ring while you were working
on a connected wire, the voltage would increase and could be
dangerous. Take the precaution of disconnecting your phone line before
doing electrical work.
A phone jack
A good set of wire cutters (wire snips or diagonal pliers)
A Phillips and flathead screwdriver
New telephone wire
Wire fasteners
A drill
How to
Connect PhoneJacks
How to
Do CommonElectrical Repairs
How to
Detect CrossLines Between 2or More ElectricalCircuits
How to
Wire a 3 WayLight Switch
Tips
Warnings
Things You'll Need
Related wikiHows
12/12/13 3 Ways to Install a Residential Telephone Jack - wikiHow
www.wikihow.com/Install-a-Residential-Telephone-Jack 13/13
How to
Replace aDefectiveElectrical Switchor Outlet
Thanks to all authors for creating a page that has been read 213,062 times.
Categories: Home Improvements and Repairs
Recent edits by: TJean, Teresa, JKL1234҉
Article Info