3-phase Motor - RS Components...
Transcript of 3-phase Motor - RS Components...
3-phase Motor
• Motor Overview• Model list• Product information for each model• Gear head combination dimensions• Round shaft motor dimensions
ContentsB-126B-128B-130B-162B-164
B-126
Outline of 3-phase motor
Features
• The 3-phase motor is an induction motor for 3-phase power.• Continuous time rating• The motor with national specifications is of heatproof class 120 (E); the motor with specifications compliant with
overseas standards is of heatproof class 130 (B).
Construction
Characteristics
• Speed-torque characteristics
StatorArmature
Shaft Winding
Frame
Bracket
Ball bearing
Oil sealWave washer
Ball bearing
Example:M8MX25G4Y
Speed (min–1)
0
1.0
0.8
0.6
0.4
0.2
1800
Torq
ue (
N·m
)
15001000500
50Hz 220V50Hz200V
60Hz 220V
60Hz 200V
System configuration diagram
Coding system
Brake unit (sold separately)Used when stopping the motor instantaneously C-45
Gear head (sold separately)
Motor
ACpower supply
Mounting hardware (option) D-2
Decimal gear head (sold separately)Used when a high reduction ratio is needed B-384
M 9 M X 40 G 4 Y S A
8 : 80 mm sq. (3.15 inch sq.)9 : 90 mm sq. (3.54 inch sq.)
G: Pinion shaftS : Round shaft
X : 40 W or smallerZ : 60 W or larger
K : Sealed connector
Y : National specifications: 200/220 V Specifications compliant with overseas standards: 200/220/230 V
C : 380/400 V
M : 3-phase motor 25 : 25 W40 : 40 W60 : 60 W90 : 90 W
4 : 4 poles
Size Motortype
Outputtype
Output Shapeof shaft
Option No. ofpoles
Voltage Classification
G: Specifications compliant with overseas standards
S : Round shaft (S for round shaft with national specifications only)
Left aligned when(no option is used )
Correspondingmodel number
Shape ofshaft Classification
Specifications compliantwith overseas standardsPinion shaftSpecifications compliant withoverseas standardsRound shaftNational specificationsPinion shaft
National specificationsRound shaft
42 mm sq. round shaftspecifications
G
S
G
S
S
G
G
–
S
–
The models with a motor modelnumber to which “A” is suffixedare not sold or available in Japan.
Fit tolerance symbol is used in the outside dimension diagram of motor and gear head. For further information, see “Fit tolerance” on page A-33.
Fit tolerance
B-127
B-128 B-129
Model list of 3-phase motor
80 mm sq.(3.15 inch sq.)
90 mm sq.(3.54 inch sq.)
25
40
60
90
*Refer to page B-444 for dimensions and permissible torque of high torque gear head.Refer to page B-446 for dimensions and permissible torque of right-angle gear head.Refer to page B-451 for dimensions and permissible torque of gear head -Inch (U.S.A.).Refer to page B-448 for dimensions of decimal gear head.
M8MX25G4Y
M8MX25G4YG(A)
M9MX40G4Y
M9MX40G4YG(A)
M9MZ60G4Y
M9MZ60G4YG(A)
M9MZ90G4Y
M9MZ90G4YG(A)
200/220V
200/220/230V
200/220V
200/220/230V
200/220V
200/220/230V
200/220V
200/220/230V
B-130
B-132
B-134
B-136
B-138
B-140
B-142
B-144
M8MX25GK4Y
M8MX25GK4YG(A)
M8MX25GK4CG(A)
M9MX40GK4Y
M9MX40GK4YG(A)
M9MX40GK4CG(A)
M9MZ60GK4Y
M9MZ60GK4YG(A)
M9MZ60GK4CG(A)
M9MZ90GK4Y
M9MZ90GK4YG(A)
M9MZ90GK4CG(A)
B-146
B-148
B-148
B-150
B-152
B-152
B-154
B-156
B-156
B-158
B-160
B-160
MX8G B
MX9G B
MZ9G B
MY9G B
MX8G M
MX9G M
–
–
–
MR9G B
MP9G B
–
MX9G R
MZ9G
R
MX8G10XB
MX9G10XB
MZ9G10XB
80 mm sq.(3.15 inch sq.)
90 mm sq.(3.54 inch sq.)
25
40
60
90
M8MX25S4YS
M8MX25S4YG(A)
M9MX40S4YS
M9MX40S4YG(A)
M9MZ60S4YS
M9MZ60S4YG(A)
M9MZ90S4YS
M9MZ90S4YG(A)
200/220V
200/220/230V
200/220V
200/220/230V
200/220V
200/220/230V
200/220V
200/220/230V
M8MX25SK4YS
M8MX25SK4YG(A)
M8MX25SK4CG(A)
M9MX40SK4YS
M9MX40SK4YG(A)
M9MX40SK4CG(A)
M9MZ60SK4YS
M9MZ60SK4YG(A)
M9MZ60SK4CG(A)
M9MZ90SK4YS
M9MZ90SK4YG(A)
M9MZ90SK4CG(A)
200/220V
200/220/230V
380/400V
200/220V
200/220/230V
380/400V
200/220V
200/220/230V
380/400V
200/220V
200/220/230V
380/400V
200/220V
200/220/230V
380/400V
200/220V
200/220/230V
380/400V
200/220V
200/220/230V
380/400V
200/220V
200/220/230V
380/400V
Output(W)
SizeLeadwire typeModel number Specifications Page
Sealed connector typeModel number Specifications Page
Motor compliant with overseas standards Hinge attachedStandard gear head
Ball bearing metal bearingDecimal
gear headHigh torquegear head
Right-anglegear head
MX9G BU
MX9G BU
MZ9G
BU
Gear head -Inch(U.S.A.)
Output(W)
SizeLeadwire typeModel number
Sealed connector typeModel number
Motor compliant with overseas standardsElectrical Appliance and Material Safety Law
Specifications Specifications
* The specifications and wire connections of the round shaft motor are the same as those of the pinion shaft motor. Dimensional outline drawing Page B-164.
<Notice>380V/400V 3-phase round shaft motors with a sealed connector are not covered by the Electrical Appliance and Material SafetyLaw.
Applicable gear headPinion shaft motor
Round shaft motor
96.3(3.79)
85(3.35) 11.3(0.44)7(0.28) 2(0.08)
ø75
h7
80 mm sq.
4–ø5.5(ø0.22)
CWCCW
3 motor leadwires 300±30 mm (11.8±1.18 inch)AWG20
O-ring
ø94(ø3.70)
MA
Xø
86(ø
3.39
)
(3.15 inch sq.)
(ø2.
95h7
)
Change any two lead wires of R, S and T for CW rotation.
R
S
T
White
Gray
Black
CCW(counterclockwise)
3-phase motor (leadwire)
80 mmsq. M8MX25G4Y
0.54 (76.5)
0.40 (56.6)
0.66 (93.5)
0.50 (70.8)
0.18 (25.5)
0.15 (21.2)
0.18 (25.5)
0.15 (21.2)
4 25
200
220
50
60
50
60
50
47
54
49
0.25
0.22
0.27
0.23
1350
1625
1375
1650
0.62
0.58
0.67
0.64
Cont.
Cont.
Motor model No.
Rating
SizeNumber
of pole
(P)
Output
(W)
Voltage
(V)
Frequency
(Hz)
Rating
(min)Input
(W)
Current
(A)
TorqueN·m
(oz-in)
Starting torque
N·m
(oz-in)
Starting
current
(A)Speed
(min–1)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
6002.53
5003
3.6
2506
7.2
30056
3604.25
2007.59
7502
2.4
9001.72
10001.51.8
12001.31.5
15001
1.2
18000.81
0.39(3.45)
0.47(4.16)
0.66(5.84)
0.78(6.90)
0.98(8.67)
1.18(10.4)
1.27(11.2)
1.57(13.9)
1.96(17.3)
2.35(20.8)
2.55(22.6)
3.14(27.8)
3.82(33.8)
4.61(40.8)
6.37(56.4)
7.64(67.6)
7.84(69.4)
0.32(2.83)
0.39(3.45)
0.55(4.87)
0.66(5.84)
0.81(7.17)
0.98(8.67)
1.08(9.56)
1.27(11.2)
1.57(13.9)
1.96(17.3)
2.06(18.2)
2.65(23.5)
3.14(27.8)
3.82(33.8)
5.29(46.8)
6.37(56.4)
7.84(69.4)
3
500
600
3.6
416.7
500
5
300
360
6
250
300
7.5
200
240
9
166.7
200
10
150
180
12.5
120
144
15
100
120
18
83.3
100
20
75
90
25
60
72
30
50
60
36
41.7
50
50
30
36
60
25
30
75
20
24
90
16.7
20
100
15
18
120
12.5
15
150
10
12
180
8.3
10
• Permissible torque at output shaft of gear head using decimal gear head
MX8G10XBSame as motor
rotational direction Reverse to motor rotational direction
MX8G B(ball bearing)MX8G M
(metal bearing)
Same as motor rotational direction Reverse to motor rotational direction
Applicable gear head
Bearing Decimalgear head
Speed(min–1)
Permissibletorque
50Hz60Hz
N·m(lb-in)
Rotational direction
Reduction ratio
50Hz60Hz
50Hz
60Hz
Reduction ratio
Rotational direction
Speed (min–1)
Unit of permissible torque: upper (N·m) / lower (lb-in)
MX8G3B toMX8G180B(ball bearing)MX8G3M toMX8G180M(metal bearing)
Applicable gear head
Connection diagram Speed-torque characteristics
00 1800
1.0
0.8
0.6
0.4
0.2
15001000500
60Hz 200V60Hz 220V
50Hz 200V50Hz 220V
(N·m)
Speed (min–1)
Tor
que
(oz-in)
100
50
M8MX25G4Y
M8MX25G4Y 4P 25 W 200 V / 220 V
* Please read your User's manual carefully so that you will understand the operation and safety precautions before attempting to operate the system. (Note) Because the dimensions may be subject to change, also check the determinate dimensions if the gear head is to be used for design.
B-130 B-131
• Specifications
• Permissible torque at output shaft of gear head* The speed shown below is a calculated value based on the synchronous rotational speed. Depending on the load, the speed is less than the indicated value by 2 to 20%.
• The specifications and wire connections of the round shaft motor are the same as those of the pinion shaft type. For the dimensional outline drawing, refer to page B-164.
* Diameter of applicable cabtyre cable to be ø8(ø0.31) to ø12(ø0.47).
Helical
gear
Module
0.5Numberof teeth
9
Mass1.5 kg3.31 lb
Model list B-128Coding system B-127System configuration B-127Features B-126
Ind
uctio
nm
oto
rR
eversible
mo
tor
3-ph
asem
oto
rE
lectrom
agn
eticb
rakem
oto
rV
ariable
speed
ind
uctio
nm
oto
rV
ariable
speed
reversible
mo
tor
Variable
speedelectrom
agneticbrake
single-phasem
otorV
ariable
speed
un
itm
oto
rC
&B
mo
tor
2-poleround
shaftm
oto
rG
earh
eadG
earh
ead-in
ch(U
.S.A
.)80mm (3.15inch) sq. 25 W
Motor (dimensions) Scale: 1/3, Unit: mm (inch)
Gear head combination B-162 Round shaft motor B-164 Decimal gear head B-448 Gear head -inch (U.S.A.) B-449 Controls C-4 Option D-2
ø10
h7ø
30(ø
1.18
)(ø
0.39
h7)
7.5(
0.30
)15
(0.5
9)
4(0.16)
80 mm sq.(3.15 inch sq.)
ø94(ø3.70)
4–ø5.5(ø0.22)
30(1.18) 32(1.26)25
(0.98)6(0.24)
Gear head (dimensions) Scale: 1/3, Unit: mm (inch)
MX8G B (ball bearing) / MX8G M (metal bearing) Mass 0.6 kg (1.32 lb)
Key and keyway(dimensions) [attachment]
25(0.98)
4 0 -0.
030
7.5 0
-
0.15
4 0
-0.030
0.16 0
-0.001
4+0.060
+0.010
( )
0.16
0
-
0.00
1(
)
0.16+0.002
+0.0004( )
0.3 0
-
0.00
6(
)
MX8G B(M)
(Refer to page A-58 for connection of thermal protector.)
CCW(counterclockwise)
R
S
T
White
Gray
Black
Blue
Blue TPThermal protector
Change any two lead wires of R, S and T for CW rotation.
3-phase motor (leadwire)
80 mmsq.
M8MX25G4YGM8MX25G4YGA
0.54 (76.5)
0.40 (56.6)
0.50 (70.8)
0.54 (76.5)
0.18 (25.5)
0.15 (21.2)
0.14 (19.8)
0.14 (19.8)
4 25
50
60
60
60
200
220
230
50
47
49
50
0.25
0.22
0.23
0.24
1350
1625
1650
1675
0.62
0.58
0.64
0.65
Cont.
Motor model No.
Rating
SizeNumber
of pole
(P)
Output
(W)
Voltage
(V)
Frequency
(Hz)
Rating
(min)Input
(W)
Current
(A)
TorqueN·m
(oz-in)
Starting torque
N·m
(oz-in)
Starting
current
(A)Speed
(min–1)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
6002.53
5003
3.6
2506
7.2
30056
3604.25
2007.59
7502
2.4
9001.72
10001.51.8
12001.31.5
15001
1.2
18000.81
0.39(3.45)
0.47(4.16)
0.66(5.84)
0.78(6.90)
0.98(8.67)
1.18(10.4)
1.27(11.2)
1.57(13.9)
1.96(17.3)
2.35(20.8)
2.55(22.6)
3.14(27.8)
3.82(33.8)
4.61(40.8)
6.37(56.4)
7.64(67.6)
7.84(69.4)
0.32(2.83)
0.39(3.45)
0.55(4.87)
0.66(5.84)
0.81(7.17)
0.98(8.67)
1.08(9.56)
1.27(11.2)
1.57(13.9)
1.96(17.3)
2.06(18.2)
2.65(23.5)
3.14(27.8)
3.82(33.8)
5.29(46.8)
6.37(56.4)
7.84(69.4)
3
500
600
3.6
416.7
500
5
300
360
6
250
300
7.5
200
240
9
166.7
200
10
150
180
12.5
120
144
15
100
120
18
83.3
100
20
75
90
25
60
72
30
50
60
36
41.7
50
50
30
36
60
25
30
75
20
24
90
16.7
20
100
15
18
120
12.5
15
150
10
12
180
8.3
10
• Permissible torque at output shaft of gear head using decimal gear head
MX8G10XBSame as motor
rotational direction Reverse to motor rotational direction
MX8G B(ball bearing)MX8G M
(metal bearing)
Same as motor rotational direction Reverse to motor rotational direction
Applicable gear head
Bearing Decimalgear head
Speed(min–1)
Permissibletorque
50Hz60Hz
N·m(lb-in)
Rotational direction
Reduction ratio
50Hz60Hz
50Hz
60Hz
Reduction ratio
Rotational direction
Speed (min–1)
Unit of permissible torque: upper (N·m) / lower (lb-in)
MX8G3B toMX8G180B(ball bearing)MX8G3M toMX8G180M(metal bearing)
Applicable gear head
Connection diagram Speed-torque characteristics
60Hz 200V
50Hz 200V
00 1800
1.0
0.8
0.6
0.4
0.2
15001000500
(N·m)
Speed (min–1)
Tor
que
(oz-in)
100
50
M8MX25G4YG(A)
* Please read your User's manual carefully so that you will understand the operation and safety precautions before attempting to operate the system.
B-132
• Specifications
• Permissible torque at output shaft of gear head* The speed shown below is a calculated value based on the synchronous rotational speed. Depending on the load, the speed is less than the indicated value by 2 to 20%.
• The specifications and wire connections of the round shaft motor are the same as those of the pinion shaft type. For the dimensional outline drawing, refer to page B-164.
Model list B-128Coding system B-127System configuration B-127Features B-126
• The models with a motor model number to which “A” is suffixed are not sold or available in Japan.
96.3(3.79)
85(3.35) 11.3(0.44)7(0.28) 2(0.08)
ø75
h7
80 mm sq.
4–ø5.5(ø0.22)
CWCCW
5 motor leadwires 300±30 mm (11.8±1.18 inch)AWG20
O-ring
ø94(ø3.70)
MA
Xø
86(ø
3.39
)
(3.15 inch sq.)
(ø2.
95h7
)
M8MX25G4YG(A) 4P 25 W 200 V / 220 V / 230 V
(Note) Because the dimensions may be subject to change, also check the determinate dimensions if the gear head is to be used for design.
B-133
Helical
gear
Module
0.5Numberof teeth
9
Mass1.5 kg3.31 lb
Ind
uctio
nm
oto
rR
eversible
mo
tor
3-ph
asem
oto
rE
lectrom
agn
eticb
rakem
oto
rV
ariable
speed
ind
uctio
nm
oto
rV
ariable
speed
reversible
mo
tor
Variable
speedelectrom
agneticbrake
single-phasem
otorV
ariable
speed
un
itm
oto
rC
&B
mo
tor
2-poleround
shaftm
oto
rG
earh
eadG
earh
ead-in
ch(U
.S.A
.)80mm (3.15inch) sq. 25 W
Motor (dimensions) Scale: 1/3, Unit: mm (inch)
Gear head combination B-162 Round shaft motor B-164 Decimal gear head B-448 Gear head -inch (U.S.A.) B-449 Controls C-4 Option D-2
ø10
h7ø
30(ø
1.18
)(ø
0.39
h7)
7.5(
0.30
)15
(0.5
9)
4(0.16)
80 mm sq.(3.15 inch sq.)
ø94(ø3.70)
4–ø5.5(ø0.22)
30(1.18) 32(1.26)25
(0.98)6(0.24)
Gear head (dimensions) Scale: 1/3, Unit: mm (inch)
MX8G B (ball bearing) / MX8G M (metal bearing) Mass 0.6 kg (1.32 lb)
Key and keyway(dimensions) [attachment]
25(0.98)
4 0 -0.
030
7.5 0
-
0.15
4 0
-0.030
0.16 0
-0.001
4+0.060
+0.010
( )
0.16
0
-
0.00
1(
)
0.16+0.002
+0.0004( )
0.3 0
-
0.00
6(
)
MX8G B(M)
117.8(4.64)
105(4.13) 12.8(0.50)7.5(0.30) 2(0.08)
ø85
h7
90 mm sq.
4–ø6.5(ø0.26)
CWCCW
3 motor leadwires 300±30 mm (11.8±1.18 inch)AWG20
ø104(ø4.09)
MA
Xø
95(ø
3.74
)
O-ring
(3.54 inch sq.)
(ø3.
35h7
)
Change any two lead wires of R, S and T for CW rotation.
R
S
T
White
Gray
Black
CCW(counterclockwise)
3-phase motor (leadwire)
90 mmsq. M9MX40G4Y
0.72 (102)
0.51 (72.2)
0.88 (125)
0.63 (89.2)
0.28 (39.7)
0.24 (34.0)
0.27 (38.2)
0.23 (32.6)
4 40
200
220
50
60
50
60
69
68
70
66
0.31
0.29
0.32
0.28
1350
1625
1375
1675
0.90
0.82
1.0
0.91
Cont.
Cont.
Motor model No.
Rating
SizeNumber
of pole
(P)
Output
(W)
Voltage
(V)
Frequency
(Hz)
Rating
(min)Input
(W)
Current
(A)
TorqueN·m
(oz-in)
Starting torque
N·m
(oz-in)
Starting
current
(A)Speed
(min–1)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
6002.53
5003
3.6
2506
7.2
30056
3604.25
2007.59
7502
2.4
9001.72
10001.51.8
12001.31.5
15001
1.2
18000.81
0.66(5.84)
0.78(6.90)
1.08(9.56)
1.27(11.2)
1.57(13.9)
1.86(16.5)
2.25(19.9)
2.74(24.3)
3.23(28.6)
3.92(34.7)
4.41(39.0)
5.29(46.8)
6.37(56.4)
7.94(70.3)
9.80(86.7)
9.80(86.7)
0.55(4.87)
0.66(5.84)
0.90(7.97)
1.08(9.56)
1.27(11.2)
1.57(13.9)
1.76(15.6)
2.25(19.9)
2.74(24.3)
3.23(28.6)
3.53(31.2)
4.41(39.0)
5.29(46.8)
6.37(56.4)
8.82(78.1)
9.80(86.7)
3
500
600
3.6
416.7
500
5
300
360
6
250
300
7.5
200
240
9
166.7
200
10
150
180
12.5
120
144
15
100
120
18
83.3
100
20
75
90
25
60
72
30
50
60
36
41.7
50
50
30
36
60
25
30
75
20
24
90
16.7
20
100
15
18
120
12.5
15
150
10
12
180
8.3
10
• Permissible torque at output shaft of gear head using decimal gear head
MX9G10XBSame as motor
rotational direction Reverse to motor rotational direction
MX9G B(ball bearing)MX9G M
(metal bearing)
Same as motor rotational direction Reverse to motor rotational direction
Applicable gear head
Bearing Decimalgear head
Speed(min–1)
Permissibletorque
50Hz60Hz
N·m(lb-in)
Rotational direction
Reduction ratio
50Hz60Hz
50Hz
60Hz
Reduction ratio
Rotational direction
Speed (min–1)
Unit of permissible torque: upper (N·m) / lower (lb-in)
MX9G3B toMX9G180B(ball bearing)MX9G3M toMX9G180M(metal bearing)
Applicable gear head
Connection diagram Speed-torque characteristics
00 1800
1.0
0.8
0.6
0.4
0.2
15001000500
60Hz 200V60Hz 220V
50Hz 200V50Hz 220V
(N·m)
Speed (min–1)
Tor
que
(oz-in)
100
50
M9MX40G4Y
M9MX40G4Y 4P 40 W 200 V / 220 V
* Please read your User's manual carefully so that you will understand the operation and safety precautions before attempting to operate the system. (Note) Because the dimensions may be subject to change, also check the determinate dimensions if the gear head is to be used for design.
B-134 B-135
• Specifications
• Permissible torque at output shaft of gear head* The speed shown below is a calculated value based on the synchronous rotational speed. Depending on the load, the speed is less than the indicated value by 2 to 20%.
• The specifications and wire connections of the round shaft motor are the same as those of the pinion shaft type. For the dimensional outline drawing, refer to page B-164.
* Diameter of applicable cabtyre cable to be ø8(ø0.31) to ø12(ø0.47).
Helical
gear
Module
0.55Numberof teeth
9
Mass2.4 kg5.29 lb
Model list B-128Coding system B-127System configuration B-127Features B-126
Ind
uctio
nm
oto
rR
eversible
mo
tor
3-ph
asem
oto
rE
lectrom
agn
eticb
rakem
oto
rV
ariable
speed
ind
uctio
nm
oto
rV
ariable
speed
reversible
mo
tor
Variable
speedelectrom
agneticbrake
single-phasem
otorV
ariable
speed
un
itm
oto
rC
&B
mo
tor
2-poleround
shaftm
oto
rG
earh
eadG
earh
ead-in
ch(U
.S.A
.)90mm (3.54inch) sq. 40 W
Motor (dimensions) Scale: 1/3, Unit: mm (inch)
Gear head combination B-162 Round shaft motor B-164 Decimal gear head B-448 Gear head -inch (U.S.A.) B-449 Controls C-4 Option D-2
ø12
h7(ø
0.47
)
ø36
(ø1.
42) 9.
5(0.
37)
18(0
.71)
4(0.16)
90 mm sq.(3.54 inch sq.)
ø104(ø4.09)
4–ø7(ø0.28)
37(1.46) 32(1.26)
25(0.98)
5(0.20)
Gear head (dimensions) Scale: 1/3, Unit: mm (inch)
MX9G B (ball bearing) / MX9G M (metal bearing) Mass 0.8 kg (1.76 lb)
Key and keyway(dimensions) [attachment]
25(0.98)
4 0 -0.
030
9.5 0
-
0.15
4 0
-0.030
0.16 0
-0.001
4+0.060
+0.010
( )
0.16
0
-
0.00
1(
)
0.16+0.002
+0.0004( )
0.37
0
-0
.006
(
)
MX9G B(M)
(Refer to page A-58 for connection of thermal protector.)
CCW(counterclockwise)
R
S
T
White
Gray
Black
Blue
Blue TPThermal protector
Change any two lead wires of R, S and T for CW rotation.
3-phase motor (leadwire)
90 mmsq.
M9MX40G4YGM9MX40G4YGA
0.72 (102)
0.51 (72.2)
0.63 (89.2)
0.69 (97.7)
0.28 (39.7)
0.24 (34.0)
0.23 (32.6)
0.23 (32.6)
4 40
50
60
60
60
200
220
230
69
68
66
66
0.31
0.29
0.28
0.29
1350
1625
1675
1675
0.90
0.82
0.91
0.96
Cont.
Motor model No.
Rating
SizeNumber
of pole
(P)
Output
(W)
Voltage
(V)
Frequency
(Hz)
Rating
(min)Input
(W)
Current
(A)
TorqueN·m
(oz-in)
Starting torque
N·m
(oz-in)
Starting
current
(A)Speed
(min–1)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
6002.53
5003
3.6
2506
7.2
30056
3604.25
2007.59
7502
2.4
9001.72
10001.51.8
12001.31.5
15001
1.2
18000.81
0.66(5.84)
0.78(6.90)
1.08(9.56)
1.27(11.2)
1.57(13.9)
1.86(16.5)
2.25(19.9)
2.74(24.3)
3.23(28.6)
3.92(34.7)
4.41(39.0)
5.29(46.8)
6.37(56.4)
7.94(70.3)
9.80(86.7)
9.80(86.7)
0.55(4.87)
0.66(5.84)
0.90(7.97)
1.08(9.56)
1.27(11.2)
1.57(13.9)
1.76(15.6)
2.25(19.9)
2.74(24.3)
3.23(28.6)
3.53(31.2)
4.41(39.0)
5.29(46.8)
6.37(56.4)
8.82(78.1)
9.80(86.7)
3
500
600
3.6
416.7
500
5
300
360
6
250
300
7.5
200
240
9
166.7
200
10
150
180
12.5
120
144
15
100
120
18
83.3
100
20
75
90
25
60
72
30
50
60
36
41.7
50
50
30
36
60
25
30
75
20
24
90
16.7
20
100
15
18
120
12.5
15
150
10
12
180
8.3
10
• Permissible torque at output shaft of gear head using decimal gear head
MX9G10XBSame as motor
rotational direction Reverse to motor rotational direction
MX9G B(ball bearing)MX9G M
(metal bearing)
Same as motor rotational direction Reverse to motor rotational direction
Applicable gear head
Bearing Decimalgear head
Speed(min–1)
Permissibletorque
50Hz60Hz
N·m(lb-in)
Rotational direction
Reduction ratio
50Hz60Hz
50Hz
60Hz
Reduction ratio
Rotational direction
Speed (min–1)
Unit of permissible torque: upper (N·m) / lower (lb-in)
MX9G3B toMX9G180B(ball bearing)MX9G3M toMX9G180M(metal bearing)
Applicable gear head
Connection diagram Speed-torque characteristics
00 1800
1.0
0.8
0.6
0.4
0.2
15001000500
200V 60Hz
200V 50Hz
(N·m)
Speed (min–1)
Tor
que
(oz-in)
100
50
M9MX40G4YG(A)
* Please read your User's manual carefully so that you will understand the operation and safety precautions before attempting to operate the system.
B-136
• Specifications
• Permissible torque at output shaft of gear head* The speed shown below is a calculated value based on the synchronous rotational speed. Depending on the load, the speed is less than the indicated value by 2 to 20%.
• The specifications and wire connections of the round shaft motor are the same as those of the pinion shaft type. For the dimensional outline drawing, refer to page B-164.
Model list B-128Coding system B-127System configuration B-127Features B-126
• The models with a motor model number to which “A” is suffixed are not sold or available in Japan.
117.8(4.64)
105(4.13) 12.8(0.50)7.5(0.30) 2(0.08)
ø85
h7
90 mm sq.
4–ø6.5(ø0.26)
CWCCW
5 motor leadwires 300±30 mm (11.8±1.18 inch)AWG20
ø104(ø4.09)
MA
Xø
95(ø
3.74
)
O-ring
(3.54 inch sq.)
(ø3.
35h7
)
M9MX40G4YG(A) 4P 40 W 200 V / 220 V / 230 V
(Note) Because the dimensions may be subject to change, also check the determinate dimensions if the gear head is to be used for design.
B-137
Helical
gear
Module
0.55Numberof teeth
9
Mass2.4 kg5.29 lb
Ind
uctio
nm
oto
rR
eversible
mo
tor
3-ph
asem
oto
rE
lectrom
agn
eticb
rakem
oto
rV
ariable
speed
ind
uctio
nm
oto
rV
ariable
speed
reversible
mo
tor
Variable
speedelectrom
agneticbrake
single-phasem
otorV
ariable
speed
un
itm
oto
rC
&B
mo
tor
2-poleround
shaftm
oto
rG
earh
eadG
earh
ead-in
ch(U
.S.A
.)90mm (3.54inch) sq. 40 W
Motor (dimensions) Scale: 1/3, Unit: mm (inch)
Gear head combination B-162 Round shaft motor B-164 Decimal gear head B-448 Gear head -inch (U.S.A.) B-449 Controls C-4 Option D-2
ø12
h7(ø
0.47
)
ø36
(ø1.
42) 9.
5(0.
37)
18(0
.71)
4(0.16)
90 mm sq.(3.54 inch sq.)
ø104(ø4.09)
4–ø7(ø0.28)
37(1.46) 32(1.26)
25(0.98)
5(0.20)
Gear head (dimensions) Scale: 1/3, Unit: mm (inch)
MX9G B (ball bearing) / MX9G M (metal bearing) Mass 0.8 kg (1.76 lb)
Key and keyway(dimensions) [attachment]
25(0.98)
4 0 -0.
030
9.5 0
-
0.15
4 0
-0.030
0.16 0
-0.001
4+0.060
+0.010
( )
0.16
0
-
0.00
1(
)
0.16+0.002
+0.0004( )
0.37
0
-0
.006
(
)
MX9G B(M)
140.5(5.53)
120(4.72) 20.5(0.81)7.5(0.30)40(1.57) 2(0.08)
ø85
h7
CWCCW
3 motor leadwires 300±30 mm (11.8±1.18 inch)AWG20
92 m
m s
q.(3
.62
inch
sq.
)
4–ø6.5(ø0.26)ø104(ø4.09)
90 mm sq.(3.54 inch sq.)
(ø3.
35h7
)
O-ring
Change any two lead wires of R, S and T for CW rotation.
R
S
T
White
Gray
Black
CCW(counterclockwise)
3-phase motor (leadwire)
90 mmsq. M9MZ60G4Y
1.0 (142)
0.69 (97.7)
1.2 (170)
0.87 (123)
0.42 (59.5)
0.35 (49.6)
0.41 (58.1)
0.34 (48.1)
4 60
200
220
50
60
50
60
101
96
103
98
0.45
0.41
0.46
0.40
1350
1625
1375
1650
1.3
1.2
1.5
1.3
Cont.
Cont.
Motor model No.
Rating
SizeNumber
of pole
(P)
Output
(W)
Voltage
(V)
Frequency
(Hz)
Rating
(min)Input
(W)
Current
(A)
TorqueN·m
(oz-in)
Starting torque
N·m
(oz-in)
Starting
current
(A)Speed
(min–1)
Same as motor rotational direction
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
6002.53
5003
3.6
2506
7.2
30056
3604.25
7502
2.4
9001.72
10001.51.8
12001.31.5
15001
1.2
18000.81
0.98(8.7)
1.18(10.4)
1.57(13.9)
1.96(17.3)
2.35(20.8)
2.94(26.0)
3.14(27.8)
3.92(34.7)
4.70(41.6)
5.59(49.5)
6.27(55.5)
7.55(66.8)
9.11(80.6)
11.0(97.4)
15.2(135)
17.8(158)
19.6(173)
0.78(6.9)
0.98(8.7)
1.37(12.1)
1.57(13.9)
1.96(17.3)
2.35(20.8)
2.65(23.5)
3.33(29.5)
3.92(34.7)
4.70(41.6)
5.29(46.8)
6.47(57.3)
7.55(66.8)
9.11(80.6)
12.6(112)
15.2(135)
19.6(173)
3
500
600
3.6
416.7
500
5
300
360
6
250
300
7.5
200
240
9
166.7
200
10
150
180
12.5
120
144
15
100
120
18
83.3
100
20
75
90
25
60
72
30
50
60
36
41.7
50
50
30
36
60
25
30
75
20
24
90
16.7
20
100
15
18
120
12.5
15
180
8.3
10
200
7.5
9
150
10
12
Same as motor rotational direction Same as motor rotational directionReverse to motor rotational direction
Reverse to motorrotational direction
• Permissible torque at output shaft of gear head using decimal gear head
MZ9G10XB
MZ9G B(ball bearing / Hinge not attached)
MY9G B(ball bearing / Hinge attached)
Applicable gear head
Bearing Decimalgear head
Speed(min–1)
Permissibletorque
50Hz60Hz
N·m(lb-in)
Rotational direction
Reduction ratio
50Hz60Hz
50Hz
60Hz
Reduction ratio
Rotational direction
Speed (min–1)
Unit of permissible torque: upper (N·m) / lower (lb-in)
MZ9G3B toMZ9G200B
MY9G3B toMY9G200B
Applicable gear head
ball bearing(hinge not attached)
ball bearing(hinge attached)
Connection diagram Speed-torque characteristics
00 1800
2.0
1.5
1.0
0.5
15001000500
50Hz 200V
50Hz 220V
60Hz 200V60Hz 220V
(N·m)
Speed (min–1)
Tor
que
(oz-in)
100
200
M9MZ60G4Y
M9MZ60G4Y 4P 60 W 200 V / 220 V (with fan)
* Please read your User's manual carefully so that you will understand the operation and safety precautions before attempting to operate the system. (Note) Because the dimensions may be subject to change, also check the determinate dimensions if the gear head is to be used for design.
B-138 B-139
• Specifications
• Permissible torque at output shaft of gear head* The speed shown below is a calculated value based on the synchronous rotational speed. Depending on the load, the speed is less than the indicated value by 2 to 20%.
• The specifications and wire connections of the round shaft motor are the same as those of the pinion shaft type. For the dimensional outline drawing, refer to page B-164.
* Diameter of applicable cabtyre cable to be ø8(ø0.31) to ø12(ø0.47).
Helical
gear
Module
0.6Numberof teeth
9
Mass2.7 kg5.95 lb
Model list B-128Coding system B-127System configuration B-127Features B-126
Ind
uctio
nm
oto
rR
eversible
mo
tor
3-ph
asem
oto
rE
lectrom
agn
eticb
rakem
oto
rV
ariable
speed
ind
uctio
nm
oto
rV
ariable
speed
reversible
mo
tor
Variable
speedelectrom
agneticbrake
single-phasem
otorV
ariable
speed
un
itm
oto
rC
&B
mo
tor
2-poleround
shaftm
oto
rG
earh
eadG
earh
ead-in
ch(U
.S.A
.)90mm (3.54inch) sq. 60 W
Motor (dimensions) Scale: 1/4, Unit: mm (inch)
Gear head combination B-162 Round shaft motor B-164 Decimal gear head B-448 Gear head -inch (U.S.A.) B-449 Controls C-4 Option D-2
Note) MZ / MY is available for a gear head of either type.
ø15
h7(ø
0.59
h7)
ø34
(ø1.
34) 12
(0.4
7)18
(0.7
1)
5(0.20)
90 mm sq.(3.54 inch sq.)
ø104(ø4.09)
4–ø7(ø0.28)
29(1.14)
25(0.98)
7(0.28)
60(2.36) 38(1.50)
5(0.
20)
ø34
(ø1.
34)
ø15
h7(ø
0.59
h7)
110(
4.33
)13
0(5.
12)
60(2.36)36(1.42)4–ø8.5
(ø0.33)
4–ø6.5(ø0.26)
60(2.36) 38(1.50)7(0.28)
29(1.14)
12(0.47)8(0.31)
25(0.98)
18(0.71)
12(0.47)
ø104
(ø4.09)
90 m
m s
q.(3
.54
inch
sq.
)
60(2
.36)
Gear head (dimensions) Scale: 1/4, Unit: mm (inch)
MZ9G B (ball bearing / hinge not attached) MY9G B (ball bearing / hinge attached)Mass 1.4 kg (3.09 lb) Mass 1.4 kg (3.09 lb)
Key and keyway(dimensions) [attachment]
25(0.98)
5 0 -0.
030
12 0
-0
.15
5 0
-0.030
0.20 0
-0.001
5+0.050
0
( )
0.20
0
-
0.00
1(
)
0.20+0.002
0( )
0.47
0
-0
.006
(
)
MZ9G BMY9G B
(Refer to page A-58 for connection of thermal protector.)
CCW(counterclockwise)
R
S
T
White
Gray
Black
Blue
Blue TPThermal protector
Change any two lead wires of R, S and T for CW rotation.
3-phase motor (leadwire)
90 mmsq.
M9MZ60G4YGM9MZ60G4YGA
1.0 (142)
0.69 (97.7)
0.87 (123)
1.0 (142)
0.42 (59.5)
0.35 (49.6)
0.35 (49.6)
0.34 (48.1)
4 60
50
60
60
60
200
220
230
101
96
98
98
0.45
0.41
0.40
0.41
1350
1625
1650
1675
1.3
1.2
1.3
1.4
Cont.
Motor model No.
Rating
SizeNumber
of pole
(P)
Output
(W)
Voltage
(V)
Frequency
(Hz)
Rating
(min)Input
(W)
Current
(A)
TorqueN·m
(oz-in)
Starting torque
N·m
(oz-in)
Starting
current
(A)Speed
(min–1)
Same as motor rotational direction
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
6002.53
5003
3.6
2506
7.2
30056
3604.25
7502
2.4
9001.72
10001.51.8
12001.31.5
15001
1.2
18000.81
0.98(8.7)
1.18(10.4)
1.57(13.9)
1.96(17.3)
2.35(20.8)
2.94(26.0)
3.14(27.8)
3.92(34.7)
4.70(41.6)
5.59(49.5)
6.27(55.5)
7.55(66.8)
9.11(80.6)
11.0(97.4)
15.2(135)
17.8(158)
19.6(173)
0.78(6.9)
0.98(8.7)
1.37(12.1)
1.57(13.9)
1.96(17.3)
2.35(20.8)
2.65(23.5)
3.33(29.5)
3.92(34.7)
4.70(41.6)
5.29(46.8)
6.47(57.3)
7.55(66.8)
9.11(80.6)
12.6(112)
15.2(135)
19.6(173)
3
500
600
3.6
416.7
500
5
300
360
6
250
300
7.5
200
240
9
166.7
200
10
150
180
12.5
120
144
15
100
120
18
83.3
100
20
75
90
25
60
72
30
50
60
36
41.7
50
50
30
36
60
25
30
75
20
24
90
16.7
20
100
15
18
120
12.5
15
180
8.3
10
200
7.5
9
150
10
12
Same as motor rotational direction Same as motor rotational directionReverse to motor rotational direction
Reverse to motorrotational direction
• Permissible torque at output shaft of gear head using decimal gear head
MZ9G10XB
MZ9G B(ball bearing / Hinge not attached)
MY9G B(ball bearing / Hinge attached)
Applicable gear head
Bearing Decimalgear head
Speed(min–1)
Permissibletorque
50Hz60Hz
N·m(lb-in)
Rotational direction
Reduction ratio
50Hz60Hz
50Hz
60Hz
Reduction ratio
Rotational direction
Speed (min–1)
Unit of permissible torque: upper (N·m) / lower (lb-in)
MZ9G3B toMZ9G200B
MY9G3B toMY9G200B
Applicable gear head
ball bearing(hinge not attached)
ball bearing(hinge attached)
Connection diagram Speed-torque characteristics
00 1800
1.5
1.0
0.5
15001000500
60Hz 200V
50Hz 200V
(N·m)
Speed (min–1)
Tor
que
150
100
50
200
(oz-in)
M9MZ60G4YG(A)
* Please read your User's manual carefully so that you will understand the operation and safety precautions before attempting to operate the system.
B-140
• Specifications
• Permissible torque at output shaft of gear head* The speed shown below is a calculated value based on the synchronous rotational speed. Depending on the load, the speed is less than the indicated value by 2 to 20%.
• The specifications and wire connections of the round shaft motor are the same as those of the pinion shaft type. For the dimensional outline drawing, refer to page B-164.
Model list B-128Coding system B-127System configuration B-127Features B-126
• The models with a motor model number to which “A” is suffixed are not sold or available in Japan.
140.5(5.53)
120(4.72) 20.5(0.81)7.5(0.30)40(1.57) 2(0.08)
ø85
h7
CWCCW
5 motor leadwires 300±30 mm (11.8±1.18 inch)AWG20
92 m
m s
q.(3
.62
inch
sq.
)
4–ø6.5(ø0.26)ø104(ø4.09)
90 mm sq.(3.54 inch sq.)
(ø3.
35h7
)
O-ring
M9MZ60G4YG(A) 4P 60 W 200 V / 220 V / 230 V (with fan)
(Note) Because the dimensions may be subject to change, also check the determinate dimensions if the gear head is to be used for design.
B-141
Helical
gear
Module
0.6Numberof teeth
9
Mass2.7 kg5.95 lb
Ind
uctio
nm
oto
rR
eversible
mo
tor
3-ph
asem
oto
rE
lectrom
agn
eticb
rakem
oto
rV
ariable
speed
ind
uctio
nm
oto
rV
ariable
speed
reversible
mo
tor
Variable
speedelectrom
agneticbrake
single-phasem
otorV
ariable
speed
un
itm
oto
rC
&B
mo
tor
2-poleround
shaftm
oto
rG
earh
eadG
earh
ead-in
ch(U
.S.A
.)90mm (3.54inch) sq. 60 W
Motor (dimensions) Scale: 1/4, Unit: mm (inch)
Gear head combination B-162 Round shaft motor B-164 Decimal gear head B-448 Gear head -inch (U.S.A.) B-449 Controls C-4 Option D-2
Note) MZ / MY is available for a gear head of either type.
ø15
h7(ø
0.59
h7)
ø34
(ø1.
34) 12
(0.4
7)18
(0.7
1)
5(0.20)
90 mm sq.(3.54 inch sq.)
ø104(ø4.09)
4–ø7(ø0.28)
29(1.14)
25(0.98)
7(0.28)
60(2.36) 38(1.50)
5(0.
20)
ø34
(ø1.
34)
ø15
h7(ø
0.59
h7)
110(
4.33
)13
0(5.
12)
60(2.36)36(1.42)4–ø8.5
(ø0.33)
4–ø6.5(ø0.26)
60(2.36) 38(1.50)7(0.28)
29(1.14)
12(0.47)8(0.31)
25(0.98)
18(0.71)
12(0.47)
ø104
(ø4.09)
90 m
m s
q.(3
.54
inch
sq.
)
60(2
.36)
Gear head (dimensions) Scale: 1/4, Unit: mm (inch)
MZ9G B (ball bearing / hinge not attached) MY9G B (ball bearing / hinge attached)Mass 1.4 kg (3.09 lb) Mass 1.4 kg (3.09 lb)
Key and keyway(dimensions) [attachment]
25(0.98)
5 0 -0.
030
12 0
-0
.15
5 0
-0.030
0.20 0
-0.001
5+0.050
0
( )
0.20
0
-
0.00
1(
)
0.20+0.002
0( )
0.47
0
-0
.006
(
)
MZ9G BMY9G B
155.5(6.12)
135(5.31) 20.5(0.81)7.5(0.30)40(1.57) 2(0.08)
ø85
h7
92 m
m s
q.
3 motor leadwires 300±30 mm (11.8±1.18 inch)AWG20
CWCCW
(3.6
2 in
ch s
q.)
4–ø6.5(ø0.26)ø104(ø4.09)
90 mm sq.(3.54 inch sq.)
(ø3.
35h7
)
O-ring
Change any two lead wires of R, S and T for CW rotation.
R
S
T
White
Gray
Black
CCW(counterclockwise)
3-phase motor (leadwire)
90 mmsq. M9MZ90G4Y
1.6 (227)
1.1 (156)
2.0 (283)
1.4 (198)
0.63 (89.2)
0.53 (75.1)
0.62 (87.8)
0.52 (73.6)
4 90
200
220
50
60
50
60
141
137
143
137
0.62
0.56
0.65
0.56
1350
1625
1400
1650
2.0
1.8
2.2
2.0
Cont.
Cont.
Motor model No.
Rating
SizeNumber
of pole
(P)
Output
(W)
Voltage
(V)
Frequency
(Hz)
Rating
(min)Input
(W)
Current
(A)
TorqueN·m
(oz-in)
Starting torque
N·m
(oz-in)
Starting
current
(A)Speed
(min–1)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
6002.53
5003
3.6
2506
7.2
30056
3604.25
7502
2.4
9001.72
10001.51.8
12001.31.5
15001
1.2
18000.81
1.18(10.4)
1.37(12.1)
1.86(16.5)
2.25(19.9)
2.84(25.1)
3.43(30.4)
3.72(32.9)
4.70(41.6)
5.68(50.3)
6.76(59.8)
7.55(66.8)
9.21(81.5)
10.9(96.5)
13.0(115)
18.3(162)
19.6(173)
1.37(12.1)
1.67(14.8)
2.25(19.9)
2.74(24.3)
3.43(30.4)
4.12(36.5)
4.51(39.9)
5.68(50.3)
6.76(59.8)
8.04(71.2)
9.02(79.8)
10.9(96.5)
13.0(115)
15.7(139)
19.6(173)
19.6(173)
3
500
600
3.6
416.7
500
5
300
360
6
250
300
7.5
200
240
9
166.7
200
10
150
180
12.5
120
144
15
100
120
18
83.3
100
20
75
90
25
60
72
30
50
60
36
41.7
50
50
30
36
60
25
30
75
20
24
90
16.7
20
100
15
18
120
12.5
15
180
8.3
10
200
7.5
9
150
10
12
Same as motor rotational directionReverse to motorrotational direction
• Permissible torque at output shaft of gear head using decimal gear head
MZ9G10XB
MZ9G B(ball bearing / hinge not attached)
MY9G B(ball bearing / hinge attached)
Applicable gear head
Bearing Decimalgear head
Speed(min–1)
Permissibletorque
50Hz60Hz
N·m(lb-in)
Rotational direction
Reduction ratio
Same as motor rotational direction Same as motor rotational directionReverse to motor rotational direction
50Hz60Hz
50Hz
60Hz
Reduction ratio
Rotational direction
Speed (min–1)
Unit of permissible torque: upper (N·m) / lower (lb-in)
MZ9G3B toMZ9G200B
MY9G3B toMY9G200B
Applicable gear head
ball bearing(hinge not attached)
ball bearing(hinge attached)
Connection diagram Speed-torque characteristics
0
2.0
2.5
1.5
1.0
0.5
0 180015001000500
60Hz 200V60Hz 220V
50Hz 200V
50Hz 220V
Speed (min–1)
Tor
que
(oz-in)
200
100
300
(N·m)
M9MZ90G4Y
M9MZ90G4Y 4P 90 W 200 V / 220 V (with fan)
* Please read your User's manual carefully so that you will understand the operation and safety precautions before attempting to operate the system. (Note) Because the dimensions may be subject to change, also check the determinate dimensions if the gear head is to be used for design.
B-142 B-143
• Specifications
• Permissible torque at output shaft of gear head* The speed shown below is a calculated value based on the synchronous rotational speed. Depending on the load, the speed is less than the indicated value by 2 to 20%.
• The specifications and wire connections of the round shaft motor are the same as those of the pinion shaft type. For the dimensional outline drawing, refer to page B-164.
* Diameter of applicable cabtyre cable to be ø8(ø0.31) to ø12(ø0.47).
Helical
gear
Module
0.6Numberof teeth
9
Mass3.2 kg7.05 lb
Model list B-128Coding system B-127System configuration B-127Features B-126
Ind
uctio
nm
oto
rR
eversible
mo
tor
3-ph
asem
oto
rE
lectrom
agn
eticb
rakem
oto
rV
ariable
speed
ind
uctio
nm
oto
rV
ariable
speed
reversible
mo
tor
Variable
speedelectrom
agneticbrake
single-phasem
otorV
ariable
speed
un
itm
oto
rC
&B
mo
tor
2-poleround
shaftm
oto
rG
earh
eadG
earh
ead-in
ch(U
.S.A
.)90mm (3.54inch) sq. 90 W
Motor (dimensions) Scale: 1/4, Unit: mm (inch)
Gear head combination B-162 Round shaft motor B-164 Decimal gear head B-448 Gear head -inch (U.S.A.) B-449 Controls C-4 Option D-2
Note) MZ / MY is available for a gear head of either type.
ø15
h7(ø
0.59
h7)
ø34
(ø1.
34) 12
(0.4
7)18
(0.7
1)
5(0.20)
90 mm sq.(3.54 inch sq.)
ø104(ø4.09)
4–ø7(ø0.28)
29(1.14)
25(0.98)
7(0.28)
60(2.36) 38(1.50)
5(0.
20)
ø34
(ø1.
34)
ø15
h7(ø
0.59
h7)
110(
4.33
)13
0(5.
12)
60(2.36)36(1.42)4–ø8.5
(ø0.33)
4–ø6.5(ø0.26)
60(2.36) 38(1.50)7(0.28)
29(1.14)
12(0.47)8(0.31)
25(0.98)
18(0.71)
12(0.47)
ø104
(ø4.09)
90 m
m s
q.(3
.54
inch
sq.
)
60(2
.36)
Gear head (dimensions) Scale: 1/4, Unit: mm (inch)
MZ9G B (ball bearing / hinge not attached) MY9G B (ball bearing / hinge attached)Mass 1.4 kg (3.09 lb) Mass 1.4 kg (3.09 lb)
Key and keyway(dimensions) [attachment]
25(0.98)
5 0 -0.
030
12 0
-0
.15
5 0
-0.030
0.20 0
-0.001
5+0.050
0
( )
0.20
0
-
0.00
1(
)
0.20+0.002
0( )
0.47
0
-0
.006
(
)
MZ9G BMY9G B
(Refer to page A-58 for connection of thermal protector.)
CCW(counterclockwise)
R
S
T
White
Gray
Black
Blue
Blue TPThermal protector
Change any two lead wires of R, S and T for CW rotation.
3-phase motor (leadwire)
90 mmsq.
M9MZ90G4YGM9MZ90G4YGA
1.6 (227)
1.1 (156)
1.4 (198)
1.6 (227)
0.63 (89.2)
0.53 (75.1)
0.52 (73.6)
0.51 (72.2)
4 90
50
60
60
60
200
220
230
142
138
137
137
0.62
0.56
0.56
0.58
1350
1625
1650
1675
2.0
1.8
2.0
2.1
Cont.
Motor model No.
Rating
SizeNumber
of pole
(P)
Output
(W)
Voltage
(V)
Frequency
(Hz)
Rating
(min)Input
(W)
Current
(A)
TorqueN·m
(oz-in)
Starting torque
N·m
(oz-in)
Starting
current
(A)Speed
(min–1)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
6002.53
5003
3.6
2506
7.2
30056
3604.25
7502
2.4
9001.72
10001.51.8
12001.31.5
15001
1.2
18000.81
1.18(10.4)
1.37(12.1)
1.86(16.5)
2.25(19.9)
2.84(25.1)
3.43(30.4)
3.72(32.9)
4.70(41.6)
5.68(50.3)
6.76(59.8)
7.55(66.8)
9.21(81.5)
10.9(96.5)
13.0(115)
18.3(162)
19.6(173)
1.37(12.1)
1.67(14.8)
2.25(19.9)
2.74(24.3)
3.43(30.4)
4.12(36.5)
4.51(39.9)
5.68(50.3)
6.76(59.8)
8.04(71.2)
9.02(79.8)
10.9(96.5)
13.0(115)
15.7(139)
19.6(173)
19.6(173)
3
500
600
3.6
416.7
500
5
300
360
6
250
300
7.5
200
240
9
166.7
200
10
150
180
12.5
120
144
15
100
120
18
83.3
100
20
75
90
25
60
72
30
50
60
36
41.7
50
50
30
36
60
25
30
75
20
24
90
16.7
20
100
15
18
120
12.5
15
180
8.3
10
200
7.5
9
150
10
12
Same as motor rotational directionReverse to motorrotational direction
• Permissible torque at output shaft of gear head using decimal gear head
MZ9G10XB
MZ9G B(ball bearing / hinge not attached)
MY9G B(ball bearing / hinge attached)
Applicable gear head
Bearing Decimalgear head
Speed(min–1)
Permissibletorque
50Hz60Hz
N·m(lb-in)
Rotational direction
Reduction ratio
Same as motor rotational direction Same as motor rotational directionReverse to motor rotational direction
50Hz60Hz
50Hz
60Hz
Reduction ratio
Rotational direction
Speed (min–1)
Unit of permissible torque: upper (N·m) / lower (lb-in)
MZ9G3B toMZ9G200B
MY9G3B toMY9G200B
Applicable gear head
ball bearing(hinge not attached)
ball bearing(hinge attached)
Connection diagram Speed-torque characteristics
00 1800
2.0
1.5
1.0
0.5
15001000500
200V 60Hz
200V 50Hz
(N·m)
Speed (min–1)
Tor
que
(oz-in)
100
200
M9MZ90G4YG(A)
* Please read your User's manual carefully so that you will understand the operation and safety precautions before attempting to operate the system.
B-144
• Specifications
• Permissible torque at output shaft of gear head* The speed shown below is a calculated value based on the synchronous rotational speed. Depending on the load, the speed is less than the indicated value by 2 to 20%.
• The specifications and wire connections of the round shaft motor are the same as those of the pinion shaft type. For the dimensional outline drawing, refer to page B-164.
Model list B-128Coding system B-127System configuration B-127Features B-126
• The models with a motor model number to which “A” is suffixed are not sold or available in Japan.
155.5(6.12)
135(5.31) 20.5(0.81)7.5(0.30)40(1.57) 2(0.08)
ø85
h7
92 m
m s
q.
5 motor leadwires 300±30 mm (11.8±1.18 inch)AWG20
CWCCW
(3.6
2 in
ch s
q.)
4–ø6.5(ø0.26)ø104(ø4.09)
90 mm sq.(3.54 inch sq.)
(ø3.
35h7
)
O-ring
M9MZ90G4YG(A) 4P 90 W 200 V / 220 V / 230 V (with fan)
(Note) Because the dimensions may be subject to change, also check the determinate dimensions if the gear head is to be used for design.
B-145
Helical
gear
Module
0.6Numberof teeth
9
Mass3.2 kg7.05 lb
Ind
uctio
nm
oto
rR
eversible
mo
tor
3-ph
asem
oto
rE
lectrom
agn
eticb
rakem
oto
rV
ariable
speed
ind
uctio
nm
oto
rV
ariable
speed
reversible
mo
tor
Variable
speedelectrom
agneticbrake
single-phasem
otorV
ariable
speed
un
itm
oto
rC
&B
mo
tor
2-poleround
shaftm
oto
rG
earh
eadG
earh
ead-in
ch(U
.S.A
.)90mm (3.54inch) sq. 90 W
Motor (dimensions) Scale: 1/4, Unit: mm (inch)
Gear head combination B-162 Round shaft motor B-164 Decimal gear head B-448 Gear head -inch (U.S.A.) B-449 Controls C-4 Option D-2
Note) MZ / MY is available for a gear head of either type.
ø15
h7(ø
0.59
h7)
ø34
(ø1.
34) 12
(0.4
7)18
(0.7
1)
5(0.20)
90 mm sq.(3.54 inch sq.)
ø104(ø4.09)
4–ø7(ø0.28)
29(1.14)
25(0.98)
7(0.28)
60(2.36) 38(1.50)
5(0.
20)
ø34
(ø1.
34)
ø15
h7(ø
0.59
h7)
110(
4.33
)13
0(5.
12)
60(2.36)36(1.42)4–ø8.5
(ø0.33)
4–ø6.5(ø0.26)
60(2.36) 38(1.50)7(0.28)
29(1.14)
12(0.47)8(0.31)
25(0.98)
18(0.71)
12(0.47)
ø104
(ø4.09)
90 m
m s
q.(3
.54
inch
sq.
)
60(2
.36)
Gear head (dimensions) Scale: 1/4, Unit: mm (inch)
MZ9G B (ball bearing / hinge not attached) MY9G B (ball bearing / hinge attached)Mass 1.4 kg (3.09 lb) Mass 1.4 kg (3.09 lb)
Key and keyway(dimensions) [attachment]
25(0.98)
5 0 -0.
030
12 0
-0
.15
5 0
-0.030
0.20 0
-0.001
5+0.050
0
( )
0.20
0
-
0.00
1(
)
0.20+0.002
0( )
0.47
0
-0
.006
(
)
MZ9G BMY9G B
96.3(3.79)
85(3.35)
75(2.95) 1(0.04)30(1.18)max.
11.3(0.44)
7(0.28) 2(0.08)
ø75
h7
80 mm sq.(3.15 inch sq.)
ø94(ø3.70)
CCWCW
67(2.64)
MA
Xø
86(ø
3.39
)(2
0(0.
79))
(45(
1.77
))
4–ø5.5(ø0.22)
O-ring
(ø2.
95h7
)
Change any two lead wires of U, V and W for CW rotation.
R
S
T W
V
UWhite
Gray
Black
CCW(counterclockwise)
UV
W
Terminal
Screws for earth
3-phase motor (sealed connector)
80 mmsq. M8MX25GK4Y
0.54 (76.5)
0.40 (56.6)
0.66 (93.5)
0.50 (70.8)
0.18 (25.5)
0.15 (21.2)
0.18 (25.5)
0.15 (21.2)
4 25
200
220
50
60
50
60
50
47
54
49
0.25
0.22
0.27
0.23
1350
1625
1375
1650
0.62
0.58
0.67
0.64
Cont.
Cont.
Motor model No.
Rating
SizeNumber
of pole
(P)
Output
(W)
Voltage
(V)
Frequency
(Hz)
Rating
(min)Input
(W)
Current
(A)
TorqueN·m
(oz-in)
Starting torque
N·m
(oz-in)
Starting
current
(A)Speed
(min–1)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
6002.53
5003
3.6
2506
7.2
30056
3604.25
2007.59
7502
2.4
9001.72
10001.51.8
12001.31.5
15001
1.2
18000.81
0.39(3.45)
0.47(4.16)
0.66(5.84)
0.78(6.90)
0.98(8.67)
1.18(10.4)
1.27(11.2)
1.57(13.9)
1.96(17.3)
2.35(20.8)
2.55(22.6)
3.14(27.8)
3.82(33.8)
4.61(40.8)
6.37(56.4)
7.64(67.6)
7.84(69.4)
0.32(2.83)
0.39(3.45)
0.55(4.87)
0.66(5.84)
0.81(7.17)
0.98(8.67)
1.08(9.56)
1.27(11.2)
1.57(13.9)
1.96(17.3)
2.06(18.2)
2.65(23.5)
3.14(27.8)
3.82(33.8)
5.29(46.8)
6.37(56.4)
7.84(69.4)
3
500
600
3.6
416.7
500
5
300
360
6
250
300
7.5
200
240
9
166.7
200
10
150
180
12.5
120
144
15
100
120
18
83.3
100
20
75
90
25
60
72
30
50
60
36
41.7
50
50
30
36
60
25
30
75
20
24
90
16.7
20
100
15
18
120
12.5
15
150
10
12
180
8.3
10
• Permissible torque at output shaft of gear head using decimal gear head
MX8G10XBSame as motor
rotational direction Reverse to motor rotational direction
MX8G B(ball bearing)MX8G M
(metal bearing)
Same as motor rotational direction Reverse to motor rotational direction
Applicable gear head
Bearing Decimalgear head
Speed(min–1)
Permissibletorque
50Hz60Hz
N·m(lb-in)
Rotational direction
Reduction ratio
50Hz60Hz
50Hz
60Hz
Reduction ratio
Rotational direction
Speed (min–1)
Unit of permissible torque: upper (N·m) / lower (lb-in)
MX8G3B toMX8G180B(ball bearing)MX8G3M toMX8G180M(metal bearing)
Applicable gear head
Connection diagram Speed-torque characteristics
00 1800
1.0
0.8
0.6
0.4
0.2
15001000500
60Hz 200V
60Hz 220V50Hz 200V 50Hz 220V
(N·m)
Speed (min–1)
Tor
que
(oz-in)
100
50
M8MX25GK4Y
M8MX25GK4Y 4P 25 W 200 V / 220 V
* Please read your User's manual carefully so that you will understand the operation and safety precautions before attempting to operate the system. (Note) Because the dimensions may be subject to change, also check the determinate dimensions if the gear head is to be used for design.
B-146 B-147
• Specifications
• Permissible torque at output shaft of gear head* The speed shown below is a calculated value based on the synchronous rotational speed. Depending on the load, the speed is less than the indicated value by 2 to 20%.
• The specifications and wire connections of the round shaft motor are the same as those of the pinion shaft type. For the dimensional outline drawing, refer to page B-165.
* Diameter of applicable cabtyre cable to be ø8(ø0.31) to ø12(ø0.47).
Helical
gear
Module
0.5Numberof teeth
9
Mass1.8 kg3.97 lb
Model list B-128Coding system B-127System configuration B-127Features B-126
Ind
uctio
nm
oto
rR
eversible
mo
tor
3-ph
asem
oto
rE
lectrom
agn
eticb
rakem
oto
rV
ariable
speed
ind
uctio
nm
oto
rV
ariable
speed
reversible
mo
tor
Variable
speedelectrom
agneticbrake
single-phasem
otorV
ariable
speed
un
itm
oto
rC
&B
mo
tor
2-poleround
shaftm
oto
rG
earh
eadG
earh
ead-in
ch(U
.S.A
.)80mm (3.15inch) sq. 25 W
Motor (dimensions) Scale: 1/3, Unit: mm (inch)
Gear head combination B-163 Round shaft motor B-165 Decimal gear head B-448 Gear head -inch (U.S.A.) B-449 Controls C-4 Option D-2
ø10
h7ø
30(ø
1.18
)(ø
0.39
h7)
7.5(
0.30
)15
(0.5
9)
4(0.16)
80 mm sq.(3.15 inch sq.)
ø94(ø3.70)
4–ø5.5(ø0.22)
30(1.18) 32(1.26)25
(0.98)6(0.24)
Gear head (dimensions) Scale: 1/3, Unit: mm (inch)
MX8G B (ball bearing) / MX8G M (metal bearing) Mass 0.6 kg (1.32 lb)
Key and keyway(dimensions) [attachment]
25(0.98)
4 0 -0.
030
7.5 0
-
0.15
4 0
-0.030
0.16 0
-0.001
4+0.060
+0.010
( )
0.16
0
-
0.00
1(
)
0.16+0.002
+0.0004( )
0.3 0
-
0.00
6(
)
MX8G B(M)
96.3(3.79)
85(3.35)
75(2.95) 1(0.04)30(1.18)max.
11.3(0.44)
7(0.28) 2(0.08)
ø75
h7
80 mm sq.(3.15 inch sq.)
ø94(ø3.70)
CCWCW
67(2.64)
MA
Xø
86(ø
3.39
)(2
0(0.
79))
(45(
1.77
))
4–ø5.5(ø0.22)
O-ring
(ø2.
95h7
)
(Refer to page A-58 for connection of thermal protector.)
PP
UV
W
Change any two lead wires of U, V and W for CW rotation.CCW (counterclockwise)
W
V
U
P
P
R
S
T
White
Gray
BlackThermal protector
Blue
Blue TP
Terminal
Screws for earth
3-phase motor (sealed connector)
M8MX25GK4YGM8MX25GK4YGA
M8MX25GK4CGM8MX25GK4CGA
0.54 (76.5)
0.40 (56.6)
0.50 (70.8)
0.54 (76.5)
0.50 (70.8)
0.56 (79.3)
0.18 (25.5)
0.15 (21.2)
0.14 (19.8)
0.14 (19.8)
0.18 (25.5)
0.18 (25.5)
80 mmsq.
4
4
25
25
50
60
60
60
50
50
200
220
230
380
400
50
47
49
50
49
52
0.25
0.22
0.23
0.24
0.12
0.12
1350
1625
1650
1675
1325
1325
0.62
0.58
0.64
0.65
0.29
0.32
Cont.
Cont.
Motor model No.
Rating
SizeNumber
of pole
(P)
Output
(W)
Voltage
(V)
Frequency
(Hz)
Rating
(min)Input
(W)
Current
(A)
TorqueN·m
(oz-in)
Starting torque
N·m
(oz-in)
Starting
current
(A)Speed
(min–1)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
7.84
(69.4)
6002.53
5003
3.6
2506
7.2
30056
3604.25
2007.59
7502
2.4
9001.72
10001.51.8
12001.31.5
15001
1.2
18000.81
0.39(3.45)
0.47(4.16)
0.66(5.84)
0.78(6.90)
0.98(8.67)
1.18(10.4)
1.27(11.2)
1.57(13.9)
1.96(17.3)
2.35(20.8)
2.55(22.6)
3.14(27.8)
3.82(33.8)
4.61(40.8)
6.37(56.4)
7.64(67.6)
7.84(69.4)
0.32(2.83)
0.39(3.45)
0.55(4.87)
0.66(5.84)
0.81(7.17)
0.98(8.67)
1.08(9.56)
1.27(11.2)
1.57(13.9)
1.96(17.3)
2.06(18.2)
2.65(23.5)
3.14(27.8)
3.82(33.8)
5.29(46.8)
6.37(56.4)
7.84(69.4)
3
500
600
3.6
416.7
500
5
300
360
6
250
300
7.5
200
240
9
166.7
200
10
150
180
12.5
120
144
15
100
120
18
83.3
100
20
75
90
25
60
72
30
50
60
36
41.7
50
50
30
36
60
25
30
75
20
24
90
16.7
20
100
15
18
120
12.5
15
150
10
12
180
8.3
10
Same as motor rotational direction Reverse to motor rotational direction
50Hz60Hz
50Hz
60Hz
Reduction ratio
Rotational direction
Speed (min–1)
Unit of permissible torque: upper (N·m) / lower (lb-in)
MX8G3B toMX8G180B(ball bearing)MX8G3M toMX8G180M(metal bearing)
Applicable gear head
• Permissible torque at output shaft of gear head using decimal gear head
MX8G10XBSame as motor
rotational direction Reverse to motor rotational direction
MX8G B(ball bearing)MX8G M
(metal bearing)
Applicable gear head
Bearing Decimalgear head
Speed(min–1)
Permissibletorque
50Hz60Hz
N·m(lb-in)
Rotational direction
Reduction ratio
Connection diagram Speed-torque characteristics
60Hz 200V
50Hz 200V
00 1800
1.0
0.8
0.6
0.4
0.2
15001000500
(N·m)
Speed (min–1)
Tor
que
(oz-in)
100
50
M8MX25GK4YG(A)
M8MX25GK4YG(A)M8MX25GK4CG(A)
4P 25 W 200 V / 220 V / 230 V4P 25 W 380 V / 400 V
* Diameter of applicable cabtyre cable to be ø8(ø0.31) to ø12(ø0.47).
* Please read your User's manual carefully so that you will understand the operation and safety precautions before attempting to operate the system. (Note) Because the dimensions may be subject to change, also check the determinate dimensions if the gear head is to be used for design.
B-148 B-149
• Specifications
• Permissible torque at output shaft of gear head* The speed shown below is a calculated value based on the synchronous rotational speed. Depending on the load, the speed is less than the indicated value by 2 to 20%.
• The specifications and wire connections of the round shaft motor are the same as those of the pinion shaft type. For the dimensional outline drawing, refer to page B-165.
Helical
gear
Module
0.5Numberof teeth
9
Mass1.8 kg3.97 lb
Model list B-128Coding system B-127System configuration B-127Features B-126
Ind
uctio
nm
oto
rR
eversible
mo
tor
3-ph
asem
oto
rE
lectrom
agn
eticb
rakem
oto
rV
ariable
speed
ind
uctio
nm
oto
rV
ariable
speed
reversible
mo
tor
Variable
speedelectrom
agneticbrake
single-phasem
otorV
ariable
speed
un
itm
oto
rC
&B
mo
tor
2-poleround
shaftm
oto
rG
earh
eadG
earh
ead-in
ch(U
.S.A
.)80mm (3.15inch) sq. 25 W
Motor (dimensions) Scale: 1/3, Unit: mm (inch)
Gear head combination B-163 Round shaft motor B-165 Decimal gear head B-448 Gear head -inch (U.S.A.) B-449 Controls C-4 Option D-2
• The models with a motor model number to which “A” is suffixed are not sold or available in Japan.
ø10
h7ø
30(ø
1.18
)(ø
0.39
h7)
7.5(
0.30
)15
(0.5
9)
4(0.16)
80 mm sq.(3.15 inch sq.)
ø94(ø3.70)
4–ø5.5(ø0.22)
30(1.18) 32(1.26)25
(0.98)6(0.24)
Gear head (dimensions) Scale: 1/3, Unit: mm (inch)
MX8G B (ball bearing) / MX8G M (metal bearing) Mass 0.6 kg (1.32 lb)
Key and keyway(dimensions) [attachment]
25(0.98)
4 0 -0.
030
7.5 0
-
0.15
4 0
-0.030
0.16 0
-0.001
4+0.060
+0.010
( )
0.16
0
-
0.00
1(
)
0.16+0.002
+0.0004( )
0.3 0
-
0.00
6(
)
MX8G B(M)
ø85
h7(4
5(1.
77))
117.8(4.64)
105(4.13) 12.8(0.50)
7.5(0.30) 2(0.08)
75(2.95) 1(0.04)30(1.18)max.
MA
Xø
95(ø
3.74
)(2
0(0.
79))
CCWCW
67(2.64)
4–ø6.5(ø0.26)
90 mm sq.(3.54 inch sq.)
O-ring
ø104(ø4.09)
(ø3.
35h7
)
Change any two lead wires of U, V and W for CW rotation.
R
S
T W
V
UWhite
Gray
Black
CCW(counterclockwise)
UV
W
Terminal
Screws for earth
3-phase motor (sealed connector)
90 mmsq. M9MX40GK4Y
0.72 (102)
0.51 (72.2)
0.88 (125)
0.63 (89.2)
0.28 (39.7)
0.24 (34.0)
0.27 (38.2)
0.23 (32.6)
4 40
200
220
50
60
50
60
69
68
70
66
0.31
0.29
0.32
0.28
1350
1625
1375
1675
0.90
0.82
1.0
0.91
Cont.
Cont.
Motor model No.
Rating
SizeNumber
of pole
(P)
Output
(W)
Voltage
(V)
Frequency
(Hz)
Rating
(min)Input
(W)
Current
(A)
TorqueN·m
(oz-in)
Starting torque
N·m
(oz-in)
Starting
current
(A)Speed
(min–1)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
6002.53
5003
3.6
2506
7.2
30056
3604.25
2007.59
7502
2.4
9001.72
10001.51.8
12001.31.5
15001
1.2
18000.81
0.66(5.84)
0.78(6.90)
1.08(9.56)
1.27(11.2)
1.57(13.9)
1.86(16.5)
2.25(19.9)
2.74(24.3)
3.23(28.6)
3.92(34.7)
4.41(39.0)
5.29(46.8)
6.37(56.4)
7.94(70.3)
9.80(86.7)
9.80(86.7)
0.55(4.87)
0.66(5.84)
0.90(7.97)
1.08(9.56)
1.27(11.2)
1.57(13.9)
1.76(15.6)
2.25(19.9)
2.74(24.3)
3.23(28.6)
3.53(31.2)
4.41(39.0)
5.29(46.8)
6.37(56.4)
8.82(78.1)
9.80(86.7)
3
500
600
3.6
416.7
500
5
300
360
6
250
300
7.5
200
240
9
166.7
200
10
150
180
12.5
120
144
15
100
120
18
83.3
100
20
75
90
25
60
72
30
50
60
36
41.7
50
50
30
36
60
25
30
75
20
24
90
16.7
20
100
15
18
120
12.5
15
150
10
12
180
8.3
10
• Permissible torque at output shaft of gear head using decimal gear head
MX9G10XBSame as motor
rotational direction Reverse to motor rotational direction
MX9G B(ball bearing)MX9G M
(metal bearing)
Same as motor rotational direction Reverse to motor rotational direction
Applicable gear head
Bearing Decimalgear head
Speed(min–1)
Permissibletorque
50Hz60Hz
N·m(lb-in)
Rotational direction
Reduction ratio
50Hz60Hz
50Hz
60Hz
Reduction ratio
Rotational direction
Speed (min–1)
Unit of permissible torque: upper (N·m) / lower (lb-in)
MX9G3B toMX9G180B(ball bearing)MX9G3M toMX9G180M(metal bearing)
Applicable gear head
Connection diagram Speed-torque characteristics
00 1800
1.0
0.8
0.6
0.4
0.2
15001000500
60Hz 200V60Hz 220V
50Hz 200V50Hz 220V
(N·m)
Speed (min–1)
Tor
que
(oz-in)
100
50
M9MX40GK4Y
M9MX40GK4Y 4P 40 W 200 V / 220 V
* Please read your User's manual carefully so that you will understand the operation and safety precautions before attempting to operate the system. (Note) Because the dimensions may be subject to change, also check the determinate dimensions if the gear head is to be used for design.
B-150 B-151
• Specifications
• Permissible torque at output shaft of gear head* The speed shown below is a calculated value based on the synchronous rotational speed. Depending on the load, the speed is less than the indicated value by 2 to 20%.
• The specifications and wire connections of the round shaft motor are the same as those of the pinion shaft type. For the dimensional outline drawing, refer to page B-165.
* Diameter of applicable cabtyre cable to be ø8(ø0.31) to ø12(ø0.47).
Helical
gear
Module
0.55Numberof teeth
9
Mass2.8 kg6.17 lb
Model list B-128Coding system B-127System configuration B-127Features B-126
Ind
uctio
nm
oto
rR
eversible
mo
tor
3-ph
asem
oto
rE
lectrom
agn
eticb
rakem
oto
rV
ariable
speed
ind
uctio
nm
oto
rV
ariable
speed
reversible
mo
tor
Variable
speedelectrom
agneticbrake
single-phasem
otorV
ariable
speed
un
itm
oto
rC
&B
mo
tor
2-poleround
shaftm
oto
rG
earh
eadG
earh
ead-in
ch(U
.S.A
.)90mm (3.54inch) sq. 40 W
Motor (dimensions) Scale: 1/3, Unit: mm (inch)
Gear head combination B-163 Round shaft motor B-165 Decimal gear head B-448 Gear head -inch (U.S.A.) B-449 Controls C-4 Option D-2
ø12
h7(ø
0.47
)
ø36
(ø1.
42) 9.
5(0.
37)
18(0
.71)
4(0.16)
90 mm sq.(3.54 inch sq.)
ø104(ø4.09)
4–ø7(ø0.28)
37(1.46) 32(1.26)
25(0.98)
5(0.20)
Gear head (dimensions) Scale: 1/3, Unit: mm (inch)
MX9G B (ball bearing) / MX9G M (metal bearing) Mass 0.8 kg (1.76 lb)
Key and keyway(dimensions) [attachment]
25(0.98)
4 0 -0.
030
9.5 0
-
0.15
4 0
-0.030
0.16 0
-0.001
4+0.060
+0.010
( )
0.16
0
-
0.00
1(
)
0.16+0.002
+0.0004( )
0.37
0
-0
.006
(
)
MX9G B(M)
ø85
h7(4
5(1.
77))
117.8(4.64)
105(4.13) 12.8(0.50)
7.5(0.30) 2(0.08)
75(2.95) 1(0.04)30(1.18)max.
MA
Xø
95(ø
3.74
)(2
0(0.
79))
CCWCW
67(2.64)
4–ø6.5(ø0.26)
90 mm sq.(3.54 inch sq.)
O-ring
ø104(ø4.09)
(ø3.
35h7
)
(Refer to page A-58 for connection of thermal protector.)
PP
UV
W
Change any two lead wires of U, V and W for CW rotation.CCW (counterclockwise)
W
V
U
P
P
R
S
T
White
Gray
BlackThermal protector
Blue
Blue TP
Terminal
Screws for earth
3-phase motor (sealed connector)
M9MX40GK4YGM9MX40GK4YGA
M9MX40GK4CGM9MX40GK4CGA
0.72 (102)
0.51 (72.2)
0.63 (89.2)
0.69 (97.7)
0.64 (90.6)
0.74 (105)
0.28 (39.7)
0.24 (34.0)
0.23 (32.6)
0.23 (32.6)
0.29 (41.1)
0.28 (39.7)
90 mmsq.
4
4
40
40
50
60
60
60
50
50
200
220
230
380
400
69
68
66
66
68
66
0.31
0.29
0.28
0.29
0.15
0.15
1350
1625
1675
1675
1325
1350
0.90
0.82
0.91
0.96
0.44
0.47
Cont.
Cont.
Motor model No.
Rating
SizeNumber
of pole
(P)
Output
(W)
Voltage
(V)
Frequency
(Hz)
Rating
(min)Input
(W)
Current
(A)
TorqueN·m
(oz-in)
Starting torque
N·m
(oz-in)
Starting
current
(A)Speed
(min–1)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
9.80
(86.7)
6002.53
5003
3.6
2506
7.2
30056
3604.25
2007.59
7502
2.4
9001.72
10001.51.8
12001.31.5
15001
1.2
18000.81
0.66(5.84)
0.78(6.90)
1.08(9.56)
1.27(11.2)
1.57(13.9)
1.86(16.5)
2.25(19.9)
2.74(24.3)
3.23(28.6)
3.92(34.7)
4.41(39.0)
5.29(46.8)
6.37(56.4)
7.94(70.3)
9.80(86.7)
9.80(86.7)
0.55(4.87)
0.66(5.84)
0.90(7.97)
1.08(9.56)
1.27(11.2)
1.57(13.9)
1.76(15.6)
2.25(19.9)
2.74(24.3)
3.23(28.6)
3.53(31.2)
4.41(39.0)
5.29(46.8)
6.37(56.4)
8.82(78.1)
9.80(86.7)
3
500
600
3.6
416.7
500
5
300
360
6
250
300
7.5
200
240
9
166.7
200
10
150
180
12.5
120
144
15
100
120
18
83.3
100
20
75
90
25
60
72
30
50
60
36
41.7
50
50
30
36
60
25
30
75
20
24
90
16.7
20
100
15
18
120
12.5
15
150
10
12
180
8.3
10
Same as motor rotational direction Reverse to motor rotational direction
50Hz60Hz
50Hz
60Hz
Reduction ratio
Rotational direction
Speed (min–1)
Unit of permissible torque: upper (N·m) / lower (lb-in)
MX9G3B toMX9G180B(ball bearing)MX9G3M toMX9G180M(metal bearing)
Applicable gear head
• Permissible torque at output shaft of gear head using decimal gear head
MX9G10XBSame as motor
rotational direction Reverse to motor rotational direction
MX9G B(ball bearing)MX9G M
(metal bearing)
Applicable gear head
Bearing Decimalgear head
Speed(min–1)
Permissibletorque
50Hz60Hz
N·m(lb-in)
Rotational direction
Reduction ratio
Connection diagram Speed-torque characteristics
00 1800
1.0
0.8
0.6
0.4
0.2
15001000500
200V 60Hz
200V 50Hz
(N·m)
Speed (min–1)
Tor
que
(oz-in)
100
50
M9MX40GK4YG(A)
M9MX40GK4YG(A)M9MX40GK4CG(A)
4P 40 W 200 V / 220 V / 230 V4P 40 W 380 V / 400 V
* Diameter of applicable cabtyre cable to be ø8(ø0.31) to ø12(ø0.47).
* Please read your User's manual carefully so that you will understand the operation and safety precautions before attempting to operate the system. (Note) Because the dimensions may be subject to change, also check the determinate dimensions if the gear head is to be used for design.
B-152 B-153
• Specifications
• Permissible torque at output shaft of gear head* The speed shown below is a calculated value based on the synchronous rotational speed. Depending on the load, the speed is less than the indicated value by 2 to 20%.
• The specifications and wire connections of the round shaft motor are the same as those of the pinion shaft type. For the dimensional outline drawing, refer to page B-165.
Helical
gear
Module
0.55Numberof teeth
9
Mass2.8 kg6.17 lb
Model list B-128Coding system B-127System configuration B-127Features B-126
Ind
uctio
nm
oto
rR
eversible
mo
tor
3-ph
asem
oto
rE
lectrom
agn
eticb
rakem
oto
rV
ariable
speed
ind
uctio
nm
oto
rV
ariable
speed
reversible
mo
tor
Variable
speedelectrom
agneticbrake
single-phasem
otorV
ariable
speed
un
itm
oto
rC
&B
mo
tor
2-poleround
shaftm
oto
rG
earh
eadG
earh
ead-in
ch(U
.S.A
.)90mm (3.54inch) sq. 40 W
Motor (dimensions) Scale: 1/3, Unit: mm (inch)
Gear head combination B-163 Round shaft motor B-165 Decimal gear head B-448 Gear head -inch (U.S.A.) B-449 Controls C-4 Option D-2
• The models with a motor model number to which “A” is suffixed are not sold or available in Japan.
ø12
h7(ø
0.47
)
ø36
(ø1.
42) 9.
5(0.
37)
18(0
.71)
4(0.16)
90 mm sq.(3.54 inch sq.)
ø104(ø4.09)
4–ø7(ø0.28)
37(1.46) 32(1.26)
25(0.98)
5(0.20)
Gear head (dimensions) Scale: 1/3, Unit: mm (inch)
MX9G B (ball bearing) / MX9G M (metal bearing) Mass 0.8 kg (1.76 lb)
Key and keyway(dimensions) [attachment]
25(0.98)
4 0 -0.
030
9.5 0
-
0.15
4 0
-0.030
0.16 0
-0.001
4+0.060
+0.010
( )
0.16
0
-
0.00
1(
)
0.16+0.002
+0.0004( )
0.37
0
-0
.006
(
)
MX9G B(M)
75(2.95) 1(0.04)30(1.18)max.
CCWCW
67(2.64)
140.5(5.53)120(4.72) 20.5(0.81)
7.5(0.30)40(1.57) 2(0.08)
ø85
h7
92 m
m s
q.
(45(
1.77
))
(20(
0.79
))
4–ø6.5(ø0.26)
90 mm sq.(3.54 inch sq.)
O-ring
(3.6
2 in
ch s
q.)
ø104(ø4.09)
(ø3.
35h7
)
Change any two lead wires of U, V and W for CW rotation.
R
S
T W
V
UWhite
Gray
Black
CCW(counterclockwise)
UV
W
Terminal
Screws for earth
3-phase motor (sealed connector)
90 mmsq. M9MZ60GK4Y
1.0 (142)
0.69 (97.7)
1.2 (170)
0.87 (123)
0.42 (59.5)
0.35 (49.6)
0.41 (58.1)
0.34 (48.1)
4 60
200
220
50
60
50
60
101
96
103
98
0.45
0.41
0.46
0.40
1350
1625
1375
1650
1.3
1.2
1.5
1.3
Cont.
Cont.
Motor model No.
Rating
SizeNumber
of pole
(P)
Output
(W)
Voltage
(V)
Frequency
(Hz)
Rating
(min)Input
(W)
Current
(A)
TorqueN·m
(oz-in)
Starting torque
N·m
(oz-in)
Starting
current
(A)Speed
(min–1)
Same as motor rotational direction
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
6002.53
5003
3.6
2506
7.2
30056
3604.25
7502
2.4
9001.72
10001.51.8
12001.31.5
15001
1.2
18000.81
0.98(8.7)
1.18(10.4)
1.57(13.9)
1.96(17.3)
2.35(20.8)
2.94(26.0)
3.14(27.8)
3.92(34.7)
4.70(41.6)
5.59(49.5)
6.27(55.5)
7.55(66.8)
9.11(80.6)
11.0(97.4)
15.2(135)
17.8(158)
19.6(173)
0.78(6.9)
0.98(8.7)
1.37(12.1)
1.57(13.9)
1.96(17.3)
2.35(20.8)
2.65(23.5)
3.33(29.5)
3.92(34.7)
4.70(41.6)
5.29(46.8)
6.47(57.3)
7.55(66.8)
9.11(80.6)
12.6(112)
15.2(135)
19.6(173)
3
500
600
3.6
416.7
500
5
300
360
6
250
300
7.5
200
240
9
166.7
200
10
150
180
12.5
120
144
15
100
120
18
83.3
100
20
75
90
25
60
72
30
50
60
36
41.7
50
50
30
36
60
25
30
75
20
24
90
16.7
20
100
15
18
120
12.5
15
180
8.3
10
200
7.5
9
150
10
12
Same as motor rotational direction Same as motor rotational directionReverse to motor rotational direction
Reverse to motorrotational direction
• Permissible torque at output shaft of gear head using decimal gear head
MZ9G10XB
MZ9G B(ball bearing / Hinge not attached)
MY9G B(ball bearing / Hinge attached)
Applicable gear head
Bearing Decimalgear head
Speed(min–1)
Permissibletorque
50Hz60Hz
N·m(lb-in)
Rotational direction
Reduction ratio
50Hz60Hz
50Hz
60Hz
Reduction ratio
Rotational direction
Speed (min–1)
Unit of permissible torque: upper (N·m) / lower (lb-in)
MZ9G3B toMZ9G200B
MY9G3B toMY9G200B
Applicable gear head
ball bearing(hinge not attached)
ball bearing(hinge attached)
Connection diagram Speed-torque characteristics
00 1800
2.0
1.5
1.0
0.5
15001000500
50Hz 200V
50Hz 220V
60Hz 200V60Hz 220V
(N·m)
Speed (min–1)
Tor
que
(oz-in)
100
200
M9MZ60GK4Y
M9MZ60GK4Y 4P 60 W 200 V / 220 V (with fan)
* Please read your User's manual carefully so that you will understand the operation and safety precautions before attempting to operate the system. (Note) Because the dimensions may be subject to change, also check the determinate dimensions if the gear head is to be used for design.
B-154 B-155
• Specifications
• Permissible torque at output shaft of gear head* The speed shown below is a calculated value based on the synchronous rotational speed. Depending on the load, the speed is less than the indicated value by 2 to 20%.
• The specifications and wire connections of the round shaft motor are the same as those of the pinion shaft type. For the dimensional outline drawing, refer to page B-165.
* Diameter of applicable cabtyre cable to be ø8(ø0.31) to ø12(ø0.47).
Helical
gear
Module
0.6Numberof teeth
9
Mass3.0 kg6.61 lb
Model list B-128Coding system B-127System configuration B-127Features B-126
Ind
uctio
nm
oto
rR
eversible
mo
tor
3-ph
asem
oto
rE
lectrom
agn
eticb
rakem
oto
rV
ariable
speed
ind
uctio
nm
oto
rV
ariable
speed
reversible
mo
tor
Variable
speedelectrom
agneticbrake
single-phasem
otorV
ariable
speed
un
itm
oto
rC
&B
mo
tor
2-poleround
shaftm
oto
rG
earh
eadG
earh
ead-in
ch(U
.S.A
.)90mm (3.54inch) sq. 60 W
Motor (dimensions) Scale: 1/4, Unit: mm (inch)
Gear head combination B-163 Round shaft motor B-165 Decimal gear head B-448 Gear head -inch (U.S.A.) B-449 Controls C-4 Option D-2
Note) MZ / MY is available for a gear head of either type.
ø15
h7(ø
0.59
h7)
ø34
(ø1.
34) 12
(0.4
7)18
(0.7
1)
5(0.20)
90 mm sq.(3.54 inch sq.)
ø104(ø4.09)
4–ø7(ø0.28)
29(1.14)
25(0.98)
7(0.28)
60(2.36) 38(1.50)
5(0.
20)
ø34
(ø1.
34)
ø15
h7(ø
0.59
h7)
110(
4.33
)13
0(5.
12)
60(2.36)36(1.42)4–ø8.5
(ø0.33)
4–ø6.5(ø0.26)
60(2.36) 38(1.50)7(0.28)
29(1.14)
12(0.47)8(0.31)
25(0.98)
18(0.71)
12(0.47)
ø104
(ø4.09)
90 m
m s
q.(3
.54
inch
sq.
)
60(2
.36)
Gear head (dimensions) Scale: 1/4, Unit: mm (inch)
MZ9G B (ball bearing / hinge not attached) MY9G B (ball bearing / hinge attached)Mass 1.4 kg (3.09 lb) Mass 1.4 kg (3.09 lb)
Key and keyway(dimensions) [attachment]
25(0.98)
5 0 -0.
030
12 0
-0
.15
5 0
-0.030
0.20 0
-0.001
5+0.050
0
( )
0.20
0
-
0.00
1(
)
0.20+0.002
0( )
0.47
0
-0
.006
(
)
MZ9G BMY9G B
75(2.95) 1(0.04)30(1.18)max.
CCWCW
67(2.64)
140.5(5.53)120(4.72) 20.5(0.81)
7.5(0.30)40(1.57) 2(0.08)
ø85
h7
92 m
m s
q.
(45(
1.77
))
(20(
0.79
))
4–ø6.5(ø0.26)
90 mm sq.(3.54 inch sq.)
O-ring
(3.6
2 in
ch s
q.)
ø104(ø4.09)
(ø3.
35h7
)
M9MZ60GK4YG(A)M9MZ60GK4CG(A)
4P 60 W 200 V / 220 V / 230 V (with fan) 4P 60 W 380 V / 400 V (with fan)
* Diameter of applicable cabtyre cable to be ø8(ø0.31) to ø12(ø0.47).
(Note) Because the dimensions may be subject to change, also check the determinate dimensions if the gear head is to be used for design.
B-157
Helical
gear
Module
0.6Numberof teeth
9
Mass3.0 kg6.61 lb
Ind
uctio
nm
oto
rR
eversible
mo
tor
3-ph
asem
oto
rE
lectrom
agn
eticb
rakem
oto
rV
ariable
speed
ind
uctio
nm
oto
rV
ariable
speed
reversible
mo
tor
Variable
speedelectrom
agneticbrake
single-phasem
otorV
ariable
speed
un
itm
oto
rC
&B
mo
tor
2-poleround
shaftm
oto
rG
earh
eadG
earh
ead-in
ch(U
.S.A
.)90mm (3.54inch) sq. 60 W
Motor (dimensions) Scale: 1/4, Unit: mm (inch)
Gear head combination B-163 Round shaft motor B-165 Decimal gear head B-448 Gear head -inch (U.S.A.) B-449 Controls C-4 Option D-2
(Refer to page A-58 for connection of thermal protector.)
PP
UV
W
Change any two lead wires of U, V and W for CW rotation.CCW (counterclockwise)
W
V
U
P
P
R
S
T
White
Gray
BlackThermal protector
Blue
Blue TP
Terminal
Screws for earth
3-phase motor (sealed connector)
M9MZ60GK4YGM9MZ60GK4YGA
M9MZ60GK4CGM9MZ60GK4CGA
1.0 (142)
0.69 (97.7)
0.87 (123)
1.0 (142)
0.88 (125)
1.0 (142)
0.42 (59.5)
0.35 (49.6)
0.35 (49.6)
0.34 (48.1)
0.43 (60.9)
0.43 (60.9)
90 mmsq.
4
4
60
60
50
60
60
60
50
50
200
220
230
380
400
101
96
98
98
103
103
0.45
0.41
0.40
0.41
0.22
0.22
1350
1625
1650
1675
1325
1325
1.3
1.2
1.3
1.4
0.62
0.65
Cont.
Cont.
Motor model No.
Rating
SizeNumber
of pole
(P)
Output
(W)
Voltage
(V)
Frequency
(Hz)
Rating
(min)Input
(W)
Current
(A)
TorqueN·m
(oz-in)
Starting torque
N·m
(oz-in)
Starting
current
(A)Speed
(min–1)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
6002.53
5003
3.6
2506
7.2
30056
3604.25
7502
2.4
9001.72
10001.51.8
12001.31.5
15001
1.2
18000.81
0.98(8.7)
1.18(10.4)
1.57(13.9)
1.96(17.3)
2.35(20.8)
2.94(26.0)
3.14(27.8)
3.92(34.7)
4.70(41.6)
5.59(49.5)
6.27(55.5)
7.55(66.8)
9.11(80.6)
11.0(97.4)
15.2(135)
17.8(158)
19.6(173)
0.78(6.9)
0.98(8.7)
1.37(12.1)
1.57(13.9)
1.96(17.3)
2.35(20.8)
2.65(23.5)
3.33(29.5)
3.92(34.7)
4.70(41.6)
5.29(46.8)
6.47(57.3)
7.55(66.8)
9.11(80.6)
12.6(112)
15.2(135)
19.6(173)
3
500
600
3.6
416.7
500
5
300
360
6
250
300
7.5
200
240
9
166.7
200
10
150
180
12.5
120
144
15
100
120
18
83.3
100
20
75
90
25
60
72
30
50
60
36
41.7
50
50
30
36
60
25
30
75
20
24
90
16.7
20
100
15
18
120
12.5
15
180
8.3
10
200
7.5
9
150
10
12
Same as motor rotational directionReverse to motorrotational direction
• Permissible torque at output shaft of gear head using decimal gear head
MZ9G10XB
MZ9G B(ball bearing / hinge not attached)
MY9G B(ball bearing / hinge attached)
Applicable gear head
Bearing Decimalgear head
Speed(min–1)
Permissibletorque
50Hz60Hz
N·m(lb-in)
Rotational direction
Reduction ratio
Same as motor rotational direction Same as motor rotational directionReverse to motor rotational direction
50Hz60Hz
50Hz
60Hz
Reduction ratio
Rotational direction
Speed (min–1)
Unit of permissible torque: upper (N·m) / lower (lb-in)
MZ9G3B toMZ9G200B
MY9G3B toMY9G200B
Applicable gear head
ball bearing(hinge not attached)
ball bearing(hinge attached)
Connection diagram Speed-torque characteristics
00 1800
1.5
1.0
0.5
15001000500
60Hz 200V
50Hz 200V
(N·m)
Speed (min–1)
Tor
que
150
100
50
200
(oz-in)
M9MZ60GK4YG(A)
* Please read your User's manual carefully so that you will understand the operation and safety precautions before attempting to operate the system.
B-156
• Specifications
• Permissible torque at output shaft of gear head* The speed shown below is a calculated value based on the synchronous rotational speed. Depending on the load, the speed is less than the indicated value by 2 to 20%.
• The specifications and wire connections of the round shaft motor are the same as those of the pinion shaft type. For the dimensional outline drawing, refer to page B-165.
Model list B-128Coding system B-127System configuration B-127Features B-126
• The models with a motor model number to which “A” is suffixed are not sold or available in Japan.
Note) MZ / MY is available for a gear head of either type.
ø15
h7(ø
0.59
h7)
ø34
(ø1.
34) 12
(0.4
7)18
(0.7
1)
5(0.20)
90 mm sq.(3.54 inch sq.)
ø104(ø4.09)
4–ø7(ø0.28)
29(1.14)
25(0.98)
7(0.28)
60(2.36) 38(1.50)
5(0.
20)
ø34
(ø1.
34)
ø15
h7(ø
0.59
h7)
110(
4.33
)13
0(5.
12)
60(2.36)36(1.42)4–ø8.5
(ø0.33)
4–ø6.5(ø0.26)
60(2.36) 38(1.50)7(0.28)
29(1.14)
12(0.47)8(0.31)
25(0.98)
18(0.71)
12(0.47)
ø104
(ø4.09)
90 m
m s
q.(3
.54
inch
sq.
)
60(2
.36)
Gear head (dimensions) Scale: 1/4, Unit: mm (inch)
MZ9G B (ball bearing / hinge not attached) MY9G B (ball bearing / hinge attached)Mass 1.4 kg (3.09 lb) Mass 1.4 kg (3.09 lb)
Key and keyway(dimensions) [attachment]
25(0.98)
5 0 -0.
030
12 0
-0
.15
5 0
-0.030
0.20 0
-0.001
5+0.050
0
( )
0.20
0
-
0.00
1(
)
0.20+0.002
0( )
0.47
0
-0
.006
(
)
MZ9G BMY9G B
90 mm sq.(3.54 inch sq.)
75(2.95) 1(0.04)30(1.18)max.
4–ø6.5(ø0.26)
CCWCW
67(2.64)
155.5(6.12)135(5.31) 20.5(0.81)
7.5(0.30)40(1.57) 2(0.08)
ø85
h7
92 m
m s
q.
O-ring
(45(
1.77
))
(20(
0.79
))
(3.6
2 in
ch s
q.)
ø104(ø4.09)
(ø3.
35h7
)
Change any two lead wires of U, V and W for CW rotation.
R
S
T W
V
UWhite
Gray
Black
CCW(counterclockwise)
UV
W
Terminal
Screws for earth
3-phase motor (sealed connector)
90 mmsq. M9MZ90GK4Y
1.6 (227)
1.1 (156)
2.0 (283)
1.4 (198)
0.63 (89.2)
0.53 (75.1)
0.62 (87.8)
0.52 (73.6)
4 90
200
220
50
60
50
60
141
137
143
137
0.62
0.56
0.65
0.56
1350
1625
1400
1650
2.0
1.8
2.2
2.0
Cont.
Cont.
Motor model No.
Rating
SizeNumber
of pole
(P)
Output
(W)
Voltage
(V)
Frequency
(Hz)
Rating
(min)Input
(W)
Current
(A)
TorqueN·m
(oz-in)
Starting torque
N·m
(oz-in)
Starting
current
(A)Speed
(min–1)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
6002.53
5003
3.6
2506
7.2
30056
3604.25
7502
2.4
9001.72
10001.51.8
12001.31.5
15001
1.2
18000.81
1.18(10.4)
1.37(12.1)
1.86(16.5)
2.25(19.9)
2.84(25.1)
3.43(30.4)
3.72(32.9)
4.70(41.6)
5.68(50.3)
6.76(59.8)
7.55(66.8)
9.21(81.5)
10.9(96.5)
13.0(115)
18.3(162)
19.6(173)
1.37(12.1)
1.67(14.8)
2.25(19.9)
2.74(24.3)
3.43(30.4)
4.12(36.5)
4.51(39.9)
5.68(50.3)
6.76(59.8)
8.04(71.2)
9.02(79.8)
10.9(96.5)
13.0(115)
15.7(139)
19.6(173)
19.6(173)
3
500
600
3.6
416.7
500
5
300
360
6
250
300
7.5
200
240
9
166.7
200
10
150
180
12.5
120
144
15
100
120
18
83.3
100
20
75
90
25
60
72
30
50
60
36
41.7
50
50
30
36
60
25
30
75
20
24
90
16.7
20
100
15
18
120
12.5
15
180
8.3
10
200
7.5
9
150
10
12
Same as motor rotational directionReverse to motorrotational direction
• Permissible torque at output shaft of gear head using decimal gear head
MZ9G10XB
MZ9G B(ball bearing / hinge not attached)
MY9G B(ball bearing / hinge attached)
Applicable gear head
Bearing Decimalgear head
Speed(min–1)
Permissibletorque
50Hz60Hz
N·m(lb-in)
Rotational direction
Reduction ratio
Same as motor rotational direction Same as motor rotational directionReverse to motor rotational direction
50Hz60Hz
50Hz
60Hz
Reduction ratio
Rotational direction
Speed (min–1)
Unit of permissible torque: upper (N·m) / lower (lb-in)
MZ9G3B toMZ9G200B
MY9G3B toMY9G200B
Applicable gear head
ball bearing(hinge not attached)
ball bearing(hinge attached)
Connection diagram Speed-torque characteristics
0
0.5
2.0
2.5
1.5
1.0
0 180015001000500
50Hz 200V
50Hz 220V
60Hz 200V60Hz 220V
(N·m)
Speed (min–1)
Tor
que
(oz-in)
200
100
300
M9MZ90GK4Y
M9MZ90GK4Y 4P 90 W 200 V / 220 V (with fan)
* Please read your User's manual carefully so that you will understand the operation and safety precautions before attempting to operate the system. (Note) Because the dimensions may be subject to change, also check the determinate dimensions if the gear head is to be used for design.
B-158 B-159
• Specifications
• Permissible torque at output shaft of gear head* The speed shown below is a calculated value based on the synchronous rotational speed. Depending on the load, the speed is less than the indicated value by 2 to 20%.
• The specifications and wire connections of the round shaft motor are the same as those of the pinion shaft type. For the dimensional outline drawing, refer to page B-165.
* Diameter of applicable cabtyre cable to be ø8(ø0.31) to ø12(ø0.47).
Helical
gear
Module
0.6Numberof teeth
9
Mass3.3 kg7.28 lb
Model list B-128Coding system B-127System configuration B-127Features B-126
Ind
uctio
nm
oto
rR
eversible
mo
tor
3-ph
asem
oto
rE
lectrom
agn
eticb
rakem
oto
rV
ariable
speed
ind
uctio
nm
oto
rV
ariable
speed
reversible
mo
tor
Variable
speedelectrom
agneticbrake
single-phasem
otorV
ariable
speed
un
itm
oto
rC
&B
mo
tor
2-poleround
shaftm
oto
rG
earh
eadG
earh
ead-in
ch(U
.S.A
.)90mm (3.54inch) sq. 90 W
Motor (dimensions) Scale: 1/4, Unit: mm (inch)
Gear head combination B-163 Round shaft motor B-165 Decimal gear head B-448 Gear head -inch (U.S.A.) B-449 Controls C-4 Option D-2
Note) MZ / MY is available for a gear head of either type.
ø15
h7(ø
0.59
h7)
ø34
(ø1.
34) 12
(0.4
7)18
(0.7
1)
5(0.20)
90 mm sq.(3.54 inch sq.)
ø104(ø4.09)
4–ø7(ø0.28)
29(1.14)
25(0.98)
7(0.28)
60(2.36) 38(1.50)
5(0.
20)
ø34
(ø1.
34)
ø15
h7(ø
0.59
h7)
110(
4.33
)13
0(5.
12)
60(2.36)36(1.42)4–ø8.5
(ø0.33)
4–ø6.5(ø0.26)
60(2.36) 38(1.50)7(0.28)
29(1.14)
12(0.47)8(0.31)
25(0.98)
18(0.71)
12(0.47)
ø104
(ø4.09)
90 m
m s
q.(3
.54
inch
sq.
)
60(2
.36)
Gear head (dimensions) Scale: 1/4, Unit: mm (inch)
MZ9G B (ball bearing / hinge not attached) MY9G B (ball bearing / hinge attached)Mass 1.4 kg (3.09 lb) Mass 1.4 kg (3.09 lb)
Key and keyway(dimensions) [attachment]
25(0.98)
5 0 -0.
030
12 0
-0
.15
5 0
-0.030
0.20 0
-0.001
5+0.050
0
( )
0.20
0
-
0.00
1(
)
0.20+0.002
0( )
0.47
0
-0
.006
(
)
MZ9G BMY9G B
90 mm sq.(3.54 inch sq.)
75(2.95) 1(0.04)30(1.18)max.
4–ø6.5(ø0.26)
CCWCW
67(2.64)
155.5(6.12)135(5.31) 20.5(0.81)
7.5(0.30)40(1.57) 2(0.08)
ø85
h7
92 m
m s
q.
O-ring
(45(
1.77
))
(20(
0.79
))
(3.6
2 in
ch s
q.)
ø104(ø4.09)
(ø3.
35h7
)
(Refer to page A-58 for connection of thermal protector.)
PP
UV
W
Change any two lead wires of U, V and W for CW rotation.CCW (counterclockwise)
W
V
U
P
P
R
S
T
White
Gray
BlackThermal protector
Blue
Blue TP
Terminal
Screws for earth
3-phase motor (sealed connector)
M9MZ90GK4YGM9MZ90GK4YGA
M9MZ90GK4CGM9MZ90GK4CGA
1.6 (227)
1.1 (156)
1.4 (198)
1.6 (227)
1.4 (198)
1.6 (227)
0.63 (89.2)
0.53 (75.1)
0.52 (73.6)
0.51 (72.2)
0.65 (92.0)
0.64 (90.6)
90 mmsq.
4
4
90
90
50
60
60
60
50
50
200
220
230
380
400
142
138
137
137
144
144
0.62
0.56
0.56
0.58
0.31
0.31
1350
1625
1650
1675
1325
1350
2.0
1.8
2.0
2.1
1.0
1.0
Cont.
Cont.
Motor model No.
Rating
SizeNumber
of pole
(P)
Output
(W)
Voltage
(V)
Frequency
(Hz)
Rating
(min)Input
(W)
Current
(A)
TorqueN·m
(oz-in)
Starting torque
N·m
(oz-in)
Starting
current
(A)Speed
(min–1)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
19.6
(173)
6002.53
5003
3.6
2506
7.2
30056
3604.25
7502
2.4
9001.72
10001.51.8
12001.31.5
15001
1.2
18000.81
1.18(10.4)
1.37(12.1)
1.86(16.5)
2.25(19.9)
2.84(25.1)
3.43(30.4)
3.72(32.9)
4.70(41.6)
5.68(50.3)
6.76(59.8)
7.55(66.8)
9.21(81.5)
10.9(96.5)
13.0(115)
18.3(162)
19.6(173)
1.37(12.1)
1.67(14.8)
2.25(19.9)
2.74(24.3)
3.43(30.4)
4.12(36.5)
4.51(39.9)
5.68(50.3)
6.76(59.8)
8.04(71.2)
9.02(79.8)
10.9(96.5)
13.0(115)
15.7(139)
19.6(173)
19.6(173)
3
500
600
3.6
416.7
500
5
300
360
6
250
300
7.5
200
240
9
166.7
200
10
150
180
12.5
120
144
15
100
120
18
83.3
100
20
75
90
25
60
72
30
50
60
36
41.7
50
50
30
36
60
25
30
75
20
24
90
16.7
20
100
15
18
120
12.5
15
180
8.3
10
200
7.5
9
150
10
12
Same as motor rotational directionReverse to motorrotational direction
• Permissible torque at output shaft of gear head using decimal gear head
MZ9G10XB
MZ9G B(ball bearing / hinge not attached)
MY9G B(ball bearing / hinge attached)
Applicable gear head
Bearing Decimalgear head
Speed(min–1)
Permissibletorque
50Hz60Hz
N·m(lb-in)
Rotational direction
Reduction ratio
Same as motor rotational direction Same as motor rotational directionReverse to motor rotational direction
50Hz60Hz
50Hz
60Hz
Reduction ratio
Rotational direction
Speed (min–1)
Unit of permissible torque: upper (N·m) / lower (lb-in)
MZ9G3B toMZ9G200B
MY9G3B toMY9G200B
Applicable gear head
ball bearing(hinge not attached)
ball bearing(hinge attached)
Connection diagram Speed-torque characteristics
00 1800
2.0
1.5
1.0
0.5
15001000500
200V 60Hz
200V 50Hz
(N·m)
Speed (min–1)
Tor
que
(oz-in)
100
200
M9MZ90GK4YG(A)
M9MZ90GK4YG(A)M9MZ90GK4CG(A)
4P 90 W 200 V / 220 V / 230 V (with fan) 4P 90 W 380 V / 400 V (with fan)
* Diameter of applicable cabtyre cable to be ø8(ø0.31) to ø12(ø0.47).
* Please read your User's manual carefully so that you will understand the operation and safety precautions before attempting to operate the system. (Note) Because the dimensions may be subject to change, also check the determinate dimensions if the gear head is to be used for design.
B-160 B-161
• Specifications
• Permissible torque at output shaft of gear head* The speed shown below is a calculated value based on the synchronous rotational speed. Depending on the load, the speed is less than the indicated value by 2 to 20%.
• The specifications and wire connections of the round shaft motor are the same as those of the pinion shaft type. For the dimensional outline drawing, refer to page B-165.
Helical
gear
Module
0.6Numberof teeth
9
Mass3.3 kg7.28 lb
Model list B-128Coding system B-127System configuration B-127Features B-126
Ind
uctio
nm
oto
rR
eversible
mo
tor
3-ph
asem
oto
rE
lectrom
agn
eticb
rakem
oto
rV
ariable
speed
ind
uctio
nm
oto
rV
ariable
speed
reversible
mo
tor
Variable
speedelectrom
agneticbrake
single-phasem
otorV
ariable
speed
un
itm
oto
rC
&B
mo
tor
2-poleround
shaftm
oto
rG
earh
eadG
earh
ead-in
ch(U
.S.A
.)90mm (3.54inch) sq. 90 W
Motor (dimensions) Scale: 1/4, Unit: mm (inch)
Gear head combination B-163 Round shaft motor B-165 Decimal gear head B-448 Gear head -inch (U.S.A.) B-449 Controls C-4 Option D-2
• The models with a motor model number to which “A” is suffixed are not sold or available in Japan.
Note) MZ / MY is available for a gear head of either type.
ø15
h7(ø
0.59
h7)
ø34
(ø1.
34) 12
(0.4
7)18
(0.7
1)
5(0.20)
90 mm sq.(3.54 inch sq.)
ø104(ø4.09)
4–ø7(ø0.28)
29(1.14)
25(0.98)
7(0.28)
60(2.36) 38(1.50)
5(0.
20)
ø34
(ø1.
34)
ø15
h7(ø
0.59
h7)
110(
4.33
)13
0(5.
12)
60(2.36)36(1.42)4–ø8.5
(ø0.33)
4–ø6.5(ø0.26)
60(2.36) 38(1.50)7(0.28)
29(1.14)
12(0.47)8(0.31)
25(0.98)
18(0.71)
12(0.47)
ø104
(ø4.09)
90 m
m s
q.(3
.54
inch
sq.
)
60(2
.36)
Gear head (dimensions) Scale: 1/4, Unit: mm (inch)
MZ9G B (ball bearing / hinge not attached) MY9G B (ball bearing / hinge attached)Mass 1.4 kg (3.09 lb) Mass 1.4 kg (3.09 lb)
Key and keyway(dimensions) [attachment]
25(0.98)
5 0 -0.
030
12 0
-0
.15
5 0
-0.030
0.20 0
-0.001
5+0.050
0
( )
0.20
0
-
0.00
1(
)
0.20+0.002
0( )
0.47
0
-0
.006
(
)
MZ9G BMY9G B
Specifications B-130 to B-161 Option D-2Controls C-4
Ind
uctio
nm
oto
rR
eversible
mo
tor
3-ph
asem
oto
rE
lectrom
agn
eticb
rakem
oto
rV
ariable
speed
ind
uctio
nm
oto
rV
ariable
speed
reversible
mo
tor
Variable
speedelectrom
agneticbrake
single-phasem
otorV
ariable
speed
un
itm
oto
rC
&B
mo
tor
2-poleround
shaftm
oto
rG
earh
eadG
earh
ead-in
ch(U
.S.A
.)3-phase motor (sealed connector)
(Note) Because the dimensions may be subject to change, also check the determinate dimensions if the gear head is to be used for design.
B-163
3-phase motor (leadwire)
* Please read your User's manual carefully so that you will understand the operation and safety precautions before attempting to operate the system.
B-162 Model list B-128Coding system B-127System configuration B-127Features B-126
+ MX8G B(M)+ MX8G B(M)
M8MX25G4YM8MX25G4YG(A)
115(4.53)
85(3.35)
7(0.28)
ø10
h7(ø
0.39
h7)
ø30
(ø1.
18)
30(1.18)
32(1.26)
25(0.98)6
(0.24)
Motor leadwires300±30 mm (11.8±1.18 inch)
AWG20
MA
Xø
86(ø
3.39
)+ MX9G B(M)+ MX9G B(M)
M9MX40G4YM9MX40G4YG(A)
142(5.59)
105(4.13)7.5(0.30)
Motor leadwires300±30 mm (11.8±1.18 inch)
AWG20
MA
Xø
95(ø
3.74
)
ø12
h7(ø
0.47
)
ø36
(ø1.
42)
37(1.46)
32(1.26)
25(0.98)5(0.20)
+ MZ9G B (MY9G B)+ MZ9G B (MY9G B)
M9MZ60G4YM9MZ60G4YG(A)
180(7.09)
120(4.72)7.5(0.30)40(1.57)
Motor leadwires300±30 mm (11.8±1.18 inch)
AWG20
92 m
m s
q.(3
.62
inch
sq.
)
ø15
h7(ø
0.59
h7)
ø34
(ø1.
34)
29(1.14)
25(0.98)
7(0.28)
60(2.36)
38(1.50)
+ MY9G B (MZ9G B)+ MY9G B (MZ9G B)
M9MZ90G4YM9MZ90G4YG(A)
195(7.68)
135(5.31)
7.5(0.30)40(1.57)
92 m
m s
q.(3
.62
inch
sq.
)
Motor leadwires300±30 mm (11.8±1.18 inch)
AWG20
ø34
(ø1.
34)
ø15
h7(ø
0.59
h7)60(2.36)
38(1.50)
7(0.28)
29(1.14)
12(0.47)8(0.31)
25(0.98)
+ MX8G B(M)+ MX8G B(M)+ MX8G B(M)
M8MX25GK4YM8MX25GK4YG(A)M8MX25GK4CG(A)
96.3(3.79)
85(3.35)
75(2.95) 1(0.04)30(1.18)max.
7(0.28)
MA
Xø
86(ø
3.39
)(2
0(0.
79))
(45(
1.77
))
ø10
h7(ø
0.39
h7)
ø30
(ø1.
18)
30(1.18)
32(1.26)
25(0.98)
6(0.24)
+ MX9G B(M)+ MX9G B(M)+ MX9G B(M)
M9MX40GK4YM9MX40GK4YG(A)M9MX40GK4CG(A)
(45(
1.77
))
142(5.59)
105(4.13)
7.5(0.30)
75(2.95) 1(0.04)30(1.18)max.
MA
Xø
95(ø
3.74
)(2
0(0.
79))
ø12
h7(ø
0.47
)
ø36
(ø1.
42)
37(1.46)
32(1.26)
25(0.98)
5(0.20)
+ MZ9G B (MY9G B)+ MZ9G B (MY9G B)+ MZ9G B (MY9G B)
M9MZ60GK4YM9MZ60GK4YG(A)M9MZ60GK4CG(A)
75(2.95) 1(0.04)30(1.18)max.
180(7.09)120(4.72)
7.5(0.30)40(1.57)
92 m
m s
q.(3
.62
inch
sq.
)
(45(
1.77
))
(20(
0.79
))
ø15
h7(ø
0.59
h7)
ø34
(ø1.
34)
29(1.14)
25(0.98)7(0.28)
60(2.36)38(1.50)
* Diameter of applicable cabtyre cable to be ø8(ø0.31) to ø12(ø0.47).
* Refer to page B-444 for high torque gear head.
* Refer to page B-444 for high torque gear head. * Refer to page B-444 for high torque gear head.
* Diameter of applicable cabtyre cable to be ø8(ø0.31) to ø12(ø0.47). * Diameter of applicable cabtyre cable to be ø8(ø0.31) to ø12(ø0.47).
+ MY9G B (MZ9G B)+ MY9G B (MZ9G B)+ MY9G B (MZ9G B)
M9MZ90GK4YM9MZ90GK4YG(A)M9MZ90GK4CG(A)
75(2.95) 1(0.04)30(1.18)max.
195(7.68)135(5.31)
40(1.57)
92 m
m s
q.(3
.62
inch
sq.
)
(45(
1.77
))
(20(
0.79
))
ø34
(ø1.
34)
ø15
h7(ø
0.59
h7)
60(2.36)
38(1.50)
7(0.28)
29(1.14)
12(0.47)8(0.31)
25(0.98)
7.5(0.30)
* Diameter of applicable cabtyre cable to be ø8(ø0.31) to ø12(ø0.47).
* Refer to page B-444 for high torque gear head.
Gear head combination dimensionsScale: 1/4, Unit: mm (inch)
Gear head combination dimensionsScale: 1/4, Unit: mm (inch)
*The models with a motor model number to which “A” is suffixed are not sold or available in Japan.
80 mm sq. (3.15 inch sq.) 25 W
90 mm sq. (3.54 inch sq.) 60 W
90 mm sq. (3.54 inch sq.) 40 W
90 mm sq. (3.54 inch sq.) 90 W
80 mm sq. (3.15 inch sq.) 25 W
90 mm sq. (3.54 inch sq.) 60 W
90 mm sq. (3.54 inch sq.) 40 W
90 mm sq. (3.54 inch sq.) 90 W
Specifications B-130 to B-161 Option D-2Controls C-4
Ind
uctio
nm
oto
rR
eversible
mo
tor
3-ph
asem
oto
rE
lectrom
agn
eticb
rakem
oto
rV
ariable
speed
ind
uctio
nm
oto
rV
ariable
speed
reversible
mo
tor
Variable
speedelectrom
agneticbrake
single-phasem
otorV
ariable
speed
un
itm
oto
rC
&B
mo
tor
2-poleround
shaftm
oto
rG
earh
eadG
earh
ead-in
ch(U
.S.A
.)
(Note) Because the dimensions may be subject to change, also check the determinate dimensions if the gear head is to be used for design.
B-165
3-phase motor (4-pole round shaft / leadwire)
* Please read your User's manual carefully so that you will understand the operation and safety precautions before attempting to operate the system.
B-164 Model list B-128Coding system B-127System configuration B-127Features B-126
M8MX25S4YSM8MX25S4YG(A)
Motor leadwires300±30 mm (11.8±1.18 inch)
AWG20
ø73
h7(ø
2.87
h7)
MA
Xø
86(ø
3.39
)
85(3.35) 32(1.26)7(0.28) 3(0.12)
80 mm sq.(3.15 inch sq.)
CWCCW
25(0.98)
ø8h
7(ø
0.31
h7)
7(0.
28)
ø94(ø3.70)
4–ø5.5(ø0.22)
M9MX40S4YSM9MX40S4YG(A)
105(4.13) 37(1.46)7.5(0.30) 3(0.12)
ø83
h7(ø
3.27
h7)
90 mm sq.(3.54 inch sq.)
CWCCW
Motor leadwires300±30 mm (11.8±1.18 inch)
AWG20
30(1.18)
ø10
h7(ø
0.39
h7)
9(0.
35)
MA
Xø
95(ø
3.74
)
4–ø6.5(ø0.26)ø104(ø4.09)
M9MZ60S4YS (with fan)M9MZ60S4YG(A) (with fan)
120(4.72) 37(1.46)7.5(0.30)40(1.57) 3(0.12)
ø83
h7(ø
3.27
h7)
90 mm sq.(3.54 inch sq.)
CWCCW
Motor leadwires300±30 mm (11.8±1.18 inch)
AWG20
92 m
m s
q.(3
.62
inch
sq.
)
30(1.18)
ø12
h7(ø
0.47
h7)
11(0
.43)
4–ø6.5(ø0.26)ø104(ø4.09)
M9MZ90S4YS (with fan)M9MZ90S4YG(A) (with fan)
4–ø6.5(ø0.26)
CWCCW
92 m
m s
q.(3
.62
inch
sq.
)
Motor leadwires300±30 mm (11.8±1.18 inch)
AWG20
90 mm sq.(3.54 inch sq.)
135(5.31) 37(1.46)7.5(0.30)40(1.57) 3(0.12)
ø83
h7(ø
3.27
h7)
30(1.18)
ø12
h7(ø
0.47
h7)
11(0
.43)
ø104(ø4.09)
M9MZ60SK4YS (with fan)M9MZ60SK4YG(A) (with fan)M9MZ60SK4CG(A) (with fan)
75(2.95) 1(0.04)30(1.18)max.
CCWCW
67(2.64)
120(4.72) 37(1.46)
7.5(0.30)40(1.57) 3(0.12)
ø83
h7(ø
3.27
h7)
92 m
m s
q.(3
.62
inch
sq.
)
30(1.18)
ø12
h7(ø
0.47
h7)
11(0
.43)
(45(
1.77
))
(20(
0.79
))
4–ø6.5(ø0.26)
90 mm sq.(3.54 inch sq.)
ø104(ø4.09)
M9MZ90SK4YS (with fan)M9MZ90SK4YG(A) (with fan)M9MZ90SK4CG(A) (with fan)
90 mm sq.(3.54 inch sq.)
ø104
(ø4.09)
75(2.95) 1(0.04)30(1.18)max.
CCWCW
67(2.64)
135(5.31) 37(1.46)
7.5(0.30)40(1.57) 3(0.12)
ø83
h7(ø
3.27
h7)
92 m
m s
q.(3
.62
inch
sq.
)
30(1.18)
ø12
h7(ø
0.47
h7)
11(0
.43)
(45(
1.77
))
(20(
0.79
))
4–ø6.5(ø0.26)
M8MX25SK4YS M8MX25SK4YG(A)M8MX25SK4CG(A)
85(3.35)
75(2.95) 1(0.04)30(1.18)max.
32(1.26)
7(0.28) 3(0.12)
ø73
h7(ø
2.87
h7)
4–ø5.5(ø0.22)
CCWCW
67(2.64)
25(0.98)
øø
8h7
(ø0.
31h7
)
7(0.
28)
MA
Xø
86(ø
3.39
)
(45(
1.77
))
(20(
0.79
))
80 mm sq.(3.15 inch sq.)
ø94(ø3.70)
M9MX40SK4YS M9MX40SK4YG(A)M9MX40SK4CG(A)
ø83
h7(ø
3.27
h7)
105(4.13) 37(1.46)
7.5(0.30) 3(0.12)
75(2.95) 1(0.04)30(1.18)max.
CCWCW
67(2.64)
30(1.18)
ø10
h7(ø
0.39
h7)
9(0.
35)
(45(
1.77
))
(20(
0.79
))M
AX
ø95
(ø3.
74)
4–ø6.5(ø0.26)
90 mm sq.(3.54 inch sq.)
ø104(ø4.09)
3-phase motor (4-pole round shaft / sealed connector) DimensionsScale: 1/4, Unit: mm (inch)
DimensionsScale: 1/4, Unit: mm (inch)
* Diameter of applicable cabtyre cable to be ø8(ø0.31) to ø12(ø0.47). * Diameter of applicable cabtyre cable to be ø8(ø0.31) to ø12(ø0.47).
* Diameter of applicable cabtyre cable to be ø8(ø0.31) to ø12(ø0.47). * Diameter of applicable cabtyre cable to be ø8(ø0.31) to ø12(ø0.47).
200 V/220 V/230 V round shaft motors with a sealed connector (with a terminal box) are covered by the Electrical Appliance and Material Safety Law. The indications on their nameplate are based on this law.
*The models with a motor model number to which “A” is suffixed are not sold or available in Japan.
Mass1.5 kg (3.31 lb)80 mm sq. (3.15 inch sq.) 25 W Mass
2.4 kg (5.29 lb)90 mm sq. (3.54 inch sq.) 40 W
Mass2.7 kg (5.95 lb)90 mm sq. (3.54 inch sq.) 60 W Mass
3.2 kg (7.05 lb)90 mm sq. (3.54 inch sq.) 90 W
Mass1.8 kg (3.97 lb)80 mm sq. (3.15 inch sq.) 25 W Mass
2.8 kg (6.17 lb)90 mm sq. (3.54 inch sq.) 40 W
Mass3.0 kg (6.61 lb)90 mm sq. (3.54 inch sq.) 60 W Mass
3.3 kg (7.28 lb)90 mm sq. (3.54 inch sq.) 90 W