QEMU Binary Translation Ashish Kaila (akaila) Maneet Singh (maneets) 1.
2D TO 3D MODELLING KCCOE PROJECT PRESENTATION Student: Ashish Nikam Ashish Singh Samir Gaykar Sanoj...
-
Upload
meryl-willis -
Category
Documents
-
view
222 -
download
0
Transcript of 2D TO 3D MODELLING KCCOE PROJECT PRESENTATION Student: Ashish Nikam Ashish Singh Samir Gaykar Sanoj...
2D TO 3D MODELLING
KCCOE
PROJECT PRESENTATION
Student: Ashish Nikam Ashish Singh Samir Gaykar Sanoj SinghGuidence: Prof. Ashwini Jaywant
Submitted by ---
INTROUCTION
3D models are obtained from 2D views.
2D images which are scanned using laser are captured using webcam which determines depth of each pixel and then this image is converted into surface image.
The processed images are then placed on the visual platform thus giving us a 3D model of the object that was captured by the camera.
EXISTING METHOD FOR 3D MODELLING
TriangulationLaser on the object A camera looks for the location of the laser dot. Laser dot, camera and laser emitter form a triangle.
Time-of-flightLaser rangefinder: distance to the first object on its path is measured. Laser: emits a pulse of light. Detector: reflected light is seen. Timing the round-trip time of a pulse of light.
Handheld LaserA laser dot or line is projected onto an object.Handheld laser device and a sensor is applied.Position of the scanner is recorded (laser tracker).
Stereoscopic Human stereoscopic vision based.Two video cameras are arranged.Differences between the images seen by each camera.Determine the distance at each point in the images.
PhotometricSingle cameraMultiple images under varying lighting conditions.Surface orientation at each pixel.
SilhouettePhotos are taken around an object against a background.Outlines created from a sequence of photos. Silhouettes are extruded and intersected.Visual hull approximation of the object. Some concavities are not detected.
OUR APPROACH This project aims at providing a 3D image using nothing more
than a simple image capturing device [a high resolution webcam] and a rotating platform on which the object is mounted. The rotation of this platform is to be controlled by a microcontroller and a stepper motor. The rotation occurs in discrete steps which are programmed at the micro controller. The resolution of the 3D image depends on the number of images which are used to reconstruct it. Therefore the degree of rotation is a control for the 3D image resolution.
Once the images are captured they have to be stored sequentially on the computer using the USB interface. The webcam image capture is closely synchronized with the rotation of the platform so that the image is captured at the exact moment when the platform is stationary. The images from different angles are then used to reconstruct a 3D image. Image stitching algorithms perform this task.
The proposed project is an attempt at providing a low cost portable alternative to the existing techniques that provide similar results. Special attention has been paid to reduce the tradeoff between details and the time required thus satisfying a wide spectrum of needs.
FLOW CHART
HARDWARE & SOFTWARE
Computer Microcontroller (89C51) Stepper motor and motor
controller (ULN2003) RS232 cable Webcam MATLAB Software based image
processing using laser scanning
BLOCK DIAGRAM
RS232
CAMERA
MICROCONTROLLER (ATMEGA 8)
MOTOR CONTROLLER (ULN2003)
SERVO MOTOR
Camera
Laser
(x,y)
Object
A camera looks for the location of the laser dot.
Laser dot, camera and laser emitter form a triangle
OPERATION: EDGE DETECTION
Figure 1
Figure 2
Click to edit the outline text format
Second Outline Level
Third Outline Level
Fourth Outline Level Fifth Outline Level Sixth Outline Level
Seventh Outline LevelClick to edit Master text styles
Second level Third level
Fourth level
Fifth level
CANNY EDGE DETECTION
1. smooth
2. gradient
3. thresh, suppress, link
Edge is Where Change Occurs
THE CANNY EDGE DETECTOR
2: Norm Of The Gradient1: Original Image (Lena)
3: Thresholding4: Thinning
(Non-maximum Suppression)
FINAL IMPLENEMTATION
Reconstructed 3D image
ADVANTAGES & APPLICATIONS
The medical industry uses detailed models of organs. The movie industry uses them as characters and objects for
animated and real-life motion pictures. The video game industry uses them as assets for
computer and video games. The science sector uses them as highly detailed models of
chemical compounds. The architecture industry uses them to demonstrate proposed
buildings and landscapes through Software Architectural Models.
The engineering community uses them as designs of new devices, vehicles and structures as well as a host of other uses.
In recent decades the earth science community has started to construct 3D geological models as a standard practice.
FUTURE SCOPE Replacing the turntable with an
improved model. Increasing the laser fan angle from 60. Replacing the camera with one that
allows for turning automatic gain off. Reduce noise and blooming.
Improve image acquisition and processing software user interface.
REFERENCES
http://en.wikipedia.org/wiki/3D_scanner
http://courses.cit.cornell.edu/ee476/FinalProjects/s2009/dat38/Website/index.htm
http://www.owlnet.rice.edu/~elec539/Projects97/morphjrks/laplacian.html
http://sites.google.com/site/elsamuko/gimp/gimp-octave
QUESTIONS?