2” Retro Frame with Cover3-3/4” 2-3/8” Features & Benefits The 2” Retro Frame is designed to...
Transcript of 2” Retro Frame with Cover3-3/4” 2-3/8” Features & Benefits The 2” Retro Frame is designed to...
![Page 1: 2” Retro Frame with Cover3-3/4” 2-3/8” Features & Benefits The 2” Retro Frame is designed to fit over an existing sign or support structure. It will tension any size flexible](https://reader034.fdocuments.us/reader034/viewer/2022042916/5f582fbb122f5a0a7d553b93/html5/thumbnails/1.jpg)
C O M M E R C I A L E X T R U S I O N S
Features & Benefits
PartNumber Length
21122115
2” Retro Frame2-3/8” Retro Frame Cover
Part
24’-5”24’-5”
Finish
Mill FinishMill Finish
·Retro fits to new or existing cabinets·Easily assembles with structural corner angles·Designed to accept optional frame support·Easily accommodates the Dual Divider and Cover Part #’s 2142 and 2146
3032 Walker Ridge Dr. NW Grand Rapids, MI Phone: (616) 784-0405 Toll Free: (877) 784-0405 Fax: (616) 784-0411
2” Retro Frame with Cover
C O M M E R C I A L E X T R U S I O N S
Part #2115
2” Retro FramePart #2112
2-3/8” Retro Frame Cover
Part #2115
Tension ClipPart #5360
Flexible Face Material
Cover ScrewPart #5195
Frame Corner Angle Slot
C O M M E R C I A L E X T R U S I O N S
Part #2112
3.26
2.142.38
3.75
![Page 2: 2” Retro Frame with Cover3-3/4” 2-3/8” Features & Benefits The 2” Retro Frame is designed to fit over an existing sign or support structure. It will tension any size flexible](https://reader034.fdocuments.us/reader034/viewer/2022042916/5f582fbb122f5a0a7d553b93/html5/thumbnails/2.jpg)
See page 13, 15 & 37 in the Gold Commercial Catalog for more details.
1-1/8”2-1/4”
3-3/4”
2-3/8”
Features & BenefitsThe 2” Retro Frame is designed to fit over an existing sign or support structure. It will tension any size flexible face or banner material. The Tension Clips are easy to use and are re-useable. Eliminates hemming, grommets and double faced tape. The Dual Divider & Cover can be used to divide the flexible face into panels or transition from a flexible face to a rigid face.
Answers to FAQ’sAccepts any flexible face material.Face material trim size - Add 1-1/2” of fabric to all four sides. (Adding a total of 3” to both the height and width)Tension Clip placement - Tension Clips are placed approximately 1-1/2” from the edge of the trimmed to size face material.Tension Clip spacing - Every 6” on center.The correct Tension Tool to use with the frame is Part # 5135. Frame Support Tube and Frame Brace assemblies may be required if the existing sign or sub-structure is not structural enough to support the tension and wind loads.
h
h
h
h
h
h
2” Retro Frame - Part #21122-3/8” Retro Frame Cover - Part #2115Kit Designation - K2112/15
FAQ 2112/15
For further assistance please contact SignComp Customer Service Toll Free (877) 784-0405 Phone (616) 784-0405 Fax (616) 784-0411 [email protected] www.signcomp.com