2706-NC13, 2711-NC13 -NC14 : Cable Pinouts (Wiring Diagram) Straig... http://rockwellautomation.custhelp.com/cgi-bin/rockwellautomation.cfg/...

1 of 2 7/17/2008 8:01 PM

Support Home Answers My Stuff Login Help

Login is required to access additional content and features.

Search by Product

AllAll

Search by Category

AllAll

Search Tips

Search

Search By

PhrasesPhrases

ID

13488

Products

EOI

PanelView

PanelView Plus

PanelView Plus CE

VersaView CE

Category

General

Date Created

11/01/1995 12:00 AM

Last Updated

01/23/2008 01:52 AM

Access Level

Everyone

Prev. TN#

G13532

Print Answer

Email Answer

2706-NC13, 2711-NC13 -NC14 : Cable Pinouts (Wiring Diagram) Straight ThroughSerial Cable

Question

Cable diagram.

Answer

Cable diagram:

Female DB-9 Female DB-9

Connector Connector

DCD 1 -------------- 1 DCD

TXD 2 -------------- 2 RXD

RXD 3 -------------- 3 TXD

DTR 4 -------------- 4 DTR

COM 5 -------------- 5 COM

DSR 6 6 DSR

RTS 7 -------------- 7 RTS

CTS 8 -------------- 8 CTS

9 9

Cable shield is grounded through connector shells.

The following cables are interchangeable:

2706-NC13 10.0 feet 3 meter 2711-NC13 16.4 feet 5 meter 2711-NC14 32.7 feet 10 meter

Catalog Number: 2711NC13, 2711NC14, 2706NC13 DocFullNum: G13532

DISCLAIMERThis knowledge base web site is intended to provide general technical information on a particular subject or subjects and is not an exhaustive treatment of such subjects. Accordingly, the information in this web site is not intended to constitute application, design, software or other professional engineering advice or services. Before making any decision or taking any action, which might affect your equipment, you should consult a qualified professional advisor.

ROCKWELL AUTOMATION DOES NOT WARRANT THE COMPLETENESS, TIMELINESS OR ACCURACY OF ANY OF THE DATA CONTAINED IN THIS WEB SITE AND MAY MAKE CHANGES THERETO AT ANY TIME IN ITS SOLE DISCRETION WITHOUT NOTICE. FURTHER, ALL INFORMATION CONVEYED HEREBY IS PROVIDED TO USERS "AS IS." IN NO EVENT SHALL ROCKWELL BE LIABLE FOR ANY DAMAGES OF ANY KIND INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS PROFIT OR DAMAGE, EVEN IF ROCKWELL AUTOMATION HAVE

2711-NC13

2706-NC13, 2711-NC13 -NC14 : Cable Pinouts (Wiring Diagram) Straig... http://rockwellautomation.custhelp.com/cgi-bin/rockwellautomation.cfg/...

2 of 2 7/17/2008 8:01 PM

BEEN ADVISED ON THE POSSIBILITY OF SUCH DAMAGES.

ROCKWELL AUTOMATION DISCLAIMS ALL WARRANTIES WHETHER EXPRESSED OR IMPLIED IN RESPECT OF THE INFORMATION (INCLUDING SOFTWARE) PROVIDED HEREBY, INCLUDING THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, AND NON-INFRINGEMENT. Note that certain jurisdictions do not countenance the exclusion of implied warranties; thus, this disclaimer may not apply to you.

Copyright © 2006-2008 Rockwell Automation. All rights reserved.

Add this answer to my Favorite Answers

How well did this answer your question?

100% 75% 50% 25% 0% Submit Rating

Users who viewed this answer have also viewed

Back to Search Results

• 2711-NC21 and 2711-NC22 cables for the PanelView.

• RS 232 Communications cables.

• Standard Panelview protocol, cables, drivers and network connections.

• 2707-NC13 is Obsolete. What replacement cable for the 193-PCT hand held

programmer can be used instead of the 2707-NC13?

• AutoMax serial cable and serial port pinouts