25-Jul-2007 OF LIQUID CRYSTAL DISPLAY MODULE CUSTOMER … · [Note 7] Definition of Measurement of...
Transcript of 25-Jul-2007 OF LIQUID CRYSTAL DISPLAY MODULE CUSTOMER … · [Note 7] Definition of Measurement of...
SPECIFICATION
LIQUID CRYSTAL DISPLAY MODULE
CUSTOMER :
Model No. :
Model version : 0
Document Revision : 4
This specification need to be signed by purchaser or customer as a specification of productsproduction and delivery from URT. Without signature of this specification , any purchaseorder for this model no. will be treated and considered that this specification is automaticallyacknowledged and accepted by purchaser or customer.
UNITED RADIANT TECHNOLOGY CORPORATION
George Tseng Date
COMPANY : No. 2,Fu-hsing Road,Taichung Econamic Processing Zone,Tantzu,Taichung,Taiwan,R.O.C.
TEL: 886-4-25314277 FAX: 886-4-25313067
SALES OFFICE : 6F,No.17,Lane 360,Sec.1,Neihu Road,Neihu District,Taipei,Taiwan,R.O.C.
TEL: 886-2-27971088 FAX: 886-2-27970727
25-Jul-2007
URT-STD
UMSH-7867MD-4CS
OF
���� ������ � � �� ����� �� ����� � ���� ��� ������ � ����
CUSTOMER APPROVED SIGNATURE
Page: 1
Allen Wang Angus Chiu Sharon Tsai Jul-25-2007APPROVED CHECKED CHECKED PREPARED
U.R.T.
U.R.T.
Document Model No. Revision
Revision Version No. by
0
1
2
3
4
1. Include URT standard touch panel.Bryan HuangGary Yang08-Aug-2006
Description
�������� ����
UMSH-7867MD-CS(UCSH-K041EN-FT)
Version No. 05.7” CSTN use the LED B/L.
Bryan HuangGary Yang20-JUN-2006
UMSH-7867MD-1CS(UCSH-K041EN-FT)
Version No. 0
Page: 2
UMSH-7867MD-4CS(UCSH-K064ENY-FT)
Version No. 0
1. Merge the PCB into one pcs.2. Modify the B/L housing conform to the PCB.3. Modify the LCD outline.4. Modify the driver IC version .5. Modify the module number from UMSH-7867MD-CS to UMSH-7867MD-4CS.
Flyon LiaoGary Yang25-Jul-2007
UMSH-7867MD-2CS(UCSH-K041EN-1FT)
Version No. 0
1. Increased the display result.2. Modify the module number from UMSH-7867MD-CS to UMSH-7867MD-2CS.
Mandy HsuGary Yang7-Sep-2006
UMSH-7867MD-3CS(UCSH-K041EN-FT)
Version No. 0
1. Improved the display result of the backlight.2. Modify the module number from UMSH-7867MD-CS to UMSH-7867MD-3CS.
Flyon LiaoGary Yang
U.R.T.
CONTENTS:
No. Item PageBASIC SPECIFICATION
1.1 Mechanical Specification
1.3 Outline Dimension1.4 Block Diagram1.5 Interface Pin
ELECTRICAL CHARACTERISTICS
2.3 Back-light Characteristics ( LED )2.4 AC Characteristics 11~132.5 Interface Timing Chart2.6 Power Supply Sequence
OPTICAL CHARACTERISTICS
3.2 Definition of Optical Characteristics 17~18
RELIABILITY
PRODUCT HANDING AND APPLICATION
DATECODE
PACKING & LOTNO 22~23
INSPECTION STANDARD 24~27
Page: 3U.R.T.
1. BASIC SPECIFICATION
1.1 Mechanical specifications
Items
Dot Matrix
Module Size (W x H x T)
Viewing Area (W x H)
Active Area (W x H)
Dot Size (W x H)
Dot Pitch (W x H)
Driving method
Driving IC Package
1.2 Display specification
LCD Type
LCD Mode
Polarizer Mode
Polarizer UV-Cutting
Polarizer Surface
Background Color
Backlight Type
Backlight Color
Viewing Direction
Duty
Bias
Display Descriptions Note
1/240
1/16
TAB
mm.
mm.
mm.
mm.
Nominal Dimension Unit
dots
mm.
320*RGB*240
154.6 x 114.8 x 8.5
118.18 x 89.38
115.18 x 86.38
0.105 x 0.345
0.12 x 0.36
5.7" Color STN
Negative
Transmissive
With
Normal
Black
LED
White
4
6 O'clock Direction
Page:U.R.T.
1.4 Block diagram:
Recommended Circuit for Contrast Adjustment
Page: 6U.R.T.
LCD320xRGBx240 Dots
Segment Driver ICNT7706TAB0008A *4
Co
mm
on
Driver IC
NT
7705TA
B0009A
*2
��� ���������
Power &Bias circuit
C1
C240
S1 S320
MCircuit
LED1
LED2
D7~D0
VLCD
VSS
VDD
/DISP
CL2
CL1
FRM
8
2-5 Interface Timing Chart
Page: 14U.R.T.
X240 X1 X2 X3 X240 X1 X2 X3
G318 R1
B318
R319
G319
B319
R320
G320
B320
R4
R7
R3
R2
R6
R5
G1
G2
G3
G4
G5
G6
G7
G8
B1
B2
B3
B4
B5
B8
B6
B7
R8
R319
G318
G319
G320
B320
B318
B319
B320
R1
G1
B1
R2
G2
B2
R3
G3
FLM
CL1
LATCHDATA
CL1
CL2
D7
D6
D5
D4
D3
D2
D1
D0
FLM
3. OPTICAL CHARACTERISTICS
3.1 Characteristics
Driving condition
Electrical and Optical Characteristics
No. Item symbol / temp. Min. Typ. Max. Unit Note
Response Time Tr - 260 520
Tf - 100 200
Viewing Front-Rear 1 -10 - 30
Angle Left-Right 2 -30 - 30
Contrast Ratio Cr - 35 -
Red x-code Rx 0.56
Red y-code Ry
Green x-code Gx
Green y-code Gy
Blue x-code Bx
Blue y-code By
White x-code Wx
White y-code Wy
Brightness Y - -
16
Bias1/16
Note1
- -
2
ItemValue
5
ms
Duty1/240
degree 3
% 6Brightness Uniformity
Page:
cd/m2
-
90°
- 4
U.R.T.
3.2 Definition of optical characteristics
Measurement condition :
[Note 1] Definition of LCD Driving Vop and Waveform :
[Note 2] Definition of Response Time
[Note 3] Definition of Viewing Angle : [Note 4] Definition of Contrast Ratio :
Page: �&U.R.T.
[Note 5] Definition of measurement of Color Chromaticity and Brightness
[Note 6] Definition of Brightness Uniformity
[Note 7] Definition of Measurement of Reflectance
Page: 18U.R.T.
480m
m
BM
-7
LCD Module
1 2 3
4 5 6
7 8 9
W / 4
Active Area Width : W
Act
ive
Are
a H
eigh
t : H
H /
4
480m
m
BM
-7
LCD Moduleor referance
15 deg.
White Light Source(Ring)
Brightness Uniformity =
Minimum Brightness of Point 1~9
Maximum Brightness of Point 1~9
4. RELIABILITY :
High temperature operatingLow temperature operatingHigh temperature storageLow temperature storageHigh temperature & humidity storageThermal Shock -20 , 30min.<=> 70 , 30min. storage 10 Cycles
10 => 55 =>10 => 55 => 10 Hz , within 1 minute Amplitude : 1.5mm. 15 minutes for each Direction ( X,Y,Z )
50,000 hoursLife time 25 , 70%RH below ,
* One single product test for only one item.* Judgment after test : keep in room temperature for more than 2 hours.
- Current consumption < 2 times of initial value- Contrast > 1/2 initial value- Function : work normally
Finish product(With polarizer)
Finish product(With polarizer)Finish product
(With polarizer)Finish product
(With polarizer)Finish product
(With polarizer)
Remark
8 Drop test
4
5
Packed, 100CM free fall, 6 sides, 1 corner, 3edges
Vibration test7
ConditionItem No
'
1
2
3
Items
60 , 200 hours
-10 , 200 hours
70 , 200 hours
Page: 19
-20 , 200 hours
6
Finish product(With polarizer)
Finish product(With polarizer)
Finish product(With polarizer)
Finish product(With polarizer)
U.R.T.
5. PRODUCT HANDING AND APPLICATION
� (����)���* +�� ��*���*� ���
The LCD module contains a C-MOS LSI. People who operate the LCM should wear ESD protection eguipement to prevent ESD hurt on products.
Do not input any signal before power is turned on.
Do not take LCM from its packaging bag until it is assembled.
Peel off the LCM protective film slowly since static electricity may be generated.
Pay attention to the humidity of the work shop, 50~60%RH is satisfactory.
Use a non-leak iron for soldering LCM.
Do not touch the display surface or connection terminals area with bare hands.Smudges on the display surface reduce the insulation between terminals.
Cautions for soldering to LCM:
Condition for soldering I/O terminals: Temperature at iron tip :280 ±10 . Soldering time : 3~4sec./ terminals.
Type of solder : Eutectic solder(rosin flux filled).
� PRECAUTION IN USE OF LCD
Do not contact or scratch the front surface and the contact pads of a LCD panel with hard materials such as metal or glass or with one’ s nail.
To clean the surface , wipe it gently with soft cloth dampened by alcohol.
Do not attempt to wiped off the contact pads.
Keep LCD panels away from direct sunlight , also avoid them in high-temperature & high humidity environment for a long period.
Do not drive LCD panels by DC voltage.
Do not expose LCD panels to organic solvent.
Liquid in LCD is hazardous substance. In case a contact with liquid crystal material is occured, be sure to immediately wash such material away by soap and water.
The polarizer is easily damaged and should be handle with special care. Don’ t press or rub it with hard objects.
� (����)���* +�� ,����*� ���
To avoid degradation of the device , do not store the module under the conditions of direct sunlight , high temperature or high humidity . Keep the module in bags designed to prevent
static electricity charging under low temperature / normal humidity conditions(avoid high
temperature / high humidity and low temperature below 0 )
� ),�*� �* ������� ���� - ,�+��. �� ��/����), �((�������* �� ,.,���
For the application in medical care, safety and hazardous prodcuts or systems, an authorization from URT is required. URT will not responsible for any damage or loss
which caused by the products without any authorization given by URT.
This product is not allowed to be designed and used for military application and/or purpose.
The delivery of this product to the countries and/or regions where the embargoes
are imposed by U.N. is prohibited.
Page: 20U.R.T.
6. DATE CODE OF PRODUCTS
Date code will be shown on each product :
Y MM DD - XXX
Year Month Day - Production lots
21
Example: 2 1 2 2 3 - 0 0 3 ==>Year 2002, Dec.,23rd , Batch no.03
Page:U.R.T.
7. PACKING
Packing tray must be stacked with alternated direction to each others.To tacks packing trays in same direction will cause product damaged.
22Page:U.R.T.
8. INSPECTION STANDARD
8.1. QUALITY :THE QUALITY OF GOODS SUPPLIED TO PURCHASER SHALL COME UP TO THE FOLLOWING STANDARD.
8.1.1. THE METHOD OF PRESERVING GOODSAFTER DELIVERY OF GOODS FROM U.R.T. TO PURCHASER. PURCHASER SHALL CONTROL THE LCM
AT -10 40 ,AND IT MIGHT BE DESIRABLE TO KEEP AT THE NORMAL ROOM TEMPERATURE
AND HUMIDITY UNTIL INCOMING INSPECTION OR THROWING INTO PROCESS LINE.
8.1.2. INCOMING INSPECTION(A) THE METHOD OF INSPECTION
IF PURCHASER MAKE AN INCOMING INSPECTION , A SAMPLING PLAN SHALL BE
APPLIED ON THE CONDITION THAT QUALITY OF ONE DELIVERY SHALL BE
REGARDED AS ONE LOT.
(B) THE STANDARD OF QUALITY
ISO-2859-1 ( or MIL-STD-105D ) , LEVEL SINGLE PLAN.
CLASS AQL(%)CRITICAL 0.4 %MAJOR 0.65 %MINOR .5 %TOTAL .5 %
EVERY ITEM SHALL BE INSPECTED ACCORDING TO THE CLASS.
(C) MEASURE
IF AS THE RESULT OF ABOVE RECEIVING INSPECTION , A LOT OUT IS DISCOVERED.
PURCHASER SHALL BE INFORM SELLER OF IT WITHIN SEVEN DAYS. BUT FIRST SHIPMENT
WITHIN FOURTEEN DAYS.
8.1.3. WARRANTY POLICYU.R.T. WILL PROVIDE ONE-YEAR WARRANTY FOR THE PRODUCTS ONLY IF UNDER SPECIFICATION
OPERATING CONDITIONS. U.R.T. WILL REPLACE NEW PRODUCTS FOR THESE DEFECT PRODUCTS
WHICH UNDER WARRANTY PERIOD AND BELONG TO THE RESPONSIBILITY OF U.R.T.
8.2. CHECKING CONDITION8.2.1. CHECKING DIRECTION SHALL BE IN THE 45 DEGREE AREA TO FACE THE SAMPLE.
8.2.2. CHECKER SHALL SEE OVER 30 cm. WITH BARE EYES FAR FROM SAMPLE AND USING 2 PCS.
OF 20W FLUORESCENT LAMP.
24Page:U.R.T.
8.3. INSPECTION PLAN :
CLASS ITEM JUDGEMENT CLASS
1. OUTSIDE AND INSIDE PACKAGE "MODEL NO." , "LOT NO." AND "QUANTITY"
PACKING & SHOULD INDICATE ON THE PACKAGE.
INDICATE 2. MODEL MIXED AND QUANTITY OTHER MODEL MIXED................REJECTED
QUANTITY SHORT OR OVER......REJECTED
3. PRODUCT INDICATION "MODEL NO." SHOULD INDICATE ON
THE PRODUCT
4. DIMENSION, ACCORDING TO SPECIFICATION
ASSEMBLY LCD GLASS SCRATCH DRAWING.
AND SCRIBE DEFECT.
5. VIEWING AREA POLARIZER EDGE OR LCD'S SEALING LINE
IS VISABLE IN THE VIEWING AREA
……..REJECTED
6. BLEMISH BLACK SPOT ACCORDING TO STANDARD OF VISUAL
WHITE SPOT IN THE LCD INSPECTION
AND LCD GLASS CRACKS
7. BLEMISH BLACK SPOT ACCORDING TO STANDARD OF VISUAL
APPEARANCE WHITE SPOT AND SCRTCH
ON THE POLARIZER
8. BUBBLE IN POLARIZER ACCORDING TO STANDARD OF VISUAL
INSPECTION
9. LCD'S RAINBOW COLOR STRONG DEVIATION COLOR ( OR NEWTON
RING) OF LCD......REJECTED.
OR ACCORDING TO LIMITED SAMPLE
( IF NEEDED, AND INSIDE VIEWING AREA )
10. ELECTRICAL AND OPTICAL ACCORDING TO SPECIFICATION OR
CHARACTERISTICS DRAWING . ( INSIDE VIEWING AREA )
( CONTRAST VOP
CHROMATICITY … ETC )
ELECTRICAL 11.MISSING LINE MISSING DOT LINE CHARACTER
....REJECTED
12.SHORT CIRCUIT NON DISPLAY WRONG PATTERN
WRONG PATTERN DISPLAY DISPLAY CURRENT CONSUMPTION
OUT OF SPECIFICATION...... REJECTED
13. PIN HOLE PATTERN DEFORMITY ACCORDING TO STANDARD OF VISUAL
INSPECTION
25Page:
Minor
Critical
Major
Major
Minor
Minor
Minor
Minor
Minor
Minor
Critical
Critical
Critical
U.R.T.
8.4. STANDARD OF VISUAL INSPECTIONNO. CLASS ITEM JUDGEMENT
(A) ROUND TYPE: unit : mm.
DIAMETER (mm.) ACCEPTABLE Q'TY
BLEMISH BLACK SPOT 0.1
8.4.1 WHITE SPOT IN THE LCD. 0.1 < 0.2
0.2 < 0.25
0.25 <
BLEMISH BLACK SPOT NOTE: =(LENGTH+WIDTH)/2
WHITE SPOT AND SCRATCH (B) LINER TYPE: unit : mm.
ON THE POLARIZER LENGTH ACCEPTABLE Q'TY
------ W 0.03
L 5.0 0.03 < W 0.05
L 5.0 0.05 < W 0.07
------ 0.07 < W FOLLOW ROUND TYPE
unit : mm.
DIAMETER
8.4.2 BUBBLE IN POLARIZER 0.15
0.15 < 0.5
0.5 <
unit : mm.
8.4.3 PIN HOLE
PATTERN DEFORMITY 0.1
0.1 < 0.25
0.25 <
=(a+b)/2
26Page:
MINOR
MINOR
MINOR
3
1
DISREGARD
0
WIDTH
ACCEPTABLE Q'TY
DISREGARD
DISREGARD
2
1
0
2
0
DIAMETER ACC. Q'TY
DISREGARD
3
U.R.T
a
b
a
ab
b
NO. CLASS ITEM JUDGEMENT
8.4.4 CHIPPING Y > S REJ.
8.4.5 CHIPPING X or Y > SREJ.
8.4.6 GLASS CRACK Y > (1/2) TREJ.
1. a> L/3 , A>1.5mm.
8.4.7 SCRIBE DEFECT REJ.
2. B : ACCORDING
TO DIMENSION
8.4.8 CHIPPING
( ON THE TERMINAL AREA ) REJ.
8.4.9 CHIPPING Y > (1/3) T
( ON THE TERMINAL SURFACE ) REJ.
8.4.10 CHIPPING Y > T REJ.
MINOR
MINOR
MINOR
MINOR
MINOR
MAJOR
MAJOR
27Page:U.R.T.