213.250.6069 DMX SYSTEM INSTALLATION GUIDESystem+INSTALLATION+GUIDE.pdf · 2 of 21 213.250.6069...

1 of 21

213.250.6069

[email protected]

www.opticarts.com

Optic Arts reserves the right to modify this specification without prior notice. Last Modified: January 29, 2018

© Optic Arts 2018; 1130 Monterey Pass Rd, Monterey Park, CA 91754

DMX SYSTEM INSTALLATION GUIDENOTES

Please read entire guide prior to starting installation.

1. All installations shall be executed in accordance with local building codes.

2. The installing contractor assumes all liability for the safety and code compliance of the

installation.

3. Optic Arts is not liable for any damages caused by improper wiring, circuit overloading,

power surges, system design or layout, negligence, or other conditions.

DMX SYSTEM STANDALONE MODE

UL LISTED ENCLOSURE (BY OTHERS)

DMX MODULE

DMX MODULE

®®

24V DC+

24V DC+

24V DC-

24V DC-

LED+CH1 -CH2 -CH3 -CH4 -


GG

100E

-24-

UN

V

GG

100E

-24-

UN

VLED+

LED+

R

R

G

G

B

B

W/A

W/A

OUT TO NEXT MODULE

LEDSync thru +LEDSync thru -LEDSync shield

DMX in +

LEDSync thru +LEDSync thru -

DMX in -DMX in shield

LEDSync shield

DMX Cabling such as Belden 9841 (or similar):

• Blue > DMX+• White > DMX–• Shield > Common

2 of 21

213.250.6069

[email protected]

www.opticarts.com


DMX SYSTEM INSTALLATION GUIDE


DMX System With DMX Controller

Diagram #1 Diagram #2

DMX System with DMX Controller

and Power Supply



DMX MODULE DMX MODULE

DMX MODULE DMX MODULE

® ®

® ®

24V DC+ 24V DC+

24V DC+

24V DC+ 24V DC+

24V DC- 24V DC-

24V DC-

24V DC- 24V DC-





LED+ LED+

LED+ LED+

R R

R R

G G

G G

B B

B B

W/A W/A

W/A W/A

CTRLDMX.4CH.3S.W(OR BY OTHERS)


OUT TO NEXT MODULE OUT TO NEXT MODULE

DMX Cabling such as Belden 9841 (or similar)*: DMX Cabling such as Belden 9841 (or similar)*:Blue > DMX+ Blue > DMX+White > DMX– White > DMX–Shield > Common Shield > Common

DMX in +

LEDSync thru +

LEDSync thru -

DMX in -

DMX in shield

LEDSync shield

DMX in +

LEDSync thru +

LEDSync thru -

DMX in -

DMX in shield

LEDSync shield

DMX in +

LEDSync thru +

LEDSync thru -

DMX in -

DMX in shield

LEDSync shield

DMX in +

LEDSync thru +

LEDSync thru -

DMX in -

DMX in shield

LEDSync shield



GND GNDD+ D+D- D-V+ V+V- V-

GG

100E

-24-

UN

V

GG

100E

-24-

UN

V

GG

100E

-24-

UN

V

GG

100E

-24-

UN

V

LV10-24N-120-A(OR BY OTHERS)

(Mounted in junction box)120VAC

3 of 21

213.250.6069

[email protected]

www.opticarts.com




1.

1.1 Identify mounting location for driver & eldoLED® LinearDrive100D(s). eldoLED® LinearDrive100D(s) must be mounted in a UL listed Junction Box (by others).

1.2 Remove faceplate cover.

1.3 Mount eldoLED® LinearDrive100D(s) in a UL listed Junction Box (by others).

1.4 Remove strain relief pieces.

Strain Relief Strain Relief

WIRING INSTALLATION

4 of 21

213.250.6069

[email protected]

www.opticarts.com




2.

2.1 Wire 24VDC into eldoLED® LinearDrive100D(s) using the GG100E-24-UNV(s) through UL Listed conduit(s).

ELECTRONICDRIVER

UL Listed Enclosure (By Others)(Repeat step for additional drivers)

(Repeat step for additional modules)

24V DC+

24V DC-

Page must be printed in color.

5 of 21

213.250.6069

[email protected]

www.opticarts.com



DMX SYSTEM INSTALLATION GUIDEWIRING INSTALLATION

3.

3.1 Connect lead wires from light fixture or tape, as applicable to the product

being installed.

LED+

LED+

LED+

LED+LED-

R

R

C*

G

G

W

• FLEX RGBA/W

• FLEX VW

• FLEX Single Color

• FLEX RGB

FLEX WIRING:

B

B

W/A

24V DC-

24V DC+

GG100E-24-UNV

* Wire is either white or red, depending on specific product.


6 of 21

213.250.6069

[email protected]

www.opticarts.com




• FLEX RGBA/W

• FLEX VW

• FLEX Single Color

• FLEX RGB

VISUAL TEST:

On Screen: At Fixture:

No Light

No Light

No Light

No Light

No Light

No Light

4.

4.1 Run visual test by tapping the three control buttons simultaneously.

4.2 If LEDs on fixture flash in sequence shown on display, the eldoLED® LinearDrive100D is successfully installed.

M — ++ +(See Visual Test)(Press at the same time)

TEST Display Off

*Color specified will flash

2x R

G

B

W

RGBW

2x

2x

2x *

*

R

R

R

G

G

G

B

B

B

W

W

W

RGBW

RGBW

RGBW

If any control channels are not functioning, turn to next page to troubleshoot the malfunctioning FLEX product.


7 of 21

213.250.6069

[email protected]

www.opticarts.com




4. Cntd. TROUBLESHOOTING MALFUNCTIONING FLEX PRODUCT

A. If none of the FLEX LEDs are turning on, tap M button to see if display on eldoLED® Linear100D will turn on.

Follow step by step until issue is resolved.

• If display does not turn on, turn to next page to review TROUBLESHOOTING MALFUNCTIONING eldoLED® Linear100D.

• If display does turn on, move on to next step.

M M M M+ LED EXT INP DIM CURV

LED Groups(Click + or - to change)

B) LED GROUPS

Single Color

RGBRGBW

Variable White

External Input Dimming Curve

Display Off

1-1L2-2L3-3L4-4L2-4L1-4LRGB

RGBWRGBARRGBRGGBCCWWCWWW

OFFPOTM10VSWIT

LOGLIN

M M MM M

C) SINGLE COLOR C Cntd.) VARIABLE WHITEChannel 1 (Cool)Channel 1 Channel 2 (Warm)

Display Off Display Off

Hold to Change Intensity Hold to Change Intensity Hold to Change Intensity

OR OR OR

M M M M

C Cntd.) RGBChannel 1 (Red) Channel 2 (Green) Channel 3 (Blue)

Display Off


OR OR OR

M M M M M

C Cntd.) RGBA/WChannel 1 (Red) Channel 2 (Green) Channel 3 (Blue) Channel 4 (Amber/White)

Display Off

Hold to Change Intensity Hold to Change Intensity Hold to Change Intensity Hold to Change Intensity

OR OR OR OR

B. Program eldoLED® Linear100D to relevant Color Group to match LED setup. Hold to switch to color.

C. Raise the intensity of the first color to ensure that a FLEX color correlates with the channel. Lower the intensity to lowest setting, and repeat with next channel until each color has been verified.

• If FLEX color does not match its corresponding channel, rewire and retest each channel. Once FLEX color matches corresponding channel, reset DMX module and move on to Step 5 (pg. 9)

• If any channel is not functioning, check wiring, and retest each channel. If channel error persists, contact Optic Arts at (213) 250-6069.

M Display Off

Reset to Factory Defaults

M — ++ + RESETPRESS MENU

Reset(Press & hold for 5 sec)

OPTIC ARTS PRO TIP:If eldoLED® Linear100D continues to malfunction, refer to Reset To Factory Default.

M

8 of 21

213.250.6069

[email protected]

www.opticarts.com




4. Cntd.TROUBLESHOOTING MALFUNCTIONING eldoLED® Linear100D

A. Hold down all three buttons for 5 seconds to reset eldoLED® Linear100D. If eldoLED® Linear100D display does not turn on,

move on to next step.

B. Wire a different eldoLED® Linear100D to same driver. If eldoLED® Linear100D display does not turn on, repeat Step A with

multiple eldoLED® Linear100D modules. If multiple eldoLED® Linear100D displays still do not turn on, move on to next step.

C. Wire eldoLED® Linear100D to another driver. Driver must be off first. Do not wire hot. If eldoLED® Linear100D display does not

turn on, repeat Step A with multiple eldoLED® Linear100D modules on the most current driver. If multiple eldoLED® Linear100D

displays do not turn on, turn to next page to review TROUBLESHOOTING MALFUNCTIONING ELECTRONIC DRIVER.


9 of 21

213.250.6069

[email protected]

www.opticarts.com




4. Cntd.TROUBLESHOOTING MALFUNCTIONING ELECTRONIC DRIVER

A. Wire one channel of FLEX product directly into ELECTRONIC DRIVER. If FLEX product does not turn on, move on to next step.

B. Wire the same channel of FLEX product to a different ELECTRONIC DRIVER. If FLEX product still does not turn on, repeat Step A & B

with a different FLEX channel or FLEX product. If FLEX product still does not turn on, check input power to driver(s) (120/277 VAC).

• If issue is found with input power, resolve issue and return to Step 2 (pg. 3).

• If input power is not the issue, contact Optic Arts at (213) 250-6069 to replace ELECTRONIC DRIVER(s).

DRIVER MUST BE OFF FIRST - DO NOT WIRE HOT


10 of 21

213.250.6069

[email protected]

www.opticarts.com




5 STANDALONE.M M M M+ LED EXT INP DIM CURV


Single Color

RGBRGBW

Variable White


Display Off

1-1L2-2L3-3L4-4L2-4L1-4LRGB

RGBWRGBARRGBRGGBCCWWCWWW

OFFPOTM10VSWIT

LOGLIN

M M

C) SINGLE COLOR

Channel 1

Display Off

Hold to Change Intensity

OR M M M

C Cntd.) VARIABLE WHITE

Channel 1 (Cool) Channel 2 (Warm)

Display Off

Hold to Change Intensity Hold to Change Intensity

OR OR

M M M M

C Cntd.) RGB

Channel 1 (Red) Channel 2 (Green) Channel 3 (Blue)

Display Off


OR OR OR

M M M M M

C Cntd.) RGBA/W

Channel 1 (Red) Channel 2 (Green) Channel 3 (Blue) Channel 4 (Amber/White)

Display Off

Hold to Change Intensity Hold to Change Intensity Hold to Change Intensity Hold to Change Intensity

OR OR OR OR

M Display Off

LED Groups




5.1 Program eldoLED® Linear100D to relevant color group to match LED strip (See List).

5.2 Adjust intensity of each channel until the desired color is

reached. Use diagrams on the right to program correlating

color scheme.

*If eldoLED® Linear100D does not function properly, reset to factory defaults.


11 of 21

213.250.6069

[email protected]

www.opticarts.com




5 DMX CONTROLLER.

5.1 Wire eldoLED® Linear100D to DMX Controller (Either Optic Arts® provided or by others). If multiple eldoLED® Linear100Ds are

used, connect in parallel to other eldoLED® Linear100Ds.

5.2 Set mode to DMX.


M M

M

SET MODE

Set Mode (Click + or - to change)(5 sec)

Display Off

Display Off

COLRSHOWDMX


DMX Controller Wiring

Set Mode to DMX



All DMX cabling shall conform to ANSI E1.27-2-2009 (R2014), recommended practice for permanently installed control cables for use with ANSI E1.11 (DMX512-A) and USITT DMX512/1990 products. The maximum total length of a daisy-chain DMX control run is 300 meters (1,000 feet) using the lowest grade cabling

conforming to ANSI E1.27-2-2009 (R2014). Improved wire gauge and shielding can extend this limitation. Some additional devices such as repeaters or splitters may also extend this limitation. Consult manufacturer to validate any limitation extensions. Every DMX control run must be terminated after the last DMX

control module in a daisy-chain sequence with a DMX terminator..

OPTIC ARTS® DMX CONTROLLER OR

BY OTHERS

OPTIC ARTS PRO TIP: Max of 10 modules on one DMX line. Consult DMX Controller datasheet for maximum device limitation specific controller.

DMX Cabling such as Belden 9841 (or similar)*:Blue > DMX+White > DMX–Shield > Common


OUT TO NEXT MODULE

DMX in +



LEDSync shield

DMX in +



LEDSync shield

24V DC-

24V DC+

To F

LEX

To F

LEX

12 of 21

213.250.6069

[email protected]

www.opticarts.com




5.3 Program eldoLED® Linear100D to relevant color group to match LED strip (See List).


M M M M+ LED EXT INP DIM CURV


Single Color

RGBRGBW

Variable White


Display Off

1-1L2-2L3-3L4-4L2-4L1-4LRGBRGBWRGBARRGBRGGBCCWWCWWW

OFFPOTM10VSWIT

LOGLIN

LED Groups

5 DMX CONTROLLER.

13 of 21

213.250.6069

[email protected]

www.opticarts.com




5.4 Set DMX Addresses according to the desired zones of control.


M M M MDMX ADDR NETW RES INTERPOL

DMX Address(Click + or - to change)

FLEX RGB ConfigurationDMX Addresses increase by increments of 3 DMX Addresses increase by increments of 4 DMX Addresses increase by increments of 2

FLEX VW ConfigurationFLEX RGBA/W Configuration

External Input Interpol

Display Off

*1...512 8 BT16 BT

OFFVIDCOLRWHITGLOW

Setting DMX Address

M Display Off




1

4

1

3

DM

X CO

NTR

OLL

ER

BY O

THER

S

1

5

OPT

IC A

RTS®

DM

X

CON

TRO

LLER

OR

BY

OTH

ERS

7 59

5 DMX CONTROLLER.


(Repeat step for additional modules) (Repeat step for additional modules) (Repeat step for additional modules)

DM

X CO

NTR

OLL

ER

BY O

THER

S

24V DC-

To F

LEX

To F

LEX

To F

LEX

To F

LEX

To F

LEX

To F

LEX

To F

LEX

To F

LEX

To F

LEX

24V DC- 24V DC- 24V DC-

24V DC- 24V DC-

24V DC- 24V DC- 24V DC-

24V DC+

24V DC+ 24V DC+ 24V DC+

24V DC+ 24V DC+

24V DC+ 24V DC+ 24V DC+

OUT TO NEXT MODULE OUT TO NEXT MODULE OUT TO NEXT MODULE

14 of 21

213.250.6069

[email protected]

www.opticarts.com




5.5 Remove faceplate from controller by carefully inserting a flathead screwdriver into

slot A and gently pulling up.

A

This step only is applicable if using an Optic Arts® DMX controller (CTRLDMX.4CH.3S.W).5 DMX CONTROLLER.

15 of 21

213.250.6069

[email protected]

www.opticarts.com




This step only is applicable if using an Optic Arts® DMX controller (CTRLDMX.4CH.3S.W).

5.6 Wire DMX Controller to eldoLED® Linear100D.

24V DC+

24V DC+

24V DC-

24V DC-

GG100E-24-UNV

GG100E-24-UNV

CTRLDMX.4CH.3S.W

CTRLDMX.4CH.3S.W

DMX Controller Power Supply

(LV10-24N-120-A)

CTRLDMX.4CH.3S.W

DMX Cabling such as Belden 9841 (or similar)*:

• Blue > DMX+• White > DMX–• Shield > Common

24V

DC-

24V

DC+

DM

X in

+

DM

X in

-

DM

X in

shi

eld

GG100E-24-UNVor

LV10-24N-120-A

LINEARdrive 100D

5 DMX CONTROLLER.

CTRLDMX.4CH.3S.W

CTRLDMX.4CH.3S.W

GND

GND

D+

D+

D-

D-

V+

V+

V-

V-

OUT TO NEXT MODULE

OUT TO NEXT MODULE

DMX in +



LEDSync shield

DMX in +



LEDSync shield

24V DC-

24V DC+

To F

LEX

To F

LEX

16 of 21

213.250.6069

[email protected]

www.opticarts.com




5.7 Make power and DMX connections on the controller body

terminal blocks (See Figure 1). If DMX Controller Power Supply is

used, make connection and place power supply in junction box

before proceeding to next step.

5.8 Mount controller body on Junction Box with screws.

5.9 Align faceplate connector with pins on controller body and snap

faceplate into place.

5.10 Fit controller onto Junction Box.

Note: Power to come from GG100E-24-UNV Driver used to power

fixtures. Controller consumes 5 watts.

Figure 1

Figure 2

DMX Controller Power Suppy

Note: Wire color coding depends on wire type used.

Note: Wire color coding depends on wire type used.

5 DMX CONTROLLER.DMX Controller wired to GG100E-24-UNV Driver DMX Controller wired to DMX Controller Power Supply

Note: Refer to Diagram #2 on Page 2 for wiring instructions.

Note: Refer to Diagram #2 on Page 2 for wiring instructions.

CTRLDMX.4CH.3S.W

CTRLDMX.4CH.3S.W

GND

GND

D+

D+

D-

D-

V+

V+

V-

V-

This step only is applicable if using an Optic Arts® DMX controller (CTRLDMX.4CH.3S.W).

17 of 21

213.250.6069

[email protected]

www.opticarts.com




5.11 Test each function of DMX Controller to ensure successful installation.

Red Channel• Tap to turn on/off

• Hold to adjust light intensity

WALL MOUNTED DMX CONTROLLERBUTTON FUNCTIONS

Green Channel• Tap to turn on/off• Hold to adjust light intensity

Blue Channel• Tap to turn on/off

• Hold to adjust light intensity

Warm White, Natural White, Cool White• Tap to switch between warm, natural & cool white mixed

with RGB

Hold to adjust overall light intensity

Select color from RGB color wheel

White Channel• Tap to turn on/off• Hold to adjust light intensity

Master on/off

• Play/Pause programmed effects• Hold to adjust effect speed

• Hold to save color/effects preset• Tap to recall preset

5 DMX CONTROLLER. This step only is applicable if using an Optic Arts® DMX controller (CTRLDMX.4CH.3S.W).

18 of 21

213.250.6069

[email protected]

www.opticarts.com




TROUBLESHOOTING DMX CONTROLLER

A. If controller is unresponsive, push to turn off controller (red LED will light on Controller), then push to turn on (blue

LED will light on controller) & retest controller functionality. If light fixture does not turn on, move on to next step.

B. Turn on controller and hold down to test and see if light fixture ramps up or down. Repeat, hold down button 2-3 times. If

FLEX LED does not turn on, move on to next step.

C. Turn on controller and tap each of the following color buttons _________ or _________ or _________ or _________, If FLEX LED does not

turn on, then hold down color wheel buttons to test if LED brightens/dims. Repeat 2-3 times for each. If FLEX LED does not turn

on, move on to next step.

D. Turn on controller and scroll through center color wheel. If FLEX LED does not turn on, move on to next step.

E. Set groups on LinearDrive100D (See Step 4.2, page 4) to COLOR, then SHOW, then back to DMX. Repeat steps from Troubleshooting

Step A. If FLEX LED does not turn on, move on to next step.

F. Check wiring (See Step 4, page 4), then check every setting following to match corresponding FLEX LED. Repeat steps from

Troubleshoot Step A. If FLEX LED does not turn on, move on to next step.

G. Reset eldoLED® Linear100D to factory settings and start from Step 4 (see page 4). Repeat Troubleshooting DMX Controller.


5 DMX CONTROLLER.Page must be printed in color.

19 of 21

213.250.6069

[email protected]

www.opticarts.com




6.

6.1 Reinstall strain relief pieces.

6.2 Reinstall faceplate cover.

6.3 Cover UL Listed Enclosure (by others).

eldoLED® Linear100D

To FLEXTo GG100E-24-UNV

20 of 21

213.250.6069

[email protected]

www.opticarts.com




Problem Solved!

Tap M button on eldoLED® Linear100D. Does the eldoLED®

Linear100D display turn on?

Do all eldoLED® Linear 100D(s) fail to turn on?

Do all FLEX colors match the corresponding control channel?

Check wiring and retest each channel. Does error persist?

Contact Optic Arts at 213.250.6069

Program eldoLED® Linear100D to relevant Color Group

to ensure FLEX color coordinates with control

channel to match LED setup. (Reference TROUBLESHOOTING

MALFUNCTIONING FLEX PRODUCT STEP B & C for further

instruction). Do all FLEX channels turn on?

Wire each channel of FLEX product directly into ELECTRONIC DRIVER.

Do all FLEX channels turn on?

Wire another FLEX lunimnaire to the same driver. If FLEX does not

turn on, re-test with all other FLEX. Are all FLEX not turning on?

Wire same product to another driver. If product does not work, retest with all other drivers. Are

all drivers not turning on product?

Check input power line. Are all drivers working?

No

No

No

Yes

Yes

Wire another eldoLED® Linear 100D to same driver. If eldoLED® Linear 100D does not turn on, re-

test with all other eldoLED® Linear 100D. Are all eldoLED® Linear

100D(s) functioning?

No

Yes

No

No

Yes

No

Yes

No

Yes

YesNo

Yes

Yes

Yes

START HERE

No

DRIVER/eldoLED® LINEAR100D/FLEX LED TROUBLESHOOTING

21 of 21

213.250.6069

[email protected]

www.opticarts.com




Problem Solved!

Is the DMX controller responsive?

Tap power button to switch DMX controller on. (Red LED on DMX

controller means on) (Blue LED on DMX controller means off) Does the LED on the DMX controller

light up?

Turn on DMX controller & hold down (sun icon) to test if light

fixture ramps up & down. Repeat hold down 2-3 times. Do any of

the luminaires ramp up?

Check wiring connection of DMX controller. Does the LED on the DMX controller light up after

fixing connection?

Check wiring of every channel that is non-responsive. Are all channels on FLEX responsive to the functions on the DMX

controller?

(See pg. 18) Step D > Do any of the luminaires turn on?

(See pg. 18) Step E > Do any of the luminaires turn on?

(See pg. 18) Step F > Do any of the luminaires turn on?

(See pg. 18) Step G > Do any of the luminaires turn on?

Are all channels on FLEX responsive to the functions on

the DMX controller?

Are all DMX controller features functioning properly?

Are any luminaires responsive to the DMX controller?

Test functions on DMX controller. Are all DMX controller features

functioning properly?

Do any of the luminaires turn on?

Contact Optic Arts at 213.250.6069

START HEREDMX CONTROLLER TROUBLESHOOTING

YesYes

Yes

Yes

Yes

Yes

YesNo

No

No

No

No

No

No

No

No

No

No

No

No

Yes

No

Yes

Yes

Yes

Yes

Yes

Yes

213.250.6069 DMX SYSTEM INSTALLATION GUIDESystem+INSTALLATION+GUIDE.pdf · 2 of 21 213.250.6069...

Documents

Transcript of 213.250.6069 DMX SYSTEM INSTALLATION GUIDESystem+INSTALLATION+GUIDE.pdf · 2 of 21 213.250.6069...