2.0mm SMART CLEANER Fiber Optic Cleaner Smart Cleaner - SCK SS … · Key Features For Cleaning...
4
1 2.0mm SMART CLEANER Fiber Optic Cleaner www.senko.com Key Features For Cleaning SMPTE 304M Connectors 2.0mm SMART CLEANER Fiber Optic Cleaner Best Practices 120mm Short housing for access connectors in confined spaces Rotating cleaning tip uses a sweep & lift motion for effectively wiping away residues and dust particles No need for sleeve removal tools since cleaning tip works for cleaning both Jack and Plug ends Dissipative barrel prevents static charge generation during cleaning process Cleans 400+ endfaces with no need for cleaning solvents P/N SCK-SS-M-200
Transcript of 2.0mm SMART CLEANER Fiber Optic Cleaner Smart Cleaner - SCK SS … · Key Features For Cleaning...
1 2.0mm SMART CLEANER Fiber Optic Cleaner
www.senko.com
Key Features For Cleaning SMPTE 304M Connectors
2.0mm SMART CLEANERFiber Optic Cleaner
Best Practices
120mm
Short housing for access connectors in confined spaces
Rotating cleaning tip uses a sweep & lift motion for effectively wiping away residues and dust particles
No need for sleeve removal tools since cleaning tip works for cleaning both Jack and Plug ends
Dissipative barrel prevents static charge generation during cleaning process
Cleans 400+ endfaces with no need for cleaning solvents
P/N SCK-SS-M-200
2 2.0mm SMART CLEANER Fiber Optic Cleaner
www.senko.com
Best Cleaning Results For Plugs:
Best Cleaning Results For Jacks:
1
1
1
2
2
2
3
4
3
3
Open cover on red end cap
Hold cleaner towards the rear keeping finger tips located on the ridges
Push forward until audible click
1
2
3
4
Place red end cap on back of handle
Hold cleaner towards the rear keeping finger tips located on the ridges
Insert cleaning tip into the jack
Push forward until audible click
Cleaning Plug & Jack
3 2.0mm SMART CLEANER Fiber Optic Cleaner
www.senko.com
Demonstration Of Typical Cleaning Performance
After one engagement
Fine dust particles
After one engagement
Skin oil residue
After one engagement
Moisture residue from duster
Step 1:Apply contaminate
Step 2:Engage cleaner one time
Step 3:Check and record image
1 2 3
Test Setup For Cleaning Demonstration
4 2.0mm SMART CLEANER Fiber Optic Cleaner
www.senko.com
AmericaUSA EAST 1-888-32-SENKOUSA WEST 1-858-623-3300TEXAS [email protected]
AsiaHONG KONG +852-2121-0516SHANGHAI +86-21-5830-4513SHENZHEN [email protected]
EuropeUK +44 (0)1256 700880ITALY +39 011 839 98 28POLAND + 48 71 396 36 [email protected]
Asia PacificAUSTRALIA +61 (0) 3 [email protected]
JapanTOKYO +81 (0) 3 [email protected]
South AmericaBRAZIL [email protected]
www.senko.com
Tips
• Always clean both ends (plug & jack) just before mating for preventing cross contamination.
• If you use canned air dusters in your cleaning regiment, always hold the cans upright to prevent the moisture contamination from the air stream.
• Always clean fiber end faces after blowing connectors with canned air dusters to remove dust particles that may have landed on ferrule surface.
• Remember the SMPTE 304M has electrical contacts so take precautions when using solvents to avoid shorting the circuit.
• Never look directly at the fiber end faces unless you know the signal is off - the wavelength for the optical signal wavelength is 1100nm to 1350nm which is beyond visibility of the human eye.
2.0mm SMART CLEANER Tip
Fiber Optic Ferrule
Low Voltage Electrical Contact (42V AC or 60V DC with 1A current)
Auxiliary Electrical Contact (600V AC with 10A current)
View of 2.0mm SMART CLEANER on Plug
