2086b

NCR RealPOS 82XRT (7606)

Release 1.1

Site Preparation Guide

B005‐0000‐2086

Issue B

The product described in this book is a licensed product of NCR Corporation.

NCR is a registered trademark of NCR Corporation. NCR RealPOS is a trademark of NCR Corporation in the United States and/or other countries. Other product names mentioned in this publication may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.

Where creation of derivative works, modifications or copies of this NCR copyrighted documentation is permitted under the terms and conditions of an agreement you have with NCR, NCRʹs copyright notice must be included.

It is the policy of NCR Corporation (NCR) to improve products as new technology, components, software, and firmware become available. NCR, therefore, reserves the right to change specifications without prior notice.

All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances, photographs are of equipment prototypes. Therefore, before using this document, consult with your NCR representative or NCR office for information that is applicable and current.

To maintain the quality of our publications, we need your comments on the accuracy, clarity, organization, and value of this book.

Address correspondence to:

Manager, Information Solutions GroupNCR CorporationDiscovery Centre, 3 Fulton RoadDundee, DD2 4SWScotland

Internet Address:

http://www.info.ncr.com/eFeedback.cfm

Copyright © 2011By NCR CorporationDuluth, GA U.S.A.All Rights Reserved

http://www.info.ncr.com/eFeedback.cfm

iii

PrefaceThis is a contractual document. It contains important warnings and confers important

legal rights and obligations. You are advised to read it carefully.

It is the responsibility of the customer to ensure that all installation preparations are

complete and in compliance with NCR specifications and requirements and all

applicable national, state, or local codes, regulations, and laws.

Notice: This document is NCR proprietary information and is not to be disclosed or

reproduced without consent.

Safety RequirementsThe NCR RealPOS 82XRT conforms to all applicable legal requirements. To view the

compliance statements see the NCR RealPOS Terminals Safety and Regulatory Statements

(B005‐0000‐1589).

The on/off switch is a logic switch only. The AC line voltage primaries are live at all

times when the power cord is connected. Therefore, disconnect the AC power cord

before opening the unit to install features or service this terminal.

Peripheral UsageThis terminal should only be used with peripheral devices that are certified by the

appropriate safety agency for the country of installation (UL, CSA, TUV, VDE) or those

which are recommended by NCR Corporation.

References• NCR RealPOS 82XRT User Guide (B005‐0000‐2085)

• NCR RealPOS 82XRT Hardware Service Manual (B005‐0000‐2087)

• NCR RealPOS 82XRT Parts Identification Manual (B005‐0000‐2088)

Revision Record

Issue Date Remarks

A Mar 2012 First Issue

B Aug 2012 Release 1.1

iv

About this BookThis book provides site preparation information for NCR RealPOS 82XRT components.

This book does NOT provide Peripheral component and AC wiring site preparation

information. A list of the associated reference documents is in the Related Site

Preparation Data section.

This book contains the information necessary for the preparation of a site conforming

to the NCR specifications. It is very important that the site complies with the

requirements specified in the document because, once the equipment has been

installed, deficiencies in site preparation or the problems caused by these deficiencies

are much more difficult to detect and correct. Further, failure to comply with these

requirements or to take proper steps to protect equipment against risks identified in

this document may cause serious damage to the equipment and to the customerʹs

business.

In addition to the need to comply with the requirements specified, electrical wiring

and mechanical systems must also comply with all relevant codes, laws, and

regulations.

It is important that a customer or his agent who is fully conversant with the special

requirements of electronic equipment prepare the site. The responsibility of ensuring

that the site is prepared in compliance with this document remains with the customer.

For information and guidance purposes only, a list is provided, in general terms, of

those matters for which the customer is responsible. This list does not intend to be

comprehensive, and in no way modifies, alters, or limits the responsibility of the

customer for all aspects of adequate site preparation.

NCR staff is available to answer questions relating to the contents of this document

except where:

• a customer has been notified that a full or partial consultancy service is available

and/or that NCR is willing to undertake a preliminary or final site survey and

• the customer shall have entered into a formal contract with NCR for provision of

the same.

No comment, suggestion, or advice offered or not offered about preparation of the site

nor any inspection of the site whether before or after preparation is to be taken as

approval of the location of the site and equipment or its preparation and NCR is not

liable in respect of any comment, suggestion, or advice given by its staff or in respect to

any failure to give advice.

Finally, only the customer can know the full extent of damage, which may be caused to

his business because of failure of the equipment that is to be installed. For this reason,

it is the customerʹs responsibility to ascertain the extent of any possible damage to his

existing or planned business, and to effect full insurance in respect of it.

v

Table of Contents

Chapter 1: NCR RealPOS 82XRT Terminal Site Preparation

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐1

Model Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐2

Customer Responsibilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐3

Third Party Peripheral Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐4

LAN Communications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐4

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐5

Base Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐5

Integrated Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐5

Integrated Terminal w/Cash Drawer . . . . . . . . . . . . . . . . . . . . . . . 1‐6

7459‐K320 Vertical Mount. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐7

5954 15‐Inch DynaKey. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐8

Standard Remote Table Top Mount (5964‐K030/K031) . . . . . 1‐8

NCR 5964‐K038/K039 Checkstand Mount . . . . . . . . . . . . . . . . 1‐9

NCR 5942 12.1‐Inch LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐10

NCR 5943 12‐Inch LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐10

NCR 5964 12‐Inch Touch LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐11

Standard Remote Table Top Mount (5964‐K031/032) . . . . . 1‐11

NCR 5966 15‐Inch Touch LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐12

NCR 5966 with Table Top Mount . . . . . . . . . . . . . . . . . . . . . 1‐12

NCR 5966 with 5964‐K030/K031 Table Top Mount . . . . . . . 1‐12

NCR 5982 6.5‐Inch Color LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐13

Customer Displays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐14

NCR 5975‐1xxx 2x20 Remote Customer Display . . . . . . . . . . . . 1‐14

NCR 5975‐2xxx Graphical Remote Customer Display . . . . . . . . 1‐15

NCR 5976‐1xxx 2x20 Remote Customer Display . . . . . . . . . . . . 1‐16

Keyboards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐17

NCR 5932‐2xxx 64‐Key POS Keyboard . . . . . . . . . . . . . . . . . 1‐17

NCR 5932‐5xxx USB Big Ticket POS Keyboard . . . . . . . . . . 1‐17

NCR 5932‐6xxx 104‐Key Compact Alphanumeric Keyboard1‐18

NCR 5932‐7xxx PS/2 78‐Key POS Keyboard . . . . . . . . . . . . . 1‐18

NCR 7459‐K317/K318 Keyboard Filler Plate . . . . . . . . . . . . . 1‐18

Printers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐19

NCR 7167 Thermal Receipt and Impact Slip Printer . . . . . . 1‐19

NCR 7168 Thermal Receipt and Impact Slip Printer . . . . . . 1‐19

NCR 7197 Thermal Receipt Printer. . . . . . . . . . . . . . . . . . . . . 1‐20

NCR 7198 Thermal Receipt Printer. . . . . . . . . . . . . . . . . . . . . 1‐20

NCR 7162 Multifunction Impact Printer . . . . . . . . . . . . . . . . 1‐21

vi

Cash Drawers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐22

NCR 2181 Cash Drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐22

NCR 2185 Flip Top Drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐22

NCR 2186 Compact Cash Drawer. . . . . . . . . . . . . . . . . . . . . . 1‐23

Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐24

Barometric Pressure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐24

Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐24

Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐24

Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐25

7606 Terminal Power Requirements . . . . . . . . . . . . . . . . . . . . . . . 1‐25

Peripheral Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐25

AC Store Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐25

TComponent Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐26

Shipping Weight Estimate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐27

Service Clearance Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐27

Airflow Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‐28

Appendix A: Transient Protection

NCR RealPOS 82XRT Terminal Site Preparation

IntroductionThis document provides the information necessary to prepare a site to NCR

specifications prior to installing an NCR RealPOS 82XRT Terminal (also referred to as

the NCR 7606). Prepare the site properly before installing the terminal because site

preparation deficiencies may be difficult to detect and correct after installation.

The NCR 7606 consists of separate pieces that may be combined in a variety of

configurations. Certain combinations are mutually exclusive. You must determine the

equipment that will actually be installed before proceeding with the site preparation.

2 NCR RealPOS 82XRT Terminal Site Preparation

Model Numbers

Major Model CPU

7606‐1002 Intel Celeron G540, 2.5 GHz, 2GB DDR3 1033MHz memory, Diskless,

80Plus Gold Power Supply, US power cord only, Beige


80Plus Gold Power Supply, US power cord only, Charcoal


UPS Ready, Beige

7606‐1302 Intel Pentium G850, 2.9 GHz, 2GB DDR3 1033MHz memory, Diskless,

80Plus Gold Power Supply, Beige

7606‐1307 Intel Pentium G850, 2.9 GHz, 2GB DDR3 1033MHz memory, Diskless,

80Plus Gold Power Supply, Beige

7606‐1507 Intel Core‐i3 2120, 3.3 GHz, 2GB DDR3 1033MHz memory, Diskless,

80Plus Gold Power Supply, Charcoal

7606‐1707 Intel Core‐i5 2400, 3.1 GHz, 2GB DDR3 1033MHz memory, Diskless,

80Plus Gold Power Supply, Charcoal

NCR RealPOS 82XRT Terminal Site Preparation 3

Customer ResponsibilitiesBefore installing the system, the customer must perform or provide the following:

• When required by NCR, provide the NCR Customer Services representative with

appropriate drawings that indicate:

• Equipment location

• Site wiring (power and communications, paths and lengths)

• Location of other equipment that may generate electrical noise, electromagnetic

interference, or heat

• Make building alterations necessary to meet wiring and other site requirements

• Provide and install all communications cables, wall jacks, special connectors, and

associated hardware

• Provide and install necessary power distribution boxes, conduits, grounds,

lightning protection devices, and associated hardware

• Ensure all applicable codes, regulations, and laws (including, but not limited to,

electrical, building, safety, and health) are met

• Provide and install auxiliary power or other equipment as required

• Provide storage or service areas as required

• Meet all system/unit environmental requirements

• Provide and install floor coverings and environment systems that limit or control

static electricity build‐up and discharge

In general, keep the NCR equipment area free from dust, smoke, lint, and other

particles. Restrict smoking, eating, and drinking around the equipment. Avoid

locating the equipment near other machines that generate ink, carbon, and paper dust

particles.


Third Party Peripheral CertificationThird party peripherals must be certified with the POS terminal or a potential ESD

issue can occur. Third party peripherals include any electrically powered devices

connected to the POS terminal that is not an NCR branded product or a certified

solution advocated by NCR. Examples of third party products include printers,

external CD‐ROM drives, cash drawers, cigarette boxes, pin pad devices, etc.

Peripherals tend to be less sensitive to electrostatic damage when directly grounded

through their power cords. If the peripheral is powered by the terminal and has no

dedicated ground, then all of the ESD energy is coupled into the port connection.

Some devices may require the use of an in‐line galvanic isolator/surge protector in

order to prevent problems.

The NCR TPP/SCER process is designed to evaluate third party peripherals and

determine whether additional protective devices are needed.

The NCR Workstation and Peripherals AC Wiring Guide (BST0‐2115‐53) contains

additional information on this subject.

LAN CommunicationsThe NCR 7606 Terminal supports Ethernet 10/100/1000baseT Local Area Network

(LAN) communication protocol. For Ethernet communications wiring specifications,

refer to the NCR Ethernet Communication Wiring Guide (BST0‐2118‐82).


Dimensions

Base Unit

Integrated Terminal

30597

340 mm(13.4 in.)

394 mm(15.5 in.)

115 mm(4.5 in.)

30598

442 mm(17.4 in.)

B

472 mm(18.6 in.)

500 mm(19.7 in.)

A

508 mm(20.0 in.)

673 mm(26.5 in.)

Dimension 5964 (12”) 5954 (15”)

612 mm(24.1 in.)

A

B

500 mm(19.7 in.)

570 mm(22.4 in.)

608 mm(23.9 in.)

5965 (15”) 5943 (12”)

630 mm(24.8 in.)

525 mm(20.7 in.)


Integrated Terminal w/Cash Drawer

30599

442 mm(17.4 in.)

B

472 mm(18.6 in.)

500 mm(19.7 in.)

A

622 mm(24.5 in.)

673 mm(26.5 in.)

Dimension 5964 (12”) 5954 (15”)

612 mm(24.1 in.)

A

B

673 mm(24.2 in.)

690 mm(27.2 in.)

608 mm(23.9 in.)

5965 (15”) 5943 (12”)

630 mm(24.8 in.)

645 mm(25.4 in.)


7459-K320 Vertical Mount

30620

386 mm(15.2 in.)

378 mm(14.9 in.)198 mm

(7.8 in.)


5954 15-Inch DynaKey

Standard Remote Table Top Mount (5964-K030/K031)

23875a

495 mm(19.5 in.)

335 mm(13.2 in.)

295 mm(11.6 in.)

507 mm(20.0 in.)

DynaKey w/MSR

DynaKey w/o MSR


NCR 5964-K038/K039 Checkstand Mount

The Checkstand Mount is fully adjustable between the minimum and maximum

dimensions that are illustrated below. The DynaKey can also be rotated right and left

of center (shown) by approximately 90 degrees, as well as tilted from a vertical

position to approximately 45 degrees (shown).

19909b

213 mm(8.4 in.)

216 mm(8.5 in.)

400 mm(15.75 in.)

330 mm(13.0 in.)

370 mm(14.5 in.)

480 mm(19.0 in.)

38 mm1.5 in.

7.6.mm0.30 in.

70 mm2.75 in.

89 mm3.5 in.

114 mm4.25 in.


NCR 5942 12.1-Inch LCD

NCR 5943 12-Inch LCD

19810b

306 mm(12.0 in.)

304 mm(11.9 in.)

190 mm(7.5 in.)

133 mm(5.25 in.)

165 mm(6.5 in.)

47 mm(1.9 in.)

13 mm(0.5 in.)

229 mm(9.0 in.)

280 mm(11.0 in.)

292 mm(11.5 in.)

254 mm(10.0 in.)

292 mm(11.5 in.)

329 mm(12.9 in.)


NCR 5964 12-Inch Touch LCD

Standard Remote Table Top Mount (5964-K031/032)

21209a


NCR 5966 15-Inch Touch LCD

NCR 5966 with Table Top Mount

NCR 5966 with 5964-K030/K031 Table Top Mount

27328

220 mm(8.7 in.)

400 mm(15.7 in.)

358 mm(14.1 in.)

394 mm(15.5 in.)

220 mm(8.7 in.)

180 mm(7.1 in.)

27327

220 mm(8.7 in.)

400 mm(15.7 in.)

358 mm(14.1 in.)

394 mm(15.5 in.)

230 mm(9.0 in.)

254 mm(10.0 in.)


NCR 5982 6.5-Inch Color LCD

23158

174 mm(6.9 in.)

140 mm(5.5 in.)

192 mm(7.6 in.)

140 mm(5.5 in.)


Customer Displays

NCR 5975-1xxx 2x20 Remote Customer Display

22915

180 mm(7.1 in.)

216 mm(8.5 in.)

123 mm(4.8 in.)

81 mm(3.2 in.)

151 mm(5.9 in.)


NCR 5975-2xxx Graphical Remote Customer Display

22916

224 mm(8.9 in.)

229 mm(9.0 in.)

123 mm(4.8 in.)

93 mm(3.7 in.)

151 mm(5.9 in.)


NCR 5976-1xxx 2x20 Remote Customer Display

30824

159 mm(6.6 in.)

80 mm(3.2 in.)

123 mm(4.8 in.)

211 mm(8.3 in.)

153 mm(6.0 in.)


Keyboards

NCR 5932-2xxx 64-Key POS Keyboard

NCR 5932-5xxx USB Big Ticket POS Keyboard

11413a

184 mm(7.2 in.)

335 mm(13.2 in.)

42 mm(1.7 in.)

19716a

184 mm(7.2 in.)

455 mm(17.9 in.) 42 mm

(1.7 in.)


NCR 5932-6xxx 104-Key Compact Alphanumeric Keyboard

NCR 5932-7xxx PS/2 78-Key POS Keyboard

NCR 7459-K317/K318 Keyboard Filler Plate

21317a

184 mm(7.25 in.)

365 mm(14.4 in.)

45 mm(1.7 in.)

22049a

188 mm(7.4 in.)

283 mm(11.1 in.)

47 mm(1.9 in.)

25207

432 mm(17 in.) 185 mm

(7.3 in.)


Printers

NCR 7167 Thermal Receipt and Impact Slip Printer

NCR 7168 Thermal Receipt and Impact Slip Printer

19711g

190 mm(7.5 in.)

174 mm(7.0 in.)

262 mm(10.3 in.)

316 mm(12.5 in.)

275 mm10.8 in.

23537a

OK

346 mm(13.6 in.)

190 mm(7.5 in.)

181 mm(7.1 in.)

300 mm(11.8 in.)


NCR 7197 Thermal Receipt Printer

NCR 7198 Thermal Receipt Printer

19712g

146 mm(5.75 in.)

156 mm(6.25 in.)

184 mm(7.25 in.)

255 mm10.1 in.

23834c

256 mm(10.1 in.)

145 mm(5.7 in.)

220 mm(8.7 in.)

139 mm(5.5 in.)


NCR 7162 Multifunction Impact Printer

15410a

250 mm(11.7 in.)

297 mm(11.7 in.)

191 mm(7.5 in.)

142 mm(5.6 in.)


Cash Drawers

NCR 2181 Cash Drawer

NCR 2185 Flip Top Drawer

24799

762 mm(30.0 in.)

442 mm(17.4 in.)

467 mm(18.7 in.)

117 mm(4.6 in.)

w/feet:

127 mm(5.0 in.)

23535

460 mm18.1 in.

254 mm10.0 in.

172 mm6.8 in.


NCR 2186 Compact Cash Drawer

23150a

700 mm(27.6 in.)

415 mm(16.3 in.)

411 mm(16.2 in.)

110 mm(4.3 in.)


Environmental Requirements

Barometric PressureThe terminal operates within the following barometric pressure conditions:

• Maximum operating altitude: 3,000 m (9,843 ft.)

• Operating range of pressure: 105 to 69 kPa (15.2 to 10.0 lb./in.)

TemperatureThe terminal operates over the temperature ranges shown below. Avoid continuous

operation at, near the indicated temperature extremes, or in locations where the

temperature changes beyond the restrictions.

HumidityThe terminal operates within the humidity ranges shown below. Avoid continuous

operation at, near the indicated humidity extremes, or in locations where the

humidity changes beyond the restrictions. Never expose the terminal to

condensation.

Temperature Parameter Restriction

Operating 5C to 40C (41F to 104F), dry bulb

Storage ‐10C to 50C (14F to 122F), three months

Shipping ‐40C to 60C (‐40F to 140F), one week

Humidity Type Restriction

Relative 10% to 90%

Maximum change rate 10%/60 minutes

Storage 10% to 90% relative humidity, three months

Shipping 5% to 95% relative humidity, one week


Electrical Requirements

7606 Terminal Power RequirementsThe terminalʹs external power supply has a maximum output of 150 Watts and

provides power to the terminal and its powered peripherals.

Caution: Locate the power supply away from other electrical equipment, away from

heat sources, away from possible liquid spills, and where there is adequate clearance

for cooling.

Note: The RealPOS 82XRT does not offer an AC convenience outlet for CRT power. A

separate country‐specific power cord must be ordered separately. Available NCR

power cords are described in the System Cables section.

Peripheral Power RequirementsThe number of peripherals that the terminal can support is dependent upon which

peripherals are connected. For planning purposes, use the RealPOS 82XRT (7606)

Release 1.0 Power Matrix (B005‐0000‐2089) for details on total power distribution.

Note: This file requires Microsoft Excel to run.

AC Store Wiring RequirementsThe customer must provide suitable AC power for the terminals, associated

equipment, and devices. We recommend a dedicated unswitched power line

dedicated to the NCR equipment installation. Refer to the NCR Workstation and

Peripherals AC Wiring Guide (BSTO‐2115‐53) for store AC wiring requirements. The

AC outlet must be installed near the terminal and easily accessible to the operator.

Range Nominal Vrms Minimum Vrms Maximum Vrms

LOW (115) 100‐127 90 136

HIGH (230) 200‐240 180 265


TComponent Weights

Terminal Component Weight kg (lbs.)

7606 Terminal w/Batteries 10.7 (23.5)

7606 Terminal w/o Batteries 8.8 (19.3)

Integrated Tray Kit 8.6 (18.0)

2181 Cash drawer 6.0 (13.3)

2185 Cash Drawer 12.3 (27.0)

2186 Cash drawer 12.3 (27.0)

64‐Key Keyboard 0.9 (1.9)

78‐Key Keyboard 1.1 (2.4)

Big Ticket Keyboard 1.0 (2.15)

104‐Key Compact Keyboard 1.4 (3.0)

5975‐1xxx Customer Display 11.9 (26.5)



5942 12.1” Touch LCD 2.8 (6.2)

5943 12.1” LCD 2.1 (4.8)

5965 Touch LCD 4.0 (8.8)

5966 Touch Monitor 5.4 (11.9)

7167 Receipt/Impact Printer 4.5 (10.0)


7197 Thermal Receipt Printer 1.5 (3.4)

7198 Thermal Receipt Printer 2.2 (4.9)


Shipping Weight EstimateTo obtain the total maximum weight of a specific configuration, add the weights of

the appropriate individual components. The following table provides an example.

Service Clearance Requirements

Terminal Component Weight kg (lbs.)

Integrated Terminal w/Batteries 13.0 (35.0)

5942 12.1‐Inch LCD 2.8 (6.2)

5975‐2xxx Customer display 0.5 (1.2)

64‐Key keyboard 0.9 (1.9)


Total 21.7 (54.3)

Miscellaneous items and

shipping materials

5.2 (11.5)

Shipping total 26.9 (65.8)

DeviceAbove mm (in.)

Left Side mm (in.)

Right Side mm (in.)

Front mm (in.)

Behind mm (in.)

Terminal Base ‐ ‐ 100 (4.0) 100 (4.0) 100 (4.0)

Keyboard ‐ ‐ 100 (4.0) ‐ ‐

Cash Drawer ‐ ‐ ‐ 330 (13.0) ‐

7162 Printer 325 (13.0) 300 (12.0) ‐ 100 (4.0) 25 (1.0)

7167 Printer 305 (12) 305 (12) ‐ ‐ ‐

7168 Printer 305 (12) 305 (12) ‐ ‐ ‐

7197 Printer 267 (10.5) ‐ ‐ ‐

5953 DynaKey 50 (2) 25 (1) 100 (4) ‐ ‐

5942/43 LCD 50 (2) 25 (1) 25 (1.0) ‐ ‐

5964 Touch LCD 50 (2) 25 (1) 100 (4) ‐ ‐

5975 Display 25 (1.0) ‐ 25 (1.0) ‐ ‐


Airflow RequirementsDo not block the air vents on the terminal. These vents are necessary for cooling.

Do not place the terminal in an enclosed area where sufficient ventilation is not

available. Leave at least 100 mm (4 inches) of clearance on sides where air vents are

located.

When the terminal is wall‐mounted, the rear cover must have at lease 6 mm (0.25 in.)

clearance from the wall. The mounting mechanism must not block the vent holes on

the rear cover.

24089a

Appendix A: Transient Protection

AC Power Line Transient ProtectionIn the process of power distribution, transient electrical energy (including, but not

limited to, lightning strikes, intermittent short circuits, and switching transients) can

be introduced onto power lines. Such transient energy can be very damaging to

electronic hardware, and can also cause data corruption. Under these circumstances,

NCR recommends the use of AC power transient suppressors. Such protection

devices are intended to guard against power line transients that can result in

hardware damage and various system or program errors.

Improvement of any deficiencies in power quality is a customer responsibility.

Malfunction and/or component failure as a result of power quality problems are/is

not covered by the NCR Maintenance Agreement. NCR accepts no liability for any

such occurrence nor for its consequences.

When power transient suppression is required, the suppressors used should meet the

following minimum requirements:

• Dissipate energy to match the appropriate location categories as defined by IEEE

Standard C.62.41.2‐2002.

• Be of the voltage limiting (clipping), or tracking filter type. The suppressor must

not clamp the voltage to zero, and must self‐recover after the passage of the

transient. The suppressor may be of the hybrid type construction that makes use

of various technologies in order to meet speed and dissipation requirements.

• TranUpon failure, exhibit a positive indication of its failure such as a blown fuse

or tripped breaker.

• Be listed by the accepted safety organization for the country involved (UL, CSA,

VDE, ETL, and so on) and the installation must conform to local, state, and

national electrical

2

Data Line Transient ProtectionThe nature of the transient phenomenon may extend to the data communication lines

connected to this equipment. It is the responsibility of the customer to install and

connect a data line transient suppression system to correct or prevent any

deficiencies. Such systems must meet the following minimum requirements:

• Be of the voltage limiting type and must self‐recover after passage of the transient.

• Must be designed to avoid signal degradation for the given interface they are

attached to.

• Be installed in accordance with all applicable local, state, and national electrical

codes and regulation.

Note: NCR provides a full line of both AC power and data line transient surge

suppressors to protect your RealPOS system and reduce downtime and extend the

life of the RealPOS Retail Solution. For sizing and product information, please call

NCR Site Preparation Services at 800‐257‐0458.

The following product offerings are available from NCR Site Preparation Services:

• UPS ‐Uninterruptible Power Systems

• Provides battery backup for power outages and brownouts.

• Includes AC and data line surge protection.

• If needed, certain models provide basic voltage regulation.

• Small size provides easy installation.

• Line Conditioners / Filters

• Incorporates an Isolation transformer or filter that provides 100% isolation

from disturbances on the incoming AC power line.

• Removes EMI/RFI noise that causes equipment lockups.

• Reduces common mode noise issues and surges/transients.

• Significantly reduces POS downtime and component failure.

• Transient Voltage Surge Suppressors

Provides protection from catastrophic AC surges/transients.

• Provides data line protection from catastrophic surges that can migrate onto

the data line and network.

2086b

Documents

Transcript of 2086b