2014 TOOLING REFERENCE GUIDE VERSION 7 - … 2014v7.pdf · Page 5 4232 E. Magnolia St., Phoenix,...

2014TOOLING REFERENCE

GUIDEVERSION 7.0

BLANK PAGE

ALL TOOLING SHOWN IS GREAT LAKES TOOLING

2014

Ver

sion

7.0

4232 E. Magnolia St., Phoenix, Arizona 85034 U.S.A. PH: (602)470-1911 Fax: (602)470-1916 Website: www.uniquemachine.com Email: [email protected]

TE

CH

NIC

AL

NO

TE

S

.750

5.739

4.000

7.500

4.000

.750

2.933

4.114

.590

.620

.750 COPE

U-460

U-410/U-430

U-410/U-430

STICK.750

.9304.981

1.250 BORE

3.000

1.900

.040SHIM

.733

.984 [25.00mm]

SPACER

.984 [25.00mm]

MACHINE MODEL : ALL 250’S

It is extremely important that this spacer be on thestack between small & large diameter tools.* Spacer size varies between machine models. Please contact Unique to avoid bodily injury or machine damage.

Note: In order to utilize arching capabilities of the250GT2, the Rail, Cope and Trim Cutter must

maintain a contant OD of 4.00”

• When machining doors on the Unique Model 250:

1. Watch Training Video prior to operation.

2. Feed materials at a brisk pace. Feeding to slow will prematurely wear tooling.

3. When arching rails, feed thru 1/3 of the arch, pull straight back & climb cut the remainder of the arch. (NOTE: This may take some pratice to become efficient)

4. For beginners, an easy method to arch a rail is to insert the rail blank until it touches the stop. Back the blank out roughly 1/4-1/2”. Cut the arch then push the cut part in again until it touches the stop and finish the cut. (NOTE: This method is not ideal for production but it is suitable for training purposes)

· All Unique 250’S come standard with a complete set of tooling and one arching template.For shops with many profiles, an additional turret is recommended for ease of setup but is not required.

Always install inserts using proper torque rating for tool.

4232 E. Magnolia St., Phoenix, Arizona 85034 U.S.A. PH: (602)470-1911 Fax: (602)470-1916


2014

Ver

sion

7.0

Website: www.uniquemachine.com Email: [email protected]

• When machining cope/tenon profiles on the Unique Model 265 or 310/311:

1. Always use a backer board.

2. Backer board should be “notched” to ensure sufficient part clamping.

3. Feed the material quickly past the cutter head to help extend the life of the tooling.

• All Unique coping machines are shipped without tooling. Customer tooling will be setup on new machine orders iftooling is recieved at Unique one week prior to machine delivery date. For multiple cutter models with many profiles, anadditional turret is recommended for ease of setup but is not required.


3.000

4.000

2.354

.984 [25.00mm]

1.900

U-410/U-430COPE.750

.750SHAKERCOPE

.984 [25.00mm]

1.250 BORE

MACHINE MODEL : 265 & 310/311

TE

CH

NIC

AL

NO

TE

S


2014

Ver

sion

7.0


.179

R.281

.087

.266

.218 [5.53mm]

U-410.750 STICK

.280

.500R.031TYP.

U-410STICK

.189

.363

.198 [5.03mm]

.500

.087

.750

.281 R.281

R.031 (TYP)

FOR MODELS 250/265/310/311

U410 Profile

0.250” Tenon

.284

R.284

.245

.495

R.031TYP.

.750 COPEU-410

RAIL INSERTI810-09800-1000 CWI810-09800-2000 CCW

COPE INSERTI810-09801-1000 CWI810-09801-2000 CCW

5.0 mm Tenon

5.2 mm Tenon 5.5 mm Tenon







4.000

3.000

1.900

.984 [25.00mm]

.984 [25.00mm]

1.250 BORE

.185

R.281

.087

.272

.206 [5.23mm]

U-410.750 STICK

.280

.500R.031TYP.

.282R.284

.750 U-410COPE

.495R.031TYP. .187

.273

.085

.205 [5.20mm]

U-410COPE

.191

.362

.197 [5.00mm]

.495

.281

R.284

R.031 (TYP)

.085

.750

.282R.284

.750 U-410COPE

.495R.031TYP. .181

.267

.085

.217 [5.50mm]

Rail Cutter Body - C210-35138-1000 CWRail Cutter Body - C210-35138-2000 CCW

Cope Cutter Body - C210-35139-1000 CWCope Cutter Body - C210-35139-2000 CCW

All of the profiles belowrun in these tool bodies

CO

PE

& R

AIL

PR

OF

ILE

S



2014

Ver

sion

7.0


FOR MODELS 250/265/310/311

U430 Profile4.000

3.000

1.900

.984 [25.00mm]

.984 [25.00mm]

1.250 BORE

0.250” Tenon



5.0 mm Tenon







.185

R.187

.156

.087

.116

.206 [5.23mm]

STICKU-430.750

R.031TYP. .500

.281

COPEU-430

R.190

.750

R.031TYP.

.284

.087

.117

.187.495

.214

.205 [5.20mm]

.750

R.031TYP.

R.187

.281

.250

.500

U-430RAIL

.245

.284

.495

R.190

R.031TYP.

.750 COPEU-430




.179

R.187

.156

.087

.110

.218 [5.53mm]

STICKU-430.750

R.031TYP. .500

.281

COPEU-430

R.190

.750

R.031TYP.

.284

.087

.111

.181.495

.214

.217 [5.50mm]

CO

PE

& R

AIL

PR

OF

ILE

S

.500

.189U-430

R.031TYP.

.281 .087

.156

.198 [5.03mm]

.120

.750 STICK

R.187

.495

COPEU-430

R.031TYP.

R.190

.191

.121

.197 [5.00mm]

.284

.087

.214



2014

Ver

sion

7.0


FOR MODELS 250/265/310/311

U336 Profile

0.250” Tenon



5.0 mm Tenon








4.000

3.000

1.900

.984 [25.00mm]

.984 [25.00mm]

1.250 BORE

R.185

R.031TYP.

R.190

.750U-336COPE

.376

.245

.495

.376

U-336COPE.750

R.185

R.190

.495 .187.205 [5.20mm]

.358

R.031TYP.




STICKU-336

R.031 TYP.

U-336COPE

R.031 TYP.

.500R.031TYP.

.185

STICKU-336.750

R.188

.169

.372R.188

.206 [5.23mm]

.191

.179

R.188

.169

R.188

.218 [5.53mm]

.185

.500

STICKU-336.750

.370

R.031 TYP.

.217 [5.50mm]

.373

.166.186

.181.495

U-336COPE.750

R.185

R.190

R.031 TYP.

CO

PE

& R

AIL

PR

OF

ILE

S



2014

Ver

sion

7.0


.495

.378

.156.085

.111

.181

.217 [5.50mm]

COPE.750 U-600

R.031TYP.

R.247R.252

.495

R.249

.378

.156.085

.121

.191

.197 [5.00mm]

.750

R.031TYP.

R.248

U-600 COPE

FOR MODELS 250/265/310/311

U600 Profile4.000

3.000

1.900

.984 [25.00mm]

.984 [25.00mm]

1.250 BORE

0.250” Tenon



5.0 mm Tenon








.110

.087

.500R.031TYP.

.179

STICKU-600.750

.156

.375R.250

.218 [5.53mm]

R.250

.110

.087

.500R.031TYP.

.179

STICKU-600.750

.156

.375R.250

.218 [5.53mm]

R.250

.495

.378

.156.085

.111

.181

.217 [5.50mm]

COPE.750 U-600

R.031TYP.

R.247R.252

R.250R.250

.375

.500R.031TYP.

.750 RAILU-600 .250

R.248

R.031TYP.

.750 COPEU-600

R.253

.378

.495

.245

.120

.087

.500R.031TYP.

.189

.750

R.250

.156

.375

.198 [5.03mm]

U-600 STICK

R.250

CO

PE

& R

AIL

PR

OF

ILE

S





2014

Ver

sion

7.0


FOR MODELS 250/265/310/311

U410 GlassProfile



U430 GlassProfile



U410/U430 Glass Profile

R.284

.750

.284

.251

.085R.190

R.031TYP.

.284

.750 .087

.095

.214

.087

.250.750

.281

.500

R.187

.156

.087

.094.750

.281

.500

4.000

1.181 [30.00mm]

.984 [25.00mm]

3.000

1.181 [30.00mm]

.984 [25.00mm]

1.250BORE




CO

PE

& R

AIL

PR

OF

ILE

S



2014

Ver

sion

7.0


FOR MODELS 250/265/310/311

U336 GlassProfile



U600 GlassProfile



U336/U600 Glass Profile

.116

.087

.500

.750.156

.375R.250

R.250

R.031 TYP.

.378

.156.085

.117.750

R.247R.252

CO

PE

& R

AIL

PR

OF

ILE

S

CUTTER NUMBER210-30565-20003.000

1.250BORE

.984 [25.00mm] 1.181

[30.00mm]

4.005

7 3.000

1.181 [30.00mm]

.984 [25.00mm]

.493

.413.750 .169

.366R.188R.188

R.031TYP.

R.031TYP.

R.188R.187

.366

.491

.168

.412

.750





2014

Ver

sion

7.0


3.000

4.000

SHAKERSTICK

SHAKERCOPE

.984 [25.00mm]

.984 [25.00mm]

1.900

1.250 BORE

FOR MODELS 250/265/310/311

S1 Shaker Profiles

0.250” Tenon



5.0 mm Tenon








.245COPE

R.031TYP.

.750.031

.031

SHAKER

.495

.250.031

.750 RAIL

.031

.500

SHAKER

R.031TYP.




STICKSHAKER.750

.500

.276

.276

.198 [5.03mm]

.031.031

R.031 (TYP)

.495

.031

SHAKERCOPE

.277

.277

.031

.197 [5.00mm].750

R.031 (TYP)

STICK

R.031TYP.

SHAKER.750

.500

.272

.272

.206 [5.23mm]

.031.031

.495

.031

R.031TYP.

SHAKERCOPE

.273

.273

.031

.205 [5.20mm].750

STICK

R.031TYP.

SHAKER.750

.500

.031.031

.266

.266

.218 [5.53mm]

.495

.750

R.031TYP.

SHAKERCOPE

.267

.267

.217 [5.50mm]

.031.031

CO

PE

& R

AIL

PR

OF

ILE

S



2014

Ver

sion

7.0


3.000

4.000

SHAKERSTICK

SHAKERCOPE

.984 [25.00mm]

.984 [25.00mm]

1.900

1.250 BORE

0.250” Tenon



5.0 mm Tenon








FOR MODELS 250/265/310/311

S2 Shaker Profiles

.031

.031

.245.750

.031

R.031TYP.

SHAKERCOPE

.495

.750

.031

.250

.031

.500R.031TYP.

SHAKERRAIL

.031

STICK

R.031TYP.

SHAKER.750

.500

.266

.266

.218 [5.53mm]

.031

.031.031

.495

.750

R.031TYP.

SHAKERCOPE

.267

.267

.217 [5.50mm]

.031.031

.031

STICK

R.031TYP.

SHAKER.750

.500

.272

.272

.206 [5.23mm]

.031.031

.031

.495

.031

R.031TYP.

SHAKERCOPE

.273

.273

.031

.031

.205 [5.20mm].750

STICKSHAKER.750

.500

.276

.276

.198 [5.03mm]

.031.031

.031R.031 (TYP)

.495

.031

SHAKERCOPE

.277

.277

.031

.031

.197 [5.00mm].750

R.031 (TYP)

CO

PE

& R

AIL

PR

OF

ILE

S





2014

Ver

sion

7.0


.495

SHAKERCOPE

.277

.277

.197 [5.00mm].750

R.031 (TYP)

FOR MODELS 250/265/310/311

S3 Shaker Profiles3.000

4.000

SHAKERSTICK

SHAKERCOPE

.984 [25.00mm]

.984 [25.00mm]

1.900

1.250 BORE

0.250” Tenon



5.0 mm Tenon








.250

.500

.750

R.031TYP.

RAILSHAKER

R.031TYP.

.750SHAKERCOPE .245

.495

STICK

R.031TYP.

SHAKER.750

.500

.266

.266

.218 [5.53mm]

.495

.750

R.031TYP.

SHAKERCOPE

.267

.267

.217 [5.50mm]




STICKSHAKER.750

.500

.276

.276

.198 [5.03mm]

R.031 (TYP)

STICK

R.031TYP.

SHAKER.750

.500

.272

.272

.206 [5.23mm]

.495R.031TYP.

SHAKERCOPE

.273

.273

.205 [5.20mm].750

CO

PE

& R

AIL

PR

OF

ILE

S



2014

Ver

sion

7.0


S1 Shaker Glass



.750.375

.500

.250

.123.128

R.031 TYP.

R.064

.124

.750

.500

.245

.375

.125.125

R.062R.031TYP.

FOR MODELS 250/265/310/311

Shaker Glass Profile

CO

PE

& R

AIL

PR

OF

ILE

S

.984 [25.00mm].750

117

.117

1.181 [30.00mm]

4.500

4.000

1.250 BORE

.984 [25.00mm].750

.117

1.181 [30.00mm]

4.490CUTTER NUMBER

210-30562-2000





2014

Ver

sion

7.0


.282R.284

.750 U-410COPE

.495R.031TYP. .187

.273

.085

.205 [5.20mm]

INSERT

BACKER PLATE

TOP VIEW OF CUTTER BODYBACKER PLATE REQUIRED WITH INSERT

INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE


U-410COPE

.191

.362

.197 [5.00mm]

.495

.281R.284

R.031 (TYP)

.085

.750

.282R.284

.750 U-410COPE

.495R.031TYP. .181

.267

.085

.217 [5.50mm]

FOR MODELS 265/310/311

U410 Profile

0.250” Tenon

.284

R.284

.245

.495

R.031TYP.

.750 COPEU-410


BACKER REQUIREDWITH THIS TOOLI850-15264-1000 CWI850-15264-2000 CCW

5.0 mm Tenon


COPE INSERTPart number isavailable upon request



BACKER REQUIREDWITH THIS TOOLPart number isavailable upon request



SG C

OP

E P

RO

FIL

ES

1.250BORE

6.000 MAXIMUM CUTTING DIAMETER

4.819 MINIMUM CUTTING DIAMETER

1.181 [30.00mm]

TABLE BED

.591 [15.00mm]MAXIMUM PROFILE

DEPTH

1.299 [33.00mm]

2 WC215-09C215-09





2014

Ver

sion

7.0


1.250BORE



1.181 [30.00mm]

TABLE BED


DEPTH

1.299 [33.00mm]

2 WC215-09C215-09

COPEU-430

R.190

.750

R.031TYP.

.284

.087

.111

.181.495

.214

.217 [5.50mm]


U430 Profile

0.250” Tenon


5.0 mm Tenon


COPE INSERTI810-37853-2000 CCW



COPEU-430

R.190

.750

R.031TYP.

.284

.087

.117

.187.495

.214

.205 [5.20mm]

.245

.284

.495

R.190

R.031TYP.

.750 COPEU-430

INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE



BACKER REQUIREDWITH THIS TOOLI850-37853-2000 CCW



SG C

OP

E P

RO

FIL

ES



.495

COPEU-430

R.031TYP.

R.190

.191

.121

.197 [5.00mm]

.284

.087

.214


2014

Ver

sion

7.0


U-336COPE

R.031 TYP.

.282R.284

.750 U-410COPE

.495R.031TYP. .187

.273

.085

.205 [5.20mm]

INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE







U336 Profile

0.250” Tenon

.284

R.284

.245

.495

R.031TYP.

.750 COPEU-410


5.0 mm Tenon





.179

R.188

.169

R.188

.218 [5.53mm]

.185

.500

STICKU-336.750

.370

R.031 TYP.

SG C

OP

E P

RO

FIL

ES

1.250BORE



1.181 [30.00mm]

TABLE BED


DEPTH

1.299 [33.00mm]

2 WC215-09C215-09





2014

Ver

sion

7.0


INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE







U600 Profile

0.250” Tenon


5.0 mm Tenon





COPEU-430

R.190

.750

R.031TYP.

.284

.087

.117

.187.495

.214

.205 [5.20mm]

.245

.284

.495

R.190

R.031TYP.

.750 COPEU-430

.495

.378

.156.085

.111

.181

.217 [5.50mm]

COPE.750 U-600

R.031TYP.

R.247R.252

.495

R.249

.378

.156.085

.121

.191

.197 [5.00mm]

.750

R.031TYP.

R.248

U-600 COPE

SG C

OP

E P

RO

FIL

ES

1.250BORE



1.181 [30.00mm]

TABLE BED


DEPTH

1.299 [33.00mm]

2 WC215-09C215-09




2014

Ver

sion

7.0


INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE







S1 Shaker Profiles

0.250” Tenon


5.0 mm Tenon





.245COPE

R.031TYP.

.750.031

.031

SHAKER

.495

.495

.031

R.031TYP.

SHAKERCOPE

.273

.273

.031

.205 [5.20mm].750

.495

.750

R.031TYP.

SHAKERCOPE

.267

.267

.217 [5.50mm]

.031.031

.495

.031

SHAKERCOPE

.277

.277

.031

.197 [5.00mm].750

R.031 (TYP)

SG C

OP

E P

RO

FIL

ES

1.250BORE



1.181 [30.00mm]

TABLE BED


DEPTH

1.299 [33.00mm]

2 WC215-09C215-09





2014

Ver

sion

7.0


INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE







S2 Shaker Profiles

0.250” Tenon


5.0 mm Tenon





.031

.031

.245.750

.031

R.031TYP.

SHAKERCOPE

.495

.495

.750

R.031TYP.

SHAKERCOPE

.267

.267

.217 [5.50mm]

.031.031

.031.495

.031

R.031TYP.

SHAKERCOPE

.273

.273

.031

.031

.205 [5.20mm].750

.495

.031

SHAKERCOPE

.277

.277

.031

.031

.197 [5.00mm].750

R.031 (TYP)

SG C

OP

E P

RO

FIL

ES

1.250BORE



1.181 [30.00mm]

TABLE BED


DEPTH

1.299 [33.00mm]

2 WC215-09C215-09




2014

Ver

sion

7.0


INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE







S3 Shaker Profiles

0.250” Tenon


5.0 mm Tenon





R.031TYP.

.750SHAKERCOPE .245

.495

.495

.750

R.031TYP.

SHAKERCOPE

.267

.267

.217 [5.50mm]

.495

SHAKERCOPE

.277

.277

.197 [5.00mm].750

R.031 (TYP)

.495R.031TYP.

SHAKERCOPE

.273

.273

.205 [5.20mm].750

SG C

OP

E P

RO

FIL

ES

1.250BORE



1.181 [30.00mm]

TABLE BED


DEPTH

1.299 [33.00mm]

2 WC215-09C215-09





2014

Ver

sion

7.0


FOR MODELS 250

Panel Profiles


U264 Profile

PANEL INSERTI810-09808-1400 CW

I810-09808-2400 CCW

U303 Profile

U339Profile U339G Profile


I810-09808-2700 CCW


I810-09808-2200 CCW


I810-09808-2900 CCW

.3751.750

R1.250

.375

.594

.831

.245.130

R1.250

.750 .620 U-339G

.750.245

R1.250

.130

.831

.375

R.150

1.748

U-264

R.1501.743

R.150

R.150R.150

.750 U-303

R.150R.150.375

.245.130

.831

.245.130

R1.250

.750

.831

R1.250

1.750

U-339

R.188

.375PA

NE

L P

RO

FIL

ES


2014

Ver

sion

7.0


FOR MODELS 250

Panel Profiles

U339S Profile U416 Profile

U429 Profile U429S Profile


.750.245

R1.500

.375

1.750

.831

.130

U-429

R.125

.130.245

R2.000

.750

R.150

.831

1.748

R.188

U-416

.375

.245

1.562

R.132 .414

R.928R.840

.351

.594

.844

U-339S.596

PAN

EL

PR

OF

ILE

S


I810-30283-2000 CCW


I810-09808-2600 CCW


I810-09808-2100 CCW


I810-09808-2110 CCW

.594.130

.831

.620.750.375

R1.500

1.750

.245

.375

R.125

R.055



2014

Ver

sion

7.0


FOR MODELS 250

Panel Profiles


U460 Profile U479 Profile


.750.245

.130

.375

R2.500

1.695

U-460

.831

.245.130

.750

.831

1.748

U-763

R.188

.375

R.150R.150R.150

1.746

.130

.831

.750 U-479.245

.375

.245

.594

.375

1.750

.130

.375

.831

.750 .620 U-763G

.126PA

NE

L P

RO

FIL

ES


I810-09808-2500 CCW


I810-09808-2300 CCW


I810-09808-2000 CCW


I810-09808-2120 CCW


2014

Ver

sion

7.0


FOR MODELS 250

U410 Cope Profile


U410 Rail Profile

S3 Cope Profile

RAIL INSERTI810-30265-2000 CCW

.590

1.000

CUTTER NUMBER

CUTTER NUMBER230-09809-0000

210-09808-2000CUTTER NUMBER

230-09810-2000

.040SHIM

7.500

1.886

PART FACE

4.0005.739

1.250 BORE

.921 [23.39mm]

.720

.555

1.181 [30.00mm] 1.378

[35.00mm]

3.9903.000

PART FACE 1.250 BORE

1.000 U-410COPE

.091

.091

.276R.284

1.000 U-410COPE

.495R.031TYP.

.163

.251

.087

.249 .163

R.281

.337

.250

.250U-4101.000 STICK

.281

.500

R.031TYP.

4.000

PART FACE

3.000

1.250 BORE

1.378 [35.00mm]

1.181 [30.00mm]

U-4101.000 STICK

.091

.091

1.250 BORE

3.188

3.0004.000

1.181 [30.00mm]STICK

SHAKER1.000

.091

.091

1.378 [35.00mm]

PART FACE

.495

.031

1.000SHAKER

R.031TYP.

COPE

.250

.500 .031

.249

1.181 [30.00mm]

1.250 BORE3.000

3.990

1.378 [35.00mm]

1.000SHAKERCOPE

4.178

.091

.091

PART FACE

STICK

R.031TYP.

SHAKER1.000

.500

.250

.031.500

.250

.031

S3 Rail Profile

1 IN

CH

DO

OR

S

PANEL INSERTI810-30264-1000 CWI810-30264-2000 CCW

COPE TOOL BODYC210-30266-2000 CWW

RAIL TOOL BODYC210-30265-2000 CWW



COPE TOOL BODYC210-30267-2000 CWW

RAIL TOOL BODYC210-30268-2000 CWW

1 inch Doors



2014

Ver

sion

7.0


.060SHIM

7.500

1.250 BORE

4.000

1.250

.543

.543

.685 [17.40mm]

.921 [23.39mm]

.921 [23.39mm]

1.250 BORE3.000

4.001

1.969 [50.00mm]

.109

.109

1.750

1.250 BORE3.000

3.996

1.969 [50.00mm]

.109

.109

1.750

FOR MODELS 250

U336 Rail Profile

RAIL CUTTERC210-29112-2000 CCWRAIL INSERTI810-29112-2000 CCW

U336 Cope Profile

U763Profile

COPE CUTTERC210-29113-2000 CCWCOPE INSERTI810-29113-2000 CCW

PANEL INSERTI810-09808-1000 CWI810-09808-2000 CCW

EN

TR

Y D

OO

R T

OO

LS

Top Panel Cutter Body - C210-09808-2000 CCWTrim Cutter Body - C210-27644-0000 CW/CCW

Bottom Panel Cutter Body - C210-09808-1000 CW

.495

.375

1.748

10.24°

R.188

Entry Doors


2014

Ver

sion

7.0


FOR MODELS 250

4.000

.984 [25.00mm]

1.250 BORE

1.181 [30.00mm]

REPLACEMENT INSERT NUMBERI-TRIM-GR8

4” OD HOGGER FOR ALL 250 MODELSC230-15030-2000

USED FOR PRE-ARCHING PANELS TOMACHINE ON UNIQUE SHAPE AND SAND

USED FORHOGGING RAIL ON 250GT2

REPLACEMENT INSERT NUMBERI-TRIM-GR8

2.875” OD HOGGER FOR 250GT2XSC230-28875-2000

CUTTER NUMBER

HO

GG

ER

T

OO

LS Hogger Tools

BLANK PAGE



2014

Ver

sion

7.0


TE

CH

NIC

AL

NO

TE

S

• When machining stile profiles on the Unique Model 318:

1. Always use 6.00” constant OD tooling. Tooling exceeding 6.00” OD will damage the machine and tooling. Tooling under 6.00” OD will not machine parts consistently,

2. Set the fence to the desired finished part size. (NOTE: It is not recommended to remove less than 1/32” of material or no more than 3/16” material a pass)

3. Always verify that there is sufficient hold down pressure, the machine climb cuts in the same direction as the feed direction.

• All Unique coping machines are shipped without tooling. Customer tooling will be setup on new machine ordersif tooling is recieved at Unique one week prior to machine delivery date.



2014

Ver

sion

7.0


FOR MODELS 318

U410 Profile

Rail Cutter Body - C211-26716-2000 CCW


SG S

TIL

E P

RO

FIL

ES

U-410STICK

.189

.363

.198 [5.03mm]

.500

.087

.750

.281 R.281

R.031 (TYP)

0.250” Tenon


5.2 mm Tenon




2014

Ver

sion

7.0


FOR MODELS 318

U430 Profile



SG S

TIL

E P

RO

FIL

ES

0.250” Tenon


5.2 mm Tenon

RAIL INSERTPart number isavailable upon request

.750

R.031TYP.

R.187

.281

.250

.500

U-430RAIL

.185

R.187

.156

.087

.116

.206 [5.23mm]

STICKU-430.750

R.031TYP. .500

.281


2014

Ver

sion

7.0


1.250 BORE

5.000

6.000

1.181 [30.00mm]

.216

.216

.750

"CLIMB CUTTING"

U-600STICK 2

2

FOR MODELS 318



5.0 mm Tenon

RAIL INSERTI811-32306-2100 CCWSTICK

U-336

R.031 TYP.

U336 Profile

SG S

TIL

E P

RO

FIL

ES

0.250” Tenon




2014

Ver

sion

7.0


FOR MODELS 318

U600 Profile



SG S

TIL

E P

RO

FIL

ES

1.250 BORE

5.000

6.000

1.181 [30.00mm]

.216

.216

.750

"CLIMB CUTTING"

U-600STICK 2

2

0.250” Tenon


5.0 mm Tenon


R.250R.250

.375

.500R.031TYP.

.750 RAILU-600 .250

.120

.087

.500R.031TYP.

.189

.750

R.250

.156

.375

.198 [5.03mm]

U-600 STICK

R.250


2014

Ver

sion

7.0


Shaker Profile



SG S

TIL

E P

RO

FIL

ES


S2 - 0.250”Tenon

S3 - 0.250”Tenon

S3 - 5.2 mmTenon




S1 - 0.250”Tenon

.250.031

.750 RAIL

.031

.500

SHAKER

R.031TYP.

.250

.500

.750

R.031TYP.

RAILSHAKER

STICK

R.031TYP.

SHAKER.750

.500

.272

.272

.206 [5.23mm]

.750

.031

.250

.031

.500R.031TYP.

SHAKERRAIL

.031

FOR MODELS 318



2014

Ver

sion

7.0


.750.375

.500

.250

.123

.128

R.031 TYP.

R.064

.093

1.250BORE

1.181 [30.00mm]

1.299 [33.00mm]

4.500

6.000"CLIMB CUTTING"

.750

.216

.216



Shaker Glass Profile

SG S

TIL

E P

RO

FIL

ES

S1 Shaker Glass


FOR MODELS 318

BLANK PAGE



2014

Ver

sion

7.0


FOR 313GT2 MODELS


• When machining doors on the Unique Model 313:

1. Material must be exact prior to machining on the Model 313.

2. Material Check process- Check thickness- Check width- Check finished length- Check profile* Use calipers to check the dimensions

3. The 313 machine table must be completely clean and void of any debris prior to loading material.

4. The Model 313 is a very precise machine tool and is capable of producing very accurate miter joints. To ensure perfect joints use consistantly sized material. Poor material quality will not yield a good joint.

• All Unique 313’S come standard with a complete set of tooling. Model 313GT2 comes withcounter rotating hogging tools.

1.181 [30.00mm]


DEPTH

1.250BORE



1.575 [40.00mm]

1.181 [30.00mm]

H



1.575 [40.00mm]

HOGCUTTER NUMBER

230-27155-0000



5.356

.642

.642

.551

.515

1.000

.140

.642

.371

.642

TE

CH

NIC

AL

NO

TE

S

FOR MODELS 313/313GT2


2014

Ver

sion

7.0


1.000R.031

.290

.167

.151

.156

.067

1.181 [30.00mm]


DEPTH

1.250BORE



1.575 [40.00mm]

C

FIN

GE

R J

OIN

T P

RO

FIL

ES

Finger Joint Profile

Finger Joint


FJ Cutter Body - C216-21830-0000 CW/CCW


INSERT

BACKER PLATE






2014

Ver

sion

7.0


Finger Joint Profile

FIN

GE

R J

OIN

T P

RO

FIL

ES

HOGCUTTER NUMBER

230-27155-0000



CUTTER SET NUMBER230-27155-7000

1.250

5.658

5.356

.642

.642

.551

.515

1.000

.140

.642

.371

.642

HOG1.000

.151

.502

.371

.127

THE HOG UNIT WILL LEAVE.015 STOCK FROM THE FINISHED FINGER JOINT PROFILE.

FOR 313GT2 MODELS ONLY

REPLACEMENT INSERTSI332394

QTY 9 PER TOOL

FJ PCD Tool - C290-23703-1000 CWFJ PCD Tool - C290-23704-2000 CCW



BLANK PAGE


2014

Ver

sion

7.0


MORTISE SPINDLEPART NUMBER

04232-1/2

TENON SPINDLEPART NUMBER

04232-3/4

MORTISE EXT.PART NUMBER

04216-3/8

PART NUMBER04895

MORTISE EXT

PART NUMBERC3450-MORTBIT

MORTISE BIT

NOPHOTO

PART NUMBERI810-26876-1000

QTY 2 PER TOOL

SCORING INSERTS

.500CUTTER NUMBER130-28349-1000

.031 x 45°

.500

.166 TYP.

.020 DEEPGROOVE

.020SCORE

.020SCORE

FOR MODELSWITHOUT SCORING

FOR MODELSWITH SCORING

.500CUTTER NUMBER130-28348-1000

.031 x 45°

.500

.020SCORE

.020SCORE

MO

RT

ISE

& T

EN

ON

ADDITIONAL TOOLING

HOGGING INSERTSPART NUMBER

I-TRIM-GR8QTY 16 PER TOOL

FOR MODELS 3450


2014

Ver

sion

7.0


1.299 [33.00mm]

1.181 [30.00mm]

1.299 [33.00mm]


DEPTH

1.181 [30.00mm]



1.250BORE

4.080

.620

2.500

3.000

.170

.250

U-339.500

• When machining panels on Unique Shape & Sands:

1. A support bearing is recommended when no back cutter is used.

2. When machining raised panels on machines with two shapers, a roughing cutter on the first spindle can be used to remove the majority of the material thus saving tooling life on the second spindles profile inserts.

3. If using a sizing “InSet” fence it is recommended that a trim cutter is used under the panel cutter to dimension the part. This configuration may change some depending on the number of shaper heads used on the machine.

• All Unique Shape & Sands come standard with floating heads for arched raised panel shaping and sanding.All Unique Shape & Sand machines are shipped without tooling. Customer tooling will be setup on newmachine orders if tooling is received at Unique one week prior to machine delivery date.


TE

CH

NIC

AL

NO

TE

S



2014

Ver

sion

7.0


TYPICAL SHAPE AND SAND SETUP

CW

Pan

el S

and

erC

W E

dge

San

der

TE

CH

NIC

AL

NO

TE

S

CC

W P

anel

San

der

CC

W E

dge

San

der

CC

W P

anel

Rou

gher

CC

W C

onve

nti

onal

Ed

ge C

utt

er

CC

W P

anel

Fin

ish

ing

Cu

tter

CW

CL

imb

Cu

t E

dge

Cu

tter


2014

Ver

sion

7.0


FOR SHAPE & SAND MODELS

U264 Profile


I810-09808-2400 CCW

U303 Profile



I810-09808-2700 CCW


I810-09808-2200 CCW


I810-09808-2900 CCW

.3751.750

R1.250

.375

.594

.831

.245.130

R1.250

.750 .620 U-339G

.750.245

R1.250

.130

.831

.375

R.150

1.748

U-264

R.1501.743

R.150

R.150R.150

.750 U-303

R.150R.150.375

.245.130

.831

.245.130

R1.250

.750

.831

R1.250

1.750

U-339

R.188

.375

PAN

EL

PR

OF

ILE

S Panel Profiles

NO BACK CUTTERW/ SUPPORT BEARING

.620

2.500

3.000

.170

.250

U-339

SHIM KIT NUMBER910-09808-7000

.500

990-10034-0100BEARING NUMBER

C230-10034-1000 CWC230-10034-2000 CCW


2.028

1.063 [27.00mm]

.750

.921

4.239

2.500 BEARING

.590 TABLE BED

U-339



.720

.500BEARING

1.2506.000

FACE COMING

BACK INSERTI810-09085-0030

C210-10034-1000 CWC210-10034-2000 CCW

C230-10035-1000 CWC230-10035-2000 CCW

WITH BACK CUTTER



2014

Ver

sion

7.0



PAN

EL

PR

OF

ILE

SPanel Profiles

U339S Profile U416 Profile

U429 Profile U429S Profile

.750.245

R1.500

.375

1.750

.831

.130

U-429

R.125

.130.245

R2.000

.750

R.150

.831

1.748

R.188

U-416

.375

.245

1.562

R.132 .414

R.928R.840

.351

.594

.844

U-339S.596


I810-30283-2000 CCW


I810-09808-2600 CCW


I810-09808-2100 CCW


I810-09808-2110 CCW


2.028

1.063 [27.00mm]

.750

.921

4.239

2.500 BEARING

.590 TABLE BED

U-339



.720

.500BEARING

1.2506.000

FACE COMING


C210-10034-1000 CWC210-10034-2000 CCW

C230-10035-1000 CWC230-10035-2000 CCW

WITH BACK CUTTER


.620

2.500

3.000

.170

.250

U-339


.500


C230-10034-1000 CWC230-10034-2000 CCW

.594.130

.831

.620.750.375

R1.500

1.750

.245

.375

R.125

R.055


2014

Ver

sion

7.0



.620

2.500

3.000

.170

.250

U-339


.500


C230-10034-1000 CWC230-10034-2000 CCW


PAN

EL

PR

OF

ILE

S Panel Profiles




.750.245

.130

.375

R2.500

1.695

U-460

.831

.245.130

.750

.831

1.748

U-763

R.188

.375

R.150R.150R.150

1.746

.130

.831

.750 U-479.245

.375

.245

.594

.375

1.750

.130

.375

.831

.750 .620 U-763G

.126


I810-09808-2500 CCW


I810-09808-2300 CCW


I810-09808-2000 CCW


I810-09808-2120 CCW

2.028

1.063 [27.00mm]

.750

.921

4.239

2.500 BEARING

.590 TABLE BED

U-339



.720

.500BEARING

1.2506.000

FACE COMING


C210-10034-1000 CWC210-10034-2000 CCW

C230-10035-1000 CWC230-10035-2000 CCW

WITH BACK CUTTER



2014

Ver

sion

7.0


1.250

2.500

6.000

.625

1.000

.500

990-10034-0000BEARING

SPACER NUMBER910-19287-0000

FINISHED PROFILE

CUTTER SET NUMBERC230-19287-7100CONSISTING OF:1- (3 INSERT) CUTTER NUMBER C230-19287-02001- (2 INSERT) CUTTER NUMBER C230-19287-0300

SUPPORT BEARING NUMBERC990-10034-0100 CW/CCW

2.500

3.000

.170

.250

.500

SUPPORT BEARINGRECCOMENDED WHEN

NO BACK CUTTER ISUSED WITHPANEL SET

RUB BEARING NUMBERC990-10034-0000 CW/CCW

2.500 BEARING

.500BEARING

1.250

RUB BEARING REQUIRED WHEN NOTRIM CUTTER IS USED WITH

PANEL SET

HO

GG

ER

T

OO

LS


• All Unique Shape & Sands come standard with floating heads for arched raised panel shaping and sanding.A support bearing is reccomended when no back cutter is used on thecutter stations.Sand rub bearings are required when arching.

REPLACEMENT INSERT NUMBER(15 PER CUTTER SET)

I810-09085-0030

0.5258

1.250” ID SHIM KITI810-09808-7000

Panel Profiles


2014

Ver

sion

7.0


TABLE BED


DEPTH


1.299 [33.00mm]


1.181 [30.00mm]

1.250BORE

C215-09854-2000 CCW

2 WING HEADC215-09854-1000 CW

SG E

DG

E P

RO

FIL

ES

INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE






SG Edge Detail Profiles

U0065 Profile

EDGE INSERTI816-09820-2000 CCW

U0090 Profile





Edge Cutter Body - C215-09854-2000 CCWConventional Cut



.750

.219

R.250.531

20°

20°

U-0147

45°

.156

.750 .594U-0065

.156

.750

R.125

U-0090

.750

R.625U-0114



2014

Ver

sion

7.0


SG E

DG

E P

RO

FIL

ES

INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE







U0162 Profile


U0175 Profile






TABLE BED


DEPTH


1.299 [33.00mm]


1.181 [30.00mm]

1.250BORE

C215-09854-2000 CCW

2 WING HEADC215-09854-1000 CW



.500

.250

.750 U-0162

R.250

.250

.250

.344

R.188R.094

.750 U-0175

.344

U-0198.750

R.094R.109

.470

.380

U-0207.750

R.125

.113

.438

.312

R.438


2014

Ver

sion

7.0


TABLE BED


DEPTH


1.299 [33.00mm]


1.181 [30.00mm]

1.250BORE

C215-09854-2000 CCW

2 WING HEADC215-09854-1000 CW

SG E

DG

E P

RO

FIL

ES

INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE







U0215 Profile


U0230 Profile








R.406

.750 U-0340

.281

.111

.399

.351

R.109R.250

U-0358.750

.250

.750.354

R.250

.396U-0230

.182

R.125

.750

R.118

U-0215

R.118



2014

Ver

sion

7.0


SG E

DG

E P

RO

FIL

ES

INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE







U0360 Profile


U0644 Profile






TABLE BED


DEPTH


1.299 [33.00mm]


1.181 [30.00mm]

1.250BORE

C215-09854-2000 CCW

2 WING HEADC215-09854-1000 CW



.750 U-0360

R.375

.375

40°

.625.750 .500 U-0644

.537.750

R.063

.213

.252

U-0677

R.281

.750.488

12°

.262

R.125.180

R.250

U-0860


2014

Ver

sion

7.0


.750 U-0870

.184

.531

.219

40°

.750 U-4444

R.250

TABLE BED


DEPTH


1.299 [33.00mm]


1.181 [30.00mm]

1.250BORE

C215-09854-2000 CCW

2 WING HEADC215-09854-1000 CW

SG E

DG

E P

RO

FIL

ES

INSERT

BACKER PLATE


INSERT

BACKER PLATE





U0870 Profile


U4444 Profile







2014

Ver

sion

7.0


INSERT BACKER PLATE

1.339 [34.00mm]

1.457 [37.00mm]

.394 [10.00mm]MAX. PROFILE

5.21

3 M

IN. C

UTT

ING

CIR

CLE

6.00

0 CO

NST

ANT

1.25

0BO

RE

STANDARD #1CUTTER NUMBER216-21820-1000

3 WINGSCLIMB CUTTING

PART WITH PROFILE UP

45°

.156

.750 .594U-0065

.156

.750

R.125

U-0090

.344

U-0198.750

R.094R.109

.470

CLIMB CUT VERSIONFOR STD# 1 CUTTERS

Select profiles shown. For partnumber of profile not pictured

below please contact the UniqueTooling Department


SG E

DG

E P

RO

FIL

ES

INSERT

BACKER PLATE


INSERT

BACKER PLATE


BACKER REQUIREDWITH THIS TOOLI850-18427-1000 CW


U0065 Profile

EDGE INSERTI816-18427-1000 CW

U0090 Profile


INSERT

BACKER PLATE


INSERT

BACKER PLATE




U0198 Profile


U0360 Profile

EDGE INSERTI816-17186-1000 CW.750 U-0360

R.375

.750 U-0870

.184

.531

.219

40°

.750 U-4444

R.250

INSERT

BACKER PLATE


INSERT

BACKER PLATE




U0870 Profile


U4444 Profile




2014

Ver

sion

7.0


SG E

DG

E P

RO

FIL

ES

INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE







U0099 Profile


U063 Profile





1.250BORE



1.181 [30.00mm]

TABLE BED


DEPTH

1.299 [33.00mm]

2 WC215-09C215-09




.750

R.109

.591

R.250

.328

U-0122

.188

R.063

.750

R.344

.552

.490

R.250

U-0099

.090

.750

R.188

R.438

.281

U-0108

.475

.750

R.062



2014

Ver

sion

7.0


SG E

DG

E P

RO

FIL

ES

INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE







U0154 Profile


U0190 Profile





1.250BORE



1.181 [30.00mm]

TABLE BED


DEPTH

1.299 [33.00mm]

2 WC215-09C215-09




20°

.406

.469

R.109

R.125

.750 U-0241

R.512

.750 U-0154 U-019020°

.750

.507

.500

.250

22°

R.094

R.219

.127

.538

.750 U-0220

R.094

.250

.500

R.219


2014

Ver

sion

7.0


SG E

DG

E P

RO

FIL

ES

INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE







U0255 Profile


U0284 Profile





1.250BORE



1.181 [30.00mm]

TABLE BED


DEPTH

1.299 [33.00mm]

2 WC215-09C215-09




R.203

.375

.375.750 U-284

.141 R.234

.531R.125

R.125

.453

.297

R.125.438

.750 U-0285

15°

.249

U-255.750

R.125R.156

R.313

.335

.415

.500

.433

.750 U-0885

.290

R.094

R.375

R.063



2014

Ver

sion

7.0


SG E

DG

E P

RO

FIL

ES

INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE






U313 Profile


U314 Profile

U0381 Profile



1.250BORE



1.181 [30.00mm]

TABLE BED


DEPTH

1.299 [33.00mm]

2 WC215-09C215-09




.500 R.125

.313

R.125

.438.750 U-313 U-314.750

R.125R.125.500

.437

.313

30°

.750

R.188

R.281

.344

R.125

U-381

.248

.590


2014

Ver

sion

7.0


.500 R.125

.313

R.125

.438.750 U-313

.249

U-255.750

R.125R.156

R.313

.335

.415

.500

R.125

.453

.297

R.125.438

.750 U-0285

15°

R.219

.127

.538

.750 U-0220

R.094

.250

.500

R.219

R.512

.750 U-0154.750

R.063

INSERT

BACKER PLATE




U063 Profile


U0154 Profile


INSERT

BACKER PLATE


INSERT

BACKER PLATE




U0220 Profile


U0255 Profile


INSERT

BACKER PLATE


INSERT

BACKER PLATE




U0285 Profile


U313 Profile




PART WITH PROFILE UP

INSERT BACKER PLATE

1.339 [34.00mm]

1.457 [37.00mm]


4.81

9 M

IN. C

UTT

ING

CIR

CLE

6.00

0 CO

NST

ANT

1.25

0BO

RE


CLIMB CUT VERSIONFOR STD# 2 CUTTERS

Select profiles shown. For partnumber of profile not pictured

below please contact the UniqueTooling DepartmentSG

ED

GE

PR

OF

ILE

SFOR SHAPE & SAND MODELS



2014

Ver

sion

7.0


R.030

.436

R.219.593

.299

.750 U-322

R.125R.313

.314


.750R.125

U-453.750

R.125

.438

30°

.438

.750

.312

R.125

U-454.750

R.125



1.181 [30.00mm]

TABLE BED


DEPTH

1.299 [33.00mm]

1.250BORE

2 WING HEADC215-09852-1000 CWC215-09852-2000 CCW

SG E

DG

E P

RO

FIL

ES

INSERT

BACKER PLATE


INSERT

BACKER PLATE


INSERT

BACKER PLATE





U322 Profile


U453 Profile

U454 Profile






CLIMB CUT VERSIONALSO AVAILABLE


2014

Ver

sion

7.0


PART NUMBERREPLACEMENT INSERT

811-22255-1000811-22255-1100

U-0000

1.250 BORE

1.339 [34.00mm].813

.263

.263.382

6.000


CLIMB CUTTING1.457

[37.00mm]

REPLACEMENT INSERT NUMBERI331889

3” OD HOGGER FOR 2752, 2753, 2710 & 2722C230-14545-0000

1.250 BORE

.984 [25.00mm]

3.000

U-0000

1.250 BORE

1.339 [34.00mm].813

.263

.263.382

6.000


CONVENTIONAL CUTTING

PART NUMBERREPLACEMENT INSERT

811-22254-2000811-22254-2100

HO

GG

ER

T

OO

LS Shaker Edge Tools




2014

Ver

sion

7.0


CAN ACCOMMODATE ALL PROFILES ON EDGE DETAIL PAGESPLEASE CALL FOR INFORMATION,

QUOTATION & PART NUMBER

INSERT BACKER PLATE

BACKER PLATE SCREWM3x8SHCS

CLAMPSCREWM8x15SHCS


5.21

3 M

IN. C

UTT

ING

CIR

CLE

6.00

0 CO

NST

ANT

1.25

0BO

RE

1.339 [34.00mm]

1.457 [37.00mm]


2 WINGSCONVENTIONAL CUTTING

PART WITH PROFILE DOWN




INSERT BACKER PLATE


CLAMPSCREWM8x15SHCS

1.339 [34.00mm]

1.457 [37.00mm]


4.81

9 M

IN.

CUTT

ING

CIR

CLE

6.00

0 CO

NST

ANT

1.25

0BO

RE




INSERT BACKER PLATE


CLAMPSCREWM8x15SHCS


4.81

9 M

IN. C

UTT

ING

CIR

CLE

6.00

0 CO

NST

ANT

1.25

0BO

RE

1.339 [34.00mm]

1.457 [37.00mm]




INSERT BACKER PLATE


CLAMPSCREWM8x15SHCS

1.339 [34.00mm]

1.457 [37.00mm]


4.42

5 M

IN. C

UTT

ING

CIR

CLE

6.00

0 CO

NST

ANT

1.25

0BO

RE




INSERT BACKER PLATE


CLAMPSCREWM8x15SHCS


4.42

5 M

IN. C

UTT

ING

CIR

CLE

6.00

0 CO

NST

ANT

1.25

0BO

RE

1.339 [34.00mm]

1.457 [37.00mm]

INSERT BACKER PLATE


CLAMPSCREWM8x15SHCS

1.339 [34.00mm]

1.457 [37.00mm]


5.21

3 M

IN. C

UTT

ING

CIR

CLE

6.00

0 CO

NST

ANT

1.25

0BO

RE





SG Positive Clamp ToolsCLIMB CUT VERSION

SG E

DG

E P

RO

FIL

ES


2014

Ver

sion

7.0


SG Positive Clamp ToolsCONVENTIONAL CUT VERSION


5.21

3 M

IN.

CUTT

ING

CIR

CLE

6.00

0 CO

NST

ANT

1.25

0BO

RE

INSERT BACKER PLATE

1.339 [34.00mm]

1.457 [37.00mm]


2 WINGSCONVENTIONAL CUTTINGPART WITH PROFILE UP



INSERT BACKER PLATE.591 [15.00mm]MAX. PROFILE

4.81

9 M

IN. CU

TTIN

G C

IRCL

E

6.00

0 CO

NST

ANT

1.25

0BO

RE

1.339 [34.00mm]

1.457 [37.00mm]



INSERT BACKER PLATE.787 [20.00mm]MAX. PROFILE

4.42

5 M

IN. CU

TTIN

G C

IRCL

E

6.00

0 CO

NST

ANT

1.25

0BO

RE

1.339 [34.00mm]

1.457 [37.00mm]

CAN ACCOMMODATE ALL PROFILES ON EDGE DETAIL PAGESPLEASE CALL FOR INFORMATION,

QUOTATION & PART NUMBER

SG E

DG

E P

RO

FIL

ES


2014

Ver

sion

7.0


THIS IS APPLICATION SPECIFIC TOOLINGPLEASE CONTACT THE UNIQUE TOOLING

DEPARTMENT FOR QUOTATION

EN

TR

Y D

OO

R T

OO

LS

Entry Doors


2014

Ver

sion

7.0


WHEN ORDERING ABRASIVE LOADS, SUBSTITUTE “GRIT” FOR THE ABRASIVE GRITREQUIRED I.E. AR-460-LD-150 : AR-460-LD-180

For profile numbers not listed or to order custom profilesplease contact the Unique Tooling Department

PROFILE NUMBER

PANELSU-303U-339SU-416U-429SU-460

EDGE DETAILSU-090U-190U-198U-220U-313U-314U-360U-4444

TOOL PART NUMBER

AR-303-PANELAR-339S-PANELAR-416-PANELAR-429S-PANELAR-460-PANEL

AR-090-EDGEAR-190-EDGEAR-198-EDGEAR-220-EDGEAR-313-EDGEAR-314-EDGEAR-360-EDGEAR-4444-EDGE

ABRASIVE LOAD PARTNUMBER

AR-303-LD-GRITAR-339S-LD-GRITAR-416-LD-GRITAR-429S-LD-GRITAR-460-LD-GRIT

AR-090-LD-GRITAR-190-LD-GRITAR-198-LD-GRITAR-220-LD-GRITAR-313-LD-GRITAR-314-LD-GRITAR-360-LD-GRITAR-4444-LD-GRIT

ARMINIUS PROFILE SANDING

PR

OF

ILE

SA

ND

ING

Profile Sanding

BLANK PAGE


2014

Ver

sion

7.0


Custom or other than standard arch height templates are also available.Custom templates can be designed by our Engineers.

A template set consists of 4 panel and 4 matching rail templates.

1-1/8” Rise, UNIQUE™ Standard StyleP/N 998800 3”, 4”, 5”, 6”P/N 999812 7”, 8”, 9”, 10”P/N 998900 11”, 12”, 13”, 14”

2” Rise, UNIQUE™ Standard StyleP/N 999802 3”, 4”, 5”, 6”P/N 100009 7”, 8”, 9”, 10”P/N 100010 11”, 12”, 13”, 14”

1-1/8” Rise, UNIQUE™ Standard StyleP/N 998810 4”, 5”, 6”, 7”P/N 998820 8”, 9”, 10”, 11”P/N 998830 12”, 13”, 14”, 15”P/N 998840 16”, 17”, 18”, 19”P/N 998850 20”, 21”, 22”, 23”

2” Rise, UNIQUE™ Standard StyleP/N 100017 8”, 9”, 10” , 11”P/N 100018 12”, 13”, 14”, 15”P/N 100019 16”, 17”, 18” , 19”

1-1/8” Rise, UNIQUE™ Standard StyleP/N 998860 2”, 3”, 4”, 5”P/N 998870 6”, 7”, 8”, 9”P/N 100032 10”, 11”, 12”, 13”

2” Rise, UNIQUE™ Standard StyleP/N 100020 2”, 3”, 4”, 5”P/N 100021 6”, 7”, 8”, 9”P/N 100022 10”, 11”, 12”, 13”

OVAL / EYEBROW Style Doors

COUNTRY FRENCH Style Doors

CATHEDRAL ARCH Style Doors

Size is Radius of Arch

Size is Panel Width

Size is Top of Flat Area

250

TE

MP

LA

TE

S



2014

Ver

sion

7.0


Each Model 290 template set contains the complete list of Lexan templates below for Arch or Eyebrow,1 Aluminium mounting bracket and four

nylon template fastening screws.

Cathedral Template Set - ORDER # 999313Oval / Eyebrow Template Set - ORDER # 999030

UNIQUE™ 290 Standard StyleP/N 290400 8” Wide Door / 4.5” RP/N 290401 9” Wide Door / 5.25” RP/N 290402 10” Wide Door / 6.25” RP/N 290403 11” Wide Door / 7.25” RP/N 290404 12” Wide Door / 8.25” RP/N 290405 13” Wide Door / 9.5” RP/N 290406 14” Wide Door / 11” RP/N 290407 14” Wide Door / 11” R

UNIQUE™ 290 Standard StyleP/N 290216 8” Wide Door / 4.5” RP/N 290217 9” Wide Door / 5.25” RP/N 290218 10” Wide Door / 6.25” RP/N 290219 11” Wide Door / 7.25” RP/N 290220 12” Wide Door / 8.25” RP/N 290221 13” Wide Door / 9.5” RP/N 290222 14” Wide Door / 11” RP/N 290223 15” Wide Door / 12.5” RP/N 290224 16” Wide Door / 14” RP/N 290225 17” Wide Door / 15.5” RP/N 290226 18” Wide Door / 17.25” RP/N 290227 19” Wide Door / 19.25” R

UNIQUE™ 290 Optional StylesP/N 290228 20” Wide Door / 21.25” RP/N 290229 21” Wide Door / 23.25” RP/N 290230 22” Wide Door / 25.25” RP/N 290231 23” Wide Door / 27.5” RP/N 290232 24” Wide Door / 30” R

OVAL / EYEBROW Style Doors

CATHEDRAL ARCH Style Doors

Size is Radius of Arch

Size is Panel Width

The Optional Lexan templates to the right areavailable but not included in the set.

To order please contact theUnique Tooling Department

290

TE

MP

LA

TE

S


2014

Ver

sion

7.0


1-3 day engineering time1 week for receipt of approval prints & down payment4 weeks for tool manufacturingTotal lead time up to 5-6 weeks

Custom tooling orders can be engineered either from wood samples or cad drawings.Template orders can be engineered from cad drawings

Total lead time can vary depending on number of factors.

The typical lead time for custom tooling orders to be engineered, quoted and for Unique MachineTool to be in possession of customer’s approval prints and down payment ** is highlighted below:

** 50 % down payment is required on all custom orders. Balance to be paid prior to tooling being shipped.

*** Estimates may vary +/- 25%

CU

STO

M T

OO

LIN

G Custom Tooling



2014

Ver

sion

7.0


FOR USE ONLY IF YOU CAN PROVIDE PROPER PARTNUMBER AND ARE AN EXISTING CUSTOMER WHO HAS

ORDERED FROM UNIQUE DIRECT BEFORE(PART NUMBER IS LASER ETCHED ON INSERT)

FAX ORDER TO 1-602-470-1916 - YOU WILL RECEIVE ANSALES CONFIRMATION WHICH NEEDS TO BE SIGNED

AND FAXED BACK TO CONFIRM ORDER.

ITEM # QTY INSERT NUMBER PROFILE / DESCRIPTION

EX. 24 I810-09808-2500 U-460 PANEL PROFILE CCW

1

2

3

4

5

6

7

8

9

COMPANY NAME:

CONTACT NAME:

PHONE:

FAX:

CUSTOMER INFO

METHOD OF SHIPPING:(PLEASE CIRCLE)

METHOD OF PAYMENT:(PLEASE CIRCLE)

UPS GND/UPS BLUEUPS ORG/UPS RED

VISA/MC COD

PAYMENT / SHIP INFO

SHIP TO:

RE

-OR

DE

R F

OR

M

4232 E. Magnolia St.Phoenix, Arizona 85034 U.S.A.

Website: www.uniquemachine.comEmail: [email protected]

Phone: (602)470-1911Fax: (602)470-1916

UNIQUE MACHINE & TOOL OFFERSA COMPLETE

TOOLING SOLUTION

CALL 602-470-1911FOR ALL

YOUR TOOLING NEEDS

2014 TOOLING REFERENCE GUIDE VERSION 7 - … 2014v7.pdf · Page 5 4232 E. Magnolia St., Phoenix,...

Documents

Transcript of 2014 TOOLING REFERENCE GUIDE VERSION 7 - … 2014v7.pdf · Page 5 4232 E. Magnolia St., Phoenix,...