2009 Honda TRX680FA/FGA FOURTRAX RINCON/with GPScape … · FOURTRAX RINCON/with GPScape OWNER’S...

2009Honda TRX680FA/FGAFOURTRAX RINCON/with GPScapeOWNER’S MANUAL

FOR OFF-ROAD USE ONLYThis vehicle is designed and manufactured for off-road use only.

USA only:It conforms to US EPA Noise Emission regulations, but does notconform to Federal Motor Vehicle Safety Standards or US EPA OnHighway Exhaust Emission regulations, and operation on public streets,roads, or highways is illegal. The vehicle is equipped with a USDAqualified spark arrester. Obey local laws and regulations.

It conforms to US EPA, California, and Environment Canada emissionregulations for ATVs.

０８／０３／０５　１１：１６：１９　３１ＨＮ８６６０　０００２　

－

Introduction

Introduction

Congratulations on choosing your Honda ATV.

When you own a Honda, you’re part of a worldwide family of satisfiedcustomers people who appreciate Honda’s reputation for buildingquality into every product.

Your Honda was designed as a recreational ATV for off-road use byone rider only.

Before riding, take time to get acquainted with your ATV and how itworks. To protect your investment, we urge you to take responsibilityfor keeping your ATV well maintained. Scheduled service is a must, ofcourse. But it’s just as important to observe the break-in guidelines, andperform all pre-ride and other periodic checks detailed in this manual.

We also recommend that you read this owner’s manual before you ride.It’s full of facts, instructions, safety information, and helpful tips. Tomake it easy to use, the manual contains a detailed list of topics at thebeginning of each section, and both an in-depth table of contents and anindex at the back of the book.

As you read this manual, you will find information that is preceded by asymbol. This information is intended to help you avoid damage

to your Honda, other property, or the environment.

Read the Warranties Booklet (page ) thoroughly so you understandthe coverages that protect your new Honda and are aware of your rightsand responsibilities.

Whenever you ride, tread lightly. By staying on established trails andriding only in approved areas, you help protect the environment andkeep off-road riding areas open for the future.

251

０８／０３／０５　１１：１６：２６　３１ＨＮ８６６０　０００３　

Introduction

Introduction

WARNING:California Proposition 65 Warning

This product contains or emits chemicals known to theState of California to cause cancer and birth defects or otherreproductive harm.

If you have any questions, or if you ever need special service or repairs,remember that your Honda dealer knows your ATV best and isdedicated to your complete satisfaction.

You may also want to visit our website at www.honda.com.

Please report any change of address or ownership to your Honda dealerso we will be able to contact you concerning important productinformation.

Happy riding!

０８／０３／０５　１１：１６：３２　３１ＨＮ８６６０　０００４　

A Few Words About Safety

Safety Labels

Safety MessagesDANGER, WARNING, CAUTION


–– on the ATV.

–– preceded by a safety alert symbol and one ofthree signal words: or .

Your safety, and the safety of others, is very important. And operatingthis ATV safely is an important responsibility.

To help you make informed decisions about safety, we have providedoperating procedures and other information on labels and in this manual.This information alerts you to potential hazards that could hurt you orothers.

Of course, it is not practical or possible to warn you about all hazardsassociated with operating or maintaining an ATV. You must use yourown good judgment.

You will find important safety information in a variety of forms,including:

０８／０３／０５　１１：１６：３６　３１ＨＮ８６６０　０００５　

You WILL be KILLED orSERIOUSLY HURT if you don’tfollow instructions.

You CAN be KILLED or SERIOUSLYHURT if you don’t followinstructions.

You CAN be HURT if you don’tfollow instructions.



Safety Headings

Safety Section

Instructions

These signal words mean:

–– such as Important Safety Reminders or ImportantSafety Precautions.

–– such as ATV Safety.

–– how to use this ATV correctly and safely.

This entire manual is filled with important safety information –– pleaseread it carefully.

０８／０３／０５　１１：１６：４２　３１ＨＮ８６６０　０００６　

Contents

Contents

.......................................................................................ATV Safety .

...................................................................Instruments & Controls .

....................................................................................Before Riding .

...............................................................Basic Operation & Riding .

............................................GPScape System (TRX680FGA only) .

1

9

45

73

89

These pages give an overview of the contents of your owner’s manual.The first page of each section lists the topics covered in that section.

Important safety information you should know, plus a look at thesafety-related labels on your ATV.

The location and function of indicators and controls on your ATVand operating instructions for various controls and features.

Instructions for use of your ATV Navigation System.

The importance of wearing a helmet and other protective gear,how to make sure you and your ATV are ready to ride, andimportant information about loading.

How to start and stop the engine, shift gears, and brake. Also,riding precautions.

０８／０３／０５　１１：１６：５１　３１ＨＮ８６６０　０００７　

Contents

Contents

.....................................................................Servicing Your Honda .

....................................................................................................Tips .

......................................................Taking Care of the Unexpected .

.....................................................................Technical Information .

....................................................................Consumer Information .

.............................................................................Table of Contents .

..................................................................................................Index .

Quick Reference

125

201

211

233

247

256

264

Why your ATV needs regular maintenance, what you need to knowbefore servicing your Honda, an owner maintenance schedule, andinstructions for specific maintenance and adjustment items.

How to store and transport your ATV and how to be anenvironmentally responsible rider.

What to do if you have a flat tire, your engine won’t start, etc.

ID numbers, technical specifications, and other technical facts.

Information on warranties, emission controls, how to get Hondaservice manuals.

Sequential listing of topics in this owner’s manual.

Handy facts about fuel, engine oil, tire sizes, and air pressures.

０８／０３／０５　１１：１７：０３　３１ＨＮ８６６０　０００８　

０８／０３／０５　１１：１７：０５　３１ＨＮ８６６０　０００９　

1

ATV Safety

ATV Safety

This section presents some of the most important information andrecommendations to help you ride your ATV safely. Please take a fewmoments to read these pages. This section also includes informationabout the location of safety labels on your ATV.

.........................................................................................Safety Labels ................................................................Important Safety Information . 2

5

０８／０３／０５　１１：１７：０９　３１ＨＮ８６６０　００１０　

2

Important Safety Information

Follow the Age Recommendation

Never Carry a Passenger

Always Wear a Helmet

ATV Safety

Your ATV can provide many years of service and pleasure if you takeresponsibility for your own safety and understand the challenges youcan meet while riding.

There is much that you can do to protect yourself when you ride. You’llfind many helpful recommendations throughout this manual. Thefollowing are a few that we consider to be most important.

The minimum recommended age for this ATV model is 16. Childrenunder age 16 should never operate this vehicle. Refer to the agewarnings provided in this manual and on the ATV.

Your ATV is designed for one person only. There are no handholds,footrests, or seat for a second person, so never carry a passenger. Apassenger could interfere with your ability to move around to maintainyour balance and control of the ATV.

It’s a proven fact: helmets significantly reduce the number and severityof head injuries. So always wear an approved motorcycle helmet. Wealso recommend that you wear eye protection, sturdy boots, gloves, andother protective gear (page ).74

０８／０３／０５　１１：１７：１７　３１ＨＮ８６６０　００１１　

3


ATV Safety

Ride Off-road Only

Take Time to Learn & Practice

Be Alert for Off-road Hazards

Your ATV is designed and manufactured for off-road use only. Thetires are not made for pavement, and the ATV does not have turn signalsand other features required for use on public roads. If you need to crossa paved or public road, get off and walk your ATV across.

The terrain can present a variety of challenges when you ride off-road.Continually ‘‘read’’ the terrain for unexpected turns, drop-offs, rocks,ruts, and other hazards. Always keep your speed low enough to allowtime to see and react to hazards.

Even if you have ridden other ATVs, take time to become familiar withhow this ATV works and handles. Practice in a safe area until you buildyour skills and get accustomed to the ATV’s size and weight.

Because many accidents involve inexperienced or untrained riders, weurge all riders to take a training course approved by the ATV SafetyInstitute (ASI). See page .Contact an authorized ATV dealer or call 1-800-887-2887 (USA only)to find out about the training courses nearest you.

76

０８／０３／０５　１１：１７：２３　３１ＨＮ８６６０　００１２　

4


ATV Safety

Ride within Your Limits

Keep Your Honda in Safe Condition

Don’t Drink and Ride

Pushing limits is another major cause of ATV accidents. Never ridebeyond your personal abilities or faster than conditions warrant.Remember that alcohol, drugs, fatigue, and inattention can significantlyreduce your ability to make good judgments and ride safely.

Alcohol and riding don’t mix. Even one drink can reduce your ability torespond to changing conditions, and your reaction time gets worse withevery additional drink. So don’t drink and ride, and don’t let yourfriends drink and ride either.

It’s important to keep your ATV properly maintained and in safe ridingcondition. Having a breakdown can be difficult, especially if you arestranded off-road far from your base. To help avoid problems, inspectyour ATV before every ride and perform all recommended maintenance.

０８／０３／０５　１１：１７：２９　３１ＨＮ８６６０　００１３　

5ATV Safety

Safety Labels

The labels should be considered permanent parts of the vehicle. If alabel comes off or becomes hard to read, contact your Honda dealer forreplacements.

Your ATV comes with a hang tag and several labels containingimportant safety information. Anyone who rides the vehicle should readand understand this information before riding.

０８／０３／０５　１１：１７：３３　３１ＨＮ８６６０　００１４　

6

Safety Labels

ATV Safety

０８／０３／０５　１１：１７：４３　３１ＨＮ８６６０　００１５　

7

Safety Labels

ATV Safety

０８／０３／０５　１１：１７：５２　３１ＨＮ８６６０　００１６　

(For Canada)

8

Safety Labels

ATV Safety

０８／０３／０５　１１：１８：０６　３１ＨＮ８６６０　００１７　

9

Instruments & Controls


This section shows the location of all indicators and controls you wouldnormally use before or while riding your ATV.

The items listed on this page are described in this section. Instructionsfor other components are presented in other sections of this manualwhere they will be most useful.

(cont’d)

............................................................................Indicators & Displays .......................................................................Multi-function Display .

........................................................................Drive Mode Indicator .......................................................................Gear Position Indicator .

.........................................................................Oil Change Indicator ............................................................................................Odometer ............................................................................................Tripmeter .

........................................................................................Fuel Gauge .

.........................................................................................Hourmeter ......................................................................................Digital Clock .

..........................................................Operation Component Locations .1114192021222323252629

０８／０３／０５　１１：１８：１６　３１ＨＮ８６６０　００１８　

10



..............................................................................Controls & Features ...................................................................................Ignition Switch .

........................................................................................Shift Lever ..................................................................Drive Mode Select Switch ..................................................................2WD/4WD Select Switch .

.......................................................................................Start Button ............................................................................Engine Stop Switch .

...............................................................................Headlight Switch ..................................................................Headlight Dimmer Switch .

.....................................................................................Recoil Starter ....................................................................................Throttle Lever .

................................................................................Gearshift Switch ..............................................................................Front Brake Lever .

..............................................................................Rear Brake Lever ................................................................................Rear Brake Pedal .

....................................................................................Parking Brake ...............................................................................Flag Pole Bracket ...............................................................................Accessory Socket .

303031323334343535363738393939404142

０８／０３／０５　１１：１８：２９　３１ＨＮ８６６０　００１９　

throttle lever

ignition switch

engine stopswitch

start button

gearshiftswitches

drive modeselect switch

front brakelever

shift lever

headlight switch

headlight dimmer switch

rear brake lever/parking brake lever

2WD/4WDselect switch

parking brakelock lever

11Instruments & Controls

Operation Component Locations

０８／０３／０５　１１：１８：３４　３１ＨＮ８６６０　００２０　

rear cargo rack

front cargo rack

accessorysocket

recoil starter

rear brake pedal

12 Instruments & Controls


０８／０３／０５　１１：１８：３８　３１ＨＮ８６６０　００２１　

flag pole bracketseat latch

13Instruments & Controls


０８／０３／０５　１１：１８：４２　３１ＨＮ８６６０　００２２　

(1)(9)

(11)(6)

(9)(8)

(7)

(3)

(6)(5)(4) (5)

TRX680FGATRX680FA

(11)

(3)

(1)

(3) reverse indicator(4) 4WD indicator(5) high oil/coolant temperature indicator

(10)(4)

(2)

(7) (8) (10)

(2)

(1) odometer/tripmeter select button(2) RESET button (TRX680FA)

hourmeter/digital clock select button (TRX680FGA)

(6) neutral indicator(7) multi-function display(8) hour select button (TRX680FA)

plus button (TRX680FGA)(9) minute select button (TRX680FA)

minus button (TRX680FGA)(10) ADJ button (TRX680FA)

GPS/WP button (TRX680FGA)(11) PGM-FI indicator

14

Indicators & Displays


The indicators and displays on your ATV keep you informed, alert youto possible problems, and make your riding safer and more enjoyable.Refer to the indicators frequently. Their functions are described on thefollowing pages.

USA: Displays read in mph and miles.Canada: Displays read in km/h and kilometers.

０８／０３／０５　１１：１８：５０　３１ＨＮ８６６０　００２３　

(1)

(1) multi-function display

(1)TRX680FA TRX680FGA

15



LampCheck.

Display Check.

Lamp CheckThe high oil/coolant temperature indicator, 4WD indicator, neutralindicator, reverse indicator and PGM-FI indicator comes on for a fewseconds and then go off when you turn the ignition switch ON ( ).This indicator is identified in the table on page with the words:

When applicable, the reverse or neutral indicators come on when youturn the ignition switch ON ( ) and remain on until you shift out ofreverse or neutral.

If one of these indicators does not come on when it should, have yourHonda dealer check for problems.

Display Check

The displays are identified in the table on page with the words:

If any part of these displays does not come on when it should, have yourHonda dealer check for problems.

When the ignition switch is turned ON ( ), the multi-function display( ) will temporarily show all the modes and digital segments so you canmake sure the liquid crystal display is functioning properly.1

16

16

０８／０３／０５　１１：１９：０１　３１ＨＮ８６６０　００２４　

16



Lamp Check.

Lamp check.

Lamp check.

Odometer/tripmeterselect button

RESET button

Selects display of the hourmeter ordigital clock (pages , ).

Selects display of the odometer ortripmeter A or tripmeter B (page ).This button also used to reset the oilchange indicator (page ).Selects display of the odometer ortripmeter. Resets the tripmeter to zero(0) (page ).This button also used to reset the oilchange indicator (page ).

Odometer/tripmeterselect button

Resets the tripmeter to zero (0)(page ).This button also used to reset the oilchange indicator (page ).

This button also used to reset the oilchange indicator (page ).

Hourmeter/digitalclock select button

Lights when engine oil and/orcoolant temperature is high enoughto adversely affect the service life ofthe engine.If the high oil/coolant temperatureindicator comes on while you areriding, immediately bring the vehicleto a stop, turn the engine off and letit cool. See page .

High oil/coolanttemperatureindicator

4WD indicator

Reverse indicator

Lights when the drive mode is in the4WD mode. The 4WD indicatorblinks if there is a possible problemwith the 2WD/4WD select system.See your Honda dealer as soon aspossible.

Lights when the transmission is inreverse.

1

2

3

4

5

(TRX680FGA) 23

24

22

22

22

25 27(TRX680FGA)

22

223

23

０８／０３／０５　１６：０１：４６　３１ＨＮ８６６０　００２５　

17



Display Check.

Lamp Check

Shows the time (hours and minutes)(page ).

Shows hours and tenths of hours ofengine operation (page ).

Shows mileage per trip (page ).

Shows accumulated mileage(page ).

Lights when specified maintenanceinterval for engine oil change isreached (page ).

Shows approximate fuel supplyavailable (page ).

Shows the gear position (page ).

Shows the driving mode(page ).

The display includes the followingfunctions.

Digital clock

HourmeterTripmeter

Odometer

Gear positionindicatorSpeedometer

Drive modeindicator

Multi-functiondisplay

Fuel gaugeShows riding speed.

Oil changeindicator

6

7

Neutral indicator Lights when the transmission is inneutral. .

23

2021

29

22

23

25

26

０８／０３／０５　１１：１９：２９　３１ＨＮ８６６０　００２６　

18



Lamp Check.

Hour select button

Lights when there is any abnormalityin the PGM-FI (Programmed FuelInjection) system. Should also lightfor a few seconds and then go offwhen the ignition switch is turnedON and use the start button. If theindicator comes on at any other time,reduce speed and take your vehicle toa Honda dealer as soon as possible.

This button is used to select the GPSnavigation mode and input awaypoint or to erase waypoint data.

Used to set the digital clock(page ).

Advances the latitude andlongitude when in the GPS mode.This button also used to set thedigital clock (page ).

PGM-FI indicator

GPS/WP button

ADJ button

Minus button

Minute select button

Plus button Advances the latitude and longitudewhen in the GPS mode.This button also used to set thedigital clock (page ).

8

9

10

11

Advances the hour displayed by thedigital clock (page ).

Advances the minutes displayed bythe digital clock (page ).

(TRX680 FGA)

(TRX680 FGA)

(TRX680 FGA)

27

27

26

26

26

０８／０３／０５　１６：０１：５７　３１ＨＮ８６６０　００２７　

(3)

(4) (9) (6) (12) (16) (17)

(15)

(4)

(5)

(2)

(6) (7) (8) (10)

(1) (13) (14)(11) (12) (3) (1)(7) (19) (14)(18)

(5)

TRX680FA TRX680FGA

(1) multi-function display(2) RESET button (TRX680FA)(3) odometer/tripmeter select button(4) gear position indicator(5) drive mode indicator(6) speedometer(7) fuel gauge(8) hour select button (TRX680FA)

(12) odometer/tripmeter(13) digital clock (TRX680FA)(14) oil change indicator

(9) minute select button (TRX680FA)(10) ADJ button (TRX680FA)(11) hourmeter (TRX680FA)

(17) plus button (TRX680FGA)(18) minus button (TRX680FGA)(19) digital clock/hourmeter

(TRX680FGA)

(15) digital clock/hourmeterselect button (TRX680FGA)

(16) GPS/WP button(TRX680FGA)

19

Multi-function Display



The multi-function display ( ) includes the following functions:

The digital clock and tripmeter will reset if the battery is disconnected.

1SpeedometerOdometerTripmeter

Drive mode indicatorGear position indicatorOil change indicator

Digital clockHourmeterFuel gauge

０８／０３／０５　１１：１９：５１　３１ＨＮ８６６０　００２８　

(1)

(1) drive mode indicator

(1)

TRX680FA TRX680FGA

20

Drive Mode Indicator



The drive mode indicator ( ) shows the selected drive mode when theignition switch is in the ON ( ) position.

The drive mode indicator ( ) displays ESP when the manual shift (ESP)mode is selected. The ESP display vanishes when the automatic shift(AUTO) mode is selected.

1

1

０８／０３／０５　１１：１９：５７　３１ＨＮ８６６０　００２９　

－

(1)

(1) gear position indicator


21

Gear Position Indicator



The gear position indicator ( ) shows the gear position when theignition switch is in the ON ( ) position.

‘‘- -’’ will be displayed on the gear position indicator when thetransmission is not shifted into gear properly. Before riding, check thatthe gear position is properly displayed on the gear position indicator.

The indicator displays: N for neutral, R for reverse, D for drive, and 13 for the three forward speed positions in the ESP mode.

1

０８／０３／０５　１１：２０：０４　３１ＨＮ８６６０　００３０　

(1) oil change indicator(2) odometer/tripmeter

select button

(2) (1)

(3) RESET button(4) digital clock/hourmeter

select button


(3)

(2)

(1)

(For TRX680FGA)

(For TRX680FA)

22

Oil Change Indicator



The oil change indicator ( ) appears in the display when the mileage oroperating hours on your ATV approaches the oil change intervalspecified on the maintenance schedule.

If the oil is changed before the oil change indicator appears, be sure toreset the oil change indicator after changing the oil. The indicator willappears for 2 seconds, then disappear. This means the indicator is reset.

Reset the indicator after each oil change.

To reset the indicator, press and hold both the odometer/tripmeter selectbutton ( ) and RESET button ( ) for more than 2 seconds. Theindicator will disappear.

To reset the indicator, press and hold both the odometer/tripmeter selectbutton ( ) and digital clock/hourmeter select button ( ) for more than 2seconds. The indicator will disappear.

1

32

2 4

０８／０３／０５　１１：２０：１２　３１ＨＮ８６６０　００３１　

(1) odometer

(2) (1)

(2) odometer/tripmeter select button

(3)

(1)

(2) odometer/tripmeter select button(3) tripmeter

(2)

TRX680FA TRX680FGA

(For TRX680FGA)

23

Odometer

Tripmeter



When selected, the odometer ( ) registers total distance traveled inmiles while the ignition is ON ( ). To change the display from tripmeterto odometer, press and release the odometer/tripmeter select button ( ).

When selected, the tripmeter ( ) shows mileage per trip while theignition is ON ( ). To change the display from odometer to tripmeter,press and release the odometer/tripmeter select button ( ). To reset thetripmeter to zero, press the odometer/tripmeter select button and hold itin for at least 2 seconds.

(cont’d)

1

2

3

2

０８／０３／０５　１１：２０：２２　３１ＨＮ８６６０　００３２　

(4) tripmeter A(5) tripmeter B

(6) RESET button

(4)

(6)

(2)

(5)

(2)(2)

(For TRX680FA)

24



To reset the tripmeter to zero, press and hold the RESET button ( ) formore than 2 seconds with the display in the tripmeter A or tripmeter Bmode.

The tripmeter has two sub modes, A ( ) and B ( ).To change the display from tripmeter A or tripmeter B to odometer,press and release the odometer/tripmeter select button ( ).

6

54

2

０８／０３／０５　１１：２０：２９　３１ＨＮ８６６０　００３３　

(3) hourmeter mark

(1)

(3)

(1) hourmeter

(2)

(2) hourmeter/digital clockselect button

TRX680FA TRX680FGA

(For TRX680FGA)

25

Hourmeter



To change the display from the digital clock to the hourmeter, press andrelease the digital clock/hourmeter select button ( ). The hourmetermark ( ) will appear.

The hourmeter ( ) shows accumulated hours while the ignition is ON( ). The hourmeter provides accurate service period information forinitial and regular maintenance.

1

23

０８／０３／０５　１１：２０：３７　３１ＨＮ８６６０　００３４　

(1)

(3)(2)

(3) minute select button(1) ADJ button(2) hour select button

(For TRX680FA)

26

Digital Clock



Turn the ignition switch ON ( ).

To advance the hour display one unit at a time, press and release thehour select button ( ).To advance the hour display automatically, press and hold the hourselect button. After 2 seconds, the hour display will begin advancing.Release the button when the display reaches the desired hour.To advance the minute display one unit at a time, press and release theminute select button ( ).To advance the minute display automatically, press and hold theminute select button. After 2 seconds, the minute display will beginadvancing. Release the button when the display reaches the desiredminute.To zero the minute display, press and hold both the hour and minuteselect buttons simultaneously for 2 seconds.

To adjust the time, proceed as follows.Shows hour and minute while the ignition is ON ( ).

Press the ADJ button when the display reaches the desired minute.The display will stop flashing.

To select the adjust mode, push the ADJ button ( ) once.1.2.3.

4.

5.

3

1

2

０８／０３／０５　１１：２０：４７　３１ＨＮ８６６０　００３５　

(1)

(3)

(2)

(3) minus button(1) hourmeter/digital clockselect button

(2) plus button

(For TRX680FGA)

27



(cont’d)

Turn the ignition switch ON ( ).To change the display from hourmeter to digital clock, press andrelease the digital clock/hourmeter select button ( ).

Press and hold the digital clock/hourmeter select button for more than2 seconds. The clock will be set in the adjust mode with the hourdisplay flashing.To advance the hour display one unit at a time, press and release theplus button ( ) or minus button ( ).To advance the hour display automatically, press and hold the plusbutton or minus button. After 2 seconds, the hour display will beginadvancing. Release the button when the display reaches the desiredhour.

1.

2.

3.

1

2 3

０８／０３／０５　１１：２０：５５　３１ＨＮ８６６０　００３６　

28



Press the digital clock/hourmeter select button when the displayreaches the desired hour appears. The minutes display will be flashing.

To advance the minute display one unit at a time, press and release theplus button or minus button.To advance the minute display automatically, press and hold the plusbutton or minus button. After 2 seconds, the minute display will beginadvancing. Release the button when the display reaches the desiredminute.Press the digital clock/hourmeter select button when the displayreaches the desired minutes appears. The display will stop flashing.

Your ATV’s digital clock has an automatic adjustment functionwhenever the GPS mode is selected and the system’s satellite statusis 3D Navigation (page ).72

4.

5.

6.

０８／０３／０５　１１：２１：０２　３１ＨＮ８６６０　００３７　

4.44 US gal (16.8 )

1.40 US gal (5.3 )

(2)(1)

(1) fuel gauge

(1)(2)

TRX680FA

TRX680FGA

TRX680FA TRX680FGA

(2) segment E(3) low fuel indicator

(3)

(3)

29

Fuel Gauge



The fuel gauge liquid crystal display ( ) shows the approximate fuelsupply available. The fuel tank capacity is:

All segments will flash, when the fuel gauge function is fails. See yourHonda dealer.

When segment E ( ) and low fuel indicator ( ) flash, you should refillthe tank as soon as possible. The amount of fuel remaining when theflashing starts is approximately:

1

2 3

０８／０３／０５　１１：２１：１２　３１ＨＮ８６６０　００３８　

OFF ( )ON ( )

No electrical circuits function.Electrical circuits on.

CENTER OF HANDLEBAR

(1) ignition switch

(1)

ONOFF

ONOFF

Key Position Function

30

Ignition Switch

Controls & Features


The ignition switch ( ) is used for starting and stopping the engine(page ). Insert the key and turn it to the right for the ON ( )position.

961

０８／０３／０５　１１：２１：２１　３１ＨＮ８６６０　００３９　

(1)

(1) shift lever

LEFT SIDE OF HANDLE COVER

31

Shift Lever

Controls & Features


Shif ting Gears Riding in Reverse

The shift lever ( ) has three positions: drive (D), neutral (N), andreverse (R).See (page ) and (page ).102 108

1

０８／０３／０５　１１：２１：２６　３１ＨＮ８６６０　００４０　

(1)

(1) drive mode select switch

RIGHT HANDLEBAR

32

Drive Mode Select Switch

Controls & Features


Shif ting GearsThe drive mode select switch ( ) has two positions, AUTO and ESP.See page .

1102

０８／０３／０５　１１：２１：３１　３１ＨＮ８６６０　００４１　

(1)

(1) 2WD/4WD select switch

(2)

(2) 4WD indicator

2WD MODE

4WD MODE

33

2WD/4WD Select Switch

Controls & Features


To check your present drive mode, look at the 4WD indicator ( ).

2WD mode: the 4WD indicator goes off.4WD mode: the 4WD indicator goes on.

4WD can only be engaged while the engine is running.It remains engaged until the 2WD mode is selected or the engine isstopped.Upon starting, your ATV will be in the 2WD mode, regardless of the2WD/4WD select switch position.

Your ATV is equipped with a 2WD/4WD select switch ( ), whichpermits a choice between the ‘‘2WD’’ and ‘‘4WD’’ drive modes. Selecta drive mode that’s suitable for your riding.

The 2WD/4WD select switch is located above the throttle lever. Toselect the drive mode, slide the 2WD/4WD select switch to the desiredposition.

1

2

０８／０３／０５　１１：２１：３８　３１ＨＮ８６６０　００４２　

LEFT HANDLEBAR

(1) start button(2) engine stop switch

(1)(2)

STARTRUNOFF

34

Start Button

Engine Stop Switch

Controls & Features


Starting Procedure,The start button ( ) is used for starting the engine. Pushing the button instarts the engine. See page .

The engine stop switch ( ) is used to stop the engine in an emergency.To operate, slide the switch to the OFF ( ) position. The switch mustbe in the RUN ( ) position to start the engine, and it should normallyremain in the RUN ( ) position even when the engine is OFF.

When the start button is pushed, the starter motor will crank the engine.The starter motor will not operate if the engine stop switch is in the OFF( ) position when the start button is pushed.

If your ATV is stopped with the ignition switch ON ( ) and theengine stop switch OFF ( ), the battery will discharge. Turn theignition switch OFF ( ) to prevent battery discharge.

197

2

０８／０３／０５　１１：２１：４６　３１ＨＮ８６６０　００４３　

(1)

(2)

ONOFF

LEFT HANDLEBAR

(1) headlight switch

(2) headlight dimmer switch HILO

35

Headlight Switch

Headlight Dimmer Switch

Controls & Features


The headlight switch ( ) is used to turn the headlight ON ( ) or OFF( ). To operate, turn the switch to ON ( ) or OFF ( ).

The headlight dimmer switch ( ) is used to change between the highand low beams of the headlight. To operate, turn the switch to HI ( )for high beam, LO ( ) for low beam.

2

1

０８／０３／０５　１１：２１：５２　３１ＨＮ８６６０　００４４　

RIGHT SIDE

(1)

(1) recoil starter

36

Recoil Starter

Controls & Features


Using the Recoil Starter,The recoil starter ( ) is used to start the engine when the battery is low.See page .

1101

０８／０３／０５　１１：２１：５７　３１ＨＮ８６６０　００４５　

(A)

RIGHT HANDLEBAR

(1) throttle lever(A) to open the throttle

(1)

37

Throttle Lever

Controls & Features


The throttle controls engine rpm (speed). To increase engine rpm, pressthe throttle lever ( ) with your thumb. To reduce engine rpm, releasepressure on the throttle lever. The throttle will automatically return to theclosed position (engine idle) when you remove your thumb.

1

０８／０３／０５　１１：２２：０２　３１ＨＮ８６６０　００４６　

(1)

(2)

(1) upshift switch (2) downshift switch

LEFT HANDLEBAR

38

Gearshift Switch

Controls & Features


Shif ting Gears,

Two gearshift switches are used in the ESP (manual shift) mode.These switches are used to select the next higher or lower gear in thetransmission. To operate, press the upshift switch ( ) to engage the nexthigher gear or press the downshift switch ( ) to engage the next lowergear. See page .102

21

０８／０３／０５　１１：２２：０７　３１ＨＮ８６６０　００４７　

39

Front Brake Lever

Rear Brake Lever

Rear Brake Pedal

Controls & Features


The front brake lever is used to slow or stop your ATV. To operate, pullthe lever. For information on braking techniques, see page .

The rear brake lever/parking brake lever is used to slow or stop yourATV. To operate, pull the lever. For information on braking techniques,see page .

The rear brake pedal is used to slow or stop your ATV. To operate,depress the pedal. For information on braking techniques, see page .

110

110

110

０８／０３／０５　１１：２２：１４　３１ＨＮ８６６０　００４８　

(A)

(1)(2)

(A) to lock(1) lock lever(2) rear brake lever/parking brake lever

LEFT HANDLEBAR

40

Parking Brake

Controls & Features


Parking

The brakelights are activated by applying the parking brake. When usingthe parking brake, be sure to turn the ignition switch OFF ( ) to avoiddischarging the battery.

The lock lever ( ) on the rear brake lever/parking brake lever ( )allows it to be used as a parking brake. To operate, first squeeze the rearbrake lever/parking brake lever using your left hand and then lock itwith the lock lever using your right hand. See page .

1 2

124

０８／０３／０５　１１：２２：２０　３１ＨＮ８６６０　００４９　

(1)

(1) flag pole bracket

RIGHT REAR

41

Flag Pole Bracket

Controls & Features


Flag poles are optional equipment available from your Honda dealer. Tomount a pole in the bracket ( ), follow the instructions that come withthe flag pole kit.

Flag poles are required in some riding areas. Check local regulationsbefore riding.

1

０８／０３／０５　１１：２２：２５　３１ＨＮ８６６０　００５０　

(1)

(2)

(3)

(3) cap(1) accessory socket(2) meter cover

RIGHT FRONT

42

Accessory Socket

Controls & Features


Do not plug in any heat-generating accessory, such as an automobilecigarette lighter, because it can damage the socket.

The accessory socket ( ) is attached to the right side of the meter cover( ). You can use the accessory socket to power a trouble light, spotlight,CB radio, or cell phone, etc.

To use the accessory socket, turn the ignition switch ON ( ), start theengine. Then turn the headlights OFF ( ), and open the accessorysocket cap ( ).

12

3

０８／０３／０５　１１：２２：３１　３１ＨＮ８６６０　００５１　

43

Controls & Features


If a Fuse Blows,

Be sure the engine is on and the headlights are turned off before usingthe accessory socket, otherwise you may drain the battery.

The accessory socket’s rated capacity is DC 12V, 120 Watts (10A) orless. If you exceed this limit, you may blow a fuse. Seepage .

When you are done using an accessory, unplug it, and cover the socketwith the cap.

Be careful not to flood this accessory socket when washing your ATV.

225

０８／０３／０５　１１：２２：３６　３１ＨＮ８６６０　００５２　

44 Instruments & Controls

０８／０３／０５　１１：２２：３９　３１ＨＮ８６６０　００５３　

45GPScape System

GPScape System (TRX680FGA only)

This section explains the GPScape navigation system. Instructions forthe topics listed on this page are included.

...........................................................................................Introduction ................................................................Important Safety Information .

................................................................................System Limitations ......................................................................................System Start-up .

.......................................................................................Position Fix ...........................................System Failure to Display a Position Fix .

.......................................................................................Satellite Status ..............................................................................................GPS Mode .

............................................................................GPS Mode Display ................................................................Waypoint Number Display .

.........................................................Direction to Waypoint Display .........................................................................Distance to Waypoint .

.................................................................Basic Waypoint Selection ...........................................................Advanced Waypoint Selection .

....................Determining the Coordinates of Your Current Position ..................................................................Compass Direction Indicator .................................................................Automatic Clock Adjustment .

4649505151525456585960626365697072

０８／０３／０５　１１：２２：５１　３１ＨＮ８６６０　００５４　

°

°

°

°

LATITUDE

90 N (North Pole)

0 latitude(equator)

NorthernHemisphere

SouthernHemisphere 90 S (South Pole)

(degree)Each degree contains 60’ (minutes)

(seconds)Each minute contains 60’’

Each circle contains 360

46

Introduction

GPScape System

Any location on Earth may be described by two positioning coordinates.These two coordinates, measured by degrees, minutes, and seconds, are:

latitudelongitude

Latitudes are horizontal circles drawn around the Earth. The zero degreelatitude (the equator) divides the globe into the Northern and Southernhemispheres.

０８／０３／０５　１１：２２：５８　３１ＨＮ８６６０　００５５　

° °

°

LONGITUDENorth Pole

South Pole

Each longitude 69 miles wide

EasternHemisphere

WesternHemisphere

0 longitude(Greenwich, England)

180 longitude(international date line)

Each time zone equals 15 longitude

47GPScape System

Introduction

Longitudes, also called meridians, are vertical circles extended from theNorth Pole to the South Pole. The zero degree longitude, which passesthrough Greenwich, England, divides the Earth into the Eastern andWestern hemispheres. The 180 degree longitude, half way around theplanet, is the international date line.

０８／０３／０５　１１：２３：０２　３１ＨＮ８６６０　００５６　

48 GPScape System

Introduction

Your ATV GPScape System receives signals from the GlobalPositioning System (GPS), a U.S. government network that orbits theEarth, then uses those signals to calculate your current position as wellas the distance and direction to other locations (destinations).

In addition to latitude and longitude, GPScape also calculates altitude(above sea level).

The primary uses of your GPScape System are:

inputting the latitude and longitude of a destination as a waypointusing the system to guide you to a waypoint

We’re sure you’ll enjoy using your GPScape System. It is an excellentnavigation aid, but successful navigation also requires your carefulattention to the terrain you are riding and your good judgment.

making your current location for future use as a waypoint (navigatingposition)

０８／０３／０５　１１：２３：０９　３１ＨＮ８６６０　００５７　

Using the GPScape System while you are ridingcan take your attention away from the terrain,causing a crash in which you could be seriouslyinjured or killed.

Do not look at the display for more than asecond or so at a time while riding.Stop your ATV if you need more time to lookat the display or operate the system controls.

49GPScape System


Also, be aware that the system can distract your attention from operatingyour ATV if you focus too much on the display or operate the system’scontrols while riding. Do not look at the display unless you decide youcan do so safely.

The GPScape System is designed to provide information to help youreach selected destinations. While this system provides the direction anddistance to a destination, it does not provide an actual path. You mustuse your own observation of the terrain and good judgment in choosinga safe path to reach the destination.

０８／０３／０５　１１：２３：１５　３１ＨＮ８６６０　００５８　

50 GPScape System

System Limitations

Your GPScape System uses signals from the Global Positioning Systemoperated by the U.S. Department of Defense. For security reasons,certain inaccuracies are built into GPS for which your navigation systemmust constantly compensate. This can cause occasional positioningerrors of up to several hundred feet.

Since GPScape receives information from satellites orbiting the Earth,your system’s receiver requires a relatively unobstructed view of the sky.Obstructions that will limit your system’s sky view include (but are notlimited to) buildings, canopies, heavy rain or snow, or tree foliage.

０８／０３／０５　１１：２３：１９　３１ＨＮ８６６０　００５９　

less than 2 hoursmore than 2 hours,less than a month

25 seconds2 minutes

8 minutesmore than a month

Approximate Time for System toAcquire Position Fix AfterTurning Ignition ON

Time Elapsed SinceIgnition Switched OFF

51

Position Fix

System Start-up

GPScape System

System Failure to Display a Position Fix

The GPScape System uses satellite information to compute your presentposition (called a position fix).

Depending on the elapsed time since the ignition was last switched OFF( ), there are three approximate response times for the system toacquire your position fix.

If your ATV is transported with the ignition switch OFF ( ) for over60 miles (100 km) or if your ATV is not started for at least three months,we recommend that you reset your system by following the procedureon the following page, .

０８／０３／０５　１１：２３：２９　３１ＨＮ８６６０　００６０　

－

－

(3)

(1)(1) antenna mark

(2) battery cover(3) bolts

(4) negative ( ) terminal lead(5) battery

(4)(5)

(2)

52

System Failure to Display a Position Fix

System Start-up

GPScape System

Turn the ignition switch OFF ( ).Remove the battery cover ( ) by removing the bolts ( ).

If the receiver does not get a position fix within about 8 minutes(flashing antenna mark ( ) as shown in the illustration), make sure thereare no overhead obstructions (building, trees, canopy, etc.) and thenperform the following:

Disconnect the negative ( ) terminal lead ( ) from the battery ( )and wait for 1 minute.

1.2.3.

1

324 5

０８／０３／０５　１１：２３：３８　３１ＨＮ８６６０　００６１　

－

53GPScape System

System Start-up

Reconnect the negative ( ) terminal lead and install in the reverseorder of removal.If you can not obtain a position fix after performing this procedure,see your Honda dealer.

4.

０８／０３／０５　１１：２３：４２　３１ＨＮ８６６０　００６２　

Not Usable The system is signaling(flashing antenna mark) thatyour position fix is notavailable.

The system has determinedlatitude, longitude, andaltitude. The receiver is readyto provide navigationalinformation.

2D Navigation

3D Navigation

The system has determinedlatitude and longitude, but isunable to determine altitude.2D Navigation is not asaccurate as 3D Navigation.

(1)

(1) satellite status (signal strength indicator )

Display Status

54

Satellite Status

GPScape System

The satellite status indicates the amount of information received fromGPS satellites in one of three possible categories:

If there are large obstacles nearby or overhead, move to a newlocation with a clear view of the sky.

０８／０３／０５　１１：２３：５３　３１ＨＮ８６６０　００６３　

(2)

(2) GPS mark

55

Satellite Status

GPScape System

If the GPS mark ( ) blinks as shown in the illustration.See your Honda dealer to check and restore the GPScape System.

2

０８／０３／０５　１１：２３：５７　３１ＨＮ８６６０　００６４　

56 GPScape System

GPS Mode

A waypoint is a geographical position (location) on the surface of theEarth. GPScape allows you to log up to 100 positions as navigationalwaypoints. You may then use GPScape to show you the direction of anyselected waypoint, and how far you are from that waypoint via straight-line travel.

You may mark such waypoints as home, base camp, your favorite riding,fishing, or hunting spots, as well as locations of wildlife sightings.Because you have 100 waypoints available, you may mark severalintersections or landmarks as waypoints during a trail ride.

０８／０３／０５　１１：２４：０１　３１ＨＮ８６６０　００６５　

(1)GPS mode(directionand mileageto waypoint)

(2)

In any modeotherthan GPS(directionof travel)

(3)

(3) odometer/tripmeterselect button

(4) compass direction indicator

(4)

(1) GPS mode(2) GPS/WP button

57

GPS Mode

GPScape System

The GPS mode ( ) shows the shortest distance to your selectedwaypoint. And, when your ATV is moving (one mph or faster), the GPSmode also displays an electronic arrow to indicate the direction to theselected waypoint.

Any time you are not in the GPS mode, the compass direction indicator( ) will function while your ATV is moving (one mph or faster) (page

).

To change the display to odometer or tripmeter, press and release theodometer/tripmeter select button ( ) while the display is in the GPSmode. The display will change to the previous display mode (odometeror tripmeter).

Push the GPS/WP button ( ) to switch between the GPS mode and theother two modes: odometer and tripmeter.

1

2

3

704

０８／０３／０５　１１：２４：１０　３１ＨＮ８６６０　００６６　

－waypoint number ( )distance to waypoint ( ) ‘‘- - -’’

(3 digits for miles, and ifapplicable, tenths and hundredths,with a floating decimal)

direction to waypoint ( )

(3)

(5)

(1) GPS mode display(2) waypoint number

(4) direction to waypoint(5) GPS mark

(6)

(6) signal strength indicator

(2)

(4)

(1)

(3) distance to waypoint

4

32 0 99

GPS Function Digital Readout

58

GPS Mode Display

GPS Mode

GPScape System

The GPS mode display ( ) includes the following functions:

The GPS mark ( ) appears in the display while the GPS mode isselected. The signal strength indicator ( ) appears as long as the GPSsignal is active.

1

56

０８／０３／０５　１１：２４：２１　３１ＨＮ８６６０　００６７　

(1) waypoint number(2) plus button

(3) minus button

(2)

(1)(3)

59

Waypoint Number Display

GPS Mode

GPScape System

To select a higher waypoint number, press and release the plus button( ).To select a lower waypoint number, press and release the minusbutton ( ).To fast scroll: press and hold the plus or minus button until thedesired waypoint number appears.

A waypoint number ( ) appears in the display when the GPS mode isselected. You can store up to 100 waypoints, numbered from 0-99. Tomark a waypoint, see page .

To select a waypoint number:

63

2

3

1

０８／０３／０５　１１：２４：２９　３１ＨＮ８６６０　００６８　

(2)

(1)

(2) eight-point star

(1) direction to waypoint display

60

Direction to Waypoint Display

GPS Mode

GPScape System

The direction to waypoint display ( ) uses an electronic arrow to pointto your destination. The display has 16 possible directions.

While operating in reverse, GPS will continue to direct you as if yourATV is still moving in a forward direction. However, the system willcalculate an accurate distance and display a directional arrow to theselected waypoint.

When your ATV approaches within about 16 feet of the waypoint, thedirection to waypoint display will change from a directional arrow to aneight-point star ( ) as shown in the illustration.2

1

０８／０３／０５　１１：２４：３６　３１ＨＮ８６６０　００６９　

(3)

(3) antenna mark

61

GPS Mode

GPScape System

If the receiver loses a position fix (because of a large obstacle nearby oroverhead), the direction to waypoint display will disappear as shown inthe illustration and the antenna mark ( ) will flash.

The distance to waypoint display will continue to display the lastvalue shown before the loss of the position fix.

If the receiver reacquires a position fix, the direction to waypointdisplay will appear as shown in the illustration.

3

０８／０３／０５　１１：２４：４２　３１ＨＮ８６６０　００７０　

－－Less than 10 miles

10 miles up to 1,000 miles

(1)

(1) distance to waypoint

10 9990.00 9.99

Range Display

62

Distance to Waypoint

GPScape System

GPS Mode

The distance to waypoint ( ) display shows the straight line distancefrom your present location to the waypoint.

The distance range display shows three numerals with a ‘‘floating’’decimal:

USA: Displays read in mph and miles.Canada: Displays read in km/h and kilometers.

1

０８／０３／０５　１１：２４：４９　３１ＨＮ８６６０　００７１　

(1) GPS/WP button(2) waypoint number(3) plus button

(5)(2)

(1)

(3)

(4)

(4) minus button(5) distance to waypoint

63

Basic Waypoint Selection

GPScape System

GPS Mode

To Mark Your Present Position:

There are two methods for marking waypoints.Basic (to select your current position)Advanced (to input desired destinations)


To select a higher waypoint number ( ), press and release the plusbutton ( ).To select a lower waypoint number, press and release the minusbutton ( ).To fast scroll, press and hold the plus or minus button until thedesired waypoint number appears.

(cont’d)

Use the GPS/WP button ( ) to select the GPS mode.

Press and hold the GPS/WP button ( ) for about 2 seconds, until thewaypoint number and distance to waypoint ( ) flash. Then releasethe button.

1.2.3.

4.

1

3

4

1

2

5

０８／０３／０５　１１：２５：０１　３１ＨＮ８６６０　００７２　

(6) direction to waypoint display

(6)

64

GPS Mode

GPScape System

As soon as you start moving (one mph or faster), the direction towaypoint arrow will appear, pointing toward the selected waypointlocation.

In the 2D Navigation status, the calculated waypoint location maynot be as accurate as 3D Navigation.

Within 5 seconds, to mark your present position, tap (do not hold) theGPS/WP button. (The waypoint will not be set unless the GPS/WPbutton is pressed a second time. Do not hold the GPS/WP buttondown. This will cause the system to transition to the advancedwaypoint entry procedure.)The direction to waypoint display ( ) will light as shown in theillustration.

5.

6

０８／０３／０５　１１：２５：０７　３１ＨＮ８６６０　００７３　

latitude longitude- -°(degrees)- -’(minutes)

- -’(minutes)

- -(seconds)

- -(seconds)

.-’’(tenths ofsecond)

.-’’(tenths ofsecond)

- - -°(degrees)

1

2

3

4

1

2

3

4

(5)

(1) GPS/WP button(2) waypoint number(3) plus button

(4) minus button(5) distance to waypoint

(2)

(1)

(3)

(4)

Advanced Latitude & Longitude Entry Sequence

65

Advanced Waypoint Selection

GPS Mode

GPScape System

To input a waypoint value using latitude and longitude coordinates:

(cont’d)

０８／０３／０５　１１：２５：２０　３１ＨＮ８６６０　００７４　

(6)

(7)

(8)

(6) Northern Latitude(7) Southern Latitude

(8) degree

66 GPScape System

GPS Mode


To select a higher waypoint number ( ), press and release the plusbutton ( ).To select a lower waypoint number, press and release the minusbutton ( ).To fast scroll, press and hold the plus or minus button until thedesired waypoint number appears.

Use the GPS/WP button ( ) to select the GPS mode.

While the display is still blinking, press and hold the GPS/WP buttonagain for about 2 seconds until LAT appears above the WP mark. Thecompass direction indicator will flash Northern Latitude ( ) orSouthern Latitude ( ), indicating the hemisphere. (To switch to theother hemisphere, press either the plus or minus button.)Tap (do not hold) the GPS/WP button. The degree ( ) will beginflashing.

Press and hold the GPS/WP button for about 2 seconds, until thewaypoint number and distance to waypoint ( ) flash. Then releasethe button.

1.2.3.

4.

5.

6.

23

4

67

8

1

5

０８／０３／０５　１１：２５：２９　３１ＨＮ８６６０　００７５　

－－

－－

(9) minute

(10)

(10) second (11) tenths of second (11)

(9)

67

GPS Mode

GPScape System

To select your entry:

To select and enter the seconds ( ) follow the same procedureused in steps .

(cont’d)

To enter the displayed value into the system, tap (do not hold) theGPS/WP button. The next level in the entry sequence will beginflashing.To select and enter the minutes ( ) follow the same procedureused in steps .

To increase, tap the plus button.To decrease, tap the minus button.To fast change in units of 10, press and hold the plus button (toincrease) or the minus button (to decrease) until the desired entryappears.

7.

8.

9.

87

7 89

10. 10

０８／０３／０５　１１：２５：４０　３１ＨＮ８６６０　００７６　

－

(12)

(13)

(12) Eastern Longitude(13) Western Longitude

68

GPS Mode

GPScape System

To select the tenths of a second ( ):

To enter the longitude coordinates, follow the same procedure used insteps .

To increase, tap the plus button.To decrease, tap the minus button.

To enter the displayed tenths of a second in the system, tap (do nothold) the GPS/WP button until LON appears above the WP mark.The compass direction indicator will flash Eastern Longitude ( ) orWestern Longitude ( ).(To switch to the other hemisphere, press either the plus or minusbutton.)

11

1312

11.

12.

13.116

０８／０３／０５　１１：２５：４７　３１ＨＮ８６６０　００７７　

－

69

Determining the Coordinates of Your Current Position

GPS Mode

GPScape System

To Correct Input:

To Change the Coordinates f or an Existing Waypoint Number:Advance Waypoint Selection

If your current position is not already marked, mark it (page ).

Once the 1/10 second longitude entry is completed, you can no longerback up in the sequence to make a correction.

Follow steps under (page ) and‘‘overwrite’’ your previous waypoint.

Press and hold the GPS/WP button until the display begins blinking.While the display is still blinking, press and hold the GPS/WP buttonagain until the display shows LAT degrees and minutes.Tap (do not hold) the GPS/WP button repeatedly to sequence throughthe coordinates display.Tap the GPS/WP button again to return to the distance to waypointdisplay.

Push the GPS/WP button. This reverses the sequence so you can backup and make a correction.

1.2.3.

4.

5.

1 4 65

63

０８／０３／０５　１１：２５：５７　３１ＨＮ８６６０　００７８　

－

－

SouthwestNortheastNorthwest

Southeast

SouthNorth

WestEast

(1)

NSEW

(1) compass direction indicator

NWNESWSE

70

Compass Direction Indicator

GPScape System

The compass direction indicator does not appear when the system is inthe GPS mode. Instead, you will see the direction to waypoint arrowas long as your ATV is moving (one mph or faster).

The compass direction indicator displays 8 possible directions:

The compass direction indicator ( ) shows the heading of your ATVwhen the system is in the odometer or tripmeter mode as long as yourATV is moving (one mph or faster). Your ATV must be moving toallow GPScape to calculate your present direction compared to yourprevious location.

1

０８／０３／０５　１１：２６：０６　３１ＨＮ８６６０　００７９　

(2)

(2) antenna mark

71GPScape System

Compass Direction Indicator

If the receiver loses a position fix (because of a large obstacle nearby oroverhead), the compass direction indicator will disappear as shown inthe illustration and the antenna mark ( ) will flash.

If the receiver reacquires a position fix, the compass direction indicatorwill appear as shown in the illustration.

2

０８／０３／０５　１１：２６：１２　３１ＨＮ８６６０　００８０　

72

Automatic Clock Adjustment

GPScape System

Your ATV digital clock has an automatic adjustment function when thesystem’s satellite status is 3D Navigation (page ).

The system will adjust the digital clock display after receiving the basicUT (universal time, formerly referred to as Greenwich Mean Time) andthen calculating your local time.

The automatic digital clock adjustment will start to function about 1minute after your ATV’s battery is connected and the initial manualclock adjustment is completed.

The automatic time adjustment should be accurate within plus-or-minus5 minutes. To switch between standard and daylight saving time, adjustthe clock manually (page ).

54

26

０８／０３／０５　１１：２６：１８　３１ＨＮ８６６０　００８１　

73

Before Riding

Before Riding

Before each ride, you need to make sure you and your Honda are bothready to ride. To help get you prepared, this section discusses how toevaluate your riding readiness, what items you should check on yourATV, and adjustments to make for your comfort, convenience, or safety.This section also includes important information about loading.

.......................................................................Are You Ready to Ride? ..............................................................................Protective Apparel .

...................................................................................Rider Training ........................................................................Age Recommendation .

...................................................................................No Passengers ..........................................................................No Alcohol or Drugs .

................................................................Is Your ATV Ready to Ride? .............................................................................Pre-ride Inspection .

....................................................................................Modifications .........................................................................................Accessories .

................................................................Accessories & Modifications ............................................................................Loading Guidelines .

..........................................................Cargo and Trailer Information ..............................................................................................Loading .

.....................................................................Load Limits & Guidelines .

747476777778797983838486878788

０８／０３／０５　１１：２６：２９　３１ＨＮ８６６０　００８２　

74

Protective Apparel

Are You Ready to Ride?

Before Riding

Before you ride your ATV for the first time, we urge you to:Read this owner’s manual and the labels on your ATV carefully.Make sure you understand all the safety messages.Know how to operate all the controls.

Before each ride, be sure:You feel well and are in good physical and mental condition.You are wearing an approved motorcycle helmet (with chin straptightened securely), eye protection, and other protective clothing.You don’t have any alcohol or drugs in your system.

For your safety, we strongly recommend that you always wear anapproved motorcycle helmet, eye protection, boots, gloves, long pants,and a long-sleeved shirt or jacket whenever you ride.Although complete protection is not possible, wearing proper gear canreduce the chance of injury when you ride.Following are suggestions to help you choose the proper gear.

Helmets and Eye ProtectionYour helmet is your most important piece of riding gear because itoffers the best protection against head injuries. A helmet should fit yourhead comfortably and securely.

０８／０３／０５　１１：２６：３８　３１ＨＮ８６６０　００８３　

Operating this ATV without wearing anapproved motorcycle helmet, eye protection,and protective clothing could increase yourchances of severe injury or death in the event ofan accident.

Always wear an approved motorcycle helmetthat fits properly and wear eye protection(goggles or face shield), gloves, boots,long-sleeved shirt or jacket and long pants.

75


Before Riding

An open-face helmet offers some protection, but a full-face helmetoffers more. Regardless of the style, look for a DOT (Department ofTransportation) sticker on any helmet you buy (USA only). Alwayswear a face shield or goggles to protect your eyes and help your vision.

Riding pants with knee and hip pads, a riding jersey with paddedelbows, and a chest/shoulder protector.

Off-road motorcycle gloves to help protect your hands.

Sturdy off-road motorcycle boots to help protect your feet, ankles,and lower legs.

In addition to a helmet and eye protection, we also recommend:Additional Riding Gear

０８／０３／０５　１１：２６：４５　３１ＨＮ８６６０　００８４　

Operating this ATV without proper instructioncould increase your risk of an accident whichcould lead to serious injury or death.

Beginning and inexperienced operators shouldcomplete the certified training course offered byHonda. They should then regularly practice theskills learned in the course and the operatingtechniques described in the owner’s manual.

76

Rider Training


Before Riding

Tips & Practice Guide f or the ATVRider

Developing your riding skills is an on-going process. Even if you haveridden other ATVs, take time to become familiar with how this ATVworks and handles. Practice riding the ATV in a safe area to build yourskills. Do not ride in rough terrain until you get accustomed to theATV’s controls, and feel comfortable with its size and weight.

We urge all riders to take a certified course approved by the ATV SafetyInstitute (ASI). For information about the ASI training course nearestyou, call the national toll-free number; (800) 887-2887 (USA only).

Other riding tips can be found in thebooklet that came with your ATV (USA only).

０８／０３／０５　１１：２６：５１　３１ＨＮ８６６０　００８５　

A child using an ATV that is not recommendedfor their age could lose vehicle control whileriding, resulting in severe injury or death.

A child under 16 should never operate an ATVwith engine size greater than 90cc.

Carrying a passenger on this ATV greatlyreduces your ability to balance and control thisATV and could cause a crash and you or yourpassenger could be injured or killed.

Never carry a passenger on this ATV.

77

Age Recommendation

No Passengers


Before Riding

The minimum recommended age for this ATV model is 16. For safety,never let children under 16 years old operate this vehicle.

This ATV is designed as an operator-only vehicle. The long seat isdesigned to allow the rider to change body position, not for carrying apassenger. Never let a passenger ride on the seat or on the front or rearcargo racks.

０８／０３／０５　１１：２６：５７　３１ＨＮ８６６０　００８６　

－－

Operating this ATV after consuming alcohol ordrugs can seriously affect your judgement,cause you to react more slowly, affect yourbalance and perception, and result in seriousinjury or death.

Never consume alcohol or drugs before or whileoperating this ATV.

78

No Alcohol or Drugs

Before Riding


Alcohol, drugs and ATVs don’t mix. Even a small amount of alcoholcan impair your ability to operate an ATV safely. Likewise, drugseven if prescribed by a physician can be dangerous while operating anATV. Consult your doctor to be sure it is safe to operate a vehicle aftertaking medication.

０８／０３／０５　１１：２７：０２　３１ＨＮ８６６０　００８７　

Improperly maintaining this ATV or failing tocorrect a problem before riding can cause acrash in which you can be seriously hurt orkilled.

Always perform a pre-ride inspection beforeevery ride and correct any problems.

79

Pre-ride Inspection

Is Your ATV Ready to Ride?

Before Riding

Engine Oil

RadiatorCoolant

Before each ride, it’s important to inspect your ATV and make sure anyproblem you find is corrected. A pre-ride inspection is a must, not onlyfor safety, but because having a breakdown, or even a flat tire, can be amajor inconvenience.

If your ATV has overturned or been involved in a collision, do not ridethe vehicle until it has been inspected by your Honda dealer. There maybe damage or other problems you cannot see.

Check the following items before you get on the ATV:

Check the level and add oil if needed(page ).Check for leaks.

Check the coolant level and add coolant ifneeded (page ).Check for leaks.

(cont’d)

157

147

０８／０３／０５　１６：０２：０６　３１ＨＮ８６６０　００８８　

80


Before Riding

Driveshaf t Boots

Tires

Fuel

Nuts & Bolts

Underbody &Exhaust System

Air Cleaner HousingDrain Tube

Leaks, Loose Parts

Lights

Cable

Check for damage (page ).

Use a gauge to check the air pressure. Adjust ifneeded. Also look for signs of damage orexcessive wear (page ).

Check the wheels to see that the axle nuts aretightened. Use a wrench to make sure allaccessible nuts, bolts, and fasteners are tight.

Check for, and remove, any dirt, vegetation orother debris that could be a fire hazard orinterfere with the proper operation of thevehicle.

Check for deposits in the drain tube. Ifnecessary, clean the tube (page ) and checkthe air cleaner housing.

Walk around your ATV and look for anythingthat appears unusual, such as a leak or loosecable.

Check the level and add fuel (page ) ifneeded. Also make sure the fuel fill cap issecurely fastened.Check for leaks.

Make sure the headlight, brakelight andtaillight are working properly.

Check the cable housings for wear. Check thefittings for looseness. Replace or tighten asneeded.

142

165

185

190

０８／０３／０５　１１：２７：２４　３１ＨＮ８６６０　００８９　

81


Before Riding

Loading Limits

Cargo

Throttle

Brakes

If you are carrying cargo, also check the following:

Check these items after you get on the ATV:

Make sure you do not exceed the load limits(page ).

Check that all cargo is secure.

Check the freeplay and adjust if needed. Pressthe throttle to make sure it moves smoothlywithout sticking, and snaps shut automaticallywhen it is released, in all steering positions(page ).

Squeeze the front and rear brake levers andstep on the rear brake pedal to check that thecontrols operate normally. Depress the rearbrake pedal several times, then check forproper brake lever freeplay (page ).Make sure there is no brake fluid leakage.

(cont’d)

166

83

179

０８／０３／０５　１１：２７：３４　３１ＨＮ８６６０　００９０　

82


Before Riding

Headlight andHeadlight DimmerSwitch

Engine Stop Switch

Steering

Check for proper function (page ).

Check for proper function (page ).

Check that the wheels turn properly as yousteer the handlebar. Move the handlebar rightand left and check that there is no excessivebacklash.

Remember, be sure to take care of any problem you find, or have yourHonda dealer correct it before you ride.

35

34

０８／０３／０５　１１：２７：４１　３１ＨＮ８６６０　００９１　

Overloading, improper loading, or carrying apassenger can cause a crash and you can beseriously hurt or killed.

Follow all load limits and other loadingguidelines in this manual.

83

Loading

Load Limits & Guidelines

Before Riding

Your Honda was designed as a rider-only ATV. It was not designed tocarry a passenger. It can carry cargo on the cargo racks, however,carrying cargo anywhere else or carrying a passenger could interferewith your balance and control of the ATV.

In addition, exceeding the weight limits or carrying an unbalanced loadcan seriously affect your ATV’s handling, braking and stability. Addingaccessories or making modifications that change this ATV’s design andperformance can also make it unsafe. Also, the weight of anyaccessories will reduce the maximum load the ATV can carry.

More specific information on load limits, accessories, and modificationsfollows.

How much weight you put on your ATV, and how you load it, areimportant to your safety. If you decide to carry cargo, you should beaware of the following information.

０８／０３／０５　１１：２７：４８　３１ＨＮ８６６０　００９２　

84

Cargo and Trailer Information


Before Riding

The following load limits apply to standard equipment only. Modifyingyour ATV, using non-standard equipment, or riding on terrain that is notflat and smooth could further reduce these limits.

The ATV was designed to carry you and a specific amount of cargo.The ATV can be used to tow a trailer and a specific amount of cargowith the installation of Honda Trailer Hitch.

The Hondaline Trailer Hitch Kit contains specific information regardingtrailer towing with the ATV. Towing a trailer without reading thisinformation is not recommended.

Cargo and/or the addition of a trailer will affect the acceleration,braking and handling of the ATV. Do not exceed the recommendedlimits listed below. Follow the guidelines (page ).85

０８／０３／０５　１１：２７：５４　３１ＨＮ８６６０　００９３　

485 lbs (220 kg)

front cargo rack weight limit 66 lbs (30 kg)rear cargo rack weight limit 133 lbs (60 kg)

133 lbs (60 kg)

tow weight limit

tongue weight

tongue and rear cargo weight

maximum weight capacity

===

=

= maximum

850 lbs (385 kg)

30 lbs (14 kg)recommended

85


Before Riding

Tongue weight can be measured with an ordinary bathroom scale. Placethe scale under the tongue, using either a tongue jack or other support tokeep the trailer level.

The weight of added accessories will reduce the maximum cargo weightyou can carry.

(Combined weight of the trailerand all cargo in the trailer)

(Weight on the trailer tongue)

(Combined weight on the trailertongue and on the rear cargo rack)

(includes the weight of the rider, all cargo, and accessories.)

Following are the load limits for your ATV:

０８／０３／０５　１１：２８：０４　３１ＨＮ８６６０　００９４　

86

Loading Guidelines


Before Riding

Carrying cargo or pulling a trailer will affect how your ATV handlesand greatly reduce its ability in accelerating, braking and making turnsand other maneuvers.

Be sure to observe the weight limits and follow these guidelines:Check that the tires are properly inflated.Do not place cargo anywhere on the ATV other than on the front andrear racks. Otherwise, operating stability may be adversely affected.Never ride with a passenger on the front or rear cargo racks. TheATV is not designed to carry a passenger.Use the trailer hitch to tow another vehicle or trailer. Do not tow bytying a rope or cable to the rear rack.Load cargo on the rear rack as far forward as possible. Make surecargo on the front rack does not interfere with handlebar movement.Do not allow cargo to extend beyond the edges of either the front orrear racks.Make sure all cargo is secured before riding.Balance cargo weight evenly on both sides.Never exceed the maximum weight limit.When towing a trailer, take care to maintain balance and stability.Distribute cargo between the front and rear of the trailer to obtain therecommended tongue weight.

Never cross a slope when towing a trailer.Avoid riding on steep slopes when carrying cargo or pulling a trailer.

Allow extra room for starting, stopping and turning whenever youcarry cargo or pull a trailer.

When towing a trailer, select the ESP mode (page ), and choosethe 1st shift position.

102

０８／０３／０５　１１：２８：１６　３１ＨＮ８６６０　００９５　

Improper accessories or modifications cancause a crash in which you can be seriouslyhurt or killed.

Follow all instructions in this owner’s manualregarding accessories and modifications.

87

Accessories

Accessories & Modifications

Before Riding

Modifying your ATV or using non-Honda accessories can make yourATV unsafe.

Before you consider making any modifications or adding an accessory,be sure to read the following information.

We strongly recommend that you use only Honda Genuine Accessoriesthat have been specifically designed and tested for your ATV. BecauseHonda cannot test all other accessories, you must be personallyresponsible for proper selection, installation, and use of non-Hondaaccessories.Check with your Honda dealer for assistance and always follow theseguidelines:

Make sure the accessory does not obscure any lights, reduce groundclearance, limit suspension travel or steering travel, or interfere withoperating any controls.Make sure the accessory does not interfere with your ability to shiftbody position on the seat or operate hand and foot controls.Do not add any electrical equipment that will exceed the vehicle’selectrical system capacity (page ). A blown fuse can cause a lossof lights or engine power (page ).

239225

０８／０３／０５　１１：２８：２３　３１ＨＮ８６６０　００９６　

88

Modifications

Accessories & Modifications

Before Riding

We strongly advise you not to remove any original equipment or modifyyour ATV in any way that would change its design or operation. Suchchanges could seriously impair your ATV’s handling, stability, andbraking, making it unsafe to ride.

We also advise you not to make any modifications or remove anyequipment (such as the USDA qualified spark arrester or emissioncontrol system components) that would make your ATV illegal in yourarea.

Removing or modifying your lights, exhaust system, emission controlsystem, or other equipment can also make your ATV illegal.

０８／０３／０５　１１：２８：２８　３１ＨＮ８６６０　００９７　

89

Basic Operation & Riding


This section gives basic riding instructions, including how to start andstop your engine, and how to use the throttle and brakes. It also providesimportant information on riding with cargo.

To protect your new engine and enjoy optimum performance andservice life, refer to Break-in Guidelines (page ).

(cont’d)

.................................................................................Flooded Engine .....................................Bank Angle Sensor Ignition Cut-off System .

...................................................................................Stalled Engine .

.....................................................Keep Hands and Feet on Controls .............................................................................Off-road Use Only .

........................................................................Safe Riding Precautions .

....................................................................................Control Speed .........................................Use Care on Unfamiliar or Rough Terrain .

......................................................................Do Not Perform Stunts .

........................................................................................Preparation ..............................................................................Starting Procedure .

............................................................Starting & Stopping the Engine .

................................................................How to Stop the Engine .

...................................................................................Shifting Gears .................................................................Using the Recoil Starter .

..............................................................................Riding in Reverse .

240

919192939495969697989899

100101102108

０８／０３／０５　１１：２８：４２　３１ＨＮ８６６０　００９８　

90



..............................................................................................Braking ..............................................................................Riding Your ATV .

................................................................................Making Turns ........................................................................Skidding or Sliding .

.............................................................................Riding Up Hills .........................................................................Riding Down Hills .

.........................................Crossing or Turning on Hills or Slopes ...................................................................Riding Over Obstacles ...................................................................Riding Through Water .

..............................................................................................Parking .

110112112114115119120122123124

０８／０３／０５　１１：２８：５１　３１ＨＮ８６６０　００９９　

Operating this ATV on paved surfaces mayseriously affect handling and control of the ATV,and may cause the vehicle to go out of control.

Never operate the ATV on any paved surfaces,including sidewalks, driveways, parking lots andstreets.

91

Off-road Use Only

Safe Riding Precautions


ATV Saf etyBef ore Riding

Before riding your ATV for the first time, please review thesection beginning on page 1, and the section beginningon page .

Even if you have ridden other ATVs, take time to become familiar withhow this ATV works and handles. Practice in a safe area until you buildyour skills and get accustomed to the ATV’s size and weight.

Your ATV and its tires are designed and manufactured for off-road useonly, not for pavement. Riding on pavement can affect handling andcontrol. You should not ride your ATV on pavement.

When riding off-road, also remember to always obey local off-roadriding laws and regulations. Obtain permission to ride on privateproperty. Avoid posted areas and obey ‘‘no trespassing’’ signs.

(cont’d)

73

０８／０３／０５　１１：２８：５７　３１ＨＮ８６６０　０１００　

Operating this ATV on public streets, roads orhighways could cause you to collide withanother vehicle.

Never operate this ATV on any public street,road or highway, even a dirt or gravel one.

Removing hands from handlebars or feet fromfootpegs during operation can reduce yourability to control the ATV or could cause you tolose your balance and fall off of the ATV.

Always keep both hands on the handlebars andboth feet on the footpegs of your ATV duringoperation.

92

Keep Hands and Feet on Controls



You should never ride your ATV on public streets, roads or highways,even if they are not paved. Drivers of street vehicles may have difficultyseeing and avoiding you, which could lead to a collision. In many statesit is illegal to operate ATVs on public streets, roads and highways.

Always keep both hands on the handlebars and both feet on the footpegswhen riding your ATV. This is important to maintain your balance andto control the vehicle. Removing even one hand from the handlebars orone foot from the footpegs can reduce your ability to control the ATVor could cause you to lose your balance and fall off the ATV.

０８／０３／０５　１１：２９：０３　３１ＨＮ８６６０　０１０１　

Operating this ATV at excessive speedsincreases your chances of losing control of theATV, which can result in an accident.

Always go at a speed that is proper for yourvehicle, the terrain, visibility and other operatingconditions, and your experience.

(1) footpeg

(1)

93

Control Speed



Riding at excessive speed increases the chance of an accident. Inchoosing a proper speed, you need to consider the capability of yourvehicle, the terrain, visibility and other operating conditions, plus yourown skills and experience.

０８／０３／０５　１１：２９：０８　３１ＨＮ８６６０　０１０２　

Failure to use extra care when operating thisATV on unfamiliar terrain could result in the ATVoverturning or going out of control.

Go slowly and be extra careful when operatingon unfamiliar terrain. Always be alert tochanging terrain conditions when operating theATV.

94

Use Care on Unfamiliar or Rough Terrain



Before riding in a new area, always check the terrain thoroughly. Don’tride fast on unfamiliar terrain or when visibility is limited. (It’ssometimes difficult to see obstructions like hidden rocks, bumps, orholes in time to react.)

０８／０３／０５　１１：２９：１３　３１ＨＮ８６６０　０１０３　

Failure to use extra care when operating onexcessively rough, slippery or loose terraincould cause loss of traction or vehicle control,which could result in an accident, including anoverturn.

Do not operate on excessively rough, slipperyor loose terrain until you have learned andpracticed the skills necessary to control the ATVon such terrain. Always be especially cautiouson these kinds of terrain.

Attempting wheelies, jumps, and other stuntsincreases the chance of an accident, includingan overturn.

Never attempt stunts, such as wheelies orjumps. Don’t try to show off.

95

Do Not Perform Stunts



Never ride past the limit of visibility. Maintain a safe distance betweenyour ATV and other off-road vehicles. Always exercise caution, and useextra care on rough, slippery and loose terrain.

You should always operate your ATV in a safe and reasonable manner.When riding, always keep all four wheels on the ground.

０８／０３／０５　１１：２９：１８　３１ＨＮ８６６０　０１０４　

(1)

(2)

(3)(1) ignition switch(2) neutral indicator

(3) engine stop switch

96

Preparation


Starting & Stopping the Engine

Always follow the proper starting procedure described below.

For your safety, avoid starting or operating the engine in an enclosedarea such as a garage. Your ATV’s exhaust contains poisonous carbonmonoxide gas which can collect rapidly in an enclosed area and causeillness or death.

Confirm the following:The transmission is in neutral, and the neutral indicator ( ) is ON.The engine stop switch ( ) is set to RUN ( ).

Before starting, select a level surface and lock the parking brake(page ).Turn the ignition switch ( ) ON ( ).

1.

2. 140

23

０８／０３／０５　１１：２９：２８　３１ＨＮ８６６０　０１０５　

97

Starting Procedure



Any Air Temperature

The engine will not start if the throttle is fully open (because theelectronic control module cuts off the fuel supply).

Press the start button with the throttle completely closed.

This vehicle has a fuel-injected engine with an automatic choke.Follow the procedure indicated below.

０８／０３／０５　１１：２９：３４　３１ＨＮ８６６０　０１０６　

－

98

Flooded Engine

Bank Angle Sensor Ignition Cut-off System



If Your Engine Quits or Won’tStart,

If the engine fails to start after repeated attempts, it may be flooded withexcess fuel. To clear a flooded engine:

Leave the engine stop switch set to RUN ( ).Open the throttle fully.Press the start button for 5 seconds (or operate the recoil starterseveral times).Follow the normal starting procedure.If the engine starts, then open the throttle slightly if idling is unstable.If the engine does not start, wait 10 seconds, then follow steps

again.

If the engine still won’t start, refer topage , .

Your vehicle’s banking (lean angle) sensor system is designed toautomatically stop the engine if the vehicle is overturned.

Before restarting the engine, you must turn the ignition switch to theOFF ( ) position and then back to ON ( ). The engine will notrestart until you perform this procedure.

1.2.3.

4.5.

216215

1 4

０８／０３／０５　１１：２９：４４　３１ＨＮ８６６０　０１０７　

99

Stalled Engine



If the engine stalls, shift into neutral (N) and restart the engine.

If you are unable to shift to neutral (N) from drive (D), you can restartthe engine by squeezing the front brake lever and pressing the startbutton while the vehicle is stopped.

Do not press the throttle lever while starting in gear. Your ATV isequipped with a start inhibitor system that will cut off the ignition if thethrottle is open while attempting to start in gear.

Once you have started the engine, release the front brake lever, thenapply throttle gradually.

０８／０３／０５　１１：２９：４８　３１ＨＮ８６６０　０１０８　

100

How to Stop the Engine



Normal Engine StopTo stop the engine, make sure the transmission is in neutral by checkingthat the neutral indicator lights, then turn the ignition switch OFF ( ).

The engine stop switch should normally remain in the RUN ( )position even when the engine is OFF.

If your ATV is stopped with the engine stop switch OFF ( ) and theignition switch ON ( ), the battery will discharge.

Emergency Engine StopTo stop the engine in an emergency, use the engine stop switch. Tooperate, slide the switch to the OFF ( ) position.

０８／０３／０５　１１：２９：５５　３１ＨＮ８６６０　０１０９　

RIGHT SIDE

(1)

(2)

(1) right side cover (2) starter grip

101

Using the Recoil Starter



The recoil starter is used to start the engine when the battery is low.To operate the recoil starter:

After the engine starts, allow the starter grip to return slowly.

Grasp the starter grip ( ) firmly, then pull it out slowly approximately4 in (100 mm).Pull the grip up briskly and fully.

Unsnap and remove the right side cover ( ).Check that the transmission is in neutral.

If the starter grip does not return smoothly (because of dirt in theassembly), see your Honda dealer.

The engine cannot be started if the battery is disconnected, low or dead.If the engine cannot be started with connecting the battery, charge thebattery (page ).When the engine cannot be started even if the battery is charged, seeyour Honda dealer.

1.2.3.

4.5.

195

12

０８／０３／０５　１１：３０：０５　３１ＨＮ８６６０　０１１０　

102

Shifting Gears


Neutral (N)Use neutral when you start the engine, or if it is necessary to stop brieflywith the engine idling.

Drive (D)

Reverse (R)

Manual shift (ESP) mode:In this mode, you can shift gears much like a manual transmission, butwithout operating a clutch.You can select three forward shift positions by operating the shiftswitches; 1, 2, and 3.The gear position indicator shows the selected position and the drivemode indicator shows ‘‘ESP.’’When you tow a trailer, select the 1st shift position for properperformance.

Automatic shift (AUTO) mode:Use this mode for everyday riding. The transmission automaticallyadjusts to keep the engine at the best speed for riding conditions.The gear position indicator shows ‘‘D’’ and the drive mode indicatordisappears.

Your ATV has three shift lever positions: neutral (N), drive (D), andreverse (R).

Use this position to ride in reverse (page ).

Use this position for normal riding. The following two modes can beselected in the drive (D) position; automatic shift (AUTO) mode andmanual shift (ESP) mode.You can select the desired mode with the drive mode select switch(page ).

108

32

０８／０３／０５　１１：３０：１３　３１ＨＮ８６６０　０１１１　

(2)(1)

(2) drive mode selectswitch

(1) shift lever

103

Shifting Gears


If the shif t lever is moved while the vehicle is moving, the transmissionmay be damaged.

To select the drive mode, operate the drive mode select switch.With the throttle fully closed, the drive mode can be changed duringrunning.

The drive mode select switch ( ) is located on the right handlebarswitches.

The shift lever ( ) is located on the left side of the fuel tank.To shift the shift lever, bring the ATV to a complete stop.

2

1

０８／０３／０５　１１：３０：２０　３１ＨＮ８６６０　０１１２　

(3)

(1)

(1) shift lever(3) gear position indicator

104

Shifting Gears


AUTO Mode

Riding In ReverseShifting to ‘‘N’’ (neutral) or ‘‘R’’ (reverse) is in the same manner asabove. For reverse, refer to the (page ).

When the drive mode is at AUTO, shifting the lever to ‘‘D’’ (drive)provides a 3-speed automatic transmission.

While pulling up the shift lever ( ), shift to ‘‘D.’’Pull down the shift lever and confirm that the lever is locked and thegear position indicator ( ) is showing ‘‘D.’’

1.2.

108

1

3

０８／０３／０５　１１：３０：２７　３１ＨＮ８６６０　０１１３　

UPSHIFTING SEQUENCE

DOWNSHIFTING SEQUENCE

(A)

(A)

(4)

(5)

(4) upshift switch(5) downshift switch

(A) press

105

Shifting Gears


ESP Mode

To upshift the transmission, press the upshift switch ( ) once.To downshift the transmission, press the downshift switch ( ) once.

Two gearshift switches are located next to the left handlebar grip:upshift ( ) and downshift ( ).

With the drive mode set at ESP, shifting the lever to ‘‘D’’ allowsmanual shifting from 1st to 3rd using the gearshift switches.

45

０８／０３／０５　１１：３０：３５　３１ＨＮ８６６０　０１１４　

106

Shifting Gears



After starting the engine and letting it warm up, follow theseprocedures:

Release the parking brake, but continue squeezing the rear brake lever.Release the rear brake lever and increase engine speed by graduallyopening the throttle.

Learning when to shift gears in manual shift (ESP) mode comes withexperience. Keep the following tips in mind:

As a general rule, shift while moving in a straight line.Close the throttle completely before shifting. Improper shifting maydamage the engine, transmission, and drive train.Upshift to a higher gear or reduce throttle before engine rpm (speed)gets too high. Learn the relationship between engine sound and thenormal shifting points.Downshift to a lower gear before you feel the engine laboring(lugging) at low rpm.Avoid downshifting to help slow your ATV when engine rpm is high.Downshifting when engine speed is near its allowable maximum mayover-rev the engine and possibly cause damage.

When speed increases, release the throttle and upshift to 2nd positionby pressing the upshift switch once.Repeat this sequence to progressively upshift to 3rd (top) position.To downshift, press the downshift switch once. Remember to closethe throttle each time you shift to the next lower position.

Bring your ATV to a complete stop, select the ESP mode and shift theshift lever into the ‘‘D’’ position.

1.

2.3.

4.

5.6.

０８／０３／０５　１１：３０：４５　３１ＨＮ８６６０　０１１５　

107

Shifting Gears


To prevent transmission damage, do not coast or tow the ATV forlong distances with the engine off.

Ride in the highest gear that lets the engine run and accelerate smoothly.This will give you good fuel economy and effective emissions control.

Recommended Shift Points

０８／０３／０５　１１：３０：５０　３１ＨＮ８６６０　０１１６　

Improperly operating in reverse could cause youto hit an obstacle or person behind you,resulting in serious injury.

Make sure there are no obstacles or peoplebehind you before selecting reverse gear. Whenit is safe to proceed, go slowly.

108

Riding in Reverse


Your ATV may be equipped with a reverse speed limiter, which helpsthe vehicle to maintain a saf e speed while riding in reverse gear.


If you need to ride in reverse, make sure the area behind you is clear andonly operate the ATV at low speed.

Bring the vehicle to a complete stop, then make sure the transmissionis in neutral.Depress and hold down the brake pedal.Be sure there are no obstacles or people in the way.Shift the shift lever into ‘‘R’’ (reverse) gear.

Release the rear brake pedal.Open the throttle gradually and ride slowly. Do not open the throttlesuddenly or make abrupt turns.

1.

2.3.4.

5.6.

０８／０３／０５　１１：３０：５７　３１ＨＮ８６６０　０１１７　

Applying only the rear brake abruptly whenoperating in reverse gear could cause the frontwheels to lift off the ground and the ATV couldoverturn backwards.

Carefully apply both the front and rear brakeswhen stopping in reverse gear.

109

Riding in Reverse


To stop, close the throttle and gradually apply both the front and rearbrakes. Do not abruptly apply the rear brake by itself.To shift out of reverse and into neutral, shift the shift lever into ‘‘N’’(neutral) gear.

7.

8.

０８／０３／０５　１１：３１：０１　３１ＨＮ８６６０　０１１８　

110

Braking


As a general rule, the front braking system provides about 70 percent oftotal stopping power.

For full braking effectiveness, use both the pedal and leversimultaneously. Using both braking systems will stop your ATV fasterwith greater stability.

When possible, reduce your speed or complete braking before entering aturn. Avoid braking or closing the throttle quickly while turning. Eitheraction may cause one or more wheels to slip and reduce your control ofyour ATV.

Applying the brakes too hard may cause the wheels to lock and slide,reducing control of your ATV. If this happens, release the brakecontrols, steer straight ahead until you regain control, then reapply thebrakes more gently.

Although the front and rear brakes have separate controls, all fourwheels are interconnected when your ATV is in the 4WD mode. Sooperating any brake control in the 4WD mode will cause braking at boththe front and rear wheels.

Gradually increase braking as you feel the brakes slowing your speed.The increase in engine compression from downshifting will help slowyour vehicle when your ATV is in the ESP mode.

To slow or stop, apply the brake lever and brake pedal smoothly, whiledownshifting to match your speed when your ATV is in the ESP mode.

Your ATV is equipped with disc brakes on both front wheels which arehydraulically activated by operating the right brake lever. A single discbrake of the rear drive train is hydraulically activated by depressing thebrake pedal and mechanically activated by operating the left brake lever.

０８／０３／０５　１１：３１：０９　３１ＨＮ８６６０　０１１９　

111

Braking


Riding Your ATV

Your ability to brake in a turn and to brake hard in an emergencysituation are important riding skills.

For information on how to apply the brakes in various riding situations,see the following section, .

Riding with your foot resting on the brake pedal or your hands on thebrake levers may overheat the brakes, reducing effectiveness.

When descending a long, steep grade, use engine compression brakingby downshifting (in the ESP mode), with intermittent use of both brakes.Continuous brake application can overheat the brakes and reduce theireffectiveness.

０８／０３／０５　１１：３１：１５　３１ＨＮ８６６０　０１２０　

Turning improperly can make the ATV go out ofcontrol, causing a collision or overturn.

Always follow proper procedures for turningas described in this owner’s manual.Practice turning at low speeds beforeattempting to turn at faster speeds.Do not turn at excessive speeds.

112

Making Turns

Riding Your ATV


Learn how to turn your ATV properly. Practice the techniques outlinedin this section on level ground and at low speeds until you are confidentin making turns.

０８／０３／０５　１１：３１：２０　３１ＨＮ８６６０　０１２１　

Lean your body to the inside of a turn and forward.

113

Riding Your ATV


To make a turn from a full stop: Apply the throttle gradually when youturn and start up at the same time. Remember to shift your body forwardto make sharp low-speed turns and whenever you turn whileaccelerating from a full stop.

To make a sharp turn at low speed: It helps to shift your body slightlyforward on the seat, and lean inside, as you steer the handlebar. Shiftingweight forward allows the rear wheels to turn easier, and it alsoimproves front-wheel steering.

To make a turn on level ground: Steer the handlebar and lean your bodytoward the inside of the turn. Leaning helps balance the vehicle, and itfeels more comfortable. Leaning into a turn is an important technique tomaster in riding an ATV.

０８／０３／０５　１１：３１：２６　３１ＨＮ８６６０　０１２２　

Skidding or sliding improperly may cause you tolose control of this ATV. You may also regaintraction unexpectedly, which may cause theATV to overturn.

Learn to safely control skidding by practicing atlow speeds and on level, smooth terrain.

114

Skidding or Sliding

Riding Your ATV


The terrain surface can be a major factor affecting turns. Skiddingduring a turn is more likely to occur on slippery surfaces, such as snow,ice, mud and loose gravel. If you skid on ice, you may lose alldirectional control. To avoid skidding on slippery terrain, keep yourspeed low and ride with caution.

If your ATV skids sideways during a turn, steer in the direction of theskid. Avoid hard braking or accelerating until you have regaineddirectional control.

０８／０３／０５　１１：３１：３１　３１ＨＮ８６６０　０１２３　

Operating on excessively steep hills can causethe vehicle to overturn more easily thanoperating on level surfaces or small hills.

Never operate the ATV on hills too steep for theATV or for your abilities.

Climbing hills improperly could cause loss ofcontrol or cause the ATV to overturn.

Always follow proper procedures for climbinghills as described in this owner’s manual.

115

Riding Up Hills

Riding Your ATV


The ATV’s ability to safely climb hills largely depends on the rider’sskill and judgment. Begin by practicing on smooth, gentle slopes. Asyou gain experience, you’ll learn the hazards and your own limitations.You may then proceed to ride on more difficult terrain. However, youmust be able to decide which hills or hazards might cause the ATV tooverturn. Avoid excessively steep hills.

When climbing hills, you must shift weight toward the front wheels tohelp keep them on the ground. To do this, shift your body slightlyforward on the seat and lean forward. For greater weight shift, moveyour body farther forward and lean forward.

０８／０３／０５　１１：３１：３７　３１ＨＮ８６６０　０１２４　

Shift weight forward when climbing hills.

116

Riding Your ATV


Never climb hills with excessively slippery or loose surfaces.Always check the terrain carefully before you start up any hill.

To climb a hill, take a running start in an appropriate gear and speedfor the conditions. Maintain a steady speed as you ascend the hill.Never open the throttle suddenly or make sudden gear changes. TheATV could flip over backward.Never go over the top of any hill at high speed. An obstacle, a sharpdrop, or another vehicle or person could be on the other side of thehill.

０８／０３／０５　１１：３１：４４　３１ＨＮ８６６０　０１２５　

Stalling, rolling backwards or improperlydismounting while climbing a hill could result inthe ATV overturning.

Always follow proper procedures for climbing ahill as described in this owner’s manual.

117

Stalling the ATV and/or Rolling Backwards:

Riding Your ATV


If you incorrectly estimate climbing capability or terrain conditions, theATV may not have enough power or traction to continue uphill. If thishappen, the ATV can stall and/or roll backwards.

What to do if the ATV stalls or rolls backwards when climbing a hill:If you are about to lose all forward speed:

Using the front and rear brakes together, bring the ATV to a stopwith the vehicle pointed straight uphill.Get off the ATV while you continue holding the brakes.Shift into neutral, set the parking brake and turn the engine off.Then assess the situation.

If the ATV starts rolling backwards before you begin braking:Keep your weight uphill.Carefully apply the front brakes first, then carefully apply therear brake. Do not apply either brake abruptly if you are rollingbackwards, or the vehicle may overturn.

If the ATV continues sliding backwards:After you’ve applied the brakes, get off and away from the vehicle.

Remember that operating any brake control in the 4WD mode will causebraking at both the front and rear wheels.

1.2.

1.

2.3.4.

０８／０３／０５　１１：３１：５４　３１ＨＮ８６６０　０１２６　

Body position forbacking down a hill.

Be sure your legs areclear of the wheels.

118

Riding Your ATV


If the hill is too steep or too slippery, or if you have any doubt whetheryou can safely walk the ATV back down the hill, leave the vehiclewhere it is and get help. If possible, block the wheels so the vehicledoesn’t roll backwards.

If the hill is not too steep and you have good footing, you may be ableto walk the ATV back down the hill. Make sure your intended path isclear in case you lose control of the ATV.

Stand with your body facing downhill, beside the vehicle so you canreach the rear brake lever with your right hand.Be sure your legs are clear of the wheels.Check your footing.Slowly and carefully back the ATV down the hill using the rear brakelever to control speed.If you lose control of the ATV, for your safety, get away from thevehicle.

What to do after the ATV has stalled or rolled backwards:

1.

2.

3.

4.

０８／０３／０５　１１：３２：０３　３１ＨＮ８６６０　０１２７　

On downhills, shift your weight back.

Going down a hill improperly could cause lossof control or cause the ATV to overturn.

Always follow proper procedures for going downhills as described in this owner’s manual.

119

Riding Down Hills

Riding Your ATV


It’s usually advisable to descend hills with the ATV pointed straightdownhill. Avoid angles that would cause the vehicle to lean sharply toone side.

As you approach a downhill, stop and survey the terrain below. Neverride past the limit of your visibility. Never go down a hill at high speed.

０８／０３／０５　１１：３２：１０　３１ＨＮ８６６０　０１２８　

Improperly crossing hills or turning on hills couldcause loss of control or cause the ATV tooverturn.

Always follow proper procedures for crossing orturning on slopes as described in this owner’smanual. Avoid crossing steep hills if possible.

120

Crossing or Turning on Hills or Slopes

Riding Your ATV


Use mainly the rear brake to control speed. Avoid using either the frontbrake or rear brake hard or abruptly when riding down hills.

Remember, braking effectiveness is reduced on any hill with a loosesurface.

Riding on hills or slopes is different from riding on level terrain. Becareful when riding on any hill. Make sure that you practice on gentle,smooth slopes before attempting to ride on steeper or more difficultterrain.

Remember that operating any brake control in the 4WD mode will causebraking at both the front and rear wheels.

When you’ve selected a safe downhill path, shift into a lower gear (inthe ESP mode), shift your weight back with your arms extended andbraced against the handlebar, then go down slowly with the throttleclosed.

０８／０３／０５　１１：３２：１６　３１ＨＮ８６６０　０１２９　

Shift weight uphill when crossing slopes.

121

Riding Your ATV


Crossing Hills or SlopesTo maintain balance and stability when riding across a slope, youneed to shift weight toward the uphill side of the vehicle. To do this,move your body off the center of the seat and lean toward the uphillside.On a slippery or loose surface, you may also need to steer slightlyuphill to maintain a straight course across the slope.Avoid crossing hills that are excessively steep, slippery or rough.

Do not make turns on any slopes until you have first mastered thetechniques for making turns on level terrain.

Compared to riding on level ground, you may need to shift moreweight and lean more when making turns on slopes.

Making Turns on Slopes

０８／０３／０５　１１：３２：２３　３１ＨＮ８６６０　０１３０　

Improperly operating over obstacles couldcause loss of control or a collision and couldcause the ATV to overturn.

When you go over obstacles, always followproper procedures as described in this owner’smanual.

122

Riding Over Obstacles

Riding Your ATV


Before operating in a new area, check for obstacles. Watch out forbumps, rain ruts, potholes and other obstacles in the terrain. When youapproach any obstacle, reduce your speed and be prepared to stop.Never try to ride over large obstacles, such as large rocks or fallen logs.

０８／０３／０５　１１：３２：２８　３１ＨＮ８６６０　０１３１　

The ATV tires have some ability to float.Operating this ATV through deep or fast-flowingwater may cause a loss of traction and loss ofcontrol, which could lead to an accident.

Never operate this ATV in fast-flowing water orin water deeper than that specified in this owner’smanual.

123

Riding Through Water

Riding Your ATV


If necessary, apply the brakes repeatedly until they dry out andoperate normally.

Riding through water can make the brakes less effective thannormal, and may reduce stopping ability.

After leaving the water, always test both the front and rear brakes.

Avoid getting the spark plug or air cleaner wet, as this would causethe engine to stop.

Watch out for submerged obstacles and slippery rocks.Proceed through the water at a slow, steady speed.Choose a path where both banks have gradual slopes.

Your ATV is designed to travel through water up to approximately10 inches (254 mm) deep. Before crossing a stream, make sure the wateris not too deep or flowing too fast.

1.2.3.4.

5.

０８／０３／０５　１１：３２：３６　３１ＨＮ８６６０　０１３２　

124

Parking


Parking on a Steep Incline or a Loose or Slippery Surface

Look for level parking area. Make sure the ground surface is firm.After bringing your ATV to a stop, hold the brakes while you shiftinto neutral.Set the parking brake.Turn the ignition switch OFF ( ).

If it is necessary to start the engine when your ATV in gear and isstopped on a grade, rock the vehicle back and forth to allow shifting thetransmission into neutral.

The brakelights are activated by applying the parking brake. When usingthe parking brake, be sure to turn the ignition switch OFF ( ) to avoiddischarging the battery.

If you must park your ATV on a steep incline or loose or slipperysurface, use the following procedure:

While holding the brakes, set the parking brake.Turn the ignition switch OFF ( ) and release the brakes.If the ATV begins to move, either while sitting on it or after youdismount, find a better parking location.If rocks or other objects are available, you can block the wheels asshown for additional security.

1.2.3.

4.

1.2.

3.4.

０８／０３／０５　１１：３２：４５　３１ＨＮ８６６０　０１３３　

125

Servicing Your Honda


Maintenance, replacement or repair of the emission control devicesand systems may be performed by any ATV repair establishment orindividual using parts that are ‘‘certified’’ to EPA standards.

Service Preparations

Bef ore You Service Your Honda

For information about replacing fuses, see page .

(cont’d)

To help keep your ATV in good shape, this section includes aMaintenance Schedule for required service and step-by-step instructionsfor specific maintenance tasks. You’ll also find important safetyprecautions, information on fuels and oils, and tips for keeping yourHonda looking good.

For information about the exhaust emission and noise requirements ofthe U.S. Environmental Protection Agency (EPA), the California AirResources Board (CARB), and Environment Canada (EC),see page .

USA Only

.......................................................The Importance of Maintenance ............................................................................Maintenance Safety .

........................................................Important Safety Precautions .......................................................................Maintenance Schedule .

..........................................................................Maintenance Record .

..................................................Maintenance Component Locations ..............................................................................................Tool Kit .

...................................................................Owner’s Manual Storage .....................................................................................Seat Removal .

127128129130134

135138139140

224

241

０８／０３／０５　１６：０２：１８　３１ＨＮ８６６０　０１３４　

126



Service ProceduresFluids & Filters

Engine

Chassis

Electrical

...................................................................................................Fuel .............................................................................Engine Oil & Filter .

....................................................................................Gear Case Oil ...................................................................................Differential Oil .

..............................................................................................Coolant .........................................................................................Air Cleaner .

..............................................................................................Throttle ..........................................................................................Spark Plug .

................................................................................................Valves ....................................................................................Spark Arrester .

................................................................................................Brakes ...................................................................................................Tires .

............................................................Engine Guards & Skid Plates ................................................................................Driveshaft Boots .

...............................................................................................Battery .

...............................................................................Appearance Care .

141144152154156161

166168171172

174182189190

191

196

０８／０３／０５　１１：３３：１１　３１ＨＮ８６６０　０１３５　

Improperly maintaining this ATV or failing tocorrect a problem before you ride can cause acrash in which you can be seriously hurt orkilled.

Always follow the inspection and maintenancerecommendations and schedules in this owner’smanual.

127

The Importance of Maintenance


Frequent servicing of the air cleaner is especially important to help youavoid a possible costly engine repair.

If your ATV overturns or is involved in a crash, be sure your Hondadealer inspects all major parts, even if you are able to make some repairs.

A well-maintained ATV is essential for safe, economical, and trouble-free riding. It will also help reduce air pollution. Careful pre-rideinspections and good maintenance are especially important because yourATV is designed to be ridden over rough off-road terrain.

To help you properly care for your ATV, this section of the manualprovides a Maintenance Schedule. The service intervals in this scheduleare based on average riding conditions.

０８／０３／０５　１１：３３：１７　３１ＨＮ８６６０　０１３６　

Failure to properly follow maintenanceinstructions and precautions can cause you tobe seriously hurt or killed.

Always follow the procedures and precautionsin this owner’s manual.

128

Maintenance Safety


This section includes instructions on how to perform some importantmaintenance tasks. If you have basic mechanical skills, you can performmany of these tasks with the tools provided with your ATV.

Other tasks that are more difficult and require special tools are bestperformed by professionals. Removing the wheels should normally behandled only by a Honda technician or other qualified mechanic.Instructions are included in this manual only to assist in emergencyservice.

Some of the most important safety precautions follow. However, wecannot warn you of every conceivable hazard that can arise inperforming maintenance. Only you can decide whether or not youshould perform a given task.

０８／０３／０５　１１：３３：２２　３１ＨＮ８６６０　０１３７　

129

Important Safety Precautions

Maintenance Safety


Carbon monoxide poisoning from engine exhaust.

Burns from hot ATV parts.

Injury from moving parts.

Make sure the engine is off before you begin any maintenance orrepairs. This will help eliminate several potential hazards:

Be sure there isadequate ventilation whenever you operate the engine.

Let the engine and exhaust system coolbefore touching.

Do not run the engine unless instructedto do so.Read the instructions before you begin, and make sure you have thetools and skills required.To reduce the possibility of a fire or explosion, be careful whenworking around gasoline. Use only non-flammable solvent, notgasoline, to clean parts. Keep cigarettes, sparks, and flames awayfrom all fuel-related parts.

Remember that your Honda dealer knows your ATV best and is fullyequipped to maintain and repair it. To ensure the best quality andreliability, use only new Honda Genuine Parts or other equivalents forrepair and replacement. If you have the tools and skills required foradditional maintenance jobs, you can purchase an official HondaService Manual (page ).248

０８／０３／０５　１１：３３：２７　３１ＨＮ８６６０　０１３８　

130

Maintenance Schedule


The required Maintenance Schedule that follows specifies how oftenyou should have your ATV serviced, and what things need attention. Itis essential to have your ATV serviced as scheduled to maintain safe,dependable performance and proper emission control.

The service intervals in this Maintenance Schedule are based on averageriding conditions. Some items will need more frequent service if youride in unusually wet or dusty areas or at full throttle. Consult yourHonda dealer for recommendations applicable to your individual needsand use.

Some items in the Maintenance Schedule can be performed with basicmechanical skills and hand tools. Procedures for these items areprovided in this manual. Other items involve more extensive proceduresand may require special training, tools, and equipment. We recommendthat you have your Honda dealer perform these tasks unless you haveadvanced mechanical skills and the required tools and equipment.Procedures for such items in this schedule are provided in an officialHonda Service Manual available for purchase (page ).

If you do not feel capable of performing a given task or need assistance,remember that your Honda dealer knows your ATV best and is fullyequipped to maintain and repair it. If you decide to do your ownmaintenance, use only Honda Genuine Parts or their equivalents forrepair or replacement to ensure the best quality and reliability.

248

０８／０３／０５　１１：３３：３３　３１ＨＮ８６６０　０１３９　

＊＊＊

＊

＊＊

131



Summary of Maintenance Schedule Notes & Procedures:

Perform the pre-ride inspection (page ) and owner maintenance onthis section at each scheduled maintenance period.

Each item on the maintenance schedule requires some mechanicalknowledge. Certain items (particularly those marked and ) mayrequire more technical information and tools. Consult your Honda dealer.

Should be serviced by your Honda dealer, unless you have theproper tools and service data, and are mechanically qualified. Referto the official Honda Service Manual (page ).In the interest of safety, we recommend these items be servicedonly by your Honda dealer.

Service more frequently when riding in dusty areas, sand or snow.Service more frequently after riding in very wet or muddy conditions.Replace every 2 years. Replacement requires mechanical skill.

NOTES:1.2.3.

79

248

０８／０３／０５　１１：３３：４０　３１ＨＮ８６６０　０１４０　

－

－

mikm

NOTE

NOTE 1NOTE 2

NOTE 3NOTE 2

10015020

I

R

Every 600 mi(1,000 km),100 operating hoursor 12 months: R

100 mi (150 km),20 operating hoursor 1 month: R

Refer topage

166161165

168171144

149156

12002000200

IICI

II

RII

6001000100

CI

I

RII

FUEL LINETHROTTLE OPERATIONAIR CLEANERAIR CLEANER HOUSINGDRAIN TUBESPARK PLUGVALVE CLEARANCEENGINE OIL

ENGINE OIL FILTERRADIATOR COOLANTCOOLING SYSTEM

REGULAR

ITEMS

FREQUENCYWHICHEVERCOMESFIRST

INITIAL

INITIAL=

REGULAR=

HOURS

MAINT. INTERVALMAINT.

132



Maintenance Procedures:I: inspect and clean, adjust, lubricate, or replace, if necessaryC: cleanA: adjustL: lubricateR: replace

Should be serviced by your Honda dealer, unless you have the proper tools and service data, andare mechanically qualified. Refer to the official Honda Service Manual (page ).248

０８／０３／０５　１１：３３：４９　３１ＨＮ８６６０　０１４１　

－

－

－－

－

－

mikm

NOTE

NOTE 3

DRIVE SHAFT BOOTSREAR FINAL GEAR CASEOIL AND DIFFERENTIALOILBRAKE FLUIDBRAKE PADS WEARBRAKELIGHT SWITCHBRAKE SYSTEMSKID PLATE, ENGINEGUARDSUSPENSIONSPARK ARRESTERNUTS, BOLTS,FASTENERSWHEELS/TIRESTIE-ROD AND JOINTBOOTSSTEERING SHAFTHOLDER BEARINGSSTEERING SYSTEM

12002000200

II

IIIII

ICI

II

I

I

6001000100

I

I

III

IC

II

10015020

II

I

II

Refer topage

190152154

174177181174189

172

FREQUENCY

ITEMS

WHICHEVERCOMESFIRST

REGULARINITIAL

HOURS

NOTE 1,2

(R:EVERY

2 YEARS)

MAINT. INTERVALMAINT.

133Servicing Your Honda


In the interest of safety, we recommend these items be serviced only by your Honda dealer.

Should be serviced by your Honda dealer, unless you have the proper tools and service data, andare mechanically qualified. Refer to the official Honda Service Manual (page ).248

０８／０３／０５　１１：３３：５８　３１ＨＮ８６６０　０１４２　

134

Maintenance Record


PerformedBy:

Date NotesODO orHOUR

Miles (km) orhours100 (150) or20600 (1,000) or1001,200 (2,000) or2001,800 (3,000) or3002,400 (4,000) or4003,000 (5,000) or5003,600 (6,000) or6004,200 (7,000) or7004,800 (8,000) or800

Keeping an accurate maintenance record will help ensure that your ATVis properly maintained. Retain detailed receipts to verify themaintenance was performed. If the ATV is sold, these receipts should betransferred with the ATV to the new owner. Make sure whoeverperforms the maintenance completes this record. All scheduledmaintenance, including the 100 mile (150 km) or 20 hours initialmaintenance, is considered a normal owner operating cost and will becharged for by your dealer. Use the space under Notes to recordanything you want to remind yourself about or mention to your dealer.

０８／０３／０５　１１：３４：０４　３１ＨＮ８６６０　０１４３　

front brake fluid reservoir

fuel fill cap

front brake lever

throttle lever

rear brake lever/parking brake lever


Maintenance Component Locations

０８／０３／０５　１１：３４：０８　３１ＨＮ８６６０　０１４４　

air cleaner

coolantreservetank

rear brake pedal

battery

air cleanerhousing draintube

rear brake fluidreservoir

front brake caliper

rear brakelight switch

engine oil filter

front brake caliper

differential oil filler capdifferential oil drain plug

fuse boxmain fuse 1main fuse 2other fuses

136 Servicing Your Honda


０８／０３／０５　１１：３４：１３　３１ＨＮ８６６０　０１４５　

spark plug

tool kit

engine oil dipstick

engine oil filler cap

engine oil drain plug

gear case oilfiller capgear case oildrain plug

spark arrester

owner’s manualstorage compartmentair pressure gauge



０８／０３／０５　１１：３４：１７　３１ＨＮ８６６０　０１４６　

(1) tool kit

(3)

(2)

(1)

(3) rubber band(2) tool kit compartment

UNDER SEAT

138

Tool Kit


The tool kit ( ) is stored in the tool kit compartment ( ) under the seat.After using the tools, be sure to use the rubber band ( ) to fasten thetool kit securely.

To access the tool kit, remove the seat (see page ), and then removethe rubber band.

An optional, larger tool kit may be available. Check with your Hondadealer’s parts department.

1 23

140

０８／０３／０５　１１：３４：２３　３１ＨＮ８６６０　０１４７　

(1)

(2)

(3)

(4)

(5)

(6)

LEFT

(7)

(1) owner’s manual(2) storage compartment(3) quick screw(4) lid

(5) air pressure gauge(6) plastic bag(7) rubber band

139

Owner’s Manual Storage


Be careful not to flood this area when washing your ATV.

Your ATV provides storage for the owner’s manual so you’ll have itwith you for easy reference. Store your owner’s manual ( ) in thestorage compartment ( ) at the left side of the front fender.

To open the compartment, turn left the quick screw ( ) and remove thelid ( ).The owner’s manual and air pressure gauge ( ) should be stored in theplastic bag ( ) and fastened with the rubber band ( ).

1

7

2

45

6

3

０８／０３／０５　１１：３４：３０　３１ＨＮ８６６０　０１４８　

(1)

(2)

(5)

(3)

(4) hooks(5) studs

(3)

(1) seat latch(2) seat(3) front prongs

((44))

140

Seat Removal


Saf ety PrecautionsRefer to on page .

Installation

Slide the seat ( ) back and lift it.

RemovalPull the seat latch ( ) at the rear of the seat.

Insert the front prongs ( ) into the hooks ( ) and press the studs ( )into the grommets on the rear fender.Press down on the seat until it locks.

The seat must be removed for the air cleaner, spark plug and fusemaintenance, and access to the tool kit.

1.

2.

1.2.

1

129

2

3 4 5

０８／０３／０５　１１：３４：４０　３１ＨＮ８６６０　０１４９　

unleaded86 (or higher)

typepump octane number

141

Fuel Recommendation


Fuel


We recommend that you use unleaded fuel because it produces fewerengine deposits and extends the life of exhaust system components.

Your engine is designed to use any gasoline that has a pump octanenumber of 86 or higher. Gasoline pumps at service stations normallydisplay the pump octane number. For information on the use ofoxygenated fuels, see page .

Use of lower octane gasoline can cause persistent ‘‘pinging’’ or ‘‘sparkknock’’ (a loud rapping noise) which, if severe, can lead to enginedamage. Light pinging experienced while operating under a heavy load,such as climbing a hill, is no cause for concern.

If pinging or spark knock occurs at a steady engine speed under normalload, change brands of gasoline. If pinging or spark knock persists,consult your Honda dealer.

Never use stale or contaminated gasoline or an oil/gasoline mixture.Avoid getting dirt, dust, or water in the fuel tank.

129

245

０８／０３／０５　１１：３４：４８　３１ＨＮ８６６０　０１５０　

4.44 US gal (16.8 )

(1) fuel fill cap(2) breather tube

(2)

(1)

(4)

(3)

(3) handlebar cover hole(4) filler neck

142

Fuel Capacity

Refueling Procedure

Fuel



Fuel tank capacity:

The tank should be refilled as soon as possible when the E segment inthe fuel gauge flashes.

129

０８／０３／０５　１１：３４：５６　３１ＨＮ８６６０　０１５１　

Gasoline is highly flammable and explosive.You can be burned or seriously injured whenhandling fuel.

Stop the engine and keep heat, sparks andflame away.Handle fuel only outdoors.Wipe up spills immediately.

143

Fuel


Add fuel until the level reaches the bottom of the filler neck ( ).Avoid over filling the tank. There should be no fuel in the filler neck.

If you replace the fuel fill cap, use only a Honda Genuine replacementpart.

To open the fuel fill cap ( ), turn it counterclockwise.Pull the breather tube ( ) out of the handlebar cover hole ( ).

After refueling, turn the fuel fill cap clockwise until it clicks.Insert the breather tube into the handlebar cover hole.

1.2.3.

4.5.

4

12 3

０８／０３／０５　１１：３５：０２　３１ＨＮ８６６０　０１５２　

144

Engine Oil & Filter


Engine oil quality is a major factor that affects both the performanceand the service life of the engine.

Using the proper oil (page ) and filter, and regularly checking,adding, and changing oil will help extend your engine’s life. Even thebest oil wears out. Changing oil helps get rid of dirt and deposits in theengine. Operating the engine with old or dirty oil can damage yourengine. Running the engine with insufficient oil can cause seriousdamage to the engine and transmission.

Change the engine oil as specified in the maintenance schedule onpage . When running in very dusty conditions, oil changes should beperformed more frequently than specified in the maintenance schedule.

145

132

０８／０３／０５　１６：０２：２３　３１ＨＮ８６６０　０１５３　

＊

＊

OKNOT RECOMMENDED

API classification

viscosity (weight)JASO T 903standardsuggested oil

SG or higher except oils labeled asenergy conserving on the circular APIservice label

MASAE 10W-30

Pro Honda GN4 4-stroke oil (USA &Canada), or Honda 4-stroke oil(Canada only), or an equivalentmotorcycle oil.

145

Oil Recommendation

Engine Oil & Filter


(cont’d)

Suggested oils are equal in performance to SJ oils that are not labeledas energy conserving on the circular API service label.

Your ATV does not need oil additives. Use the recommended oil.Do not use oils with graphite or molybdenum additives. They mayadversely affect clutch operation.Do not use API SH or higher oils displaying a circular API ‘‘energyconserving’’ service label on the container. They may affectlubrication and clutch performance.

Do not use non-detergent, vegetable, or castor based racing oils.

０８／０３／０５　１１：３５：１９　３１ＨＮ８６６０　０１５４　

(1) code number of the sales company of the oil(2) oil classification

(1)

(2)

146

Engine Oil & Filter


Other viscosities shown in the following chart may be used when theaverage temperature in your riding area is within the indicated range.

JASO T 903 standardThe JASO T 903 standard is an index for engine oils for 4-strokemotorcycle engines.There are two classes: MA and MB.Oil conforming to the standard is labeled on the oil container. Forexample, the following label shows the MA classification.

０８／０３／０５　１１：３５：２６　３１ＨＮ８６６０　０１５５　

－－

(1)

(2)

(3)

(1) dipstick(2) upper level mark

LEFT SIDE

(3) lower level mark

147

Checking & Adding Oil

Engine Oil & Filter


Saf ety Precautions

Bef ore riding your ATV, check the engine oil level

Refer to on page .

Check the engine oil level each day before operating your ATV and addif needed.

Insert the dipstick without screwing it in, then remove the dipstick andcheck the oil level. The oil level should be between the upper levelmark ( ) and the lower level mark ( ) on the dipstick.

Remove the dipstick ( ) from the front crankcase cover and wipe itclean.

Start the engine in a well-ventilated area and let it idle for 3 5minutes. Stop the engine and wait 2 3 minutes.

Park your ATV on a firm, level surface.

(cont’d)

1.2.

3.

4.

129

3

1

2

０８／０３／０５　１１：３５：３６　３１ＨＮ８６６０　０１５６　

(4)

LEFT SIDE

(5)

(4) oil filler cap lid (5) oil filler cap

148

Engine Oil & Filter


Running the engine with an improper oil level can cause serious enginedamage.

If required, remove the oil filler cap lid ( ) and oil filler cap ( ) andadd the specified oil into the filler cap hole, up to the upper levelmark on the dipstick. Do not overfill.Reinstall the oil filler cap, oil filler cap lid and dipstick.

5.

6.

54

０８／０３／０５　１１：３５：４２　３１ＨＮ８６６０　０１５７　

(1)

UNDER ENGINE

(1) engine oil drain plug

149

Changing Engine Oil & Filter

Engine Oil & Filter


Saf ety Precautions

Using the wrong oil f ilter may result in leaks or engine damage.

Drain the Engine Oil:

Refer to on page .

Your ATV’s oil filter has very specific performance requirements. Use anew Honda Genuine oil filter specified for your model or a filter ofequal quality.

(cont’d)

This procedure requires mechanical skill and professional tools such as atorque wrench and oil filter wrench, as well as a means for disposing ofthe drained fluid (page ). If you do not have the skills or the tools,see your Honda dealer.

With the ATV on level ground, remove the oil filler cap from the leftside of crankcase.Place an oil drain pan under the crankcase and remove the engine oildrain plug ( ).

1.

2.

129

210

1

０８／０３／０５　１１：３５：５０　３１ＨＮ８６６０　０１５８　

13 lbf·ft (18 N·m , 1.8 kgf·m)

(5)

(4) (3)

(2) oil filter bolt(3) oil filter cover

(4) oil filter(5) O-rings

(2)

150

Engine Oil & Filter


Improper installation of the oil f ilter can cause serious engine damage.

Install a New Engine Oil Filter:

Install the oil filter cover and tighten the oil filter bolt. Make sure theoil filter bolt is tightened securely to the specified torque.Oil filter bolt torque:

Check the O-rings ( ) are in good condition and then insert a new oilfilter to the oil filter cover.Use only the Honda Genuine oil filter or a filter of equivalent qualityspecified for your model. Using the wrong Honda filter or a non-Honda filter which is not of equivalent quality may cause enginedamage.

Remove the spring and washer. Do not discard the washer with theold oil filter.Discard the oil filter.

Remove the oil filter bolt ( ) and oil filter cover ( ).Let the remaining oil drain out.Remove the oil filter ( ) from the cover.4

5

3.

4.5.

6.7.

8.

2 3

０８／０３／０５　１１：３５：５９　３１ＨＮ８６６０　０１５９　

－

4.3 US qt (4.1 )

18 lbf·ft (25 N·m , 2.5 kgf·m)

(7)

(6)

(6) drain plug sealing washer (7) O-ring

151

Engine Oil & Filter


Improper disposal of drained f luids is harmf ul to the environment.

Add Engine Oil:

Pour the drained oil into a suitable container and dispose of it in anapproved manner (page ).

Check that the drain plug sealing washer ( ) and O-ring ( ) are ingood condition. If necessary, replace them.

Apply a thin coat of engine oil to the O-ring.Reinstall the engine oil drain plug and tighten it to the specifiedtorque:

If a torque wrench is not used for installation, see your Honda dealer assoon as possible to verify proper assembly.

Check that there are no oil leaks.

Reinstall the oil filler cap.Start the engine and let it idle for 5 minutes.

Fill the crankcase with the recommended grade oil approximately:

Stop the engine and after 2 3 minutes, check the oil level. Makesure the oil is between the upper and lower level marks on the dipstick.If necessary, add more oil but do not overfill.Reinstall the oil filler cap and dipstick.

6 7

9.

10.

12.11.

13.

14.15.16.

17.18.

210

０８／０３／０５　１１：３６：１１　３１ＨＮ８６６０　０１６０　

typeviscosity (weight)

hypoid gear oilSAE 80

suggested oil Honda shaft drive oil or equivalent

152

Changing Oil

Oil Recommendation

Gear Case Oil



Change the oil with the gear case at normal operating temperature toassure complete and rapid draining.

129

０８／０３／０５　１１：３６：１９　３１ＨＮ８６６０　０１６１　

9 lbf·ft (12 N·m , 1.2 kgf·m)

2.7 US oz (80 cm )

(1) oil drain plug(2) oil filler cap

(1)

(3)

(2)

REAR

(3) lower edge of the inspection hole

153

Gear Case Oil


Park the ATV on level ground.Place an oil drain pan under the oil drain plug ( ).Remove the oil filler cap ( ) and the drain plug.After the oil has completely drained, reinstall the drain plug andtighten it to the specified torque:

Fill the gear case with the recommended oil.

Install the oil filler cap.Make sure the oil level is at the lower edge of the inspection hole ( ).

1.2.3.4.

5.

6.7.

12

3

０８／０３／０５　１１：３６：２７　３１ＨＮ８６６０　０１６２　

typeviscosity (weight)

hypoid gear oilSAE 80

suggested oil Honda shaft drive oil or equivalent

154

Oil Recommendation

Changing Oil

Differential Oil



Change the oil with the differential at normal operating temperature toassure complete and rapid draining.

129

０８／０３／０５　１１：３６：３６　３１ＨＮ８６６０　０１６３　

9 lbf·ft (12 N·m , 1.2 kgf·m)

6.1 US oz (180 cm )

(1) oil drain plug(2) oil filler cap

(3)(2)

(1)

FRONT

(3) lower edge of the inspection hole

155

Differential Oil


Park the ATV on level ground.Place an oil drain pan under the oil drain plug ( ).Remove the oil filler cap ( ) and the drain plug.After the oil has completely drained, reinstall the drain plug andtighten it to the specified torque:

Fill the differential with the recommended oil.

Install the oil filler cap.Make sure the oil level is at the lower edge of the inspection hole ( ).

1.2.3.4.

5.

6.

12

3

０８／０３／０５　１１：３６：４４　３１ＨＮ８６６０　０１６４　

156

Coolant Recommendation

Coolant


Using coolant with silicate inhibitors may cause premature wear ofwater pump seals or blockage of radiator passages. Using tap watermay cause engine damage.

Your ATV’s liquid cooling system dissipates engine heat through thecoolant jacket that surrounds the cylinder and cylinder head.

Maintaining the coolant will allow the cooling system to work properlyand prevent freezing, overheating, and corrosion.

Use Pro Honda HP coolant or an equivalent high quality ethylene glycolantifreeze containing corrosion protection inhibitors specificallyrecommended for use in aluminum engines. Check the antifreezecontainer label.

Use only distilled water as a part of the coolant solution. Water that ishigh in mineral content or salt may be harmful to the aluminum engine.

The factory provides a 50/50 solution of antifreeze and water in thisATV. This coolant solution is recommended for most operatingtemperatures and provides good corrosion protection.

Decreasing the concentration of antifreeze to less than 40% will notprovide proper corrosion protection.

０８／０３／０５　１１：３６：５１　３１ＨＮ８６６０　０１６５　

(1)

(1) reserve tank(2) UPPER level mark

(2)

(3)

RIGHT FRONT

(3) LOWER level mark

157

Checking & Adding Coolant

Coolant


Saf ety Precautions

Increasing the concentration of antifreeze is not recommended becauseit decreases cooling system performance. Higher concentrations ofantifreeze (up to 60%) should only be used to provide additionalprotection against freezing. Check the cooling system frequently duringfreezing weather.

Refer to on page .

Check the engine coolant level each day before operating your ATV andadd if needed.

With the engine at normal operating temperature, check the coolantlevel in the reserve tank ( ). It should be between the UPPER ( )and LOWER ( ) level marks.If the reserve tank is empty, or if coolant loss is excessive, check forleaks and see your Honda dealer for repair.

Make sure the vehicle is on level ground.

(cont’d)

1.2.

129

13

2

０８／０３／０５　１１：３６：５９　３１ＨＮ８６６０　０１６６　

FRONT

(4)

(5)

(4) steering cover (5) reserve tank cap


Coolant

Add coolant to the reserve tank as required to bring the coolant levelto the UPPER level mark.

Remove the steering cover ( ) and reserve tank cap ( ).Always add coolant to the reserve tank. Do not attempt to add coolantby removing the radiator cap.

After adding coolant, install the reserve tank cap and steering cover.

3.

4.

5

5.

4

０８／０３／０５　１１：３７：０５　３１ＨＮ８６６０　０１６７　

Removing the radiator cap while the engine ishot can cause the coolant to spray out, seriouslyscalding you.

Always let the engine and radiator cool downbefore removing the radiator cap.

159

Coolant Replacement


Coolant

Saf ety Precautions

You & the Environment,

Improper disposal of drained f luids is harmf ul to the environment.

Refer to on page .

Coolant should be replaced by your Honda dealer, unless you have theproper tools and service data, and are mechanically qualified. Refer tothe official Honda Service Manual (page ).

To properly dispose of drained coolant, refer topage .

129

248

210

０８／０３／０５　１１：３７：１２　３１ＨＮ８６６０　０１６８　

(2)

(4)

(1)

(3)FRONT

(1) tabs(2) radiator cover plate

(3) radiator core(4) oil cooler

160

Radiator Core


Coolant

Saf ety Precautions

To clean the radiator core, oil cooler and radiator cover plate:

Do not apply pressured water directly to the radiator core and oilcooler. The pressured water can damage the radiator core.

Refer to on page .

Check the air passages for clogging or damage. Remove insects, mud, orany obstruction with low water pressure. Have the radiator checked byyour Honda dealer if the air flow is restricted over more than 20% of theradiator surface.

Clean the radiator core after riding the ATV in mud.

Unhook the tabs ( ).Remove the radiator cover plate ( ).Wash the radiator core ( ), oil cooler ( ) and radiator cover plate.

1.2.3.

1

3 4

129

2

０８／０３／０５　１１：３７：２０　３１ＨＮ８６６０　０１６９　

161

Air Cleaner


Saf ety Precautions

Using the wrong air cleaner may result in premature engine wear.

Improper or lack of proper air cleaner maintenance can cause poorperf ormance and premature engine wear.

Refer to on page .

Proper air cleaner maintenance is very important for off-road vehicles.A dirty, water-soaked, worn-out, or defective air cleaner will allow dirt,dust, mud, and other impurities to pass into the engine.

Service the air cleaner more frequently if you ride in unusually wet ordusty areas. Your Honda dealer can help you determine the correctservice interval for your riding conditions.

Your ATV’s air cleaner has very specific performance requirements.Use a new Honda Genuine air cleaner specified for your model or an aircleaner of equal quality.

Proper air cleaner maintenance can prevent premature engine wear ordamage, expensive repairs, low engine power, poor gas mileage, andspark plug fouling.

129

０８／０３／０５　１１：３７：２７　３１ＨＮ８６６０　０１７０　

(1) (3)

(2)

(1) seat latch(2) retainer clips

(2)

(3) air cleaner housing cover

UNDER SEAT

162

Cleaning

Air Cleaner


Remove the seat by pulling the seat latch ( ) up.

Unlatch the retainer clips ( ).Remove the air cleaner housing cover ( ).

1. 1

2.3.

23

０８／０３／０５　１１：３７：３４　３１ＨＮ８６６０　０１７１　

－

UNDER SEAT

(9) (7) (5)

(4)

(8)

(4) element holder(5) screw(6) air cleaner assembly

(7) clamp(8) air cleaner(9) air cleaner body

(6)

163

Air Cleaner


(cont’d)

Unscrew the clamp ( ).Remove the air cleaner ( ) from the air cleaner body ( ).

Loosen the screw ( ) and remove the air cleaner assembly ( ) fromthe air cleaner housing.

Remove the element holder ( ).

Gently wash the air cleaner in clean, non-flammable (high flashpoint) solvent such as kerosene not gasoline. After cleaning, gentlysqueeze out the remaining solvent. Avoid twisting or wringing the aircleaner. This can tear the foam.Inspect for tears or cracks in the foam or seams of the air cleaner.Replace the air cleaner if it is damaged.

4.5.

6.7.8.

9.

64

5

97

8

０８／０３／０５　１１：３７：４２　３１ＨＮ８６６０　０１７２　

UNDER SEAT

(11)

(10)

(10) FRONT mark(11) tab

164

Air Cleaner


Allow the air cleaner to dry thoroughly before applying oil. A wet aircleaner will not fully absorb the oil.Pour clean Pro Honda Foam Filter Oil or an equivalent (Canada:Honda Foam Filter Oil or an equivalent) over the entire surface of theair cleaner. Use both hands to evenly spread the oil into the air cleaner.Gently squeeze out any excess oil. (To keep your hands dry, place theair cleaner in a clean plastic bag before spreading the oil into the aircleaner.)Install the air cleaner on the air cleaner body.Apply a thin coat of grease to the sealing surface of the air cleanerassembly.Install the clamp.Insert the air cleaner assembly into the air cleaner housing.Install the element holder.Fasten the screw.Reassemble by reversing the disassembly sequence.

Install the air cleaner housing cover with the FRONT mark ( )facing forward and fit the tab ( ) at the element holder.

10.

11.

12.13.

14.15.16.17.18.

1011

０８／０３／０５　１１：３７：５２　３１ＨＮ８６６０　０１７３　

(1)(2)

(3)

(1) drain tube(2) clip

(3) air cleaner housing

REAR

165

Air Cleaner Housing Drain Tube

Air Cleaner


The air cleaner housing drain tube should be serviced in accordance withthe Maintenance Schedule. (Riding through water may require morefrequent inspection.) If deposits can be seen in the drain tube, the tubemust be cleaned before starting the vehicle.

Remove the drain tube ( ) by removing the clip ( ) under the aircleaner housing ( ).Drain the deposits.Reinstall the drain tube, securing it with the clip.

1.

2.3.

1 23

０８／０３／０５　１１：３７：５８　３１ＨＮ８６６０　０１７４　

－－

－－

1/8 5/16 in(3 8 mm)

1/8 5/16 in (3 8 mm)

(1)(2) (4)(3)

(1) throttle lever(2) rubber sleeve(3) throttle cable adjuster

(4) lock nut(A) decrease freeplay(B) increase freeplay

RIGHT HANDLEBAR

((AA))

((BB))

166

Throttle Freeplay

Throttle



After adjustment, check for smooth operation of the throttle leverfrom fully closed to fully open in all steering positions.

Tighten the lock nut and reinstall the sleeve.

Loosen the lock nut ( ).Turn the adjuster to obtain the correct freeplay.

Slide the rubber sleeve ( ) back to expose the throttle cable adjuster( ).

Adjustment

Check freeplay at the throttle lever ( ).Freeplay:

Inspection

1.

2.3.4.5.

2

129

43

1

０８／０３／０５　１１：３８：０９　３１ＨＮ８６６０　０１７５　

167

Throttle Inspection

Throttle



Check that the throttle assembly is positioned properly and thesecuring bolts are tight.Check for smooth operation of the throttle lever from fully open tofully closed in all steering positions. If there is a problem, see yourHonda dealer.

Lubricate the cables with a commercially available cable lubricant toprevent premature wear and corrosion.

Check the cables for tension or stress in all steering positions.

Inspect the condition of the throttle cables from the throttle leverdown to the throttle body. If the cable is kinked or chafed, have itreplaced.

1.

2.

3.

4.5.

129

０８／０３／０５　１１：３８：１６　３１ＨＮ８６６０　０１７６　

IFR5L11 (NGK)

IFR6L11 (NGK)VK16PRZ11 (DENSO)

VK20PRZ11 (DENSO)

or

or

standard spark plug

for extended highspeed riding

168

Spark Plug Recommendation

Spark Plug


Using spark plugs with an improper heat range can cause enginedamage.

Use only the recommended type of spark plug in the recommended heatrange.

This ATV uses spark plugs that have an iridium coated center electrode.Be sure to observe the following when servicing the spark plugs.

Do not clean the spark plugs. If an electrode is contaminated withaccumulated objects or dirt, replace the spark plug with a new one.To check the spark plug gap, use only a ‘‘wire-type feeler gauge.’’ Toprevent damaging the iridium coating of the center electrode, neveruse a ‘‘leaf-type feeler gauge.’’Do not adjust the spark plug gap. If the gap is out of specification,replace the spark plug with a new one.

０８／０３／０５　１１：３８：２６　３１ＨＮ８６６０　０１７７　

(3)

(4)

(2)

(1)

UNDER SEAT

(1) screw(2) resonance chamber

(3) rubber cover(4) spark plug cap

169

Spark Plug Inspection & Replacement


Spark Plug


Loosen the screw ( ) and remove the resonance chamber ( ).Remove the seat (page ).

Inspect the electrodes and center porcelain for deposits, corrosion, orcarbon fouling. If the corrosion or deposits are heavy, replace theplug.

Using a spark plug wrench provided in the tool kit, remove the sparkplug.

Disconnect the spark plug cap ( ). Take care to avoid damaging thespark plug wire when disconnecting the cap.

Clean any dirt from around the spark plug base.Unhook the rubber cover ( ).

(cont’d)

Make sure that a 1.2 mm wire-type feeler gauge cannot be insertedbetween the spark plug gap ( ). If the gauge fits in the gap, replacethe plug with a new one.

5.4.

6.

1.2.3.

7.

1 2140

129

8.

4

3

5

０８／０３／０５　１１：３８：３８　３１ＨＮ８６６０　０１７８　

(5) spark plug gap

(5)

170

Spark Plug


An improperly tightened spark plug can damage the engine. If a plug istoo loose, a piston may be damaged. If a plug is too tight, the threadsmay be damaged.

With the plug washer attached, thread the spark plug in by hand toprevent cross-threading.Tighten the spark plug:

If the old plug is good:1/8 turn after it seats.

If installing a new plug, tighten it twice to prevent loosening:First, tighten the plug:NGK: turn after it seats.DENSO: turn after it seats.Then loosen the plug.Next, tighten the plug again:1/8 turn after it seats.

Reinstall the spark plug cap. Take care to avoid pinching any cablesor wires.Install the remaining parts in the reverse order of removal.

1/23/4

a)

b)c)

9.

10.

11.

12.

０８／０３／０５　１１：３８：４６　３１ＨＮ８６６０　０１７９　

0.006 in (0.15 mm)0.013 in (0.33 mm)

171

Valve Inspection

Valves



For those who are mechanically proficient and have the proper tools,instructions on adjusting valve clearances are given in the officialHonda Service Manual. Otherwise, the valves should be adjusted byyour Honda dealer.

Excessive clearance will cause noise. Insufficient clearance will causeloss of power and possibly damage the valves.

Valve clearance should be:intake:exhaust:

129

０８／０３／０５　１１：３８：５２　３１ＨＮ８６６０　０１８０　

REAR

(3) (4)(1) (2)

(1) bolts(2) spark arrester

(3) gasket(4) muffler


Spark Arrester


Allow the engine and muffler to cool.

Regular servicing prevents carbon build up (which can diminish engineperformance) and also complies with USDA regulations for regularmaintenance to assure proper function. The spark arrester preventsrandom sparks from the combustion process in your engine fromreaching the environment.

The spark arrester must be serviced every 100 operating hours tomaintain its efficiency.

Remove the bolts ( ), the spark arrester ( ) and the gasket ( ) fromthe muffler ( ).

1.2.

129

14

2 3

０８／０３／０５　１１：３９：００　３１ＨＮ８６６０　０１８１　

(5) spark arrester screen

(5)

173

Spark Arrester


Install the spark arrester and the gasket in the muffler and tighten thebolts securely.

Use a brush to remove carbon deposits from the spark arrester screen( ). Be careful to avoid damaging the spark arrester screen.The spark arrester must be free of breaks and holes. Replace, ifnecessary. Check the gasket. Replace, if necessary.

3.

4.

5

０８／０３／０５　１１：３９：０６　３１ＨＮ８６６０　０１８２　

Honda DOT 4 Brake Fluidbrake fluid

174

Brake Fluid Recommendation

Brakes


The hydraulic disc brakes (front) and a single hydraulic/mechanical discbrake (rear) on your ATV dissipate the heat generated by the friction ofthe brake pads on the disc as the wheels are slowed.

As the front brake pads wear, brake fluid level will drop. A leak in thesystem will also cause the level to drop.

There are no adjustments to perform, but fluid level and pad wear mustbe inspected periodically. The system must be inspected frequently toensure there are no fluid leaks.

If the brake lever or brake pedal freeplay does not feel within thenormal range while riding, check the brake pads for wear (page ).Worn pads should be replaced. If the pads are not worn beyond therecommended limit, there is probably air in the brake system. See yourHonda dealer to have the air bled from the system.

The recommended brake fluid is Honda DOT 4 Brake Fluid, or anybrake fluid of equal quality and performance. Use fresh brake fluidfrom a sealed container. Be sure to read the label before opening thesealed container. An opened container may be contaminated or mayhave absorbed moisture from the air.

177

０８／０３／０５　１１：３９：１２　３１ＨＮ８６６０　０１８３　

(1)RIGHT HANDLEBAR

(1) LOWER level mark

175

Fluid Level Inspection

Brakes


Saf ety Precautions

Brake f luid can damage plastic and painted surf aces. Handle with care.

Refer to on page .

Front Brake Fluid Level

If your inspection indicates a low fluid level, have your Honda dealeradd the recommended fluid.

Do not add or replace brake fluid, except in an emergency. If you doadd fluid, have your Honda dealer check the system as soon as possible.

With the ATV in an upright position, check the fluid level.

It should be above the LOWER level mark ( ). If the level is at orbelow the LOWER level mark, check the brake pads for wear(page ).

(cont’d)

Worn brake pads should be replaced. If the pads are not worn, have yourbrake system inspected for leaks.

177

129

1

０８／０３／０５　１１：３９：２２　３１ＨＮ８６６０　０１８４　

RIGHT SIDE

(2)

(3)

(2) UPPER level mark (3) LOWER level mark

176

Other Inspections

Brakes


Wipe up spills immediately. Avoid brake fluid contact with skin or eyes.If it comes in contact with your eyes, wash them out with clean waterand immediately call a doctor. If it comes in contact with your skin,wash with clean water and, if necessary, call a doctor.Rear Brake Fluid Level

It should be between the UPPER ( ) and LOWER ( ) level mark. If thelevel is at or below the LOWER level mark, check the brake pads forwear (page ).

Worn brake pads should be replaced. If the pads are not worn, have yourbrake system inspected for leaks.

Make sure there are no fluid leaks.Check for deterioration or cracks in the hoses and fittings. If the hosesare worn or cracked, have them replaced by your Honda dealer.

With the ATV in an upright position, check the fluid level.Remove the right side cover (page ).

178

101

32

０８／０３／０５　１１：３９：３０　３１ＨＮ８６６０　０１８５　

(1)

(2)

(1) wear indicator (2) reference mark

FRONT

177

Brake Pad Wear

Brakes



Brake pad wear will depend upon the severity of usage and ridingconditions. The pads will wear faster in wet or muddy conditions.Inspect the pads visually during all regular service intervals to determinethe pad wear.

Always inspect both pads in both the right and left front brake calipers.

Check the wear indicator ( ). Remove the front wheels (page ). Ifthe wear indicator aligns with the reference mark ( ), both pads must bereplaced, see your Honda dealer for this replacement.

12

129

221

０８／０３／０５　１１：３９：３７　３１ＨＮ８６６０　０１８６　

REAR

(4)

(3)

(3) wear indicator (4) edge of reference mark

178

Brakes


Check the wear indicator. If the wear indicator ( ) aligns with thereference mark ( ), replace both pads as a set, see your Honda dealerfor this service.

34

０８／０３／０５　１１：３９：４１　３１ＨＮ８６６０　０１８７　

－－

－－

1 1 3/16 in(25 30 mm)

1 1 3/16 in (25 30 mm)

(1)

LEFT HANDLEBAR

(1) rear brake lever/parking brake lever

179

Rear Brake Lever Freeplay

Brakes


Inspection

Measure the distance the rear brake lever/parking brake lever ( )moves before the brake starts to take hold. Freeplay (measurement atthe tip of the end of the brake lever) should be:

If necessary, adjust to the specified range.

Depress the rear brake pedal several times.1.2.

3.

1

０８／０３／０５　１１：３９：４８　３１ＨＮ８６６０　０１８８　

(2)

(3)

RIGHT REAR

(2) brake lever adjusting nut(3) brake arm pin

(A)(B)

(A) increase freeplay(B) decrease freeplay

180

Other Inspections

Brakes


Adjustment

Check that the brake lever and brake pedal assemblies are positionedproperly and the securing bolts are tight.Make sure that the brake cables, brake arm, spring, and fasteners arein good condition.

Turn the brake lever adjusting nut ( ), located on the brake operatingrod at the brake caliper. Make sure the cutout on the adjusting nut isproperly seated on the brake arm pin ( ).3

2

０８／０３／０５　１１：３９：５５　３１ＨＮ８６６０　０１８９　

(2)

RIGHT SIDE

((AA))

((BB))

(1) brakelight switch(2) adjusting nut

(1)

181

Brakelight Switch Adjustment

Brakes



Rear Brake Only:Check the operation of the rear brakelight switch ( ) at the right sidebehind the engine from time to time. The brakelight should turn on at0.6 in (15 mm) of pedal stroke. Adjustment is done by turning theadjusting nut ( ). Turn the nut in direction ( ) if the switch operates toolate and in direction ( ) if the switch operates too soon.

1

129

A2B

０８／０３／０５　１１：４０：０２　３１ＨＮ８６６０　０１９０　

Using tires that are excessively worn orimproperly inflated can cause a crash in whichyou can be seriously hurt or killed.

Follow all instructions in this owner’s manualregarding tire inflation and maintenance.

182

Tires


To safely operate your ATV, your tires must be the proper type and size,in good condition with adequate tread, and correctly inflated.

This ATV is equipped with low pressure tubeless tires. Although thetires are designed specifically for off-road use, they are not immune topunctures. Always select your riding area with care.

The following pages give detailed information on how and when tocheck your air pressure, how to inspect your tires for wear and damage,and our recommendations for tire repair and replacement.

０８／０３／０５　１１：４０：０７　３１ＨＮ８６６０　０１９１　

183

Air Pressure

Tires



Properly inflated tires provide the best combination of handling, treadlife, and riding comfort. Generally, underinflated tires wear unevenly,adversely affect handling, and are more likely to fail from beingoverheated. Overinflated tires make your ATV ride harshly, are moreprone to damage from surface hazards, and wear unevenly.

Make sure the valve stem caps are secure. If necessary, install new caps.

129

０８／０３／０５　１１：４０：１２　３１ＨＮ８６６０　０１９２　

－－

3.6 psi(25.0 kPa)

3.6 psi(25.0 kPa)

3.6 psi(25.0 kPa)

3.6 psi(25.0 kPa)WIT

HCA

RGO

NO

CARG

O

REAR

RECOMMENDEDPRESSURE

RECOMMENDEDPRESSURE

FRONT

184

Tires


The recommended ‘‘cold’’ tire pressures are:

Always check air pressure when your tires are ‘‘cold.’’ If you check airpressure when your tires are ‘‘warm’’ even if your ATV has only beenridden for a few miles the readings will be higher. If you let air out ofwarm tires to match the recommended cold tire pressures, the tires willbe underinflated. Be sure to check tire pressure at the riding site, sincechanges in altitude can affect air pressure.

０８／０３／０５　１１：４０：１９　３１ＨＮ８６６０　０１９３　

Operating this ATV with improper tires, or withuneven tire pressure may cause loss of control,and you could be seriously injured or killed.

Always use the size and type tires specified inthis owner’s manual for this vehicle.Always maintain proper tire pressure asdescribed in this owner’s manual.

185

Inspection

Tires


Saf ety Precautions

A manually operated tire pump should be used rather than the highpressure system found in service stations. This will minimize thepossibility of tire damage from overinflation. If you use a high pressuresystem at a service station, add air in small amounts and check thepressure increase frequently to prevent possible tire damage fromoverinflation.

Refer to on page .

Whenever you check the tire pressures, you should also look for:Bumps or bulges in the side of the tire or the tread. Replace any tirethat has a bump or bulge.Cuts, slits, or cracks in the tires. Replace the tire if you can see fabricor cord.

Excessive tread wear.Nails or other foreign objects embedded in the side of the tire or tread.

129

０８／０３／０５　１１：４０：２７　３１ＨＮ８６６０　０１９４　

Replace

New

NewReplace

3/16 in

(4 mm)

3/16 in

(4 mm)

3/16 in (4 mm)3/16 in (4 mm)front

rear

(1) groove depth(2) wear indicator

(3) wear indicatorlocation mark

(1)

(3)

Front

Rear

(2)

186

Tires


Also, if you hit a pothole or other hard object while riding, stop as soonas you safely can and carefully inspect the tires for damage.

Tread Wear

For best performance, you should replace a tire before the tread depth atthe center reaches the following limits:

To check the condition of a tire tread, measure the groove depth ( ) inthe center of the tire, or check the wear indicator ( ).

12

０８／０３／０５　１１：４０：３５　３１ＨＮ８６６０　０１９５　

187

Tire Repair

Tires


Saf ety Precautions

If You Have a Flat Tire,

Refer to on page .

A temporary repair can sometimes be made in an emergency situation.However, since a temporary repair may not hold, you must ride veryslowly, preferably without any cargo, and have the tire replaced orpermanently repaired as soon as possible. (For more information ontemporary repairs, see page .)

A tire that is repaired, either temporarily or permanently, will have lowerspeed and performance limits than a new or undamaged tire.

If you have a tire professionally repaired at a non-Honda facility, werecommend that you have the work checked by your Honda dealer.

A permanent repair, such as an internal plug patch, can be made if a tirehas only a small puncture in the tread area. However you may not beable to safely carry as much weight. If you choose to have a tire repaired,be sure the repair work is performed by a professional.

129

219

０８／０３／０５　１１：４０：４１　３１ＨＮ８６６０　０１９６　

× ★★× ★★

AT25 8R12AT25 10R12

DUNLOP KT511DUNLOP KT515

Installing improper tires on your ATV can affecthandling and stability. This can cause a crash inwhich you can be seriously hurt or killed.

Always use the size and type of tiresrecommended in this owner’s manual.

frontrear

188

Tire Replacement

Tires



The tires that came on your ATV were designed to match theperformance capabilities of your ATV and provide the best combinationof handling, braking, and comfort.

It is best to replace all four tires, however if that is not possible, youmust replace the tires in pairs (front or rear) with tires of the same sizeand type as the originals. Never replace just one tire.

The recommended tires for your ATV are:

When you replace a tire, remember:Have the tire replaced by your Honda dealer if possible.If you have a tire professionally replaced at a non-Honda facility, werecommended that you have the work checked by your Honda dealer.

129

０８／０３／０５　１１：４０：５１　３１ＨＮ８６６０　０１９７　

(2) (1)

(1) engine guard (2) skid plate

189

Engine Guard & Skid Plate



Have the engine guard and skid plate replaced if they are cracked ordamaged. If the guard and plate bolts are loose, tighten them securely.

The engine guard ( ) protects the engine crankcase.The skid plate ( ) protects the frame. Check the guard and plate forcracks, damage or looseness at intervals shown in the MaintenanceSchedule.

129

12

０８／０３／０５　１１：４０：５７　３１ＨＮ８６６０　０１９８　

(1)

FRONT

REAR

(1)

(1) rubber driveshaft boots

190

Driveshaft Boots



Check the rubber driveshaft boots ( ) for damage or leaking grease. Ifnecessary, have your Honda dealer replace them.

1

129

０８／０３／０５　１１：４１：０３　３１ＨＮ８６６０　０１９９　

191

WARNING:Wash your hands after handling.

Battery


Your battery is a maintenance-f ree type and can be permanentlydamaged if the cap strip is removed.

BatteryCharging,

Battery Storage,

Your ATV has a maintenance-free type battery. You do not have tocheck the battery electrolyte level or add distilled water as you wouldwith a conventional-type battery.

Electrical accessories use current from the battery, even when theignition is OFF. Limited operation also allows the battery to discharge.If you have electrical accessories on your ATV or do not ride frequently,we recommend that you charge the battery frequently (see

page ).

If you do not expect to ride your ATV for at least two weeks, werecommend you remove the battery, or at least disconnect the batterycables (negative cable first).

If you plan to store your ATV, see page .

If your battery seems weak and/or is leaking electrolyte (causing slowstarting or other electrical problems), see your Honda dealer.

Battery posts, terminals and related accessories containlead and lead compounds.

192

195

０８／０３／０５　１１：４１：１０　３１ＨＮ８６６０　０２００　

The battery gives off explosive hydrogen gasduring normal operation.

A spark or flame can cause the battery toexplode with enough force to kill or seriouslyhurt you.

Wear protective clothing and a face shield, orhave a skilled mechanic do the batterymaintenance.

192

Battery Storage

Battery


Saf ety Precautions

Battery Charging,

Refer to on page .

If you plan to store your ATV, we recommend you remove the batteryand store it where it can be charged at least every 30 days to maintain itsservice life.

If you do not remove the battery, we recommend disconnecting thebattery cables (negative cable first).

You will get the best storage results from removing the battery and slow(trickle) charging it every 30 days (see page ).

Before you remove the battery, be sure to read all the information thatfollows, as well as the information on the battery label.

129

195

０８／０３／０５　１１：４１：１７　３１ＨＮ８６６０　０２０１　

－＋

－

＋

UNDER SEAT(6)(4)

(3)(5)

(2)

(1)(7)

(1) battery cover(2) bolts(3) rubber band(4) negative ( ) terminal lead

(5) battery(6) positive ( ) terminal lead(7) battery box

193

Battery


The battery is located under the rear fender.

Disconnect the negative ( ) terminal lead ( ) from the battery ( )first, then disconnect the positive ( ) terminal lead ( ).

Release the rings and remove the rubber band ( ).Remove the battery cover ( ) by removing the bolts ( ).Make sure the ignition switch is OFF ( ).

Removal

(cont’d)

1.2.3.4.

1 23

546

０８／０３／０５　１１：４１：２７　３１ＨＮ８６６０　０２０２　

＋－

194

Battery


Charge the battery (see following section), unless you have beenriding regularly.Store your battery in an easy-to-reach location off the floor, in an areaprotected from freezing temperature and direct sunlight.Clean the battery box after removing the battery for storage. Dry thebattery box and, if paint is missing, re-paint the area.Slow charge the battery (see following section) once every 30 days.

InstallationReinstall in the reverse order of removal.Be sure to connect the positive ( ) terminal first, then the negative( ) terminal.Make sure all bolts and other fasteners are secure.

Remove the battery from battery box ( ).5.6.

7.

8.

1.

2.

7

9.

０８／０３／０５　１１：４１：３５　３１ＨＮ８６６０　０２０３　

(1)

(1) ‘‘trickle’’ charger

195

Battery Charging

Battery



Be sure to read the information that came with your battery charger andfollow the instructions on the battery. Improper charging may damagethe battery.

We recommend using a ‘‘trickle’’ charger ( ) for home charging. Theseunits can be left connected for long periods without risking damage tothe battery. However, do not intentionally leave the charger connectedlonger than the time period recommended in the charger’s instructions.

Avoid using an automotive-type battery charger. An automotive chargercan overheat an ATV battery and cause premature damage.

1

129

０８／０３／０５　１１：４１：４２　３１ＨＮ８６６０　０２０４　

－－－－

196

General Recommendations

Appearance Care


Saf ety Precautions

High pressure water (or air) can damage certain parts of your ATV.

Frequent cleaning and polishing will keep your Honda looking newerlonger.Frequent cleaning also identifies you as an owner who values his ATV.A clean ATV is also easier to inspect and service.

Refer to on page .

To clean your ATV, you may use:watera mild, neutral detergent and watera mild spray and wipe cleaner/polishera mild spray and rinse cleaner/degreaser and water

Avoid products that contain harsh detergents or chemical solvents thatcould damage the metal, paint, and plastic on your ATV.If your ATV is still warm from recent operation, give the engine andexhaust system time to cool off.Park in a shady area. Washing your ATV in bright sunlight may causethe finish to fade because water droplets intensify the sun’s brightness.Spotting is also more likely because surface water can dry before youhave time to wipe it off.Clean your ATV regularly to protect surface finishes.We recommend the use of a garden hose to wash your ATV. Highpressure washers (like those at coin-operated car washers) candamage certain parts of your ATV.

After cleaning, inspect for damage, wear, and leaks (fuel, oil, coolantand brake fluid).

129

０８／０３／０５　１１：４１：５１　３１ＨＮ８６６０　０２０５　

197

Washing Your ATV with a Mild Detergent

Appearance Care



Rinse your ATV thoroughly with cool water to remove loose dirt.

Wash your ATV with a sponge or soft towel. As you wash, check forheavy grime. If necessary, use a mild cleaner/degreaser to remove thegrime.

Dry your ATV with a chamois or a soft towel. Leaving water on thesurface to air dry can cause dulling and water spots. As you dry,inspect for chips and scratches.Start the engine and let it idle for several minutes. The engine heatwill help dry moist areas.As a precaution, ride your ATV at a slow speed and apply the brakesseveral times. This will help dry the brakes and restore normalbraking performance.If the inside of the headlight lens appears clouded immediately afterwashing, it should clear after a few minutes of riding.

Fill a bucket with cool water. Mix in a mild, neutral detergent, such asdish washing liquid or a product made especially for washingmotorcycles or automobiles.

After washing, rinse your ATV thoroughly with plenty of clean waterto remove any residue. Detergent residue can corrode alloy parts.

1.2.

3.

4.

5.

6.

7.

129

０８／０３／０５　１１：４２：００　３１ＨＮ８６６０　０２０６　

Apply a spray cleaner/polish andwipe paint, chrome, glass, andclear plastic.Spray any difficult-to-reach or verydirty areas with a spray cleaner/degreaser.Rinse and dry.Apply a spray cleaner/polish andwipe with a non-abrasive cloth.Use a spray cleaner/degreaser. Ifnecessary, rub with a sponge.Rinse and dry.Apply a spray cleaner/polish andwipe with a non-abrasive cloth.Apply a high quality chrome/aluminum polish and wipe with anon-abrasive cloth.

Dull, corroded chromeor aluminum.

Heavy grime. Oil leaks.Brake dust.

Light road grimes.

Dust and fingerprintsmudges.

ATV condition Recommended Cleaning

198

Spray Cleaning Your ATV

Appearance Care



Avoid using spray cleaner products on the tires or suspensioncomponents.

Suggestions for using spray cleaner(s) follow:

129

０８／０３／０５　１１：４２：１１　３１ＨＮ８６６０　０２０７　

199

Aluminum Wheel Maintenance

Appearance Care



Aluminum may corrode from contact with dirt, mud, or road salt. Cleanthe wheels after riding through any of these substances. Use a wetsponge and mild detergent. Avoid stiff brushes, steel wool, or cleanerscontaining abrasives or chemical compounds.

After washing, rinse with plenty of water and dry with a clean cloth.Then apply a mild, commercially available spray cleaner/polish or wax.

For stained or dull-looking wheels, use a quality chrome/aluminumpolish to restore the finish.

129

０８／０３／０５　１１：４２：１６　３１ＨＮ８６６０　０２０８　

200

Finishing Touches

Appearance Care



If a surface on your ATV is chipped or scratched, your Honda dealerhas touch-up paint to match your ATV’s color. Be sure to use yourATV’s color code (page ) when you buy touch-up paint.

After washing your ATV, consider using a commercially available spraycleaner/polish or quality liquid or paste wax to finish the job. Use only anon-abrasive polish or wax made specifically for motorcycles orautomobiles. Apply the polish or wax according to the instructions onthe container.

If the frame has a chip that exposes the metal, first apply primer (toprevent corrosion) and then apply the touch-up paint. Several thinlayers of touch-up paint are better than one thick coat.

129

235

０８／０３／０５　１１：４２：２１　３１ＨＮ８６６０　０２０９　

201

Tips

Tips

Here’s helpful advice on how to prepare for an off-road adventure, howto transport and store your Honda, and how to be an environmentallyresponsible ATV owner.

..........................................................................Preparing for a Ride .

.................................................................Transporting Your Honda .

....................................................................You & the Environment ...........................................................................Storing Your Honda .

..................................................What to Take to the Riding Area ..............................................................What to Take on the Trail .

202202203204206210

０８／０３／０５　１１：４２：２８　３１ＨＮ８６６０　０２１０　

202

What to Take to the Riding Area

Preparing for a Ride

Tips

Taking Care of the Unexpected,

A safe and enjoyable ride begins with good planning and preparation.Always ride with at least one other person in case you have trouble, andlet someone know where you’re going and when you expect to return.

Before riding in an unfamiliar area, find out in advance if you needspecial permits, get maps so you can study the terrain, and talk to otherriders who know the area. The Forest Service and the Bureau of LandManagement (USA only), the Ministry of Natural Resources (Canadaonly), riding clubs, and off-road magazines are good sources ofinformation.

Along with your ATV and riding gear, you should take along some toolsand supplies in case you have a problem. For some of the difficultiesyou might encounter, see which beginson page .

We recommend that you always take water, food, a first aid kit, andyour owner’s manual. Other items you should consider loading on yourtruck or trailer include:

a tool kittire repair supplies and tools, and tiresextra parts, control levers, cables, and spark plugswire, duct tape, and ropeextra gasoline

For safety, all refueling should be done at a gas station on the way to theriding area or at your base camp.

211

０８／０３／０５　１１：４２：３６　３１ＨＮ８６６０　０２１１　

203

What to Take on the Trail

Preparing for a Ride

Tips

What you take with you during a ride depends on the kind of terrain,how long you expect to ride, how far you might go from your basecamp or help, and how experienced you or your companions are inmaking repairs.

If you decide to take some tools, spare parts, or other supplies on thetrail, be sure you can carry them safely and know how to use them. Also,be sure to follow the loading guidelines and weight limit (page ).85

０８／０３／０５　１１：４２：４１　３１ＨＮ８６６０　０２１２　

204

Transporting Your Honda

Tips

Do not tow your ATV behind a car or other vehicle.

When you transport your ATV, we recommend that you carry thevehicle in its normal operating position (on all four wheels). Do notincline the vehicle upright on its rear end. This can damage the vehicle,and leaking gasoline could be a hazard.

Follow these procedures:Set the parking brake.1.

０８／０３／０５　１１：４２：４６　３１ＨＮ８６６０　０２１３　

(2)

(1)

(1) front cargo rack (2) rear cargo rack

205

Transporting Your Honda

Tips

Secure the vehicle with tie-down straps in the areas shown.Suitable tie-down straps are available from your Honda dealer.Ordinary rope is not recommended because it can stretch underload.

Rock the vehicle back and forth to make sure the tie-down straps aretight and the vehicle is secure.

Using tie-down straps in any other areas can damage your ATV.

2.

3.

０８／０３／０５　１１：４２：５４　３１ＨＮ８６６０　０２１４　

206

Storing Your Honda

Tips

Honda MotorcycleWinter Storage Guide,

If you won’t be riding for an extended period, such as during the winter,thoroughly inspect your ATV and correct any problem before storing it.That way, needed repairs won’t be forgotten and it will be easier to getyour ATV running again.

For more information about storage, refer to theavailable from your Honda dealer (USA only).

We suggest you perform the following procedures to keep your ATV intop condition. These storage procedures will reduce the deteriorationthat can occur during storage.

０８／０３／０５　１１：４２：５８　３１ＨＮ８６６０　０２１５　

－

207

Preparation for Storage

Storing Your Honda

Tips


This procedure requires a means for draining and disposing of drainedfuel (page ).

Change the engine oil and filter (page ).Make sure the cooling system is filled with a 50/50% antifreezesolution (page ).Fill the fuel tank. Make sure the fuel fill cap is properly installed.To prevent rusting in the cylinders, perform the following:

Remove the spark plug cap from the spark plug.Remove the spark plug.Do not connect the spark plug to the spark plug cap.Pour a tablespoon (15 20 cc) of clean engine oil into thecylinder and cover the spark plug hole with a piece of cloth.With the engine stop switch in the RUN ( ) position, press thestart button several times to crank the engine and distribute the oil.Reinstall the spark plug and spark plug cap.

(cont’d)

129

149

156

2101.2.

3.4.

０８／０３／０５　１１：４３：０８　３１ＨＮ８６６０　０２１６　

The battery gives off explosive hydrogen gasduring normal operation.

A spark or flame can cause the battery toexplode with enough force to kill or seriouslyhurt you.

Wear protective clothing and a face shield, orhave a skilled mechanic do the batterymaintenance.

208

Storing Your Honda

Tips

Remove the battery and charge it fully. Store it in an area protectedfrom freezing temperatures and direct sunlight. Slow charge thebattery (page ) once a month.

Wash and dry your ATV. Wax all painted surfaces.Inflate the tires to their recommended pressures (page ).Store your ATV in an unheated area, free of dampness, away fromsunlight, with a minimum of daily temperature variation.Place your ATV on blocks to lift all tires off the floor.Cover your ATV with a porous material. Avoid using plastic orsimilar non-breathing, coated materials that restrict air flow and allowheat and moisture to accumulate.

5.

6.7.8.

9.

195

10.

183

０８／０３／０５　１１：４３：１５　３１ＨＮ８６６０　０２１７　

－

－

209

Removal from Storage

Storing Your Honda

Tips


Uncover and clean your ATV.

If your ATV has been stored for more than two months ask yourHonda dealer to drain and replace the fuel.

Perform a pre-ride inspection (page ), then test-ride your ATV atlow speeds.

Charge the battery (page ) as required. Install the battery.

If your ATV has been stored for more than four months changethe engine oil (page ).

1.2.

3.

4.5.

129

149

79195

０８／０３／０５　１１：４３：２３　３１ＨＮ８６６０　０２１８　

210

Tread Lightly.

Keep the Noise Down.

Choose Sensible Cleaners.

Recycle Wastes.

You & the Environment

Tips

Owning and riding an ATV can be enjoyable, but you must do your partto protect nature. When you show respect for the land, wildlife, andother people, you also help preserve the sport of off-road riding.

Following are tips on how you can be an environmentally responsibleATV owner.

Stay on existing roads and trails, avoid surfaces thatare easily damaged, and ride only in areas approved for off-roadvehicles.

Loud vehicles can be offensive. Ride asquietly as possible, don’t remove your spark arrester, and don’tmodify the muffler or any other part of your air intake and exhaustsystems. Such modifications not only increase noise, they also reduceengine performance and may be illegal.

Use a biodegradable detergent when youwash your ATV. Avoid aerosol spray cleaners that containchlorofluorocarbons (CFCs) which damage the atmosphere’sprotective ozone layer. Don’t throw cleaning solvents away; see thefollowing guidelines for proper disposal.

It’s illegal and thoughtless to put used engine oil inthe trash, down a drain, or on the ground. Used oil, gasoline, andcleaning solvents contain poisons that can hurt refuse workers andcontaminate our drinking water, lakes, rivers, and oceans. Beforechanging your oil, make sure you have the proper containers. Put oiland other toxic wastes in separate sealed containers and take them to arecycling center. Call your local or state office of public works orenvironmental services to find a recycling center in your area, and toget instructions on how to dispose of non-recyclable wastes.

０８／０３／０５　１１：４３：２９　３１ＨＮ８６６０　０２１９　

211

Taking Care of the Unexpected


Preparing f or a Ride

With all the challenges you can encounter off-road, there’s a chance thatsometime something may go wrong. This section gives practical adviceto help you deal with a wide range of problems. Take time to read thissection before you ride. Also review the tips in(page ).

............................................................................General Guidelines ..................................................If Your Engine Quits or Won’t Start .

..............................If the Transmission Is Not Functioning Properly ......................................................................If You Have a Flat Tire .

.....................If the High Oil/Coolant Temperature Indicator Lights ..................................................................................If a Fuse Blows .

......................................................................................If You Crash .......................................................................If You Lose Your Key .

.........................................................If the Battery Is Low (or Dead) ..........................................................................If a Component Fails .

202

212215217219223225229230231232

０８／０３／０５　１１：４３：３８　３１ＨＮ８６６０　０２２０　

－－

212

General Guidelines



Keeping your ATV well-maintained is the best way to reduce thepossibility of having a problem while riding. However, problems canarise even with well-maintained machines.

Remember to take along your owner’s manual, the tool kit that camewith your ATV, and any other items (such as tire repair supplies andadditional tools) that might help you solve a problem on your own.

If something goes wrong during a ride, the first thing to do is stop assoon as you safely can. Do not continue riding if you have a flat tire, oryou hear an unusual noise, or your ATV just doesn’t feel right. If youcontinue riding, you could cause more damage and endanger your ownsafety.

After stopping, take time to assess the situation. Carefully inspect yourATV to identify the problem, then consider your options before youdecide what to do.

If a problem is relatively minor and you have the tools, supplies, andskills to make a permanent repair, you may be able to fix it on the trailand continue riding. Or, you may be able to make a temporary repairthat allows you to slowly ride back to your base where you can make apermanent repair or get help.

When a problem is more serious or you don’t have the tools, supplies,experience, or time to deal with it you need to choose the safest way toget yourself and your ATV back to base. For example, if you are closeenough, you (or you and another person) might be able to push it back.

０８／０３／０５　１１：４３：４４　３１ＨＮ８６６０　０２２１　

213



Should you ever have a problem while riding, please follow theseguidelines:

Always put personal safety first.Take time to assess the situation and your options before decidingwhat to do.If the problem is relatively minor and you have the tools, supplies,and skills to make a temporary repair, be sure to have permanentrepairs made as soon as possible.Do not continue riding if you are hurt or your ATV is not in saferiding condition.

Additional recommendations for specific problems follow.

０８／０３／０５　１１：４３：５０　３１ＨＮ８６６０　０２２２　

－－

214 Taking Care of the Unexpected

If Your Engine Quits or Won’t Start

Starter motor doesn’t operate

Starter motor works, but the engine won’t start

Proper operation and maintenance can prevent starting and engineperformance problems. In many cases, the cause of the problem may bea simple operational oversight.

If you have a problem starting the engine or experience poor engineperformance the following information may help you. If you can’tcorrect the problem, see your Honda dealer.

If your ATV won’t start, listen as you press the start button. If you don’thear the starter motor turning, refer to thesymptom. If you can hear the starter motor working normally, refer tothe symptom.

０８／０３／０５　１１：４３：５５　３１ＨＮ８６６０　０２２３　

SYMPTOM:POSSIBLE CAUSEignition switch OFFengine stop switchOFFtransmission not inneutralblown fuse

faulty starter motor

WHAT TO DOTurn the ignition switch ON.Turn the engine stop switch to RUN.

Shift into neutral.

Replace with a new fuse of thesame rating (page ).Tighten the battery lead.Charge the battery (page ).If charging doesn’t help, see yourHonda dealer.If all possible causes are negative,the starter motor may be faulty. Seeyour Honda dealer.

SYMPTOM:

POSSIBLE CAUSEout of fuelflooded engineloose orunconnected sparkplug caploose battery cablesweak battery

WHAT TO DOFill the fuel tank.See (page ).Install the spark plug cap securely. Ifthe engine still won’t start, see yourHonda dealer.Tighten the battery terminal bolts.Charge the battery (page ). Ifcharging doesn’t help, see yourHonda dealer.

battery lead looselow (or dead) battery 195

195

98

225

Starter motor doesn’t operate.

Starter motor works, but the engine won’tstart.

Flooded Engine

215



０８／０３／０５　１１：４４：１３　３１ＨＮ８６６０　０２２４　

SYMPTOM:POSSIBLE CAUSE WHAT TO DOhigh oil/coolanttemperature

Check the high oil/coolanttemperature indicator. Refer to

page .runs erratically,misfires

See your Honda dealer.

blubbers (rich fuelmixture)


sooty exhaust (richfuel mixture)


detonates or pingsunder load

If applicable, switch to therecommended octane gasoline(page ) or change your brand ofgasoline. If the problem persists, seeyour Honda dealer.

afterfires (backfires) See your Honda dealer.pre-ignition (runs onafter ignitionswitched OFF)


141

223

Engine starts, but runs poorly.

Ifthe High Oil/ CoolantTemperature Indicator Lights,

216



０８／０３／０５　１１：４４：２５　３１ＨＮ８６６０　０２２５　

217Taking Care of the Unexpected

If the Transmission Is NotFunctioning Properly

Manual Shift (ESP) Mode:

Automatic Shift (Auto) Mode:

(cont’d)

If one or both shift switches do not function, stop riding your ATV inthe ESP mode. Switch to riding in the AUTO (automatic shift) mode.Have your ATV inspected and repaired by your Honda dealer.

Stop the ATV.Turn the ignition switch to the ‘‘OFF’’ ( ) position.After the engine stops, turn the ignition switch to the ‘‘ON’’ ( )position.Check the gear position indicator.

If the gear position indicator shows ‘‘- -’’ and blinks while riding,perform the following:

When the automatic transmission is not shifting properly, the gearposition indicator will show ‘‘- -’’ and blink.

See your Honda dealer to check and restore the automatic transmission.

When the ‘‘- -’’ is blinking on the gear position indicator:Restart the engine; drive the vehicle to a location where it can be loadedand transported to a Honda dealer.

When the display on the gear position indicator returns to normal:You may drive the vehicle as usual after restarting the engine.However, we urge you to have your ATV inspected by your Hondadealer.

1.2.3.

4.

０８／０３／０５　１１：４４：３３　３１ＨＮ８６６０　０２２６　

(2)

(3)

(1)

(1) screw(2) lock plate

(3) emergency valve

LEFT SIDE

218 Taking Care of the Unexpected

If the Transmission Is NotFunctioning Properly

Although ‘‘- -’’ is not blinking in the gear position indicator, the vehicledoes not move:If your ATV won’t move, it is possible the transmission is locked. Usethe following procedure to unlock the transmission.

Shift the shift lever in neutral (N) position.Apply the parking brake.Turn the ignition switch to the ‘‘OFF’’ ( ) position.Loosen the screw ( ) and release the lock plate ( ).Turn the emergency valve ( ) all the way in. With the engine running,your ATV will move forward slowly at idle.See your Honda dealer as soon as possible.

1.2.3.4.5.

6.

213

０８／０３／０５　１１：４４：３９　３１ＨＮ８６６０　０２２７　

219

If You Have a Flat Tire


How you handle a flat tire on the trail depends on how serious the tiredamage is, and what tools and supplies you have with you.

If you have a slow leak or a minor puncture, use the plug method tomake a temporary repair. (The plug method is applied from the outsideof the tire and is the same as that for conventional tubeless tires.)

A plug-type repair kit, available at most auto parts stores or servicestations, provides a plug, an installation tool, tire cement, and aninstruction sheet. Follow the instructions provided with the repair kit tomake a temporary repair.

As soon as possible, have the tire permanently repaired by your Hondadealer. Any tire that cannot be repaired should be replaced.

Whenever the ATV is to be operated far from service facilities oravailable transportation, we recommend that you carry a tire pump and arepair kit with the vehicle.

If the leak is more serious, or a temporary repair doesn’t hold, the tiremust be replaced. The tire will also need to be replaced if it is damaged(page ). Replacing a tire involves removing and re-installing thewheel (page ).

If you are unable to repair a flat tire on the trail, you will need to sendfor help. We strongly recommend that you do not try to ride with a flattire. The ATV will be hard to handle, and if the tire comes off the rim, itmay lock up the wheel and cause you to crash.

186221

０８／０３／０５　１１：４４：４６　３１ＨＮ８６６０　０２２８　

Riding your ATV with a temporary tire repair canbe risky.

If the temporary repair fails, you can crash andbe seriously injured or killed. If you must ridewith a temporary tire repair, ride slowly andcarefully until the tire is permanently repaired orreplaced.

220



０８／０３／０５　１１：４４：５０　３１ＨＮ８６６０　０２２９　

－－

(1)

(1) wheel nuts

(2)

(2) wheel rim

(1)

221

Emergency Wheel Removal/Installation




Park your ATV on a firm, level surface.Removal

(cont’d)

Avoid getting grease, oil, or dirt on the disc or pad surfaces whenremoving and installing each wheel. Any contamination can causepoor brake performance or rapid pad wear after reassembly.

Remove the wheel.Remove the wheel nuts.

Raise the front (or rear) wheels off the ground and place a supportblock under the vehicle.

Loosen but do not remove the wheel nuts ( ).

129

11.2.3.

4.5.

０８／０３／０５　１１：４４：５９　３１ＨＮ８６６０　０２３０　

47 lbf·ft (64 N·m , 6.5 kgf·m)

222



InstallationPosition the wheel.Position the wheel nuts so that the tapered sides face the wheel rim( ).Hand-tighten the wheel nuts on the wheel, then lower the ATV to theground before tightening the nuts in a crisscross (rather than circular)pattern to the specified torque:

If a torque wrench was not used for installation, see your Honda dealeras soon as possible to verify proper assembly. Improper assembly maylead to loss of braking capability.

1.2.

3.2

０８／０３／０５　１１：４５：０５　３１ＨＮ８６６０　０２３１　

223

If the High Oil/Coolant TemperatureIndicator Lights


Continuing to ride with low oil pressure or an overheated engine cancause serious engine damage.

Normally, the high oil/coolant temperature indicator will only lightmomentarily when you turn the ignition ON ( ). Occasionally, it mayflicker at or near idling speed.High oil/coolant temperature may be caused by restriction of air flow tothe radiator (such as mud caked on the radiator), extended idling, an oilleak, a coolant leak, a low oil level, a low coolant level, or extendedoperation under adverse conditions.If the indicator comes on while you’re riding, don’t ignore it. Pull safelyto a stop. Stop the engine as soon as it’s safe to do so, and let it cool.

If there’s no obvious problem, leave the engine on so the fan andcoolant circulating system can continue working. Monitor the highcoolant temperature indicator. The indicator may turn off after a briefstop with no load on the engine.

Check for any restriction of air flow to the radiator.

A steaming engine indicates a coolant leak. Shut the engine off andwait until the steaming stops. Look for a leak, but don’t touch theengine or radiator system. Let everything cool off first.

Check the radiator fan.If the fan is not working, turn the engine off. Open the fuse box(page ) and check the radiator fan fuse. If the fuse is blown,replace it with the proper (same rating) spare fuse. Start the engine. Ifthe high coolant temperature indicator comes on and stays on, turn theengine off.If the radiator fan is working, visually check the coolant level in thereserve tank, located under the rear fender. It isn’t necessary to touchthe radiator system.

(cont’d)

226

０８／０３／０５　１６：０２：３０　３１ＨＮ８６６０　０２３２　

－

224

If the High Oil/Coolant TemperatureIndicator Lights


If the reserve tank is low or empty, don’t ride without adding coolant(page ). After adding coolant, turn the engine on and check thehigh coolant temperature indicator.If the indicator doesn’t turn off, do not ride. The engine needs repair.Transport your ATV to a Honda dealer (page ).If the temperature drops to normal, check the coolant level. If it hasgone down, add more coolant.Check for an oil leak.Check the oil level. If necessary, add the recommended oil (page )to the upper level mark. If you must leave your ATV to get oil, secureit as much as possible.Start the engine, and check that the high oil/coolant temperatureindicator goes off.

If you are able to resume riding, continue to monitor the high coolanttemperature indicator frequently.

If there is an oil leak do not ride the ATV until the leak is repaired byHonda dealer.

If there’s a mild coolant leak, you can ride for awhile, carefullywatching the indicator. Be prepared to stop and add more coolant orwater. If the leak is bad, transport your ATV to a Honda dealer(page ).

157

204

145

204

０８／０３／０５　１１：４５：２０　３１ＨＮ８６６０　０２３３　

× ×

30 A30 A15 A 2, 10 A 3

main fuse 1main fuse 2other fuses

(1)

(1) blown fuse

225

If a Fuse Blows


All of the electrical circuits on your ATV have fuses to protect themfrom damage caused by excess current flow (short circuit or overload).

If something electrical on your ATV stops working, the first thing youshould check for is a blown fuse ( ).Check all the fuses before looking elsewhere for another possible causeof the problem. Replace any blown fuses and check componentoperation.

Recommended Fuses

The main fuse and the circuit fuses are located in the batterycompartment.

1

０８／０３／０５　１１：４５：２９　３１ＨＮ８６６０　０２３４　

UNDER SEAT (4)

(2)(3)

(5)

(4) fuse box cover(5) spare main fuse

(2) main fuse 1(3) main fuse 2

226

If a Fuse Blows


Main Fuse AccessTo prevent an accidental short circuit, turn the ignition switch OFF( ) before checking or replacing the fuses.Remove the seat (page ).To access the main fuse ( ) ( ), remove the fuse box cover ( ).

Pull the main fuse out.If it is blown, install the spare main fuse ( ).

1.

2.3. 2 3 4

4.

140

5

０８／０３／０５　１１：４５：３６　３１ＨＮ８６６０　０２３５　

(7)

(6)

(7) spare fuses(6) circuit fuses

227

If a Fuse Blows


Replacing a f use with one that has a higher rating greatly increases thechance of damage to the electrical system.

Circuit Fuse AccessTo check or replace a circuit fuse ( ), pull the old fuse out of itsretaining clips.If the fuse is blown, replace it with a spare fuse ( ) of the same rating.

If you do not have a replacement fuse with the proper rating for thecircuit, install one with a lower rating.

Install the seat.Install the fuse box cover.

6

6.7.

5.

7

０８／０３／０５　１１：４５：４３　３１ＨＮ８６６０　０２３６　

228

If a Fuse Blows


If you do not have a spare fuse and you cannot ride the ATV withoutfixing the problem, take a fuse of the same rating or a lower rating fromone of the other circuits that you can do without temporarily.

If you replace a blown fuse with a spare fuse that has a lower rating,replace the fuse with the correct rating as soon as you can. Alsoremember to replace any spare fuses that were installed.

If the replacement fuse of the same rating burns out in a short time,there is probably a serious electrical problem on your ATV. Leave theblown fuse in that circuit and have your ATV checked by your Hondadealer.

０８／０３／０５　１１：４５：４７　３１ＨＮ８６６０　０２３７　

229

If You Crash


Personal safety is your first priority after an accident. If you or anyoneelse has been injured, take time to assess the severity of the injuries andwhether it is safe to continue riding. If you cannot ride safely, sendsomeone for help. Do not ride if you will risk further injury.

If you decide you are capable of riding safely, carefully inspect yourATV for damage and determine if it is safe to ride. Check the tightnessof critical nuts and bolts securing such parts as the handlebar, controllevers, brakes, and wheels.

If there is minor damage, or you are unsure about possible damage butdecide to try riding the ATV back to your base, ride slowly andcautiously.

Sometimes, crash damage is hidden or not immediately apparent. Whenyou get home, thoroughly check your ATV and correct any problemsyou find. Also, be sure to have your Honda dealer check the frame andsuspension after any serious crash.

０８／０３／０５　１１：４５：５２　３１ＨＮ８６６０　０２３８　

(1) key number

(1)

230

If You Lose Your Key


Be sure to record your key number ( ) in the Quick Reference sectionat the rear of the manual. You’ll need this number to have a duplicatekey made.

If you lose your key and aren’t carrying a duplicate, either get yourspare or have one made. If you don’t know your key number, call thedealer where you purchased your Honda ATV. They may have it listedin their records. If they don’t, transport your ATV to them or the nearestHonda dealer. The dealer will probably have to remove the ignitionswitch assembly to find the key number so they can make a key for you.

1

０８／０３／０５　１１：４５：５７　３１ＨＮ８６６０　０２３９　

231

If the Battery Is Low (or Dead)


Your ATV will operate even if the battery is low (or dead), as long asthe engine is running. If the engine is not running, it may be startedusing the recoil starter.

Jump starting is not recommended, especially if you use an automobilebattery. The greater amperage of an automobile battery when the carengine is running can damage your ATV’s electrical system.

Bump starting is also not recommended.

If you can’t charge the battery or it appears unable to hold a charge,contact your Honda dealer.

Shift the shift lever in neutral (N) position.Apply the parking brake.Turn the ignition switch to the ‘‘ON’’ ( ) position.Use the recoil starter (page ) to start the engine.

1.2.3.4. 101

０８／０３／０５　１１：４６：０３　３１ＨＮ８６６０　０２４０　

232

If a Component Fails


The brake levers or pedal, control cables, and other components can bedamaged as you ride in dense brush or over rocky terrain. Making atrailside repair depends on how serious the damage is and what tools andsupplies you have with you.

If any component of the brake system is damaged, you may be able toride carefully back to your base using the other brake components forslowing or stopping.If you damage a throttle cable or other critical component, your ATVmay be unsafe to ride. Carefully assess the damage and make anyrepairs that you can. But if there is any doubt, it’s best to beconservative and safe.

０８／０３／０５　１１：４６：０７　３１ＨＮ８６６０　０２４１　

233

Technical Information


This section contains dimensions, capacities, and other technical data,plus information on government requirements and how to break-in yourATV.

........................................................................Vehicle Identification .....................................................................................Specifications .

..........................................................................Break-in Guidelines ..................................................................Emission Control Systems .

..............................................................................Oxygenated Fuels .

234236240241245

０８／０３／０５　１１：４６：１４　３１ＨＮ８６６０　０２４２　

(1)

(2)

(2) engine number

FRONT

RIGHT SIDE

(1) VIN

234

Serial Numbers

Vehicle Identification


The VIN, engine serial number, and key number may be required whenordering replacement parts. You may record these numbers in the QuickReference section at the rear of this manual.

The VIN ( ) is stamped on the front of the frame.

The engine number ( ) is stamped on the upper side of the rearcrankcase.

1

2

０８／０３／０５　１１：４６：２０　３１ＨＮ８６６０　０２４３　

(1) color label

UNDER SEAT

((11))

235

Color Label & Code

Vehicle Identification


The color code is helpful when ordering replacement parts. You mayrecord the color and code in the Quick Reference section at the rear ofthis manual.

The color label ( ) is attached to the frame under the seat. Remove theseat (page ) to check the label.

1140

０８／０３／０５　１１：４６：２６　３１ＨＮ８６６０　０２４４　

83.2 in (2,113 mm)46.8 in (1,189 mm)47.5 in (1,207 mm)50.7 in (1,289 mm)9.2 in (234 mm)

unleaded gasoline, pump octanenumber of 86 or higher4.44 US gal (16.8 )

4.3 US qt (4.1 )

2.9 US qt (2.7 )API Service Classification SG orhigher except oils labeled as energyconserving on the circular APIservice label, SAE 10W-30, JASO T903 standard MA,Pro Honda GN4 4-stroke oil (USA &Canada) or Honda 4-stroke oil(Canada only), or an equivalentmotorcycle oil

after disassembly:

after draining:

overall lengthoverall widthoverall heightwheelbaseground clearance

fuelrecommendationfuel tank capacityengine oil capacity

engine oilrecommendation

Dimensions

Fuel & Lubricants

236

Specifications


０８／０３／０５　１１：４６：３９　３１ＨＮ８６６０　０２４５　

× ×

±

－－

(cont’d)

Pro Honda HP Coolant or anequivalent high quality ethyleneglycol antifreeze containingcorrosion protection inhibitorsspecifically recommended for usein aluminum engines

operator only

2.1 US qt (2.0 )

485 lbs (220 kg)

41.2 cu-in (675 cm )

rider, all cargo and accessories

4.02 3.25 in (102.0 82.6 mm)9.2 : 1IFR5L11 (NGK)

IFR6L11 (NGK)

1,400 50 rpm0.013 in (0.33 mm)0.006 in (0.15 mm)

0.039 0.043 in (1.00 1.10 mm)

VK16PRZ11 (DENSO)

VK20PRZ11 (DENSO)

or

or

intake:exhaust:

cooling systemrecommendation

cooling systemcapacity

passenger capacitymaximum weightcapacity

displacementbore & strokecompression ratiospark plug(standard)spark plug(high speed riding)

idle speed

valve clearance(cold)

spark plug gap

Fuel & Lubricants

Capacities

Engine Specifications

237

Specifications


０８／０３／０５　１１：４６：５６　３１ＨＮ８６６０　０２４６　

°

× ★★

× ★★

2.0002.375

1.333

2.053

3.2313.154

1.3750.9332.138shaft

1.60.08 in (2.1 mm)

AT25 10R12

AT25 8R12DUNLOP KT511

DUNLOP KT5153.6 psi (25.0 kPa)3.6 psi (25.0 kPa)

frontrear

forwardreversefrontrear

primary reduction

tire pressure,front & rear (cold)

final drivereverse

1st2nd3rd

secondary reduction

final reduction

transmission ratio

castertrailtire size, front

tire size, rear

Power Transmission

Chassis & Suspension

238

Specifications


０８／０３／０５　１１：４７：１４　３１ＨＮ８６６０　０２４７　

××

－

× ×

12 V 21/5 W 212 V 40/40 W 2

12 V 18 Ah0.36 kW/5,000 rpm

LEDLED

47 lbf·ft (64 N·m , 6.5 kgf·m)

9 lbf·ft (12 N·m , 1.2 kgf·m)

9 lbf·ft (12 N·m , 1.2 kgf·m)13 lbf·ft (18 N·m , 1.8 kgf·m)18 lbf·ft (25 N·m , 2.5 kgf·m)

15 A 2, 10 A 330 A30 A

LED

LED

LED

headlight

batterygenerator

neutral indicatorreverse indicatorhigh oil/coolanttemperature indicator

brake/tail light

wheel nuts

differential oil drainbolt

rear final gear caseoil drain bolt

othermain 2main 1

PGM-FI indicator4WD indicator

engine oil drain boltengine oil filter bolt

Lights

Electrical

Torque Specification

Fuses

239

Specifications


０８／０３／０５　１１：４７：３３　３１ＨＮ８６６０　０２４８　

240

Break-in Guidelines


Help assure your ATV’s future reliability and performance by payingextra attention to how you ride during the first operating day or 15 miles(25 km).

During this period, avoid full-throttle starts and rapid acceleration.

０８／０３／０５　１１：４７：３７　３１ＨＮ８６６０　０２４９　

(2)

(1)

(1) vehicle emission control information label

(2) vehicle emission control information label (Canada only)

241

Emission Control Systems


Exhaust Emission RequirementsThe U.S. Environmental Protection Agency (EPA), the California AirResources Board (CARB), and Environment Canada (EC) require thatyour ATV comply with applicable exhaust emissions standards duringits useful life, when operated and maintained according to theinstructions provided.

The Vehicle Emission Control Information Label ( ) is attached on theleft side of the frame.

The Vehicle Emission Control Information Label ( ) is attached on theleft rear fender below the seat.

1

2

０８／０３／０５　１１：４７：４３　３１ＨＮ８６６０　０２５０　

242

Source of Exhaust Emissions

Crankcase Emission Control System

Exhaust Emission Control System



The combustion process produces carbon monoxide (CO), oxides ofnitrogen (NOx) and hydrocarbons (HC). Control of hydrocarbons andoxides of nitrogen is very important because, under certain conditions,they react to form photochemical smog when subjected to sunlight.Carbon monoxide does not react in the same way, but it is toxic.

Honda Motor Co., Ltd. utilizes various systems to reduce carbonmonoxide, oxides of nitrogen and hydrocarbons.

The exhaust emission control system includes a PGM-FI system.No adjustment to this system should be made although periodicinspection of the components is recommended.The exhaust emission control system is separate from the crankcaseemission control system.

The engine is equipped with a closed crankcase system to preventdischarging crankcase emissions into the atmosphere. Blow-by gas isreturned to the combustion chamber through the air cleaner.

０８／０３／０５　１１：４７：４９　３１ＨＮ８６６０　０２５１　

243



Problems That May Affect ATV Exhaust EmissionsIf you are aware of any of the following symptoms, have the vehicleinspected and repaired by your Honda ATV dealer.

Symptoms:Hard starting or stalling after startingRough idleMisfiring or backfiring during accelerationAfter-burning (backfiring)Poor performance (driveability) and poor fuel economy

Federal regulations prohibit removing or disabling a device or elementof design that may affect your engine’s emission performance unlessyour ATV will be used exclusively in competition. If you modify yourengine for use in sanctioned competition events, you must deface ordestroy the emission control information label.

1.2.3.4.5.

０８／０３／０５　１１：４７：５４　３１ＨＮ８６６０　０２５２　

244


Noise Emission Control System

Fuel Permeation Emission Control System


TAMPERING WITH THE NOISE CONTROL SYSTEM ISPROHIBITED:State laws prohibit, or Canadian provincial laws may prohibit, thefollowing acts or the causing thereof: ( ) The removal or renderinginoperative by any person, other than for purposes of maintenance,repair or replacement, of any device or element of design incorporatedinto any new vehicle for the purpose of noise control prior to its sale ordelivery to the ultimate purchaser or while it is in use; or ( ) the use ofthe vehicle after such device or element of design has been removed orrendered inoperative by any person.

AMONG THOSE ACTS PRESUMED TO CONSTITUTETAMPERING ARE THE FOLLOWING ACTS:

Removal of, or puncturing the muffler, baffles, header pipes or anyother component which conducts exhaust gases.Removal of, or puncturing of any part of the intake system.Lack of proper maintenance.Replacing any moving parts of the vehicle, or parts of the exhaust orintake system, with parts other than those specified by themanufacturer.

This vehicle complies with the Fuel Permeation Emission Controlregulations of the U.S. Environmental Protection Agency (EPA), theCalifornia Air Resources Board (CARB), and Environment Canada(EC).The fuel tank, fuel hoses, and fuel vapor charge hoses used on thisvehicle incorporate fuel permeation control technologies.Tampering with the fuel tank, fuel hoses, or fuel vapor charge hoses toreduce or defeat the effectiveness of the fuel permeation technologies isprohibited by federal regulations.

1.

2.3.4.

1

2

０８／０３／０５　１１：４８：０１　３１ＨＮ８６６０　０２５３　

245

Oxygenated Fuels


Some conventional gasolines are being blended with alcohol or an ethercompound. These gasolines are collectively referred to as oxygenatedfuels. To meet clean air standards, some areas of the United States andCanada use oxygenated fuels to help reduce emissions.If you use an oxygenated fuel, be sure it is unleaded and meets theminimum octane rating requirement.Before using an oxygenated fuel, try to confirm the fuel’s contents.Some states/provinces require this information to be posted on the pump.

The following are the EPA-approved percentages of oxygenates:

ETHANOL (ethyl or grain alcohol) 10% by volumeYou may use gasoline containing up to 10% ethanol by volume.Gasoline containing ethanol may be marketed under the name‘‘Gasohol’’.

MTBE (Methyl Tertiary Butyl Ether) 15% by VolumeYou may use gasoline containing up to 15% MTBE by volume.

METHANOL (methyl or wood alcohol) 5% by VolumeYou may use gasoline containing methanol containing up to 5%methanol by volume as long as it also contains cosolvents and corrosioninhibitors to protect the fuel system. Gasoline containing more than 5%methanol by volume may cause starting and/or performance problems. Itmay also damage metal, rubber, and plastic parts of your fuel system.

０８／０３／０５　１１：４８：０６　３１ＨＮ８６６０　０２５４　

246

Oxygenated Fuels


Oxygenated f uels can damage paint and plastic. Damage caused byspilled f uel is not covered by warranty.

If you notice any undesirable operating symptoms, try another servicestation or switch to another brand of gasoline.

Fuel system damage or performance problems resulting from the use ofan oxygenated fuel containing more than the percentages of oxygenatesmentioned above are not covered under warranty.

Oxygenated fuels can damage paint and plastic. Be careful not to spillfuel when filling the fuel tank. Wipe up any spills immediately.

０８／０３／０５　１１：４８：１１　３１ＨＮ８６６０　０２５５　

247

Consumer Information


This section contains information on your warranty and how to get anofficial Honda service manual.

................................................The Honda Rider’s Club (USA only) ............................................................................Your Honda Dealer .

.............................................................................Contacting Honda .

..........................................................................Authorized Manuals ............................................................................Warranty Coverage .

...............................................................................Warranty Service .

248251252253254255

０８／０３／０５　１１：４８：１７　３１ＨＮ８６６０　０２５６　

＊

＊Prices are subject to change without notice and without incurring obligation.

2009 TRX680FA/FGA RINCONService Manual

2009 TRX680FA/FGA RINCONOwner’s Manual

Common Service Manual

61HN853

61CM00231HN8660

$60.00

$48.00$16.00

Publication Item No. Description Price Each

248

Authorized Manuals


The Service Manual used by your authorized Honda dealer is availablefrom Helm, Inc. (USA only, Canada: See your Honda dealer to orderauthorized manuals.)

Also available but not necessary to service your model is the HondaCommon Service Manual which explains theory of operation and basicservice information for various systems common to all Hondamotorcycles, motor scooters and ATVs.

These Honda manuals are written for the professional technician, butmost mechanically capable owners should find them easy to use if theyhave the proper tools and observe proper safety standards. SpecialHonda tools are necessary for some procedures.

０８／０３／０５　１１：４８：２５　３１ＨＮ８６６０　０２５７　

－－

＊

＊

Prices are subject to change without notice and

without incurring obligation.

Orders are mailed within 10 days. Please allow

adequate time for delivery. $3.75

Publication

Item No.

Purchaser’s Sales Tax

Mich. add 6 %

Calif. add 7.25 %

Handling Charge

Grand Total

Sub Total

Item Description Qty. Price

Each

Total

Price

249

Order On-Line: www.helminc.com

Order Toll Free: 1-888-CYCLE93

OR


(NOTE: For Credit Card Orders Only)

(1-888-292-5393)

Monday Friday 8:00 AM 6:00 PM EST

By completing this form you can order the materials desired. You canpay by check or money order, or charge to your credit card. Mail toHelm, Inc. at the address shown on the back of this order form (USAonly).

Canada: See your Honda dealer to order authorized manuals.

０８／０３／０５　１１：４８：３４　３１ＨＮ８６６０　０２５８　

－

P. O. BOX 07280, DETROIT, MICHIGAN 48207

SHIP

TO

PAYMENT

NOTE: Dealers and Companies please provide dealer or company name, and also the name of the person to

whose attention the shipment should be sent.

Customer Name

Attention

Street address/P. O. BOX Apartment Number

City State Zip Code

Daytime Telephone Number

Check or money order enclosed payable to Helm Inc. U. S. funds only. Do not send cash.

Check here if your billing address is different from the shipping address shown above.

VISA DiscoverMasterCard

Expiration: Mo. Yr.

Customer Signature Date

These Publications cannot be returned for credit without receiving advance authorization within 14 days of delivery. For

returns, a restocking fee may be applied against the original order.

Account Number

Security Code

( )

HELM

250 Consumer Information

０８／０３／０５　１１：４８：４８　３１ＨＮ８６６０　０２５９　

251

Warranty Coverage


Your new Honda is covered by these warranties:

There are responsibilities, restrictions, and exclusions which apply tothese warranties. Please read the Warranties Booklet given to you byyour Honda dealer at the time of purchase. Be sure to keep your Hondaowner’s card with your Warranties Booklet (USA only).

It is important to realize that your warranty applies to defects in materialor workmanship of your Honda. Your warranty coverage does not applyto normal wear or deterioration associated with using the ATV.

Your warranty coverage will not be voided if you choose to performyour own maintenance. However, you should have the proper tools andservice information, and be mechanically qualified. Failures that occurdue directly to improper maintenance are not covered.

Almost all of your warranty coverage can be extended through theHonda Protection Plan (USA only). For more information, see yourHonda dealer.

TRX Limited WarrantyEmission Control System Warranty

０８／０３／０５　１１：４８：５５　３１ＨＮ８６６０　０２６０　

252

Warranty Service


Please remember that recommended maintenance interval servicing isnot included in your warranty coverage. Additionally, your warrantydoes not apply to the normal wear of items (such as brakes, tires, etc.).

If you believe you have a problem with your ATV, call the servicedepartment of your Honda dealer. Make an appointment for aninspection and diagnosis. Remember, as the owner of the ATV, you willbe asked to authorize that inspection. Your dealer will give you theresults of the inspection. If the problem is covered under warranty, yourdealer will perform the warranty repairs for you.

If you have questions about warranty coverage or the nature of therepair, it is best to talk to the Service Manager of your Honda dealer.

Sometimes, in spite of the best intentions of all concerned, amisunderstanding may occur. If you aren’t satisfied with your dealer’shandling of the situation, we suggest you discuss your problem with theappropriate member of the dealership’s management team. If theproblem has already been reviewed with the Service Manager, PartsManager, Sales Manager, etc., contact the Owner of the dealership ortheir designated representative.

０８／０３／０５　１１：４９：００　３１ＨＮ８６６０　０２６１　

253

Contacting Honda


Your owner’s manual was written to cover most of the questions youmight ask about your Honda. Any questions not answered in the owner’smanual can be answered by your Honda dealer. If your dealer doesn’thave the answer right away, they will get it for you.

If you have a difference of opinion with your dealer, please rememberthat each dealership is independently owned and operated. That’s whyit’s important to work to resolve any differences at the dealership level.

If you wish to comment on your experiences with your Honda or withyour dealer, please send your comments to the following address (USAonly):Motorcycle Division, American Honda Motor Co., Inc., P.O. Box 2200,Torrance, CA 90509-2200, mailstop: 100-4C-7B, telephone: (866) 784-1870.

Canada: Refer to the Warranties Booklet that was supplied with yourvehicle.

Please include the following information in your letter:name, address, and telephone numberproduct model, year, and VINdate of purchasedealer name and address

We will likely ask your Honda dealer to respond, or possiblyacknowledge your comments directly.

０８／０３／０５　１１：４９：０６　３１ＨＮ８６６０　０２６２　

254

Your Honda Dealer


Once you purchase your new Honda, get familiar with the organizationof your Honda dealer so you can utilize the full range of servicesavailable.

The service department is there to perform regular maintenance andunexpected repairs. It has the latest available service information fromHonda. The service department will also handle warranty inspectionsand repairs.

The parts department offers Honda Genuine Parts, Pro Honda products,Honda Genuine Accessories (USA only), and Honda accessories andproducts (Canada only). The same quality that went into your Honda canbe found in Honda Genuine replacement parts. You’ll also findcomparable quality in the accessories and products available from theparts department.

The sales department offers the Honda Protection Plan to extend almostall of your warranty coverage (USA only).

Your Honda dealer can inform you about competition and other ridingevents in your area. You’ll also find that your dealer is a source ofinformation about American Honda’s Rider Education Centers and theHonda Rider’s Club of America (USA only).

We’re sure you’ll be as pleased with the service your Honda dealercontinues to provide after the sale as you are with the quality anddependability of your Honda.

０８／０３／０５　１１：４９：１２　３１ＨＮ８６６０　０２６３　

255

The Honda Rider’s Club (USA only)


www.hrca.honda.com.

You may be eligible for a Honda Rider’s Club of America (HRCA)membership with the purchase of your new Honda. You can log on tothe HRCA Clubhouse website for details at

０８／０３／０５　１１：４９：１５　３１ＨＮ８６６０　０２６４　

256

Table of Contents

Table of Contents

......................................................................................ATV SAFETY . 1

.......................................................INSTRUMENTS & CONTROLS . 9

The following presents the contents of each section of your owner’smanual.

...............................................................Important Safety Information ..........................................................................................Safety Labels .

..........................................................Operation Component Locations .............................................................................Indicators & Displays .

......................................................................Multi-function Display .........................................................................Drive Mode Indicator .......................................................................Gear Position Indicator .

.........................................................................Oil Change Indicator ............................................................................................Odometer .

..............................................................................Controls & Features .........................................................................................Fuel Gauge .

.....................................................................................Digital Clock ..........................................................................................Hourmeter .

...........................................................................................Tripmeter .

..................................................................................Ignition Switch .........................................................................................Shift Lever .

.................................................................Drive Mode Select Switch .

.................................................................2WD/4WD Select Switch ........................................................................................Start Button .

...........................................................................Engine Stop Switch ................................................................................Headlight Switch .

.................................................................Headlight Dimmer Switch ......................................................................................Recoil Starter ....................................................................................Throttle Lever .

................................................................................Gearshift Switch .

25

1114192021222323252629303031323334343535363738

０８／０３／０５　１１：４９：３２　３１ＨＮ８６６０　０２６５　

257

Table of Contents

Table of Contents

..............................................GPScape System (TRX680FGA only) . 45

.............................................................................Front Brake Lever ...............................................................................Rear Brake Lever .

...............................................................................Rear Brake Pedal .....................................................................................Parking Brake .

..............................................................................Flag Pole Bracket .

..............................................................................Accessory Socket .

...........................................................................................Introduction ................................................................Important Safety Information .

................................................................................System Limitations ......................................................................................System Start-up .

.......................................................................................Position Fix ...........................................System Failure to Display a Position Fix .

.......................................................................................Satellite Status ..............................................................................................GPS Mode .

............................................................................GPS Mode Display ................................................................Waypoint Number Display .

.........................................................Direction to Waypoint Display .........................................................................Distance to Waypoint .

.................................................................Basic Waypoint Selection ...........................................................Advanced Waypoint Selection .

....................Determining the Coordinates of Your Current Position ..................................................................Compass Direction Indicator .................................................................Automatic Clock Adjustment .

393939404142

4649505151525456585960626365697072

０８／０３／０５　１１：４９：４８　３１ＨＮ８６６０　０２６６　

258

Table of Contents

Table of Contents

.............................................................................BEFORE RIDING . 73.......................................................................Are You Ready to Ride? .

.............................................................................Protective Apparel ....................................................................................Rider Training .

.......................................................................Age Recommendation ....................................................................................No Passengers .

.........................................................................No Alcohol or Drugs .................................................................Is Your ATV Ready to Ride? .

............................................................................Pre-ride Inspection ......................................................................Load Limits & Guidelines .

.............................................................................................Loading .

...........................................................................Loading Guidelines .................................................................Accessories & Modifications .

........................................................................................Accessories .....................................................................................Modifications .

..........................................................Cargo and Trailer Information .

747476777778797983838486878788

０８／０３／０５　１１：５０：００　３１ＨＮ８６６０　０２６７　

259Table of Contents

Table of Contents

....................................................BASIC OPERATION & RIDING . 89........................................................................Safe Riding Precautions .

............................................................................Off-road Use Only ......................................................Keep Hands and Feet on Controls .

....................................................................................Control Speed .........................................Use Care on Unfamiliar or Rough Terrain .

......................................................................Do Not Perform Stunts .............................................................Starting & Stopping the Engine .

........................................................................................Preparation ..............................................................................Starting Procedure .

..............................................................................Riding in Reverse ....................................................................................Shifting Gears .

................................................................Using the Recoil Starter .

................................................................How to Stop the Engine .

.................................................................................Flooded Engine .....................................Bank Angle Sensor Ignition Cut-off System .

...................................................................................Stalled Engine .

(cont’d)

919192939495969697989899

100101102108

０８／０３／０５　１１：５０：１２　３１ＨＮ８６６０　０２６８　

260 Table of Contents

Table of Contents

..............................................................................................Braking ..............................................................................Riding Your ATV .

................................................................................Making Turns ........................................................................Skidding or Sliding .

.............................................................................Riding Up Hills .........................................................................Riding Down Hills .

.........................................Crossing or Turning on Hills or Slopes ...................................................................Riding Over Obstacles .

..............................................................................................Parking ...................................................................Riding Through Water .

110112112114115119120122123124

０８／０３／０５　１１：５０：２０　３１ＨＮ８６６０　０２６９　

261

.........................................................SERVICING YOUR HONDA . 125

Table of Contents

Table of Contents

Service Preparations

Service Procedures

Bef ore You Service Your Honda

Fluids & Filters

Engine

.......................................................The Importance of Maintenance ............................................................................Maintenance Safety .

......................................................................Maintenance Schedule ...........................................................................Maintenance Record .

..................................................Maintenance Component Locations ..............................................................................................Tool Kit .

...................................................................Owner’s Manual Storage .....................................................................................Seat Removal .

...................................................................................................Fuel .............................................................................Engine Oil & Filter .

....................................................................................Gear Case Oil ...................................................................................Differential Oil .

..............................................................................................Coolant .........................................................................................Air Cleaner .

..............................................................................................Throttle .

........................................................Important Safety Precautions .

.........................................................................................Spark Plug .................................................................................................Valves .

...................................................................................Spark Arrester .

(cont’d)

127128129130134

135138139140

141144152154156161

166168171172

０８／０３／０５　１１：５０：３６　３１ＨＮ８６６０　０２７０　

262

...................................................................................................TIPS . 201

...................................TAKING CARE OF THE UNEXPECTED . 211

Table of Contents

Table of Contents

Chassis................................................................................................Brakes .

..............................................................Engine Guard & Skid Plates ................................................................................Driveshaft Boots .

Electrical...............................................................................................Battery .

...............................................................................Appearance Care .

..................................................................................................Tires .

.............................................................What to Take on the Trail ..................................................................Transporting Your Honda .

..........................................................................Storing Your Honda .....................................................................You & the Environment .

..................................................What to Take to the Riding Area .

.....................If the High Oil/Coolant Temperature Indicator Lights ..................................................................................If a Fuse Blows .

......................................................................................If You Crash .......................................................................If You Lose Your Key .

.........................................................If the Battery Is Low (or Dead) ..........................................................................If a Component Fails .

............................................................................General Guidelines ..................................................If Your Engine Quits or Won’t Start .

..............................If the Transmission Is Not Functioning Properly ......................................................................If You Have a Flat Tire .

..........................................................................Preparing for a Ride .

174182189190

191

196

202202203204206210

212215217219223225229230231232

０８／０３／０５　１１：５０：５３　３１ＨＮ８６６０　０２７１　

263

Table of Contents

Table of Contents

.....................................................TECHNICAL INFORMATION . 233

......................................................CONSUMER INFORMATION . 247

.................................................................TABLE OF CONTENTS . 256

...............................................................................................INDEX . 264

QUICK REFERENCE

........................................................................Vehicle Identification .....................................................................................Specifications .

..........................................................................Break-in Guidelines ..................................................................Emission Control Systems .

..............................................................................Oxygenated Fuels .

..........................................................................Authorized Manuals ............................................................................Warranty Coverage .

...............................................................................Warranty Service ..............................................................................Contacting Honda ............................................................................Your Honda Dealer .

................................................The Honda Rider’s Club (USA only) .

234236240241245

248251252253254255

０８／０３／０５　１１：５１：０２　３１ＨＮ８６６０　０２７２　

264

Index

Index

A

B

............................................................................................accessories . 87...................................................................................accessory socket . 42

............................................................................age recommendation . 77air cleaner,

................................................................................................filter . 161..........................................................................housing drain tube . 165

air pressure,..............................................................................................gauge . 139

..................................................................................................tire . 183..............................................................American Honda, contacting . 253

apparel,..........................................................................................protective . 74

..................................................................................appearance care . 196.............................................................................authorized manuals . 248

...........................................Bank angle sensor ignition cut-off system . 98................................................................................................Battery . 191

Brakes,..............................................................................................cables . 180

................................................................................................fluid . 174...............................................................................front brake lever . 39

.........................................................................................pad wear . 177.............................................................................................parking . 40

.................................................................................rear brake lever . 39................................................................rear brake lever freeplay . 179

................................................................................rear brake pedal . 39

０８／０３／０５　１１：５１：０６　３１ＨＮ８６６０　０２７３　

265

Index

Index

C

...............................................................................................braking . 110.............................................................................break-in guidelines . 240

button,..................................................................................................ADJ . 26

........................................................digital clock / hourmeter select . 26.........................................................................................GPS / WP . 57........................................................................................hour select . 26

..........................................................................................minus . 27, 59.....................................................................................minute select . 26

...............................................................odometer / tripmeter select . 23.............................................................................................plus . 27, 59

.............................................................................................RESET . 24

......................................................................................capacity, fuel . 142.................................................................................care, appearance . 196

cargo,.................................................Loading and operational guidelines . 86

.....................................................................................Weight limit . 85......................................................................................climbing hills . 115

...........................................................................................color label . 235compartment,

..............................................................................owner’s manual . 139............................................................................................tool kit . 138

..................................................................................component fails . 232........................................................................consumer information . 247

........................................................................................crash, if you . 229..................................................crossing or turning on hills or slopes . 120

.................................................................................customer service . 253

０８／０３／０５　１１：５１：１１　３１ＨＮ８６６０　０２７４　

266

Index

Index

D

E

....................................................................................differential oil . 154..........................................................................................digital clock . 26

.................................................digital clock / hourmeter select button . 25......................................................................dimmer switch,headlight . 35

...............................................................................................dipstick . 147.........................................................................display, multi-function . 19

..................................................................................driveshaft boots . 190............................................................................drive mode indicator . 20

......................................................................drive mode select switch . 32

.....................................................................emission control system . 241engine

.............................................................................................flooded . 98..............................................................................................guard . 189

...........................................................................................number . 234...................................................................................................oil . 144

...........................................................................................pinging . 141..............................................................................................starting . 96

........................................................................................stop switch . 34..........................................................................................stopping . 100

......................................................................................won’t start . 215.......................................................................................environment . 210

０８／０３／０５　１１：５１：１５　３１ＨＮ８６６０　０２７５　

267

Index

Index

F

G

...................................................................................gap, spark plug . 169...............................................................................................gasohol . 245..............................................................................................gasoline . 141

........................................................................................gear case oil . 152.......................................................................................gear shifting . 102

................................................................................GPS mode display . 58..............................................................................GPS/WP button . 18, 57

...............................................................................final gear case oil . 152...................................................................................flag pole bracket . 41

................................................................................................flat tire . 219......................................................................................flooded engine . 98

fuel,............................................................................................fill cap . 142

................................................................................................gauge . 29.....................................................................................oxygenated . 245

.............................................................................recommendation . 141..................................................................................tank capacity . 142

...................................................................................................fuses . 225

０８／０３／０５　１１：５１：２０　３１ＨＮ８６６０　０２７６　

268

Index

Index

H

......................................................................headlight dimmer switch . 35...................................................................................headlight switch . 35

hills,...........................................................crossing or turning on slops . 120

............................................................................riding down hills . 119.................................................................................riding up hills . 115

.............................................................................stopping on hills . 117Honda,

.......................................................................................contacting . 253..............................................................................................dealer . 254

...................................................................................Rider’s Club . 255........................................................................Honda service manual . 248

.............................................................................................hourmeter . 25.................................................................................hour select button . 25

０８／０３／０５　１１：５１：２４　３１ＨＮ８６６０　０２７７　

269

Index

Index

I

K

.........................................................................identification, vehicle . 234......................................................................................ignition switch . 30

indicators........................................................................drive mode indicator . 20......................................................................gear position indicator . 21

.............................................high oil/coolant temperature indicator . 16...............................................................................neutral indicator . 17

..........................................................................oil change indicator . 22.............................................................................PGM-FI indicator . 18

...............................................................................reverse indicator . 16............................................................................4WD indicator . 16, 33

...............................................................................inspection, pre-ride . 79

..............................................................................................key, lost . 230...............................................................................................kit, tool . 138

０８／０３／０５　１１：５１：２８　３１ＨＮ８６６０　０２７８　

270

Index

Index

L

M

maintenance,......................................................................................importance . 127.....................................................................................precautions . 129

.............................................................................................record . 134..............................................................................................safety . 128

..........................................................................................schedule . 130...................................................................................manual, service . 248

.........................................................................maximum weight limit . 85...................................................................................minus button . 27, 65........................................................................................modifications . 88

..........................................................................multi-function display . 19

...........................................................................................labels, safety . 5...........................................................................................lamp check . 15.........................................................................................limit, weight . 85

................................................................................loading guidelines . 86...............................................................................................longitude . 47

lubrication................................................................................differential oil . 154

........................................................................................engine oil . 144....................................................................................gear case oil . 152

０８／０３／０５　１１：５１：３３　３１ＨＮ８６６０　０２７９　

271

Index

Index

N

O

...................................................................................neutral indicator . 17..........................................................noise emission control systems . 244

...................................................................................numbers, serial . 234

.........................................................................obstacles, riding over . 122...............................................................................................odometer . 23

..........................................................odometer/tripmeter select button . 23oil,

......................................................................................differential . 154.............................................................................................engine . 144

.........................................................................................gear case . 152.............................................oil/coolant temperature indicator . 14, 223

......................................................................owner’s manual storage . 139................................................................................oxygenated fuels . 245

０８／０３／０５　１１：５１：３７　３１ＨＮ８６６０　０２８０　

272

Index

Index

P

R

........................................................................rear final gear case oil . 152..........................................................................................recoil starter . 36......................................................................................removal, seat . 140

reverse,...........................................................................gear, shifting into . 108

...........................................................................................indicator . 16..........................................................................................riding in . 108

.........................................................................................rider training . 76...........................................................................Rider’s Club, Honda . 255

...............................................................................................parking . 124..........................................................................passenger, no carrying . 77........................................................................pavement, no reding on . 91

...................................................................................pinging, engine . 141..........................................................................................plug, spark . 168......................................................................................plus button . 27, 65

................................................................................pre-ride inspection . 79.........................................................................problems, unexpected . 211

.................................................................................protective apparel . 74

０８／０３／０５　１１：５１：４２　３１ＨＮ８６６０　０２８１　

273

Index

Index

S

(cont’d)

safety,.....................................................................important precautions . 129

..................................................................................................labels . 5.............................................................................riding precautions . 91

........................................................................schedule, maintenance . 132.......................................................................................seat removal . 140

....................................................................................serial numbers . 234service,

.........................................................................................customer . 253..........................................................................................manuals . 248.........................................................................................warranty . 252

riding,................................................................................basic operations . 89

.............................................................................................clothing . 74.................................................................................over obstacles . 122

.......................................................................................precautions . 91..................................................................................preparing for . 202

..................................................................................................safety . 2.............................................................................safety precautions . 91

.................................................................................through water . 123

０８／０３／０５　１１：５１：４７　３１ＨＮ８６６０　０２８２　

274

Index

Index

......................................................................................shifting gears . 102

........................................................................................shifting lever . 31............................................................................................skid plate . 189

..............................................................................skidding or sliding . 114......................................................................................spark arrester . 172

........................................................................................spark knock . 141...........................................................................................spark plug . 168

......................................................................................specifications . 236.........................................................................................speedometer . 17

..................................................................................stalling on a hill . 117............................................................................................start button . 34

starting,...............................................................................................engine . 96

...............................................................................troubleshooting . 215...............................................................................stop switch, engine . 34

..................................................................................stopping engine . 100storage,

...............................................................................................ATV . 206..............................................................................owner’s manual . 139

switch,...........................................................................................headlight . 35

.............................................................................headlight dimmer . 35.............................................................................................ignition . 30

.............................................................................2WD/4WD select . 33

０８／０３／０５　１１：５１：５１　３１ＨＮ８６６０　０２８３　

275

Index

Index

T

V

...................................................................................valve clearance . 171.........................................................vehicle identification no. (VIN) . 234

throttle...............................................................................................cable . 166

..........................................................................................lever . 37, 166tires,

.....................................................................................air pressure . 183..................................................................................................flat . 219

.........................................................................................replacing . 188

.........................................................................................repairing . 187............................................................................thread conditions . 185

................................................................................................tool kit . 138trailer towing

......................................................................operational guidelines . 86.....................................................................................weight limits . 85

........................................................................................training, rider . 76.......................................................................transporting your ATV . 204

...............................................................................................tripmeter . 23............................................................................trouble, unexpected . 213

.....................................................................troubleshooting, starting . 215turning,

.............................................................................on hills or slopes . 120...............................................................................on level ground . 112

０８／０３／０５　１１：５１：５６　３１ＨＮ８６６０　０２８４　

276

Index

Index

W

........................................................................................warning labels . 5warranty,

.........................................................................................coverage . 251

.........................................................................................extended . 251............................................................................................service . 252

.............................................................................washing your ATV . 197water,

.................................................................................riding through . 123..........................................................................................weight limit . 85

.....................................................................................wheel removal .221

０８／０３／０５　１１：５２：００　３１ＨＮ８６６０　０２８５　

277Memo

０８／０３／０５　１１：５２：０２　３１ＨＮ８６６０　０２８６　

278 Memo

０８／０３／０５　１１：５２：０５　３１ＨＮ８６６０　０２８７　

279Memo

０８／０３／０５　１１：５２：０７　３１ＨＮ８６６０　０２８８　

How To Avoid Costly Repairs

Quick Reference

Quick Reference

The following is a brief, but important collection of information youneed to know about your Honda. You’ll also find space to recordimportant notes.

The engine of your Honda can be the most expensive component torepair. Proper maintenance, especially the use of the recommendedfluids and filters, prevents premature wear and damage.

Frequent causes of costly repairs are:Engine oil –– insufficient quantity, improper oil.

Record important information on the following page:

Air cleaner –– dirty, leaking because of improper installation(poor seal).

０８／０３／０５　１１：５２：１３　３１ＨＮ８６６０　０２８９　

Quick Reference

Quick Reference

Engine No.VINIgnition Key No.Color LabelOwner’s Name

AddressCity/StatePhone

Dealer’s NameAddressCity/StatePhoneService Mgr.

０８／０３／０５　１１：５２：１６　３１ＨＮ８６６０　０２９０　

4.44 US gal (16.8 )

485 lbs (220 kg)

Quick Reference

Quick Reference

ScheduledMaintenancePre-ride Inspection

Initial: 100 miles (150 km)Regular: every 600 miles (1,000 km)Check the following items each timebefore you ride (page ): engine oil,radiator coolant, fuel, tires, driveshaftboots, nuts & bolts, underbody & exhaustsystem, air cleaner housing drain tube,leaks, loose parts, cables, lights, throttle,brakes, switches, steering.unleaded gasoline, pump octane number86 or higher

Fuel/Capacity

Engine Oil API Service Classification SG or higherexcept oils labeled as energy conservingon the circular API service label,SAE 10W-30, JASO T 903 standard MA,Pro Honda GN4 4-stroke oil or equivalent

Maximum WeightCapacity rider, all cargo and accessories

79

０８／０３／０５　１１：５２：２５　３１ＨＮ８６６０　０２９１　

× ★★

× ★★

× ×

AT25 8R12

AT25 10R12DUNLOP KT511

DUNLOP KT515



30 A30 A15 A 2, 10 A 3

3.6 psi (25.0 kPa)3.6 psi (25.0 kPa)

orstandard:

or

Front:Rear:

high speed riding:

Front:

Rear:

main 1:main 2:others:

Quick Reference

Quick Reference

Tires

Tire Pressure (cold)

Spark Plugs

Coolant ethylene glycol antifreeze (silicate-free)for aluminum engines in 50/50 solutionwith Pro Honda HP Coolant or anequivalent distilled water

Fuses

０８／０３／０５　１１：５２：３６　３１ＨＮ８６６０　０２９２　

－－

－－－－

－－

－－

－

－

Quick Reference

Quick Reference

These symbols are used in Controls & Features section:SYMBOL COMPONENT SEE PAGE

ON ignition switchOFF ignition switch

2WD/4WD select switch

START buttonRUN engine stop switchOFF engine stop switch

ON headlight switchOFF headlight switch

HI headlight dimmer switchLO headlight dimmer switch

upshift switch gearshift switchdownshift switch gearshift switch

lock lever parking brake

30303333

34343435353535383840

4WD indicator lights whenthe 4WD mode

０８／０３／０５　１１：５２：５２　３１ＨＮ８６６０　０２９３　

2009 Honda TRX680FA/FGA FOURTRAX RINCON/with GPScape … · FOURTRAX RINCON/with GPScape OWNER’S...

Documents

Transcript of 2009 Honda TRX680FA/FGA FOURTRAX RINCON/with GPScape … · FOURTRAX RINCON/with GPScape OWNER’S...