2007 Chevrolet Corvette Navigation System M...To set the region, do the following: 1. Press the...

Overview ........................................................ 1Overview .................................................. 4

Features and Controls ................................ 17Features and Controls ............................ 18

Navigation Audio System ............................ 81Navigation Audio System ........................ 82

Voice Recognition ..................................... 107Voice Recognition ................................. 108

Index .......................................................... 119

2007 Chevrolet Corvette Navigation System M

1

GENERAL MOTORS, GM, the GM Emblem,CHEVROLET, the CHEVROLET Emblem,the name CORVETTE, and the CORVETTEEmblems are registered trademarks of GeneralMotors Corporation.

The information in this manual supplements theowner manual. This manual includes the latestinformation available at the time it was printed. Wereserve the right to make changes in the productafter that time without notice. For vehicles first soldin Canada, substitute the name General Motorsof Canada Limited for Chevrolet Motor Divisionwhenever it appears in this manual.

Keep this manual with the owner manual in thevehicle, so it will be there if it is needed. Ifthe vehicle is sold, leave this manual in thevehicle.

Canadian OwnersFor Canadian owners that would like to obtain aFrench language manual, see “Canadian Owners”in the Index of your vehicle’s owner manual.

Litho in U.S.A.Part No. 15838252 A First Printing ©2006 General Motors Corporation. All Rights Reserved.

2

Overview ......................................................... 4Navigation System Overview ......................... 4

Getting Started .............................................. 5Cleaning the Display ................................... 15

Section 1 Overview

3

OverviewNavigation System Overview

4

A. g (Voice Recognition) Key. See “Hard Keys”under Using the Navigation System onpage 18 for more information.

B. SRCE (Source) Key. See “Hard Keys” underUsing the Navigation System on page 18for more information.

C. NAV (Navigation) Key. See “Hard Keys” underUsing the Navigation System on page 18for more information.

D. ez (Audio/Screen Adjust) Key. See “HardKeys” under Using the Navigation Systemon page 18 for more information.

E. QO SEEK R (Seek/Tune) Key. See “HardKeys” under Using the Navigation Systemon page 18 for more information.

F. Power Volume Knob. See “Hard Keys” underUsing the Navigation System on page 18for more information.

G. X DVD (DVD Map Database Eject) Key. See“Installing the Map DVD” under Maps onpage 67 for more information.

H. XB (CD Eject) Key. See “CD Player onpage 95 for more information.

I. CD SlotJ. DVD Map Database SlotK. Navigation System Screen

L. X (Open/Close Faceplate) Key. See “HardKeys” under Using the Navigation Systemon page 18 for more information.

Getting StartedBefore you begin to operate the navigationsystem, read this manual thoroughly to becomefamiliar with it and to understand how thesystem works.

Keeping your mind on the drive is important forsafe driving. See “Defensive Driving” in the Indexof your vehicle’s owner manual for moreinformation. Get familiar with your vehicle’snavigation system so you can use it with lesseffort and take full advantage of its features. Yournavigation system includes not only navigation,but also audio functions.

5

While your vehicle is parked:

• Familiarize yourself with all of its controls:hard keys on the faceplate and touch-sensitivescreen buttons.

• Familiarize yourself with its operation.

• Set up your audio by presetting your favoritestations, setting the tone, and adjusting thespeakers. Then, when driving conditionspermit, you can tune to your favorite stationsusing the presets and steering wheelcontrols (if equipped).

• Set up the navigation features that can onlybe done before you begin driving, such asentering an address or a preset destination.

Entering a destination or alphanumeric textrequires many steps, so you can only performthese operations when the vehicle is in PARK (P).You will notice that touch-sensitive screenbuttons leading to the alphanumeric keyboard aredimmed out while driving.

Other functions may also be locked out whiledriving and they too will appear grayed out on thescreen — but all functions are available whenparked. Some functions can be performed whiledriving, as long as you can do so without divertingtoo much of your attention from your driving.

{CAUTION:

This system provides you with a far greateraccess to audio stations and song listings.Giving extended attention to entertainmenttasks while driving can cause a crash andyou or others can be injured or killed.Always keep your eyes on the road andyour mind on the drive — avoid engagingin extended searching while driving.

6

{CAUTION:

Looking at the moving map on thenavigation screen frequently or for toolong while driving can cause a crash andyou or others can be injured or killed.Keep your eyes and mind on the road andavoid looking too long or too often at themoving map on the navigation screen.Use the voice guidance directionswhenever possible.

The navigation system allows you to do thefollowing:

• Plan a route with provided turn-by-turn routeand map guidance with voice prompts.

• Select a destination using various methodsand choices.

• Receive broadcast announcements on trafficand emergency alert communications.

The information in the system may not always becomplete. Road conditions such as prohibitedturns, detours, and construction zones, changefrequently. It is important to consider whether youcan follow the directions given by the systemfor the current conditions.

Each time you enter the navigation system, theCAUTION screen will display. Touch Agreeto proceed into the system. For information onchanging the language, see “Driver InformationCenter (DIC)” in the Index of your vehicle’s ownermanual.

7

When getting started, you may set the navigationsystem to your preference using various options.You will also need to know how to perform variousfunctions to begin route guidance. Referencethe following topics for further information:

Setting Radio Station PresetsTo set preset radio stations, do the following:

1. Press the power/volume knob to turnthe system on.

2. Press the SRCE hard key and select thedesired band (AM, FM1, FM2, XM1, orXM2 (if equipped)).

3. Use the TUNE/SEEK arrows to tune to thedesired station.

4. Press and hold one of the six preset screenbuttons, at the bottom of the screen, until youhear a beep or see the station displayedon the selected preset button.

5. Repeat the steps for each preset.

See “Preset Station Menu” under Navigation AudioSystem on page 82 for more information.

Setting the TimeTo set the time, do the following:

1. Press the power/volume knob to turn thesystem on.

2. Press and hold the time display in the upperright corner of any screen.

3. Select the 12H or 24H screen button todisplay the time in standard or military time.

4. Press and hold the Hour and Min. (minute)arrow buttons to increase or to decreasethe time.

5. Select the appropriate time zone screenbutton.

6. Select the Daylight Saving Time screenbutton, if necessary.

The radio will use the GPS satellite to set thetime. The vehicle needs to be in an open area toreceive the signal. See “Clock” under NavigationAudio System on page 82 for more information.

8

Setting the Region, Entering anAddress and Point of Interest, andStoring a Home Destination and PresetDestinationsBefore entering an Address, Point of Interest,Home, or Preset Destination, select theappropriate region that contains the finaldestination. Your vehicle must be stopped toperform this operation.

Setting the RegionTo set the region, do the following:


2. Insert the DVD map disc. See “Installing theMap DVD” under Maps on page 67 for moreinformation.

3. A notice may appear. Touch the Agree screenbutton to proceed.If the radio is already on with a map discinserted, press the NAV hard key.

4. Press the MENU screen button.

5. Press the < Enter Destination screen button.

6. Press the Region screen button.

7. Select the appropriate region numbered screenbutton that contains your final destination.

The system will return to the Enter Destinationmenu. See Enter Destination on page 20 for moreinformation.

Entering an AddressTo set a destination by entering a street address,do the following:





5. Press the < Enter Destination screen button.Verify that the selected Region is correct.

9

6. Press the 2 Address screen button.

7. Enter the street name using the alpha keypadon the screen.Do not enter directional information or streettype, and use the space symbol screen button(U) between street or city names. Forexample, the street name N. Royal Oak Rd.should be entered as royalUoak. Usethe backspace (V) screen button if anincorrect character has been entered.

8. Select the desired street name with thecorrect designation (Dr., Ln., St., etc.) fromthe list.

9. If there is more than one city, the system willdisplay the list of cities that have a street withthat name. Select a city from the list orselect the Input Name screen button to inputthe city name.

10. Enter the house number using the numerickeypad on the screen and touch the OKscreen button.A map screen will appear with the destinationmarked.

11. Select the h (destination) symbol screenbutton.

12. Select the Guide screen button.

13. Once you begin driving you will hear an audioprompt to “Proceed to the highlighted route.”You are now in route guidance mode.

See “Address” under Enter Destination on page 20for more information.

Entering a Point of Interest (POI)To set a destination by entering a Point of Interest(POI), do the following:





5. Press the < Enter Destination screen button.Verify that the selected Region is correct.

10

6. Press the K Point of Interest screen button.

7. Enter the specific title of the POI in theName space (i.e. Washington Monument)using the alpha keypad on the screen.

8. Select the POI from the list.

9. If there is more than one city, the system willdisplay the list of cities that have a street withthat name. Select a city from the list or selectthe Input Name screen button to input thecity name.A map screen will appear with the destinationmarked.




Using the Category or City selections will aid thesystem in finding your POI by limiting thesearch options. See “Point of Interest (POI)” underEnter Destination on page 20 for more information.

Storing a Home Destination1. Press the power/volume knob to turn the

system on.




5. Press the N Stored Locations screen button.

6. Press the L Home screen button.

7. Press the Add screen button.

8. Press the Address screen button and enter alladdress information.

9. Press the OK screen button.A map screen will appear with the destinationmarked.

11

10. Press the OK screen button.

11. Press the back arrow screen button.

The L Home icon will be highlighted on theEnter Destination screen. See “Using YourHome or Preset Destinations” later inthis section for more information.

Storing a Preset Destination1. Press the power/volume knob to turn the

system on.





6. Press the & Previous Dest. screen button.

7. Press the Add screen button, then select thenumbered preset button for the destination toappear as.

8. Press the Address screen button and enter alladdress information.

9. Press the OK screen button.A map screen will appear with the destinationmarked.

10. Press the OK screen button.

11. Press the back arrow screen button.The numbered preset destination will behighlighted on the Enter Destination screen.See “Using Your Home or Preset Destinations”next in this section for more information.

12

Using Your Home or PresetDestinationsThese destinations are available for selectionwhile driving.





5. Press the < Enter Destination screen button.

6. Select the L (Home symbol) or one of theavailable preset destination symbols. A mapscreen will appear with the destinationmarked.




Canceling GuidanceGuidance will be canceled once you arrive at yourfinal destination. To cancel guidance prior toarrival at the final destination, do the following:

1. Press the NAV hard key to access themap screen.

2. Press the MENU screen button on the mapscreen.

3. Press the E Route Options screen button.

4. Press the Cancel Guidance screen button.

5. Press the Yes screen button to confirmcancellation.

13

Stored LocationsOnce a destination has been stored, the addressinformation can then be edited and deleted.See Stored Locations on page 40 for moreinformation on other features that can be stored,edited, and deleted.

To delete the stored home destination, do thefollowing:






6. Press the L Home screen button.

7. Press the Delete screen button.

8. A confirmation pop-up screen willappear: select Yes to delete; selectNo to cancel the operation.

To delete a waypoint or a stored presetdestination, do the following:1. Press the power/volume knob to turn the

system on.2. Insert the DVD map disc. See “Installing the

Map DVD” under Maps on page 67 for moreinformation.


4. Press the MENU screen button.5. Press the N Stored Locations screen button.

6. Press the $ Dest. & Way Pt. or the &Previous Dest. screen button.

7. Press the Delete screen button, then selectthe way point or the numbered preset buttonto delete.

8. A confirmation pop-up screen willappear: select Yes to delete; selectNo to cancel the operation.

14

Guidance VolumeTo adjust the volume of voice guidance prompts,do the following:.

1. Press the NAV hard key to access the mapscreen.

2. Press the MENU screen button on the mapscreen.

3. Press the I Navigation Set Up screenbutton.

4. Press the > Guidance Volume screen button.

5. Select the desired volume or select Off.The system will play back the new volumelevel.

See “Guidance Volume” under Navigation Set Upon page 52 for more information.

Cleaning the DisplayIf the panel or the display is stained, wipe it with adry, soft cloth, such as a silicon cloth.

Notice: If you use abrasive cleaners whencleaning glass surfaces, you could scratch theglass. When cleaning the glass, use only asoft cloth and do not spray cleaner directly onthe system.

Do not apply spray cleaner directly to the system,the cleaner could affect the mechanical parts.

Do not wipe the panel with a hard cloth or use avolatile liquid such as thinner or alcohol, itcould scratch the surface or erase the characters.

15

✍ NOTES

16

Features and Controls .................................. 18Using the Navigation System ....................... 18Nav. (Navigation) Menu ............................... 20Enter Destination ......................................... 20Stored Locations ......................................... 40Navigation Set Up ....................................... 52Route Options ............................................. 60Maps ........................................................... 67Symbols ...................................................... 69

Head-Up Display (HUD) .............................. 75Keyless Access System .............................. 76Global Positioning System (GPS) ................ 76Vehicle Positioning ...................................... 77Problems with Route Guidance ................... 78If the System Needs Service ....................... 79Ordering Map DVDs .................................... 79Database Coverage Explanations ................ 80

Section 2 Features and Controls

17

Features and Controls

Using the Navigation SystemThis section presents basic information to operatethe navigation system.

Use the hard keys located on the navigationsystem along with the available touch screenbuttons on the navigation screen to operate thesystem. See Navigation System Overview onpage 4 for more information.

Once the vehicle is moving, various functions willbe disabled to reduce driver distractions.

Hard KeysThe following hard keys are located on thenavigation system:

X (Open/Close Faceplate): Press this keylocated at the bottom of the Navigation Screen toopen or close the faceplate.

XB (Eject CD): Press the eject CD key nextto the CD loading slot to eject CDs. See CD Playeron page 95 for more information.

X DVD (Eject Map Database DVD): Press theeject DVD key next to the DVD loading slot toeject the map DVD. See “Installing the Map DVD”under Maps on page 67 for more information.

Power/Volume Knob: Press the power/volumeknob to turn the audio and navigation systems onand off. Turn the knob to increase or decreasethe volume to the audio system.

g (Voice Recognition): Press this key toactivate the voice recognition system. See VoiceRecognition on page 108 for more information.

NAV (Navigation): Press this key to access themap screen. If this key is pressed when a mapscreen is displayed and you are in route guidance,the system will repeat the last voice command.

SRCE (Source): Press this key to accessthe audio source screen. See Navigation AudioSystem on page 82.

e / z (Audio/Screen Adjust): Press this key toaccess the Audio Adjust and Screen Adjustscreens. See Navigation Audio System onpage 82.

18

QO SEEK R (Seek/Tune): Press theseek/tune arrows to go to the next or previousradio station and stay there, or to tune in a station.See Navigation Audio System on page 82.

Alpha-Numeric KeypadLetters of the alphabet, symbols, punctuation, andnumbers will be displayed on the navigationscreen as an alpha or numeric keypad. The alphakeypad will be displayed when the systemneeds input of a city or street name. Touch theSym. (symbol) screen button at the bottom of thealpha keypad to access the numeric keypadwhen inputting a house address, punctuation mark,or other character. Touch A - Z to return to thealpha keypad.

All characters are touch-sensitive screen buttons.Touch a character to select it.

U (Space): Touch this screen button to enter aspace between characters or the words of a name.

V (Back space): Touch this screen button if anincorrect character has been selected.

To make name selections easier, the system willonly allow you to select a character which canfollow the last one entered. For example, if a Z isentered, a T will not be available to select. Thesystem will highlight the available characters.

If a name is not available after input, it may needto be inputted differently, the map DVD databasemay not contain that information, or the correctsearch area has not been selected. See DatabaseCoverage Explanations on page 80 for moreinformation.

Touch-Sensitive ButtonsTouch-sensitive buttons, or screen buttons, arelocated on the screen. When a screen button hasbeen selected, a beep will sound. These buttonswill be highlighted when a feature is available.There are also some toggle screen buttons that willbe light color when active.

19

Nav. (Navigation) MenuPress the NAV hard key to access the mapscreen. Press the MENU touch screen button onthe map screen.

From this screen all of the navigation systemfeatures can be accessed.

Enter Destination

Press the < Enter Destination screen button toaccess the ENTER DESTINATION screen.From this screen, several options are available toplan a route by entering destination points.

Once a destination entry is complete, regardlessof which method was used, a map screen with thedestination previewed will display. You canchange route preferences, route options, mapappearances, or add a waypoint at this time.You may also set the destination without makingany further changes. See “Getting Started on YourRoute” later in this section for more informationon your choices once a destination has beenentered.

This menu has two pages. To view the secondpage, press the 1/2 arrow button.

20

RegionThe ENTER DESTINATION screen displays amap of the United States and a part of Canadadivided into 11 regions.

Before selecting a destination entry method,review the search area map to make sure yourdestination is located in the highlighted region.

Touch the Region screen button from the ENTERDESTINATION screen to see a list of statesincluded in the highlighted region, or to changethe region. The SEARCH AREA screen willdisplay. Touch the numbered screen button to theleft of the search area map that correspondswith the numbered region you wish to select or toview a list of states included in that region.Touch the down arrow to the left of the searcharea map to select CAN (Canada). Once theregion has been selected, the region willbe highlighted on the map. Touch the back key toreturn to the ENTER DESTINATION screen.

21

AddressThe address destination entry method allows youto input an address by providing the systemwith a street name or city.

2 Address: Touch this screen button to accessthe ADDRESS screen. You can enter theaddress one of two ways: street first or city first.

To input the street name first, do the following:

1. Touch the Street screen button from theaddress menu and start inputting the streetname using the alpha keypad.

A list of available street names willautomatically display if there are less thanfive street names available. Select theList screen button at any time to view theavailable street names. The box at the end ofthe Street entry field will contain the numberof street names available in the currentgenerated list.

2. Select the desired street name with the correctdesignation (Dr., Ln, St., etc.) from the list.

3. If the system determines that the street isfound in only one city within the searcharea that city will automatically be selected.If there is more than one city, the systemwill display the list of cities that have a streetwith that name. Select a city from the listor select the Input Name screen button to inputthe city name.

4. The house number screen will display, enterthe house number using the numeric keypad.

5. Once the correct house number is selected,press the OK screen button.A map screen will appear with the destinationmarked.

22


7. Select the Guide screen button.See “Getting Started on Your Route” later inthis section for more information.

To input the city name first, do the following:

1. Touch the City screen button.

2. Select from the choices shown on the cityscreen: Any City, 5 Nearest Cities, InputCity Name, or from the Last 5 Cities used.

• Any City — The system will request input ofa street name, then generate a list of allcities containing that street name. Select acity from the list.

• 5 Nearest Cities — The system will display alist of five cities closest to your vehicle’scurrent position. Select a city from the list.

• Input City Name — The keypad will displayfor inputting the city name. Input the cityname and then select the city from the list.

• Last 5 Cities — The city names of the lastfive cities that were stored as a previousdestination will display. Select a city fromthe list.

3. The screen to input the street name andhouse number will display. Input the streetname using the alpha keypad. A list ofavailable street names will display if there areless than five street names available.Select the List screen button at any time toview the available street names. The boxat the end of the Street entry field will containthe number of street names available inthe current generated list.

4. Select the desired street name with the correctdesignation (Dr., Ln, St., etc.) from the list.

5. The house number screen will display, enterthe house number using the numeric keypad.Once the correct house number is selected,a map screen will appear with the destinationmarked.



23

Point of Interest (POI)The Point of Interest (POI) destination entrymethod allows you to select a destination from thePOI list.

K Point of Interest: Touch this screen buttonfrom the ENTER DESTINATION screen to accessthe POINT OF INTEREST screen. This screen hasthree options to select/input the destination. Eitherinput the name of the POI using the alpha keypad,select a category from the category list, or selectthe city by selecting the City screen button.

To input the POI name, do the following:

1. Use the alpha keypad to enter the POI name.Touch Sym. (symbol) to select symbols andnumbers for the POI, touch Others toselect special characters for the POI, or touchA - Z to return to the alpha keypad.A list of POIs will appear using the informationfrom the alpha keypad input. A list of availablePOIs will display when there are less thanfive POIs available. Touch the List screenbutton at any time to view the available POIs.

2. Select the desired POI from the list.

3. If the system determines that the POI is foundin only one city within the search area thatcity will automatically be selected.If there is more than one city, the system willdisplay the list of cities that have a POIwith that name. Select a city from the list orselect the Input Name screen button toinput the city name.Once all of the information is selected, a mapscreen will appear with the destinationmarked.

24



To select a POI from a category, do the following:

1. Touch the Category screen button from thePOINT OF INTEREST screen to view a listof POI categories.

2. Select a category, and then a sub-category.

3. The system will display available POIs in theselected sub-category or if the list is too longthe system will display the alpha keypad.

4. If the alpha keypad is displayed, input the POIname until a list of available POIs appear.

5. Select the POI from the list.

6. If the system determines that the POI is foundin only one city within the search area thatcity will automatically be selected.If there is more than one city, the system willdisplay the list of cities that have a POIwith that name. Select a city from the list orselect the Input Name screen button toinput the city name.Once all of the information is selected, a mapscreen will appear with the destinationmarked.



25

To select a POI by inputting a city name, do thefollowing:

1. Select the City screen button, then select: AnyCity, 5 Nearest Cities, Input City Name, orfrom the Last 5 Cities used.

• Any City — The system will request input ofa POI name, then generate a list of allcities containing that POI name. Select acity from the list.

• 5 Nearest Cities — The system will display alist of five cities closest to your vehicle’scurrent position. Select a city from the list.

• Input City Name — The keypad will displayfor inputting the city name. Input the cityname and then select the city from the list.

• Last 5 Cities — The city names of the lastfive cities that were stored as a previousdestination will display. Select a city fromthe list.

2. Use the alpha keypad to enter the POI name.Touch Sym. (symbol) to select symbols andnumbers for the POI, touch Others toselect special characters for the POI, or touchA - Z to return to the alpha keypad.

3. A list of POIs will appear using the informationfrom the alpha keypad input. A list of availablePOIs will display when there are less thanfive POIs available. Touch the List screenbutton at any time to view the list ofavailable POIs.

4. Select the desired POI from the list.A map screen will appear with the destinationmarked.



26

MapThe map destination entry method allows you toselect a destination by scrolling on the map.

I Select from Map: Touch this screen buttonfrom the ENTER DESTINATION screen toenter the map destination entry method, then dothe following:

1. Touch the map for the desired area you wishto set as your destination.

2. Use the zoom in/out function to view thedirection of the desired area.

3. Pressing/holding and dragging on the map willactivate fast scrolling. Press/touch once onthe area to which you would like to move thecurrent position mark.Once the scroll symbol is on the location, theaddress information will display on themap screen.



27

EmergencyThe emergency destination entry method allowsyou to enter a destination by selecting fromthree categories: Police Station, Hospital, orDealer.

| Emergency: Touch this screen button fromthe ENTER DESTINATION screen to accessthe EMERGENCY screen. The system will displaythe address, longitude, and latitude informationof your vehicles current position.

To use this destination entry method, do thefollowing:

1. Select a category. A list of destination(s) willdisplay with the name of the destination andthe distance from your vehicle’s currentposition.

2. Select a destination point from the list. TouchName Sort to sort the list by name, or DistSort to sort the list by distance from thevehicle’s current position.After selecting a destination from the list, amap screen will appear with the destinationmarked.



28

Memory PointsThe memory points destination entry methodallows you to select a destination from a list ofpoints that have been previously stored.

To store, edit, and delete memory points seeStored Locations on page 40 for more information.

N Memory Point: Touch this screen button fromthe DESTINATION ENTRY screen to accessthe MEMORY POINTS screen.


1. Select the category/folder in which thememory point has been stored. Selectfrom PERSONAL, BUSINESS,ENTERTAINMENT, or MARKED POINTfolders.

2. Sort the list by distance, icon, name or datestored.

3. Select the desired memory point.After selecting a memory point from the list, amap screen will appear with the destinationmarked.



29

Previous DestinationThe previous destination entry method allows youto select a destination from a list of previousdestination points.

h Previous Destination: Touch this screenbutton from the ENTER DESTINATION screen toaccess the PREVIOUS DEST screen. Thesystem will store up to 100 points that have beenpreviously input. As new destinations areentered, the system will automatically delete theoldest destinations and add the new entries.

To use the previous destination entry method, dothe following:

1. Select a previous destination from the list.Use the Sort by Name/Date function asnecessary. Also from this menu you can selectthe previous start point option. This optionis available while the vehicle is moving.To use the previous start point option from thePREVIOUS DEST screen, select thePrevious Start Point screen button.

2. After selecting a destination from the list, amap screen will appear with the destinationmarked.



30

IntersectionThe intersection destination entry method allowsyou to set two intersecting streets as yourdestination.

? Intersection: Touch this screen button fromthe ENTER DESTINATION screen to accessthe INTERSECTION screen.


1. Enter the first of two streets in the intersection.A list of available street names will displaywhen there are less than five available. Touchthe List screen button at any time to viewthe available street names.

2. Select a street from the list, or continue tospell the street name to further reduce thenumber of available street names.

3. After the first street has been selected, enterthe second street name. The List button mayagain become available.

4. Select the second street from the list, orcontinue to spell the street name to furtherreduce the number of available street names.After both streets have been selected, a mapscreen will appear with the destination marked.



31

Freeway Entrance/ExitThe freeway entrance/exit destination entrymethod allows you to select a destination byentering a freeway entrance or exit point.

= Freeway Ent (Entrance)/Exit: Touch thisscreen button from the ENTER DESTINATIONscreen to access the FREEWAY ENT/EXITscreen.


1. Enter the freeway name. Use abbreviations,such as I - 75, rather than spelling outInterstate.The system will display a list of freeways.

2. Select a freeway from the list, and selectwhether you want an entrance point or anexit point.Select an exit/entrance point from the list orinput the point by name. Sort the list by nameor by distance.After selecting a point from the list, a mapscreen will appear with the destination marked.



32

Phone NumberThe phone number destination entry methodallows you to select a destination by entering aphone number. The phone number must be in thelist of POIs that is contained on the map DVDfor the system to retrieve the destination.

U Phone Number: Touch this screen buttonfrom the ENTER DESTINATION screen to accessthe PHONE NUMBER screen.


1. Input the phone number of a POI using thenumeric keypad.If the phone number can be found on the mapDVD, a map screen will appear with thedestination marked. If the phone number isdependent on the area code, a list of POIs willappear to select from. Once a POI isselected, a map screen will appear with thedestination marked.



33

CoordinatesThe coordinates destination entry method allowsyou to select a destination by entering latitude andlongitude coordinates.

) Coordinates: Touch this screen button fromthe ENTER DESTINATION screen to accessthe COORDINATES screen.


1. Touch N (North) or S (South) next toLAT (latitude) to enter the direction ofthe latitude coordinate.

2. Input the numeric portion of the latitudecoordinate using the keypad.

3. Touch E (East) or W (West) next toLONG (longitude) to enter the directionof the longitude coordinate.

4. Input the numeric portion of the longitudecoordinate using the keypad.

5. Once both coordinates are entered, touch theOK screen button.A map screen will appear with the destinationmarked.If the coordinates are outside of the coveragearea on the map, you will be informed thatthere is no information on that location.

34



Preset DestinationThe preset destination entry method allowsyou to set a destination by choosing from one offive previously stored destinations. Besideshome, these are the only destinations available toset while the vehicle is moving.

To store, edit, or delete a preset destination, see“Dest. & Way Pt. (Destination & Way Point”under Stored Locations on page 40.


1. Select a preset destination number buttonfrom the ENTER DESTINATION screen.The screen buttons are located on the bottomof the screen.A map screen will appear with the destinationmarked.



HomeThis feature allows you to plan a route toone previously stored destination that you haveselected as a home. If a home destination isnot stored, the home button will not be available.Besides preset destinations one through five,this destination is the only other one available toset while the vehicle is moving or by voicerecognition.

To store, edit, or delete a home location, seeStored Locations on page 40.

35

L (Home): Touch this screen button from theENTER DESTINATION screen to set a homedestination.


1. Touch the Home button from the ENTERDESTINATION screen.

2. The system will then set your preset homedestination as the current destination. Tostore a preset home destination, see StoredLocations on page 40.A map screen will appear with the destinationmarked.



Getting Started on Your RouteOnce a destination has been entered, you canperform one of the following options:

h (Destination): Touch this button to set theentered destination as it is, without furtheradjustment.

36

o (Waypoint): Touch this button to enter thispoint as a waypoint along the route. This featureallows you to enter up to five stops on theway to your destination. See “Dest. & Way Pt.(Destination & Way Point)” under Stored Locationson page 40 for more information about addingand deleting waypoints.

Route Preference: Touch this screen button toaccess the ROUTE PREFERENCES screento adjust the route preferences. The current settingis displayed in the Route Preference section ofthe map screen. See “Route Pref.” underRoute Options on page 60 for more information.

Once the route preferences have been set, thesystem will display the map screen.

After selecting the h (destination) symbol, thefollowing screen buttons will become available.

37

Chg. (Change) Route: Touch this screen buttonto go to the Route Options menu. See RouteOptions on page 60 for more information.

Guide: Touch this screen button to start routeand voice prompt guidance.

Three RoutesThe 3 routes screen will give you a selection ofselecting three different routes to get you toyour destinations. To use the 3 routes option, dothe following:

1. Select the 3 routes button on the map screen.

38

The system will calculate up to three differentversions of your current route in threedifferent colors: Quick, Normal, and Short. Theroutes are shown with distance to destinationand estimated travel time, or select theInfo screen button to access the INFO FOR3 ROUTES screen. From this screen, you canview the following information:

• G (Estimated Travel Time) — This iconshows the route’s estimated time of travel.

• J (Straight-Line Distance) — This iconshows the route’s straight-line distance todestination.

• W (Toll Road) — This icon shows thedistance traveled on toll roads.

• c (Freeway Travel) — This icon shows thedistance traveled on freeways.

• b (Ferry) — This icon shows the distancetraveled by ferry.

• { (Time Restricted Roads) — This iconshows the distance traveled ontime-restricted roads.

2. Select the Quick, Normal, or Short screenbutton.A map screen will appear with the destinationmarked.

3. Select the Guide screen button to start routeand voice guidance.

39

Stored Locations

Select the N Stored Locations screen buttonfrom the NAV. MENU to access the STOREDLOCATIONS screen. From this screen, you canaccess the following options:

Memory Points

N Memory Points: This feature allows you tostore memory points. You can store them inthe four categories listed: Personal, Business,Entertainment, and Marked Point. These categorynames can be changed for your convenience.

To store a point:

1. Touch the Memory Points screen button fromthe STORED LOCATIONS screen.

2. Select one of the folders/categories listed.

3. Select the Add screen button.

4. Select the desired method of entering adestination to enter the memory point.See Enter Destination on page 20 for moreinformation. A map screen will appeardisplaying the selected memory point location.

40

5. If available, touch the INFO button to view theaddress information of the selected point.

6. Touch OK to store the point as a memory point.

To edit the name of a stored point:


2. Select the folder/category that the memorypoint exists in.

3. Select the List screen button.

4. Select the memory point to edit. Use the sortfeature to sort by distance, icon, name, ordate as needed.

5. Touch the Name screen button from the EDITMEMORY POINT screen.

6. Use the backspace screen button to deletethe current name or use the alpha keypad tomake changes.Select the Show Name On screen button tohave the name of the point appear on the mapscreen.

7. Touch the back screen button to store thechange.

To change the icon associated with a memorypoint:





5. Touch the Icon screen button from the EDITMEMORY POINT screen.

6. Select the desired icon. There are two pages(52) icons, six icons that have soundsassociated with them, and a No Icon button toselect from.Select the With Sound screen button, and thesound icons will display. To hear the soundof the icon, touch the Sound screen buttonnext to each icon. If the sound icons are used,the associated sound will be heard whenthe vehicle is approximately 650 ft (200 m)from the memory point.

41

Select the No Icon screen button to not havean icon associated with the point.The new icon will display in the EDITMEMORY POINT screen, next to the Iconscreen button.

7. Touch the back screen button to store thechange.

To move the memory point from one folder/category to another:


2. Select the folder/category that the memorypoint currently exists in.



5. Touch the Category screen button from theEDIT MEMORY POINT screen.

6. Touch the new folder/category button youwant to move the memory point to.The system will display a message confirmingthe move.

To modify the position of the stored point:





5. Touch the Position screen button from theEDIT MEMORY POINT screen.The system will display the map screen withthe destination marked.

6. Touch the map to move the position of thememory point.

7. Touch OK when you have moved the memorypoint to the appropriate location.

8. The system will return to the EDIT MEMORYPOINT screen and will display the newaddress, longitude, and latitude for thechanged memory point.

42

To change the phone number of a memory point:

1. Touch the Memory Points screen buttonfrom the STORED LOCATIONS screen.




5. Touch the Tel. (telephone) screen button fromthe EDIT MEMORY POINT screen.

6. Use the numeric keypad to change the phonenumber.

7. Touch OK to store the changed phone number.

To delete a memory point:



3. Select the Delete screen button.

4. Select the memory point to delete from theDELETE POINT screen. Use the sort feature tosort by distance, icon, name or date as needed.

5. The system will display the map screen withthe position address and a pop-upconfirmation message. Select Yes to deletethe point; select No to return to the DELETEPOINTS screen and not delete the point.

To delete all of the memory points in afolder/category:1. Touch the Memory Points screen button from

the STORED LOCATIONS screen.

2. Select the desired folder/category.

3. Select the Del.All screen button.

4. The system will display a pop-up confirmationmessage. Select Yes to delete all the pointsin the folder/category; select No to cancelthe operation.

To change the name of the folder/category:


2. Select the desired folder/category.

3. Select the Edit Category screen button.

4. Use the alpha keypad to change the name ofthe folder/category.

5. Touch the OK screen button to save thechanges.

43

Avoid Area

3 Avoid Area: This feature allows you to storean area to be avoided while planning a route.Up to 10 points can be stored.

To store an avoid area point, do the following:

1. Touch the Avoid Area screen button from theSTORED LOCATIONS screen.

2. Touch the Add screen button from the AVOIDAREA screen.

3. Select the desired method of entering adestination to enter the memory point.See Enter Destination on page 20 for moreinformation. A map screen will appeardisplaying the selected memory point location.

4. If desired, reduce or enlarge the area aroundthe point you want to avoid by using theReduce or Enlarge screen buttons.It is recommended that when avoidinglocations on freeways, you reduce the avoidarea to the minimum scale. This will producean X on the map rather than a box. Thiswill ensure that the system knows you want toavoid the freeway itself, not necessarily thearea around the freeway.

5. Touch OK to store the area.

To change the name of the point to be avoided:


2. Touch the List screen button from the AVOIDAREA screen.

3. Select the point to be changed.

4. Touch the Name screen button.

44

5. Use the alpha keypad to add or to changethe name.Select the Show Name On screen button tohave the name of the point appear on the mapscreen.

6. Touch the OK screen button to save thechanges.

To change the position of the point to be avoided:

1. Touch the Avoid Area screen button fromthe STORED LOCATIONS screen.

2. Touch the List screen button from the AVOIDAREA screen.

3. Select the point to be changed.

4. Touch the Position screen button.

5. Touch the map to move the location.

6. If desired, reduce or enlarge the area aroundthe point you want to avoid by using theReduce or Enlarge screen buttons.

7. Touch OK to store the area.

To delete a point to be avoided:


2. Touch the Delete screen button from theAVOID AREA screen.

3. Select the point to delete. Use the scrollingarrows as needed.

4. The system will display the map screenwith the name of the point and a pop-upconfirmation message. Touch Yes to havethe point deleted; touch No to cancel thefunction.

To delete all of the points to be avoided:


2. Touch the Del.All screen button from theAVOID AREA screen.

3. The system will display a pop-up confirmationmessage. Touch Yes to have all of the pointsdeleted; touch No to cancel the function.

45

Destination & Waypoint

6 Dest. & Way Pt. (Destination &Waypoint): Waypoints are destinations that canbe added to your route before reaching thefinal destination. Waypoints can be added beforeor after entering a final destination. Waypointsthat were entered prior to setting a finaldestination, will delete if a final destination has notbeen entered. Up to five points can be storedas waypoints.

To add a waypoint:

1. Touch the Dest. & Way Pt. screen button fromthe STORED LOCATIONS screen.

2. Touch the Add screen button from the DEST.& WAY POINT screen.

3. Using the desired method of entering adestination, enter the way point. SeeEnter Destination on page 20 for moreinformation.A map screen will appear with the way pointmarked.

4. Select the o (Way point) symbol on the mapscreen to save the way point.

5. Repeat Steps 2 - 6 to add up to five waypoints to your route. After the first waypointhas been saved, the ADD WAY POINT screenwill appear and the waypoint will be on thescreen. The second through the fifth waypointwill not appear on the ADD WAY POINTscreen until the ADD button, next to thecorresponding waypoint row, is pressed. Afterthe ADD button has been pressed, thesystem will return to the STOREDLOCATIONS screen.

To change the order of the waypoints:


2. Touch the List screen button from the DEST. &WAY POINT screen.

3. From the CHANGE ORDER screen, select onthe addresses, in the order you would like themto fall on the route. After selecting the addressline, a number, indicating the order, will appearnext to the corresponding row.

4. Select OK to save the changes. The systemwill return to the STORED LOCATIONSscreen.

46

To change the location of a way point:


2. Touch the List screen button from the DEST. &WAY POINT screen.

3. Touch the Chg. Loc. screen button from theCHANGE ORDER screen.

4. From the CHANGE LOCATION screen, selectthe address of the location to change. A mapscreen will display with the destinationmarked.

5. Touch on the map to move the location of thewaypoint.

6. Touch the OK screen button to save thechanges. The system will return to theSTORED LOCATIONS screen.

To delete a way point from the current route:


2. Touch the Delete screen button from theDEST. & WAY POINT screen.

3. Select the way point/destination to delete.

4. The system will display a pop-up confirmationmessage. Choose Yes to delete the waypoint; touch No to cancel this operation.

To delete all of the way points on the route:


2. Touch the Del.All screen button from theDEST. & WAY POINT screen.

3. The system will display the map screen with apop-up confirmation message. Choose Yes todelete all of the way points; touch No tocancel this operation.

47

Home

L Home: This feature allows you to store, delete,and edit a home point destination.

To store the home destination, do the following:

1. Touch the Home screen button from theSTORED LOCATIONS screen.

2. Select the Add screen button.

3. Select a destination entry method from theSET HOME screen. See Enter Destinationon page 20 for more information.

4. Set the destination and touch OK.

5. Touch OK on the map screen and thedestination will be stored. The home icon willnow be highlighted on the ENTERDESTINATION screen.

To edit the home destination, do the following:


2. Select List from the HOME screen to changethe location.

3. Touch the map to move the location of thepoint.

4. Touch OK to save the change.

To delete the home point, do the following:


2. Select Delete from the HOME screen.

3. The system will display the map screen with apop-up confirmation message. Select Yes todelete the stored home position; selectNo to cancel the operation.

48

Previous Destination

B Previous Dest. (Previous Destination): Thesystem will automatically store up to 100 pointsthat have been previously input. As newdestinations are entered, the system willautomatically delete the oldest destinations andadd the new entries. See Enter Destinationon page 20 for more information.

To delete a specific destination from the previousdestinations list, do the following:

1. Touch the Previous Dest. screen button fromthe STORED LOCATIONS screen.

2. Touch the Delete screen button.

3. Select a destination from the list.

4. The system will display the map screen with apop-up confirmation message. Select Yes todelete the stored destination; select No tocancel the operation.

To delete all destinations from the previousdestinations list, do the following:

1. Touch the Previous Dest. screen button fromthe STORED LOCATIONS screen.

2. Touch the Del.All screen button.

3. The system will display the map screen with apop-up confirmation message. Select Yes todelete all of the stored destinations; selectNo to cancel the operation.

Preset Destination

A Preset Dest. (Preset Destination): Thisfeature allows you to store up to five presetdestinations. These destinations are stored on thenumbered buttons shown on the bottom of theENTER DESTINATION screen.

To store a preset destination, do the following:

1. Touch the Preset Dest. screen button from theSTORED LOCATIONS screen.

2. Select Add to add a preset destination, thenselect the numbered preset button for thedestination to appear as.

49

3. Select a destination entry method from theSTORE PRESET DEST. screen. See EnterDestination on page 20 for more information.

4. Set the destination and touch OK.

5. Touch OK on the map screen and thedestination will be stored. The presetdestination number will now be highlighted onthe ENTER DESTINATION screen.

To edit the name of a preset destination, do thefollowing:

1. Touch the Preset Dest. screen button fromthe STORED LOCATIONS screen.


3. Select the preset destination to edit.

4. Touch the Name screen button and use thealpha keypad to edit or add the name.Select the Show Name On screen button tohave the name appear on the map screen.

5. Touch the OK screen button to save thechange.The new name will display.

To change the position of a preset destination, dothe following:



3. Select the preset destination to change.

4. Touch the Position screen button from theEDIT PRESET DEST. screen. The systemwill display the map screen with thedestination marked.

5. Touch the map to move the position of thememory point.

6. Touch the OK screen button to save thechange.

50

To add or change the phone number of a presetdestination, do the following:



3. Select the preset destination to change.

4. Touch the Tel. (telephone) screen button anduse the numeric keypad to input or changethe phone number.

5. Touch the OK screen button to save thechange.

To delete a preset destination:


2. Select the Delete screen button.

3. Select the memory point to delete from theDELETE PRESET DEST. screen.

4. The system will display the map screen withthe position address and a pop-up confirmationmessage. Select Yes to delete the point; selectNo to cancel the operation and to return to theDELETE PRESET DEST. screen.

To delete all of the preset destinations:


2. Select the Del.All screen button.

3. The system will display a pop-up confirmationmessage. Select Yes to delete all of thepreset destinations; select No to cancel theoperation.

Memory Point Icons Display: Select this screenbutton to display memory point icons on the map.The button will be highlighted when the memorypoint icons are being displayed on the map.

Calculate: Touch this button to calculate yourroute. This button is available after a destinationhas been set.

51

Navigation Set Up

Select the MENU screen button to access theNAV. MENU screen.

I Navigation Set Up: Touch this screenbutton from the NAV. MENU screen to access theNAVIGATION SET UP screen. Several systemoptions are available for adjustment.

Two-Dimensional/Three-Dimensional(2D/3D) View

8 2D/3D View: Touch this screen button fromthe NAVIGATION SET UP screen. This featureallows you to change the view of the map betweena 2-dimensional and 3-dimensional view.

52

Map Screen 2D/3D: This will change the view ofall map screens.

Guidance Screen 2D/3D: This will change theview of the map screen while driving during routeguidance.

n / q (Scroll Arrows): Select the up or downarrows to tilt the view of the map screen.

4 (Back): Select this screen button to save thechanges.

Default: Press this button to cancel your changesand go back to the default settings (2D and 2D).

Quick POI Selection

C Quick POI Selection: This feature allowsyou to select the POI categories you wantavailable on the Quick POI (Q-POI) screen.

53

To replace the default POI categories on theQuick POI (Q-POI) screen, do the following:

1. Select the C Quick POI Selection screenbutton from the NAVIGATION SET UP menu.This screen will display the list of POIcategories.

2. Select the POI category that you would like tochange. The category to change will displaywith the list of categories to select from.Select the All Category List screen button todisplay all categories and sub-categories.

3. Select a different POI category. The POIcategory icon to change will be replacedwith the new POI category icon at the top ofthe screen. This POI will now be availableon the Q-POI screen.

Quick POIOnce categories have been selected on the Q-POISELECTION screen, the POI categories arenow available on the Quick POI screen. From thisscreen you can select the POI icons that youwould like to display on the map screen. You caneither select a POI for a final destination or asa waypoint. The Quick POI screen is availablewhen the scale is 1⁄2 mile (1 km) or less.

To use the QUICK POIscreen, select the POIscreen button fromthe map screen.

54

The POI categories that were selected on theQ-POI SELECTION screen will display.

To have the POI icons appear on the map screen,select the POI category. The POI category iconwill display at the top of the screen.

List Categories: Select this screen button todisplay more categories to select from.

All Local POIs

1. Select this screen button to select a POI as adestination. A list of all of the local POIswithin a 5 mi. (8 km) radius of your vehicle’scurrent position will display. This list isgenerated from the POI categories that havebeen selected and appear at the top ofthe QUICK POI screen.Use the Sort by Dist. (distance), Icon, Name,or Route screen buttons. Use the up anddown scroll arrow screen buttons to scrollthrough the list.

2. Select the POI. The map screen will displaywith the scroll symbol around the selectedPOI. The name and the POI information willalso display on the map screen.


4. Select the Guide screen button.See “Getting Started on Your Route” for moreinformation.

55

All Category List: This screen button will appearonce the List Categories screen button hasbeen selected. Press this screen button to displaya list of sub-categories.

Show: Select this screen button to display themap screen.

Delete: To delete a category, do one of thefollowing:

• To delete the last added POI category, selectthe Delete screen button.

• To delete a specific POI category, select thatPOI category from the list.

POI Off: Select this screen button to delete all ofthe POI categories in the list.

Calibration

5 Calibration: Touch this screen button from theNAVIGATION SET UP screen. This featureallows you to recalibrate the navigation system.

The Calibration screen, allows the adjustment ofyour vehicle’s position or the vehicle speed signal.

56

To correct the position of your vehicle on the map(for example, if your vehicle has been shipped)or to change to the current position.

1. Select the Position/Direction screen button.The map screen will display with yourvehicle’s current position.

2. To change your vehicle’s position, touch themap screen.Use the zoom in/out function to view thedirection of the desired area.Pressing/holding and dragging on the map willactivate fast scrolling. Press/touch once onthe area to which you would like to move thecurrent position mark.

3. Touch the OK screen button once yourvehicle is in the current position.If a route had already been set, the mapscreen will display, select Guide to changeyour route to your vehicle’s new position.

Once the process of changing your vehicle’scurrent position is complete, the mapscreen will display with rotate arrow screenbuttons around your vehicle.

4. To change the direction of your vehicle, presseither arrow screen button to rotate yourvehicle to the correct direction.

5. Once your vehicle is facing the correctdirection, select the OK screen button.

See Problems with Route Guidance on page 78for more information.

If there are tire pressure differences or a sparetire is installed, the system will automaticallyre-calibrate the system but it may take longer.To calibrate the vehicle speed signal, touchthe Distance screen button. See VehiclePositioning on page 77 for more information.

57

User Settings

J User Settings: Touch this screen button fromthe NAVIGATION SET UP screen. This featureallows you to turn on and off several route options.

From this screen, you can adjust the following:

Road Restriction Warnings: This option instructsthe system to notify you when the current routehas traffic restrictions.

Arrival Time G (Time of Arrival): This option willdisplay the estimated time of arrival to thedestination.

Arrival Time \ (Time to Destination): Thisoption will display the amount of drive timeestimated to arrive at the destination.

Guidance Screen: This option will turn theguidance screen on and off.

Freeway Information: This option will displayfreeway exit information. This is only available onfreeways during route guidance.

58

Restore System Defaults

D Restore System Defaults: Select thisfeature from the NAVIGATION SET UP screen tochange all adjustable system settings to factorydefaults.

OK: Select this screen button to restore thesystem defaults.

Average speed Default: Select this option to setthe average speed to default. The system monitorsthe speed on different roads and updates theaverage speed the vehicle travels at. This averagespeed is used to calculate the time it will take toreach the destination when you set a route.

Guidance Volume

> Guidance Volume: This feature allows you toadjust the volume of voice guidance prompts.Select Off to turn voice guidance prompts off.

59

Route Options

Select Route Options from the NAV. MENUscreen to access the ROUTE OPTIONS screen.This menu has many features to customizeroute guidance. A route must first be set to usethese features. See Enter Destination on page 20for more information on entering a destination.

Search Condition

H Search Conditn (Search Condition): Thisfeature will access the SEARCH CONDITIONscreen.

The search condition screen allows you to viewyour current destination and to change theplanning methods between each destination. Eachdistance between waypoints and final destinationcan have an individual setting.

60

n / q (Scroll Arrows): Use the up and downarrows to scroll through each route.

Quick/ Normal/Short: Select one of the routepreference options to change the planning method.

Calculate: After selecting the new methods,select Calculate to plan the route with the changes.The map screen will display.

Detour

7 Detour: Select a detour if there isconstruction work, or traffic delays that prevent theoriginal route from being used.

From this screen, you can select a 1 mile, 3 mile,or 5 mile detour or select to detour the wholeroute. After selecting the detour, the system willcalculate the alternate route and the new route willdisplay on the map screen.

61

Route Preferences

F Route Pref. (Route Preferences): You canselect to have certain types of roads/ferriesincluded in your route. See “Getting Started onYour Route” under Enter Destination on page 20for more information.

The following route preferences can be selectedon or off:

c (Allow Major Roads): This feature allows thesystem to use expressways when calculating aroute. If there is no way to reach your destinationwithout using major roads, the system willautomatically include major roads.

l (Allow Time Restricted Road): This featureallows the system to use time restricted roadswhen calculating a route. These are roadsthat may be closed during the winter season.

W (Allow Toll Road): This feature allows thesystem to use toll roads or pay roads whencalculating a route.

b (Allow Ferry): This feature allows the systemto use ferries when calculating a route.

Calculate: Select this screen button to update thechanges in the current route. The map screenwill display.If any of these features are turned off, the buttonwill be dark and there will be a red slashthrough the icon on the map screen.Once the route preferences have been set, selectthe back button to return to the previous screen.

62

Destination and Waypoint

o Dest. & Way Pt. (Destination andWaypoint): This feature allows you to edit theselected destination and waypoints using thisscreen. See “Dest. and Way Pt. (Destination andWay Point)” under Stored Locations on page 40for information on storing destinations andwaypoints.

Up to five waypoints and one destination can beentered. The following functions are available:

Add: This button will access the Store Dest. &Waypoint screen. You can add a waypointor change the destination.

List: Touch this button to change the order of thestops in the route and to change the location ofthe stops.

Delete/Del. All: These buttons allow you to deletewaypoints on the route or to delete the entireroute.

Display route

9 Display route: Select this button from theROUTE OPTIONS menu to view the entire route.The start point and destination, the time it willtake to reach the destination, and distance,including the distance that is routed on each roadtype will display.

63

Turn List: Edit the route by selecting the TurnList screen button. A list of every turn on the routewill display. With the turn list displayed, you canselect to avoid streets/turns on the route.

Avoid: To avoid a street, select the Avoid screenbutton next to the turn. To cancel the avoidedturn, select Avoid again to deselect it.

Reroute: After selections have been made, pressthe Reroute screen button to replan the route.

Delete: To cancel an avoided turn after the routehas been replanned, press the Delete screenbutton. A list of all of the avoided turns will display.Select the street that you want to add back tothe route. A confirmation window will display.Select Yes to have the avoided street added backto the route. The Turn List screen will display.

Del. All (Delete All): To cancel all of the avoidedturns after the route has been replanned, pressthe Delete screen button. A list of all of the avoidedturns will display. Select the Del. All screenbutton. A confirmation window will display. SelectYes to have all of the avoided streets addedback to the route. The Turn List screen will display.

64

Route Preview

G Route Preview: Select this button from theROUTE OPTIONS menu to preview the entireroute in either direction and to edit the route.

Use the screen buttons at the bottom of thenavigation screen to move through the route.

bt (Skip to Start Point): Touch this screenbutton to skip backward to the start point, theprevious waypoint, or the previous available POI,depending on the mode selected.

bq (Scroll to Start Point): Touch this screenbutton to start a smooth scroll of the routebackwards to the start point, previous waypoint, orthe previous available POI, depending on themode selected. Touch this button again to increasethe scroll speed.

j (Pause): Touch this screen button to pausethe smooth scroll. Push either scroll button ( b qr h ) to restart the scroll.

rh (Scroll to Destination): Touch this screenbutton to start a smooth scroll of the route towardthe destination, next waypoint or next availablePOI, depending on the mode selected. Touch thisbutton again to increase the scroll speed.

uh (Skip to Destination): Touch this screenbutton to skip forward to the destination, nextwaypoint or next available POI, depending on themode selected.

Edit: Touch this screen button to change the waythe skip/scroll function operates. You can select tohave the skip/scroll go to the start point/destinationor to the next available POI or waypoint.

65

To next Dest. (Destination) or WP(Waypoint): Select this button to have theskip/scroll functions skip/scroll to the nextdestination or waypoint.

To next POI: To select this option, a POI categorymust be selected. Select this button to have theskip/scroll functions skip/scroll to the next availablePOI for the category. To change the POI category,touch the corresponding screen button next to thecategory. Touch the Delete screen button to haveno POIs appear on the map. The default POIs arethe same as those in the Quick POI group listing.

Calculate: Touch this screen button to calculatethe route with the changes.

Once the route has been calculated, this screenwill display. From this map screen, touch Guide tobegin route guidance or touch Chg. route toreturn to the ROUTE OPTIONS screen.

Cancel Guidance: Touch this screen button tocancel the current route.

66

MapsThis section includes basic information that youneed to know about the map database.

Regional MapsThe maps are stored on a DVD. The 48 contiguousUnited States and portions of Canada arecontained on one disc.

If a regional map does not contain a specific city,the map DVD may not contain the city or itmay be misspelled.

Refer to the Navigation System Map Disc manualto view a detailed explanation of map coverageand detailed city lists in each region. This manualwill be in the map DVD case when the vehicleis delivered from the factory.

Installing the DVD Map DiscWhen your vehicle is delivered from the factory,the dealer may have installed the map DVD. If themap DVD was not installed, do the following:

Read the following steps completely beforeoperating this feature.

1. Turn the ignition on.

2. Push theZ (open/close faceplate) buttonand the faceplate will open.

3. Load the map DVD into the DVD slot byinserting it partway. The system will pull it in.

4. Wait until the DVD is loaded properly andthen push theZ (open/close faceplate)button to close the faceplate.

Once the map DVD is inserted correctly, thesystem will display the CAUTION screen.

Agree: Touch this screen button to proceed tothe navigation system.

The map will appear showing your current vehicleposition.

67

Ejecting the DVD Map DiscWhen the DVD map disc is not loaded, you willnot be able to use the navigation portion ofthe system.


2. Push theX (open/close faceplate) buttonand the faceplate will open.

3. Press theX DVD key, located next to thebottom slot. The disc will eject.

4. Wait until the DVD is ejected properly andthen push theX (open/close faceplate)button to close the faceplate.

Setting the Search AreaSee Enter Destination on page 20 for informationon changing the search area.

Map AdjustmentsThe system allows you to adjust the scale of viewon the map. Also, as you drive, the map willscroll automatically based on the direction you aretraveling.

Map Scales

To view a larger orsmaller scale of themap, touch themap scale arrows.

You can change the level of map detail by eitherzooming in or zooming out using the arrowscreen buttons or by touching the scale on thebar. The system will adjust the map accordingly.The scale of a map can range from 1/32 of amile (0.05 km) to 128 miles (256 km).

68

Scrolling the Map

Touch anywhere on themap screen twice andthe scroll symbolwill appear. Use thisfeature to scroll acrossthe map.

If scrolling while your vehicle is in PARK (P), thesystem will scroll initially at a slower rate. Itwill increase if you continue touching the mapscreen.

If scrolling while your vehicle is in motion, thesystem will scroll to that location and stop.

If you have used the scroll feature to scroll themap and your vehicle icon becomes lost, press theNAV (navigation) hard key to return to thecurrent vehicle location on the map.

You can use the scroll feature on the map to set adestination. See “Map” under Enter Destinationon page 20 for more information.

SymbolsThe following symbols are the most commonsymbols that will appear on a map screen.

Your vehicle is shownas this symbol. Itindicates the currentposition and headingdirection of your vehicleon the map.

This symbol will appearon the map after a routehas been plannedmarking your finaldestination.

69

When a waypoint hasbeen planned, you willsee this symbol onthe map.

The waypoint symbol will be numbered from1 through 5 depending on how many waypointshave been set.

This symbol indicatesthe distance to the finaldestination. It onlyappears when time isnot available.

This symbol indicatesthe distance and theestimated timeremaining to the finaldestination or arrivaltime, depending on theoption selected. SeeNavigation Set Upon page 52 for moreinformation.

This symbol shows thestraight-line distance tothe final destination.

This symbol may appear before you start drivingon the route or if you are on a road wherenavigation guidance cannot be given. SeeDatabase Coverage Explanations on page 80 formore information.

70

This symbol indicatesthe map with North Up(North Up mode).

While in North Up mode, North will always be atthe top of the map screen regardless of whichdirection the vehicle is traveling. Touch this screensymbol to switch between North Up and HeadingUp modes.

This Heading Up modesymbol indicates themap with the vehicletravel direction up.

The shaded triangle indicates the North direction.While in Heading Up mode, the direction yourvehicle is traveling will always be at the top ofthe map screen. The vehicle icon will always be

headed in the direction your vehicle is traveling.Touch this screen symbol to switch betweenHeading Up and North Up modes.

This No GPS symbol willappear in the upper rightcorner of the map screenwhen your vehicle is notreceiving a GlobalPositioning System(GPS) satellite signal.

See Global Positioning System (GPS) on page 76for more information.

When a name is toolong to be displayed, anarrow symbol willappear. Touch the rightor left arrow screenbutton to scroll throughthe entire name.

71

This symbol indicatesthe position of the nextguidance maneuver.

Touch this symbol to setthe current route as thedestination.

Touch this symbol toenter a waypoint alongthe current route.

Touch this symbol tostore the location on thescreen as a memorypoint.

Map Appearance

Select this symbol fromthe map screen todisplay the mapappearance options.

Select from one of the following six options thatallow you different views and information ofthe map screen. Availability of these optionsdepends on the current route. The current viewwill be highlighted.

72

Select the single mapmode to display more ofthe map with a windowthat gives the directionand distance to theupcoming maneuver.

Select the dual viewsymbol to displaytwo map screens thatwill allow different scalelevels and headingdirection for eachwindow.

Touch anywhere inside the right screen and theEDIT RIGHT SCREEN screen will display. Changethe scale level, 2D and 3D view, and to turn thePOIs on and off. To change the heading direction,touch the north up or heading up symbol.

Select the turn listsymbol to display thenext three upcomingmaneuvers on the mapscreen when onroute guidance.

Directional arrows, street name, and distance tothe next turn will display. As you approach the nextturn, the system will automatically display azoomed-in view of the upcoming maneuver.

Select the arrowguidance symbol todisplay the next turn onthe map screenwhen on routeguidance.

Directional arrows, street name, and distance tothe next turn will display. As you approach the nextturn, the system will automatically display azoomed-in view of the upcoming maneuver.

73

Select this symbol todisplay only the nextmaneuver along with asmall map of themaneuver.

When approaching the next maneuver, the systemwill display a guidance window of the maneuver.This option can be turned off by the USERSETTINGS screen.

Select the highwayguidance symbol todisplay highwayguidance on the mapscreen.

The upcoming exit number, distance to the exit,available POIs at the exit, and a window withthe direction and distance to the next maneuverwill display.

Use the up and down arrows to scroll through thelist. To view the available POIs for an exit,select the exit, then select the Map screen button.

The system will display highway guidance anytime you have a planned route on a highwayor freeway. To turn this feature off, see “UserSettings” under Navigation Set Up on page 52 formore information.

Auto RerouteWhen a destination has been set and you are offof the planned route, the system will automaticallyplan a new route. The new route will behighlighted on the screen.

Traveling Across RegionsWhen driving through regions, the map screen willupdate to display your current location. To plan adestination in a different region, you must changethe region for the map DVD to access the correctinformation. To do so, do one of the following:

1. Change the selected region in the search areawhen you get closer to the area you aretraveling to. See Enter Destination on page 20or,

74

2. Change the selected region in the searcharea when entering your destination androute settings. See Enter Destinationon page 20.For example, if you were traveling fromMichigan to Florida, make sure that Florida isincluded on the selected region. Enter adestination in Florida under the ENTERDESTINATION menu.

Head-Up Display (HUD)When a route is planned the Head-Up Display(HUD) will display information when the vehicle isapproaching a turn. This information will displaywhen the vehicle is 0.5 mi. (0.80 km) away from aturn in residential areas and 2.0 mi. or 2.0 kmaway from a turn on freeways.

A. Directional Arrow — Displays the direction ofthe next turn.

B. Distance Bar — This will decrease as thevehicle approaches the turn.

C. Street Name Line — Displays the name of thestreet that you will be turning on.

D. Mile/Kilometer Scale — Indicates the scale ofthe distance bar. The scale is 0.5 mi. (0.80 km)in residential areas and 2.0 mi. or 2.0 km onfreeways. This value will change as youapproach the turn.

After completing a turn, the HUD will display thename and distance of the next street you willbe turning on for 10 seconds.

75

When HUD is displaying the turn-by-turn guidanceinformation, the vehicle’s shift lever gear will notdisplay in the HUD. The gear will display onthe Driver Information Center (DIC) screen. Oncethe destination has been reached or guidanceis cancelled, the HUD will again display the gearinformation. See Head-Up Display (HUD) inthe Index of your vehicle’s owner manual for moreinformation.

Keyless Access SystemWhen you start your vehicle you will see Driver 1or Driver 2 displayed on the Driver InformationCenter (DIC). The number on the back of the RKEtransmitter corresponds to driver 1 or driver 2.The navigation system can store memory points,audio presets, system settings, and last knowaudio mode for driver 1 and driver 2 individually.See “Vehicle Personalization” in the index ofyour vehicle’s owner manual for more information.

Global Positioning System (GPS)The Navigation System determines the position ofyour vehicle by using satellite signals, variousvehicle signals, and map data.

At times, other interferences such as the satellitecondition, road configuration, the condition ofthe vehicle and/or other circumstances caninterfere with the Navigation’s ability to determinethe accurate position of the vehicle.

The GPS shows the current position of yourvehicle using signals sent by the GPS Satellites ofthe United States Department of Defense.When your vehicle is not receiving signals fromthe satellites, a symbol will appear on themap screen. Refer to Symbols on page 69.

76

This system may not be available or interferencemay occur if the following happens:

• Signal obstructions caused by tall buildings,large trucks, tunnels,

• objects located on top of the instrument panel,

• satellites will not send signals if they arebeing repaired or improved,

• after-market glass tinting has been applied tothe vehicle’s windows.

Notice: Do not apply after-market glass tintingto the vehicle’s windows. Glass tinting willinterfere with the system’s ability to receiveGPS signals and cause the system tomalfunction. You might have to replace thewindow to correct the problem. This would notbe covered by your warranty.

For more information if you are experiencing aproblem, see If the System Needs Serviceon page 79 and Problems with Route Guidance onpage 78.

Vehicle PositioningAt times, the position of the vehicle on the mapmay be inaccurate due to one or more of thefollowing reasons:

• The road system has changed.

• The vehicle is driving on slippery roadsurfaces such as in sand, gravel and/or snow.

• The vehicle is traveling on winding roads.

• The vehicle is on a long straight road.

• The vehicle is approaching a tall building or alarge vehicle.

• The surface streets run parallel to a freeway.

• The vehicle has just been transferred by avehicle carrier or a ferry.

• The current position calibration is setincorrectly.

• The vehicle is traveling at high speed.

• The vehicle changes directions more thanonce, or when the vehicle is turning on aturn table in a parking lot.

77

• The vehicle is entering and/or exiting aparking lot, garage or a lot with a roof.

• The GPS signal is not received.

• A roof carrier is installed on your vehicle.

• The vehicle is equipped with tire chains.

• The tires are replaced.

• The tire pressure for your tires is incorrect.

• The tires are worn.

• The first time the map DVD is inserted.

• The battery is disconnected for several days.

• The vehicle is driving in heavy traffic wheredriving is at low speeds, and the vehicle isstopped and started repeatedly.

If you experience problems with your system, youmay need to calibrate the system. This may bedue to tire pressure differences, or if a spare tire isinstalled. To calibrate the system, see NavigationSet Up on page 52.

Problems with Route GuidanceInappropriate route guidance may occur under oneor more of the following conditions:

• You have not turned onto the road indicated.

• Route guidance may not be availablewhen using automatic rerouting for the nextright or left turn.

• The route may not be changed when usingautomatic rerouting.

• There is no route guidance when turning at anintersection.

• Plural names of places may be announcedoccasionally.

• It may take a long time to operate automaticrerouting during high-speed driving.

• Automatic rerouting may display a routereturning to the set waypoint if you are headingfor a destination without passing through aset waypoint.

78

• The route prohibits the entry of a vehicle dueto a regulation by time or season or anyother regulation which may be given.

• Some routes may not be searched.

• The route to the destination may not beshown if there are new roads, if roadshave recently changed or if certain roads arenot listed on the map DVD. See OrderingMap DVDs on page 79.

To recalibrate the vehicle’s position on the map,see Navigation Set Up on page 52.

If the System Needs ServiceIf your system needs service and you havefollowed the steps listed here and still areexperiencing problems, see your dealer forassistance.

Ordering Map DVDsYou will receive two free DVD map disc updateswith the purchase of your new vehicle. Updatesare necessary to make sure that your vehicle’snavigation system has the most accurateinformation available about streets/roads, points ofinterest, and business locations.

The updates are provided by the GM Nav DiscCenter at the first and second anniversary dates ofyour vehicle’s delivery date. About four to six weeksbefore those anniversary dates, you will receive apost card from the GM Nav Disc Center remindingyou that a free update is available. The center willrequest confirmation of your mailing address eitherby having you contact the toll-free number,1-877-NAV-DISC (1-877-628-3472), or the center’swebsite, www.gmnavdisc.com. After verifying youraddress you should receive the updated disc inabout two weeks. After receiving the updated disc,replace the old disc in the navigation system. See“Installing the DVD Map Disc” and “Ejecting theDVD Map Disc” under Maps on page 67. Dispose ofthe old disc to avoid confusion about which disc isthe most current.

79

If you have any questions about the operation ofthe navigation system or the update process,call the GM Nav Disc Center or go to the center’swebsite. If you need any future updates or areplacement disc, because the current disc is lost,damaged, or needs to be updated, call the GMNav Disc Center or order a new disc online.To order a disc, have your Vehicle IdentificationNumber (VIN) available. This helps the centermake sure you receive the correct and most up todate DVD map disc for your vehicle. See“Vehicle Identification Number (VIN)” in the Indexof your vehicle’s owner manual for moreinformation.

Database Coverage ExplanationsThe United States, excluding Alaska and Hawaii,and portions of Canada are contained on oneDVD disc. The map database contains threedifferent levels of coverage: detailed areas,non-detailed areas, and limited guidance areas.

• Detailed areas are available for the UnitedStates and Canada and are primarilylocated around metropolitan areas.

• Limited guidance areas are only available forthe United States. The roads are displayedon the map, but route and voice guidance isnot available.

• Non-detailed areas are available for Canadaonly. Major roads are included dependingupon available coverage.

For more detailed information on databasecoverage, see the Navigation System Map Discmanual included inside the map DVD case.

80

Navigation Audio System ............................. 82CD Player ................................................... 95Six-Disc CD Changer ................................ 101

Audio Steering Wheel Controls .................. 105Radio Personalization with Home and

Away Feature ........................................ 106

Section 3 Navigation Audio System

81

Navigation Audio SystemNotice: Before adding any sound equipmentto your vehicle, such as an audio system,CD player, CB radio, mobile telephone,or two-way radio, make sure that it can beadded by checking with your dealer. Also,check federal rules covering mobile radio andtelephone units. If sound equipment can beadded, it is very important to do it properly.Added sound equipment may interfere with theoperation of your vehicle’s engine, radio, orother systems, and even damage them.Your vehicle’s systems may interfere with theoperation of sound equipment that hasbeen added.

Notice: The chime signals related to seatbelts, parking brake, and other functions ofyour vehicle operate through the navigationsystem. If that equipment is replaced oradditional equipment is added to your vehicle,the chimes may not work. Make sure thatreplacement or additional equipment iscompatible with your vehicle before installingit. See “Accessories and Modifications” inthe Index of your vehicle’s owner manual.

Your vehicle has a feature called RetainedAccessory Power (RAP). With RAP, the audiosystem can be played even after the ignitionis turned off. See “Retained Accessory Power(RAP)” in the Index of your vehicle’s owner manualfor more information.

The audio system is operated using the navigationsystem menus.

Playing the Radio

Power/Volume Knob: Press this knob to turn theaudio system on and off. Turn the knob to increaseor decrease the volume to the audio system.

¦O SEEK ¥: Press and hold the up or downarrow until a beep is heard to go to the next orprevious station and stay there. Press andhold either arrow to perform a fast seek.

SRCE (Source): Press this hard key to displaythe main audio screen.

82

Audio Adjust Screen

ez (Audio/Adjust Screen): Press this key toview the audio and screen settings.

Automatic Volume Control (AVC): With AVC,the audio system will adjust automatically to makeup for road and wind noise as you drive, byincreasing the volume as vehicle speed increases.

To use AVC, set the volume to your desiredlevel and then touch the ON screen button. Toturn AVC off, select the OFF screen button.

If your vehicle has Bose AudioPilot® noisecompensation technology, AudioPilot® monitorsthe level of noise in the vehicle and automaticallyincreases or decreases the level of the audioto keep it audible above the noise. This featureworks best at lower volume settings wherebackground noise may mask the audio. At highervolume settings, where the audio is muchlouder than the noise, there may be little or nochange in the audio level. For additionalinformation on AudioPilot®, please visitwww.bose.com.

To use this feature, set the volume to your desiredlevel and then touch the ON screen button. Toturn it off, select the OFF screen button.

Preset selection: This feature allows you toprogram local presets which you can recallby touching HOME. You may also program presetswhile you are traveling to another area andstore them under AWAY. See “Preset StationMenu” later in this section for more information.

The Home and Away feature is not availablefor XM™ Satellite Radio Service, if equipped.

83

Color Scheme: Select this feature to change thecolor of audio and navigation screens. Touchany of the color options to view the differentbackgrounds. Color option 1 is the default option.

ClockTouch the clock symbol at the bottom of theaudio/adjust screen or touch and hold the timedisplay in the upper right corner of any menuto access the CLOCK ADJUST menu. Touchingthe time display will also display the date onthe status bar at the top of the screen.

The following time options may be adjusted fromthis menu:

Hour/Min.: Touch the up or down arrows toincrease or decrease the hour or minutes. Touchand hold either arrow to advance quickly.

12H/24H: Touch 12H to display the time instandard time, or 24H to display the time inmilitary time.

GPS TIME: The current GPS time will bedisplayed to the right of this button. Touch GPSTIME to set the navigation system’s time to matchcurrent GPS time.

84

Daylight Saving Time: Touch this screen buttonto increase the time setting by one hour, thentouch GPS TIME to save the new setting. If thescreen button is light blue, the daylight savingstime feature is on. If the screen button is dark blue,the daylight savings time feature is off.

TIME ZONE: The selected time zone will appearto the right of this screen button. Touch TIMEZONE to toggle through the available time zonesuntil the desired time zone is highlighted. Thetime of the selected zone will be displayed to theright of GPS TIME. To set the system clock tothe new setting, touch GPS TIME.

If the system is not receiving GPS information,you can still set the time manually as describedabove, but GPS time and Daylight SavingTime features will not be available.

Touch the back screen button to go back to theprevious menu.

Screen AdjustTo adjust the contrast or brightness of the screen,touch SCREEN ADJUST at the bottom of theaudio/adjust screen.

The following screen options may be adjustedfrom this menu:

K (Contrast): Touch the plus (+) or minus (−)to adjust the contrast. You will see the screenchange. Touch OK to confirm the change.

85

! (Brightness): Touch the plus (+) or minus (−)to adjust the brightness. Touch OK to confirmthe change.

AUTO: This setting automatically adjusts thecontrast and brightness of the screen based onoutside lighting conditions.

DAY: This setting leaves the screen in day mode.Day mode is best suited for daylight conditions.

NIGHT: This setting leaves the screen in nightmode. Night mode is best suited for nighttimeconditions.

SCREEN OFF: Touch SCREEN OFF to turn offthe screen. Press the NAV, SRCE, ore/z(audio adjust) hard key to turn the screen back on.

OK: Touch OK to save the changes and exitthis menu.

SOUND: Touch SOUND to access the SOUNDmenu. See “Sound Menu” later in this sectionfor more information.

Finding a StationPress the SRCE hard key to display the operationscreen of the current audio source. Eachoperation screen has an audio source screenbutton, (AM, FM1, FM2, XM1, XM2, if equipped,and CD). Touch the desired audio source toselect it.

86

Preset Station MenuUp to 30 stations, 6 AM, 6 FM1, 6 FM2, 6 XM1,and 6 XM2, if equipped, can be programmedfor home and for away (XM does not havethe home and away feature). To store presets, dothe following:

1. Turn the audio system on.

2. Press the SRCE hard key.

3. Touch AM, FM1, FM2, XM1, or XM2, ifequipped, to display the desired source.The preset station menu will appear.

4. Tune to the desired station by using theTUNE/SEEK arrows.

5. Touch SOUND to set the bass, mid-range,treble, and Auto Tone Control (ATC) foryour preset, if desired. See “Sound Menu”later in this section for more information.

6. Touch and hold one of the six numberedpreset screen buttons for more thantwo seconds until you hear a beep.

7. Repeat the steps for each preset and source.

SCAN: To scan stations, touch SCAN. The radiowill go to a station, play for a few seconds,then go on to the next station. Touch SCAN againto stop scanning.

To scan preset stations, touch and hold SCAN fortwo seconds. It will only scan the audio sourceit is in, with the exception of FM 1 and FM 2, whichwill both be scanned if in that source. TouchSCAN again to stop scanning.

RDS (Radio Data System): See “Radio DataSystem (RDS)” later in this section for moreinformation.

Info (Information): See “Radio Data System(RDS)” later in this section for more information.

AutoSet: Touch this screen button to replacecurrently stored preset stations with the strongeststations available in the immediate area. Touchit again to return to the original preset stations.

SOUND: See “Sound Menu” following in thissection for more information.

87

Sound MenuTouch SOUND at the bottom of the main audioscreen or source menu to change the tone, ATC,fade, and balance for all sources. The audiosystem has a separate setting for these featuresfor each source preset. However, the audio systemkeeps one fade and one balance setting for allaudio sources.

To adjust sound settings, do the following:

• Touch the plus (+) or minus (−) signs to adjusttreble, mid-range, and bass, if you are in theManual mode of ATC.

• Touch the L (left) or R (right) to adjust thebalance of the speakers.

• Touch the F (front) or R (Rear) to adjust thefade of the speakers.

• Touch the ATC screen button to adjust theATC setting. See “Adjusting the Speakers”later in this section for more information.

After adjustments are made, touch the backscreen button. This will take you back to the presetstation menu. Whenever you touch that screenbutton, the previously stored information you haveentered for each preset station will be recalled.

88

Adjusting the Speakers

ATC (Auto Tone Control): The ATC feature isused to provide a choice of six different listeningexperiences. ATC can be used while listeningto the audio system or the CD player. The audiosystem can store separate ATC settings foreach source and preset station.

To save ATC settings for your preset stations,use the SOUND menu and touch ATC. See“Preset Stations” earlier in this section for moreinformation.

Radio Data System (RDS)The audio system has a Radio Data System(RDS). RDS features are available for use only onFM stations that broadcast RDS information.With RDS, the radio can do the following:

• Seek to stations broadcasting the selectedtype of programming

• Receive announcements concerning local andnational emergencies

• Display messages from radio stations

• Seek to stations with traffic announcements

RDS (Radio Data System): Touch RDS touse alternate RDS functions located in the presetmenu. When you touch RDS, you will onlyhave about five seconds to choose RDS ON/OFF,TA, INFO, PTY, or Select PTY. If you do notmake a selection, the system will return tothe previous menu.

89

If you are tuned to a station broadcasting RDSinformation, the station’s Program Service(PS) and Program Type (PTY) will replace thestation’s frequency on the status line at the top ofthe display. After about five seconds, if available,the PTY will be replaced on the display by thestation’s PTY name. The PTY and PTY name maybe the same or different.

If the audio system is tuned to a station that is notbroadcasting RDS information, the station’sfrequency will remain on the display.

The RDS feature relies upon receiving specificinformation from RDS stations. These features willonly work when RDS information is available.

TA (Traffic Announcement): Touch TA toreceive traffic announcements. The audio systemwill turn on the TA display. TA will appear onthe display if the current station broadcasts trafficannouncements. If the current station does notbroadcast traffic announcements, the audio systemwill seek to a station which will. When the audiosystem finds a station which broadcasts trafficannouncements, it will stop. If no station is found,TA will turn off.

While a traffic announcement plays, the audiosystem uses TA volume. To increase TA volume,use the VOL up or down buttons during theannouncement. See “Voice Guidance VolumeSettings” under Navigation Set Up on page 52 formore information.

When a traffic announcement comes on the currentradio station, you will hear it even if the volume ismuted or a CD is playing. If the CD player wasbeing used, the CD will stay in the player andresume play at the point where it stopped.

Touch RDS followed by TA again to turn TA off.

90

INFO (Information): When RDS is on, if thecurrent station has a message, INFO will appearon the display. Touch INFO from the presetmenu to view the message. If the whole messagedoes not appear on the display, parts of themessage will appear every three seconds until themessage is completed. Once the completemessage has been displayed, INFO will disappearfrom the display until another new message isreceived. INFO will remain available to allow youto display the entire message again.

PTY (Program Type): PTY allows you to seekonly stations with types of programs you wantto listen to. This button is used to turn on and offProgram Type (PTY) features.

With RDS on, touch RDS, followed by PTY. ThePTY display will turn on. Touch RDS followedby this button again to turn the PTY display off.

Select PTY (Select Program Type): With RDSand PTY on, touch RDS, then Select PTY.The PTY menu will appear. Use the up and downarrows to select a PTY.

When the PTY display is on, press TUNE/SEEKor SCAN to find radio stations of the PTY selected.The last PTY selected will be used for seek andscan modes. If a station with the selectedPTY is not found, STATION NOT FOUND willappear on the display. If both PTY and TA are on,the audio system will search for stations withtraffic announcements and the selected PTY.

PTY (Program Type) Presets: The six presetslet you return to your favorite PTYs. These presetshave factory PTY preset stations. See “RDSProgram Type (PTY) Selections” later inthis section. You can set up to 12 PTYs, 6 FM1and 6 FM2.

91

To save a PTY preset, do the following:

1. Touch FM1 or FM2.

2. Touch RDS to enter the RDS menu.

3. Touch RDS ON/OFF to turn RDS on.

4. Touch PTY.

5. Touch Select PTY and select the desiredPTY from the list.

6. Touch and hold one of the six presets formore than two seconds until you hear abeep. Whenever you touch that numberedpreset for less than two seconds, the PTYyou set will return.

7. Repeat the steps for each preset.

Once you have stored a PTY for each of yourpreset stations, you can recall a PTY presetby touching the preset station for less thantwo seconds. Then use TUNE/SEEK or SCAN tolocate a station for that PTY selection.

ALERT: This type of announcement warns ofnational or local emergencies. You will not be ableto turn off alert announcements. ALERT appears onthe display when an alert announcement plays. Theaudio system uses TA volume during theseannouncements. To increase volume, use the VOLup and down buttons during the announcement.See “Voice Guidance Volume Settings” underNavigation Set Up on page 52 for more information.When an alert announcement comes on the tunedradio station you will hear it even if the volume ismuted or a CD is playing. If the CD player isplaying, the player will stop for the announcementand resume when the announcement is finished.

92

XM™ Satellite Radio ServiceXM™ is a satellite radio service that is based inthe 48 contiguous United States and Canada.XM™ offers a large variety of coast-to-coastchannels including music, news, sports, talk,traffic/weather (U.S. subscribers), and children’sprogramming. XM™ provides digital qualityaudio and text information that includes song titleand artist name. A service fee is required inorder to receive the XM™ service. For moreinformation, contact XM™; In the U.S. atwww.xmradio.com or call 1-800-852-XMXM (9696)or in Canada at www.xmradio.ca or call1-877-GET-XMSR (438-9677).

INFO (Information): Touch INFO while in XM™mode to retrieve various pieces of informationrelated to the current song or channel. By touchingINFO, you may retrieve four different categories ofinformation that cycle through: Artist Name/Feature,Song/Program Title, Channel Category, and otherAdditional Information that may be broadcast onthat channel.

Additional Information messages may only beavailable at certain times or on certain programs.If an Additional Information message is beingbroadcast on the tuned channel, INFO will appearon the display.

Each of the four information types may havemultiple pages of text. To reach a category, touchINFO once and wait until the desired type isdisplayed. If there are multiple pages of text forthe information selected type, the radio willautomatically display all the pages for that type at arate of about one page every three seconds beforetiming out and returning to the default display.

XL (Explicit Language Channels): XL on theradio display, after the channel name, indicatescontent with explicit language. These channels, orany others, can be blocked at a customer’srequest, by calling 1-800-852-XMXM (9696).

93

XM Radio Messages

Radio Display Message Condition Action RequiredXM Updating Updating encryption code The encryption code in the receiver is being updated, and

no action is required. This process should take no longerthan 30 seconds.

No XM signal Loss of signal The system is functioning correctly, but the vehicle is in alocation that is blocking the XM™ signal. When you moveinto an open area, the signal should return.

Loading XM Acquiring channel audio(after 4 second delay)

The audio system is acquiring and processing audio andtext data. No action is needed. This message shoulddisappear shortly.

Channel Off Air Channel not in service This channel is not currently in service. Tune to anotherchannel.

Channel Unavail Channel no longeravailable

This previously assigned channel is no longer assigned.Tune to another channel. If this channel was one of thepresets, choose another channel for that preset button.

No Artist Info Artist Name/Feature notavailable

No artist information is available at this time on this channel.The system is working properly.

No Title Info Song/Program Title notavailable

No song title information is available at this time on thischannel. The system is working properly.

No CAT Info Category Name notavailable

No category information is available at this time on thischannel. The system is working properly.

Not Found No channel available forthe chosen category

There are no channels available for the category youselected. The system is working properly.

No Information No Text/Informationalmessage available

No text or informational messages are available at this timeon this channel. The system is working properly.

94

Radio Display Message Condition Action RequiredXM Theftlocked Theft lock active The XM™ receiver in the vehicle may have previously been

in another vehicle. For security purposes, XM™ receiverscannot be swapped between vehicles. If this message isreceived after having your vehicle serviced, check with yourdealer.

XM Radio ID Radio ID label (channel 0) If tuned to channel 0, this message alternate with the XM™Radio eight digit radio ID label. This label is needed toactivate the service.

Unknown Radio ID not known(should only be ifhardware failure)

If this message is received when tuned to channel 0, youmay have a receiver fault. Consult with your dealer.

Check XM Receiver Hardware failure If this message does not clear within a short period of time,the receiver may have a fault. Consult with your dealer.

CD PlayerTo load/eject a music CD, do the following:


2. Press the faceplate tilt hard key. This willopen the faceplate of the system.

3. Press the eject hard key with the CD symbol.If a CD is already loaded, the CD will ejectfrom the slot.

4. Gently remove the CD from the slot andreturn it to its case.

5. Insert the music CD into the slot. The systemwill pull the disc into the player.

6. Press and release the faceplate tilt hard keyto close the faceplate.

Whenever the faceplate is opened, a warningmessage will display reminding you to close thefaceplate as soon as possible.

95

Playing a CDOnce a music CD is loaded, the CD player menuwill appear on the display.

If the ignition or radio is turned off with a CD inthe player it will stay in the player. When theignition or radio is turned on, the CD will start toplay where it stopped, if it was the last selectedaudio source.

As each new track starts to play, the track numberwill appear on the display.

The CD player can play the smaller 3 inch (8 cm)single CDs with an adapter ring. Full-size CDsand the smaller CDs are loaded in the samemanner.

If playing a CD-R the sound quality may bereduced due to CD-R quality, the method ofrecording, the quality of the music that has beenrecorded, and the way the CD-R has beenhandled. There may be an increase in skipping,difficulty in finding tracks, and/or difficulty in loadingand ejecting. If these problems occur, check thebottom surface of the CD.

If the surface of the CD is damaged, such ascracked, broken, or scratched, the CD will not playproperly. If the surface of the CD is soiled, see“Care of Your CDs” in the Index of your vehicle’sowner manual.

If there is no apparent damage, try a knowngood CD.

Notice: If you add any label to a CD, insertmore than one CD into the slot at a time,or attempt to play scratched or damaged CDs,you could damage the CD player. Whenusing the CD player, use only CDs in goodcondition without any label, load one CD at atime, and keep the CD player and the loadingslot free of foreign materials, liquids, anddebris.

Do not add any label to a CD, it could get caughtin the CD player. If a CD is recorded on apersonal computer and a description label isneeded, try labeling the top of the recorded CDwith a soft marker instead.

If an error appears on the display, see “CDMessages” later in this section.

96

r (Play): Touch this button to begin playing a CD.

RANDOM: Touch this button to hear the tracks inrandom, rather than sequential, order. TouchRANDOM again to turn off random mode.

SCAN TRACKS: Touch this button to hear thefirst 10 seconds of each track on the disc.Touch this button again to stop scanning. TheCD will mute while scanning.

REPEAT TRACK: Touch this button to repeat theselected track.

r (Rewind): Touch this button to rewind quicklythrough a track selection.

j (Pause): Touch this button to pause CD play.Touch it again to resume play or touch theplay button.

[ (Forward): Touch this button to fast forwardquickly through a track selection.

¦O SEEK ¥: Touch the up arrow to seek tothe next selection on the CD. If playing the lasttrack of the disc, touching the up arrow will seek tothe first track of the disc. Touch the down arrowto seek to the previous selection on the CD.If playing the first track of the disc, touching thedown arrow will seek to the last track of thedisc. The sound will mute while seeking.

97

Using an MP3

MP3 FormatWhen creating an MP3 disc, the following is a listof guidelines. If the customer does not followthese guidelines when recording a CD-R(W), theCD may not play.

• ID3 tag information is displayed by the radio ifit is available. The radio supports ID3 taginformation v1.0 or v1.1. The radio will displaya filename, song name, artist name, albumname, and directory name.

• Maximum 32 characters, including spaces, ina file or folder name.

• Maximum number of folders is 500 with500 files with a maximum hierarchy ofeight folders. It is recommended to keep thedepth of folders to a minimum in order to keepdown the complexity and confusion in tryingto locate a particular folder during playback.

• Create a folder structure that makes it easy tofind songs while driving. Organize songs byalbums using one folder for each album. Eachfolder or album should contain 18 songsor less.

• The files can be recorded on a CD-R orCD-RW with a maximum capacity of 700MB.

• DVD with MP3 are not playable on this system.

• The radio will not play a mixed mode CD-R/RW, a disc recorded with both *.cda and*.mp3 files.

• The player will support a disc with multiplesessions, but it is not required that the disc befinalized. It is recommended to record the discall at once.

• Recording format mode 2 or mode 2XA withRomeo or Joliet file system is not supportedwith this player.

• All applicable Mode 1 recording formats aresupported.

• MPEG 2.5 is not supported with this player. Fileformats MPEG 1 and MPEG 2 with all bit rates(including variable) except less than 16kbps aresupported with this player.

• Long files or folder names or a combination of alarge number of files and folders may cause theplayer to be unable to play up to the maximumnumber of files or folders or affect the readingspeed and time to play.

98

Playing an MP3If playing a CD-R the sound quality may bereduced due to CD-R quality, the method ofrecording, the quality of the music that has beenrecorded, and the way the CD-R has beenhandled. There may be an increase in skipping,difficulty in finding tracks, and/or difficulty in loadingand ejecting. If these problems occur, check thebottom surface of the CD. If the surface of the CDis damaged, such as cracked, broken, orscratched, the CD will not play properly. If thesurface of the CD is soiled, see “Care ofYour CDs” in the Index of your vehicle’s ownermanual.

If there is no apparent damage, try a knowngood CD.

Notice: If you add any label to a CD, insertmore than one CD into the slot at a time,or attempt to play scratched or damaged CDs,you could damage the CD player. Whenusing the CD player, use only CDs in goodcondition without any label, load one CD at atime, and keep the CD player and the loadingslot free of foreign materials, liquids, anddebris.

Do not add any label to a CD, it could get caughtin the CD player. If a CD is recorded on apersonal computer and a description label isneeded, try labeling the top of the recorded CDwith a soft marker instead.

r (Play): Select this screen button to beginplaying the disc.

r (Reverse): Press and hold this screen buttonto reverse through the current track.

[ (Fast forward): Press and hold this screenbutton to fast forward through the current track.

99

j (Pause): Select this screen button to pauseplay. Select this button or the play button toresume play.

SCAN TRACKS: Select this screen button tohear the first 10 seconds of each track, inthe current folder. Press this button again to stopscanning.

RANDOM: Select this screen button to play thetracks, in the current folder, in random, rather thansequential, order. Select this button again toturn off random play.

REPEAT TRACK: Select this screen button torepeat the track currently playing. Press the buttonagain to turn off repeat play.

TRACK SELECT: Select this screen button todisplay the MP3 folder/file structure. Use theup/down arrows to scroll through the list. Selectthe folder or track to play. Press the 4 (return)screen button to go back to the main screen.

HOME: Select this screen button to allow you togo to the Home folder. This is the folder onthe disc which contains the current track playing.

# (Folder Up): Select this screen button togo to the previous folder.

rq (Seek): Press the up arrow to seek to thenext track on a disc. If playing the last track,pressing the up arrow will seek to the first track ofthe current folder.

Press the down arrow to go to the beginning of thecurrent track or to the previous track on a disc. Ifplaying the first track, pressing the down arrow willseek to the last track on the current folder.

100

Six-Disc CD ChangerIf your vehicle has the CD changer, you can playup to six discs continuously. Normal size discsmay be played using the trays supplied inthe magazine. The smaller discs (8 cm) can beplayed only with specially designed trays.

You must first load the magazine with CDs beforeyou can play a CD. Each of the six trays holdsone CD.

Load the trays from bottom to top, placing a discin the tray label side up. If you load a disclabel side down, the disc will not play and an errorwill occur. Repeat this procedure for loading upto six discs in the magazine.

Once you have loaded the discs into the magazine,slide the CD changer door open. Push themagazine into the changer in the direction of thearrow marked on top of the magazine.

101

Close the door by sliding it all the way to the right.When the door is closed, the changer will beginchecking for discs in the magazine. This willcontinue for up to one and a half minutes,depending on the number of discs loaded. Youmay hear noise, but this is normal. The CDchanger is initializing.

To eject the magazine from the player, slide theCD changer door all the way open. Press theEJECT button, located inside of the changer door,and the magazine will eject. Remember to keepthe door closed whenever possible to keep dirt anddust from getting inside the changer.

To eject CDs from the magazine, you must pushthe RELEASE switch on the bottom of themagazine to release the CDs.

Press the CD hard key to access the six-disc CDchanger screen. You can also use the system’sDVD player for single CD play once the map DVDis removed. See “CD/DVD Player” later in thissection for more information.

If no CD is loaded in the CD/DVD Player and youpress the CD hard key, the message “No CDloaded” will appear on the display.

CD Changer Screen

102

The numbered buttons, 1 through 6, represent theorder of the CDs loaded in the changer. If thereare only two CDs loaded, only buttons 1 and 2 willbe available to choose from.

r (Play): Touch this button to begin playing a CD.

RANDOM DISC: Touch this button to hear thetracks in random, rather than sequential, order onthe CD selected. Press the TUNE/SEEK hardkey to randomly seek through the tracks on thisCD. Touch RANDOM DISC again to turn offrandom play.

SCAN TRACKS: Touch this button to hear thefirst 10 seconds of each track on the selected CD.Touch this button again to stop scanning. TheCD will mute while scanning.

REPEAT TRACK: Touch this button to repeat thetrack on the selected CD. Touch this buttonagain to turn off repeated play.

r (Rewind): Touch this button to rewind quicklythrough a track selection.

j (Pause): Touch this button to pause CD play.Touch it again to resume play or touch theplay button.

RANDOM ALL: Touch this button to hear thetracks, on all of the loaded CDs in the CD changer,in random, rather than sequential order. Pressthe TUNE/SEEK hard key while RANDOM ALL ison to randomly seek within that CD. TouchRANDOM ALL again to turn off random play.

SCAN DISCS: Touch this button to hear the first10 seconds of first track on each loaded CD.Touch this button again to stop scanning. The CDwill mute while scanning.

REPEAT DISC: Touch this button to repeat theselected CD. Touch REPEAT DISC again toturn off repeat play.

[ (Forward): Touch this button to fast forwardquickly through a track selection.

103

«TUNE SEEK ª: Press the up arrow to seek tothe next selection on the CD. If playing the lasttrack of the CD, pressing the up arrow will seek tothe first track of the next CD. Press the downarrow to seek to the previous selection on the CD.If playing the first track of the CD, pressing thedown arrow will seek to the last track on theselected CD. The sound will mute while seeking.

RDS (Radio Data Systems): See “RadioData Systems (RDS)” under Navigation AudioSystem on page 82 for information on this button.

SOUND: See “Sound Menu” under NavigationAudio System on page 82 for information onthis button.

CD Changer ErrorsCD ERROR could be displayed for the following:

• The road is too rough. The CD should playwhen the road is smoother.

• The CD is dirty, scratched, wet, or not loadedlabel side up.

• The air is very humid. If so, wait about anhour and try again.

If any error occurs repeatedly or if an error cannotbe corrected, please contact your GM dealer.

104

Audio Steering Wheel Controls

If your vehicle has thisfeature, some audiocontrols can be adjustedat the steering wheel.They include thefollowing:

x w (Seek): Press the up or the down arrow togo to the next or to the previous radio stationand stay there. The radio will only seek stationswith a strong signal that are in the selected band.

While a CD is playing, press the up or thedown arrow to go to the next or previous track.

While playing a CD in the six-disc CD changer,press the up or the down arrow to go to the next orprevious track. If more than one CD is loaded,press the up arrow when on the last track of theCD to go to the first track on the next loaded CD.

While a CD is playing in the radio or the six-discCD changer, press and hold the up or thedown arrow to fast forward or reverse through thecurrent track. If the end or the beginning of thetrack is reached, the system will go to the next orprevious track. Release either arrow to stopfast forwarding or reversing.

+ − (Volume): Press the plus or minus button toincrease or to decrease the volume.

1–6 (Preset Screen Buttons): Press this buttonto play stations that are programmed on theradio preset screen buttons. The radio will onlyseek preset stations with a strong signal that are inthe selected band.

When more than one CD is loaded in the six-discCD changer, press this button to go to the nextloaded CD.

105

Radio Personalization with Homeand Away FeatureIf your vehicle has this feature, you can recall thelatest audio system settings as adjusted thelast time your vehicle was operated. This featureallows two different drivers to store and recalltheir own audio system settings. The settingsrecalled by the audio system are determined bywhich remote keyless entry transmitter (1 or 2) wasused to enter the vehicle. The number on theback of the remote keyless entry transmittercorresponds to driver 1 or to driver 2. The audiosystem settings will automatically adjust towhere they were last set by the identified driver.

Your audio system can store HOME andAWAY preset stations. HOME and AWAY presetstations allow you to use one set of presetradio settings in the area where you live, andanother set when you go out of town. That way,you will not need to reprogram your preset stationsevery time you travel.

To select HOME and AWAY preset stations, dothe following:

1. Touch the Audio hard key to enter the audioscreen.

2. Touch the HOME or AWAY button.The next time the audio system is turned on,the system will recall the last active presetselection.

When battery power is removed and later applied,you will not have to reset your home audiosystem preset stations because the audio systemremembers them. However, you will have toreset your away radio preset stations.

106

Voice Recognition ....................................... 108

Section 4 Voice Recognition

107

Voice RecognitionThe navigation system’s voice recognition allowsfor hands-free operation of navigation andaudio system features. Voice recognition can beused when the ignition is on or in ACC orwhen Retained Accessory Power (RAP) is active.

This feature only works if the map DVD isinserted. If you try to use voice recognition withoutthe map DVD inserted, the system will display“Please insert the navigation map DVD to use thevoice recognition feature.”

The system may not hear you or may hear theincorrect word with the windows open or theconvertible top down due to background noise.

To use voice recognition, do the following:1. Press this talk

symbol hard keyand release it whenyou hear a beep.The audio system,if on, will mute.

2. Clearly state one of the commands listed onthe following pages. For example, say “FM1.”

3. The system will tell you the command beingimplemented. For example, the system willsay “FM1 Radio” and change the audiosystem to the FM1 source.

You may end voice recognition by not speakingany commands. After about five seconds ofsilence, the system will automatically cancel voicerecognition.

At times, the system may not understand aspoken command. If this happens, try again. If aspoken command is not available, the systemwill provide feedback based on availability.

While using voice recognition, make sure to keepinterior noise levels to a minimum. Otherwise,the system might not recognize voice commands.

The system will only recognize commandsspoken in English.

108

Voice Recognition CommandsThe following list shows all of the voice commandsavailable for the navigation system with a briefdescription of each. Any words shown in squarebrackets are optional. If there are words shown inparentheses, choose one of the options. Touse the voice commands, refer to the instructionslisted previously.

Help CommandsThese commands are universal and will enableyou to use the help prompts available fromthe system.

Command Help/List: This command will enablethe system to provide the available commandsfor the navigation radio.

Cancel: This command cancels the voicerecognition function.

Radio Commands

Radio: This command will change the audiosystem to the next radio audio source.

AM: This command will change the audio systemto the AM audio source.

FM1: This command will change the audiosystem to the FM1 audio source.

FM2: This command will change the audiosystem to the FM2 audio source.

XM1: This command will change the audiosystem to the XM1 audio source.

XM2: This command will change the audiosystem to the XM2 audio source.

Power On, Audio On: These commands will turnthe system’s power on.

Power Off, Audio Off: These commands will turnthe system’s power off.

Seek Up: This command will cause the selectedaudio source to seek to the next strongeststation.

Seek Down: This command will cause theselected audio source to seek down to the nextstrongest station.

109

CD Player Commands

Track Up: This command will cause the CDplayer to skip to the next track.

Previous Track: This command will cause theCD player to go to the previous track.

Track Down: This command will cause the CDplayer to go to the beginning of the track or goto the previous track if the track has elapsednine seconds.

Screen Commands

Screen Day Mode, Day Mode On: Thesecommands will adjust the system’s screen settingto the day mode.

Screen Night Mode, Night Mode On: Thesecommands will adjust the system’s screen settingto the night mode.

Screen Auto Mode, Auto Mode On: Thesecommands will adjust the system’s screen settingto auto mode.

Screen Off: This command will turn the system’sscreen display off.

Position Commands

Current Position, Current Location, ShowCurrent Position, Show Current Location:These commands will cause the system to displaythe vehicle’s current location on the map screen.

Map: This command will cause the systemto display the map screen.

Map Commands

Zoom In: This command will cause the system tozoom in when on the map screen.

Zoom In Maximum: This command will causethe system to zoom in to the minimum availablemap scale when on the map screen.

Zoom Out: This command will cause the systemto zoom out when on the map screen.

Zoom Out Maximum: This command will causethe system to zoom out to the maximumavailable map scale when on the map screen.

Heading Up, Change to Heading Up: Thesecommands will cause the system to displaythe Vehicle Up heading when on the map screen.

110

North Up, Change to North Up: Thesecommands will cause the system to display theNorth Up heading when on the map screen.

Map Direction, Change Map Direction: Thesecommands will cause the system to changethe vehicle’s direction from North up to heading upor heading up to North up on the map screen.

Mark, Mark This Point: These commandswill cause the system to mark the location as amemory point while on the map screen.

Right Map Zoom In: This command will causethe system to zoom in on the right map whenin dual map mode.

Right Map Zoom In (Maximum/MinimumScale): This command will cause the system tozoom in to the minimum available map scaleon the right map when in dual map mode.

Right Map Zoom Out: This command will causethe system to zoom out on the right map whenin dual map mode.

Right Map Zoom Out (Maximum/MaximumScale): This command will cause the system tozoom out to the maximum available map scale onthe right map when in dual map mode.

Right Map [Change to] / [Show] North Up[Mode]: These commands will cause the system todisplay the North Up heading on the right mapwhen in dual map mode.

Right Map [Change to] / [Show] Heading Up[Mode]: These commands will cause the systemto display the Vehicle Up heading on the rightmap when on the map screen and in dualmap mode.

Right Map [Change Map] Direction: Thiscommand will cause the system to change fromNorth Up to Heading Up or from Heading Upto North Up.

[Show/Change to] Dual Map Mode: Thiscommand will cause the system to change themap display to dual map mode.

111

[Show/Change to] Single Map Mode: Thiscommand will cause the system to change themap display to single map mode.

[Change to] 3D Map [Mode]: This command willcause the system to change the map display tothe 3-dimensional map.

[Change to] 2D Map [Mode]: This command willcause the system to change the map display tothe 2-dimensional map.

Destination Commands

Home, Go Home: These commands will causethe system to enter the Home destination asa waypoint or final destination, if a homedestination has been stored.

Go to Starting Point, Previous Starting Point:These commands will cause the system toenter the last available starting point as a waypointor final destination.

[Go to] Previous Destination: This commandwill cause the system to enter the last availabledestination as a waypoint or final destination, ifone is available.

[Go to] Preset Destination [Number] (number):This command will cause the system to go tothe preset destination number. This presetdestination can be chosen as a waypoint or adestination. There must be a location stored inthe preset destination number that is chosen. Forexample, first store a location in PresetDestination 3. Say “Go to Preset Destination 3.”The system will go to Preset Destination 3and prompt you to choose it as a waypoint ordestination.

Add [to] Waypoint: This command will cause thesystem to add the current marked point as awaypoint. This command is used after the followingcommands have been used: Home, Go toStarting Point, Go to Previous Destination.

Enter Destination: This command will cause thesystem to add the current marked point as thefinal destination. This command is used after thefollowing commands have been used: Home,Go to Starting Point, Go to Previous Destination.

112

Guidance Commands

Repeat Guidance, Repeat Voice: Thesecommands will cause the system to repeat the lastavailable voice prompt guidance command if adestination has been set.

Louder: This command will cause the system toincrease the volume of the navigation voiceprompts.

Softer: This command will cause the system todecrease the volume of the navigation voiceprompts.

Voice Guidance Off: This command will causethe system to turn off the navigation voice promptsif a destination has been set.

Voice Guidance On: This command will causethe system to turn on the navigation voice prompts.

[Change to] Arrow (Guide/Guidance): Thesecommands will cause the system to changeto Arrow Guidance screen view in the GuidanceMenu if a destination has been set.

[Change to] Turn List (Guide/Guidance): Thesecommands will cause the system to change toTurn List Guidance screen view in the GuidanceMenu if a destination has been set.

[Change to] Freeway (Guide/Guidance): Thesecommands will cause the system to change toFreeway Guidance screen view in the GuidanceMenu if a destination has been set. This commandis only available if you are on a freeway.

[Change to] Intersection (Guide/Guidance):These commands will cause the system to changeto Intersection Guidance screen view in theGuidance Menu if a destination has been set. Thiscommand is only available when the next turn isless than 0.5 mile (800 m) away for city streets and2 miles (2 km) away for freeways.

Entire Route, Entire Rout Map, Route Overview:These commands will cause the system todisplay the entire route if a destination hasbeen set.

113

Reroute: This command will cause the system togenerate an alternate route to a set destinationwhile on a planned route.

Detour, Detour Entire Route: These commandswill cause the system to activate the detourfeature when driving a planned route.

Next Waypoint Map: This command will causethe system to display the map view of thenext waypoint location if one has been set.

(First/Second/Third/Fourth/Fifth) WaypointMap: This command will cause the systemto display the map view of the named waypointlocation if it has been set.

Destination Map: This command will cause thesystem to display the map view of the finaldestination location if one has been set.

Yes: This command will confirm system talkback.

No: This command will cancel a command.

(Delete/Cancel) Destination: This command willcause the system to cancel the currentdestination.

(Delete/Cancel) All Waypoints and Destination:This command will cause the system to cancelall currently set waypoints and the final destination.

Quick: This command will cause the system toselect the Quick route when a destination hasbeen set.

Normal: This command will cause the system toselect the Normal route when a destinationhas been set.

Short: This command will cause the system toselect the Short route when a destination hasbeen set.

114

Point of Interest (POI) CommandsThe following commands will cause the system todisplay icons if they are available on the mapscreen when the map scale is set to 1⁄2 mile (1 km)or less.

Automobile Commands• Auto Service And Maintenance, Auto Service,

Maintenance

• Automobile Club, Triple A

• Car Park

• Car Wash

• Gas Station, Gas

• Other Automotive

• Parking

• Parking Garage

• Parking Lot

• Rental Car Agency

Entertainment Locations• Amusement Park

• Botanical garden

• Campground

• Casino

• Cinema

• Golf Course

• Horse Racing

• Marina

• Museum

• National and State Parks

• Park & Recreation, Parks & Recreation

• Performing Arts

• Ski Resort, Skiing

• Speedway

• Sport Complex, Stadium

• Tourist Attraction

• Video Rental

• Winery

• Zoological garden

115

Financial and Government Offices• ATM

• Bank

• Business Facility

• City Hall

• Civic Center, Community Center

• Convention Center, Exhibition Center

• Court House

• Government Offices

• Higher Education, University, College

• Hospital

• Library

• Other Financial Services

• Police Station

• Post Office

• School

• City Center

Personal Services• Beauty and Barber Shops

• Dry Cleaning

• Health and Fitness Club

Restaurant Locations• American Restaurant, American Food

• Chinese Restaurant, Chinese Food

• Coffee House

• Continental Restaurant, Continental Food

• French Restaurant, French Food

• Ice Cream Parlor

• Italian Restaurant, Italian Food

• Japanese Restaurant, Japanese Food

• Mexican Restaurant, Mexican Food

• Other Restaurant, Other Food

• Restaurant, I’m Hungry

• Seafood Restaurant, Seafood

• Show Restaurant

• Thai Restaurant, Thai Food

116

Shopping Locations• Convenience Store

• Department Store

• Grocery Store

• Home and Garden

• Other Retail Store

• Pharmacy

• Shopping, Shopping Mall

• Specialty Food Store

Transportation• Airport

• Bus Station

• Ferry Terminal

• Historical Monument

• Hotel

• Park & Ride

• Rest Area, Rest Stop

• Tourist Information

• Train Station

POI Off: This command will cause the system toturn off POIs so they do not appear on the mapscreen.

117

✍ NOTES

118

AAddress ........................................................ 22Alpha-Numeric Keypad .................................. 19Audio Adjust Screen ...................................... 83Audio System ................................................ 82Auto Reroute ................................................. 74Avoid Area .................................................... 44

CCalibration ..................................................... 56Canadian Owners ........................................... 2Canceling Guidance ...................................... 13CD

Player ........................................................ 95Six-Disc Changer ..................................... 101

CD Changer Errors ..................................... 104CD Player ..................................................... 95Cleaning the Display ..................................... 15Coordinates ................................................... 34

DDatabase Coverage Explanations .................. 80Destination & Waypoint ................................. 46Destination and Waypoint .............................. 63Detour ........................................................... 61Display, Cleaning .......................................... 15Display route ................................................. 63

EEjecting the DVD Map Disc ........................... 68Emergency .................................................... 28Enter Destination ........................................... 20

FFinding a Station ........................................... 86Freeway Entrance/Exit ................................... 32

119

GGetting Started, Navigation .............................. 5Getting Started on Your Route ...................... 36Global Positioning System (GPS) .................. 76Guidance Volume ................................... 15, 59

HHard Keys ..................................................... 18Head-Up Display (HUD) ................................ 75Home ..................................................... 35, 48

IInstalling the DVD Map Disc ......................... 67Intersection ................................................... 31

MMap .............................................................. 27Map Adjustments ........................................... 68Map Appearance ........................................... 72Map Scales ................................................... 68Maps ............................................................ 67Memory Points ....................................... 29, 40

NNavigation

Getting Started ............................................ 5System Overview ......................................... 4Using the System ...................................... 18

120

OOrdering

Map DVDs ................................................. 79Overview, Navigation System .......................... 4Owners, Canadian .......................................... 2

PPhone Number .............................................. 33Playing a CD ................................................ 96Playing the Radio .......................................... 82Point of Interest (POI) ................................... 24Preset Destination .................................. 35, 49Preset Station Menu ...................................... 87Previous Destination ............................... 30, 49Problems with Route Guidance ..................... 78

QQuick POI Selection ...................................... 53

RRadio ............................................................ 82

Personalization with Home and AwayFeature ................................................. 106

Radio Data System (RDS) ............................ 89Region .......................................................... 21Regional Maps .............................................. 67Restore System Defaults ............................... 59Route Preferences ........................................ 62Route Preview ............................................... 65

121

SScrolling the Map .......................................... 69Search Condition ........................................... 60Setting Radio Station Presets .......................... 8Setting the Region, Entering an Address

and Point of Interest, and Storing a HomeDestination and Preset Destinations ............. 9

Setting the Search Area ................................ 68Setting the Time ............................................. 8Six-Disc CD Changer .................................. 101Sound Menu ................................................. 88Stored Locations ........................................... 14Symbols ........................................................ 69System Needs Service, If .............................. 79

TTouch-Sensitive Buttons ................................ 19Traveling Across Regions .............................. 74Two-Dimensional/Three-Dimensional

(2D/3D) View ............................................. 52

UUser Settings ................................................ 58Using an MP3 ............................................... 98Using Your Home or Preset Destinations ....... 13

VVehicle Positioning ........................................ 77Voice Recognition ........................................ 108Voice Recognition Commands ..................... 109

XXM Radio Messages ..................................... 94XM™ Satellite Radio Service ........................ 93

122

2007 Chevrolet Corvette Navigation System M...To set the region, do the following: 1. Press the...

Documents

Transcript of 2007 Chevrolet Corvette Navigation System M...To set the region, do the following: 1. Press the...