2005 Cadillac DeVille Navigation System M - Chevrolet · Ordering Map DVDs ... Touch the System...

Overview ........................................................ 1-1Overview .................................................. 1-2

Features and Controls ..................................... 2-1Features and Controls ................................ 2-2

Navigation Audio System ................................ 3-1Navigation Audio System ............................ 3-2

Voice Recognition ........................................... 4-1Voice Recognition ...................................... 4-2

Index .................................................................1

2005 Cadillac DeVille Navigation System M

GENERAL MOTORS, GM, the GM Emblem, CADILLAC,the CADILLAC Crest & Wreath, and the name DeVille areregistered trademarks of General Motors Corporation.

The information in this manual supplements the ownermanual. This manual includes the latest informationavailable at the time it was printed. We reserve theright to make changes in the product after that timewithout notice.

Keep this manual with the owner manual in the vehicle,so it will be there if it is needed while you are on theroad. If the vehicle is sold, leave this manual andthe owner manual with the vehicle.

Litho in U.S.A.Part No. 25769281 A First Edition ©2004 General Motors Corporation. All Rights Reserved.

ii

Overview .........................................................1-2Navigation System Overview ............................1-2Getting Started ...............................................1-4

Section 1 Overview

1-1

OverviewNavigation System Overview

1-2

A. BAND Key. See “Finding a Station” under NavigationAudio System on page 3-2.

B. CD Key. See Navigation Audio System on page 3-2or CD/DVD Player on page 3-22.

C. DVD Key. See “Playing a DVD” under CD/DVDPlayer on page 3-22.

D. TUNE/SEEK Key. See “Playing the Radio” underNavigation Audio System on page 3-2.

E. e Audio Key. See “Playing the Radio” underNavigation Audio System on page 3-2.

F. Power-Volume Knob. See “Hard Keys” under Usingthe Navigation System on page 2-2.

G. Navigation System ScreenH. REPEAT Key. See “Hard Keys” under Using the

Navigation System on page 2-2.I. MAP Key. See “Hard Keys” under Using the

Navigation System on page 2-2.J. ROUTE Key. See “Hard Keys” under Using the

Navigation System on page 2-2.K. SETUP Key. See “Hard Keys” under Using the

Navigation System on page 2-2.

L. X TILT Key. See “Hard Keys” under Using theNavigation System on page 2-2.

1-3

Getting StartedBefore you begin to operate the navigation system, readthis manual thoroughly to become familiar with it andto understand how the system works.

The navigation system allows you to do the following:

• Plan a route with provided turn-by-turn routeand map guidance with voice prompts.

• Select a destination using various methodsand choices.

• Receive broadcast announcements on traffic andemergency alert communications.

The information in the system may not always becomplete. Road conditions such as prohibited turns,detours, and construction zones, change frequently.It is important to consider whether you can followthe directions given by the system for the currentconditions.

When getting started, you may set the navigationsystem to your preference using various options.To do so, reference the following topics:

• To adjust screen appearance, language, clock, orother options, see “Playing the Radio” underNavigation Audio System on page 3-2.

• To adjust English/metric measurements, voiceguidance volume, or other navigation settings,see Setup Menu on page 2-4.

1-4

Features and Controls ......................................2-2Using the Navigation System ...........................2-2Setup Menu ...................................................2-4Plan Route ..................................................2-10Edit Memory Point ........................................2-10Edit Waypoint ...............................................2-14Edit Avoid Point/Area ....................................2-16Enter Destination ..........................................2-18Route Preference ..........................................2-27Maps ..........................................................2-30

Symbols ......................................................2-33Remote Keyless Entry System ........................2-38OnStar® System ...........................................2-38Global Positioning System (GPS) ....................2-39Vehicle Positioning ........................................2-40Problems with Route Guidance .......................2-41If the System Needs Service ..........................2-41Ordering Map DVDs ......................................2-41Database Coverage Explanations ....................2-41

Section 2 Features and Controls

2-1

Features and Controls

Using the Navigation SystemThis section presents basic information you will need toknow to operate the navigation system.

Use the keys located on each side of the navigationscreen, as well as the available touch-sensitive screenbuttons, to operate the system. See Navigation SystemOverview on page 1-2 for more information on location.

Once the vehicle is moving, various functions will bedisabled to reduce driver distraction.

Hard KeysThe following hard keys are located to the left of thenavigation screen:

BAND: Press the BAND key to access the band screenand switch between AM, FM1, FM2, XM1, XM2, andWX, if equipped. See “Finding a Station” underNavigation Audio System on page 3-2.

CD: Press the CD key to play a CD. The CD screenwill be displayed. See Six-Disc CD Changer onpage 3-18 or CD/DVD Player on page 3-22.

DVD: Press the DVD key to play a DVD. The DVDscreen will be displayed. See CD/DVD Player onpage 3-22.

y TUNE/SEEKz: Press the TUNE/SEEK up ordown arrows to go to the next or previous radio stationand stay there. See “Finding a Station” underNavigation Audio System on page 3-2.

e(Audio): Press the audio key to view the main audioscreen. See “Playing the Radio” under Navigation AudioSystem on page 3-2.

PWR-VOL (Power/Volume Knob): Press thepower/volume knob to turn the audio and navigationsystems on and off. Turn the knob to increase ordecrease the volume to the audio system.

The following hard keys are located to the right of thenavigation screen:

REPEAT: Press the REPEAT key to repeat the currentvoice guidance navigation prompt.

2-2

MAP: Press the MAP key to view the map screenshowing current vehicle position.

The map screen can also display the followinginformation:• North or Heading Up symbol. See Symbols on

page 2-33.• Map scale. See Maps on page 2-30.• Distance to destination• GPS symbol if GPS signal is not being received.

See Global Positioning System (GPS) onpage 2-39.

• Options you have selected for reaching your currentdestination

• Time• Radio band and presets

ROUTE: Press the ROUTE key to display the PLANROUTE menu. See Plan Route on page 2-10.

SETUP: Press the SETUP key to display the SETUPMENU. See Setup Menu on page 2-4.

TILTX: Press the TILT key to open the navigationsystem faceplate for loading or removing the map DVD,a video DVD, or an audio CD. This key can only beused while the vehicle is in PARK (P).

Alpha-Numeric KeypadLetters of the alphabet, symbols, punctuation, andnumbers, when available to you, will be displayed onthe navigation screen as an alpha or numeric keypad.The alpha keypad will be displayed when the systemneeds you to input a city or street name. You can alsotouch Char at the bottom of the alpha keypad toaccess the numeric keypad when inputting a houseaddress, punctuation mark, or other character.Touch A - Z to return to the alpha keypad.

All characters are touch-sensitive screen buttons.Touch a character to select it.

Select the space symbol to enter a space betweencharacters or the words of a name.

V (Backspace): Select the backspace symbol if youhave selected an incorrect character.

To make your name selections easier, the system willonly allow you to select a character which can follow thelast one entered. For example, if you enter Z, you wouldnot be allowed to follow it with T. The system willhighlight the available characters and darken theunavailable characters.

2-3

If you are unsuccessful when inputting a name, it mayneed to be selected differently. It is also possible that themap DVD database may not contain that informationor the correct search area has not been selected.See Database Coverage Explanations on page 2-41for more information.

Touch-Sensitive ButtonsTouch-sensitive buttons, or screen buttons, are locatedon the screen. When you have successfully selecteda screen button, a beep will sound. These buttons will behighlighted when a feature is available and dim whenthey are unavailable. There are also some toggle screenbuttons that will be light blue when active and darkblue when inactive.

Setup Menu

SETUP: Press the SETUP key located to the right ofthe navigation screen to access the SETUP MENU.

The SETUP MENU allows you to adjust such things asmap appearance, navigation settings, and voiceguidance volume.

2-4

Navigation Settings

This menu allows you to change the following optionsfor the navigation system:

Restore Default SettingsThis feature will automatically reset the system to thedefault values.

To restore the default settings, do the following:

1. Touch the Restore Default Settings screen button.

2. Touch Enter.

3. Touch Return to exit this menu.

System ConfigurationThis feature allows you to reconfigure the navigationsystem. If you begin to drive your vehicle duringthis procedure, the system will not be able to adjustthe position or direction of your vehicle.

Touch the System Configuration screen button to viewthe following choices:

Adjust Vehicle Position: To correct the position ofyour vehicle on the map or to change vehicle position,do the following:

1. Touch the Adjust Veh Position screen button.The system will display Position Adjustment.The vehicle location symbol and the scroll symbolwill appear on the map.

2. Use the scroll symbol and the zoom in/zoom outfeature to locate the vehicle position on the map.

3. Touch Enter to set the vehicle position. The systemwill display Position Adjustment and two arrows willappear on the map screen.

4. Touch the arrows to adjust the direction of thevehicle. As you touch the arrows, you will seethe vehicle symbol direction changing.

5. When you have set the vehicle to the correctdirection, touch Enter. Relocation Completewill be displayed.


2-5

Calibrate Vehicle Speed Signal: If there are tirepressure differences or if a spare tire is installed, thenavigation system will automatically recalibrate thesystem. You may also choose to calibrate it yourself bydoing the following:

1. Touch Start to begin calibration.


Display UnitsThis feature allows you to select either English or metricmeasurements to appear for distances on the map.Touch English or Metric to set the desired measurement.

Time to DestinationThis feature allows you to view the estimated time totravel from your current position to the destination, andto reset the average speed to factory default settings.Estimated travel time is based on calculated routeinformation and the vehicle’s average speed. Touch ONto turn this feature on, OFF to turn this feature off, orReset to restore vehicle speed default settings. With thisfeature on, the estimated travel time to destination willdisplay along with the distance to destination.

Quick POI (Point of Interest) Selection

This menu allows you to choose a point of interest(POI), such as gas stations, restaurants, hotels, etc. tobe displayed on the map screen. You can also set adestination to a specific POI.

2-6

Setting the Quick POI menuTo set the Quick POI list displayed on the map screen,do the following:

1. Select the category you would like to replace.

2. Select a Quick POI category from the Quick POIselection menu list. The system will return to theQuick POI selection screen when a POI is selected.

3. Touch Return to save the setting and returnto previous menu.

Displaying Quick POI IconsTo display POI icons of a category on the map screen,do the following:

1. Touch the map screen once.

2. Touch the POI button. The Quick POI Selection listwill be displayed.

3. Select a category type or touch List Categories OrAll Local POIs to display the icons of the selectedcategory on the map screen.

Removing Quick POI IconsTo remove POI icons from the map screen,do the following:

1. Touch the map screen once.

2. Touch the POI OFF screen button. The current POIicons will be removed from the map screen.

Setting a Destination Using Quick POIThis feature will allow you to choose a POI as yourdestination. To set a destination using a POI,do the following:

1. Touch the POI icon on the map screen that youwish to set as a destination.The selected icon will be surrounded by a blinkingbox, and the name of the icon will be displayed.You may also touch INFO to view the POI name,address, city, and phone number, if available.

2. Touch the ENT DEST screen button.If a final destination has already been entered, youcan add the POI as a waypoint. See Edit Waypointon page 2-14 for more information.

3. Touch Enter to start planning your route.

4. To start route guidance, touch Start or begin drivingthe vehicle. Route guidance will automatically beginafter a short distance.

If you wish to cancel the route you have just set,do the following:

1. Press the ROUTE hard key.

2. Touch the Route Preference screen button.

3. Touch the Cancel Route screen button.

4. Select YES to cancel or NO to continue.

2-7

Guidance Appearance

This menu allows you to set the guidance appearancescreen options. This screen is displayed on the mapwhile on a planned route. The current settings willappear as light blue.

Split Map: Select this feature to display the guidancescreen on the map at all times.

Full Screen: Select this feature to display the guidancescreen on the map when approaching a maneuver.

Turn List: Select this feature to have the guidancescreen display several upcoming turns. Directionalarrows, street name, and distance to the next turn willbe displayed. As you approach the next turn, the systemwill display a closer view of the upcoming maneuver.

Arrow: Select this feature to have the guidance screendisplay the next turn. A directional arrow, street name,and distance to the turn will be displayed. As youapproach the turn, the system will display a closer viewof the upcoming maneuver.

2D: Select this feature to display the guidance screenas a two-dimensional view.

3D: Select this feature to display the guidance screenas a three-dimensional view.

2-8

Map Appearance

This menu allows you to set the map appearance screenoptions. The current setting will appear as light blue.

2D: Select this feature to display the map as atwo-dimensional view.

3D: Select this feature to display the map as athree-dimensional view.

Set 3D Viewing Angle: This feature allows you toadjust the 3D viewing angle. To do so, do the following:

1. Touch 3D on the MAP APPEARANCE menu.

2. Touch Set 3D Viewing Angle.The map screen with the 3D viewing angle bar willbe displayed.

3. Touch the up or down arrows to set the viewing angle.

4. Touch Return to save your settings and to exit thismenu or touch Reset to restore the viewing angleto the default setting.

Voice Guidance Volume SettingsThis feature allows you to set the voice prompt volumelevel or to turn voice prompts on or off.

Set the voice prompt volume level by touching thenumbered buttons to increase or decrease the volumelevel. You may also choose to turn the voice prompts off.Then touch Return to save your setting and to returnto the SETUP MENU.

If a voice prompt is active while the audio systemis on, the audio system volume will decrease and thevoice prompt will be heard through the driver’s sidefront speaker.

Voice prompts will not be heard while using voicerecognition or while using the factory-installedphone system.

2-9

Plan Route

To plan a route, press the ROUTE key. The PLANROUTE menu will be displayed.

You may use one of several destination entry methodsto plan a route. See Enter Destination on page 2-18for more information.

Edit Memory Point

This feature allows you to store, delete, and editmemory points. Touch the Edit Memory Point screenbutton from the PLAN ROUTE menu to access the EDITMEMORY POINT screen.

You can store memory points in four different categories,personal, business, entertainment, and marked point.

2-10

Memory points are stored when you select eitherSTART or MARK when setting a destination on the mapor when you are storing destinations in memory.

A total of 60 locations can be stored. The last10 destinations entered will be stored under PreviousDestination. In addition, one memory point can be storedunder the Home category.

If all 60 stored points are entered, the system will notifyyou that there is no available storage left in memorypoints. A memory point must be removed before storingadditional memory points.

Registering Memory PointsTo store a memory point, do the following:

1. Select a category from the EDIT MEMORYPOINT menu.

2. Touch REGISTER.

3. Select a method for entering a destination. A mapwill appear displaying the memory point’s location.

4. If available, touch INFO to view the addressinformation for the memory point.

5. Touch Enter to store the point.

Editing Memory PointsThis feature allows you to edit the contents stored inmemory. The following options are available:

Icon Editing of a Memory PointEach memory point is displayed with a default icon.To edit an icon, do the following:

1. Select the category of the memory point.

2. Select the item you want to edit.

3. Touch the icon. The EDIT MEMORY POINTicon screen will appear.

4. Touch the icon you would like to use.The system will then return to the EDITMEMORY POINT menu.

5. Touch Return to go back to the previous screen.

You will see the new memory point icon on the map.

When selecting an icon, you can choose from18 different icons, three of which are sound icons.The same icon may be used for other memory pointsas well.

2-11

Name Editing of a Memory PointTo modify the name of a stored memory point,do the following:


2. Select the item you want to edit.

3. Touch the NAME screen button and use the alphakeypad to edit the name. Names may contain up to15 alpha and/or numeric characters.

4. Touch Return to go to the previous screen.

Moving Memory PointsTo move a memory point from one category to another,do the following:


2. Select the memory point you want to edit.

3. Touch CATEGORY. A list of categories will appear.The current category for the item will be highlightedand cannot be selected.

4. Touch the screen button for the category you wantthe memory point placed in. A pop-up window willappear displaying the change in category.


Adjusting a Memory PointTo relocate a memory point’s location, do the following:



3. Touch POSITION. A map screen with the positionof this memory point will appear.

4. Touch anywhere on the screen to activate the scrollfeature and relocate the memory point. See Mapson page 2-30.

5. Touch Enter to save the memory point’s newlocation.


Changing the Phone Number of aMemory PointTo edit or add the phone number of a memory point,do the following:



3. Touch PHONE and use the numeric keypad to editor add the number.

4. Touch the RETURN button to take you back to theprevious screen when you have finished.

2-12

Deleting Single Memory PointsTo delete a single memory point, do the following:

1. Press the ROUTE key.

2. Touch EDIT MEMORY POINT.


4. Touch DELETE.

5. Select the memory point you want to delete.A confirmation window will appear.

6. Touch YES to delete the memory point orNO to return to the previous menu.


Deleting All Memory PointsTo delete all of the memory points in a category,do the following:



3. Select the desired category.

4. Touch the DELETE ALL screen button.A confirmation window will appear.

5. Touch YES to delete the memory points orNO to return to the previous menu.


Edit CategoryTo edit the name of a category, do the following:



3. Select the category you want to edit.

4. Touch the EDIT CATEGORY screen button anduse the alpha keypad to edit the category name.The name can consist of up to 15 alpha and/ornumeric characters.


Marked PointA marked point is a memory point which has beenstored by selecting the MARK screen button whiletraveling on a planned route. You can also use the scrollfeature to plan a destination on the map after reachingthe destination, or by moving a memory point to amarked point category. See “Editing Memory Points”earlier in this section for more information.

2-13

Previous Destination MemoryEach time you select Start from the map screen, thatdestination will be stored as a memory point underPREVIOUS DESTINATION. This category will store upto 10 destinations.

When the Previous Destination category contains morethan 10 destinations, the system will remove theoldest destination stored and add the most recent oneselected to the list.

If you do not want a previous destination to be lost,you must move the destination into a memorypoint category. See “Moving Memory Points” earlier inthis section for more information.

Home MemoryThis memory point is stored by selecting Home from theEDIT MEMORY POINT screen. See “RegisteringMemory Points” earlier in this section and “Home” underEnter Destination on page 2-18 for more information.

Edit Waypoint

Waypoints are destinations you can set along the wayto your final destination. This feature allows you toadd, edit, and delete waypoints.

You may set up to five waypoints on the way to yourfinal destination.

To access the WAYPOINT menu, do the following:


2. Touch Edit Waypoint.

2-14

Adding a WaypointTo add a waypoint to your route, do the following:

1. Touch Add Waypoint.2. Enter a destination. See Enter Destination on

page 2-18.A map will appear showing the location of thewaypoint.

3. Touch Enter to add your waypoint.4. Touch the ADD screen button to insert the waypoint

in the desired order.5. The system will display the ROUTE INFORMATION

screen. From this screen, several options areavailable.

List: Touch List to view the waypoint on the map or tochange the order of the waypoints and final destination.To change the order, touch CHG ORDER, thentouch the blank screen button next to the destination toselect the order of the waypoints and final destination.Press the MAP key to view the destination andwaypoints on the map screen.

Delete: Touch Delete to delete a waypoint or thefinal destination. A confirmation window will appear.Touch YES to delete the point or NO to return tothe previous screen.

Delete All: Touch Delete All to delete all of thewaypoints and the final destination. A confirmationwindow will appear. Touch YES to delete all waypointsor NO to return to the previous screen.

Change: Touch Change to change the final destination.Enter a destination. See Enter Destination on page 2-18.

Add: Touch Add to add additional waypoints. Refer tothe steps for adding a waypoint listed previously inthis section.

Calculate: Touch Calculate to begin route calculation.This feature will only be available if the final destinationhas been set.

2-15

Editing a WaypointThis feature allows you to edit waypoints that havealready been set. To edit a waypoint, do the following:

1. Touch Edit Waypoint.

2. Touch the MAP key to view the destination locationon the map screen.

3. Touch CHANGE ORDER to change the order of thewaypoints and the final destination.You can also use the map scroll to change awaypoint from one location to another.

Deleting a WaypointTo delete a waypoint from your route, do the following:

1. Touch Delete Waypoint.

2. Select the waypoint you want to delete.A confirmation window will appear.

3. Touch YES to delete the waypoint or NO toreturn to the previous menu.

Edit Avoid Point/Area

From this menu you can register, edit, and delete anarea to be avoided while planning a route. These areascan also be saved so the system can automaticallyavoid them when planning a route.

To access the AVOID POINT/AREA menu,do the following:


2. Touch Edit Avoid Point/Area.

2-16

Registering an Avoid Point/AreaTo store an avoid point/area, do the following:

1. Touch Register Avoid Point/Area.

2. Enter a location. See Enter Destination onpage 2-18.

3. If desired, reduce or enlarge the area around thepoint you want to avoid by using the REDUCE orENLARGE screen buttons.If an avoid point cannot be avoided, the system willdisplay “Avoid Point and Area Stored. RouteMay Not Avoid the Avoid Point and Areas.”

4. Touch Enter to set the area as an avoid point area.When using the REDUCE or ENLARGE buttons, abox will appear to represent the area or an X willappear to represent the area avoided. When anavoid point is set, the square will appear as green.


Editing an Avoid Point/AreaTo edit an avoid point/area, do the following:

1. Touch Edit Avoid Point/Area. A list of avoidedpoints will appear.

2. Select the avoided point/area you want to change.A map of the avoided area will appear.

3. Use REDUCE or ENLARGE to edit the avoidedpoint.

4. Touch Enter to set your new avoided area.The system will display “Area Adjusted.”


Deleting an Avoid Point/AreaTo delete an avoid point/area, do the following:

1. Touch Delete Avoid Point/Area. A list of avoidedpoints will appear.

2. Select the avoided point/area you want to delete.

3. The system will ask you to confirm your selection.Touch Yes to delete the avoid point/area or Noto cancel.If Yes is selected, the area will no longer beavoided when traveling on a planned route.


2-17

Enter Destination

The DESTINATION menu will give you several ways toplan a route. Touch the Enter Destination screenbutton from the PLAN ROUTE menu to display theDESTINATION menu.

For destination entry methods listed on the second pageof the DESTINATION menu, touch the Next Page arrow.Touch the Prev. Page arrow to return to the first page.

To enter a destination, choose from one of thedestination entry methods following in this section.

After entering a destination, If available, the systemwill display up to three routes in a pop-up windowindicating the total mileage and time to destination foreach route. Select a route by touching NEXT. The mapwill display each route in a different color. The selectedroute will be highlighted in red.

To start route guidance, touch Start or begin drivingyour vehicle. Route guidance will automatically beginafter a short distance.

If you touch CHG ROUTE before touching Start, you willbe able to change route preferences. See RoutePreference on page 2-27 for more information.

When a route has been planned, it will be highlightedand a bulls-eye symbol will appear on the map to showyour final destination.

If you wish to cancel a route that has been set, see“Cancel Route” under Route Preference on page 2-27.

2-18

Easy Planning Route

With this destination entry method, you can select adestination using the scroll symbol on the map screen.See Maps on page 2-30.

To use this destination entry method, do the following:

1. Press the MAP key.

2. Touch the map screen twice for the scroll symbol toappear. Touch the map or drag the scroll symboltoward your destination.

3. Touch the map screen continuously to scrollthrough the map faster. The address of the locationon the map will appear at the top of the screen.If needed, use the zoom feature to locate yourdestination. See “Map Scales” under Mapson page 2-30 for more information.

4. Touch ENT DEST to set this location as yourdestination. You may also touch MARK to storethis location as a memory point.

5. Touch Enter to plan your route.

2-19

Address

This destination entry method allows you to input anaddress by providing the system with a house number,street name, and city. Select Street to begin enteringthe desired address.

To use this destination entry method, do the following:

1. Enter the street name using the alpha keypad.See “Alpha-Numeric Keypad” under Using theNavigation System on page 2-2 for moreinformation.

Do not include name extensions such as N. or Drive.For example, the street name N. Civic Center Driveshould be entered as Civic Center. As information isentered, the system will automatically search foravailable names, and List will become available.

2. Touch List to view name choices or continue tospell the street name to further reduce the numberof available items.

3. Once the street name has been selected, enter thehouse number using the numeric keypad.The system will list the house number range that isavailable for the street.

4. When you have finished entering the house number,touch Enter.If the house number and street address you enteredexists in more than one city on the DVD database,a list of cities will appear. You can select a cityfrom the list, or enter the city name by selecting City.As you begin to enter the city name, you canselect the desired city from the list which will appear,or continue to spell the city name to further reducethe number of available items.


2-20

All Points of Interest

This destination entry method allows you to choose adestination from the point of interest (POI) list. SelectingAll Points Of Interest from the DESTINATION menuwill bring up the alpha keypad. While inputting a POIor city name, the List option will become available.As information is entered, the system will search foravailable POI and city names based on the informationgiven. The system will supply a list of names to makea selection from when the choices are five or less.

You may search for a POI using the following threemethods:

• Touch NAME to type in a POI by name using thealpha key pad. As you type in a name, the systemwill search for an available match to your input.Select the desired POI.

• Select a POI by touching CATEGORY. Use thearrows to scroll through the categories listed.Select a category along with any appropriatesub-categories. If the list of available POIs for theselected category is too long, you may need to enterthe POI’s name or city.

• Select CITY, then type in the city you wish to selecta POI from. Choose a city from the list of cities thatwill appear. If the list of POIs for the selected cityis too long, enter the POI’s name or choose acategory.

While inputting a POI or city name, the List option willbecome available. Touch List to view the list ofname choices, or continue to spell the name to furtherreduce the list of available items.

2-21

The system will list all POIs available. You can sort byname using NAME SORT or touch DIST SORT tolist POIs by distance from your current location.

Select a location from the list. The system will showthe selected POI on the map. If available, a pop-upwindow will be displayed. Touch INFO to view the POI’sname, address, city, and phone number, if available.

Touch Enter to plan your route.

Memory Points

This destination entry method allows you to set amemory point as your destination. Each time you storea destination from the map screen, the destinationis stored under MARKED POINT. See Edit MemoryPoint on page 2-10 for more information.

2-22

You must have destinations stored as memorypoints to select from PERSONAL, BUSINESS,ENTERTAINMENT, or MARKED POINT. If youhave renamed the memory point category name(s),the name(s) will appear as you changed them.

To select a destination using this entry method,do the following:

1. Touch the Memory Points symbol.

2. Select a category.

3. Select a destination. Use the arrows to scrollthrough the memory points. They can be sorted bydate, name, distance, and icon.


Previous Destination

This destination entry method allows you to select adestination by choosing from a list of the last10 destinations entered into the system.

To select a previous destination, do the following:

1. Touch the Previous Destination symbol.

2. Touch the screen button next to the desireddestination to select it.Use the arrows if necessary to view the entire list ofprevious destinations.


2-23

Previous Starting PointThis destination entry method allows you to select thelast start point as your destination. To select theprevious start point as your destination, do the following:

1. Touch Previous Destination.

2. Touch the Previous Starting Point screen button.


Home

This destination entry method allows you to select adestination that has been previously stored as Home.To choose Home as your destination, do the following:

1. Touch the Home symbol.


2-24

Set by Map

This destination entry method allows you to select adestination by using the scroll symbol. To use thisfeature, do the following:

1. Touch the Set By Map symbol. Current vehicleposition will be shown on the map screen.

2. Use the scroll symbol to select the desireddestination. The zoom in and zoom out feature canbe used to assist you in finding the desired location.See “Map Scales” under Maps on page 2-30.


Freeway Entrance/Exit

This destination entry method allows you to selecteither a freeway entrance or an exit as a destination.To enter a freeway name, do the following:

1. Touch the Freeway Entrance/Exit symbol.2. Enter the freeway name using the alpha key pad.

Freeways sometimes have a name and a numberassociated with them which you may need torefer to when entering freeway information.Freeways are also referred to by their abbreviatednames. For example, Interstate 75 in the U.S.is selected by entering I-75.As you enter a freeway name, the List option willbecome available.

2-25

3. Touch List to view the list of available name choicesor continue to spell the name to further reduce the listof available items. The system will supply a list ofnames when the choice is five or less.If you are unsuccessful when inputting a name, thename may need to be input differently, the mapDVD database may not contain this information, orthe name may be misspelled.

4. Select a freeway from the list.

5. The ENTRANCE or EXIT options will appear.Choose ENTRANCE to select the entrance tothe freeway, or EXIT to select the exit ramp ofthe freeway.When either button is touched, it will give analphabetical list of freeway entrance and exit rampson the freeway you entered. You may touchDIST SORT to sort the list by distance from yourcurrent location, or NAME SORT to sort thelist by name.

6. Select the desired freeway entrance or exit from thelist. A map will appear with the destination shown.


Intersection

This destination entry method allows you to select adestination by inputting the intersecting roads you wishto travel to. To enter an intersection, do the following:

1. Touch the Intersection symbol.

2. Using the alpha keypad, enter the name of the firststreet in the intersection.

2-26

3. To view a list of choices, touch List or continue tospell the name to further reduce the list of availableitems. The system will display a list of theintersecting streets if the number of intersectingstreets is five or less.

4. Select the first street.

5. Now enter the second street name.

6. Select the second street name from the list ofintersecting streets. To view a list of choices,touch List or continue to spell the name to furtherreduce the list of available items. The systemwill display a list of intersecting streets if the numberof intersecting streets is five or less.If there are multiple intersections with the sametwo roads, the system will display a list of cities tochoose from. Choose a city from this list. A map withthe intersections for that city will appear.


Route Preference

To change your planning options, do the following:


2. Touch Route Preference.

2-27

The following options will be available from the ROUTEPREFERENCE menu:

Detour

This feature allows you to choose a distance inmiles/kilometers to detour. Select the detour distancedesired for residential roads and freeways.

The system will retain these settings for the next timeyou use Detour, unless you change them.

You may also touch Alternate to provide a new routethat does not use previously stored detour settings.

Touch Return to go back to the previous screen.

Route Setting

This feature allows you to display and change theplanning methods used each time you plan a route.With planning method options, you are able to select thefastest route based on time or distance, using onlymajor roads, toll roads, and using ferries based on thenavigation system’s information and informationcontained on the map DVD.

2-28

The following options will be available from the ROUTESETTING menu:

Minimize Time/Distance: The system will calculate thefastest route or shortest route possible. Choose Timefor the fastest route or Dist for the shortest route.

Use Major Roads: Choose Yes to calculate the bestroute using only major roads unless a route cannotbe found without the use of a secondary road.This selection will not always offer the shortest distanceor time to your destination.

Use Toll Roads: Choose Yes to calculate the bestroute using toll roads wherever possible. This selectionwill not always offer the shortest distance or time toyour destination.

Use Ferries: Choose Yes to calculate the best routeusing ferries when possible. This selection will notalways offer the shortest distance or time to yourdestination.

Display Whole RouteThis feature allows you to display your entire plannedroute. Total mileage and time to destination for theplanned route will be displayed on the map screen.Touch Return to go back to the previous menu.

Calculate RouteThis feature allows you to begin route calculation for theselected destination.

Cancel RouteIf you are traveling on a planned route and would like tocancel it, touch Cancel Route. The system will askyou to confirm by touching YES. Touch YES to confirmcancellation of your planned route or touch Return tokeep your planned route.

2-29

MapsThis section includes basic information you need toknow about the map database.

Regional MapsThe maps are stored on a DVD-ROM. The 48 contiguousUnited States and portions of Canada are contained onone disc. The U.S. map database includes interstatefreeways, state highways, country roads, and major andgeneral streets.

Refer to the “Navigation System Map Disc” manual toview the explanation of map coverage and detailedcity lists in each region. The map disc manual will be inyour map DVD case when the vehicle is deliveredfrom the factory.

When your vehicle is delivered from the factory, thedealer may have installed the map DVD. If the map DVDwas not installed in your vehicle when first purchased,do the following:

1. Turn the ignition on.

2. With the vehicle in PARK (P), press and hold theTILT key until a beep is heard. The system’sfaceplate will open.

3. If already loaded, the map DVD or a CD will ejectfrom the slot.

4. Load the map DVD into the slot by inserting itpartway. The system will pull it in.

5. Press and release the TILT key to close thefaceplate.

Notice: Shifting out of PARK (P) with the system’sfaceplate open will cause the faceplate to closeautomatically. This could cause damage to a CD,DVD or the system if it is partially loaded. Beforeshifting out of PARK (P), make sure that the DVD orCD is loaded properly. The vehicle must be shiftedback into PARK (P) to close the faceplate.

Once the map DVD is inserted correctly, you will havethe following two choices:

• LANGUAGE

• I AGREE

You can change the language at this time. See“Language” under Navigation Audio System on page 3-2for more information on choosing a language. Once alanguage has been selected, touch I AGREE toplan a route. The map will appear showing your currentvehicle position.

2-30

Setting the Search AreaTo determine or change the system’s search area,do the following:


2. Touch the Enter Destination screen button.

3. Touch Change underthe Search Areaheading. The systemwill display a mapwith each regionrepresented.

4. Select the desired region by touching theappropriate screen button to the left of theU.S. map. The name of the states or the countryincluded in the selected region will be displayedat the bottom of the screen and the regionwill be highlighted.

5. Touch Enter to set the region as the search area.


2-31

Map AdjustmentsThe system allows you to adjust the scale of view onthe map. The map will scroll automatically based on thedirection you are traveling.

Map Scales

To view a larger or smallerscale of the map, touchthe map scale arrows.

You may also adjust the scale of the map by touchingthe scale on the bar. The scale of a map can range from1/32 of a mile (0.05 km) to 128 miles (256 km).

Scrolling the Map

Touch anywhere on themap screen twice todisplay the scroll symbol.

Place your finger on the map screen in any directionoutside of the scroll symbol to scroll in that direction.The map will continue to scroll until you removeyour finger.

If your vehicle is in PARK (P), the system will initiallyscroll at a slower rate. The rate will increase if youcontinue to touch the map screen.

If your vehicle is in motion, there is one scroll speedand a limited distance to scroll. You must keep touchingthe map screen to scroll a longer distance.

If your vehicle icon becomes lost while scrolling, pressthe MAP key to show the vehicle’s current location.

You may also use the scroll feature to set a destination.See “Set by Map” under Enter Destination onpage 2-18.

2-32

SymbolsThe following symbols are the most common thatappear on a map screen.

Your vehicle is shown asthis symbol. It indicatesthe current positionand heading direction ofyour vehicle on the map.

This symbol will appear onthe map to show yourdestination after a routehas been planned.

See Enter Destination on page 2-18 for more informationon planning a route.

You will see this type ofsymbol on the mapwhen a waypoint hasbeen planned.

The waypoint symbol will be numbered from 1 through 5depending on how many waypoints have been set.See Edit Waypoint on page 2-14 for more informationon adding waypoints.

This symbol indicates thedistance to your finaldestination.

2-33

This symbol indicates thedistance and estimatedtravel time to yourfinal destination.The Estimated Travel Timefeature must be on forestimated travel time tobe displayed.

This symbol indicates themap with North up.

While in North up mode, North will always be at thetop of the map screen regardless of which directionthe vehicle is traveling.

This symbol indicatesthe map with the vehicletravel direction up, orHeading up.

The shaded triangle indicates North. While in Headingup mode, the direction your vehicle is traveling willalways be at the top of the map screen.

Touch either the North Up heading symbol or thevehicle Heading Up symbol to alternate betweensettings.

This symbol will appearwhen the navigationsystem is unable toreceive the GPS signal.

See Global Positioning System (GPS) on page 2-39 formore information.

2-34

When a point of interest(POI) or street addressname is too long tobe displayed, an arrowwill appear.

Touch the right or left arrow to scroll through theentire name.

This symbol indicatesthe position of thenext turn instruction.

While on a planned route,touch this symbol todisplay the DEST MAP,WHOLE, and TURN LISToptions.

With these options, you can do the following:

Dest (Destination) Map: This option allows you to viewthe final destination location. The destination’s nameor address will be displayed on the map screen.Touch Return when finished.

2-35

Whole: This option allows you to view the entireplanned route. The distance to destination will bedisplayed on the map screen. Touch Return whenfinished.

Turn List: This option allows you to view a step-by-steplisting of upcoming street names, the distance thatyou will travel on the road, and turns you will need tomake during your planned route.

After touching Turn List, the system may take sometime to create the list. The length of time will varydepending on the length of your route and the planningmethods you have selected.

2-36

The turn list will read from bottom to top. The bottomstreet name is the street you are currently on.The system automatically updates this screen as youmake each turn. You may also touch the scroll upand down arrows providing scroll is available.Touching the down arrow will bring you to your currentlocation. Touching the up arrow will give you upcomingstreets. At times, there may not be names availablefor entrance or exit ramps.

To avoid a turn, touch AVOID next to the turn you wantto avoid. You can use REDUCE or ENLARGE to editthe avoided point. Touch Reroute or press the MAP keyto calculate your new route.

Touch Return to view your current position and to turnthe turn list screen off.

Touch REROUTE or press the MAP key to calculate anew route.

Auto RerouteWhen your destination is set and you travel off of theplanned route, the system will automatically beginto reroute you. You will see the new route highlightedon the screen.

Traveling Across RegionsIf you plan to drive across several states, you may haveto change the selected region to represent the areayou are traveling to.

There are two ways you can plan a destination whentraveling across regions.

The following method is suggested and provides themost route guidance and map display functions:

1. Change the selected search area region whenyou get closer to the area you are traveling to.See “Setting the Search Area” under Mapson page 2-30.

2. Enter your destination and route settings.See Enter Destination on page 2-18for more information.

2-37

If you do not want to use the first method, keep yourcurrently selected search area region and enteryour destination. This method allows you only to selecta destination from the easy planning route methodor from the All Points of Interest (POI) categories withthe “All Search Areas” comment for US Only.For example, Tourist is a category that features thiscomment. See Enter Destination on page 2-18 for moreinformation.

If you are traveling in or to Canada and you cross theregional border, the only map scale views availableare 4 mi, 8 mi, 31 mi, and 128 mi (8 km, 16 km, 64 kmand 256 km). Change the selected search area regionwhen you get closer to the area you are traveling to.See “Setting the Search Area” under Maps on page 2-30for more information.

Remote Keyless Entry SystemWhen you insert the key in the ignition, Driver 1 orDriver 2 will be displayed on the screen. A message willnot appear on the screen if the driver is unknown.The number on the back of the RKE transmittercorresponds to driver 1 or driver 2. The navigationsystem can store memory points for drivers 1 and 2individually. See “Remote Keyless Entry Transmitter” inthe index of your vehicle’s owner manual for moreinformation.

OnStar® SystemWhen using the OnStar® system, the audio system willbe muted and the navigation voice prompts will bedisabled during the call. The volume of the OnStar® callcan be adjusted by using the steering wheel volumecontrols. See “Audio Steering Wheel Controls” and“OnStar® System” in the index of your vehicle’s ownermanual for more information.

2-38

Global Positioning System (GPS)The navigation system determines the position of yourvehicle by using satellite signals, various vehicle signals,and map data.

The Global Positioning System (GPS) locates thecurrent position of your vehicle using signals sent by theUnited States Department of Defense GPS satellites.While your vehicle is receiving signals from thesesatellites, the GPS symbol will not appear on themap screen.

However, at times, other interferences such as thesatellite condition, road configuration, the condition ofthe vehicle, and/or other circumstances can interferewith the system’s ability to determine the accurateposition of the vehicle. This is when the GPS symbolwill appear on the map screen.

This system may not be available or interferences mayoccur if any of the following are true:

• Signals are obstructed by tall buildings, largetrucks, or a tunnel.

• Objects are located on the rear shelf.

• Satellites are being repaired or improved.

• After-market glass tinting has been applied to thevehicle’s rear windshield.

Notice: Aftermarket glass tinting with metallicmaterial will interfere with the system’s ability toreceive GPS signals and cause the system tomalfunction. You might have to replace the rearwindow to correct the problem. The repairs wouldnot be covered by your warranty. Do not applyaftermarket glass tinting with metallic material tothe rear window of your vehicle.

If you are experiencing a problem, see VehiclePositioning on page 2-40 or Problems with RouteGuidance on page 2-41 for more information.

2-39

Vehicle PositioningAt times, the position of the vehicle on the map may beinaccurate due to one or more of the following reasons:

• The road system has changed.

• The vehicle is traveling on slippery road surfacessuch as sand, gravel, and/or snow.

• The vehicle is being driven on winding roads.

• The vehicle is being driven on a long straight road.

• The vehicle is approaching a tall building or a largevehicle.

• The surface streets run parallel to a freeway.

• The vehicle has just been transferred by a vehiclecarrier or a ferry.

• The current position calibration is set incorrectly.

• The vehicle is being driven at high speeds.

• The vehicle is repeating a change of direction bygoing forward and backward, or turning on a turntable in a parking lot.

• The vehicle is entering and/or exiting a parking lot orgarage with a roof.

• The vehicle has a roof carrier, ski, or bike rackinstalled on it.

• The vehicle has tire chains on it.

• The tires have been replaced.

• The tire pressure is incorrect.

• The tires are worn.

• The battery is disconnected.

• The vehicle is driven in heavy traffic where driving isat low speeds and the vehicle is stopped and startedrepeatedly.

2-40

Problems with Route GuidanceInappropriate route guidance may occur under any ofthe following conditions:

• You have not turned onto the road indicated bythe system.

• Route guidance is not available for the next turn.

• The route is not changed during automatic rerouting.

• Plural names of places are displayed.

• You are driving at high speeds, which may causethe automatic rerouting to operate more slowly.

• The route prohibits the entry of a vehicle due to aregulation by time or season or any other regulationwhich may be given.

• A route cannot be found.

• A road is new, was recently changed or is not listedon the DVD. The route to the destination may notbe shown. See Ordering Map DVDs on page 2-41.

If the System Needs ServiceIf you are still experiencing difficulty with your navigationsystem after reading this information, see your dealerfor assistance.

Ordering Map DVDsThe map DVD in your vehicle is the most up-to-dateinformation available when your vehicle was purchased.The map DVD is updated periodically, provided thatthe map information has changed. To order a new mapDVD, contact your dealer.

Database Coverage ExplanationsCoverage areas vary with respect to the level of mapdetail available for any given area. Some areas willfeature greater levels of detail than others. If thishappens, it does not mean there is a problem with thesystem. As the map DVD is updated, more detailmay become available for areas which previously hadlimited detail. See Ordering Map DVDs on page 2-41.

2-41

✍ NOTES

2-42

Navigation Audio System ..................................3-2Six-Disc CD Changer ....................................3-18CD/DVD Player ............................................3-22Radio Personalization with Home and

Away Feature ...........................................3-27

Section 3 Navigation Audio System

3-1

Navigation Audio SystemNotice: Before adding any sound equipment toyour vehicle, like a tape player, CB radio, mobiletelephone, or two-way radio, make sure that it can beadded by checking with your dealer. Also, checkfederal rules covering mobile radio and telephoneunits. If sound equipment can be added, it is veryimportant to do it properly. Added sound equipmentmay interfere with the operation of your vehicle’sengine, radio, or other systems, and even damagethem. Your vehicle’s systems may interfere with theoperation of sound equipment that has been addedimproperly.

Your vehicle has a feature called Retained AccessoryPower (RAP). With RAP, the audio system can beplayed even after the ignition is turned off. See“Retained Accessory Power (RAP)” in the index of yourvehicle’s owner manual for more information.

The audio system is operated using navigation systemmenus. The audio menus are explained in this section.

Playing the Radio

PWR-VOL (Power-Volume): Press this knob toturn the audio and navigation system on and off.Turn the knob to increase or decrease the volume tothe audio system.

e (Audio): Press this key to view the main audioscreen.

3-2

«TUNE/SEEKª: Press the up or down arrow to goto the next or previous station and stay there.

BAND: Press this key to switch between AM, FM1,FM2, XM1, and XM2, if equipped. If you are on a mapscreen and press this key, the menu will not change,but the audio source will.

Preset selection: This feature allows you to programlocal presets which you can recall by touchingHOME. You may also program presets while you aretraveling to another area and store them under AWAY.See “Preset Station Menu” later in this section formore information.

The Home and Away feature is not available for theXM™ Satellite Radio audio source, if equipped.

Display Presets on the Map: This feature allows youraudio system presets for the current audio source tobe displayed on the left of a map screen. Touch ON toturn this feature on. You may also choose to turnthis feature off.

Automatic Volume Control (AVC): If your vehicle hasthe Bose system, this feature allows your audiosystem to monitor noise in the vehicle. AVC willautomatically adjust the volume level so that it alwayssounds the same to you. To use AVC, touch ON.You may also choose to turn this feature off.

3-3

Clock

Touch the clock symbol at the bottom of the main audioscreen or touch and hold the time display in theupper right corner of any menu to get to the CLOCKADJUST menu. Touching the time display will alsodisplay the date.

The following time options may be adjusted fromthis menu:

HOUR/MIN.: Touch the up or down arrows to increaseor decrease the hour or minutes. Touch and hold anarrow to advance quickly.

12H/24H: Touch 12H to display the time in standardtime, or 24H to display the time in military time.

GPS TIME: The current GPS time will be displayed tothe right of this button. Touch GPS TIME to set thenavigation system’s time to match current GPS time.

Daylight Saving Time: Touch this screen buttonto increase the time setting by one hour, then touchGPS TIME to save the new setting. If the screen buttonis light blue, the daylight savings time feature is on.If the screen button is dark blue, the daylight savingstime feature is off.

TIME ZONE: The selected time zone will appear to theright of this screen button. Touch TIME ZONE totoggle through the available time zones and choose thedesired one. The time of the selected zone will bedisplayed to the right of GPS TIME. To set the systemclock to the new setting, touch GPS TIME.

If the system is not receiving GPS information, you canstill set the time manually as described above, butGPS time and Daylight Saving Time features will not beavailable.

Touch Return to go back to the previous menu.

3-4

Screen Adjust

To adjust the contrast or brightness of the screen,touch SCREEN ADJUST at the bottom of the mainaudio screen.

The following screen options may be adjusted fromthis menu:

K (Contrast): Touch the plus (+) or minus (−) toadjust the contrast. You will see the screen change.Touch SET to confirm the change.

!(Brightness): Touch the plus (+) or minus (−) toadjust the brightness. Touch SET to confirm the change.

AUTO: This setting automatically adjusts the contrastand brightness of the screen based on outsidelighting conditions.

DAY: This setting leaves the screen in day mode.Day mode is best suited for daylight conditions.

NIGHT: This setting leaves the screen in night mode.Night mode is best suited for nighttime conditions.

SCREEN OFF: Touch SCREEN OFF to turn off thescreen. Press any hard key to turn the screen back on.

SET: Press SET to save your choices and exitthis menu.

3-5

LanguageYour vehicle has been set for the English language.To adjust the language of your navigation system,do the following:

1. Touch the language, or globe symbol at the bottomof the main audio screen

2. Scroll up or down if necessary to select the desiredlanguage.


If the language is changed from English to a differentlanguage, the majority of voice guidance promptsand screen text will change to the selected language.Menu screens will not match word-for-word as theyappear in this manual.

If you accidentally select a language you do notunderstand, turn your engine off and open and closeyour door. Then, start the vehicle again and touchthe language symbol to select the correct language fromthe start-up screen.

Sound

SOUND: Touch SOUND to access the SOUND menu.See “Sound Menu” later in this section for moreinformation.

DSP

DSP (Digital Signal Processing): Touch DSP toaccess the DSP menu. See “Adjusting the Speakers”later in this section for more information.

3-6

Finding a Station

Press the BAND key to switch between AM, FM1, FM2,XM1, XM2, or WX, if equipped. Touch the desiredaudio source to select it.

Preset Station MenuUp to 36 stations, 6 AM, 6 FM 1, 6 FM 2, 6 XM 1,6 XM 2, and 6 WX, if equipped, can be programmed forhome and for away. To store presets, do the following:

1. Turn the audio system on.

2. Touch AM, FM, XM, or WX, if equipped, to displaythe desired source. The preset station menuwill appear.

3. Tune to the desired station by using theTUNE/SEEK arrows.

4. Touch SOUND to set the bass, mid-range, treble,and DSP for your preset, if desired. See “SoundMenu” later in this section for more information.

5. Touch and hold one of the six numbered presetbuttons for more than two seconds until you heara beep.

6. Repeat the steps for each preset and source.

FM1 source menu shown, other sources similar

3-7

SCAN: To scan stations, touch SCAN. The radio will goto a station, play for a few seconds, then go on to thenext station. Touch SCAN again to stop scanning.

To scan preset stations, touch and hold SCANfor two seconds. It will only scan the audio source it isin, with the exception of FM 1 and FM 2, which will bothbe scanned if in that source. Touch SCAN again tostop scanning.

RDS (Radio Data System): See “Radio Data System(RDS)” later in this section for more information.

MSG (Message): See “Radio Data System (RDS)” laterin this section for more information.

AutoSet: Touch AutoSet to replace currently storedpreset stations with the strongest stations available inthe immediate area. Touch AutoSet again to returnto the original preset stations.

SOUND: See “Sound Menu” following in this section formore information.

DSP: See “Adjusting the Speakers” later in this sectionfor more information.

Sound Menu

Touch SOUND at the bottom of the main audio screen,source menu, or DSP menu to change the tone,DSP, if equipped, fade, and balance for all sources.

3-8

The audio system has a separate setting for thesefeatures for each source preset. However, the audiosystem keeps one fade and one balance setting for allaudio sources.

To adjust sound settings, do the following:

1. Touch the plus (+) or minus (−) signs to adjusttreble, mid-range, and bass.

2. Touch the L for left or R for right to adjust thebalance of the speakers.

3. Touch the F for front or R for rear to adjust the fadeof the speakers.

4. Touch DSP to adjust your DSP, if equipped. See“Adjusting the Speakers” later in this section formore information.

After adjustments are made, touch any source screenbutton. This will take you back to the preset stationmenu. Whenever you touch that screen button,the previously stored information you have entered foreach preset station will be recalled.

To adjust the tone for each preset, do the following:

1. Press the BAND key.

2. Touch AM, FM1, FM2, XM1, XM2, or WX,if equipped, to access the desired preset screen.

3. Touch SOUND.

4. Touch the plus (+) or minus (−) signs to adjusttreble, mid-range, and bass.

5. Touch Return to exit. This will take you to thepreset station menu.

6. Touch and hold one of the six preset screenbuttons for more than two seconds until you heara beep.Whenever you touch that preset for less thantwo seconds, the station and previously storedinformation you have entered for each preset stationwill be recalled.

7. Repeat the steps for additional presets.

3-9

Adjusting the Speakers

DSP (Digital Signal Processing): If you have theBose system, the DSP feature is used to provide achoice of four different listening experiences. DSP canbe used while listening to the audio system or theCD player. The audio system can store separate DSPsettings for each source and preset station, except WX,which is always set to TALK.

To save DSP settings for your preset stations, use theSOUND menu or touch DSP from the preset stationmenu to access the DSP menu. See “Sound Menu”listed previously in this section for more information.

Touch DSP to change the following options:

ON/OFF: Touch ON/OFF to turn DSP on and off.

FRONT SEAT: Touch this button to adjust the audio togive the front seat occupants the best possible soundqualities.

TALK: TALK makes spoken words sound very clear.Touch this button when listening to non-musical materialsuch as news, talk shows, and sports broadcasts.

SPACIOUS: Touch this button to make the listeningspace seem larger.

AMBIENCE: Touch this button to enhance thestereo effect.

LEVEL: Touch the plus (+) minus (−) sign to increaseor decrease the level of the DSP effect after selecting aDSP setting.

SOUND: Press SOUND to access the Sound menu.See “Sound Menu” listed previously in this sectionfor more information.

3-10

Radio Data System (RDS)

The audio system has a Radio Data System (RDS).RDS features are available for use only on FM stationsthat broadcast RDS information. With RDS, the radiocan do the following:

• Seek to stations broadcasting the selected type ofprogramming

• Receive announcements concerning local andnational emergencies

• Display messages from radio stations

• Seek to stations with traffic announcements

RDS: Touch RDS to use alternate RDS functionslocated in the preset menu. When you touch RDS,you will only have about five seconds to choose RDSON/OFF, TA, MSG, PTY, or SEL PTY. If you donot make a selection, the system will return to theprevious menu.

If you are tuned to a station broadcasting RDSinformation, the station’s Program Service (PS) andProgram Type (PTY) will replace the station’s frequencyon the status line at the top of the display. After aboutfive seconds, if available, the PTY will be replacedon the display by the station’s PTY name. The PTY andPTY name may be the same or different.

If the audio system is tuned to a station that is notbroadcasting RDS information, the station’s frequencywill remain on the display. While RDS is on, theaudio system will search for a stronger station in thenetwork if a station gets too weak for listening.

The RDS feature relies upon receiving specificinformation from RDS stations. These features will onlywork when RDS information is available.

3-11

TA: Touch TA to receive traffic announcements.The audio system will turn on the TA display. TA willappear on the display if the current station broadcaststraffic announcements. You may also receive trafficannouncements from stations in the network related tothe current station. If the current station does notbroadcast traffic announcements, the audio system willseek to a station which will. When the audio systemfinds a station which broadcasts traffic announcements,it will stop. If no station is found, TA will turn off.

While a traffic announcement plays, the audio systemuses TA volume. To increase TA volume, touch the VOLbutton on your steering wheel or use the VOL up ordown buttons during the announcement. See “VoiceGuidance Volume Settings” under Setup Menu onpage 2-4 for more information.

When a traffic announcement comes on the currentradio station or a related network station, you will hear iteven if the volume is muted or a CD is playing. If theaudio system tunes to a related network station fora traffic announcement, it will return to the originalstation when the announcement is finished. If the CDplayer was being used, the CD will stay in the player andresume play at the point where it stopped.

Touch RDS followed by TA again to turn TA off.

MSG (Message): When RDS is on, if the currentstation has a message, MSG will appear on the display.Touch MSG from the preset menu to view the message.If the whole message does not appear on the display,parts of the message will appear every three secondsuntil the message is completed. Once the completemessage has been displayed, MSG will disappear fromthe display until another new message is received.MSG will remain available to allow you to display theentire message again.

3-12

PTY: PTY allows you to seek only stations with typesof programs you want to listen to. This button is used toturn on and off Program Type (PTY) features.

With RDS on, touch RDS, followed by PTY. The PTYdisplay will turn on. Touch RDS followed by thisbutton again to turn the PTY display off.

Select PTY (Select Program Type): With RDS andPTY on, touch RDS, then SEL PTY. The PTY menu willappear. Use the up and down arrows to select aPTY. Touch your PTY selection and the system willreturn you to the screen with the preset stations shown.See Steps 1 through 7 under “Preset Station Menu”to store the selected PTYs. The selected PTY is thenstored on the preset. You can now touch the PTY presetto recall your settings.

When the PTY display is on, press TUNE/SEEK andSCAN to find radio stations of the PTY selected. The lastPTY selected will be used for seek and scan modes.If a station with the selected PTY is not found, NONEFOUND will appear on the display. If both PTY and TAare on, the audio system will search for stations withtraffic announcements and the selected PTY.

PTY (Program Type) Presets: The six presets let youreturn to your favorite PTYs. These presets havefactory PTY preset stations. See “RDS Program Type(PTY) Selections” later in this section. You can set up to12 PTYs, 6 FM 1 and 6 FM2. To save a PTY preset,do the following:

1. Touch FM1 or FM2.

2. Touch RDS to enter the RDS menu.

3. Touch RDS ON/OFF to turn RDS on.

4. Touch PTY.

5. Touch SEL PTY and select the desired PTY fromthe list.

6. Touch and hold one of the six presets for morethan two seconds until you hear a beep. Wheneveryou touch that numbered preset for less thantwo seconds, the PTY you set will return.

7. Repeat the steps for each preset.

Once you have stored a PTY for each of your presetstations, you can recall a PTY preset by touchingthe preset station for less than two seconds. Then useTUNE/SEEK or SCAN to locate a station for thatPTY selection.

3-13

ALERT: This type of announcement warns of nationalor local emergencies. You will not be able to turnoff alert announcements. Alert announcements will comeon even if RDS mode is turned off. ALERT appearson the display when an alert announcement plays.The audio system uses TA volume during theseannouncements. To increase volume, touch theVOL button on your steering wheel or use the VOL upand down buttons during the announcement. See “VoiceGuidance Volume Settings” under Setup Menu onpage 2-4 for more information. When an alertannouncement comes on the tuned radio station or arelated network station, you will hear it even if thevolume is muted or a CD is playing. If the audiosystem tunes to a related network station for an alertannouncement, it will return to the original station whenthe announcement is finished. If the CD player isplaying, the player will stop for the announcement andresume when the announcement is finished.

XM™ Satellite Radio Service

XM™ is a satellite radio service that is based in the48 contiguous United States. XM™ offers 100 coast tocoast channels including music, news, sports, talk, andchildren’s programming. XM™ provides digital qualityaudio and text information, including song title and artistname. A service fee is required in order to receive theXM™ service. For more information, contact XM™ atwww.xmradio.com or call 1-800-852-XMXM (9696).

3-14

INFO (Information): Touch INFO while in XM™ modeto retrieve various pieces of information related tothe current song or channel. By touching INFO, you mayretrieve four different categories of information: ArtistName/Feature, Song/Program Title, Channel Category,and other Additional Information that may be broadcaston that channel. Additional Information messagesmay only be available at certain times or on certainprograms. If an Additional Information message is beingbroadcast on the tuned channel, INFO will appear onthe display.

Each of the four information types may have multiplepages of text. To reach a category, touch INFOrepeatedly until the desired type is displayed. If thereare multiple pages of text for the information selectedtype, the radio will automatically display all the pagesfor that type at a rate of about one page everythree seconds before timing out and returning to thedefault display. You may override this feature bytouching INFO to review all of the pages at yourown pace.

XL (Explicit Language Channels): XL on the radiodisplay, after the channel name, indicates content withexplicit language. These channels, or any others,can be blocked at a customer’s request, by calling1-800-852-XMXM (9696).

Setting Program Type (PTY) PresetStations

SCATT (Category): Press the arrows to selecta category.

Once the desired category is displayed, pressTUNE/SEEK to select the category and take you to thecategory’s first station. If you want to go to anotherstation within that category, press TUNE/SEEK once.

Touch and hold one of the desired P1-P6 presetsto store the selected station as a preset. If PTY timesout and is no longer on the display, start again.

SCAN: Use this button to scan through the channelswithin a category or scan through the preset stations.To scan through the channels in a category,do the following:

1. Select a category by using the category arrows.

2. Once the desired category is displayed, touchSCAN. The radio will begin scanning within thechosen category.

3. Touch SCAN again to stop scanning.

To scan through your preset stations, touch and holdSCAN. Touch SCAN again to stop scanning.

3-15

XM Radio Messages

Radio Display Message Condition Action Required

XM Updating Updating encryption code The encryption code in your receiver is being updated, andno action is required. This process should take no longerthan 30 seconds.

No XM signal Loss of signal Your system is functioning correctly, but you are in a locationthat is blocking the XM signal. When you move into an openarea, the signal should return.

Loading XM Acquiring channel audio(after 4 second delay)

Your radio system is acquiring and processing audio andtext data. No action is needed. This message shoulddisappear shortly.

Channel Off Air Channel not in service This channel is not currently in service. Tune in to anotherchannel.

Channel Unavail Channel no longeravailable

This previously assigned channel is no longer assigned.Tune to another station. If this station was one of yourpresets, you may need to choose another station for thatpreset button.

No Artist Info Artist Name/Featurenot available

No artist information is available at this time on this channel.Your system is working properly.

No Title Info Song/Program Titlenot available

No song title information is available at this time on thischannel. Your system is working properly.

No CAT Info Category Namenot available

No category information is available at this time on thischannel. Your system is working properly.

3-16

Radio Display Message Condition Action Required

Not Found No channel available forthe chosen category

There are no channels available for the category youselected. Your system is working properly.

No Information No Text/Informationalmessage available

No text or informational messages are available at this timeon this channel. Your system is working properly.

XM Theftlocked Theft lock active The XM receiver in your vehicle may have previously been inanother vehicle. For security purposes, XM receivers cannotbe swapped between vehicles. If you receive this messageafter having your vehicle serviced, check with the servicingfacility.

XM Radio ID Radio ID label(channel 0)

If you tune to channel 0, you will see this message alternatingwith your XM Radio 8 digit radio ID label.This label is needed to activate your service.

Unknown Radio ID not known(should only be ifhardware failure)

If you receive this message when you tune to channel 0,you may have a receiver fault. Consult with your dealer.

Check XM Receiver Hardware failure If this message does not clear within a short period of time,your receiver may have a fault. Consult with your retaillocation.

3-17

Six-Disc CD ChangerWith the compact disc changer, you can play up tosix discs continuously. Normal size discs may be playedusing the trays supplied in the magazine. The smallerdiscs (8 cm) can be played only with speciallydesigned trays.

You must first load the magazine with discs before youcan play a compact disc. Each of the six trays holdsone disc.

Load the trays from bottom to top, placing a disc in thetray label side up. If you load a disc label side down,the disc will not play and an error will occur. Repeat thisprocedure for loading up to six discs in the magazine.

Once you have loaded the discs into the magazine,slide the CD changer door open. Push the magazine intothe changer in the direction of the arrow marked ontop of the magazine.

3-18

Close the door by sliding it all the way to the right.When the door is closed, the changer will beginchecking for discs in the magazine. This will continuefor up to one and a half minutes, depending on thenumber of discs loaded. You may hear noise, but this isnormal. The CD changer is initializing.

To eject the magazine from the player, slide the CDchanger door all the way open. Press the EJECT button,located inside of the changer door, and the magazinewill eject. Remember to keep the door closed wheneverpossible to keep dirt and dust from getting inside thechanger.

To eject CDs from the magazine, you must push theRELEASE switch on the bottom of the magazineto release the CDs.

Press the CD hard key to access the six-disc CDchanger screen. You can also use the system’s DVDplayer for single CD play once the map DVD is removed.See “CD/DVD Player” later in this section for moreinformation.

If no CD is loaded in the CD/DVD Player and you pressthe CD hard key, the message “No CD loaded” willappear on the display.

3-19

Once you access the CD changer screen, you canselect one of the numbered buttons to go fromone compact disc to another among those loaded in theCD changer and use the arrows to rewind or fastforward through the disc selected.

The following features are also available from this screen:

• RANDOM DISC or RANDOM ALL,

• SCAN TRACKS or SCAN DISCS,

• and REPEAT TRACK or REPEAT DISC.

The numbered buttons, 1 through 6, represent the orderof the discs loaded in the changer. If there are onlytwo CDs loaded, only buttons 1 and 2 will be availableto choose from.

r (Play): Touch this button to begin playing a CD.

RANDOM DISC: Touch this button to hear the tracks inrandom, rather than sequential order on the discselected. Press the TUNE/SEEK hard key to randomlyseek through the tracks on this disc. Touch RANDOMDISC again to turn off random play mode.

SCAN TRACKS: Touch this button to hear the first10 seconds of each track on the selected disc. Touchthis button again to stop scanning. The CD will mutewhile scanning.

CD Changer Screen

3-20

REPEAT TRACK: Touch this button to repeat the trackon the selected disc. Touch this button again to turnoff the REPEAT TRACK mode.

r (Rewind): Touch this button to rewind quicklythrough a track selection.

j (Pause): Touch this button to pause CD play.Touch it again to resume play or touch the play button.

RANDOM ALL: Touch this button to hear the trackson all of the discs in the CD changer in random, ratherthan sequential order. Press the TUNE/SEEK hardkey while RANDOM ALL is on to randomly seek withinthat disc. Touch RANDOM ALL again to turn offrandom mode.

SCAN DISCS: Touch this button to hear the first10 seconds of first track on each disc. Touch thisbutton again to stop scanning. The CD will mutewhile scanning.

REPEAT DISC: Touch this button to repeat theselected disc. Touch REPEAT DISC again to turn offthe REPEAT DISC mode.

[ (Forward): Touch this button to fast forward quicklythrough a track selection.

«TUNE SEEKª: Press the up arrow to seek to thenext selection on the compact disc. If playing thelast track of the disc, pressing the up arrow will seek tothe first track of the next disc. Press the down arrowto seek to the previous selection on the compact disc.If playing the first track of the disc, pressing thedown arrow will seek to the last track on the selecteddisc. The sound will mute while seeking.

RDS (Radio Data Systems): See “Radio Data Systems(RDS)” listed previously for information on this button.

SOUND: See “Sound Menu (Tone, DSP, Fade andBalance)” earlier in this section for information onthis button.

DSP (Digital Signal Processing): See “Adjusting theSpeakers” listed previously for information on this button.

3-21

CD Changer ErrorsCD ERROR could be displayed for the following:

• The road is too rough. The disc should play whenthe road is smoother.

• The disc is dirty, scratched, wet or not loaded labelside up.

• The air is very humid. If so, wait about an hour andtry again.

If any error occurs repeatedly or if an error cannot becorrected, please contact your dealer. If your audiosystem displays an error number, write it downand provide this information to your dealer whenreporting the problem.

See “Glovebox-Mounted CD Changer” in your vehicle’sowner manual for more information.

CD/DVD PlayerThe player that is used for the navigation map DVD canalso be used as a single music CD player or a videoDVD player.

CD PlayerTo use the player as a single music CD player, youmust first remove the navigation map DVD. Whileplaying a CD in the CD/DVD Player, the navigationsystem is not available. The message “The disc installedis not a map DVD” will appear on the display if any ofthe navigation hard keys are pressed.

To remove the navigation map DVD and load amusic CD, use the following steps:

1. Turn the ignition to ON.

2. Press and hold the TILT hard key until you hear abeep. This will open the faceplate of the system.

3. If one is loaded, the navigation map DVD will ejectfrom the slot.

4. Gently remove the navigation map DVD from theslot and return it to its case.

5. Insert the music CD into the slot. The system willpull the CD into the player.

6. Press and release the TILT hard key to close thefaceplate.

3-22

Notice: Shifting out of PARK (P) with the system’sfaceplate open will cause the faceplate to closeautomatically. This could cause damage to aCD, DVD or the system if it is partially loaded.Before shifting out of PARK (P), make sure that theDVD or CD is loaded properly. The vehicle mustbe shifted back into PARK (P) to close the faceplate.

Once a music CD is loaded, the CD player menu willappear on the display. When using the system asa single CD player, the CD hard key will alternatebetween the CD player and the six-disc CD changer ifCDs are loaded.

r (Play): Touch this button to begin playing a CD.

RANDOM: Touch this button to hear the tracks inrandom, rather than sequential, order on the disc.Touch RANDOM again to turn off random mode.

SCAN TRACKS: Touch this button to hear the first10 seconds of each track on the disc. Touch this buttonagain to stop scanning. The CD will mute while scanning.

REPEAT TRACK: Touch this button to repeat theselected track.

r (Rewind): Touch this button to rewind quicklythrough a track selection.

j (Pause): Touch this button to pause CD play.Touch it again to resume play or touch the play button.

[ (Forward): Touch this button to fast forwardquickly through a track selection.

«TUNE SEEKª: Touch the up arrow to seek to thenext selection on the compact disc. If playing the lasttrack of the disc, touching the up arrow will seek to thefirst track of the disc. Touch the down arrow to seekto the previous selection on the compact disc. If playingthe first track of the disc, touching the down arrowwill seek to the last track of the disc. The sound willmute while seeking.

CD Player Screen

3-23

DVD PlayerTo use the player as a video DVD player, you must firstremove the navigation map DVD or music CD. Whileplaying a video DVD, the navigation system is notavailable. The message “The disc installed is not a mapDVD” will appear on the display if any of the navigationhard keys are pressed.

This feature will not operate unless the vehicle is inPARK (P).

To remove the navigation map DVD and load avideo DVD, use the following steps:

1. With the vehicle in PARK (P) and the ignition ON,press and hold the TILT hard key until a beep isheard. The faceplate of the system will open.

2. If a map DVD or a music CD is loaded, the systemwill automatically eject it. Gently remove it from theslot and return it to its case.

3. Load the video DVD into the slot. The system willpull the DVD into the player.

4. Press and release the TILT hard key to close thefaceplate.

Notice: Shifting out of PARK (P) with the system’sfaceplate open will cause the faceplate to closeautomatically. This could cause damage to aCD, DVD or the system if it is partially loaded.Before shifting out of PARK (P), make sure that theDVD or CD is loaded properly. The vehicle mustbe shifted back into PARK (P) to close the faceplate.

Once the faceplate is closed and a video DVD isloaded, the system will automatically play the DVD.

Playing a DVDThere are three ways to play a DVD depending onwhich screen you are on. They are the following:

• Once a DVD is inserted, the system willautomatically play the DVD.

• If you are on a map screen, touch the DVD sourcebutton.

• From the audio screen, press the DVD hard key.

3-24

DVD Menu OptionsTo display the menu choices while a DVD is playing,touch anywhere on the screen and the menu will appear.

IMAGE: Touch this button to either start playing a DVDor to remove the DVD menu screen.

AUDIO PROGRAM: Touch this button to change theaudio language heard.

VIEWING ANGLE: Touch this button to adjust theviewing angle of the DVD. Some DVDs allow you tochange the camera angle. This may not be availableon all DVDs. Depending on the type of DVD youare using, this button may or may not be available.

Subtitle: Touch this button to playback the video withsubtitles. This may not be available on all DVDs.Depending on the type of DVD you are using, this buttonmay or may not be available.

SCREEN ADJUST: Touch this button to adjust thebrightness, contrast and red/green color adjustments.

CURSOR: Touch this button to access the left/right andup/down cursors on the screen. The cursors allow youto navigate menu options on the screen.

MENU: Touch this button to access the DVDs menuoptions. Depending on the type of DVD you areusing, this button may or may not be available.Touch the button labeled one, two or blank to changethe image size displayed on the screen.

TITLE: Touch this button to display the title of theDVD. Depending on the type of DVD you are using,this button may or may not be available.

3-25

SETTING: Touch this button to adjust the following:

• LANGUAGE PREFERENCES

• PARENTAL LOCK

Under LANGUAGE PREFERENCES, you can selectdifferent languages for AUDIO, SUBTITLE andDVD MENUS.

1. To change languages, first select the option youwish to change.

2. Select a language from the list given.

3. Touch RETURN to end out the menu. Yourlanguage is now saved.

Under PARENTAL LOCK, you can select SET RATINGLIMIT and SET PIN.

To SET RATING, first touch the button. Then, makeyour selection. Touch RETURN to end out the menu.Your selection is now saved.

To use PARENTAL LOCK, first touch the button. Then,enter a four-digit numeric password. Touch RETURNto end out the menu.

SEARCH: Touch this button to search to a certainscene on the DVD. Depending on the type of DVD youare using, this button may or may not be available.

r (Rewind): Touch this button to rewind througha scene during playback.

r (Resume): Touch this button to resume playinga DVD.

c (Stop): Touch this button to stop the DVD.

j (Pause): Touch this button to pause the DVD.

[ (Forward): Touch this button to advance rapidlyduring playback.

L (Frame Advance): Touch this button to advance bychapter during playback.

3-26

Radio Personalization with Homeand Away FeatureIf your vehicle has this feature, you can recall the latestaudio system settings as adjusted the last time yourvehicle was operated. This feature allows two differentdrivers to store and recall their own audio systemsettings. The settings recalled by the audio system aredetermined by which remote keyless entry transmitter(1 or 2) was used to enter the vehicle. The numberon the back of the remote keyless entry transmittercorresponds to driver 1 or to driver 2. The audio systemsettings will automatically adjust to where they werelast set by the identified driver. The settings can alsobe recalled by briefly pressing the MEMORY seatswitches 1 or 2 located on the driver’s door.

Your audio system can store HOME and AWAY presetstations. HOME and AWAY preset stations allowyou to use one set of preset radio settings in the areawhere you live, and another set when you go out oftown. That way, you will not need to reprogramyour preset stations every time you travel.

To select HOME and AWAY preset stations,do the following:

1. With the audio system on, touch the Audiohard key and turn the audio system off.

2. Touch the HOME or AWAY button from thepreset screen.The next time the audio system is turned on, thesystem will recall the last active preset selection.

When battery power is removed and later applied, youwill not have to reset your home audio system presetstations because the audio system remembers them.However, you will have to reset your away radiopreset stations.

3-27

✍ NOTES

3-28

Voice Recognition ............................................4-2

Section 4 Voice Recognition

4-1

Voice RecognitionThe navigation system’s voice recognition allows forhands-free operation of navigation and audio systemfeatures. Voice recognition can be used when the ignitionis on or when Retained Accessory Power (RAP) is active.

This feature only works if the map DVD is inserted.If you try to use voice recognition without the map DVDinserted, the system will display “Please insert thenavigation map DVD to use the voice recognitionfeature.”

To use navigation voice recognition, do the following:

1. Press the talk symbolsteering wheel controland release it whenyou hear a beep.The audio system,if on, will mute.

2. Clearly state one of the commands listed on thefollowing pages. For example, say “FM1”.

3. The system will tell you the command beingimplemented. For example, the system willsay “FM1 Radio” and change the audio system tothe FM1 source.

END: Press this steering wheel control to end voicerecognition or to cancel a command. To cancel acommand, press END immediately after speaking thecommand. You will hear a beep confirming thecancellation.

You may also end voice recognition by not speakingany commands. After about five seconds of silence,the system will automatically cancel voice recognition.

At times, the system may not understand a spokencommand. If this happens, try again. If a spokencommand is not available, the system will providefeedback based on availability.

While using voice recognition, make sure to keepinterior noise levels to a minimum. Otherwise,the system might not recognize voice commands.

The system will only recognize commands spokenin English.

4-2

Voice Recognition CommandsThe following list shows all of the voice commandsavailable for the navigation system with a briefdescription of each. To use the voice commands,refer to the instructions listed previously.

Help CommandsThese commands are universal and will enable you touse the help prompts available from the system.

Map Help: This command will enable the system toprovide the available commands for the map screen.

Destination Help: This command will enable thesystem to provide the available commands for enteringa destination.

Guidance Help: This command will enable the systemto provide the available commands for the guidancemethod.

Radio Help: This command will enable the system toprovide the available commands for the radio.

Disc Help: This command will enable the system toprovide the available commands for the CD changer.

Radio Commands

Radio: This command will change the audio system tothe next radio audio source.

AM: This command will change the audio system to theAM audio source.

FM1: This command will change the audio system tothe FM1 audio source.

FM2: This command will change the audio system tothe FM2 audio source.

CD Changer: This command will change the audiosystem to the CD changer audio source.

WX, Weather Band: These commands will change theaudio system to the weather band audio source.

Power On, Audio On: These commands will turn thesystem’s power on.

Power Off, Audio Off: These commands will turn thesystem’s power off.

DSP On: This command will turn the audio system’sDSP on.

DSP Off: This command will turn the audio system’sDSP off.

4-3

DSP Front Seat: This command will change the audiosystem’s DSP to the front seat setting.

DSP Spacious: This command will change the audiosystem’s DSP to the spacious setting.

DSP Talk: This command will change the audiosystem’s DSP to the talk setting.

DSP Ambience: This command will change the audiosystem’s DSP to the ambience setting.

Seek Up: This command will cause the selected audiosource to seek up to the next strongest signal.

Seek Down: This command will cause the selectedaudio source to seek down to the next strongest signal.

Stop Scan: This command will cause the audiosource to stop scanning for the next strongest signal.

CD Changer Commands

Track Up: This command will cause the CD changer toskip up to the next track.

Previous Track, Track Down: This command willcause the CD changer to go to the previous track.

Phone Command

Phone: This command will activate the factory-installedoptional cellular phone system or OnStar® system.See the Cellular Phone System manual and “OnStar®

System” in Section 2 of your vehicle’s owner manual formore information.

Screen Commands

Screen Day Mode, Day Mode On: These commandswill adjust the system’s screen setting to the day mode.

Screen Night Mode, Night Mode On: These commandswill adjust the system’s screen setting to the night mode.

Screen Auto Mode, Auto Mode On: These commandswill adjust the system’s screen setting to auto mode.

Screen Off: This command will turn the system’sscreen display off.

4-4

Position CommandsCurrent Position, Current Location, Show CurrentPosition, Show Current Location: These commandswill cause the system to display the vehicle’s currentlocation on the map screen.

Map: This command will cause the system to displaythe map screen.

Map Commands

Zoom In: This command will cause the system to zoomin when on the map screen.

Zoom Out: This command will cause the system tozoom out when on the map screen.

Maximum Scale: This command will cause the systemto zoom out to the maximum available map scalewhen on the map screen.

Minimum Scale: This command will cause the systemto zoom in to the minimum available map scale whenon the map screen.

Heading Up, Change to Heading Up: Thesecommands will cause the system to display the VehicleUp heading when on the map screen. The map scaleshould be set for under 2 miles (4 km).

North Up, Change to North Up: These commandswill cause the system to display the North Up headingwhen on the map screen if the map scale is set to2 miles (4 km) or less.

Map Direction, Change Map Direction: Thesecommands will cause the system to change the vehicle’sdirection from North up to heading up or heading upto North up on the map screen if the map scale is set to2 miles (4 km) or less.

Mark, Mark This Point: These commands will causethe system to mark the location as a memory point whileon the map screen.

Destination Commands

Home, Go Home: These commands will cause thesystem to enter the Home destination, if one is set.

Go To Starting Point, Previous Starting Point:These commands will cause the system to enter thelast available starting point as a destination.

4-5

Guidance Commands

Repeat Guidance, Repeat Voice: These commandswill cause the system to repeat the last availablevoice prompt guidance command if a destination hasbeen set.

Louder: This command will cause the system toincrease the volume of the navigation voice promptsif a destination has been set.

Softer: This command will cause the system todecrease the volume of the navigation voice prompts ifa destination has been set.

Voice Guidance Off: This command will cause thesystem to turn off the navigation voice prompts ifa destination has been set.

Voice Guidance On: This command will cause thesystem to turn on the navigation voice prompts ifa destination has been set.

Open Guidance, Open Guidance Screen, OpenGuide, Open Guide Screen: These commands willcause the system to open the Guidance Appearancemenu if a destination has been set.

Close Guidance, Close Guidance Screen, CloseGuide, Close Guide Screen: These commandswill cause the system to close the Guidance Appearancemenu if a destination has been set.

Arrow Guidance, Arrow Guide, Change To ArrowGuidance, Change To Arrow Guide: These commandswill cause the system to change to Arrow Guidancescreen view in the Guidance Menu if a destination hasbeen set.

Turn List Guidance, Turn List Guide, Change toTurn List Guidance, Change to Turn List Guide:These commands will cause the system to change toTurn List Guidance screen view in the Guidance Menuif a destination has been set.

Entire Route, Entire Rout Map, Route Overview:These commands will cause the system to display theentire route if a destination has been set.

Reroute: This command will cause the system togenerate an alternate route to a set destination while ona planned route.

Detour, Detour Entire Route: These commands willcause the system to activate the detour featurewhen driving a planned route.

4-6

Delete Destination, Cancel Destination: Thesecommands will cancel a destination if one has been set.

Next Waypoint Map: This command will cause thesystem to display the map view of the next waypointlocation if one has been set.

First Waypoint Map: This command will cause thesystem to display the map view of the first waypointlocation if one has been set.

Second Waypoint Map: This command will cause thesystem to display the map view of the second waypointlocation if more than one waypoint has been set.

Third Waypoint Map: This command will cause thesystem to display the map view of the third waypointlocation if more than two waypoints have been set.

Fourth Waypoint Map: This command will cause thesystem to display the map view of the fourth waypointlocation if more than three waypoints have been set.

Fifth Waypoint Map: This command will causethe system to display the map view of the fifth waypointlocation if more than four waypoints have been set.

Destination Map: This command will cause the systemto display the map view of the final destination locationif one has been set.

Point of Interest (POI) CommandsThe following commands will cause the system to displayicons if they are available on the map screen when themap scale is set to a half mile (eight-tenths km) or less.

Restaurant, I’m Hungry: These commands will causethe system to display restaurant POI icons.

American Restaurant, American Food: Thesecommands will cause the system to display Americanrestaurant POI icons.

Chinese Restaurant, Chinese Food: Thesecommands will cause the system to display Chineserestaurant POI icons.

Continental Restaurant, Continental Food: Thesecommands will cause the system to display Continentalrestaurant POI icons.

French Restaurant, French Food: These commandswill cause the system to display French restaurantPOI icons.

Italian Restaurant, Italian Food: These commands willcause the system to display Italian restaurant POI icons.

4-7

Japanese Restaurant, Japanese Food: Thesecommands will cause the system to display Japaneserestaurant POI icons.

Mexican Restaurant, Mexican Food: Thesecommands will cause the system to display Mexicanrestaurant POI icons.

Seafood Restaurant, Seafood: These commandswill cause the system to display Seafood restaurant POIicons.

Other Restaurant, Other Food: These commands willcause the system to display other types of restaurantPOI icons.

Shopping, Shopping Mall: These commands willcause the system to display mall POI icons.

Grocery Store: This command will cause the systemto display grocery store POI icons.

Gas Station, Gas: These commands will cause thesystem to display gas station POI icons.

Parking Garage: This command will cause the systemto display parking garage POI icons.

Parking Lot: This command will cause the system todisplay parking lot POI icons.

Rental Car Agency: This command will cause thesystem to display rental car POI icons.

Automobile Club, Triple A: These commands willcause the system to display auto club POI icons.

Auto Service And Maintenance, Auto Service,Maintenance: These commands will cause the systemto display auto service POI icons.

Hotel: This command will cause the system to displayhotel POI icons.

Golf Course: This command will cause the system todisplay golf course POI icons.

Ski Resort, Skiing: These commands will cause thesystem to display ski resort POI icons.

Amusement Park: This command will cause thesystem to display amusement park POI icons.

Sport Complex, Stadium: These commands will causethe system to display sports complex POI icons.

4-8

Casino: This command will cause the system todisplay casino POI icons.

Marina: This command will cause the system to displaymarina POI icons.

Tourist Attraction: This command will cause thesystem to display tourist attraction POI icons.

Winery: This command will cause the system todisplay winery POI icons.

City Hall: This command will cause the system todisplay city hall POI icons.

Police Station: This command will cause the systemto display police station POI icons.

Library: This command will cause the system todisplay library POI icons.

Hospital: This command will cause the system todisplay hospital POI icons.

Park & Recreation, Parks & Recreation: Thesecommands will cause the system to display parks andrecreation POI icons.

Civic Center, Community Center: These commandswill cause the system to display community centerPOI icons.

Convention Center, Exhibition Center: Thesecommands will cause the system to display conventioncenter POI icons.

Court House: This command will cause the system todisplay court house POI icons.

Train Station: This command will cause the system todisplay train station POI icons.

Airport: This command will cause the system todisplay airport POI icons.

Bus Station: This command will cause the system todisplay bus station POI icons.

Commuter Rail Station: This command will cause thesystem to display commuter rail station POI icons.

Ferry Terminal: This command will cause the systemto display ferry terminal POI icons.

Park & Ride: This command will cause the system todisplay park & ride POI icons.

4-9

Rest Area, Rest Stop: These commands will causethe system to display rest area POI icons.

Tourist Information: This command will cause thesystem to display tourist information POI icons.

Historical Monument: This command will cause thesystem to display historical monument POI icons.

Performing Arts: This command will cause the systemto display performing arts POI icons.

Museum: This command will cause the system todisplay museum POI icons.

Bank: This command will cause the system to displaybank POI icons.

School: This command will cause the system todisplay school POI icons.

ATM: This command will cause the system to displayATM POI icons.

Higher Education, University, College: Thesecommands will cause the system to display highereducation POI icons.

Business Facility: This command will cause thesystem to display business facility POI icons.

City Center: This command will cause the system todisplay city center POI icons.

POI Off: This command will cause the system to turnoff POIs so they do not appear on the map screen.

4-10

AAudio System .................................................. 3-2Avoid Point/Area, Edit ...................................... 2-16

CCD

Six-Disc Changer ......................................... 3-18CD/DVD Player .............................................. 3-22

DDatabase Coverage Explanations ...................... 2-41

EEdit

Avoid Point/Area .......................................... 2-16Memory Point ............................................. 2-10Waypoint .................................................... 2-14

Enter Destination ............................................ 2-18

GGetting Started

Navigation .................................................... 1-4Global Positioning System (GPS) ...................... 2-39

KKeyless Entry System ...................................... 2-38

MMaps ............................................................ 2-30Memory Point, Edit ......................................... 2-10

NNavigation ................................................. 1-2, 1-4

Using the System .......................................... 2-2

1

OOnStar® System ............................................. 2-38Ordering

Map DVDs ................................................. 2-41

PPlan Route .................................................... 2-10Player

CD ............................................................ 3-22DVD .......................................................... 3-22

Problems with Route Guidance ......................... 2-41

RRadio ............................................................. 3-2

Personalization with Home andAway Feature .......................................... 3-27

Remote Keyless Entry System .......................... 2-38Route Preference ............................................ 2-27

SSetup ............................................................. 2-4Setup Menu ..................................................... 2-4Six-Disc CD Changer ...................................... 3-18Symbols ........................................................ 2-33System Needs Service, If ................................. 2-41System Overview

Navigation System ......................................... 1-2

VVehicle Positioning .......................................... 2-40Voice Recognition ............................................. 4-2

WWaypoint, Edit ................................................ 2-14

2

2005 Cadillac DeVille Navigation System M - Chevrolet · Ordering Map DVDs ... Touch the System...

Documents

Transcript of 2005 Cadillac DeVille Navigation System M - Chevrolet · Ordering Map DVDs ... Touch the System...