2000 GMC Sierra2000 GMC Sierra Owner's Manual ... Manual Transmission Operation Four-Wheel Drive...

421

Transcript of 2000 GMC Sierra2000 GMC Sierra Owner's Manual ... Manual Transmission Operation Four-Wheel Drive...

i

2000 GMC SierraOwner's Manual

Litho in U.S.A.Part Number X2015 A First Edition

© Copyright General Motors Corporation 1999All Rights Reserved

ii

Table of Contents

Keys and Door LocksKeyless Entry System (If Equipped) TailgateAutomatic TransmissionManual Transmission OperationFour-Wheel Drive Operation (If Equipped)Parking BrakeWindowsTilt Wheel (If Equipped) Turn Signal/Multifunction Lever

Windshield WipersCruise ControlInterior and Exterior LampsMirrorsStorage CompartmentsAccessory Power OutletsOnStar® System (Option)Instrument Panel, Warning Lights and GagesMessage CenterOil Life

Seats and Seat ControlsSafety Belts

Air Bag SystemChild Restraints

Section 1

Section 2

Seats and Restraint Systems

Features and Controls

iii

Section 3

Comfort Controls and Audio Systems

Section 4

Your Driving and the Road

Section 5

Table of Contents (cont'd)

Braking/Anti-lock BrakesSteeringDriving Tips for Various Road ConditionsOff-Road Driving

Recreational Vehicle TowingLoading Your VehicleTowing a Trailer

Heating and Air ConditioningSetting the Radio Clock

Radio/Cassette Player/CD PlayerRadio Theft-Deterrent Feature (If Equipped)

Hazard Warning FlashersJump StartingTowing Your Vehicle

Engine OverheatingChanging a Flat TireIf You're Stuck

Problems on the Road

iv

FuelChecking Fluids and LubricantsPassenger Compartment Air Filter (If Equipped)Bulb ReplacementWindshield Wiper Blade Replacement

Tires and WheelsAppearance CareElectrical System/Fuses and Circuit BreakersCapacities and SpecificationsNormal Maintenance Replacement Parts

Table of Contents (cont'd)

Maintenance Schedule

Service and Appearance Care

Section 7

Section 6

Scheduled MaintenancePeriodic Maintenance Inspections

Recommended Fluids and LubricantsMaintenance Records

v

Table of Contents (cont'd)

Customer Assistance Information

In the Index you will find an alphabetical listing of almost every subject in this manual. You can use it to quickly find something you want to read.

Section 8 Customer Satisfaction ProceduresCustomer Assistance OfficesRoadside Assistance and Courtesy Transportation

Warranty Information (See Warranty Manual)Reporting Safety Defects on page 8-10Service Publications

IndexSection 9

Please refer to the last page of this manual for your Service Station Guide

yellowblue

vi

GENERAL MOTORS, GM, the GM Emblem, GMC,the GMC Emblem and the name SIERRA are registeredtrademarks of General Motors Corporation.

This manual includes the latest information at the time it was printed. We reserve the right to make changes in the product after that time without further notice. For vehicles first sold in Canada, substitute the name“General Motors of Canada Limited” for GMCwhenever it appears in this manual.

Please keep this manual in your vehicle, so it will bethere if you ever need it when you’re on the road. If yousell the vehicle, please leave this manual in it so the newowner can use it.

We support voluntarytechnician certification.

For Canadian Owners Who Prefer aFrench Language Manual:Aux propriétaires canadiens: Vous pouvez vousprocurer un exemplaire de ce guide en français chezvotre concessionaire ou au:

DGN Marketing Services Ltd.1577 Meyerside Dr.Mississauga, Ontario L5T 1B9

yellowblue

vii

How to Use this ManualMany people read their owner’s manual from beginningto end when they first receive their new vehicle. If youdo this, it will help you learn about the features andcontrols for your vehicle. In this manual, you’ll find that pictures and words work together to explain things quickly.

Safety Warnings and SymbolsYou will find a number of safety cautions in this book.We use a box and the word CAUTION to tell you about things that could hurt you if you were to ignorethe warning.

CAUTION:

These mean there is something that could hurtyou or other people.

In the caution area, we tell you what the hazard is. Thenwe tell you what to do to help avoid or reduce thehazard. Please read these cautions. If you don’t, you orothers could be hurt.

yellowblue

viii

You will also find a circlewith a slash through it inthis book. This safetysymbol means “Don’t,”“Don’t do this” or “Don’tlet this happen.”

Vehicle Damage WarningsAlso, in this book you will find these notices:

NOTICE:

These mean there is something that coulddamage your vehicle.

In the notice area, we tell you about something that candamage your vehicle. Many times, this damage wouldnot be covered by your warranty, and it could be costly.But the notice will tell you what to do to help avoid the damage.

When you read other manuals, you might seeCAUTION and NOTICE warnings in different colors orin different words.

You’ll also see warning labels on your vehicle. They usethe same words, CAUTION or NOTICE.

yellowblue

ix

For example,these symbolsare used on anoriginal battery:

CAUTIONPOSSIBLE

INJURY

PROTECTEYES BY

SHIELDING

CAUSTICBATTERY

ACID COULDCAUSEBURNS

AVOIDSPARKS OR

FLAMES

SPARK ORFLAMECOULD

EXPLODEBATTERY

These symbolsare importantfor you andyour passengerswhenever yourvehicle isdriven:

DOOR LOCKUNLOCK

FASTENSEAT

BELTS

POWERWINDOW

AIR BAG

These symbolshave to do withyour lamps:

MASTERLIGHTING

SWITCH

TURNSIGNALS

PARKINGLAMPS

HAZARDWARNINGFLASHER

DAYTIMERUNNING

LAMPS

FOG LAMPS

These symbolsare on some ofyour controls:

WINDSHIELDWIPER

WINDSHIELDWASHER

WINDSHIELDDEFROSTER

REARWINDOW

DEFOGGER

VENTILATINGFAN

These symbolsare used onwarning andindicator lights:

ENGINECOOLANT

TEMP

BATTERYCHARGING

SYSTEM

BRAKE

COOLANT

ENGINE OILPRESSURE

ANTI-LOCKBRAKES

Here are someother symbolsyou may see:

FUSE

LIGHTER

HORN

SPEAKER

FUEL

Vehicle SymbolsThese are some of the symbols you may find on your vehicle.

yellowblue

x

Model ReferenceThis manual covers these models:

Regular Cab Pickup

Extended Cab Pickup

Chassis Cab

For

a More Detailed Look at

What's Under the HoodSee Section 6

Service Station Guide

Oil ViscosityEngine Oil

See Section 6

Engine Oil DipstickSee Section 6

FuelUse unleaded gas only,

87 Octane or higher. See Section 6

Cooling SystemSee Section 5

Hood ReleaseSee Section 6

Windshield Washer Fluid

See Section 6

Tire PressureSee Section 6

Spare Tire PressureSee Section 5

Alternate Fuel Door Release

See Section 6

BatterySee Section 6

Remote FuelDoor ReleaseSee Section 6

1-

yellowblue

1-1

Section 1 Seats and Restraint Systems

Here you’ll find information about the seats in your vehicle and how to use your safety belts properly. You can alsolearn about some things you should not do with air bags and safety belts.

1-2 Seats and Seat Controls1-11 Safety Belts: They’re for Everyone1-15 Here Are Questions Many People Ask About

Safety Belts -- and the Answers1-16 How to Wear Safety Belts Properly1-16 Driver Position1-23 Safety Belt Use During Pregnancy1-24 Right Front Passenger Position1-24 Air Bag System1-35 Center Passenger Position

1-36 Rear Seat Passengers1-40 Rear Safety Belt Comfort Guides for Children

and Small Adults1-42 Children1-46 Child Restraints1-62 Larger Children1-65 Safety Belt Extender1-65 Checking Your Restraint Systems1-65 Replacing Restraint System Parts After

a Crash

yellowblue

1-2

Seats and Seat ControlsThis section tells you about the seats -- how to adjustthem, and fold them up and down. It also tells you aboutreclining front seatbacks and head restraints.

Manual Front Seat

CAUTION:

You can lose control of the vehicle if you try toadjust a manual driver’s seat while the vehicle ismoving. The sudden movement could startle andconfuse you, or make you push a pedal when youdon’t want to. Adjust the driver’s seat only whenthe vehicle is not moving.

If your vehicle has a manual bucket or split bench seat,you can adjust it with this lever located at the front ofthe seat.

Lift the lever at the front of the seat to unlock it. Usingyour body, slide the seat to where you want it. Then,release the lever and try to move the seat with your bodyin order to make sure the seat is locked into place.

yellowblue

1-3

Cushion Tilt (If Equipped)

If your vehicle has this feature, you can raise or lowerthe front of the driver’s or passenger’s seat with thislever located at the inside edge of the seat. To raise orlower the front of the seat, move the lever up or down ina continuous motion until the cushion reaches thedesired height.

Manual Lumbar Control (If Equipped)

If your vehicle has a lumbaradjustment, you canincrease or decrease lumbarsupport in an area of thelower seatback.

To increase support, turn the knob towards the front ofthe vehicle.

To decrease support, turn the knob towards the rear ofthe vehicle.

yellowblue

1-4

Power Seat(s) (If Equipped)

Horizontal Control: If your vehicle has a power seat,you can adjust it with this control located at the outsideedge of the seat.

Raise the front of the seat cushion by raising the forwardedge of the button. Lower the front of the seat cushionby lowering the forward edge of the button. Move theseat forward by moving the whole button toward thefront of the vehicle.

Raise the rear of the seat cushion by raising the rearedge of the button. Lower the rear of the seat cushion bylowering the rear edge of the button. Move the seatrearward by moving the whole button toward the rear ofthe vehicle.

Moving the whole button up or down raises or lowersthe entire seat cushion.

Vertical Control: If your vehicle has the powerreclining seats, you can use this button to adjust theangle of the seatback. Move the reclining front seatbackrearward by moving the button toward the rear of thevehicle. Move the seatback forward by moving thebutton toward the front of the vehicle. See “RecliningSeatbacks” in the Index for further information.

yellowblue

1-5

Power Lumbar Control (If Equipped)

If you have power lumbaradjustment, you canincrease or decrease lumbarsupport in an area of thelower seatback.

To increase support, press and hold the front of thecontrol. Let go of the control when the lower seatbackreaches the desired level of support.To decrease support, press and hold the rear of thecontrol. Let go of the control when the lower seatbackreaches the desired level of support.You can also reshape the back wing area of the lower seatback.To increase support, press and hold the top of thecontrol. Let go of the control when the lower seatbackreaches the desired level of support.

To decrease support, press and hold the bottom of thecontrol. Let go of the control when the lower seatbackreaches the desired level of support.

Memory Seat (If Equipped)

The memory functioncontrols the driver’s seat cushion and recliner positions.

It does not store the lumbar or back support positions.

To set your memory seat:

1. Adjust the driver’s seat to your desired position.

2. Press the SET button and then press the 1 or 2 sideof the memory control within five seconds.

When your vehicle is in PARK (P), press the 1 or 2button of the memory control to recall the seat setting.

To do the same thing for a second driver, follow thepreceding steps, but press the other number of thememory control.

yellowblue

1-6

Heated Front Seats (If Equipped)

If your vehicle has heatedfront seats, the ignition must be in RUN for them to operate.

The control for the driver’s side heated seat is located onthe driver’s side door panel. The control for thepassenger’s side heated seat is located on thepassenger’s side door panel.

To activate the heated seats, press the button once forthe HI heat setting. Press the button again for the LOheat setting. To turn off the heated seats, press the buttona third time. An indicator light on the button willilluminate for each heat setting anytime the heated seatsare operating.

Reclining Seatbacks

To adjust the front seatback, lift the lever upward.Release the lever to lock the seatback where you want it.Lift the lever again upward and the seatback will go toan upright position.

If your vehicle has power seats with a power recliner,see “Power Seats” in the Index for further informationon how to operate the reclining seatback feature.

yellowblue

1-7

But don’t have a seatback reclined if your vehicle is moving.

CAUTION:

Sitting in a reclined position when your vehicle isin motion can be dangerous. Even if you buckleup, your safety belts can’t do their job whenyou’re reclined like this.The shoulder belt can’t do its job. In a crash, youcould go into it, receiving neck or other injuries.The lap belt can’t do its job either. In a crash thebelt could go up over your abdomen. The beltforces would be there, not at your pelvic bones.This could cause serious internal injuries.For proper protection when the vehicle is inmotion, have the seatback upright. Then sit well back in the seat and wear your safety belt properly.

yellowblue

1-8

Head RestraintsSlide the head restraint up or down so that the top of therestraint is closest to the top of your ears. This positionreduces the chance of a neck injury in a crash.

On some models, the head restraints tilt forward andrearward also.

To tilt the head restraints forward, grasp the top of therestraint and move it forward to where you want it to gountil you hear a click. It will then be locked into thatposition until you need to move it again. Pulling itforward past the last position will allow the restraint toreturn to its upright position.

Seatback Latches

CAUTION:

If the seatback isn’t locked, it could moveforward in a sudden stop or crash. That couldcause injury to the person sitting there. Alwayspress rearward on the seatback to be sure it is locked.

The seatbacks fold forward to let you access the rear ofthe cab.

To fold a front seatbackforward, pull this leverforward and fold theseatback forward.

To return the seatback to the upright position, just pushthe seatback rearward until it latches. After returning theseatback to its upright position, pull the seatbackforward to make sure it is locked.

yellowblue

1-9

Easy Entry Seat (Extended Cab Only) (If Equipped)

CAUTION:

If any easy entry seat isn’t locked, it can move. In a sudden stop or crash, the person sitting therecould be injured. And, even if there is no crash orsudden stop, a driver sitting in an unlocked easyentry seat could be startled by the suddenmovement and hit the wrong control or pedal,causing an accident. After you’ve used it, be sureto push rearward on any easy entry seat to besure it is locked.

The manual driver side front bucket seat and the manualdriver side split bench seat of your vehicle may have aneasy entry feature. This makes it easy to get in and outof the rear seat.

To operate the seat, pullforward on the top of thislever and tilt the seatbackforward toward the front ofthe vehicle.

When you do, the seat bottom will release. Just pull orpush the seat forward until it stops.

To return the seat to its regular position, return theseatback to its upright position, then push the whole seatrearward until it latches.

After returning the seat to its regular position, try tomove the seat with your body in order to make sure theseat is locked into place.

yellowblue

1-10

Rear Seat (Extended Cab)

Folding the Rear Seat

The extended cab’s rear seat can be folded up to providemore cargo space. To fold the seat:

1. Pull forward on therelease strap locatedunder the rear seat cushion.

2. Fold the seat cushion upward until it latches with the seatback.

3. Push and pull on the seatto make sure the seat is secure.

The extended cab’s rear seat can also be folded open formore seating space. To use the seat:

1. Push rearward on the seat cushion while pulling upon the release strap under the seat cushion. Pull theseat cushion downward until it latches.

2. After pulling the seat cushion down, pull up on it tomake sure it is locked.

yellowblue

1-11

Safety Belts: They’re for EveryoneThis part of the manual tells you how to use safety beltsproperly. It also tells you some things you should not dowith safety belts.

And it explains the air bag system.

CAUTION:

Don’t let anyone ride where he or she can’t weara safety belt properly. If you are in a crash andyou’re not wearing a safety belt, your injuriescan be much worse. You can hit things inside thevehicle or be ejected from it. You can be seriouslyinjured or killed. In the same crash, you mightnot be if you are buckled up. Always fasten yoursafety belt, and check that your passengers’ beltsare fastened properly too.

CAUTION:

It is extremely dangerous to ride in a cargo area,inside or outside of a vehicle. In a collision,people riding in these areas are more likely to beseriously injured or killed. Do not allow people toride in any area of your vehicle that is notequipped with seats and safety belts. Be sureeveryone in your vehicle is in a seat and using asafety belt properly.

Your vehicle has a light thatcomes on as a reminder tobuckle up. (See “Safety Belt Reminder Light” in the Index.)

yellowblue

1-12

In most states and Canadian provinces, the law says towear safety belts. Here’s why: They work.

You never know if you’ll be in a crash. If you do have acrash, you don’t know if it will be a bad one.

A few crashes are mild, and some crashes can be soserious that even buckled up a person wouldn’t survive.But most crashes are in between. In many of them,people who buckle up can survive and sometimes walkaway. Without belts they could have been badly hurt or killed.

After more than 30 years of safety belts in vehicles, the facts are clear. In most crashes buckling up doesmatter ... a lot!

Why Safety Belts WorkWhen you ride in or on anything, you go as fast as it goes.

Take the simplest vehicle. Suppose it’s just a seat on wheels.

yellowblue

1-13

Put someone on it. Get it up to speed. Then stop the vehicle. The riderdoesn’t stop.

yellowblue

1-14

The person keeps going until stopped by something.

In a real vehicle, it could be the windshield ...

or the instrument panel ...

yellowblue

1-15

or the safety belts!

With safety belts, you slow down as the vehicle does.You get more time to stop. You stop over more distance,and your strongest bones take the forces. That’s whysafety belts make such good sense.

Here Are Questions Many People AskAbout Safety Belts -- and the AnswersQ: Won’t I be trapped in the vehicle after an

accident if I’m wearing a safety belt?

A: You could be -- whether you’re wearing a safetybelt or not. But you can unbuckle a safety belt,even if you’re upside down. And your chance ofbeing conscious during and after an accident, soyou can unbuckle and get out, is much greater ifyou are belted.

Q: If my vehicle has air bags, why should I have towear safety belts?

A: Air bags are in many vehicles today and will be in most of them in the future. But they aresupplemental systems only; so they work withsafety belts -- not instead of them. Every air bagsystem ever offered for sale has required the use ofsafety belts. Even if you’re in a vehicle that has airbags, you still have to buckle up to get the mostprotection. That’s true not only in frontal collisions,but especially in side and other collisions.

yellowblue

1-16

Q: If I’m a good driver, and I never drive far fromhome, why should I wear safety belts?

A: You may be an excellent driver, but if you’re in anaccident -- even one that isn’t your fault -- you andyour passengers can be hurt. Being a good driverdoesn’t protect you from things beyond yourcontrol, such as bad drivers.

Most accidents occur within 25 miles (40 km) of home. And the greatest number of seriousinjuries and deaths occur at speeds of less than 40 mph (65 km/h).

Safety belts are for everyone.

How to Wear Safety Belts ProperlyAdultsThis part is only for people of adult size.

Be aware that there are special things to know aboutsafety belts and children. And there are different rulesfor smaller children and babies. If a child will be riding in your vehicle, see the part of this manual called “Children.” Follow those rules for everyone’s protection.

First, you’ll want to know which restraint systems yourvehicle has.

We’ll start with the driver position.

Driver PositionThis part describes the driver’s restraint system.

yellowblue

1-17

Lap-Shoulder BeltThe driver has a lap-shoulder belt. Here’s how to wear it properly.

1. Close and lock the door.

2. Adjust the seat (to see how, see “Seats” in the Index)so you can sit up straight.

3. Pick up the latch plate and pull the belt across you.Don’t let it get twisted.

The shoulder belt may lock if you pull the belt acrossyou very quickly. If this happens, let the belt go backslightly to unlock it. Then pull the belt across youmore slowly.

4. Push the latch plate into the buckle until it clicks.

Pull up on the latch plate to make sure it is secure.If the belt isn’t long enough, see “Safety BeltExtender” at the end of this section.

Make sure the release button on the buckle ispositioned so you would be able to unbuckle thesafety belt quickly if you ever had to.

yellowblue

1-18

5. To make the lap part tight, pull down on the buckleend of the belt as you pull up on the shoulder belt.

The lap part of the belt should be worn low and snug onthe hips, just touching the thighs. In a crash, this appliesforce to the strong pelvic bones. And you’d be less likelyto slide under the lap belt. If you slid under it, the beltwould apply force at your abdomen. This could causeserious or even fatal injuries. The shoulder belt should goover the shoulder and across the chest. These parts of thebody are best able to take belt restraining forces.

The safety belt locks if there’s a sudden stop or crash, orif you pull the belt very quickly out of the retractor.

yellowblue

1-19

Q: What’s wrong with this?

A: The shoulder belt is too loose. It won’t give nearlyas much protection this way.

CAUTION:

You can be seriously hurt if your shoulder belt istoo loose. In a crash, you would move forwardtoo much, which could increase injury. Theshoulder belt should fit against your body.

yellowblue

1-20

Q: What’s wrong with this?

A: The belt is buckled in the wrong place.

CAUTION:

You can be seriously injured if your belt isbuckled in the wrong place like this. In a crash,the belt would go up over your abdomen. The belt forces would be there, not at the pelvicbones. This could cause serious internal injuries.Always buckle your belt into the buckle nearest you.

yellowblue

1-21

Q: What’s wrong with this?

A: The shoulder belt is worn under the arm. It shouldbe worn over the shoulder at all times.

CAUTION:

You can be seriously injured if you wear theshoulder belt under your arm. In a crash, yourbody would move too far forward, which wouldincrease the chance of head and neck injury.Also, the belt would apply too much force to theribs, which aren’t as strong as shoulder bones.You could also severely injure internal organslike your liver or spleen.

yellowblue

1-22

Q: What’s wrong with this?

A: The belt is twisted across the body.

CAUTION:

You can be seriously injured by a twisted belt. Ina crash, you wouldn’t have the full width of thebelt to spread impact forces. If a belt is twisted,make it straight so it can work properly, or askyour dealer to fix it.

yellowblue

1-23

To unlatch the belt, just push the button on the buckle.The belt should go back out of the way.

Before you close the door, be sure the belt is out of theway. If you slam the door on it, you can damage both thebelt and your vehicle.

Safety Belt Use During PregnancySafety belts work for everyone, including pregnantwomen. Like all occupants, they are more likely to beseriously injured if they don’t wear safety belts.

A pregnant woman should wear a lap-shoulder belt, andthe lap portion should be worn as low as possible, belowthe rounding, throughout the pregnancy.

yellowblue

1-24

The best way to protect the fetus is to protect themother. When a safety belt is worn properly, it’s morelikely that the fetus won’t be hurt in a crash. Forpregnant women, as for anyone, the key to makingsafety belts effective is wearing them properly.

Right Front Passenger PositionTo learn how to wear the right front passenger’s safetybelt properly, see “Driver Position” earlier in this section.

The right front passenger’s safety belt works the sameway as the driver’s safety belt -- except for one thing. If you ever pull the shoulder portion of the belt out allthe way, you will engage the child restraint lockingfeature. If this happens, just let the belt go back all theway and start again.

Air Bag SystemThis part explains the air bag system.

Your vehicle has air bags -- one air bag for the driverand another air bag for the right front passenger.

Frontal air bags are designed to help reduce the risk ofinjury from the force of an inflating air bag. But theseair bags must inflate very quickly to do their job andcomply with federal regulations.

Here are the most important things to know about the airbag system:

CAUTION:

You can be severely injured or killed in a crash ifyou aren’t wearing your safety belt -- even if youhave air bags. Wearing your safety belt during acrash helps reduce your chance of hitting thingsinside the vehicle or being ejected from it. Airbags are “supplemental restraints” to the safetybelts. All air bags are designed to work withsafety belts, but don’t replace them. Air bags aredesigned to work only in moderate to severecrashes where the front of your vehicle hitssomething. They aren’t designed to inflate at allin rollover, rear, side or low-speed frontalcrashes. And, for unrestrained occupants, airbags may provide less protection in frontalcrashes than more forceful air bags haveprovided in the past. Everyone in your vehicleshould wear a safety belt properly -- whether ornot there’s an air bag for that person.

yellowblue

1-25

CAUTION:

Air bags inflate with great force, faster than theblink of an eye. If you’re too close to an inflatingair bag, as you would be if you were leaningforward, it could seriously injure you. Safetybelts help keep you in position before and duringa crash. Always wear your safety belt, even withair bags. The driver should sit as far back aspossible while still maintaining control of the vehicle.

CAUTION:

Anyone who is up against, or very close to, anyair bag when it inflates can be seriously injuredor killed. Air bags plus lap-shoulder belts offerthe best protection for adults, but not for youngchildren and infants. Neither the vehicle’s safetybelt system nor its air bag system is designed forthem. Young children and infants need theprotection that a child restraint system canprovide. Always secure children properly in yourvehicle. To read how, see the part of this manualcalled “Children.”

yellowblue

1-26

There is an air bag readinesslight on the instrumentpanel, which shows the air bag symbol.

The system checks the air bag electrical system formalfunctions. The light tells you if there is an electricalproblem. See “Air Bag Readiness Light” in the Indexfor more information.

How the Air Bag System Works

Where are the air bags?

The driver’s air bag is in the middle of the steering wheel.

yellowblue

1-27

The right front passenger’s air bag is in the instrumentpanel on the passenger’s side.

CAUTION:

If something is between an occupant and an air bag, the bag might not inflate properly or itmight force the object into that person. The pathof an inflating air bag must be kept clear. Don’tput anything between an occupant and an airbag, and don’t attach or put anything on thesteering wheel hub or on or near any other air bag covering.

yellowblue

1-28

When should an air bag inflate?

An air bag is designed to inflate in a moderate to severefrontal or near-frontal crash. The air bag will inflateonly if the impact speed is above the system’s designed“threshold level.” If your vehicle goes straight into awall that doesn’t move or deform, the threshold level isabout 9 to 16 mph (14 to 26 km/h). The threshold levelcan vary, however, with specific vehicle design, so thatit can be somewhat above or below this range. If yourvehicle strikes something that will move or deform, suchas a parked car, the threshold level will be higher. Theair bag is not designed to inflate in rollovers, sideimpacts or rear impacts, because inflation would nothelp the occupant.

In any particular crash, no one can say whether an airbag should have inflated simply because of the damageto a vehicle or because of what the repair costs were.Inflation is determined by the angle of the impact andhow quickly the vehicle slows down in frontal ornear-frontal impacts.

The air bag system is designed to work properly under awide range of conditions, including off-road usage.Observe safe driving speeds, especially on rough terrain.As always, wear your safety belt. See “Off-RoadDriving” in the Index for more tips on off-road driving.

What makes an air bag inflate?

In an impact of sufficient severity, the air bag sensingsystem detects that the vehicle is in a crash. The sensingsystem triggers a release of gas from the inflator, whichinflates the air bag. The inflator, air bag and relatedhardware are all part of the air bag modules inside thesteering wheel and in the instrument panel in front of theright front passenger.

How does an air bag restrain?

In moderate to severe frontal or near-frontal collisions,even belted occupants can contact the steering wheel orthe instrument panel. Air bags supplement the protectionprovided by safety belts. Air bags distribute the force ofthe impact more evenly over the occupant’s upper body,stopping the occupant more gradually. But air bagswould not help you in many types of collisions,including rollovers, rear impacts and side impacts,primarily because an occupant’s motion is not towardthose air bags. Air bags should never be regarded asanything more than a supplement to safety belts, and then only in moderate to severe frontal ornear-frontal collisions.

yellowblue

1-29

What will you see after an air bag inflates?

After an air bag inflates, it quickly deflates, so quicklythat some people may not even realize the air baginflated. Some components of the air bag module -- thesteering wheel hub for the driver’s air bag, or theinstrument panel for the right front passenger’s bag -- will be hot for a short time. The parts of the bag that come into contact with you may be warm, butnot too hot to touch. There will be some smoke and dustcoming from vents in the deflated air bags. Air baginflation doesn’t prevent the driver from seeing or frombeing able to steer the vehicle, nor does it stop peoplefrom leaving the vehicle.

CAUTION:

When an air bag inflates, there is dust in the air.This dust could cause breathing problems forpeople with a history of asthma or otherbreathing trouble. To avoid this, everyone in thevehicle should get out as soon as it is safe to do so.If you have breathing problems but can’t get outof the vehicle after an air bag inflates, then getfresh air by opening a window or door.

In many crashes severe enough to inflate an air bag,windshields are broken by vehicle deformation.Additional windshield breakage may also occur from theright front passenger air bag.

� Air bags are designed to inflate only once. After theyinflate, you’ll need some new parts for your air bagsystem. If you don’t get them, the air bag systemwon’t be there to help protect you in another crash.A new system will include air bag modules andpossibly other parts. The service manual for yourvehicle covers the need to replace other parts.

� Your vehicle is equipped with a crash sensing anddiagnostic module, which records information aboutthe air bag system. The module records informationabout the readiness of the system, when the systemcommands air bag inflation and driver’s safety beltusage at deployment. Some modules also recordspeed, engine rpm, brake and throttle data.

� Let only qualified technicians work on your air bagsystem. Improper service can mean that your air bagsystem won’t work properly. See your dealer for service.

yellowblue

1-30

NOTICE:

If you damage the covering for the driver’s or theright front passenger’s air bag, the bag may notwork properly. You may have to replace the airbag module in the steering wheel or both the airbag module and the instrument panel for theright front passenger’s air bag. Do not open orbreak the air bag coverings.

AIR BAG OFF SwitchYour vehicle has a switch on the instrument panel thatyou can use to turn off the right front passenger’s air bag.

yellowblue

1-31

This switch should only be turned to AIR BAG OFF ifthe person in the right front passenger’s position is amember of a passenger risk group identified by thenational government as follows:

Infant. An infant (less than 1 year old) must ride in thefront seat because:

� my vehicle has no rear seat;

� my vehicle has a rear seat too small to accommodatea rear-facing infant seat; or

� the infant has a medical condition which, accordingto the infant’s physician, makes it necessary for theinfant to ride in the front seat so that the driver canconstantly monitor the child’s condition.

Child age 1 to 12. A child age 1 to 12 must ride in thefront seat because:

� my vehicle has no rear seat;

� although children ages 1 to 12 ride in the rearseat(s) whenever possible, children ages 1 to 12sometimes must ride in the front because no space isavailable in the rear seat(s) of my vehicle; or

� the child has a medical condition which, accordingto the child’s physician, makes it necessary for thechild to ride in the front seat so that the driver canconstantly monitor the child’s condition.

Medical Condition. A passenger has a medicalcondition which, according to his or her physician:

� causes the passenger air bag to pose a special riskfor the passenger; and

� makes the potential harm from the passenger air bagin a crash greater than the potential harm fromturning off the air bag and allowing the passenger,even if belted, to hit the dashboard or windshield in a crash.

CAUTION:

If the right front passenger’s air bag is turned offfor a person who isn’t in a risk group identifiedby the national government, that person won’thave the extra protection of an air bag. In acrash, the air bag wouldn’t be able to inflate andhelp protect the person sitting there. Don’t turnoff the passenger’s air bag unless the personsitting there is in a risk group.

yellowblue

1-32

To turn off the right front passenger’s air bag, insertyour ignition key into the switch, push in, and move theswitch to AIR BAG OFF.

The AIR BAG OFF light will come on to let you knowthat the right front passenger’s air bag is off. The rightfront passenger’s air bag will remain off until you turn itback on again, and the AIR BAG OFF light will stay onto remind you that the air bag is off.

CAUTION:

If the air bag readiness light ever comes on whenyou have turned off the air bag, it means thatsomething may be wrong with the air bag system.The right front passenger’s air bag could inflateeven though the switch is off.

If your vehicle is a regular cab pickup and thisever happens, don’t let anyone whom thenational government has identified as a memberof a passenger air bag risk group sit in the rightfront passenger’s position (for example, don’tsecure a rear-facing child restraint in yourvehicle) until you have your vehicle serviced.

If your vehicle is an extended cab pickup and thisever happens, don’t let anyone whom thenational government has identified as a memberof a passenger air bag risk group sit in the rightfront passenger’s position (for example, don’tsecure a rear-facing child restraint in the rightfront passenger’s seat) until you have yourvehicle serviced.

yellowblue

1-33

To turn the right front passenger’s air bag on again,insert your ignition key into the switch, push in, andmove the switch to the ON position.

Servicing Your Air Bag-Equipped VehicleAir bags affect how your vehicle should be serviced.There are parts of the air bag system in several placesaround your vehicle. You don’t want the system toinflate while someone is working on your vehicle. Yourdealer and the service manual have information aboutservicing your vehicle and the air bag system. Topurchase a service manual, see “Service and OwnerPublications” in the Index.

CAUTION:

For up to two minutes after the ignition key isturned off and the battery is disconnected, an airbag can still inflate during improper service. Youcan be injured if you are close to an air bag whenit inflates. Avoid wires wrapped with yellow tapeor yellow connectors. They are probably part ofthe air bag system. Be sure to follow properservice procedures, and make sure the personperforming work for you is qualified to do so.

The air bag system does not need regular maintenance.

yellowblue

1-34

Adding Equipment to Your AirBag-Equipped Vehicle

Q: If I add a push bumper or a bicycle rack to thefront of my vehicle, will it keep the air bagsfrom working properly?

A: As long as the push bumper or bicycle rack isattached to your vehicle so that the vehicle’s basicstructure isn’t changed, it’s not likely to keep theair bags from working properly in a crash.

Q: Is there anything I might add to the front of thevehicle that could keep the air bags fromworking properly?

A: Yes. If you add things that change your vehicle’sframe, bumper system, front end sheet metal orheight, they may keep the air bag system fromworking properly. Also, the air bag system may notwork properly if you relocate any of the air bagsensors. If you have any questions about this, youshould contact Customer Assistance before youmodify your vehicle. (The phone numbers andaddresses for Customer Assistance are in Step Two ofthe Customer Satisfaction Procedure in this manual.See “Customer Satisfaction Procedure” in the Index.)

Q: What if I add a snow plow? Will it keep the air bags from working properly?

A: We’ve designed our air bag systems to workproperly under a wide range of conditions,including snow plowing with vehicles equippedwith the optional Snow Plow Prep Package (RPOVYU). But don’t change or defeat the snow plow’s“tripping mechanism.” If you do, it can damageyour snow plow and your vehicle, and it may causean air bag inflation.

yellowblue

1-35

Center Passenger Position

Lap BeltIf your vehicle has front and rear bench seats, someonecan sit in the center positions.

When you sit in a center seating position, you have a lapsafety belt, which has no retractor. To make the beltlonger, tilt the latch plate and pull it along the belt.

yellowblue

1-36

To make the belt shorter, pull its free end as shown untilthe belt is snug.

Buckle, position and release it the same way as the lappart of a lap-shoulder belt. If the belt isn’t long enough,see “Safety Belt Extender” at the end of this section.

Make sure the release button on the buckle is positionedso you would be able to unbuckle the safety belt quicklyif you ever had to.

Rear Seat PassengersIt’s very important for rear seat passengers to buckle up!Accident statistics show that unbelted people in the rearseat are hurt more often in crashes than those who arewearing safety belts.

Rear passengers who aren’t safety belted can be thrownout of the vehicle in a crash. And they can strike othersin the vehicle who are wearing safety belts.

Rear Seat Outside Passenger Positions(Extended Cab)

yellowblue

1-37

Lap-Shoulder Belt (Extended Cab)

The positions next to the windows have lap-shoulderbelts. Here’s how to wear one properly.

1. Pick up the latch plate and pull the belt across you.Don’t let it get twisted. The shoulder belt may lock ifyou pull the belt across you very quickly. If thishappens, let the belt go back slightly to unlock it.Then pull the belt across you more slowly.

2. Push the latch plate into the buckle until it clicks.

Pull up on the latch plate to make sure it is secure.

When the shoulder belt is pulled out all the way, itwill lock. If it does, let it go back all the way andstart again.

If the belt is not long enough, see “Safety BeltExtender” at the end of this section.

Make sure the release button on the buckle ispositioned so you would be able to unbuckle thesafety belt quickly if you ever had to.

yellowblue

1-38

3. To make the lap part tight, pull down on the buckleend of the belt as you pull up on the shoulder part.

The lap part of the belt should be worn low and snug onthe hips, just touching the thighs. In a crash, this appliesforce to the strong pelvic bones. And you’d be less likelyto slide under the lap belt. If you slid under it, the beltwould apply force at your abdomen. This could causeserious or even fatal injuries. The shoulder belt should goover the shoulder and across the chest. These parts of thebody are best able to take belt restraining forces.

The safety belt locks if there’s a sudden stop or a crash.

The safety belt also locks if you pull the belt veryquickly out of the retractor.

yellowblue

1-39

CAUTION:

You can be seriously hurt if your shoulder belt istoo loose. In a crash, you would move forwardtoo much, which could increase injury. Theshoulder belt should fit against your body.

To unlatch the belt, just push the button on the buckle.

yellowblue

1-40

Rear Safety Belt Comfort Guides forChildren and Small AdultsIf your vehicle has a rear seat, your vehicle has shoulderbelt comfort guides. This feature will provide addedsafety belt comfort for children who have outgrownchild restraints and for small adults. When installed on ashoulder belt, the comfort guide pulls the belt awayfrom the neck and head.

There is one guide for each outside passenger position inthe rear seat. To provide added safety belt comfort forchildren who have outgrown child restraints and forsmaller adults, the comfort guides may be installed onthe shoulder belts. Here’s how to install a comfort guideand use the safety belt:

1. Remove the guide from its storage clip on theinterior body.

yellowblue

1-41

2. Place the guide over the belt and insert the two edgesof the belt into the slots of the guide.

3. Be sure that the belt is not twisted and it lies flat. The guide must be on top of the belt.

yellowblue

1-42

4. Buckle, position and release the safety belt asdescribed in “Rear Seat Passenger Positions(Extended Cab)” earlier in this section. Make surethat the shoulder belt crosses the shoulder.

To remove and store the comfort guides, squeeze thebelt edges together so that you can take them out fromthe guides. Slide the guide onto the storage clip.

ChildrenEveryone in a vehicle needs protection! That includesinfants and all children smaller than adult size. Neitherthe distance traveled nor the age and size of the travelerchanges the need, for everyone, to use safety restraints.In fact, the law in every state in the United States and inevery Canadian province says children up to some agemust be restrained while in a vehicle.

Smaller Children and Babies

CAUTION:

Children who are up against, or very close to, anyair bag when it inflates can be seriously injuredor killed. Air bags plus lap-shoulder belts offerthe best protection for adults, but not for youngchildren and infants. Neither the vehicle’s safetybelt system nor its air bag system is designed forthem. Young children and infants need theprotection that a child restraint system canprovide. Always secure children properly in your vehicle.

yellowblue

1-43

CAUTION:

Smaller children and babies should always berestrained in a child or infant restraint. Theinstructions for the restraint will say whether it isthe right type and size for your child. A veryyoung child’s hip bones are so small that aregular belt might not stay low on the hips, as itshould. Instead, the belt will likely be over thechild’s abdomen. In a crash, the belt would applyforce right on the child’s abdomen, which couldcause serious or fatal injuries. So, be sure thatany child small enough for one is always properlyrestrained in a child or infant restraint.

Infants need complete support, including support for thehead and neck. This is necessary because an infant’sneck is weak and its head weighs so much comparedwith the rest of its body. In a frontal crash, an infant in arear-facing restraint settles into the restraint, so the crashforces can be distributed across the strongest part of theinfant’s body, the back and shoulders. A baby should besecured in an appropriate infant restraint. This is soimportant that many hospitals today won’t release anewborn infant to its parents unless there is an infantrestraint available for the baby’s first trip in a motor vehicle.

yellowblue

1-44

CAUTION:

Never hold a baby in your arms while riding in avehicle. A baby doesn’t weigh much -- until acrash. During a crash a baby will become soheavy you can’t hold it. For example, in a crashat only 25 mph (40 km/h), a 12-lb. (5.5 kg) babywill suddenly become a 240-lb. (110 kg) force onyour arms. The baby would be almost impossibleto hold.

CAUTION: (Continued)

yellowblue

1-45

CAUTION: (Continued)

Secure the baby in an infant restraint. If you’reusing the infant restraint in the right frontpassenger’s position, be sure to turn off the airbag. See “Air Bag Off Switch” and “Securing aChild Restraint in the Right Front Seat Position”in the Index for more on this, includingimportant safety information.

yellowblue

1-46

Child RestraintsEvery time infants and young children ride in vehicles,they should have protection provided by appropriate restraints.

Q: What are the different types of add-on child restraints?

A: Add-on child restraints are available in four basictypes. When selecting a child restraint, take intoconsideration not only the child’s weight and size,but also whether or not the restraint will becompatible with the motor vehicle in which it willbe used.

An infant car bed (A) is a special bed made for usein a motor vehicle. It’s an infant restraint systemdesigned to restrain or position a child on acontinuous flat surface. With an infant car bed,make sure that the infant’s head rests toward thecenter of the vehicle.

yellowblue

1-47

A rear-facing infant restraint (B) positions an infantto face the rear of the vehicle. Rear-facing infantrestraints are designed for infants of up to about 20 lbs. (9 kg) and about one year of age. This typeof restraint faces the rear so that the infant’s head,neck and body can have the support they need in a frontal crash. Some infant seats come in two parts -- the base stays secured in the vehicleand the seat part is removable.

yellowblue

1-48

A forward-facing child restraint (C-E) positions a child upright to face forward in the vehicle. These forward-facing restraints are designed tohelp protect children who are from 20 to 40 lbs. (9 to 18 kg) and about 26 to 40 inches (66 to 102 cm) in height, or up to around four yearsof age. One type, a convertible restraint, isdesigned to be used either as a rear-facing infantseat or a forward-facing child seat.

yellowblue

1-49

A booster seat (F) is designed for children who are about 40 to 60 lbs., or even up to 80 lbs. (18 to 27 kg, or even up to 36 kg), and about fourto eight years of age. A booster seat is designed toimprove the fit of the vehicle’s safety belt system.Booster seats with shields use lap-only belts;however, booster seats without shields uselap-shoulder belts. Booster seats can also help achild to see out the window.

When choosing a child restraint, be sure the childrestraint is designed to be used in a vehicle. If it is, itwill have a label saying that it meets federal motorvehicle safety standards.

Then follow the instructions for the restraint. You mayfind these instructions on the restraint itself or in abooklet, or both. These restraints use the belt system inyour vehicle, but the child also has to be secured withinthe restraint to help reduce the chance of personal injury.The instructions that come with the infant or childrestraint will show you how to do that. Both the owner’smanual and the child restraint instructions are important,so if either one of these is not available, obtain areplacement copy from the manufacturer.

yellowblue

1-50

Where to Put the Restraint (Regular Cab Pickup)The child restraint must be secured properly in the rightfront passenger seat. If you want to secure a rear-facingchild restraint in the right front passenger’s seat, turn offthe passenger’s air bag. See “AIR BAG OFF Switch”and “Securing a Child Restraint in the Right Front SeatPosition” in the Index for more on this, includingimportant safety information.

CAUTION:

A child in a rear-facing child restraint can beseriously injured or killed if the right frontpassenger’s air bag inflates. This is because theback of the rear-facing child restraint would bevery close to the inflating air bag. Be sure to turnoff the air bag before using a rear-facing childrestraint in the right front seat position.

Keep in mind that an unsecured child restraint can movearound in a collision or sudden stop and injure people inthe vehicle -- even when no child is in it.

Where to Put the Restraint (Extended Cab Pickup)Accident statistics show that children are safer if theyare restrained in the rear rather than the front seat. We atGeneral Motors therefore recommend that you put yourchild restraint in the rear seat. There is limited space inthe rear seating area of an extended cab model. If youwant to secure a child restraint in a rear seating positionof an extended cab model, especially in the rear centerposition, be sure to study the instructions that came withyour child restraint to see if there is enough room tosecure your seat properly.

If you want to secure a rear-facing child restraint in theright front passenger’s seat, turn off the passenger’s airbag. See “AIR BAG OFF Switch” and “Securing aChild Restraint in the Right Front Seat Position” in the Index for more on this, including important safety information.

yellowblue

1-51

CAUTION:

A child in a rear-facing child restraint can beseriously injured or killed if the right frontpassenger’s air bag inflates. This is because theback of the rear-facing child restraint would bevery close to the inflating air bag. Be sure to turnoff the air bag before using a rear-facing childrestraint in the right front seat position.

Wherever you install it, be sure to secure the childrestraint properly.

Keep in mind that an unsecured child restraint can movearound in a collision or sudden stop and injure people inthe vehicle. Be sure to properly secure any childrestraint in your vehicle -- even when no child is in it.

Top Strap

In Canada, the law requires that forward-facing childrestraints have a top strap, and that the strap beanchored. In the United States, some child restraints alsohave a top strap. If your child restraint has a top strap, itshould be anchored.

If your vehicle is a regular cab pickup, an anchorbracket is located behind the right front passenger’s seat.

yellowblue

1-52

In order to get to the bracket, you’ll have to remove thetrim plug covering it.

If you need to have an anchor bracket installed for a rearseat position in an extended cab, your dealer can get aspecial kit with anchor hardware and installationinstructions and then install the anchor for you. Thiswork will be done for you free of charge. Or, you mayinstall the anchor yourself using the instructionsprovided in the kit.

Anchor the top strap to this bracket. Once you have thetop strap anchored, you’ll be ready to secure the childrestraint itself.

yellowblue

1-53

Securing a Child Restraint in a RearOutside Seat Position (Extended Cab)There is limited space in the rear seating area of anextended cab model. If you want to secure a childrestraint in a rear outside seating position, be sure tostudy the instructions that came with your child restraint to see if there is enough room to secure yourseat properly.

You’ll be using the lap-shoulder belt. See the earlier partabout the top strap if the child restraint has one. Be sureto follow the instructions that came with the childrestraint. Secure the child in the child restraint when andas the instructions say.

1. Put the restraint on the seat.

2. Pick up the latch plate, and run the lap and shoulderportions of the vehicle’s safety belt through oraround the restraint. The child restraint instructionswill show you how. If the shoulder belt goes in front of the child’s face or neck, put it behind thechild restraint.

3. Buckle the belt. Make sure the release button ispositioned so you would be able to unbuckle thesafety belt quickly if you ever had to.

yellowblue

1-54

4. Pull the rest of the shoulder belt all the way out ofthe retractor to set the lock.

5. To tighten the belt, feed the shoulder belt back intothe retractor while you push down on the childrestraint. If you’re using a forward-facing childrestraint, you may find it helpful to use your knee to push down on the child restraint as you tighten the belt.

6. Push and pull the child restraint in differentdirections to be sure it is secure.

yellowblue

1-55

To remove the child restraint, just unbuckle the vehicle’ssafety belt and let it go back all the way. The safety beltwill move freely again and be ready to work for an adultor larger child passenger.

Securing a Child Restraint in the CenterFront Seat Position

Don’t use child restraints in this position. The restraintswon’t work properly.

Securing a Child Restraint in the CenterRear Seat Position (Extended Cab Pickup)

If you have an extended cab pickup, you can secure achild restraint in the center rear seat position.

There is limited space in the rear seating area of anextended cab model. If you want to secure a child restraintin a rear seating position of an extended cab model,especially in the rear center position, be sure to study theinstructions that came with your child restraint to see ifthere is enough room to secure your seat properly.

You’ll be using the lap belt. Be sure to follow theinstructions that came with the child restraint. Secure thechild in the child restraint when and as the instructionssay. See the earlier part about the top strap if the childrestraint has one.

yellowblue

1-56

1. Make the belt as long as possible by tilting the latchplate and pulling it along the belt.

2. Put the restraint on the seat.

3. Run the vehicle’s safety belt through or around therestraint. The child restraint instructions will showyou how.

4. Buckle the belt. Make sure the release button ispositioned so you would be able to unbuckle thesafety belt quickly if you ever had to.

yellowblue

1-57

5. To tighten the belt, pull its free end while you pushdown on the child restraint. If you’re using aforward-facing child restraint, you may find ithelpful to use your knee to push down on the childrestraint as you tighten the belt.

6. Push and pull the child restraint in differentdirections to be sure it is secure.

To remove the child restraint, just unbuckle the vehicle’ssafety belt. It will be ready to work for an adult or largerchild passenger.

Securing a Child Restraint in the RightFront Seat Position

Your vehicle has a right front passenger air bag. There’sa switch on the instrument panel that you can use to turnoff the right front passenger’s air bag when you want tosecure a rear-facing child restraint at the right frontpassenger’s position. See “AIR BAG OFF Switch” in the Index for more on this, including important safety information.

yellowblue

1-58

CAUTION:

A child in a rear-facing child restraint can beseriously injured or killed if the right frontpassenger’s air bag inflates. This is because theback of the rear-facing child restraint would bevery close to the inflating air bag. Be sure to turnoff the air bag before using a rear-facing childrestraint in the right front seat position. If aforward -facing child restraint is suitable for yourchild, always move the passenger seat as far backas it will go.

Although a rear seat is a safer place, you can secure aforward-facing child restraint in the right front seat.

yellowblue

1-59

CAUTION:

If the air bag readiness light ever comes on whenyou have turned off the air bag, it means thatsomething may be wrong with the air bag system.The right front passenger’s air bag could inflateeven though the switch is off.

If your vehicle is a regular cab pickup and thisever happens, don’t let anyone whom thenational government has identified as a memberof a passenger air bag risk group sit in the rightfront passenger’s position (for example, don’tsecure a rear-facing child restraint in yourvehicle) until you have your vehicle serviced. See“AIR BAG OFF Switch” in the Index.If your vehicle is an extended cab pickup and this ever happens, don’t let anyone whom the national government has identified as a member of a passenger air bag risk group sit in the right front passenger’s position (for example, don’t secure a rear-facing child restraint in the right front passenger’s seat) until you have your vehicle serviced. See “AIR BAG OFF Switch” in the Index.

You’ll be using the lap-shoulder belt. See the earlier partabout the top strap if the child restraint has one. Be sureto follow the instructions that came with the childrestraint. Secure the child in the child restraint when andas the instructions say.

1. Your vehicle has a right front passenger’s air bag. If you are using a rear-facing child restraint in thisseat, make sure the air bag is turned off. (See “AIRBAG OFF Switch” in the Index.) If your childrestraint is forward-facing, always move the seat asfar back as it will go before securing it in this seat.(See “Seats” in the Index.)

2. Put the restraint on the seat.

3. Pick up the latch plate, and run the lap and shoulderportions of the vehicle’s safety belt through oraround the restraint. The child restraint instructionswill show you how.

If the shoulder belt goes in front of the child’s face orneck, put it behind the child restraint.

yellowblue

1-60

4. Buckle the belt. Make sure the release button ispositioned so you would be able to unbuckle thesafety belt quickly if you ever had to.

5. Pull the rest of the shoulder belt all the way out ofthe retractor to set the lock.

yellowblue

1-61

6. To tighten the belt, feed the shoulder belt back intothe retractor while you push down on the childrestraint. If you’re using a forward-facing childrestraint, you may find it helpful to use your knee to push down on the child restraint as you tighten the belt.

7. Push and pull the child restraint in differentdirections to be sure it is secure.

To remove the child restraint, just unbuckle the vehicle’ssafety belt and let it go back all the way. The safety beltwill move freely again and be ready to work for an adultor larger child passenger.

If you were using a rear-facing child restraint, turn onthe right front passenger’s air bag when you remove therear-facing child restraint from the vehicle unless theperson who will be sitting there is a member of apassenger air bag risk group. See “AIR BAG OFFSwitch” in the Index.

CAUTION:

If the right front passenger’s air bag is turned offfor a person who isn’t in a risk group identifiedby the national government, that person won’thave the extra protection of an air bag. In acrash, the air bag wouldn’t be able to inflate andhelp protect the person sitting there. Don’t turnoff the passenger’s air bag unless the personsitting there is in a risk group. See “AIR BAGOFF Switch” in the Index for more on this,including important safety information.

yellowblue

1-62

Larger Children Children who have outgrown child restraints shouldwear the vehicle’s safety belts.

If you have the choice, a child should sit next to awindow so the child can wear a lap-shoulder belt andget the additional restraint a shoulder belt can provide.

Accident statistics show that children are safer if theyare restrained in the rear seat. But they need to use thesafety belts properly.

� Children who aren’t buckled up can be thrown out ina crash.

� Children who aren’t buckled up can strike otherpeople who are.

yellowblue

1-63

CAUTION:

Never do this.Here two children are wearing the same belt. Thebelt can’t properly spread the impact forces. In acrash, the two children can be crushed togetherand seriously injured. A belt must be used byonly one person at a time.

Q: What if a child is wearing a lap-shoulder belt,but the child is so small that the shoulder belt isvery close to the child’s face or neck?

A: Move the child toward the center of the vehicle, butbe sure that the shoulder belt still is on the child’sshoulder, so that in a crash the child’s upper bodywould have the restraint that belts provide. If thechild is sitting in a rear seat outside position, see“Rear Safety Belt Comfort Guides” in the Index. If the child is so small that the shoulder belt is stillvery close to the child’s face or neck, you mightwant to place the child in a seat that has a lap belt,if your vehicle has one.

yellowblue

1-64

CAUTION:

Never do this.Here a child is sitting in a seat that has alap-shoulder belt, but the shoulder part is behindthe child. If the child wears the belt in this way, ina crash the child might slide under the belt. Thebelt’s force would then be applied right on thechild’s abdomen. That could cause serious orfatal injuries.

Wherever the child sits, the lap portion of the beltshould be worn low and snug on the hips, just touchingthe child’s thighs. This applies belt force to the child’spelvic bones in a crash.

yellowblue

1-65

Safety Belt ExtenderIf the vehicle’s safety belt will fasten around you, youshould use it.

But if a safety belt isn’t long enough to fasten, yourdealer will order you an extender. It’s free. When you goin to order it, take the heaviest coat you will wear, so theextender will be long enough for you. The extender willbe just for you, and just for the seat in your vehicle thatyou choose. Don’t let someone else use it, and use itonly for the seat it is made to fit. To wear it, just attach itto the regular safety belt.

Checking Your Restraint SystemsNow and then, make sure the safety belt reminder lightand all your belts, buckles, latch plates, retractors andanchorages are working properly. Look for any otherloose or damaged safety belt system parts. If you seeanything that might keep a safety belt system fromdoing its job, have it repaired.

Torn or frayed safety belts may not protect you in acrash. They can rip apart under impact forces. If a belt istorn or frayed, get a new one right away.

Also look for any opened or broken air bag covers, andhave them repaired or replaced. (The air bag systemdoes not need regular maintenance.)

Replacing Restraint System PartsAfter a CrashIf you’ve had a crash, do you need new belts?

After a very minor collision, nothing may be necessary.But if the belts were stretched, as they would be if wornduring a more severe crash, then you need new belts.

If belts are cut or damaged, replace them. Collisiondamage also may mean you will need to have safety beltor seat parts repaired or replaced. New parts and repairsmay be necessary even if the belt wasn’t being used atthe time of the collision.

If an air bag inflates, you’ll need to replace air bagsystem parts. See the part on the air bag system earlier inthis section.

yellowblue

1-66

✍ NOTES

2-

yellowblue

2-1

Section 2 Features and Controls

Here you can learn about the many standard and optional features on your vehicle, and information on starting,shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything isworking properly -- and what to do if you have a problem.

2-2 Keys2-3 Door Locks2-6 Keyless Entry System (If Equipped)2-9 Rear Access Door (Extended Cab)2-10 Tailgate2-11 Theft2-12 Content Theft-Deterrent (If Equipped)2-14 Passlock�2-14 New Vehicle “Break-In”2-15 Ignition Positions2-17 Starting Your Engine2-20 Engine Coolant Heater (If Equipped)2-21 Automatic Transmission Operation2-24 Manual Transmission Operation2-28 Four-Wheel Drive (If Equipped)2-34 Parking Brake2-35 Shifting Into PARK (P) (Automatic

Transmission Only)2-37 Shifting Out of PARK (P) (Automatic

Transmission Only)

2-38 Parking Your Vehicle (Manual TransmissionModels Only)

2-38 Parking Over Things That Burn2-39 Engine Exhaust2-39 Running Your Engine While You’re Parked

(Automatic Transmission)2-40 Manual Selectable Ride (If Equipped)2-41 Locking Rear Axle2-42 Windows2-44 Turn Signal/Multifunction Lever2-50 Exterior Lamps2-53 Interior Lamps2-54 Mirrors2-67 OnStar� System (Option)2-68 The Instrument Panel - Your

Information System2-70 Instrument Panel Cluster2-72 Warning Lights, Gages and Indicators2-85 Message Center

yellowblue

2-2

Keys

CAUTION:

Leaving children in a vehicle with the ignitionkey is dangerous for many reasons. A child orothers could be badly injured or even killed.

They could operate the power windows or othercontrols or even make the vehicle move. Don’tleave the keys in a vehicle with children.

yellowblue

2-3

Your vehicle has onedouble-sided key for theignition and all door locks.

Your vehicle may also havea key that locks and unlocksthe center floor consoleonly (if equipped).

If you ever lose your keys, your dealer will be able toassist you with obtaining replacements.

Door Locks

CAUTION:

Unlocked doors can be dangerous.

Passengers -- especially children -- can easilyopen the doors and fall out. When a door islocked, the inside handle won’t open it.

Outsiders can easily enter through an unlockeddoor when you slow down or stop your vehicle.This may not be so obvious: You increase thechance of being thrown out of the vehicle in acrash if the doors aren’t locked. Wear safety beltsproperly, lock your doors, and you will be farbetter off whenever you drive your vehicle.

yellowblue

2-4

There are several ways to lock and unlock your vehicle.

You can use the keyless entry system (if equipped).

You can also use your key.

Use only the key or the keyless entry transmitter if yourvehicle is equipped with the content theft-deterrentsystem and the system is on.

From the inside, to lock thedoor, slide the leverrearward. To unlock the door, slide the lever forward.

Power Door Locks (If Equipped)

If your vehicle has thispower door lock switch,press the raised side of theswitch, marked “L” oneither front door to lock allthe doors at once.

Press the recessed side of the switch marked “U” tounlock all the doors at once.

yellowblue

2-5

If your vehicle has thispower door lock switch,press the bottom of theswitch on either front doorto lock all the doors at once.

Press the top of the switch to unlock all the doors at once.

The power door locks will operate at any time withoutthe ignition being on.

The power door locks will also automatically lock whenthe vehicle reaches 15 mph (24 km/h). To unlock thedoors, refer to the instructions listed previously. Theautomatic locking feature can be disabled, if you prefer.See your dealer for assistance.

Operating the power locks may interact with thetheft-deterrent system (if equipped). See “ContentTheft-Deterrent” in the Index.

Programmable Automatic Door Locks (If Equipped)Your vehicle may be equipped with an auto lock/unlockfeature which enables you to program your power doorlocks. The following instructions detail how to programyour door locks.

To enter the program mode you need to:

1. Pull back on the the turn signal/multifunction leverall the way toward you and hold it while youperform the next step.

2. Beginning with the ignition in OFF, turn your key toON. Return it to OFF and turn to ON again. Thenreturn it to OFF. Once you do this, you will hear thelock switch lock and unlock.

3. You are now ready to program the automatic doorlocks. You will have ten seconds to program onceyou release the turn signal/multifunction lever.

The following is a list of the available programming options:

� Press the lock side of the lock switch on the driver’sside door panel once to turn on the automatic doorlock feature. All doors lock. No doors will unlock.

yellowblue

2-6

� Do the same twice to turn off the automatic doorlock feature. No doors will lock or unlock. Autounlocking will not work if auto locking is turned off.

� Press the unlock side of the lock switch on the doorpanel once to unlock the driver’s door and lock allother doors.

� Do the same twice to unlock all the doors. All doorslock and unlock. (This is the factory setting).

� Do the same three times to turn off the automaticdoor lock feature. No doors will lock or unlock.

You can exit the program mode any time by turning theignition to ON.

The automatic lock feature will lock all the doors when thevehicle speed is greater that 15 mph (24 km/h) for twoseconds. Your vehicle left the factory programmed to haveall the doors unlock once the key is removed from theignition and lock when vehicle speed exceeds 15 mph (24 km/h). See your dealer for more information.

If the lock/unlock switches are not pressed while in theprogramming mode, the respective auto lock/unlocksetting will not be modified.

Lockout PreventionTo protect you from locking your key in the vehicle, thisfeature stops the power door locks from locking whenthe keys are in the ignition and a door is open.

If the power lock switch is pressed when a door is openand the key is in the ignition, all of the doors will lockand then the driver’s door will unlock.

Keyless Entry System (If Equipped)If your vehicle has this feature, you can lock and unlockyour doors from about 3 feet (1 m) up to 100 feet (30 m)away using the remote keyless entry transmitter suppliedwith your vehicle.

Your keyless entry system operates on a radio frequencysubject to Federal Communications Commission (FCC)Rules and with Industry Canada.

This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interferencereceived, including interference that may causeundesired operation.

yellowblue

2-7

This device complies with RSS-210 of Industry Canada.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) thisdevice must accept any interference received, includinginterference that may cause undesired operation of the device.

Changes or modifications to this system by other than anauthorized service facility could void authorization touse this equipment.

At times you may notice a decrease in range. This isnormal for any remote keyless entry system. If thetransmitter does not work or if you have to stand closerto your vehicle for the transmitter to work, try this:

� Check the distance. You may be too far from yourvehicle. You may need to stand closer during rainyor snowy weather.

� Check the location. Other vehicles or objects may beblocking the signal. Take a few steps to the left orright, hold the transmitter higher, and try again.

� Check to determine if battery replacement orresynchronization is necessary. See the instructionsthat follow.

� If you’re still having trouble, see your dealer or aqualified technician for service.

OperationUNLOCK: Pressing this button once will unlock thedriver’s door. The parking lamps will flash and theinterior lights will come on. Pressing UNLOCK againwithin three seconds will cause the remaining doors tounlock. The parking lamps will flash and the interiorlights will come on.

LOCK: Pressing this button once will lock all of thedoors. Press LOCK again within three seconds and thehorn will chirp.

Operating the keyless entry transmitter may interactwith the theft-deterrent system. See “Content-TheftDeterrent” in the Index.

Remote Panic Alarm

When the button with the horn symbol on the keytransmitter is pressed, the horn will sound and theheadlamps and taillamps will flash for up to 30 seconds.This can be turned off by pressing the horn button again,waiting for 30 seconds, or starting the vehicle.

yellowblue

2-8

Matching Transmitter(s) To Your VehicleEach remote keyless entry transmitter is coded toprevent another transmitter from unlocking your vehicle.If a transmitter is lost or stolen, a replacement can bepurchased through your dealer. Remember to bring anyremaining transmitters with you when you go to yourdealer. When the dealer matches the replacementtransmitter to your vehicle, any remaining transmittersmust also be matched. Once your dealer has coded thenew transmitter, the lost transmitter will not unlock yourvehicle. Each vehicle can have only four transmittersmatched to it.

Battery ReplacementUnder normal use, the battery in your remote keylessentry transmitter should last about two years.

You can tell the battery is weak if the transmitter won’twork at the normal range in any location. If you have toget close to your vehicle before the transmitter works,it’s probably time to change the battery.

NOTICE:

When replacing the battery, use care not to touchany of the circuitry. Static from your bodytransferred to these surfaces may damage thetransmitter.

To replace the battery in the keyless entry transmitter:

yellowblue

2-9

1. Insert a dime in the slot between the covers of thetransmitter housing near the key ring hole. Removethe bottom by twisting the dime.

2. Remove and replace the battery with a three-voltCR2032 or equivalent battery, positive (+) side up.

3. Align the covers and snap them together.

4. Resynchronize the transmitter.

5. Check the operation of the transmitter.

ResynchronizationResynchronization may be necessary due to the securitymethod used by this system. The transmitter does notsend the same signal twice to the receiver. The receiverwill not respond to a signal that has been sentpreviously. This prevents anyone from recording andplaying back the signal from the transmitter.

To resynchronize your transmitter, stand close to yourvehicle and press and hold the LOCK and UNLOCKbuttons on the transmitter at the same time for sevenseconds. The door locks should cycle to confirmsynchronization. If the locks do not cycle, see yourdealer for service.

Rear Access Door (Extended Cab)Your vehicle is equipped with a rear access door thatallows easier access to the rear area of the extended cab.

To open a rear access doorfrom the outside, first openthe front door. Then, use thehandle located on the frontedge of the rear access doorto open it.

You must fully close a rear access door before you canclose the front door.

yellowblue

2-10

To open a rear access doorfrom the inside, the frontdoor must be opened first.Then, use the handle locatedon the inside of the rearaccess door to open it.

TailgateYou can open the tailgate by lifting up on its handlewhile pulling the tailgate toward you.

To shut the tailgate, firmly push it upward until it latches.

After you put the tailgate back up, pull it back towardsyou to be sure it latches securely.

Tailgate RemovalThe tailgate on your vehicle can be removed to allow fordifferent loading situations. Although the tailgate can beremoved without assistance, you may want someone toassist you with the removal to avoid possible damage tothe vehicle.

To remove the tailgate:

1. Raise the tailgateslightly and release bothretaining cable clips. Torelease the retainingcable clips, lift the cableso it points straight outand push the cable clip forward.

yellowblue

2-11

2. With the tailgate at aslight upward angle, pullback on the tailgate atthe right edge and thenmove the tailgate to theright to release the left edge.

Reverse the above procedure to reinstall. Make sure thetailgate is secure.

TheftVehicle theft is big business, especially in some cities.Although your vehicle has a number of theft-deterrentfeatures, we know that nothing we put on it can make itimpossible to steal. However, there are ways you can help.

Key in the IgnitionIf you leave your vehicle with the keys inside, it’s aneasy target for joy riders or professional thieves -- sodon’t do it.

When you park your vehicle and open the driver’s door,you’ll hear a chime reminding you to remove your keyfrom the ignition and take it with you. Always do this.Your steering wheel will be locked, and so will yourignition. If you have an automatic transmission, takingyour key out also locks your transmission. Alsoremember to lock the doors.

If the key is in the ignition, with any door open, and youtry to lock your doors with the power door locks, thedriver’s door will not stay locked. This will help to keepyou from locking your keys in the vehicle.

yellowblue

2-12

Parking at NightPark in a lighted spot, close all windows and lock yourvehicle. Remember to keep your valuables out of sight.Put them in a storage area, or take them with you.

Parking LotsIf you park in a lot where someone will be watchingyour vehicle, it’s best to lock it up and take your keys.But what if you have to leave your ignition key? What ifyou have to leave something valuable in your vehicle?

� Put your valuables in a storage area, like your glove box.

� Valuables can be locked in the center floor console.

� If your vehicle has a remote keyless entry system,take the transmitter with you.

� Lock all the doors except the driver’s.

Content Theft-Deterrent (If Equipped)Your vehicle may be equipped with a ContentTheft-Deterrent alarm system.

With this system, theSECURITY message willflash as you open the door(if your ignition is off).

This message reminds you to activate the theft-deterrentsystem. Here’s how to do it:

1. Open the door.

2. Lock the door with the power door lock switch or theremote keyless entry transmitter. The SECURITYmessage should come on and stay on. If using theremote keyless entry transmitter, the door does notneed to be open.

3. Close all doors. The SECURITY message should gooff after approximately 15 seconds. The alarm is notarmed until the SECURITY message goes off.

yellowblue

2-13

If a door is opened without the key or the remote keylessentry transmitter, the alarm will go off. Your vehicle’sheadlamps will flash and the horn will sound for abouttwo minutes, then will turn off to save the battery power.

Remember, the theft-deterrent system won’t activate ifyou lock the doors with a key or use the manual doorlock. It activates only if you use a power door lockswitch with the door open, or with the remote keylessentry transmitter. You should also remember that youcan start your vehicle with the correct ignition key if thealarm has been set off.

Here’s how to avoid setting off the alarm by accident:

� If you don’t want to activate the theft-deterrentsystem, the vehicle should be locked with the doorkey after the doors are closed.

� Always unlock a door with a key, or use the remotekeyless entry transmitter. Unlocking a door any other way will set off the alarm if the system has been armed.

If you set off the alarm by accident, unlock any doorwith the key. You can also turn off the alarm by pressingUNLOCK on the remote keyless entry transmitter or byplacing the key in the ignition and turning it to START.

Testing the AlarmThe alarm can be tested by following these steps:

1. From inside the vehicle, lower the driver’s windowand open the driver’s door.

2. Activate the system by locking the doors with thepower door lock switch while the door is open, orwith the remote keyless entry transmitter.

3. Get out of the vehicle, close the door and wait for theSECURITY message to go out.

4. Then reach in through the window, unlock the doorwith the manual door lock and open the door. Thisshould set off the alarm.

If the alarm does not sound when it should but thevehicle’s headlamps flash, check to see if the hornworks. The horn fuse may be blown. To replace the fuse,see “Fuses and Circuit Breakers” in the Index.

If the alarm does not sound or the vehicle’s headlampsdo not flash, the vehicle should be serviced by anauthorized service center.

yellowblue

2-14

Passlock�

Your vehicle is equipped with the Passlocktheft-deterrent system.

Passlock is a passive theft-deterrent system. Passlockenables fuel if the ignition lock cylinder is turned with avalid key. If a correct key is not used or the ignition lockcylinder is tampered with, fuel is disabled.

If the engine stalls and the SECURITY message flashes,wait until the light stops flashing before trying to restartthe engine. Remember to release the key from STARTas soon as the engine starts.

If the engine is running and the SECURITY messagecomes on, you will be able to restart the engine if youturn the engine off. However, your Passlock system isnot working properly and must be serviced by yourdealer. Your vehicle is not protected by Passlock at thistime. You may also want to check the fuse (see “Fusesand Circuit Breakers” in the Index). See your dealer for service.

In an emergency, call the GM Roadside AssistanceCenter. See “Roadside Assistance” in the Index.

New Vehicle “Break-In”

NOTICE:

Your vehicle doesn’t need an elaborate“break -in.” But it will perform better in the longrun if you follow these guidelines:

� Keep your speed at 55 mph (88 km/h) orless for the first 500 miles (805 km).

� Don’t drive at any one speed -- fast or slow -- for the first 500 miles (805 km).Don’t make full -throttle starts.

� Avoid making hard stops for the first 200 miles (322 km) or so. During this timeyour new brake linings aren’t yet brokenin. Hard stops with new linings can meanpremature wear and earlier replacement.Follow this breaking-in guideline everytime you get new brake linings.

� Don’t tow a trailer during break -in. See“Towing a Trailer” in the Index for more information.

yellowblue

2-15

Ignition PositionsYou can use your key to turn your ignition switch to fivedifferent positions.

ACCESSORY (A): ACCESSORY lets you use thingslike the radio, power windows and the windshieldwipers when the engine is off. Push in the key and turnit toward you. Your steering wheel will remain locked,just as it was before you inserted the key.

LOCK (B): This position locks your ignition, steeringwheel and transmission. It’s a theft-deterrent feature.You will only be able to remove your key when theignition is turned to LOCK.

OFF (C): This position lets you turn off the engine butstill turn the steering wheel. It doesn’t lock the steeringwheel like LOCK. Use OFF if you must have yourvehicle in motion while the engine is off (for example, ifyour vehicle is being pushed).

RUN (D): This is the position for driving.

START (E): This starts your engine.

CAUTION:

On manual transmission vehicles, turning the keyto LOCK will lock the steering column and resultin a loss of ability to steer the vehicle. This couldcause a collision. If you need to turn the engineoff while the vehicle is moving, turn the key onlyto OFF. Don’t press the key release button whilethe vehicle is moving.

yellowblue

2-16

NOTICE:

If your key seems stuck in LOCK and you can’tturn it, be sure you are using the correct key; ifso, is it all the way in? If it is, then turn thesteering wheel left and right while you turn thekey hard. But turn the key only with your hand.Using a tool to force it could break the key or theignition switch. If none of this works, then yourvehicle needs service.

Key Release Button (Manual Transmission)

The ignition key cannot beremoved from the ignitionof manual transmissionvehicles unless the keyrelease button is used.

To remove the key on manual transmission vehicles,turn the key to OFF, then press the button and turn thekey to LOCK. Do not hold the button in while turningthe key to OFF. Pull the key straight out.

Retained Accessory Power (If Equipped)Your vehicle may be equipped with a RetainedAccessory Power (RAP) feature which will allowcertain features on your vehicle to continue to work upto 20 minutes after the ignition key is turned to OFF.

Your radio, power windows and overhead console willwork when the ignition key is in RUN or ACCESSORY.Once the key is turned from RUN to OFF, these featureswill continue to work for up to 20 minutes or until adoor is opened.

yellowblue

2-17

Starting Your EngineAutomatic TransmissionMove your shift lever to PARK (P) or NEUTRAL (N).Your engine won’t start in any other position -- that’s asafety feature. To restart when you’re already moving,use NEUTRAL (N) only.

NOTICE:

Don’t try to shift to PARK (P) if your vehicle ismoving. If you do, you could damage thetransmission. Shift to PARK (P) only when yourvehicle is stopped.

Manual TransmissionThe gear selector should be in NEUTRAL and theparking brake engaged. Hold the clutch pedal to thefloor and start the engine. Your vehicle won’t start if theclutch pedal is not all the way down -- that’s a safety feature.

Starting Your V8 Engine1. Without pushing the accelerator pedal, turn the

ignition key to START. When the engine starts, letgo of the key. The idle speed will go down as yourengine gets warm.

NOTICE:

Holding your key in START for longer than 15 seconds at a time will cause your battery to bedrained much sooner. And the excessive heat candamage your starter motor. Wait about 15 seconds between each try to help avoiddraining your battery or damaging your starter.

2. If it doesn’t start within 10 seconds, push theaccelerator pedal all the way to the floor, while youhold the ignition key in START. When the enginestarts, let go of the key and let up on the acceleratorpedal. Wait about 15 seconds between each try tohelp avoid draining your battery or damaging your starter.

yellowblue

2-18

When starting your engine in very cold weather (below0�F or -18�C), do this:

1. With your foot off the accelerator pedal, turn theignition key to START and hold it there. When theengine starts, let go of the key. Use the acceleratorpedal to maintain engine speed, if you have to, untilyour engine has run for a while.

2. If your engine still won’t start (or starts but thenstops), it could be flooded with too much gasoline.Try pushing your accelerator pedal all the way to thefloor and holding it there as you hold the key inSTART for about three seconds. When the enginestarts, let go of the key and accelerator. If the vehiclestarts briefly but then stops again, do the same thing,but this time keep the pedal down for five or sixseconds. This clears the extra gasoline from the engine.

NOTICE:

Your engine is designed to work with theelectronics in your vehicle. If you add electricalparts or accessories, you could change the waythe engine operates. Before adding electricalequipment, check with your dealer. If you don’t,your engine might not perform properly.If you ever have to have your vehicle towed, seethe part of this manual that tells how to do itwithout damaging your vehicle. See “TowingYour Vehicle” in the Index.

yellowblue

2-19

Starting Your V6 Engine1. Without pushing the accelerator pedal, turn your

ignition key to START. When the engine starts, letgo of the key. The idle speed will go down as yourengine gets warm.

NOTICE:

Holding your key in START for longer than 15seconds at a time will cause your battery to bedrained much sooner. And the excessive heat candamage your starter motor. Wait about 15seconds between each try to help avoid drainingyour battery or damaging your starter.

2. If it doesn’t start right away, hold your key inSTART. If it doesn’t start in 10 seconds, push theaccelerator pedal all the way down for five moreseconds, unless it starts sooner.

3. If your engine still won’t start (or starts but thenstops), wait 15 seconds and start over.

When the engine starts, let go of the key and theaccelerator pedal.

NOTICE:

Your engine is designed to work with theelectronics in your vehicle. If you add electricalparts or accessories, you could change the waythe engine operates. Before adding electricalequipment, check with your dealer. If you don’t,your engine might not perform properly.If you ever have to have your vehicle towed, seethe part of this manual that tells how to do itwithout damaging your vehicle. See “TowingYour Vehicle” in the Index.

yellowblue

2-20

Engine Coolant Heater (If Equipped)In very cold weather, 0�F(-18�C) or colder, theengine coolant heater canhelp. You’ll get easierstarting and better fueleconomy during enginewarm-up. Usually, thecoolant heater should beplugged in a minimum offour hours prior to startingyour vehicle.

To Use the Engine Coolant Heater1. Turn off the engine.

2. Open the hood and unwrap the electrical cord. Thecord is located on the driver’s side of the enginecompartment, near the power steering fluid reservoir.

3. Plug it into a normal, grounded 110-volt AC outlet.

CAUTION:

Plugging the cord into an ungrounded outletcould cause an electrical shock. Also, the wrongkind of extension cord could overheat and causea fire. You could be seriously injured. Plug thecord into a properly grounded three-prong110-volt AC outlet. If the cord won’t reach, use aheavy-duty three-prong extension cord rated forat least 15 amps.

4. Before starting the engine, be sure to unplug andstore the cord as it was before to keep it away frommoving engine parts. If you don’t, it could be damaged.

How long should you keep the coolant heater pluggedin? The answer depends on the outside temperature, thekind of oil you have, and some other things. Instead oftrying to list everything here, we ask that you contactyour dealer in the area where you’ll be parking yourvehicle. The dealer can give you the best advice for thatparticular area.

yellowblue

2-21

Automatic Transmission Operation

There are several different positions for your shift lever.

If your vehicle is equipped with an automatictransmission, it features an electronic shift positionindicator within the instrument panel cluster. Thisdisplay must be powered anytime the shift lever iscapable of being moved out of PARK (P). This meansthat if your key is in OFF, rather than LOCK, there willbe a small current drain on your battery which coulddischarge your battery over a period of time. If you haveto leave your key in the ignition in OFF for an extendedperiod, it is recommended that you remove the IGN 0fuse from the instrument panel fuse block. See “Fusesand Circuit Breakers” in the Index.

PARK (P): This locks your rear wheels. It’s the bestposition to use when you start your engine because yourvehicle can’t move easily.

CAUTION:

It is dangerous to get out of your vehicle if theshift lever is not fully in PARK (P) with theparking brake firmly set. Your vehicle can roll.

Don’t leave your vehicle when the engine isrunning unless you have to. If you have left theengine running, the vehicle can move suddenly.You or others could be injured. To be sure yourvehicle won’t move, even when you’re on fairlylevel ground, always set your parking brake andmove the shift lever to PARK (P).If you have four-wheel drive, your vehicle will be free to roll -- even if your shift lever is inPARK (P) -- if your transfer case is inNEUTRAL (N). So, be sure the transfer case is ina drive gear, two-wheel high (2H) or four-wheelhigh (4H) or four-wheel low (4L) -- not inNEUTRAL (N). See “Shifting Into PARK (P)” inthe Index. If you’re pulling a trailer, see “Towinga Trailer” in the Index.

yellowblue

2-22

REVERSE (R): Use this gear to back up.

NOTICE:

Shifting to REVERSE (R) while your vehicle ismoving forward could damage yourtransmission. Shift to REVERSE (R) only afteryour vehicle is stopped.

To rock your vehicle back and forth to get out of snow,ice or sand without damaging your transmission, see“Stuck: In Sand, Mud, Ice or Snow” in the Index.

NEUTRAL (N): In this position, your engine doesn’t connect with the wheels. To restart when you’realready moving, use NEUTRAL (N) only. Also, useNEUTRAL (N) when your vehicle is being towed.

CAUTION:

Shifting out of PARK (P) or NEUTRAL (N) whileyour engine is “racing” (running at high speed) isdangerous. Unless your foot is firmly on thebrake pedal, your vehicle could move veryrapidly. You could lose control and hit people orobjects. Don’t shift out of PARK (P) orNEUTRAL (N) while your engine is racing.

NOTICE:

Damage to your transmission caused by shiftingout of PARK (P) or NEUTRAL (N) with theengine racing isn’t covered by your warranty.

yellowblue

2-23

DRIVE (D): This position is for normal driving. If youneed more power for passing, and you’re:

� Going less than about 35 mph (56 km/h), push youraccelerator pedal about halfway down.

� Going about 35 mph (56 km/h) or more, push theaccelerator all the way down.

You’ll shift down to the next gear and have more power.

DRIVE (D) can be used when towing a trailer, carryinga heavy load, driving on steep hills or for off-roaddriving. You may want to shift the transmission toTHIRD (3) or, if necessary, a lower gear selection if thetransmission shifts too often.

THIRD (3): This position is also used for normaldriving, however it offers more power and lower fueleconomy than DRIVE (D).

SECOND (2): This position gives you more power butlower fuel economy. You can use SECOND (2) on hills.It can help control your speed as you go down steepmountain roads, but then you would also want to useyour brakes off and on.

If you manually select SECOND (2) in a light dutyautomatic transmission, the transmission will drive insecond gear. You may use this feature for reducing thespeed of the rear wheels when you are trying to startyour vehicle from a stop on slippery road surfaces.

FIRST (1): This position gives you even more power(but lower fuel economy) than SECOND (2). You canuse it on very steep hills, or in deep snow or mud. If theselector lever is put in FIRST (1) while the vehicle ismoving forward, the transmission won’t shift into firstgear until the vehicle is going slowly enough.

NOTICE:

If your rear wheels can’t rotate, don’t try todrive. This might happen if you were stuck invery deep sand or mud or were up against a solidobject. You could damage your transmission.Also, if you stop when going uphill, don’t holdyour vehicle there with only the acceleratorpedal. This could overheat and damage thetransmission. Use your brakes or shift into PARK (P) to hold your vehicle in position on a hill.

On cold days, approximately 32�F (0�C) or colder, yourtransmission is designed to shift differently until theengine reaches normal operating temperature. This isintended to improve heater performance.

yellowblue

2-24

Tow/Haul Mode Selector Switch (Automatic Transmission)

Your vehicle is equipped with a tow/haul mode. Theselector switch is located on the end of the column shiftlever. You can use this feature to assist when towing orhauling a heavy load. See “Tow/Haul Mode” in theIndex for more information.

Manual Transmission Operation5-Speed (VORTEC 6000 V8 Engine)

Here’s how to operate your transmission.

FIRST (1) is intended only for heavy loads or trailertowing and is not recommended for normal driving.

During the first 500 miles (805 km) of vehicle use, startyour vehicle moving in FIRST (1). This allows clutchcomponents to break-in properly.

FIRST (1): Press the clutch pedal and shift into FIRST (1). Then, slowly let up on the clutch pedal asyou press the accelerator pedal. Shift into FIRST (1)only when the vehicle is below 5 mph (8 km/h). If youtry to shift down into FIRST (1) at excessive vehiclespeeds, the shift lever will not move into the FIRST (1)position until vehicle speed is reduced.

yellowblue

2-25

SECOND (2): Press the clutch pedal and shift intoSECOND (2). Then, slowly let up on the clutch pedal asyou press the accelerator pedal.

You can shift into SECOND (2) when you’re going lessthan 20 mph (32 km/h). If you’ve come to a completestop and it’s hard to shift into SECOND (2), put the shift lever into NEUTRAL (N) and let up on the clutch.Press the clutch pedal back down. Then shift into SECOND (2). If you try to downshift into SECOND (2)at excessive vehicle speeds, the shift lever will not moveinto the SECOND (2) position until the vehicle speed is reduced.

THIRD (3): Press the clutch pedal and shift intoTHIRD (3). Then, slowly let up on the clutch pedal asyou press the accelerator pedal.

FOURTH (4) and FIFTH (5): Shift into the higherforward gears the same way you do for THIRD (3).Slowly let up on the clutch pedal as you press theaccelerator pedal.

To stop, let up on the accelerator pedal and press thebrake pedal. Just before the vehicle stops, press theclutch pedal and the brake pedal, and shift toNEUTRAL (N).

NEUTRAL (N): Use this position when you start oridle your engine.

REVERSE (R): To back up, first press down the clutchpedal. Wait for the vehicle to stop moving and then, shiftinto REVERSE (R). Let up on the clutch pedal slowlywhile pressing the accelerator pedal.

NOTICE:

Shift to REVERSE (R) only after your vehicle isstopped. Shifting to REVERSE (R) while yourvehicle is moving could damage your transmission.

Also, use REVERSE (R), along with the parking brake,when turning off your engine and parking your vehicle.

yellowblue

2-26

5-Speed (VORTEC 4300 V6 and 4800 V8 Engines)Here’s how to operate your transmission:

FIRST (1): Press the clutch pedal and shift into FIRST (1). Then, slowly let up on the clutch pedal asyou press the accelerator pedal.

You can shift into FIRST (1) when you’re going lessthan 20 mph (32 km/h). If you’ve come to a completestop and it’s hard to shift into FIRST (1), put the shiftlever into NEUTRAL (N) and let up on the clutch. Pressthe clutch pedal back down. Then shift into FIRST (1).

SECOND (2): Press the clutch pedal as you let up on the accelerator pedal and shift into SECOND (2).Then, slowly let up on the clutch pedal as you press theaccelerator pedal.

THIRD (3), FOURTH (4) and FIFTH (5): Shift intoTHIRD (3), FOURTH (4) and FIFTH (5) the same wayyou do for SECOND (2). Slowly let up on the clutchpedal as you press the accelerator pedal.

To stop, let up on the accelerator pedal and press thebrake pedal. Just before the vehicle stops, press theclutch pedal and the brake pedal, and shift toNEUTRAL (N).

NEUTRAL (N): Use this position when you start oridle your engine.

REVERSE (R): To back up, first press down the clutchpedal. Wait for the vehicle to stop moving and then, shiftinto REVERSE (R). Let up on the clutch pedal slowlywhile pressing the accelerator pedal.

NOTICE:

Shift to REVERSE (R) only after your vehicle isstopped. Shifting to REVERSE (R) while yourvehicle is moving could damage your transmission.

Also, use REVERSE (R), along with the parking brake,when turning off your engine and parking your vehicle.

yellowblue

2-27

Shift Speeds

CAUTION:

If you skip a gear when you downshift, you couldlose control of your vehicle. You could injureyourself or others. Don’t shift down more thanone gear at a time when you downshift.

If your engine speed drops below 600 RPM, or if theengine is not running smoothly, you should downshift tothe next lower gear.

Shift Light

If you have a manualtransmission, you may havea SHIFT light. This lightwill show you when to shiftto the next higher gear forbest fuel economy.

When this light comes on, you can shift to the nexthigher gear if weather, road and traffic conditions allow.For the best fuel economy, accelerate slowly and shiftwhen the light comes on.

While you accelerate, it is normal for the light to go on and off if you quickly change the position of the accelerator.

If your vehicle has four-wheel drive and is equippedwith a manual transmission, disregard the SHIFT lightwhen the transfer case is in 4-Wheel Low.

Ignore the SHIFT light when you downshift.

yellowblue

2-28

Four-Wheel Drive (If Equipped)If your vehicle has four-wheel drive, you can send yourengine’s driving power to all four wheels for extratraction. To get the most satisfaction out of four-wheeldrive, you must be familiar with its operation. Read thepart that follows before using four-wheel drive. See theappropriate text for the transfer case in your vehicle.

NOTICE:

Driving in the 4-WHEEL HIGH (4H) or4-WHEEL LOW (4L) positions for a long timeon dry or wet pavement could shorten the life ofyour vehicle’s drivetrain.

Front Axle Locking FeatureThe front axle locks and unlocks automatically whenyou shift the transfer case. Some delay for the axle tolock or unlock is normal.

Manual Transfer Case (If Equipped)

The transfer case shift lever is on the floor to the right ofthe driver. Use this lever to shift into and out offour-wheel drive.

The 4WD indicator willlight up when you shift intofour-wheel drive and thefront axle engages.

Some delay between shifting and the indicator’s lightingis normal.

yellowblue

2-29

An indicator on the bezel near the lever shows you thetransfer case settings:

2-Wheel High (2H): This setting is used for driving inmost street and highway situations. Your front axle isnot engaged in two-wheel drive. This setting alsoprovides the best fuel economy.

4-Wheel High (4H): Use 4HI when you need extratraction, such as on snowy or icy roads or in mostoff-road situations. This setting also engages your frontaxle to help drive your vehicle. This is the best setting touse when plowing snow.

CAUTION:

Shifting the transfer case to NEUTRAL (N) cancause your vehicle to roll even if the transmissionis in PARK (P), or if you have a manualtransmission, even if you are in gear. You orsomeone else could be seriously injured. Be sureto set the parking brake before placing thetransfer case in NEUTRAL (N). See “ParkingBrake” in the Index.

NEUTRAL (N): Shift to this setting only when yourvehicle needs to be towed. The ignition switch must bein the RUN position in order to shift the lever intoNEUTRAL (N). See “Recreational Vehicle Towing” or“Towing your Vehicle” in the Index.

4-Wheel Low (4L): This setting also engages your frontaxle and delivers extra torque. You may never need4LO. It sends maximum power to all four wheels. Youmight choose 4LO if you are driving off-road in deepsand, deep mud, deep snow and climbing or descendingsteep hills.

yellowblue

2-30

You can shift from 2-Wheel High (2H) to 4-Wheel High(4H) or from 4-Wheel High (4H) to 2-Wheel High (2H)while the vehicle is moving. Your front axle will engagefaster if you take your foot off of the accelerator for acouple of seconds after you shift. In extremely coldweather, it may be necessary to stop or slow the vehicleto shift into 4-Wheel High (4H).

To shift into or out of 4-Wheel Low (4L) or NEUTRAL (N):

1. Slow the vehicle to a roll, about 1 to 3 mph (2 to 5 km/h) and shift an automatic transmissioninto NEUTRAL (N), or with a manual transmission,press the clutch pedal.

2. Shift the transfer case shift lever in one continuous motion.

Don’t pause in NEUTRAL (N) as you shift the transfercase into 4-Wheel Low (4L), or your gears could clash.

Remember that driving in 4-Wheel High (4H) or4-Wheel Low (4L) may reduce fuel economy. Also,driving in four-wheel drive on dry pavement couldcause your tires to wear faster and make your transfercase harder to shift and run noisier.

Automatic Transfer Case (If Equipped)

The transfer case switchesare located to the left of theinstrument panel cluster.

Use these switches to shift into and out of four-wheel drive.

yellowblue

2-31

You can choose among four driving settings:

2HI: This setting is used for driving in most street andhighway situations. Your front axle is not engaged intwo-wheel drive. This setting also provides the best fuel economy.

AUTO 4WD: This setting is ideal for use when roadconditions are variable. When driving your vehicle inAUTO 4WD, the front axle is engaged, but the vehicle’spower is sent only to the rear wheels. When the vehiclesenses a loss of traction, the system will automaticallyengage four-wheel drive. Driving in this mode results inslightly lower fuel economy than 2HI.

4HI: Use 4HI when you need extra traction, such as on snowy or icy roads or in most off-road situations.This setting also engages your front axle to help driveyour vehicle. This is the best setting to use whenplowing snow.

4LO: This setting also engages your front axle anddelivers extra torque. You may never need 4LO. It sendsmaximum power to all four wheels. You might choose4LO if you are driving off-road in deep sand, deep mud,deep snow and climbing or descending steep hills.

CAUTION:

Shifting the transfer case to NEUTRAL cancause your vehicle to roll even if the transmissionis in PARK (P). You or someone else could beseriously injured. Be sure to set the parkingbrake before placing the transfer case inNEUTRAL. See “Parking Brake” in the Index.

NEUTRAL: Shift the vehicle’s transfer case toNEUTRAL only when towing your vehicle. See“Recreational Vehicle Towing” or “Towing YourVehicle” in the Index for more information.

yellowblue

2-32

Indicator lights in the switches show which setting youare in. The indicator lights will come on briefly whenyou turn on the ignition and one will stay on. If thelights do not come on, you should take your vehicle toyour dealer for service. An indicator light will flashwhile shifting the transfer case. It will remainilluminated when the shift is complete. If for somereason the transfer case cannot make a requested shift, itwill return to the last chosen setting.

If the SERVICE 4WD light stays on, you should takeyour vehicle to your dealer for service. See “Service4WD” in the Index for further information.

Shifting to 4HI or AUTO 4WD

Press and release the 4HI or AUTO 4WD switch. Thiscan be done at any speed (except when shifting from4LO), and the indicator light will flash while shifting. It will remain illuminated when the shift is completed.

Shifting to 2HI

Press and release the 2HI switch. This can be done atany speed (except when shifting from 4LO).

Shifting to 4LO

To shift to 4LO, the ignition must be in RUN and thevehicle must be stopped or moving less than 3 mph (4.8 km/h) with the transmission in NEUTRAL (N). Thepreferred method for shifting into 4LO is to have yourvehicle moving 1 to 2 mph (1.6 to 3.2 km/h). Press andrelease the 4LO switch. You must wait for the 4LOindicator light to stop flashing and remain illuminatedbefore shifting your transmission in gear.

If the 4LO switch is pressed when your vehicle is ingear and/or moving, the 4LO indicator light will flashfor 30 seconds and not complete the shift unless yourvehicle is moving less than 3 mph (4.8 km/h) and thetransmission is in NEUTRAL (N). After 30 seconds thetransfer case will return to the setting last chosen.

Shifting Out of 4LO

To shift from 4LO to 4HI, AUTO 4WD or 2HI yourvehicle must be stopped or moving less than 3 mph (4.8 km/h) with the transmission in NEUTRAL (N) andthe ignition in RUN. The preferred method for shiftingout of 4LO is to have your vehicle moving 1 to 2 mph(1.6 to 3.2 km/h). Press and release the 4HI, AUTO4WD or 2HI switch. You must wait for the 4HI, AUTO4WD or 2HI indicator light to stop flashing and remainilluminated before shifting your transmission into gear.

yellowblue

2-33

If the 4HI, AUTO 4WD or 2HI switch is pressed whenyour vehicle is in gear and/or moving, the 4HI, AUTO4WD or 2HI indicator light will flash for 30 seconds butwill not complete the shift unless your vehicle is movingless than 3 mph (4.8 km/h) and the transmission is inNEUTRAL (N).

Shifting to NEUTRAL

To shift the transfer case to NEUTRAL, first make surethe vehicle is parked so that it will not roll:

1. Set the parking brake.

2. Start the vehicle or turn the ignition to RUN.

3. Connect the vehicle to the towing vehicle.

4. Put the transmission in NEUTRAL (N).

5. Shift the transfer case to 2HI.

6. Simultaneously press and hold the 2HI and 4LObuttons for 10 seconds. The red NEUTRAL lightwill come on when the transfer case shift toNEUTRAL is complete.

7. Shift the transmission to REVERSE (R) for onesecond, then shift the transmission to DRIVE (D)for one second.

8. Turn the ignition to OFF.

9. Place the transmission shift lever in PARK (P).

10. Release the parking brake prior to towing.

Shifting Out of NEUTRAL

To shift out of NEUTRAL:

1. Set the parking brake and apply the regular brake pedal.

2. Shift the transmission to NEUTRAL (N) and turn theignition to RUN with the engine off.

3. Press the button for the desired transfer case shiftposition (2HI, 4HI, AUTO 4WD or 4LO).

4. After the transfer case has shifted out of NEUTRALthe red light will go out.

5. You may start the engine and shift the transmissionto the desired position.

yellowblue

2-34

Parking BrakeTo set the parking brake, hold the regular brake pedaldown with your right foot. Push down the parking brakepedal with your left foot.

If the ignition is on, the brake system warning light willflash. A chime will activate when the parking brake isapplied and the vehicle is moved at least 3 mph (5 km/h)for at least three seconds.

To release the parking brake, hold the regular brakepedal down. Pull the bottom edge of the lever, locatedabove the parking brake pedal, marked BRAKERELEASE, to release the parking brake.

If the ignition is on when the parking brake is released,the brake system warning light will go off.

NOTICE:

Driving with the parking brake on can causeyour rear brakes to overheat. You may have toreplace them, and you could also damage otherparts of your vehicle.

If you are towing a trailer and are parking on any hill,see “Towing a Trailer” in the Index. That section showswhat to do first to keep the trailer from moving.

yellowblue

2-35

Shifting Into PARK (P) (Automatic Transmission Only)

CAUTION:

It can be dangerous to get out of your vehicle ifthe shift lever is not fully in PARK (P) with theparking brake firmly set. Your vehicle can roll. Ifyou have left the engine running, the vehicle canmove suddenly. You or others could be injured.To be sure your vehicle won’t move, even whenyou’re on fairly level ground, use the steps thatfollow. With four -wheel drive if your transfercase is in NEUTRAL (N), your vehicle will be freeto roll, even if your shift lever is in PARK (P). So,be sure the transfer case is in a drive gear -- notin NEUTRAL (N). If you’re pulling a trailer, see“Towing a Trailer” in the Index.

1. Hold the brake pedal down with your right foot andset the parking brake.

2. Move the shift lever into PARK (P) position like this:

� Pull the shift lever toward you.

yellowblue

2-36

� Move the lever up as far as it will go.

3. Be sure the transfer case is in a drive gear -- not inNEUTRAL (N).

4. Turn the ignition key to LOCK.

5. Remove the key and take it with you. If you canleave your vehicle with the ignition key in yourhand, your vehicle is in PARK (P).

Leaving Your Vehicle With the EngineRunning (Automatic Transmission Only)

CAUTION:

It can be dangerous to leave your vehicle with theengine running. Your vehicle could movesuddenly if the shift lever is not fully in PARK (P)with the parking brake firmly set. If you havefour-wheel drive with a manual transfer caseshift lever and your transfer case is in NEUTRAL (N), your vehicle will be free to roll,even if your shift lever is in PARK (P). So be surethe transfer case is in a drive gear -- not inNEUTRAL (N). And, if you leave the vehicle withthe engine running, it could overheat and evencatch fire. You or others could be injured. Don’tleave your vehicle with the engine running unlessyou have to.

yellowblue

2-37

If you have to leave your vehicle with the enginerunning, be sure your vehicle is in PARK (P) and theparking brake is firmly set before you leave it. After youmove the shift lever into PARK (P), hold the regularbrake pedal down. Then, see if you can move the shiftlever away from PARK (P) without first pulling ittoward you. If you can, it means that the shift leverwasn’t fully locked into PARK (P).

Torque Lock (Automatic Transmission)If you are parking on a hill and you don’t shift yourtransmission into PARK (P) properly, the weight of thevehicle may put too much force on the parking pawl inthe transmission. You may find it difficult to pull theshift lever out of PARK (P). This is called “torque lock.”To prevent torque lock, set the parking brake and thenshift into PARK (P) properly before you leave thedriver’s seat. To find out how, see “Shifting Into PARK (P)” in the Index.

When you are ready to drive, move the shift lever out ofPARK (P) before you release the parking brake.

If torque lock does occur, you may need to have anothervehicle push yours a little uphill to take some of thepressure from the parking pawl in the transmission, soyou can pull the shift lever out of PARK (P).

Shifting Out of PARK (P) (Automatic Transmission Only)Your vehicle has an automatic transmission shift lockcontrol system. You have to fully apply your regularbrakes before you can shift from PARK (P) when theignition is in RUN. See “Automatic Transmission” inthe Index.

If you cannot shift out of PARK (P), ease pressure onthe shift lever and push the shift lever all the way upinto PARK (P) as you maintain brake application. Then, move the shift lever into the gear you want.

If you ever hold the brake pedal down but still can’tshift out of PARK (P), try this:

1. Turn the key to the OFF ignition position.

2. Apply and hold the brake until the end of Step 4.

3. Shift the vehicle to NEUTRAL (N).

4. Start the vehicle and then shift to the drive gear you want.

5. Have the system fixed as soon as you can.

yellowblue

2-38

Parking Your Vehicle (Manual Transmission Models Only)

CAUTION:

Shifting the transfer case to NEUTRAL (N) cancause your vehicle to roll even if the manualtransmission is in gear. You or someone else couldbe seriously injured. Be sure to set the parkingbrake before placing the transfer case inNEUTRAL (N). See “Parking Brake” in the Index.

Before you get out of your vehicle, put your manualtransmission in REVERSE (R), turn off the engine, andfirmly apply the parking brake.

If you are parking on a hill, or if you are pulling atrailer, see “Towing a Trailer” in the Index.

Parking Over Things That Burn

CAUTION:

Things that can burn could touch hot exhaustparts under your vehicle and ignite. Don’t parkover papers, leaves, dry grass or other things thatcan burn.

yellowblue

2-39

Engine Exhaust

CAUTION:

Engine exhaust can kill. It contains the gascarbon monoxide (CO), which you can’t see orsmell. It can cause unconsciousness and death.

You might have exhaust coming in if:� Your exhaust system sounds strange

or different.� Your vehicle gets rusty underneath.� Your vehicle was damaged in a collision.� Your vehicle was damaged when driving

over high points on the road or over road debris.

� Repairs weren’t done correctly.� Your vehicle or exhaust system had been

modified improperly.If you ever suspect exhaust is coming into your vehicle:� Drive it only with all the windows down to

blow out any CO; and� Have your vehicle fixed immediately.

Running Your Engine While You’reParked (Automatic Transmission)It’s better not to park with the engine running. But ifever you have to, here are some things to know.

CAUTION:

Idling the engine with the climate control systemoff could allow dangerous exhaust into yourvehicle (see the earlier Caution under “Engine Exhaust”).Also, idling in a closed-in place can let deadlycarbon monoxide (CO) into your vehicle even ifthe fan switch is at the highest setting. One placethis can happen is a garage. Exhaust -- with CO -- can come in easily. NEVER park in agarage with the engine running.Another closed-in place can be a blizzard. (See “Blizzard” in the Index.)

yellowblue

2-40

CAUTION:

It can be dangerous to get out of your vehicle ifthe shift lever is not fully in PARK (P) with theparking brake firmly set. Your vehicle can roll.Don’t leave your vehicle when the engine isrunning unless you have to. If you’ve left theengine running, the vehicle can move suddenly.You or others could be injured. To be sure yourvehicle won’t move, even when you’re on fairlylevel ground, always set your parking brake andmove the shift lever to PARK (P).Four-wheel drive vehicles with the transfer casein NEUTRAL (N) will allow the vehicle to roll,even if your shift lever is in PARK (P). So, besure the transfer case is in a drive gear -- not inNEUTRAL (N). Always set your parking brake.

Follow the proper steps to be sure your vehicle won’tmove. See “Shifting Into PARK (P)” in the Index.

If you’re pulling a trailer, see “Towing a Trailer” in the Index.

Manual Selectable Ride (If Equipped)The main function of this system is to provide superiorride comfort while trailering or fully loaded, as well asfor unloaded driving. This system also helps to provide:

� Improved trailering stability

� Improved handling response when trailering or fully loaded

This button is located on thecenter of the instrumentpanel near the radio. Press itto activate the selectableride setting as desired. Anindicator light near thebutton will illuminatewhenever the system is active.

yellowblue

2-41

It is recommended to use this system as follows:

� For optimum ride comfort in an unloaded vehicle thebutton should be out and the indicator light will notbe illuminated. This switch position indicatesNORMAL levels of ride control or damping.

� For optimum ride comfort when trailering, fullyloaded, driving off-road, or when personalpreferences demand more control the button shouldbe pressed in with the indicator light illuminated.This switch position indicates FIRM levels of ridecontrol or damping.

The following guide can also be used to help determinethe best setting.

NORMAL: The indicator light will be off when thesystem is in this setting. Use for normal city andhighway driving. Provides a smooth, soft ride when thevehicle is unloaded.

FIRM (Unloaded): Press the switch to activate thissetting, the indicator light will illuminate. Use thissetting when road conditions or personal preferencedemand more control. Provides more “feel” or responseto the road conditions.

FIRM (Loaded): Press the switch to activate thissetting, the indicator light will illuminate. Use thissetting to minimize trailer inputs to the vehicle or whenthe vehicle is fully loaded. This setting is alsoappropriate for off-road driving.

You can select a setting at any time based on road andtrailering conditions to provide the best ride andhandling. Select a new setting whenever drivingconditions change.

Locking Rear AxleIf your vehicle has this feature, your locking rear axlecan give you additional traction on snow, mud, ice, sandor gravel. It works like a standard axle most of the time,but when one of the rear wheels has no traction and theother does, this feature will allow the wheel withtraction to move the vehicle.

yellowblue

2-42

WindowsManual WindowsTurn the hand crank on each door to raise or lowermanual windows.

Power Windows (If Equipped)

If you have the optionalpower windows, thecontrols are located on eachof the side doors.

The driver’s door has a switch for the passenger windowas well. Your power windows will work when theignition has been turned to ACCESSORY or RUN orwhen Retained Accessory Power (RAP) is present. See“Retained Accessory Power” in the Index.

Press the rear of the switch with the power windowsymbol on it to lower the window.

Press the front of the switch with the power windowsymbol on it to raise the window.

The driver’s window also has an express down featurethat allows the window to be lowered without holdingthe switch. Press and hold the rear of the window switchfor one second to activate the express down mode. Theexpress down mode can be canceled at any time bypressing the opposite side of the switch. To open thewindow partway, lightly tap the switch until the windowis at the desired position.

yellowblue

2-43

Swing-Out Windows (Extended Cab)To open a rear swing-outwindow, just flip the latchopen and swing the glass out.

The latch will catch when the window is fully open andhold the window in the open position.

Sliding Rear Window (If Equipped)To open the sliding rear window, unlock the latch leverby pushing the lever toward the passenger’s side of thevehicle. Release the lever from the latch plate and slidethe window toward the passenger’s side of the vehicle.

To close the window, slide the window toward thedriver’s side of the vehicle. The latch lever willautomatically snap on to the latch plate. Try to open thewindow without releasing the latch lever to be sure thewindow is in the locked position.

HornTo sound the horn, press the center pad on the steering wheel.

Tilt Wheel (If Equipped)The tilt steering wheelallows you to adjust thesteering wheel before you drive.

You can also raise it to the highest level to give yourlegs more room when you enter and exit the vehicle.

To tilt the wheel, hold the steering wheel and pull thelever. Move the steering wheel to a comfortable level,then release the lever to lock the wheel in place.

yellowblue

2-44

Turn Signal/Multifunction Lever

The lever on the left side of the steering columnincludes your:

� Turn Signal and Lane Change Indicator

� Headlamp High/Low Beam Changer

� Flash-to-Pass

� Windshield Wipers

� Windshield Washer

� Cruise Control (If Equipped)

Turn Signal and Lane Change SignalsThe turn signal has two upward (for right) and twodownward (for left) positions. These positions allow youto signal a turn or a lane change.

To signal a turn, move the lever all the way up or down. When the turn is finished, the lever will return automatically.

An arrow on the instrumentpanel will flash in thedirection of the turn or lane change.

To signal a lane change, just raise or lower the leveruntil the arrow starts to flash. Hold it there until youcomplete your lane change. The lever will return byitself when you release it.

If you move the lever all the way up or down, and the arrow flashes at twice the normal rate, a signal bulb may be burned out and other drivers may not see your turn signal.

If a bulb is burned out, replace it to help avoid anaccident. If the arrows don’t go on at all when yousignal a turn, check for burned-out bulbs and a blownfuse (see “Fuses and Circuit Breakers” in the Index).

yellowblue

2-45

Turn Signal On Chime

If your turn signal is left on for more than 3/4 of a mile(1.2 km), a chime will sound at each flash of the turnsignal. To turn off the chime, move the turn signal leverto the off position.

Headlamp High/Low Beam ChangerTo change the headlamps from low to high beam or highto low beam, pull the multifunction lever all the waytoward you. Then release it.

When the high beams are on, this light on theinstrument panel also will be on.

Flash-To-Pass FeatureThis feature allows you to use your high-beamheadlamps to signal a driver in front of you that youwant to pass. It works even if your headlamps are off.

To use it, pull the turn signal lever toward you, but notso far that you hear it click.

If your headlamps are off or on low-beam, yourhigh-beam headlamps will turn on. They’ll stay on aslong as you hold the lever toward you and thehigh-beam indicator on the instrument panel will come on. Release the lever to turn the high-beamheadlamps off.

yellowblue

2-46

Windshield Wipers

You control the windshield wipers by turning the bandwith the wiper symbol on it.

For a single wiping cycle, turn the band to MIST. Holdit there until the wipers start, then let go. The wipers willstop after one wipe. If you want more wipes, hold theband on MIST longer.

You can set the wiper speed for a long or short delaybetween wipes. This can be very useful in light rain orsnow. Turn the band to choose the delay time. Thecloser to LO, the shorter the delay.

For steady wiping at low speed, turn the band awayfrom you to the LO position. For high-speed wiping,turn the band further, to HI. To stop the wipers, movethe band to the OFF position.

Be sure to clear ice and snow from the wiper bladesbefore using them. If they’re frozen to the windshield,carefully loosen or thaw them. If your blades do becomeworn or damaged, get new blades or blade inserts.

Windshield WasherThere is a paddle marked with the windshield washersymbol at the top of the multifunction lever. To spraywasher fluid on the windshield, push the paddle. Thewipers will clear the window and then either stop orreturn to your preset speed.

CAUTION:

In freezing weather, don’t use your washer untilthe windshield is warmed. Otherwise the washerfluid can form ice on the windshield, blockingyour vision.

yellowblue

2-47

Cruise Control

With cruise control, you canmaintain a speed of about25 mph (40 km/h) or morewithout keeping your footon the accelerator. This canreally help on long trips.Cruise control does notwork at speeds below about25 mph (40 km/h).

If you apply your brakes, or press the clutch pedal (if equipped), the cruise control will disengage.

CAUTION:

� Cruise control can be dangerous where youcan’t drive safely at a steady speed. So,don’t use your cruise control on windingroads or in heavy traffic.

� Cruise control can be dangerous onslippery roads. On such roads, fast changesin tire traction can cause needless wheelspinning, and you could lose control. Don’t use cruise control on slippery roads.

yellowblue

2-48

Setting Cruise Control

CAUTION:

If you leave your cruise control switch on whenyou’re not using cruise, you might hit a buttonand go into cruise when you don’t want to. Youcould be startled and even lose control. Keep thecruise control switch off until you want to usecruise control.

1. Move the cruise control switch to ON.

2. Get up to the speed you want.

3. Press in the SET button at the end of the lever andrelease it.

4. Take your foot off the accelerator pedal.

The CRUISE light on theinstrument panel willilluminate when the cruisecontrol is engaged.

Resuming a Set Speed

Suppose you set your cruise control at a desired speedand then you apply the brake or press the clutch pedal (if equipped). This, of course, disengages the cruisecontrol. But you don’t need to reset it.

Once you’re going about 25 mph (40 km/h) or more,you can move the cruise control switch from ON to R/A briefly.

You’ll go right back up to your chosen speed and stay there.

If you hold the switch at R/A briefly, the vehicle willkeep going faster until you release the switch or applythe brake. So unless you want to go faster, don’t hold theswitch at R/A.

yellowblue

2-49

Increasing Speed While Using Cruise Control

There are two ways to go to a higher speed:

� Use the accelerator pedal to get to the higher speed.Press the SET button at the end of the lever, thenrelease the button and the accelerator pedal. You’llnow cruise at the higher speed.

� Move the cruise switch from ON to R/A. Hold itthere until you get up to the speed you want, andthen release the switch. To increase your speed invery small amounts, move the switch to R/A briefly.Each time you do this, your vehicle will go about 1 mph (1.6 km/h) faster.

Reducing Speed While Using Cruise Control

� Press and hold the SET button at the end of the leveruntil you reach the lower speed you want, thenrelease it.

� To slow down in very small amounts, press the SETbutton briefly. Each time you do this, you’ll go about1 mph (1.6 km/h) slower.

Passing Another Vehicle While Using Cruise Control

Use the accelerator pedal to increase your speed. Whenyou take your foot off the pedal, your vehicle will slowdown to the cruise control speed you set earlier.

Using Cruise Control on Hills

How well your cruise control will work on hills dependsupon your speed, load and the steepness of the hills.When going up steep hills, you may want to step on theaccelerator pedal to maintain your speed. When goingdownhill, you may have to brake or shift to a lower gearto keep your speed down. Of course, applying the braketakes you out of cruise control. Many drivers find this tobe too much trouble and don’t use cruise control onsteep hills.

Ending Cruise Control

There are two ways to turn off the cruise control:

� Step lightly on the brake pedal.

� Step lightly on the clutch pedal (if equipped).

� Move the cruise control switch to OFF.

Erasing Speed Memory

When you turn off the cruise control or the ignition,your cruise control set speed memory is erased.

yellowblue

2-50

Exterior Lamps

Your parking lamp and headlamp switch is on thedriver’s side of your instrument panel.

Turn the knob clockwise to the parking lamps symbol tomanually turn on:

� Parking Lamps

� Sidemarker Lamps

� Taillamps

� License Plate Lamps

� Instrument Panel Lights

Turn the knob clockwise to the master lamps symbol toturn on all the lamps listed as well as the headlamps.

Turn the knob all the way counterclockwise to turn offyour lamps and put the system in auto headlamp mode.

Automatic Headlamp SystemWhen it is dark enough outside, your automaticheadlamp system will turn on your headlamps at thenormal brightness along with other lamps such as thetaillamps, sidemarker, parking lamps and the instrumentpanel lights. The radio lights will also be dim.

Your vehicle is equipped with a light sensor located onthe top of the instrument panel in the defroster grille. Besure it is not covered, or the system will be on wheneverthe ignition is on.

The system may also turn on your headlamps whendriving through a parking garage, heavy overcastweather or a tunnel. This is normal.

There is a delay in the transition between the daytime andnighttime operation of the Daytime Running Lamps(DRL) and the automatic headlamp systems so that drivingunder bridges or bright overhead street lights does notaffect the system. The DRL and automatic headlampsystem will only be affected when the light sensor sees achange in lighting lasting longer than the delay.

yellowblue

2-51

To idle your vehicle with the automatic headlampsystem off, set the parking brake while the ignition isoff. Then start your vehicle. The automatic headlampsystem will stay off until you release the parking brake.

As with any vehicle, you should turn on the regularheadlamp system when you need it.

Lamps On ReminderA reminder chime will sound when your headlamps orparking lamps are manually turned on and your ignitionis in OFF, LOCK or ACCESSORY. To disable thechime, rotate the thumbwheel all the way down. In theautomatic mode, the headlamps turn off once theignition key is in OFF.

Daytime Running LampsDaytime Running Lamps (DRL) can make it easier forothers to see the front of your vehicle during the day.DRL can be helpful in many different drivingconditions, but they can be especially helpful in theshort periods after dawn and before sunset.

The DRL system will come on when:

� the ignition is on,

� the headlamp switch is in automatic headlamp mode,

� the automatic transmission is not in PARK (P),

� the light sensor determines it is daytime and

� the parking brake is released.

When the DRL are on, only your DRL lamps will be on.The taillamps, sidemarker and other lamps won’t be on.The instrument panel won’t be lit up either.

When it begins to get dark, the automatic headlampsystem will switch from DRL to the headlamps or thelast chosen headlamp setting that was used.

When you turn the headlamp switch off, the headlampswill go off, and your DRL lamps will illuminate,provided it is not dark outside.

To idle an automatic transmission equipped vehicle withthe DRL off, set the parking brake. Shifting thetransmission into PARK (P) will also allow you to idlethe vehicle with the DRL off. The DRL will stay offuntil you release the parking brake or shift thetransmission out of PARK (P).

To idle a manual transmission equipped vehicle with theDRL off, set the parking brake. The DRL will stay offuntil you release the parking brake.

As with any vehicle, you should turn on the regularheadlamp system when you need it.

yellowblue

2-52

Fog Lamps (If Equipped)If you have fog lamps, use them for better vision infoggy or misty conditions. Your parking lamps and/orlow-beam headlamps must be on for your fog lamps to work.

The fog lamp switch islocated on the left side ofyour instrument panel.

Press the switch to turn the fog lamps on. Press theswitch again to turn them off. An indicator light willglow in the switch when the fog lamps are on.

Remember, fog lamps alone will not give off as muchlight as your headlamps. Never use your fog lamps inthe dark without turning on your headlamps.

The fog lamps will go off whenever your high-beamheadlamps come on. When the high beams go off, thefog lamps will come on again.

The fog lamps will be cancelled after the ignition isturned off. If you still want to use the fog lamps afteryou restart the vehicle, you will need to press the foglamp switch again.

Auxiliary Roof Mounted Lamp Switch (If Equipped)

This switch includes wiringprovisions for a dealer or aqualified service center toinstall an auxiliary rooflamp. This switch is locatedon the center of theinstrument panel near thecomfort controls.

When the switch wiring is connected to an auxiliary roofmounted lamp, pressing the button will activate the lampand illuminate an indicator light near the button.Pressing the button again will turn off the roof mounted lamp.

If your vehicle has this switch, your vehicle may havethe Snow Plow Prep Package. For further informationsee “Snow Plow Prep Package” in the Index.

yellowblue

2-53

Interior LampsInstrument Panel Intensity ControlThe instrument panel intensity control is located to theright of the headlamp switch.

Rotate the thumbwheel up to adjust the instrument panellights. To turn on the dome lamps (with the vehicledoors closed) rotate the thumbwheel all the way up.

Exit LightingWith exit lighting, the interior lamps will come on whenyou remove the key from the ignition. The lights willnot come on if the DOME OVERRIDE button is pressed in.

Illuminated EntryYour vehicle is equipped with an illuminated entry feature.

When the doors are opened, the dome lamps will comeon if the DOME OVERRIDE button is in the “out”position. If the DOME OVERRIDE button is pressed in,the lamps will not come on.

Front Reading Lamps (If Equipped)

If your vehicle has readinglamps, press the buttonlocated next to the lamp toturn the lamp on. The lampscan be adjusted to point inthe direction you want.

Press the button again to turn the lamp off.

Dome LampsThe dome lamps will come on when you open the doors.

You can also turn the dome lamps on by rotating thethumbwheel, located next to the parking/headlampsknob, all the way up. In this position, the dome lampswill remain on whether the doors are opened or closed.

You can use the DOME OVERRIDE button, locatedbelow the parking/headlamp knob, to set the domelamps to come on automatically when the doors areopened, or remain off. To turn the lamps off, press thebutton into the “in” position. With the button in this

yellowblue

2-54

position, the dome lamps will remain off when the doorsare open. To return the lamps to automatic operation,press the button again and return it to the “out” position.With the button in this position, the dome lamps willcome on when you open a door.

Cargo Lamp

Press the button to turn thecargo lamp on. Press thebutton again to turn it off.

A message in the instrumentcluster will come on anddisplay CARGO LAMP ONwhen the cargo lamp isturned on and the ignitionkey is turned to RUN.

Battery Run-Down ProtectionThis feature shuts off the dome, reading, glove box,cargo and underhood lamps if they are left on for morethan 40 minutes when the ignition is off. This will keepyour battery from running down.

MirrorsInside Day/Night Rearview Mirror

Pull the tab under the mirror toward you to reduce glarefrom headlamps behind you after dark. Push the tabaway from you for normal daytime operation.

yellowblue

2-55

Electrochromic Inside Rearview Mirrorwith Compass (If Equipped)When on, an electrochromic mirror automatically dimsto the proper level to minimize glare from lights behindyou after dark.

The mirror also includes an eight-point compass displayin the upper right corner of the mirror face. When on,the compass automatically calibrates as the vehicle is driven.

Mirror Operation

The right side of the switch located at the bottom of themirror turns the electrochromic mirror on and off. TheLED, located to the right of the switch, will come onwhen the electrochromic mirror is turned on. To turn themirror on, press and hold the MIRROR button for threeseconds. The mirror will darken and remain dark untilthe button is released. To turn the mirror off, press andrelease the MIRROR button.

yellowblue

2-56

Compass Operation

Press the COMP switch once briefly to turn the compasson or off.

When the ignition and the compass feature are on, thecompass will show two character boxes forapproximately two seconds. After two seconds, themirror will display the compass heading.

When cleaning the mirror, use a paper towel or similarmaterial dampened with glass cleaner. Do not sprayglass cleaner directly on the mirror as that may cause theliquid cleaner to enter the mirror housing.

Compass Calibration

The compass may need calibration if:

� After five seconds, the display does not show acompass heading (“N” for North, for example), theremay be a strong magnetic field interfering with thecompass. Such interference may be caused by amagnetic antenna mount, magnetic note pad holderor a similar magnetic item.

� The compass does not display the correct headingand the compass zone variance is set correctly.

In order to calibrate, the letter “C” must be displayed inthe mirror compass windows. If “C” is not displayed,push in the “COMP” button for approximately eightseconds or until the letter “C” is displayed.

The compass can be calibrated in one of two ways:

� Drive the vehicle in circles at five mph (8 km/h) orless until the display reads a direction, or

� Drive the vehicle on your everyday routine and afterseveral turns the compass will become calibrated andwill display a direction.

Compass Variance

The compass is set in zone eight upon leaving thefactory. It will be necessary to adjust the compass tocompensate for compass variance if you live outsidezone eight. Under certain circumstances, as during along distance cross-country trip, it will be necessary toadjust for compass variance. Compass variance is thedifference between earth’s magnetic north and truegeographic north. If not adjusted to account for compassvariance, your compass could give false readings.

yellowblue

2-57

To adjust for compass variance:

1. Press and hold the COMP button, located at thebottom of the mirror, for three seconds until a zonenumber appears in the display.

2. Find your current location and variance zone numberon the following zone map.

3. Press the COMP button on the bottom of the mirroruntil the new zone number appears in the display.After you stop pressing the button in, the display willshow a compass direction within a few seconds.

Electrochromic Inside Rearview Mirrorwith Compass and Temperature Display (If Equipped)When on, an electrochromic mirror automatically dimsto the proper level to minimize glare from lights behindyou after dark.

The mirror also includes a display in the upper rightcorner of the mirror face. This can be used as a compassor to indicate outside air temperature.

yellowblue

2-58

Temperature Display

The temperature can be displayed by pressing the TEMPside of the switch. Pressing the TEMP switch oncebriefly, will toggle the temperature reading on and off.To alternate the temperature reading between Fahrenheitand Celsius, press and hold the TEMP button for three seconds until the display blinks F� and C�. Press and release the TEMP switch to toggle betweenthe Fahrenheit and Celsius readings. After five secondsof inactivity, the display will return to a normaltemperature reading.

Press and release the TEMP switch to toggle thetemperature display between Fahrenheit or Celsius. If anabnormal reading is displayed, please consult your dealer.

Electrochromic Mirror Operation

The right side of the switch, labeled TEMP and locatedat the bottom of the mirror, turns the electrochromicmirror on and off. An indicator light, located to the right of the TEMP switch, will come on when theelectrochromic mirror is turned on. To turn the mirroron, press and hold the TEMP button for six seconds. To turn the mirror off, press and hold the TEMP buttonfor six seconds. The indicator light will turn off.

Compass Operation

Press the COMP switch once briefly to turn the compasson or off.

When the ignition and the compass feature are on, thecompass will show two character boxes forapproximately two seconds. After two seconds, themirror will display the compass heading.

When cleaning the mirror, use a paper towel or similarmaterial dampened with glass cleaner. Do not sprayglass cleaner directly on the mirror as that may cause theliquid cleaner to enter the mirror housing.

yellowblue

2-59

Compass Calibration

The compass may need calibration if:

� After five seconds, the display does not show acompass heading (“N” for North, for example), theremay be a strong magnetic field interfering with thecompass. Such interference may be caused by amagnetic antenna mount, magnetic note pad holderor a similar magnetic item.

� The compass does not display the correct headingand the compass zone variance is set correctly.

In order to calibrate, the letter “C” must be displayed inthe mirror compass windows. If “C” is not displayed,push in the “COMP” button for approximately eightseconds or until the letter “C” is displayed.

The compass can be calibrated in one of two ways:

� Drive the vehicle in circles at five mph (8 km/h) orless until the display reads a direction, or

� Drive the vehicle on your everyday routine and afterseveral turns the compass will become calibrated andwill display a direction.

Compass Variance

The mirror is set in zone eight upon leaving the factory.It will be necessary to adjust the compass to compensatefor compass variance if you live outside zone eight.Under certain circumstances, as during a long distancecross-country trip, it will be necessary to adjust forcompass variance. Compass variance is the differencebetween earth’s magnetic north and true geographicnorth. If not adjusted to account for compass variance,your compass could give false readings.

To adjust for compass variance:

1. Use the COMP button located at the bottom of the mirror.

2. Press and hold the COMP button for three secondsuntil a zone number appears in the display.

3. Find your current location and variance zone numberon the following zone map.

yellowblue

2-60

4. Press the COMP button on the bottom of the mirroruntil the new zone number appears in the display.After you stop pressing the button in, the display willshow a compass direction within a few seconds.

Outside Manual Adjust MirrorsAdjust your outside mirrors so you can just see the side ofyour vehicle and have a clear view of objects behind you.Some mirrors can be folded in, to enter narrow doorways.

The use of hood-mounted air deflectors and add-onconvex mirror attachments may adversely affect mirror performance.

Camper Type Outside Mirrors (If Equipped)

If your vehicle is equipped with camper type mirrors,they can be adjusted so you can have a clear view ofobjects behind you.

Pull out the mirror head to extend it for better visibilitywhen towing a trailer.

yellowblue

2-61

Electric Outside Rearview Mirrors (If Equipped)

The control is located on thedriver’s door armrest.

Move the upper control to the left or right to choose themirror you want to adjust, then press the arrows on thelower control pad to adjust the mirror.

Heated Outside Rearview Mirrors (If Equipped)The outside rearview mirrors with this option feature adefrost mode.

To turn on the defrost feature, press the rear windowdefogger button. See “Rear Window Defogger” in theIndex for further information.

Convex Outside MirrorYour passenger’s side mirror may be convex. A convexmirror’s surface is curved so you can see more from thedriver’s seat.

CAUTION:

A convex mirror can make things (like othervehicles) look farther away than they really are.If you cut too sharply into the right lane, youcould hit a vehicle on your right. Check yourinside mirror or glance over your shoulder beforechanging lanes.

yellowblue

2-62

Storage CompartmentsYour vehicle includes a number of storagecompartments for storage of often-used items.

Some vehicles have storage areas in the instrumentpanel. Use these spaces for items such as gloves or small books.

Some models have a storage pocket on each of the front doors.

Some vehicles have a storage area behind the seat.

Glove BoxTo open your glove box, pull the lever upward and pullthe door downward.

Center Overhead Console (If Equipped)Your vehicle may have an overhead console. The longoverhead console has three storage compartments insideit and the short overhead console has one compartmentinside it.

Installing a Garage Door Opener

If you have the long overhead console, a garage dooropener can be installed in the front overhead compartment.

1. To install the garage door opener, first open thecompartment door by pressing the release button forward.

2. Peel the protectivebacking from the hookand loop patch. Press itfirmly to the back ofyour garage door opener,as close to the center ofthe opener as possible.

3. Center the garage door opener activation button overthe console door button, and press the opener firmlyinto place.

The pegs inside the compartment door are used tomake sure the button on the compartment door willcontact the control button on the garage door opener.

yellowblue

2-63

4. Add one peg at a timeuntil the PUSH buttonon the compartmentdoor will operate thegarage door opener, withthe compartment doorclosed, when you press the button marked PUSH.

5. Now, with thecompartment doorclosed, press the buttonmarked PUSH again tomake sure the garagedoor opener operates properly.

With the garage door opener positioned properly and theright number of pegs in place, you should only have topress the PUSH button slightly to operate the opener.

6. Adjust the position of the garage door opener andadd or remove pegs, as needed, until the openeroperates properly.

yellowblue

2-64

Sunglasses Storage Compartment

If you have the long overhead console, the center overheadcompartment can be used to store your sunglasses.

To open the center compartment, press the releasebutton located at the rear of the compartment door.

Place your sunglasses in the compartment door with thelenses facing out.

The rear compartment can be used to store a small item,like a book.

To open the rear compartment, press the release buttonlocated at the rear of the compartment door.

Instrument Panel Cupholder (If Equipped)Your vehicle may have a cupholder in the middle of theinstrument panel.

To use the cupholder, pull the cupholder out of theinstrument panel.

To close the cupholder, push it back into the instrument panel.

yellowblue

2-65

Center Console Storage Area (If Equipped)Your vehicle may have a console compartment betweenthe bucket seats.

To open it, insert the console key into the lock andunlock the console. Press the button and swing theconsole lid open.The console has a place to store tissues, pens and a clipto hold business cards.

Your console may have a cupholder that swings downfor the rear seat passengers to use.

Your vehicle may have a compact disc holder in the console.

Armrest Storage Compartment (If Equipped)Your vehicle may have a center armrest storagecompartment in the front bench seat.

To open it, fold down the armrest and press the latchhandle located at the front of the armrest. Then, let thelid pop up and swing open.

The storage compartment has a cassette/compact discholder. The holder will store up to six compact disccases and five cassette tape cases or a total of 11 cassettetape cases.

If not used to store cassette or compact disc cases, thestorage area can be used to store a laptop computer.

The storage compartment also has a folding writingtable on top of the armrest lid.

To use the writing table, pull the latch at the rear of thetable and swing the writing table forward. Use it to holda pad of paper and a pen.

yellowblue

2-66

Ashtrays and Cigarette LighterFront AshtrayThe front ashtray is located near the center of theinstrument panel. Pull on the bottom of the ashtray doorto open it.

NOTICE:

If you store paper or other things that burn inyour ashtrays, they could be set on fire bycigarettes or other smoking materials. That couldcause a fire and possibly damage your vehicle. Donot store papers and other things that burn inyour ashtrays.

To remove the front ashtray, press the retainer springand pull the ashtray toward you. To replace the ashtray,place the ashtray on the slides at the side of its locationin the instrument panel. Then slide the ashtray back toits original position.

To use the cigarette lighter, push it in all the way, and letgo. When it’s ready, it will pop back out by itself.

NOTICE:

Holding a cigarette lighter in with your handwhile it’s heating can make it overload, damagingthe lighter and the heating element. Just push thelighter all the way in and let go. When it’s done,it will pop back by itself.

yellowblue

2-67

Accessory Power Outlets

Two auxiliary power outlets are located near thecigarette lighter. Use these outlets to power mobiletelephones or other devices designed to operate withvehicle electrical systems.

The cigarette lighter is designed to fit only in thereceptacle to the right of the accessory power outlets.

Sun VisorsTo block out glare, you can swing down the visors. Youcan also swing them out to help block glare at the frontand side windows.

Your driver’s side sun visor may have a clip to holdsmall items, such as maps or a thin notebook. Thepassenger’s side sun visor may have a vanity mirror.

Cellular Telephone (If Equipped)Your vehicle may be prewired for a cellular telephone.Please consult your GM dealer or a qualified servicecenter for further information.

OnStar� System (Option)OnStar� is a vehicle communications service whichmay be ordered through your dealer. The followingOnStar services are available 24 hours a day:

� Automatic Notification of Front Air BagDeployment

� Emergency Services

� Remote Door Unlock

� Roadside Assistance with Location

� Route Support

� Convenience Services

� Remote Diagnostics

� Hands-Free, Voice-Activated Cellular Telephone

For more information, contact your dealer.

yellowblue

2-68

The Instrument Panel - Your Information System

yellowblue

2-69

A. Dome Lamp Switch

B. Lamp Controls

C. Air Outlets

D. Automatic Transfer Case (If Equipped)

E. Multifunction Lever

F. Instrument Cluster

G. Gearshift Lever (Automatic Transmission)

H. Tow/Haul Selector Switch

I. Audio System

J. Comfort Control System

K. Glove Box

L. Passenger Air Bag Off Switch

M. Manual Selectable Ride Control (If Equipped)

N. Ashtray

O. Storage Area or Compact Disc Player (If Equipped)

P. Rear Window Defogger Switch (If Equipped)

Q. Lighter and Auxiliary Power Outlets

R. Parking Brake Release

S. Tilt Lever (If Equipped)

T. Center Instrument Panel Utility Block

U. Hood Release

V. Instrument Panel Fuse Block

yellowblue

2-70

Instrument Panel Cluster

United States Heavy Duty Automatic Transmission version shown, Canada, Light Duty Automatic and Manual Transmission clusters similar

Your instrument cluster is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’regoing, about how much fuel you have and many other things you’ll need to know to drive safely and economically.

yellowblue

2-71

Speedometer and OdometerYour speedometer lets you see your speed in both milesper hour (mph) and kilometers per hour (km/h). Yourodometer shows how far your vehicle has been driven,in either miles (used in the United States) or kilometers(used in Canada).

Trip Odometer

The trip odometer can tell you how far your vehicle hasbeen driven since you last set the trip odometer to zero.

Press the reset button to toggle between the tripodometer and the regular odometer. Holding the resetbutton for two seconds while the trip odometer isdisplayed will reset it.

To display the odometer reading with the ignition off,press the reset button.

Engine Hour Meter Display

The odometer can also display the number of hours theengine has run. To display the hour meter, turn theignition off, press and hold the reset button for at leastfour seconds. The hour meter will be displayed for up to30 seconds, or until the ignition is turned on.

TachometerYour tachometer displays the engine speed inrevolutions per minute (rpm).

NOTICE:

On vehicles with a manual transmission, if youoperate the engine with the tachometer in the redarea, your engine or other parts could be damaged.

Damage to your engine or vehicle caused byoperating the engine in the red area isn’t coveredby your vehicle warranty. Don’t operate theengine with the tachometer in the red area.

yellowblue

2-72

Warning Lights, Gages and IndicatorsThis part describes the warning lights and gages that maybe on your vehicle. The pictures will help you locate them.

Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to your warning lights and gages could also save you or others from injury.

Warning lights come on when there may be or is aproblem with one of your vehicle’s functions. As youwill see in the details on the next few pages, somewarning lights come on briefly when you start theengine just to let you know they’re working. If you arefamiliar with this section, you should not be alarmedwhen this happens.

Gages can indicate when there may be or is a problemwith one of your vehicle’s functions. Often gages andwarning lights work together to let you know whenthere’s a problem with your vehicle.

When one of the warning lights comes on and stays onwhen you are driving, or when one of the gages showsthere may be a problem, check the section that tells youwhat to do about it. Please follow this manual’s advice.Waiting to do repairs can be costly -- and evendangerous. So please get to know your warning lightsand gages. They’re a big help.

Your vehicle has a message center that works along withthe warning lights and gages. See “Message Center” inthe Index.

Safety Belt Reminder LightWhen the key is turned to RUN or START, a chime willcome on for about six seconds to remind people tofasten their safety belts, unless the driver’s safety belt isalready buckled.

The safety belt light will also come on and stayon for about 20 seconds,then it will flash for about55 seconds.

If the driver’s belt is already buckled, neither the chimenor the light will come on.

yellowblue

2-73

Air Bag Readiness LightThere is an air bag readiness light on the instrumentpanel, which shows the air bag symbol. The systemchecks the air bag’s electrical system for malfunctions.The light tells you if there is an electrical problem. Thesystem check includes the air bag sensors, the air bagmodules, the wiring, the passenger air bag suppressioncircuit and the crash sensing and diagnostic module. Formore information on the air bag system, see “Air Bag”in the Index.

This light will come onwhen you start your vehicle,and it will flash for a fewseconds. Then the lightshould go out. This meansthe system is ready.

If the air bag readiness light stays on after you start thevehicle or comes on when you are driving, your air bagsystem may not work properly. Have your vehicleserviced right away.

CAUTION:

If the air bag readiness light stays on after youstart your vehicle, it means the air bag systemmay not be working properly. The air bags inyour vehicle may not inflate in a crash, or theycould even inflate without a crash. To help avoidinjury to yourself or others, have your vehicleserviced right away if the air bag readiness lightstays on after you start your vehicle.

The air bag readiness light should flash for a fewseconds when you turn the ignition key to RUN. If thelight doesn’t come on then, have it fixed so it will beready to warn you if there is a problem.

yellowblue

2-74

AIR BAG OFF LightWhen you turn the right front passenger’s air bag off,this light will come on and stay on to remind you thatthe air bag has been turned off. This light will go offwhen you turn the air bag back on again. See “AIR BAGOFF Switch” in the Index for more on this, includingimportant safety information.

CAUTION:

If the right front passenger’s air bag is turned offfor a person who isn’t in a risk group identifiedby the national government, that person won’thave the extra protection of an air bag. In acrash, the air bag wouldn’t be able to inflate andhelp protect the person sitting there. Don’t turnoff the passenger’s air bag unless the personsitting there is in a risk group. See “AIR BAGOFF Switch” in the Index for more on this,including important safety information.

yellowblue

2-75

CAUTION:

If the air bag readiness light ever comes on whenyou have turned off the air bag, it means thatsomething may be wrong with the air bag system.The right front passenger’s air bag could inflateeven though the switch is off.

If your vehicle is a regular cab pickup and thisever happens, don’t let anyone whom thenational government has identified as a memberof a passenger air bag risk group sit in the rightfront passenger’s position (for example, don’tsecure a rear-facing child restraint in yourvehicle) until you have your vehicle serviced.

If your vehicle is an extended cab pickup and thisever happens, don’t let anyone whom thenational government has identified as a memberof a passenger air bag risk group sit in the rightfront passenger’s position (for example, don’tsecure a rear-facing child restraint in the rightfront passenger’s seat) until you have yourvehicle serviced.

Voltmeter

When your engine is notrunning, but the ignition isin RUN, this gage showsyour battery’s state ofcharge in DC volts.

When the engine is running, the gage shows thecondition of the charging system. Readings between thelow and high warning zones indicate the normaloperating range.

Readings in the low warning zone may occur when alarge number of electrical accessories are operating inthe vehicle and the engine is left at an idle for anextended period. This condition is normal since thecharging system is not able to provide full power atengine idle. As engine speeds are increased, thiscondition should correct itself as higher engine speedsallow the charging system to create maximum power.

yellowblue

2-76

You can only drive for a short time with the reading ineither warning zone. If you must drive, turn off allunnecessary accessories.

Readings in either warning zone indicate a possibleproblem in the electrical system. Have the vehicleserviced as soon as possible.

Shift Light (If Equipped)

This light is used on some models with manual transmissions.

The SHIFT indicator light will help you get the best fueleconomy. See “Shift Light” or “Shift Speeds” in theindex for more information.

Brake System Warning LightWith the ignition on, the brake system warning light will flash when you set the parking brake. The light willflash if the parking brake doesn’t release fully. If you try to drive with the parking brake engaged, a chime will sound when the vehicle speed is greater than 3 mph (5 km/h).

Your vehicle’s hydraulic brake system is divided intotwo parts. If one part isn’t working, the other part canstill work and stop you. For good braking, though, youneed both parts working well.

If the warning light comes on, there could be a brakeproblem. Have your brake system inspected right away.

This light should come on briefly when you turn the ignition key to RUN. If it doesn’t come on then,have it fixed so it will beready to warn you if there’sa problem.

yellowblue

2-77

If the light comes on while you are driving, pull off theroad and stop carefully. You may notice that the pedal isharder to push. Or, the pedal may go closer to the floor.It may take longer to stop. If the light is still on, have thevehicle towed for service. (See “Towing Your Vehicle”in the Index.)

CAUTION:

Your brake system may not be working properlyif the brake system warning light is on. Drivingwith the brake system warning light on can leadto an accident. If the light is still on after you’vepulled off the road and stopped carefully, havethe vehicle towed for service.

Anti-Lock Brake System Warning Light

With the anti-lock brakesystem, this light will comeon when you start yourengine and may stay on forseveral seconds. That’s normal.

If the light stays on, or comes on when you’re driving,your vehicle needs service. If the regular brake systemwarning light isn’t on, you still have brakes, but youdon’t have anti-lock brakes. If the regular brake systemwarning light is also on, you don’t have anti-lock brakesand there’s a problem with your regular brakes. See“Brake System Warning Light” earlier in this section.

The anti-lock brake system warning light should comeon briefly when you turn the ignition key to RUN. If thelight doesn’t come on then, have it fixed so it will beready to warn you if there is a problem.

yellowblue

2-78

Engine Coolant Temperature Gage

This gage shows the enginecoolant temperature.

It also provides an indicator of how hard your vehicle isworking. During a majority of the operation, the gagewill read 210�F (100�C) or less. If you are pulling aload or going up hills, it is normal for the temperature tofluctuate and approach the 250�F (122�C) mark. If thegage reaches the 260�F (125�C) mark, it indicates thatthe cooling system is working beyond its capacity.

The “Problems on the Road,” section of this manualshows what to do. See “Engine Overheating” in the Index.

Transmission Temperature Gage (If Equipped)

If your vehicle has a heavyduty automatic transmission,you will have a transmissiontemperature gage.

When your ignition is on, the gage shows thetemperature of the transmission fluid. The normaloperating range is from 100�F (38�C) to about 265�F (130�C).

At approximately 265�F (130�C), the message centerwill display a TRANS FLUID HOT message and thetransmission will enter a transmission protection mode.When the transmission enters the protection mode, youmay notice a change in the transmission shiftingpatterns. The transmission will return to normal shiftingpatterns when the transmission fluid temperature fallsbelow 260�F (127�C).

yellowblue

2-79

See “Message Center” in the Index for further information.

If the transmission fluid reaches temperatures ofapproximately 275�F (135�C) or greater, the messagecenter will display a TRANS HOT...IDLE ENG warningmessage. Pull the vehicle off the roadway when it is safeto do so. Set the parking brake, place the transmission inPARK (P) and allow the engine to idle until thetransmission temperature falls below 260�F (127�C). Ifthe transmission continues to operate above 265�F(130�C), please contact your nearest dealer or the GMRoadside Assistance Center.

NOTICE:

If you keep driving your vehicle with thetransmission temperature gage above the normaloperating range, you can damage thetransmission. This could lead to costly repairsthat may not be covered under your warranty.

The following situations can cause the transmission tooperate at higher temperatures:

� Towing a trailer

� Hot outside air temperatures

� Hauling a large or heavy load

� Low transmission fluid level

� High transmission fluid level

� Restricted air flow to the radiator and the auxiliarytransmission oil cooler (if equipped).

A temporary solution to hotter transmission operatingtemperatures may be to let the transmission cool down.If the transmission is operated at higher temperatures ona frequent basis, see “Scheduled Maintenance” in theIndex for the proper transmission maintenance intervals.

yellowblue

2-80

Malfunction Indicator Lamp (Service Engine Soon Light)

Your vehicle is equippedwith a computer whichmonitors operation of thefuel, ignition and emissioncontrol systems.

This system is called OBD II (On-BoardDiagnostics-Second Generation) and is intended toassure that emissions are at acceptable levels for the lifeof the vehicle, helping to produce a cleanerenvironment. The SERVICE ENGINE SOON lightcomes on to indicate that there is a problem and serviceis required. Malfunctions often will be indicated by thesystem before any problem is apparent. This mayprevent more serious damage to your vehicle. Thissystem is also designed to assist your service technicianin correctly diagnosing any malfunction.

NOTICE:

If you keep driving your vehicle with this lighton, after a while, your emission controls may notwork as well, your fuel economy may not be asgood and your engine may not run as smoothly.This could lead to costly repairs that may not becovered by your warranty.

NOTICE:

Modifications made to the engine, transmission,exhaust or fuel system of your vehicle or thereplacement of the original tires with other thanthose of the same Tire Performance Criteria(TPC) can affect your vehicle’s emission controlsand may cause the SERVICE ENGINE SOONlight to come on. Modifications to these systemscould lead to costly repairs not covered by yourwarranty. This may also result in a failure to passa required Emission Inspection/Maintenance test.

yellowblue

2-81

This light should come on, as a check to show you it isworking, when the ignition is on and the engine is notrunning. If the light doesn’t come on, have it repaired.This light will also come on during a malfunction in oneof two ways:

� Light Flashing -- A misfire condition has beendetected. A misfire increases vehicle emissions andmay damage the emission control system on yourvehicle. Dealer or qualified service center diagnosisand service may be required.

� Light On Steady -- An emission control systemmalfunction has been detected on your vehicle.Dealer or qualified service center diagnosis andservice may be required.

If the Light Is Flashing

The following may prevent more serious damage toyour vehicle:

� Reducing vehicle speed.

� Avoiding hard accelerations.

� Avoiding steep uphill grades.

� If you are towing a trailer, reduce the amount ofcargo being hauled as soon as it is possible.

If the light stops flashing and remains on steady, see “If the Light Is On Steady” following.

If the light continues to flash, when it is safe to do so,stop the vehicle. Find a safe place to park your vehicle.Turn the key off, wait at least 10 seconds and restart theengine. If the light remains on steady, see “If the LightIs On Steady” following. If the light is still flashing,follow the previous steps, and drive the vehicle to yourdealer or qualified service center for service.

If the Light Is On Steady

You may be able to correct the emission systemmalfunction by considering the following:

Did you recently put fuel into your vehicle?

If so, reinstall the fuel cap, making sure to fully installthe cap. See “Filling Your Tank” in the Index. Thediagnostic system can determine if the fuel cap has beenleft off or improperly installed. A loose or missing fuelcap will allow fuel to evaporate into the atmosphere. Afew driving trips with the cap properly installed shouldturn the light off.

Did you just drive through a deep puddle of water?

If so, your electrical system may be wet. The conditionwill usually be corrected when the electrical systemdries out. A few driving trips should turn the light off.

yellowblue

2-82

Have you recently changed brands of fuel?

If so, be sure to fuel your vehicle with quality fuel (see“Fuel” in the Index). Poor fuel quality will cause yourengine not to run as efficiently as designed. You maynotice this as stalling after start-up, stalling when youput the vehicle into gear, misfiring, hesitation onacceleration or stumbling on acceleration. (Theseconditions may go away once the engine is warmed up.)This will be detected by the system and cause the lightto turn on.

If you experience one or more of these conditions,change the fuel brand you use. It will require at least onefull tank of the proper fuel to turn the light off.

If none of the above steps have made the light turn off,have your dealer or qualified service center check thevehicle. Your dealer has the proper test equipment anddiagnostic tools to fix any mechanical or electricalproblems that may have developed.

Emissions Inspection and Maintenance Programs

Some state/provincial and local governments have ormay begin programs to inspect the emission controlequipment on your vehicle. Failure to pass thisinspection could prevent you from getting a vehicle registration.

Here are some things you need to know in order to helpyour vehicle pass an inspection:

Your vehicle will not pass this inspection if theSERVICE ENGINE SOON light is on or not working properly.

Your vehicle will not pass this inspection if the OBD(on-board diagnostic) system determines that criticalemission control systems have not been completelydiagnosed by the system. The vehicle would beconsidered not ready for inspection. This can happen ifyou have recently replaced your battery or if yourbattery has run down. The diagnostic system is designedto evaluate critical emission control systems duringnormal driving. This may take several days of routinedriving. If you have done this and your vehicle still doesnot pass the inspection for lack of OBD systemreadiness, see your dealer or qualified service center toprepare the vehicle for inspection.

yellowblue

2-83

Oil Pressure Gage

The oil pressure gage showsthe engine oil pressure in psi(pounds per square inch)when the engine is running.Canadian vehicles indicatepressure in kPa (kilopascals).

Oil pressure may vary with engine speed, outsidetemperature and oil viscosity, but readings above thelow pressure zone indicate the normal operating range.

A reading in the low pressure zone may be caused by adangerously low oil level or some other problemcausing low oil pressure. Check your oil as soon aspossible. See “Check Eng Oil Pressure” and “EngineOil” in the Index.

CAUTION:

Don’t keep driving if the oil pressure is low. Ifyou do, your engine can become so hot that itcatches fire. You or others could be burned.Check your oil as soon as possible and have yourvehicle serviced.

NOTICE:

Damage to your engine from neglected oilproblems can be costly and is not covered by your warranty.

yellowblue

2-84

Cruise Light (If Equipped)

The CRUISE light comeson whenever you set yourcruise control. See “CruiseControl” in the Index.

4WD Light (If Equipped)

The 4WD indicator willlight up when you shift amanual transfer case intofour-wheel drive and thefront axle engages.

Some delay between shifting and the indicator’s lightingis normal.

See “Four-Wheel Drive” in the Index for more information.

Tow/Haul Light (Automatic Transmissions Only)

This message is displayedwhen the tow/haul mode hasbeen activated.

For more information see, “Tow/Haul Mode” in the Index.

Fuel Gage

The fuel gage, when theignition is on, tells youabout how much fuel youhave left in your tank.

The gage will first indicate E (Empty) before you are out offuel, and you should get more fuel as soon as possible.

yellowblue

2-85

Here are some situations you may experience with yourfuel gage. None of these indicate a problem with the fuel gage.

� At the gas station, the fuel pump shuts off before thegage reads F (Full).

� It takes a little more or less fuel to fill up than thefuel gage indicated. For example, the gage may haveindicated the tank was half full, but it actually took alittle more or less than half the tank’s capacity to fillthe tank.

� The gage goes back to E (Empty) when you turn offthe ignition.

Message CenterThe message center is located on the left side of theinstrument panel cluster. It gives you important safetyand maintenance facts. When you turn the ignition on,the entire center lights up for just a few seconds. Asneeded, the message center will display one of thefollowing messages. The message center is capable ofalternating among different messages if needed.

BATTERY

If this message is displayedwhen the engine is running,you may have a problemwith your charging system.

The battery display will also stay on while the key is inRUN until the engine is started.

If the message stays on after starting the engine it couldindicate a problem with the generator drive belt, or someother charging system problem. Have it checked rightaway. Driving with this message displayed could drainyour battery.

If you must drive a short distance with this messagedisplayed, it helps to turn off all your accessories, suchas the radio and the air conditioner.

yellowblue

2-86

TRANS FLUID HOTIf you have an automatic transmission, you have atransmission temperature warning display contained inthe message center.

If the transmission fluidtemperature becomes high,the message center willdisplay this message.

When the transmission enters the protection mode youmay notice a change in the transmission shiftingpatterns. When the transmission fluid temperaturereturns to normal, the display will turn off and thetransmission shifting patterns will return to normal.

NOTICE:

If you keep driving your vehicle with thetransmission TRANS FLUID HOT messagedisplayed, you can damage the transmission. This could lead to costly repairs that may not becovered under your warranty.

The following situations can cause the transmission tooperate at higher temperatures:

� Towing a trailer

� Hot outside air temperatures

� Hauling a large or heavy load

� Low transmission fluid level

� High transmission fluid level

� Restricted air flow to the radiator and the auxiliarytransmission oil cooler (if equipped).

A temporary solution to hotter transmission operatingtemperatures may be to let the transmission cool down.If the transmission is operated at higher temperatures ona frequent basis, see “Scheduled Maintenance” in theIndex for the proper transmission maintenance intervals.

yellowblue

2-87

TRANS HOT...IDLE ENGINEIf you have an automatic transmission, you have atransmission over-temperature display contained in themessage center.

If this warning message isdisplayed, pull the vehicleoff the roadway when it issafe to do so.

Set the parking brake and place the transmission inPARK (P). Idle the engine until the message center nolonger displays a message. If idling the engine does notturn the warning message off after 10 to 15 minutes,contact your nearest dealer or the GM RoadsideAssistance Center. See “Roadside Assistance” in the Index.

NOTICE:

If you keep driving your vehicle with thetransmission TRANS HOT...IDLE ENGINEmessage displayed, you can damage thetransmission. This could lead to costly repairsthat may not be covered under your warranty.

The following situations can cause the transmission tooperate at higher temperatures:

� Towing a trailer

� Hot outside air temperatures

� Hauling a heavy load

� Low transmission fluid level

� High transmission fluid level

� Restricted air flow to the radiator and the auxiliarytransmission oil cooler (if equipped).

A temporary solution to hotter transmission operatingtemperatures may be to let the transmission cool down.If the transmission is operated at higher temperatures ona frequent basis, see “Scheduled Maintenance” in theIndex for the proper transmission maintenance intervals.

yellowblue

2-88

LOW COOLANT

This message is displayedwhen the cooling system islow on coolant.

The engine may overheat. See “Engine Coolant” in theIndex and have your vehicle serviced as soon as you can.

CHECK COOLANT TEMP

This message is displayedwhen the cooling systemtemperature gets hot.

Check the coolant temperature gage and the coolantlevel. See “Engine Coolant” and “Engine CoolantTemperature Gage” in the Index. See “EngineOverheating” in the Index for further information.

ENGINE OVERHEATED

This message is displayedwhen the cooling systemtemperature gets too hot.

This message will be displayed after the air conditioningsystem has automatically turned off for the enginecoolant protection mode. See “Engine Overheating” inthe Index for further information.

REDUCED ENGINE POWER (V8 Engines Only)

This message is displayedwhen the cooling systemtemperature gets too hot and the engine furtherenters the engine coolantprotection mode.

See “Engine Overheating” in the Index for further information.

yellowblue

2-89

CHECK ENG OIL PRESSURE

This message is displayedwhen the engine oil pressureis low.

See “Oil Pressure Gage” in the Index for more information.

CHECK ENG OIL LEVEL

This message is displayedwhen the engine oil level is low.

Once oil is added, it may need time to drain and settle inthe engine before this message will turn off. It is best tolet the engine cool down (if it is hot) or warm up (if it iscold) and cycle the ignition to be sure this message turnsoff. Refer to the dipstick for the correct level.

See “Engine Oil” in the Index on how to check the oillevel and for what type of oil to add.

CHANGE ENGINE OIL

This message is displayedwhen the engine oil needs tobe changed. The message isonly displayed for 15 seconds at the start ofeach ignition cycle.

When you change the engine oil, be sure to reset theEngine Oil Life Monitor. See “Engine Oil, When toChange” in the Index.

SECURITY

This message is displayed when the content theft-deterrentsystem has been activatedand also monitors thePasslock� System.

If the security message is displayed continuously whiledriving and stays on, there may be a problem with thePasslock System. Your vehicle will not be protected byPasslock, and you should see your GM dealer.

yellowblue

2-90

SERVICE 4WD (If Equipped)

If the SERVICE 4WDmessage comes on, theremay be a problem with theautomatic transfer case andservice is required.

Malfunctions can be indicated by the system before anyproblem is apparent, which may prevent serious damageto the vehicle. This system is also designed to assistyour service technician in correctly diagnosing a malfunction.

LOW WASHER FLUID

This message is displayedwhen the vehicle is low onwindshield washer fluid.The message is onlydisplayed for 15 seconds at the start of each ignition cycle.

For more information see, “Windshield Washer Fluid” inthe Index.

CARGO LAMP ON

This message is displayedwhen the cargo lamp isturned on and the ignitionkey is turned to RUN.

LOW FUEL

This message is displayedwhen your vehicle is low on fuel.

Refer to the fuel gage for a better indication of theamount of fuel remaining in the fuel tank.

3-

yellowblue

3-1

Section 3 Comfort Controls and Audio Systems

In this section, you’ll find out how to operate the comfort control and audio systems offered with your vehicle. Be sure to read about the particular systems supplied with your vehicle.

3-2 Comfort Controls3-2 Standard Comfort Controls3-3 Heater and Air Conditioning Comfort

Controls (If Equipped)3-5 Air Conditioning3-6 Heating3-6 Defogging and Defrosting3-6 Rear Window Defogger (If Equipped)3-7 Ventilation System3-8 Audio Systems3-8 Setting the Clock for Systems with

SET Button3-8 Setting the Clock for Systems with HR and

MN Buttons3-9 AM-FM Stereo

3-11 AM-FM Stereo with Cassette Tape Player (If Equipped)

3-14 AM-FM Stereo with Cassette Tape Player andAutomatic Tone Control (If Equipped)

3-18 AM-FM Stereo with Compact Disc Player andAutomatic Tone Control (If Equipped)

3-22 Remote Compact Disc Player (If Equipped)3-24 Theft-Deterrent Feature (If Equipped)3-26 Understanding Radio Reception3-26 Tips About Your Audio System3-27 Care of Your Cassette Tape Player3-28 Care of Your Compact Discs3-28 Care of Your Compact Disc Player3-28 Fixed Mast Antenna

yellowblue

3-2

Comfort ControlsStandard Comfort Controls

Fan Knob

The knob on the left side of the control panel adjusts thefan speed. To increase airflow, turn the knob clockwise.To decrease airflow, turn it counterclockwise. To turnthe fan off, turn the knob to OFF.

Temperature Knob

The middle knob on the control panel lets you select thetemperature of the air flowing into the passenger area.Turn the knob clockwise toward the red area for warmerair. Turn the knob counterclockwise toward the blue areafor cooler air.

Mode Knob

The right knob on the control panel allows you tochoose the direction of air delivery.

VENT: This setting directs the air through theinstrument panel outlets.

BI-LEVEL: Air is delivered through the heaterfloor outlets as well as the instrument panel outlets. The air flow can be divided between VENT andHEATER depending upon where the knob is placedbetween the settings.

HEATER: This setting directs most of thewarmed air through the heater floor outlets, and the restof the air is divided between the windshield defrosteroutlets and the side window defroster outlets.

BLEND: Airflow is delivered through the heaterfloor outlets, the windshield defroster outlets and theside window defroster outlets. The air flow can bedivided between HEATER and DEFROST dependingupon where the knob is placed between the settings.

DEFROST: This setting directs most air throughthe windshield defroster outlets, side window defrosteroutlets and some through the heater outlets.

yellowblue

3-3

Heater and Air Conditioning ComfortControls (If Equipped)

Fan Knob

The knob on the left side of the control panel adjusts thefan speed. To increase airflow, turn the knob clockwise.To decrease airflow, turn it counterclockwise. To turnthe fan off, turn the knob to OFF.

Temperature Knob

The middle knob on the control panel lets you select thetemperature of the air flowing into the passenger area.Turn the knob clockwise toward the red area for warmerair. Turn the knob counterclockwise toward the blue areafor cooler air.

Mode Knob

The right knob on the control panel allows you tochoose the direction of air delivery.

PANEL: This setting directs the air through theinstrument panel outlets and the center floor console (if equipped).

BI-LEVEL: Air is delivered through theinstrument panel outlets and center floor console outlets(if equipped) as well as the heater floor outlets. The airflow can be divided between PANEL and HEATERdepending upon where the knob is placed between thesettings. Pressing the A/C button while in this modecauses cooler air to come out of the instrument paneloutlets and center floor console outlets (if equipped) andwarmer air to come out of the heater floor outlets.

HEATER: This setting directs most of thewarmed air through the heater floor outlets and centerfloor console outlets (if equipped), as well as some airthrough the windshield defroster outlets and sidewindow defroster outlets. If air from the center floorconsole outlets is not desired, turn the vents off at the console.

yellowblue

3-4

BLEND: Airflow is delivered through the heaterfloor outlets, center floor console outlets (if equipped),the windshield defroster outlets and the side windowdefroster outlets. The air flow can be divided betweenHEATER and DEFROST depending upon where the knob is placed between the settings. The airconditioning compressor may run to dehumidify the air to prevent window fogging.

DEFROST: This setting directs most of the airthrough the windshield defroster outlets, side windowdefroster outlets and some air through the heater outletsand center floor console outlets (if equipped). If air fromthe center floor console outlets is not desired or moredefroster performance is desired, turn the vents off at theconsole. When in the DEFROST mode, the airconditioning compressor may run to dehumidify the airto prevent window fogging.

OUTSIDE AIR: Press this button to direct thesystem to use outside air.

Pressing the OUTSIDE AIR button will cancel theRECIRCULATION button.

RECIRCULATION: Press this button to limitthe amount of fresh outside air entering your vehicle.This is helpful when you are trying to limit odorsentering your vehicle, because the air inside the vehicleis being recirculated. Pressing RECIRCULATION willrecirculate air continuously.

RECIRCULATION is used when the fan control is OFFto limit odors, outside air and dust from entering yourvehicle. All button lights will go off. The last settingselected will activate when the blower is turned back on.

Pressing the RECIRCULATION button will cancel theOUTSIDE AIR button.

In the BLEND mode, outside air is forced to reducewindow fogging. If the RECIRCULATION button ispressed, the LED indicator will flash three timesindicating that forced outside air is activated.

The auto recirculation feature will activate when:

� the air conditioning system is activated,

� the OUTSIDE AIR button is on, and

� the vehicle load is high due to city traffic, extendedidling or hot weather.

yellowblue

3-5

The system will automatically switch to the recirculationmode to lower the system load and improve interiorcomfort. The OUTSIDE AIR and RECIRCULATIONbutton LEDs will not change. The system will return tothe OUTSIDE AIR function when the system load is reduced.

A/C: Press this button to turn the air conditioningon and off. The system will cool and dehumidify the airinside the vehicle when the A/C light is on.

Air conditioning will be automatically disabled whenthe outside temperature drops below a level at which airconditioning is ineffective.

Air ConditioningOn hot days, open the windows long enough to let hotair inside escape. This reduces the time it takes for yourvehicle to cool down. Then keep your windows closedfor the air conditioner to work its best.

The RECIRCULATION button allows the air insideyour vehicle to be recirculated. This setting helps tomaximize your air conditioner’s performance and yourvehicle’s fuel economy. This setting also cools air thefastest and can be used to keep unwanted odors and/or dust from entering the vehicle. When using the air conditioner, turn off the

RECIRCULATION button after the vehicle reaches acomfortable interior temperature. When the right knobon the control panel is between HEATER andDEFROST, the recirculation feature will not function toreduce window fogging.

The A/C button, below the mode knob, allows the aircoming into your vehicle to be cooled. This setting isuseful for normal cooling on hot days. When you useA/C with the RECIRCULATION button pushed in, turnoff recirculation as soon as the vehicle reaches acomfortable interior temperature.

Maximum air conditioning performance is obtained bypressing the A/C button, the RECIRCULATION buttonand turning the temperature knob fully counterclockwiseto the blue area. This setting also cools air the fastest.After the vehicle’s interior reaches a comfortabletemperature, press the OUTSIDE AIR button to placethe air conditioning system in the normal mode.

Passenger Compartment Air Filter (If Equipped)

If your vehicle has air conditioning, it is equipped with apassenger compartment air filter, which filters outsideair entering the vehicle. For information on replacing thefilter see “Passenger Compartment Air Filter” in the Index.

yellowblue

3-6

HeatingThe heater works best if you keep your windows closedwhile using it. On cold days, use the HEATER orVENT/HEAT setting with the temperature knob in thered area.

On cold days, approximately 32�F (-0�C) or lower, ifyour vehicle is equipped with an automatic transmission,you may experience differences in how the transmissionshifts until the engine is warm. This featureautomatically reduces the time it takes for the engine toreach normal operating temperature and shortens thetime it takes the heater to reach full output.

If you use the engine coolant heater before starting yourengine in cold weather, 20�F (-8�C) or lower, theheating system will produce warmer air faster to heat thepassenger compartment.

The use of an engine coolant heater also reduces thetime it takes for the engine to reach normal operatingtemperature. For more information, see “Engine CoolantHeater” in the Index.

Defogging and DefrostingOn cool, humid days, use DEFOG to keep thewindshield and side windows clear. Use DEFROST toremove fog or ice from the windshield in extremelyhumid or cold conditions. Use DEFROST with thetemperature knob toward the red area and the fan controlturned all the way to the right.

Rear Window Defogger (If Equipped)If you see lines running across the rear window, youhave a rear window defogger. The lines warm the glass.

To turn on the rear windowdefogger, press this buttonnext to the fan control knob.

The rear window defoggerwill only work if theignition is in RUN. For bestresults, clear the window ofas much snow or ice aspossible first.

The defogger will shut itself off after several minutes. If you need additional warming time, press the buttonagain. You can turn the defogger off at any time bypressing the button.

yellowblue

3-7

If your vehicle is equipped with heated outside mirrors,the rear window defogger button will also activate theheated outside mirrors.

Do not attach a temporary vehicle license, tape or decalsacross the defogger grid on the rear window.

NOTICE:

Don’t use a razor blade or something else sharpon the inside of the rear window. If you do, youcould cut or damage the warming grid, and therepairs wouldn’t be covered by your warranty.

Ventilation SystemFor mild outside temperatures when little heating orcooling is needed, use VENT to direct outside airthrough your vehicle. Air will flow through theinstrument panel outlets.

Your vehicle’s ventilation system supplies outside air to the inside of your vehicle when it is moving. With the side windows closed, air will flow into the front airinlet grilles, through the vehicle, and out the air exhaust valves.

Outside air will also enter the vehicle when the heater orthe air conditioning fan is running, unless you have theRECIRCULATION button pushed in. For moreinformation on the RECIRCULATION button, see “Air Conditioning” earlier in this section.

Your vehicle has air outlets in the center and on the sides of yourinstrument panel.

You can turn the outlets from side-to-side or up anddown to direct the flow of air. The left driver andpassenger outlets on vehicles equipped with airconditioning have shut off knobs. Turn the knob to theleft to shut off air flow, to the right to allow air flow.When you close an outlet, it will increase the flow of aircoming out of any outlets that are open. The centeroutlet does not completely shut off airflow.

yellowblue

3-8

Ventilation Tips

� Keep the hood and front air inlet free of ice, snow orany other obstruction (such as leaves). The heaterand defroster will work far better, reducing thechance of fogging the inside of your windows.

� When you enter a vehicle in cold weather, turn theblower fan all the way to the right for a few momentsbefore driving. This helps clear the intake ducts ofsnow and moisture, and reduces the chance offogging the inside of your windows.

� Keep the air path under the front seats clear ofobjects. This helps air to circulate throughout your vehicle.

� The use of hood air deflectors may adversely affect the performance of the heating and airconditioning system.

Audio SystemsYour audio system has been designed to operate easilyand give years of listening pleasure. You will get themost enjoyment out of it if you acquaint yourself with itfirst. Find out what your audio system can do and howto operate all its controls, to be sure you’re getting themost out of the advanced engineering that went into it.

Setting the Clock for Systems with SET ButtonPress SET. Within five seconds, press and hold theSEEK right arrow until the correct minute appears onthe display. Press and hold the SEEK left arrow until thecorrect hour appears on the display.

Setting the Clock for Systems with HR andMN ButtonsPress and hold HR until the correct hour appears on thedisplay. Press and hold MN until the correct minuteappears on the display. To display the clock with theignition off, press RECALL or HR/MN and the timewill be displayed for a few seconds. There is an initialtwo-second delay before the clock goes into the time-set mode.

yellowblue

3-9

AM-FM Stereo

Playing the Radio

VOLUME: This knob turns the system on and off and controls the volume. To increase volume and turn the radio on, turn the knob clockwise. Turn itcounterclockwise to decrease volume and turn the radio off.

RECALL: Display the time with the ignition off bypressing the recall knob. When the radio is playing,press this knob to recall the station frequency.

Finding a Station

AM -FM: Press the lower knob to switch between AMand FM. The display shows your selection.

TUNE: Turn the lower knob to tune in radio stations.

SEEK: Press the right arrow to tune to the next higherstation and the left arrow to tune to the next lowerstation and stay there.

SCAN: Select either AM, FM1 or FM2 mode and pressboth SEEK buttons to listen to a few seconds of eachradio station. SCAN will light up on the display. Theradio will automatically SCAN to the next higherstation, play that station for a few seconds, then SCANto the next higher station. Press VOLUME or bothSEEK buttons to stop scanning.

yellowblue

3-10

PUSHBUTTONS: The four numbered pushbuttons letyou return to your favorite stations. You can set up to 14 stations (seven AM and seven FM). Just:

1. Turn the radio on.

2. Press AM-FM to select the band.

3. Tune in the desired station.

4. Press SET. (SET will appear on the display.)

5. Press one of the four pushbuttons within fiveseconds. Whenever you press that numbered button,the station you set will return.

6. Repeat the steps for each pushbutton.

In addition to the four stations already set, up to threemore stations may be preset on each band by pressingtwo adjoining buttons at the same time. Just:

1. Tune in the desired station.

2. Press SET. (SET will appear on the display.)

3. Press two adjoining buttons at the same time, withinfive seconds. Whenever you press the same twobuttons, the station you set will return.

4. Repeat the steps for each pair of pushbuttons.

Setting the Tone

BASS: Slide this lever up or down to increase ordecrease bass.

TREB: Slide this lever up or down to increase ordecrease treble. If a station is weak or noisy, you maywant to decrease the treble.

Adjusting the Speakers

BAL: Turn the control behind the upper knob to movethe sound to the left or right speakers. The middleposition balances the sound between the speakers.

FADE: Turn the control behind the lower knob to movethe sound to the front or rear speakers. The middleposition balances the sound between the speakers.

yellowblue

3-11

AM-FM Stereo with Cassette Tape Player(If Equipped)

Playing the Radio

VOLUME: This knob turns the system on and off and controls the volume. To increase volume and turn the radio on, turn the knob clockwise. Turn itcounterclockwise to decrease volume and turn the radio off.

RECALL: Display the time with the ignition off bypressing this knob. When the radio is playing, press thisknob to recall the station frequency.

Finding a Station

AM -FM: Press the lower knob to switch between AM,FM1 and FM2.

TUNE: Turn the lower knob to tune in radio stations.

SEEK: Press the right arrow to tune to the next higher station and the left arrow to tune to the nextlower station.

PUSHBUTTONS: The four numbered pushbuttons letyou return to your favorite stations. You can set up to 21 stations (seven AM, seven FM1 and seven FM2). Just:

1. Turn the radio on.

2. Press AM-FM to select the band.

3. Tune in the desired station.

4. Press SET. (SET will appear on the display.)

5. Press one of the four pushbuttons within fiveseconds. Whenever you press that numbered button,the station you set will return.

6. Repeat the steps for each pushbutton.

yellowblue

3-12

In addition to the four stations already set, up to threemore stations may be preset on each band by pressingtwo adjoining buttons at the same time. Just:

1. Tune in the desired station.

2. Press SET. (SET will appear on the display.)

3. Press two adjoining buttons at the same time, withinfive seconds. Whenever you press the same twobuttons, the station you set will return.

4. Repeat the steps for each pair of pushbuttons.

P.SCAN: Select either AM, FM1 or FM2 mode andpress both SEEK buttons to scan through each of yourpreset stations. The system will scan through and playeach preset station stored on your pushbuttons for a fewseconds. Press either SEEK button or RECALL to stopscanning through the preset stations.

Setting the Tone

BASS: Slide this lever up or down to increase ordecrease bass.

TREB: Slide this lever up or down to increase ordecrease treble. If a station is weak or noisy, you maywant to decrease the treble.

Adjusting the Speakers

BAL: Turn the control behind the upper knob to movethe sound to the left or right speakers. The middleposition balances the sound between the speakers.

FADE: Turn the control behind the lower knob to movethe sound to the front or rear speakers. The middleposition balances the sound between the speakers.

yellowblue

3-13

Playing a Cassette Tape

Your tape player is built to work best with tapes that are up to 30 to 45 minutes long on each side. Tapeslonger than that are so thin they may not work well inthis player.

Once the tape is playing, use the knobs for VOLUME,BAL, FADE, BASS and TREB just as you do for the radio.

REV: Press the SEEK left arrow to reverse the cassettetape. Press the SEEK right arrow to stop reversing the tape.

FWD: Press the SEEK right arrow to advance thecassette tape. Press the SEEK left arrow to stopforwarding the tape.

RECALL: Press this knob to switch tape sides.

EJECT: Press this button to remove the tape or stop thetape and play the radio.

CLN: If this message appears on the display, thecassette tape player needs to be cleaned. It will still playtapes, but you should clean it as soon as possible toprevent damage to the tapes and player. See “Care ofYour Cassette Tape Player” in the Index. After you cleanthe player, press and hold EJECT for five seconds toreset the CLN indicator. The radio will display --- toshow the indicator was reset.

CD Adapter Kits

It is possible to use a portable CD player adapter kitwith your cassette tape player after activating the bypassfeature on your tape player.

To activate the bypass feature, use the following steps:

1. Turn the radio on.

2. Insert the adapter into the cassette slot.

3. Within five seconds, press and hold the REV andFWD buttons at the same time for three seconds. The tape symbol on the display will flash, showingthat the cut tape detection feature is no longer active.

This override routine will remain active until EJECT is pressed.

yellowblue

3-14

AM-FM Stereo with Cassette Tape Playerand Automatic Tone Control (If Equipped)

Playing the Radio

PWR-VOL: Press this knob to turn the system on andoff. To increase volume, turn the knob clockwise. Turnit counterclockwise to decrease volume. The knob iscapable of being rotated continuously.

RECALL: Display the time with the ignition off bypressing this button. When the radio is playing, pressthis button to recall the station frequency.

SCV: Your system has a feature calledSpeed-Compensated Volume (SCV). With SCV, youraudio system adjusts automatically to make up for roadand wind noise as you drive. Set the volume at thedesired level. Turn the control ring behind the upperknob clockwise to adjust the SCV. Then, as you drive,SCV automatically increases the volume, as necessary,to overcome noise at any particular speed. The volumelevel should always sound the same to you as you drive.If you don’t want to use SCV, turn the control all theway down. Each notch on the control ring allows formore volume compensation at faster vehicle speeds.

Finding a Station

AM -FM: Press this button to switch between AM, FM1and FM2. The display will show your selection.

TUNE: Press this knob lightly so it extends. Turn it tochoose radio stations. Push the knob back into its storedposition when you’re not using it.

SEEK: Press the right arrow to tune to the next higherstation and the left arrow to tune to the next lowerstation and stay there. The sound will mute while seeking.

yellowblue

3-15

SCAN: Press and hold SEEK for two seconds untilSCAN appears on the display. SCAN allows you tolisten to stations for a few seconds. The receiver willcontinue to scan and momentarily stop at each stationuntil you press the button again. The sound will mutewhile scanning.

PUSHBUTTONS: The six numbered pushbuttons letyou return to your favorite stations. You can set up to 18 stations (six AM, six FM1 and six FM2). Just:

1. Turn the radio on.

2. Press AM-FM to select the band.

3. Tune in the desired station.

4. Press AUTO TONE to select the setting you prefer.

5. Press and hold one of the six pushbuttons. The soundwill mute. When it returns, release the button.Whenever you press that numbered button, thestation you set will return and the tone you selectedwill be automatically selected for that button.

6. Repeat the steps for each pushbutton.

P.SCAN: The preset scan button lets you scan throughyour favorite stations stored on your pushbuttons. Selecteither the AM, FM1 or FM2 mode and then press P. SCAN. It will scan through each station stored onyour pushbuttons and stop for a few seconds beforecontinuing to scan through all of the pushbuttons. PressP. SCAN again or one of the pushbuttons to stopscanning to listen to a specific preset station. P. SCANwill light up on the display while in this mode. If one ofthe stations stored on a pushbutton is too weak for thelocation you are in, the radio display will show thechannel number (P1-P6) for several seconds beforeadvancing to the next preset station.

Setting the Tone

BASS: Press lightly on this knob to release it from itsstored position. Turn the knob clockwise to increase bassand counterclockwise to decrease bass. When the BASScontrol is rotated, the AUTO TONE display will go blank.

TREB: Press lightly on this knob to release it from itsstored position. Turn the knob clockwise to increasetreble and counterclockwise to decrease treble. Whenthe TREB control is rotated, the AUTO TONE displaywill go blank. If a station is weak or noisy, you maywant to decrease the treble.

Push these knobs back into their stored positions whenyou’re not using them.

yellowblue

3-16

AUTO TONE: Press this button to select among the six preset equalization settings and tailor the sound tothe music or voice being heard. Each time you press thebutton, the selection will switch to one of the presetsettings of CLASSIC, NEWS, ROCK, POP, C/W(Country/Western) or JAZZ. To return to the manualmode, press and release this button until the AUTOTONE display goes blank. This will return the toneadjustment to the BASS and TREB controls. If a BASS or TREB control is rotated, the AUTO TONEdisplay will go blank. Use PUSHBUTTONS to programAUTO TONE.

Adjusting the Speakers

BAL: Press lightly on this knob to release it from itsstored position. Turn the control clockwise to adjustsound to the right speakers and counterclockwise toadjust sound to the left speakers. The middle positionbalances the sound between the speakers.

FADE: Press lightly on this knob to release it from itsstored position. Turn the control clockwise to adjust thesound to the front speakers and counterclockwise for therear speakers. The middle position balances the soundbetween the speakers.

Push these knobs back into their stored positions whenyou’re not using them.

Playing a Cassette Tape

Your tape player is built to work best with tapes that areup to 30 to 45 minutes long on each side. Tapes longerthan that are so thin they may not work well in this player.

To load a cassette tape with the ignition off, pressEJECT or RECALL. Then, insert the cassette tape. If the ignition is on but the radio is off, the tape willbegin playing.

Once the tape is playing, use the VOL, AUTO TONE,BAL, FADE, BASS and TREB controls just as you dofor the radio. The tape symbol and a direction arrow willbe on the display whenever a tape is being played.Anytime a tape is inserted, the top side is selected forplay first.

The player automatically senses if the cassette tape ismetal or CrO2 and adjusts for best playback sound.

PREV (1): Press the PREV button or the SEEK leftarrow to search for the previous selection. A minimumthree-second blank gap is required for the player to stopat the beginning of the selection. The tape directionarrow will blink during the SEEK operation.

PROG (2): Press this button to switch from one side ofthe tape to the other.

yellowblue

3-17

NEXT (3): Press the NEXT button or the SEEK rightarrow to search for the next selection. A minimumthree-second blank gap is required for the player to stopat the beginning of the selection. The tape directionarrow will blink during the SEEK operation. The soundwill mute while searching for the next selection.

REV (4): Press this button to rapidly reverse the tape tothe beginning of the cassette or until you press REVagain. The radio will play the last selected station whilereversing the tape. The tape direction arrow will blinkduring the reverse operation.

� (5): Press this button to reduce cassette tape noise.The double-D symbol will appear on the display whilethe player is in this mode.

Dolby Noise Reduction is manufactured under a licensefrom Dolby Laboratories Licensing Corporation. Dolbyand the double-D symbol are trademarks of DolbyLaboratories Licensing Corporation.

FWD (6): Press this button to rapidly forward the tapeto the end of the cassette or until you press FWD again.The radio will play the last selected station whileforwarding the tape. The tape direction arrow will blinkduring the forward operation.

AM -FM: Press this button to switch from a tape to the radio.

TAPE AUX: Press this button to return to the tapeplayer when playing the radio. The lighted arrow willappear and show the direction of play when a tape is inthe active mode.

EJECT: Press this button to remove the tape. The radio will now play. EJECT can be used with eitherthe ignition or radio off. To load a cassette tape with theignition or radio off, press EJECT before loading the cassette.

CLN: If this message appears on the display, thecassette tape player needs to be cleaned. It will still playtapes, but you should clean it as soon as possible toprevent damage to the tapes and player. See “Care ofYour Cassette Tape Player” in the Index. After you cleanthe player, press and hold EJECT for five seconds toreset the CLN indicator. The radio will display --- toshow the indicator was reset.

yellowblue

3-18

CD Adapter Kits

It is possible to use a portable CD player adapter kitwith your cassette tape player after activating the bypassfeature on your tape player.

To activate the bypass feature, use the following steps:

1. Turn the ignition to RUN or ACCESSORY.

2. Turn the radio off.

3. Press and hold the TAPE AUX button for fiveseconds. The tape symbol on the display will flashfor two seconds, indicating the feature is active.

4. Insert the adapter into the cassette slot. It will powerup the radio and begin playing.

This override routine will remain active until EJECT is pressed.

AM-FM Stereo with Compact Disc Playerand Automatic Tone Control (If Equipped)

Playing the Radio

PWR-VOL: Press this knob to turn the system on andoff. To increase volume, turn this knob clockwise. Turnit counterclockwise to decrease volume. The knob iscapable of rotating continuously.

RECALL: Display the time with the ignition off bypressing this button. When the radio is playing, pressthis button to recall the station frequency.

yellowblue

3-19

SCV: Your system has a feature calledSpeed-Compensated Volume (SCV). With SCV, youraudio system adjusts automatically to make up for roadand wind noise as you drive. Set the volume at thedesired level. Turn the control ring behind the upperknob clockwise to adjust the SCV. Then, as you drive,SCV automatically increases the volume, as necessary,to overcome noise at any particular speed. The volumelevel should always sound the same to you as you drive.If you don’t want to use SCV, turn the control all theway down. Each notch on the control ring allows formore volume compensation at faster vehicle speeds.

Finding a Station

AM -FM: Press this button to switch between AM, FM1and FM2. The display will show your selection.

TUNE: Press this knob lightly so it extends. Turn it tochoose radio stations. Push the knob back into its storedposition when you’re not using it.

SEEK: Press the right arrow to tune to the next higherstation and the left arrow to tune to the next lowerstation and stay there. The sound will mute while seeking.

SCAN: Press and hold SEEK for two seconds untilSCAN appears on the display. SCAN allows you tolisten to stations for a few seconds. The receiver willcontinue to scan and momentarily stop at each stationuntil you press the button again. The sound will mutewhile scanning.

PUSHBUTTONS: The six numbered pushbuttons letyou return to your favorite stations. You can set up to 18 stations (six AM, six FM1 and six FM2). Just:

1. Turn the radio on.

2. Press AM-FM to select the band.

3. Tune in the desired station.

4. Press AUTO TONE to select the setting you prefer.

5. Press and hold one of the six pushbuttons. The soundwill mute. When it returns, release the button.Whenever you press that numbered button, thestation you set will return and the tone you selectedwill be automatically selected for that button.

6. Repeat the steps for each pushbutton.

yellowblue

3-20

P.SCAN: The preset scan button lets you scan throughyour favorite stations stored on your pushbuttons. Select either the AM, FM1 or FM2 mode and then pressP.SCAN. It will scan through each station stored on your pushbuttons and stop for a few seconds beforecontinuing to scan through all of the pushbuttons. Press P.SCAN again or one of the pushbuttons to stopscanning to listen to a specific stored station. P.SCANwill light up on the display while in this mode. If one ofthe stations stored on a pushbutton is too weak for thelocation you are in, the radio display will show thechannel number (P1-P6) for several seconds beforeadvancing to the next preset station.

Setting the Tone

BASS: Press lightly on this knob to release it from itsstored position. Turn the knob clockwise to increase bassand counterclockwise to decrease bass. When the BASScontrol is rotated, the AUTO TONE display will go blank.

TREB: Press lightly on this knob to release it from itsstored position. Turn the knob clockwise to increasetreble and counterclockwise to decrease treble. Whenthe TREB control is rotated, the AUTO TONE displaywill go blank. If a station is weak or noisy, you maywant to decrease the treble.

Push these knobs back into their stored positions whenyou’re not using them.

AUTO TONE: Press this button to select among the six preset equalization settings and tailor the sound tothe music or voice being heard. Each time you press thebutton, the selection will switch to one of the presetsettings of CLASSIC, NEWS, ROCK, POP, C/W(Country/Western) or JAZZ. To return to the manualmode, press and release this button until the AUTOTONE display goes blank. This will return the toneadjustment to the BASS and TREB controls. If a BASS or TREB control is rotated, the AUTO TONEdisplay will go blank. Use PUSHBUTTONS to programAUTO TONE.

Adjusting the Speakers

BAL: Press lightly on this knob to release it from itsstored position. Turn the control clockwise to adjustsound to the right speakers and counterclockwise toadjust sound to the left speakers. The middle positionbalances the sound between the speakers.

FADE: Press lightly on this knob to release it from itsstored position. Turn the control clockwise to adjust thesound to the front speakers and counterclockwise for therear speakers. The middle position balances the soundbetween the speakers.

Push these knobs back into their stored positions whenyou’re not using them.

yellowblue

3-21

Playing a Compact Disc

PWR: Press this knob to turn the system on. (Please note that you can also turn the system on whenyou insert a compact disc into the player with theignition on.)

Insert a disc partway into the slot, label side up. Theplayer will pull it in. Wait a few seconds and the discshould play. CD and a CD symbol will also appear onthe display. Anytime you are playing a CD, the lettersCD will be next to the CD symbol.

If the disc comes back out and ERR appears on thedisplay, it could be that:

� You are driving on a very rough road. (The discshould play when the road gets smoother.)

� The disc is upside down.

� It is dirty, scratched or wet.

� It is very humid. (If so, wait about an hour and try again.)

� The disc player is very hot.

Press RECALL to make ERR go off the display.

PREV (1): Press PREV or the SEEK left arrow tosearch for the previous selection. If you hold this buttonor press it more than once, the disc will advance further.Sound is muted in this mode.

RDM (2): Press this button to play the tracks on the discin random order. While in the RDM mode, RANDOMappears on the display. Press RDM again to return tonormal play.

NEXT (3): Press NEXT or the SEEK right arrow tosearch for the next selection. If you hold this button orpress it more than once, the disc will advance further.The next track number will appear on the display. Soundis muted in this mode.

REV (4): Press and hold REV to return rapidly to afavorite passage. You will hear the disc selection play athigh speed while you press the REV button. This allowsyou to listen and find out when the disc is at the desiredselection. Release REV to resume playing.

FWD (6): Press and hold this button to advance rapidlywithin a track. You will hear the disc selection play athigh speed while you press the FWD button. This allowsyou to listen and find out when the disc is at the desiredselection. Release FWD to resume playing.

yellowblue

3-22

RECALL: Press this button to see what track is playing.Press it again within five seconds to see how long theCD has been playing that track. Elapsed time isdisplayed in minutes and seconds. The track numberwill also appear when a new track begins to play. PressRECALL again to return to the time display.

AM -FM: While in the CD mode, press this button tostop playing the CD and play the radio. The CD symbolwill still display but the word CD will be replaced witheither AM, FM1 or FM2. (If the radio is turned off, thedisc stays in the player and will resume playing at thepoint where it stopped.)

CD AUX: To switch between the player and the radiowhen a disc is playing, press the AM-FM button. Toreturn to the player, press CD AUX. When a disc isplaying, the letters CD and the CD symbol will appearon the display. (If the radio is turned off, the disc staysin the player and will resume playing at the point whereit stopped.)

EJECT: Press this button to eject the disc from theplayer and play the radio. When the same or a new discis inserted, the disc will start playing on track one. If acompact disc is left sitting in the opening for more thana few seconds, the player will pull the CD back in. Theradio will continue playing. When the ignition is off,press this button to load a CD.

Remote Compact Disc Player (If Equipped)

If you have this option, you can play one compact disc(CD) at a time.

To load a CD into the player, hold the disc with the label side up and insert it carefully into the player (approximately halfway). The disc will automatically be pulled into the player. If the radio is off and the ignition is on when a CD is inserted, the radio will turn on and begin playing the CD. It is possible to load and unload CDs with the ignition off. To loada disc with the ignition off, press the EJECT button on the remote player and then insert the disc. To remove the disc, press the EJECT button and remove the disc from the player.

A disc that has been ejected but is still sitting in theremote CD player will be pulled back into the playerafter approximately 30 seconds. This protects the discand player from damage. The disc will not start playing.To remove the disc, press the EJECT button and removethe disc from the player.

yellowblue

3-23

All of the compact disc functions are controlled by the radio buttons except for EJECT. When a disc is in the player, a CD symbol will appear on the display. When a disc is playing, theletters CD will appear next to the CD symbol in the bottom left corner. The track number will also be displayed.

If the disc comes back out and ERR appears on thedisplay, it could be that:� The disc is upside down.� It is dirty, scratched or wet.

� There’s too much moisture in the air. (Wait about anhour and try again.)

� You are driving on a very rough road.Please contact your dealership if any error recurs orcannot be corrected.PREV (1): Press this button to go back to the start of thecurrent track if more than eight seconds have played.Press PREV again to go to the previous track on the disc.NEXT (3): Press this button to advance to the next trackon the disc.

REV (4): Press and hold this button to quickly reversewithin a track. As the CD reverses, elapsed time will bedisplayed to help you find the correct passage.FWD (6): Press and hold this button to quickly advancewithin a track. As the CD advances, elapsed time will bedisplayed to help you find the correct passage.

SEEK: Press the left arrow while playing a CD to goback to the start of the current track. It will go back tothe current track if more than eight seconds have played.Press the left arrow again to go to previous tracks. Pressthe right arrow to go to the next higher track on the disc.

RANDOM: Press P.SCAN to enter the random playmode. RANDOM will appear on the display. While inthis mode, the tracks on the disc will be played inrandom order. If you press SEEK, PREV or NEXTwhile in the random mode, the previous or next trackwill be scanned randomly. Press P.SCAN again to turnoff RANDOM and return to normal operation.

RECALL: Press this button to see what track iscurrently playing. Press RECALL again within fiveseconds to see how long the track has been playing.When a new track starts to play, the track number willalso appear. Press RECALL a third time and the time ofday will be displayed.

TAPE AUX: With a disc loaded in the player and theradio playing, press this button once to play the compactdisc. To return to playing the radio, press AM-FM. Ifboth a cassette tape and CD are loaded, press TAPEAUX to switch between the tape and compact disc.

EJECT: Press this button on the remote player to eject acompact disc.

yellowblue

3-24

Theft-Deterrent Feature (If Equipped)THEFTLOCK� is designed to discourage theft of yourradio. It works by using a secret code to disable all radiofunctions whenever battery power is removed.

The THEFTLOCK feature for the radio may be used orignored. If ignored, the system plays normally and theradio is not protected by the feature. If THEFTLOCK isactivated, your radio will not operate if stolen.

When THEFTLOCK is activated, the radio will displayLOC to indicate a locked condition anytime batterypower has been interrupted. If your battery loses powerfor any reason, you must unlock the radio with the secretcode before it will operate.

Activating the Theft-Deterrent Feature

The instructions which follow explain how to enter yoursecret code to activate the THEFTLOCK system. It isrecommended that you read through all nine stepsbefore starting the procedure.

NOTE: If you allow more than 15 seconds to elapsebetween any steps, the radio automatically reverts totime and you must start the procedure over at Step 4.

1. Write down any three or four-digit number from 000 to 1999 and keep it in a safe place separate fromthe vehicle.

2. Turn the ignition to ACCESSORY or RUN.

3. Turn the radio off.

4. Press the 1 and 4 buttons together. Hold them downuntil --- shows on the display. Next you will use thesecret code number which you have written down.

5. Press MN and 000 will appear on the display.

6. Press MN again to make the last two digits agreewith your code.

7. Press HR to make the first one or two digits agreewith your code.

8. Press AM-FM after you have confirmed that thecode matches the secret code you have written down.The display will show REP to let you know that youneed to repeat Steps 5 through 7 to confirm yoursecret code.

9. Press AM-FM and this time the display will showSEC to let you know that your radio is secure. TheLED indicator by the volume control will beginflashing when the ignition is turned off.

yellowblue

3-25

Unlocking the Theft-Deterrent Feature After aPower Loss

Enter your secret code as follows; pause no more than15 seconds between steps:

1. Turn the ignition on. LOC will appear on the display.

2. Press MN and 000 will appear on the display.

3. Press MN again to make the last two digits agreewith your code.

4. Press HR to make the first one or two digits agreewith your code.

5. Press AM-FM after you have confirmed that thecode matches the secret code you have written down.The display will show SEC, indicating the radio isnow operable and secure.

If you enter the wrong code eight times, INOP willappear on the display. You will have to wait an hourwith the ignition on before you can try again. When youtry again, you will only have three chances to enter thecorrect code before INOP appears.

If you lose or forget your code, contact your dealer.

Disabling the Theft-Deterrent FeatureEnter your secret code as follows; pause no more than15 seconds between steps:

1. Turn the ignition to ACCESSORY or RUN.

2. Turn the radio off.

3. Press the 1 and 4 buttons together. Hold them downuntil SEC shows on the display.

4. Press MN and 000 will appear on the display.5. Press MN again to make the last two digits agree

with your code.6. Press HR to make the first one or two digits agree

with your code.7. Press AM-FM after you have confirmed that the

code matches the secret code you have written down.The display will show ---, indicating that the radio isno longer secured.

If the code entered is incorrect, SEC will appear on thedisplay. The radio will remain secured until the correctcode is entered.

When battery power is removed and later applied to asecured radio, the radio won’t turn on and LOC willappear on the display.

To unlock a secured radio, see “Unlocking theTheft-Deterrent Feature After a Power Loss” earlier inthis section.

yellowblue

3-26

Understanding Radio Reception

AM

The range for most AM stations is greater than for FM,especially at night. The longer range, however, cancause stations to interfere with each other. AM can pickup noise from things like storms and power lines. Tryreducing the treble to reduce this noise if you ever get it.

FM Stereo

FM stereo will give you the best sound, but FM signalswill reach only about 10 to 40 miles (16 to 65 km). Tallbuildings or hills can interfere with FM signals, causingthe sound to come and go.

Tips About Your Audio SystemHearing damage from loud noise is almost undetectableuntil it is too late. Your hearing can adapt to highervolumes of sound. Sound that seems normal can be loudand harmful to your hearing. Take precautions byadjusting the volume control on your radio to a safesound level before your hearing adapts to it.

To help avoid hearing loss or damage:

� Adjust the volume control to the lowest setting.

� Increase volume slowly until you hear comfortablyand clearly.

NOTICE:

Before you add any sound equipment to yourvehicle -- like a tape player, CB radio, mobiletelephone or two-way radio -- be sure you canadd what you want. If you can, it’s veryimportant to do it properly. Added soundequipment may interfere with the operation ofyour vehicle’s engine, Delco Electronics radio orother systems, and even damage them. Yourvehicle’s systems may interfere with theoperation of sound equipment that has beenadded improperly.So, before adding sound equipment, check withyour dealer and be sure to check Federal rulescovering mobile radio and telephone units.

yellowblue

3-27

Care of Your Cassette Tape PlayerA tape player that is not cleaned regularly can causereduced sound quality, ruined cassettes or a damagedmechanism. Cassette tapes should be stored in theircases away from contaminants, direct sunlight andextreme heat. If they aren’t, they may not operateproperly or may cause failure of the tape player.

Your tape player should be cleaned regularly after every50 hours of use. Your radio may display CLN to indicatethat you have used your tape player for 50 hours withoutresetting the tape clean timer. If this message appears onthe display, your cassette tape player needs to becleaned. It will still play tapes, but you should clean it assoon as possible to prevent damage to your tapes andplayer. If you notice a reduction in sound quality, try aknown good cassette to see if it is the tape or the tapeplayer at fault. If this other cassette has no improvementin sound quality, clean the tape player.

The recommended cleaning method for your cassettetape player is the use of a scrubbing action,non-abrasive cleaning cassette with pads which scrubthe tape head as the hubs of the cleaner cassette turn.The recommended cleaning cassette is available throughyour dealership (GM Part No. 12344789).

When using a scrubbing action, non-abrasive cleaningcassette, it is normal for the cassette to eject becauseyour unit is equipped with a cut tape detection featureand a cleaning cassette may appear as a broken tape. To prevent the cleaning cassette from being ejected, usethe following steps.

If your vehicle is equipped with the AM-FM Stereo withCassette Tape Player:

1. Turn the ignition to RUN or ACCESSORY.

2. Turn the radio on.

3. Insert the scrubbing action cleaning cassette.

4. Within five seconds, press and hold the REV andFWD buttons at the same time for three seconds. The tape symbol on the display will flash, showingthat the cut tape detection feature is no longer active.

5. Eject the cleaning cassette after the manufacturer’srecommended cleaning time.

yellowblue

3-28

If your vehicle is equipped with the AM-FM Stereo withCassette Tape Player and Automatic Tone Control:

1. Turn the ignition to RUN or ACCESSORY.

2. Turn the radio off.

3. Press and hold the TAPE AUX button for fiveseconds. The tape symbol on the display will flashfor two seconds.

4. Insert the scrubbing action cleaning cassette.

5. Eject the cleaning cassette after the manufacturer’srecommended cleaning time.

When the cleaning cassette has been ejected, the cut tapedetection feature is active again.

You may also choose a non-scrubbing action, wet-typecleaner which uses a cassette with a fabric belt to cleanthe tape head. This type of cleaning cassette will noteject on its own. A non-scrubbing action cleaner maynot clean as thoroughly as the scrubbing type cleaner.The use of a non-scrubbing action, dry-type cleaningcassette is not recommended.

After you clean the player, press and hold EJECT forfive seconds to reset the CLN indicator. The radio willdisplay --- to show the indicator was reset.

Cassettes are subject to wear and the sound quality may degrade over time. Always make sure the cassette tape is in good condition before you have your tape player serviced.

Care of Your Compact DiscsHandle discs carefully. Store them in their original casesor other protective cases and away from direct sunlightand dust. If the surface of a disc is soiled, dampen aclean, soft cloth in a mild, neutral detergent solution andclean it, wiping from the center to the edge.

Be sure never to touch the signal surface when handlingdiscs. Pick up discs by grasping the outer edges or theedge of the hole and the outer edge.

Care of Your Compact Disc PlayerThe use of CD lens cleaner discs is not advised, due tothe risk of contaminating the lens of the CD optics withlubricants internal to the CD mechanism.

Fixed Mast AntennaThe fixed mast antenna can withstand most car washes without being damaged. If the mast should ever become slightly bent, you can straighten it out by hand. If the mast is badly bent, as it might be by vandals, you should replace it.

Check every once in a while to be sure the mast is stilltightened to the cowl.

4-

yellowblue

4-1

Section 4 Your Driving and the Road

Here you’ll find information about driving on different kinds of roads and in varying weather conditions. We’ve alsoincluded many other useful tips on driving.

4-2 Defensive Driving4-3 Drunken Driving4-6 Control of a Vehicle4-6 Braking4-9 Steering4-11 Off-Road Recovery4-11 Passing4-13 Loss of Control4-14 Off-Road Driving with Your

Four-Wheel-Drive Vehicle4-31 Driving at Night4-33 Driving in Rain and on Wet Roads

4-37 City Driving4-38 Freeway Driving4-39 Before Leaving on a Long Trip4-40 Highway Hypnosis4-40 Hill and Mountain Roads4-42 Winter Driving4-46 Recreational Vehicle Towing4-48 Loading Your Vehicle4-54 Camper Wiring Harness (If Equipped)4-55 Pickup Conversion to Chassis Cab4-55 Towing a Trailer

yellowblue

4-2

Defensive DrivingThe best advice anyone can give about driving is: Drive defensively.

Please start with a very important safety device in yourvehicle: Buckle up. (See “Safety Belts” in the Index.)

Defensive driving really means “be ready for anything.”On city streets, rural roads or freeways, it means“always expect the unexpected.”

Assume that pedestrians or other drivers are going to becareless and make mistakes. Anticipate what they mightdo. Be ready for their mistakes.

Rear-end collisions are about the most preventable ofaccidents. Yet they are common. Allow enoughfollowing distance. It’s the best defensive drivingmaneuver, in both city and rural driving. You neverknow when the vehicle in front of you is going to brakeor turn suddenly.

Defensive driving requires that a driver concentrate onthe driving task. Anything that distracts from the driving task -- such as concentrating on a cellulartelephone call, reading, or reaching for something on thefloor -- makes proper defensive driving more difficultand can even cause a collision, with resulting injury.Ask a passenger to help do things like this, or pull off the road in a safe place to do them yourself. These simple defensive driving techniques could saveyour life.

yellowblue

4-3

Drunken DrivingDeath and injury associated with drinking and driving isa national tragedy. It’s the number one contributor to the highway death toll, claiming thousands of victimsevery year.

Alcohol affects four things that anyone needs to drive a vehicle:

� Judgment

� Muscular Coordination

� Vision

� Attentiveness.

Police records show that almost half of all motorvehicle-related deaths involve alcohol. In most cases,these deaths are the result of someone who was drinkingand driving. In recent years, over 17,000 annual motorvehicle-related deaths have been associated with the useof alcohol, with more than 300,000 people injured.

Many adults -- by some estimates, nearly half the adultpopulation -- choose never to drink alcohol, so theynever drive after drinking. For persons under 21, it’sagainst the law in every U.S. state to drink alcohol.There are good medical, psychological anddevelopmental reasons for these laws.

The obvious way to solve the leading highway safetyproblem is for people never to drink alcohol and thendrive. But what if people do? How much is “too much”if the driver plans to drive? It’s a lot less than manymight think. Although it depends on each person and situation, here is some general information on the problem.

The Blood Alcohol Concentration (BAC) of someonewho is drinking depends upon four things:

� The amount of alcohol consumed

� The drinker’s body weight

� The amount of food that is consumed before andduring drinking

� The length of time it has taken the drinker toconsume the alcohol.

According to the American Medical Association, a180-lb. (82 kg) person who drinks three 12-ounce (355 ml) bottles of beer in an hour will end up with aBAC of about 0.06 percent. The person would reach thesame BAC by drinking three 4-ounce (120 ml) glassesof wine or three mixed drinks if each had 1-1/2 ounces(45 ml) of a liquor like whiskey, gin or vodka.

yellowblue

4-4

It’s the amount of alcohol that counts. For example, ifthe same person drank three double martinis (3 ouncesor 90 ml of liquor each) within an hour, the person’sBAC would be close to 0.12 percent. A person whoconsumes food just before or during drinking will have asomewhat lower BAC level.

There is a gender difference, too. Women generally havea lower relative percentage of body water than men.

Since alcohol is carried in body water, this means that awoman generally will reach a higher BAC level than aman of her same body weight when each has the samenumber of drinks.

The law in many U.S. states sets the legal limit at a BACof 0.10 percent. In a growing number of U.S. states, andthroughout Canada, the limit is 0.08 percent. In someother countries, it’s even lower. The BAC limit for allcommercial drivers in the United States is 0.04 percent.

The BAC will be over 0.10 percent after three to six drinks (in one hour). Of course, as we’ve seen, itdepends on how much alcohol is in the drinks, and howquickly the person drinks them.

But the ability to drive is affected well below a BAC of0.10 percent. Research shows that the driving skills ofmany people are impaired at a BAC approaching 0.05 percent, and that the effects are worse at night. Alldrivers are impaired at BAC levels above 0.05 percent.Statistics show that the chance of being in a collisionincreases sharply for drivers who have a BAC of 0.05 percent or above. A driver with a BAC level of0.06 percent has doubled his or her chance of having acollision. At a BAC level of 0.10 percent, the chance ofthis driver having a collision is 12 times greater; at alevel of 0.15 percent, the chance is 25 times greater!

yellowblue

4-5

The body takes about an hour to rid itself of the alcoholin one drink. No amount of coffee or number of coldshowers will speed that up. “I’ll be careful” isn’t theright answer. What if there’s an emergency, a need totake sudden action, as when a child darts into the street?A person with even a moderate BAC might not be ableto react quickly enough to avoid the collision.

There’s something else about drinking and driving thatmany people don’t know. Medical research shows thatalcohol in a person’s system can make crash injuriesworse, especially injuries to the brain, spinal cord orheart. This means that when anyone who has beendrinking -- driver or passenger -- is in a crash, thatperson’s chance of being killed or permanently disabledis higher than if the person had not been drinking.

CAUTION:

Drinking and then driving is very dangerous.Your reflexes, perceptions, attentiveness andjudgment can be affected by even a small amountof alcohol. You can have a serious -- or even fatal -- collision if you drive after drinking.Please don’t drink and drive or ride with a driverwho has been drinking. Ride home in a cab; or ifyou’re with a group, designate a driver who willnot drink.

yellowblue

4-6

Control of a VehicleYou have three systems that make your vehicle go whereyou want it to go. They are the brakes, the steering andthe accelerator. All three systems have to do their workat the places where the tires meet the road.

Sometimes, as when you’re driving on snow or ice, it’seasy to ask more of those control systems than the tiresand road can provide. That means you can lose controlof your vehicle.

BrakingBraking action involves perception time and reaction time.

First, you have to decide to push on the brake pedal.That’s perception time. Then you have to bring up yourfoot and do it. That’s reaction time.

Average reaction time is about 3/4 of a second. Butthat’s only an average. It might be less with one driverand as long as two or three seconds or more withanother. Age, physical condition, alertness, coordinationand eyesight all play a part. So do alcohol, drugs andfrustration. But even in 3/4 of a second, a vehiclemoving at 60 mph (100 km/h) travels 66 feet (20 m).That could be a lot of distance in an emergency, sokeeping enough space between your vehicle and othersis important.

And, of course, actual stopping distances vary greatlywith the surface of the road (whether it’s pavement orgravel); the condition of the road (wet, dry, icy); tiretread; the condition of your brakes; the weight of thevehicle and the amount of brake force applied.

yellowblue

4-7

Avoid needless heavy braking. Some people drive inspurts -- heavy acceleration followed by heavy braking -- rather than keeping pace with traffic. This is a mistake. Your brakes may not have time to coolbetween hard stops. Your brakes will wear out muchfaster if you do a lot of heavy braking. If you keep pacewith the traffic and allow realistic following distances,you will eliminate a lot of unnecessary braking. Thatmeans better braking and longer brake life.

If your engine ever stops while you’re driving, brakenormally but don’t pump your brakes. If you do, thepedal may get harder to push down. If your enginestops, you will still have some power brake assist. Butyou will use it when you brake. Once the power assist isused up, it may take longer to stop and the brake pedalwill be harder to push.

Anti-Lock Brakes (ABS)Your vehicle has anti-lock brakes (ABS). ABS is anadvanced electronic braking system that will helpprevent a braking skid.

When you start your engine and begin to drive away,your anti-lock brake system will check itself. You mayhear a momentary motor or clicking noise while this testis going on. This is normal.

If there’s a problem with theanti-lock brake system, thiswarning light will stay on.See “Anti-Lock BrakeSystem Warning Light” inthe Index.

yellowblue

4-8

Here’s how anti-lock works. Let’s say the road is wet.You’re driving safely. Suddenly an animal jumps out infront of you.

You slam on the brakes. Here’s what happens with ABS.

A computer senses that wheels are slowing down. If oneof the wheels is about to stop rolling, the computer willseparately work the brakes at each front wheel and atboth rear wheels.

The anti-lock system can change the brake pressurefaster than any driver could. The computer isprogrammed to make the most of available tire and road conditions.

You can steer around the obstacle while braking hard.

As you brake, your computer keeps receiving updates onwheel speed and controls braking pressure accordingly.

yellowblue

4-9

Remember: Anti-lock doesn’t change the time you needto get your foot up to the brake pedal or always decreasestopping distance. If you get too close to the vehicle infront of you, you won’t have time to apply your brakesif that vehicle suddenly slows or stops. Always leaveenough room up ahead to stop, even though you haveanti-lock brakes.

Using Anti-Lock

Don’t pump the brakes. Just hold the brake pedal downfirmly and let anti-lock work for you. You may feel thebrakes vibrate, or you may notice some noise, but this isnormal. On vehicles with four-wheel drive, youranti-lock brakes work at all times -- whether you are intwo-wheel drive or four-wheel drive.

Braking in EmergenciesWith anti-lock, you can steer and brake at the sametime. In many emergencies, steering can help you morethan even the very best braking.

SteeringPower SteeringIf you lose power steering assist because the enginestops or the system is not functioning, you can steer butit will take much more effort.

Steering Tips

Driving on Curves

It’s important to take curves at a reasonable speed.

A lot of the “driver lost control” accidents mentioned onthe news happen on curves. Here’s why:

Experienced driver or beginner, each of us is subject tothe same laws of physics when driving on curves. Thetraction of the tires against the road surface makes itpossible for the vehicle to change its path when you turnthe front wheels. If there’s no traction, inertia will keepthe vehicle going in the same direction. If you’ve evertried to steer a vehicle on wet ice, you’ll understand this.

The traction you can get in a curve depends on thecondition of your tires and the road surface, the angle atwhich the curve is banked, and your speed. While you’rein a curve, speed is the one factor you can control.

Suppose you’re steering through a sharp curve. Then yousuddenly accelerate. Both control systems -- steering andacceleration -- have to do their work where the tires meetthe road. Adding the sudden acceleration can demand toomuch of those places. You can lose control.

What should you do if this ever happens? Ease up on theaccelerator pedal, steer the vehicle the way you want itto go, and slow down.

yellowblue

4-10

Speed limit signs near curves warn that you shouldadjust your speed. Of course, the posted speeds arebased on good weather and road conditions. Under lessfavorable conditions you’ll want to go slower.

If you need to reduce your speed as you approach acurve, do it before you enter the curve, while your frontwheels are straight ahead.Try to adjust your speed so you can “drive” through thecurve. Maintain a reasonable, steady speed. Wait toaccelerate until you are out of the curve, and thenaccelerate gently into the straightaway.

Steering in EmergenciesThere are times when steering can be more effective thanbraking. For example, you come over a hill and find atruck stopped in your lane, or a car suddenly pulls outfrom nowhere, or a child darts out from between parkedcars and stops right in front of you. You can avoid theseproblems by braking -- if you can stop in time. Butsometimes you can’t; there isn’t room. That’s the time forevasive action -- steering around the problem.

Your vehicle can perform very well in emergencies likethese. First apply your brakes. (See “Braking inEmergencies” earlier in this section.) It is better toremove as much speed as you can from a possiblecollision. Then steer around the problem, to the left orright depending on the space available.

An emergency like this requires close attention and aquick decision. If you are holding the steering wheel atthe recommended 9 and 3 o’clock positions, you canturn it a full 180 degrees very quickly without removingeither hand. But you have to act fast, steer quickly, andjust as quickly straighten the wheel once you haveavoided the object.

The fact that such emergency situations are alwayspossible is a good reason to practice defensive driving atall times and wear safety belts properly.

yellowblue

4-11

Off -Road RecoveryYou may find that your right wheels have dropped off the edge of a road onto the shoulder while you’re driving.

If the level of the shoulder is only slightly below thepavement, recovery should be fairly easy. Ease off theaccelerator and then, if there is nothing in the way, steerso that your vehicle straddles the edge of the pavement.You can turn the steering wheel up to one-quarter turnuntil the right front tire contacts the pavement edge. Thenturn your steering wheel to go straight down the roadway.

PassingThe driver of a vehicle about to pass another on atwo-lane highway waits for just the right moment,accelerates, moves around the vehicle ahead, then goesback into the right lane again. A simple maneuver?

Not necessarily! Passing another vehicle on a two-lanehighway is a potentially dangerous move, since thepassing vehicle occupies the same lane as oncomingtraffic for several seconds. A miscalculation, an error injudgment, or a brief surrender to frustration or anger cansuddenly put the passing driver face to face with theworst of all traffic accidents -- the head-on collision.

So here are some tips for passing:

� “Drive ahead.” Look down the road, to the sides and to crossroads for situations that might affect yourpassing patterns. If you have any doubt whatsoeverabout making a successful pass, wait for a better time.

� Watch for traffic signs, pavement markings and lines.If you can see a sign up ahead that might indicate aturn or an intersection, delay your pass. A brokencenter line usually indicates it’s all right to pass(providing the road ahead is clear). Never cross a solidline on your side of the lane or a double solid line,even if the road seems empty of approaching traffic.

yellowblue

4-12

� Do not get too close to the vehicle you want to passwhile you’re awaiting an opportunity. For one thing,following too closely reduces your area of vision,especially if you’re following a larger vehicle. Also, you won’t have adequate space if the vehicleahead suddenly slows or stops. Keep back areasonable distance.

� When it looks like a chance to pass is coming up,start to accelerate but stay in the right lane and don’tget too close. Time your move so you will beincreasing speed as the time comes to move into theother lane. If the way is clear to pass, you will have a“running start” that more than makes up for thedistance you would lose by dropping back. And ifsomething happens to cause you to cancel your pass,you need only slow down and drop back again andwait for another opportunity.

� If other cars are lined up to pass a slow vehicle, waityour turn. But take care that someone isn’t trying topass you as you pull out to pass the slow vehicle.Remember to glance over your shoulder and checkthe blind spot.

� Check your mirrors, glance over your shoulder andstart your left lane change signal before moving outof the right lane to pass. When you are far enoughahead of the passed vehicle to see its front in yourinside mirror, activate your right lane change signaland move back into the right lane. (Remember that ifyour right outside mirror is convex, the vehicle youjust passed may seem to be farther away from youthan it really is.)

� Try not to pass more than one vehicle at a time ontwo-lane roads. Reconsider before passing the next vehicle.

� Don’t overtake a slowly moving vehicle too rapidly.Even though the brake lamps are not flashing, it maybe slowing down or starting to turn.

� If you’re being passed, make it easy for thefollowing driver to get ahead of you. Perhaps youcan ease a little to the right.

yellowblue

4-13

Loss of ControlLet’s review what driving experts say about whathappens when the three control systems (brakes, steeringand acceleration) don’t have enough friction where thetires meet the road to do what the driver has asked.

In any emergency, don’t give up. Keep trying to steerand constantly seek an escape route or area of less danger.

SkiddingIn a skid, a driver can lose control of the vehicle.Defensive drivers avoid most skids by taking reasonablecare suited to existing conditions, and by not“overdriving” those conditions. But skids are always possible.

The three types of skids correspond to your vehicle’sthree control systems. In the braking skid, your wheelsaren’t rolling. In the steering or cornering skid, toomuch speed or steering in a curve causes tires to slip andlose cornering force. And in the acceleration skid, toomuch throttle causes the driving wheels to spin.

A cornering skid and an acceleration skid are besthandled by easing your foot off the accelerator pedal.

If your vehicle starts to slide, ease your foot off theaccelerator pedal and quickly steer the way you want thevehicle to go. If you start steering quickly enough, yourvehicle may straighten out. Always be ready for asecond skid if it occurs.

Of course, traction is reduced when water, snow, ice,gravel or other material is on the road. For safety, you’llwant to slow down and adjust your driving to theseconditions. It is important to slow down on slipperysurfaces because stopping distance will be longer andvehicle control more limited.

While driving on a surface with reduced traction, tryyour best to avoid sudden steering, acceleration orbraking (including engine braking by shifting to a lowergear). Any sudden changes could cause the tires to slide.You may not realize the surface is slippery until your vehicle is skidding. Learn to recognize warningclues -- such as enough water, ice or packed snow onthe road to make a “mirrored surface” -- and slow down when you have any doubt.

Remember: Any anti-lock brake system (ABS) helpsavoid only the braking skid.

yellowblue

4-14

Off -Road Driving with YourFour-Wheel-Drive VehicleThis off-road guide is for vehicles that have four-wheel drive.

Also, see “Anti-Lock Brakes” in the Index.

If your vehicle doesn’t have four-wheel drive, youshouldn’t drive off-road unless you’re on a level, solid surface.

Off-road driving can be great fun. But it does have some definite hazards. The greatest of these is the terrain itself.

“Off -roading” means you’ve left the great NorthAmerican road system behind. Traffic lanes aren’tmarked. Curves aren’t banked. There are no road signs.Surfaces can be slippery, rough, uphill or downhill. In short, you’ve gone right back to nature.

Off-road driving involves some new skills. And that’swhy it’s very important that you read this guide. You’llfind many driving tips and suggestions. These will helpmake your off-road driving safer and more enjoyable.

If you think you will need some more ground clearanceat the front of your vehicle, you can easily remove thefront bumper lower air dam.

The front bumper lower air dam is held in place by aseries of push pins located around the lower edge of thefront bumper. The push-pins are accessible fromunderneath the front bumper.

yellowblue

4-15

The following steps must be performed on each of thepush-pins to remove the air dam:

1. Insert the blade portionof a flat-bladescrewdriver into thepush-pin slot and pulldownward until thepush-pin snaps loose.

2. While continuing to pulldownward on thepush-pin, squeeze androtate the expandableend of the push-pin with a pair of pliers until it releases from the retainer.

yellowblue

4-16

3. Pull the push-pins andlower air dam assemblyaway from the retainersuntil the lower air dam is free.

When you’re back on roads, though, be sure to replacethe air dam.

NOTICE:

Operating your vehicle for extended periodswithout the front bumper lower air dam installedcan cause improper air flow to the engine andmay allow things like fog lamps or tow hooks onthe front of your vehicle to be damaged. Alwaysbe sure to replace the front bumper air damwhen you’re finished off-road driving.

yellowblue

4-17

To replace the lower air dam:

1. Line up each push-pinwith it’s intendedretainer and push thewasher portion of thepush-pin towards theretainer until it locksinto place

2. Push the flat end of thepush-pin towards theretainer until it locksinto place, making sureeach is secure.

yellowblue

4-18

Before You Go Off-RoadingThere are some things to do before you go out. Forexample, be sure to have all necessary maintenance and service work done. Check to make sure allunderbody shields (if so equipped) are properlyattached. Be sure you read all the information aboutyour four-wheel-drive vehicle in this manual. Is thereenough fuel? Is the spare tire fully inflated? Are thefluid levels up where they should be? What are the locallaws that apply to off-roading where you’ll be driving?If you don’t know, you should check with lawenforcement people in the area. Will you be onsomeone’s private land? If so, be sure to get thenecessary permission.

Loading Your Vehicle for Off-Road DrivingThere are some important things to remember abouthow to load your vehicle.

� The heaviest things should be on the load floor andforward of your rear axle. Put heavier items as farforward as you can.

� Be sure the load is secured properly, so driving onthe off-road terrain doesn’t toss things around.

CAUTION:

� Cargo on the load floor piled higher thanthe seatbacks can be thrown forwardduring a sudden stop. You or yourpassengers could be injured. Keep cargobelow the top of the seatbacks.

� Unsecured cargo on the load floor can betossed about when driving over roughterrain. You or your passengers can bestruck by flying objects. Secure the cargo properly.

� Heavy loads on the roof raise the vehicle’scenter of gravity, making it more likely toroll over. You can be seriously or fatallyinjured if the vehicle rolls over. Put heavyloads inside the cargo area, not on the roof.Keep cargo in the cargo area as far forwardand low as possible.

You’ll find other important information in this manual.See “Vehicle Loading,” “Luggage Carrier” and “Tires”in the Index.

yellowblue

4-19

Environmental ConcernsOff-road driving can provide wholesome and satisfyingrecreation. However, it also raises environmentalconcerns. GM recognizes these concerns and urgesevery off-roader to follow these basic rules forprotecting the environment:

� Always use established trails, roads and areas thathave been specially set aside for public off-roadrecreational driving; obey all posted regulations.

� Avoid any driving practice that could damage theenvironment -- shrubs, flowers, trees, grasses -- ordisturb wildlife (this includes wheel-spinning,breaking down trees or unnecessary driving throughstreams or over soft ground).

� Always carry a litter bag . . . make sure all refuse isremoved from any campsite before leaving.

� Take extreme care with open fires (where permitted),camp stoves and lanterns.

� Never park your vehicle over dry grass or othercombustible materials that could catch fire from theheat of the vehicle’s exhaust system.

Traveling to Remote AreasIt makes sense to plan your trip, especially when goingto a remote area. Know the terrain and plan your route.You are much less likely to get bad surprises. Getaccurate maps of trails and terrain. Try to learn of anyblocked or closed roads.

It’s also a good idea to travel with at least one othervehicle. If something happens to one of them, the othercan help quickly.

Does your vehicle have a winch? If so, be sure to readthe winch instructions. In a remote area, a winch can behandy if you get stuck. But you’ll want to know how touse it properly.

yellowblue

4-20

Getting Familiar with Off-Road DrivingIt’s a good idea to practice in an area that’s safe andclose to home before you go into the wilderness.Off-road driving does require some new and differentdriving skills. Here’s what we mean.

Tune your senses to different kinds of signals. Youreyes, for example, need to constantly sweep the terrainfor unexpected obstacles. Your ears need to listen forunusual tire or engine sounds. With your arms, hands,feet and body, you’ll need to respond to vibrations andvehicle bounce.

Controlling your vehicle is the key to successfuloff-road driving. One of the best ways to control yourvehicle is to control your speed. Here are some things tokeep in mind. At higher speeds:

� you approach things faster and you have less time toscan the terrain for obstacles.

� you have less time to react.

� you have more vehicle bounce when you drive over obstacles.

� you’ll need more distance for braking, especiallysince you’re on an unpaved surface.

CAUTION:

When you’re driving off -road, bouncing andquick changes in direction can easily throw youout of position. This could cause you to losecontrol and crash. So, whether you’re driving onor off the road, you and your passengers shouldwear safety belts.

yellowblue

4-21

Scanning the TerrainOff-road driving can take you over many different kindsof terrain. You need to be familiar with the terrain and itsmany different features. Here are some things to consider.

Surface Conditions. Off-roading can take you overhard-packed dirt, gravel, rocks, grass, sand, mud, snow orice. Each of these surfaces affects the steering, accelerationand braking of your vehicle in different ways. Dependingupon the kind of surface you are on, you may experienceslipping, sliding, wheel spinning, delayed acceleration,poor traction and longer braking distances.

Surface Obstacles. Unseen or hidden obstacles can behazardous. A rock, log, hole, rut or bump can startle youif you’re not prepared for them. Often these obstacles arehidden by grass, bushes, snow or even the rise and fall ofthe terrain itself. Here are some things to consider:

� Is the path ahead clear?

� Will the surface texture change abruptly up ahead?

� Does the travel take you uphill or downhill? (There’smore discussion of these subjects later.)

� Will you have to stop suddenly or change direction quickly?

When you drive over obstacles or rough terrain, keep afirm grip on the steering wheel. Ruts, troughs or othersurface features can jerk the wheel out of your hands ifyou’re not prepared.

When you drive over bumps, rocks, or other obstacles,your wheels can leave the ground. If this happens, evenwith one or two wheels, you can’t control the vehicle aswell or at all.

Because you will be on an unpaved surface, it’sespecially important to avoid sudden acceleration,sudden turns or sudden braking.

In a way, off-road driving requires a different kind ofalertness from driving on paved roads and highways.There are no road signs, posted speed limits or signallights. You have to use your own good judgment aboutwhat is safe and what isn’t.

Drinking and driving can be very dangerous on anyroad. And this is certainly true for off-road driving. At the very time you need special alertness and drivingskills, your reflexes, perceptions and judgment can beaffected by even a small amount of alcohol. You couldhave a serious -- or even fatal -- accident if you drinkand drive or ride with a driver who has been drinking.See “Drunken Driving” in the Index.

yellowblue

4-22

Driving on Off-Road HillsOff-road driving often takes you up, down or across ahill. Driving safely on hills requires good judgment andan understanding of what your vehicle can and can’t do.There are some hills that simply can’t be driven, nomatter how well built the vehicle.

CAUTION:

Many hills are simply too steep for any vehicle. If you drive up them, you will stall. If you drivedown them, you can’t control your speed. If youdrive across them, you will roll over. You could beseriously injured or killed. If you have any doubtabout the steepness, don’t drive the hill.

Approaching a HillWhen you approach a hill, you need to decide if it’s oneof those hills that’s just too steep to climb, descend orcross. Steepness can be hard to judge. On a very smallhill, for example, there may be a smooth, constantincline with only a small change in elevation where you can easily see all the way to the top.

On a large hill, the incline may get steeper as you nearthe top, but you may not see this because the crest of thehill is hidden by bushes, grass or shrubs.

Here are some other things to consider as you approacha hill.

� Is there a constant incline, or does the hill get sharplysteeper in places?

� Is there good traction on the hillside, or will thesurface cause tire slipping?

� Is there a straight path up or down the hill so youwon’t have to make turning maneuvers?

� Are there obstructions on the hill that can block yourpath (boulders, trees, logs or ruts)?

� What’s beyond the hill? Is there a cliff, anembankment, a drop-off, a fence? Get out and walkthe hill if you don’t know. It’s the smart way to find out.

� Is the hill simply too rough? Steep hills often haveruts, gullies, troughs and exposed rocks because theyare more susceptible to the effects of erosion.

yellowblue

4-23

Driving UphillOnce you decide you can safely drive up the hill, youneed to take some special steps.

� Use a low gear and get a firm grip on the steering wheel.

� Get a smooth start up the hill and try to maintainyour speed. Don’t use more power than you need,because you don’t want your wheels to start spinningor sliding.

� Try to drive straight up the hill if at all possible. If the path twists and turns, you might want to findanother route.

CAUTION:

Turning or driving across steep hills can bedangerous. You could lose traction, slidesideways, and possibly roll over. You could beseriously injured or killed. When driving up hills,always try to go straight up.

� Ease up on your speed as you approach the top of the hill.

� Attach a flag to the vehicle to make you more visibleto approaching traffic on trails or hills.

� Sound the horn as you approach the top of the hill tolet opposing traffic know you’re there.

� Use your headlamps even during the day. They makeyou more visible to oncoming traffic.

CAUTION:

Driving to the top (crest) of a hill at full speed cancause an accident. There could be a drop-off,embankment, cliff, or even another vehicle. Youcould be seriously injured or killed. As you nearthe top of a hill, slow down and stay alert.

yellowblue

4-24

Q: What should I do if my vehicle stalls, or is aboutto stall, and I can’t make it up the hill?

A: If this happens, there are some things you shoulddo, and there are some things you must not do.First, here’s what you should do:

� Push the brake pedal to stop the vehicle and keep itfrom rolling backwards. Also, apply the parking brake.

� If your engine is still running, shift the transmissionto REVERSE (R), release the parking brake, andslowly back down the hill in REVERSE (R).

� If your engine has stopped running, you’ll need torestart it. With the brake pedal pressed and theparking brake still applied, shift the transmission toPARK (P) (or, shift to NEUTRAL (N) if yourvehicle has a manual transmission) and restart theengine. Then, shift to REVERSE (R), release theparking brake, and slowly back down the hill asstraight as possible in REVERSE (R).

� As you are backing down the hill, put your left hand on the steering wheel at the 12 o’clock position. This way, you’ll be able to tell if your wheels are straight and maneuver as you back down. It’s best that you back down the hill with your wheels straight rather than in the left or right direction. Turning the wheel too far to the left or right will increase the possibility of a rollover.

Here are some things you must not do if you stall, or areabout to stall, when going up a hill.

� Never attempt to prevent a stall by shifting intoNEUTRAL (N) (or depressing the clutch, if youhave a manual transmission) to “rev-up” the engineand regain forward momentum. This won’t work.Your vehicle will roll backwards very quickly andyou could go out of control.

Instead, apply the regular brake to stop the vehicle. Thenapply the parking brake. Shift to REVERSE (R), releasethe parking brake, and slowly back straight down.

� Never attempt to turn around if you are about to stallwhen going up a hill. If the hill is steep enough tostall your vehicle, it’s steep enough to cause you toroll over if you turn around. If you can’t make it upthe hill, you must back straight down the hill.

yellowblue

4-25

Q: Suppose, after stalling, I try to back down thehill and decide I just can’t do it. What should I do?

A: Set the parking brake, put your transmission inPARK (P) (or the manual transmission in FIRST (1)) and turn off the engine. Leave thevehicle and go get some help. Exit on the uphillside and stay clear of the path the vehicle wouldtake if it rolled downhill. Do not shift the transfercase to NEUTRAL (N) when you leave the vehicle.Leave it in some gear.

CAUTION:

Shifting the transfer case to NEUTRAL (N) cancause your vehicle to roll even if the transmissionis in PARK (P) (or, if you have the manualtransmission, even if you’re in gear). This isbecause the NEUTRAL (N) position on thetransfer case overrides the transmission. You orsomeone else could be injured. If you are going toleave your vehicle, set the parking brake andshift the transmission to PARK (P) (or, put yourmanual transmission in FIRST (1)). But do notshift the transfer case to the NEUTRAL (N)position. Leave the transfer case in the 2 WheelHigh, 4 High or 4 Low position.

yellowblue

4-26

Driving DownhillWhen off-roading takes you downhill, you’ll want toconsider a number of things:

� How steep is the downhill? Will I be able to maintainvehicle control?

� What’s the surface like? Smooth? Rough? Slippery?Hard-packed dirt? Gravel?

� Are there hidden surface obstacles? Ruts? Logs? Boulders?

� What’s at the bottom of the hill? Is there a hiddencreek bank or even a river bottom with large rocks?

If you decide you can go down a hill safely, then try tokeep your vehicle headed straight down, and use a lowgear. This way, engine drag can help your brakes andthey won’t have to do all the work. Descend slowly,keeping your vehicle under control at all times.

CAUTION:

Heavy braking when going down a hill can causeyour brakes to overheat and fade. This couldcause loss of control and a serious accident. Applythe brakes lightly when descending a hill and usea low gear to keep vehicle speed under control.

Q: Are there some things I should not do whendriving down a hill?

A: Yes! These are important because if you ignorethem you could lose control and have a serious accident.

� When driving downhill, avoid turns that take youacross the incline of the hill. A hill that’s not toosteep to drive down may be too steep to drive across.You could roll over if you don’t drive straight down.

� Never go downhill with the transmission inNEUTRAL (N), or with the clutch pedal depressedin a manual shift. This is called “free-wheeling.”Your brakes will have to do all the work and couldoverheat and fade.

yellowblue

4-27

Q: Am I likely to stall when going downhill?

A: It’s much more likely to happen going uphill. But ifit happens going downhill, here’s what to do.

� Stop your vehicle by applying the regular brakes.Apply the parking brake.

� Shift to PARK (P) (or to NEUTRAL (N) with themanual transmission) and, while still braking, restartthe engine.

� Shift back to a low gear, release the parking brake,and drive straight down.

� If the engine won’t start, get out and get help.

Driving Across an InclineSooner or later, an off-road trail will probably go acrossthe incline of a hill. If this happens, you have to decidewhether to try to drive across the incline. Here are somethings to consider:

� A hill that can be driven straight up or down may betoo steep to drive across. When you go straight up ordown a hill, the length of the wheel base (thedistance from the front wheels to the rear wheels)reduces the likelihood the vehicle will tumble endover end. But when you drive across an incline, themuch more narrow track width (the distance betweenthe left and right wheels) may not prevent the vehiclefrom tilting and rolling over. Also, driving across anincline puts more weight on the downhill wheels.This could cause a downhill slide or a rollover.

� Surface conditions can be a problem when you driveacross a hill. Loose gravel, muddy spots, or even wetgrass can cause your tires to slip sideways, downhill.If the vehicle slips sideways, it can hit somethingthat will trip it (a rock, a rut, etc.) and roll over.

yellowblue

4-28

� Hidden obstacles can make the steepness of theincline even worse. If you drive across a rock withthe uphill wheels, or if the downhill wheels drop intoa rut or depression, your vehicle can tilt even more.

For reasons like these, you need to decide carefullywhether to try to drive across an incline. Just becausethe trail goes across the incline doesn’t mean you haveto drive it. The last vehicle to try it might have rolled over.

CAUTION:

Driving across an incline that’s too steep willmake your vehicle roll over. You could beseriously injured or killed. If you have any doubtabout the steepness of the incline, don’t driveacross it. Find another route instead.

Q: What if I’m driving across an incline that’s nottoo steep, but I hit some loose gravel and start toslide downhill. What should I do?

A: If you feel your vehicle starting to slide sideways,turn downhill. This should help straighten out thevehicle and prevent the side slipping. However, amuch better way to prevent this is to get out and“walk the course” so you know what the surface islike before you drive it.

yellowblue

4-29

Stalling on an InclineIf your vehicle stalls when you’re crossing an incline, besure you (and your passengers) get out on the uphillside, even if the door there is harder to open. If you getout on the downhill side and the vehicle starts to rollover, you’ll be right in its path.

If you have to walk down the slope, stay out of the paththe vehicle will take if it does roll over.

CAUTION:

Getting out on the downhill (low) side of a vehiclestopped across an incline is dangerous. If thevehicle rolls over, you could be crushed or killed.Always get out on the uphill (high) side of thevehicle and stay well clear of the rollover path.

Driving in Mud, Sand, Snow or IceWhen you drive in mud, snow or sand, your wheels won’tget good traction. You can’t accelerate as quickly, turningis more difficult, and you’ll need longer braking distances.

It’s best to use a low gear when you’re in mud -- thedeeper the mud, the lower the gear. In really deep mud, theidea is to keep your vehicle moving so you don’t get stuck.

When you drive on sand, you’ll sense a change in wheeltraction. But it will depend upon how loosely packed thesand is. On loosely packed sand (as on beaches or sanddunes) your tires will tend to sink into the sand. This hasan effect on steering, accelerating and braking. You maywant to reduce the air pressure in your tires slightlywhen driving on sand. This will improve traction.

yellowblue

4-30

Hard packed snow and ice offer the worst tire traction.On these surfaces, it’s very easy to lose control. On wetice, for example, the traction is so poor that you willhave difficulty accelerating. And if you do get moving,poor steering and difficult braking can cause you to slideout of control.

CAUTION:

Driving on frozen lakes, ponds or rivers can bedangerous. Underwater springs, currents underthe ice, or sudden thaws can weaken the ice. Yourvehicle could fall through the ice and you andyour passengers could drown. Drive your vehicleon safe surfaces only.

Driving in WaterLight rain causes no special off-road driving problems.But heavy rain can mean flash flooding, and floodwaters demand extreme caution.

Find out how deep the water is before you drive throughit. If it’s deep enough to cover your wheel hubs, axles orexhaust pipe, don’t try it -- you probably won’t getthrough. Also, water that deep can damage your axleand other vehicle parts.

If the water isn’t too deep, then drive through it slowly.At fast speeds, water splashes on your ignition systemand your vehicle can stall. Stalling can also occur if youget your tailpipe under water. And, as long as yourtailpipe is under water, you’ll never be able to start yourengine. When you go through water, remember that whenyour brakes get wet, it may take you longer to stop.

CAUTION:

Driving through rushing water can be dangerous.Deep water can sweep your vehicle downstreamand you and your passengers could drown. If it’sonly shallow water, it can still wash away theground from under your tires, and you could losetraction and roll the vehicle over. Don’t drivethrough rushing water.

See “Driving Through Water” in the Index for moreinformation on driving through water.

yellowblue

4-31

After Off-Road DrivingRemove any brush or debris that has collected on theunderbody, chassis or under the hood. Theseaccumulations can be a fire hazard.

After operation in mud or sand, have the brake liningscleaned and checked. These substances can causeglazing and uneven braking. Check the body structure,steering, suspension, wheels, tires and exhaust systemfor damage. Also, check the fuel lines and coolingsystem for any leakage.

Your vehicle will require more frequent service due tooff-road use. Refer to the Maintenance Schedule foradditional information.

Driving at Night

Night driving is more dangerous than day driving. One reason is that some drivers are likely to be impaired -- by alcohol or drugs, with night visionproblems, or by fatigue.

yellowblue

4-32

Here are some tips on night driving.

� Drive defensively.

� Don’t drink and drive.

� Adjust your inside rearview mirror to reduce theglare from headlamps behind you.

� Since you can’t see as well, you may need to slowdown and keep more space between you and other vehicles.

� Slow down, especially on higher speed roads. Yourheadlamps can light up only so much road ahead.

� In remote areas, watch for animals.

� If you’re tired, pull off the road in a safe place and rest.

No one can see as well at night as in the daytime. But aswe get older these differences increase. A 50-year-olddriver may require at least twice as much light to see thesame thing at night as a 20-year-old.

What you do in the daytime can also affect your nightvision. For example, if you spend the day in brightsunshine you are wise to wear sunglasses. Your eyes willhave less trouble adjusting to night. But if you’redriving, don’t wear sunglasses at night. They may cutdown on glare from headlamps, but they also make a lotof things invisible.

You can be temporarily blinded by approachingheadlamps. It can take a second or two, or even severalseconds, for your eyes to readjust to the dark. When youare faced with severe glare (as from a driver whodoesn’t lower the high beams, or a vehicle withmisaimed headlamps), slow down a little. Avoid staringdirectly into the approaching headlamps.

Keep your windshield and all the glass on your vehicleclean -- inside and out. Glare at night is made muchworse by dirt on the glass. Even the inside of the glasscan build up a film caused by dust. Dirty glass makeslights dazzle and flash more than clean glass would,making the pupils of your eyes contract repeatedly.

Remember that your headlamps light up far less of aroadway when you are in a turn or curve. Keep youreyes moving; that way, it’s easier to pick out dimlylighted objects. Just as your headlamps should bechecked regularly for proper aim, so should your eyesbe examined regularly. Some drivers suffer from nightblindness -- the inability to see in dim light -- and aren’teven aware of it.

yellowblue

4-33

Driving in Rain and on Wet Roads Rain and wet roads can mean driving trouble. On a wetroad, you can’t stop, accelerate or turn as well becauseyour tire-to-road traction isn’t as good as on dry roads.And, if your tires don’t have much tread left, you’ll geteven less traction. It’s always wise to go slower and becautious if rain starts to fall while you are driving. Thesurface may get wet suddenly when your reflexes aretuned for driving on dry pavement.

The heavier the rain, the harder it is to see. Even if yourwindshield wiper blades are in good shape, a heavy raincan make it harder to see road signs and traffic signals,pavement markings, the edge of the road and evenpeople walking.

It’s wise to keep your wiping equipment in good shapeand keep your windshield washer tank filled withwasher fluid. Replace your windshield wiper insertswhen they show signs of streaking or missing areas onthe windshield, or when strips of rubber start to separatefrom the inserts.

yellowblue

4-34

Driving too fast through large water puddles or evengoing through some car washes can cause problems, too.The water may affect your brakes. Try to avoid puddles.But if you can’t, try to slow down before you hit them.

CAUTION:

Wet brakes can cause accidents. They won’t workas well in a quick stop and may cause pulling toone side. You could lose control of the vehicle.

After driving through a large puddle of water ora car wash, apply your brake pedal lightly untilyour brakes work normally.

yellowblue

4-35

HydroplaningHydroplaning is dangerous. So much water can build upunder your tires that they can actually ride on the water.This can happen if the road is wet enough and you’regoing fast enough. When your vehicle is hydroplaning,it has little or no contact with the road.

Hydroplaning doesn’t happen often. But it can if yourtires do not have much tread or if the pressure in one ormore is low. It can happen if a lot of water is standing onthe road. If you can see reflections from trees, telephonepoles or other vehicles, and raindrops “dimple” thewater’s surface, there could be hydroplaning.

Hydroplaning usually happens at higher speeds. Therejust isn’t a hard and fast rule about hydroplaning. Thebest advice is to slow down when it is raining.

Driving Through Deep Standing Water

NOTICE:

If you drive too quickly through deep puddles orstanding water, water can come in through yourengine’s air intake and badly damage yourengine. Never drive through water that is slightlylower than the underbody of your vehicle. If youcan’t avoid deep puddles or standing water, drivethrough them very slowly.

yellowblue

4-36

Driving Through Flowing Water

CAUTION:

Flowing or rushing water creates strong forces. If you try to drive through flowing water, as youmight at a low water crossing, your vehicle can becarried away. As little as six inches of flowingwater can carry away a smaller vehicle. If thishappens, you and the other vehicle occupantscould drown. Don’t ignore police warning signs,and otherwise be very cautious about trying todrive through flowing water.

Some Other Rainy Weather Tips� Turn on your low-beam headlamps -- not just your

parking lamps -- to help make you more visible to others.

� Besides slowing down, allow some extra followingdistance. And be especially careful when you passanother vehicle. Allow yourself more clear roomahead, and be prepared to have your view restrictedby road spray.

� Have good tires with proper tread depth. (See “Tires” in the Index.)

yellowblue

4-37

City Driving

One of the biggest problems with city streets is theamount of traffic on them. You’ll want to watch out forwhat the other drivers are doing and pay attention totraffic signals.

Here are ways to increase your safety in city driving:

� Know the best way to get to where you are going.Get a city map and plan your trip into an unknown part of the city just as you would for a cross-country trip.

� Try to use the freeways that rim and crisscross mostlarge cities. You’ll save time and energy. (See thenext part, “Freeway Driving.”)

� Treat a green light as a warning signal. A traffic lightis there because the corner is busy enough to need it.When a light turns green, and just before you start tomove, check both ways for vehicles that have notcleared the intersection or may be running the red light.

yellowblue

4-38

Freeway Driving

Mile for mile, freeways (also called thruways, parkways,expressways, turnpikes or superhighways) are the safestof all roads. But they have their own special rules.

The most important advice on freeway driving is: Keepup with traffic and keep to the right. Drive at the samespeed most of the other drivers are driving. Too-fast ortoo-slow driving breaks a smooth traffic flow. Treat theleft lane on a freeway as a passing lane.

At the entrance, there is usually a ramp that leads to thefreeway. If you have a clear view of the freeway as youdrive along the entrance ramp, you should begin tocheck traffic. Try to determine where you expect toblend with the flow. Try to merge into the gap at close tothe prevailing speed. Switch on your turn signal, checkyour mirrors and glance over your shoulder as often asnecessary. Try to blend smoothly with the traffic flow.

Once you are on the freeway, adjust your speed to theposted limit or to the prevailing rate if it’s slower. Stayin the right lane unless you want to pass.

Before changing lanes, check your mirrors. Then useyour turn signal.

Just before you leave the lane, glance quickly over yourshoulder to make sure there isn’t another vehicle in your“blind” spot.

Once you are moving on the freeway, make certain youallow a reasonable following distance. Expect to moveslightly slower at night.

When you want to leave the freeway, move to the properlane well in advance. If you miss your exit, do not,under any circumstances, stop and back up. Drive on tothe next exit.

The exit ramp can be curved, sometimes quite sharply.

yellowblue

4-39

The exit speed is usually posted.

Reduce your speed according to your speedometer, notto your sense of motion. After driving for any distanceat higher speeds, you may tend to think you are goingslower than you actually are.

Before Leaving on a Long TripMake sure you’re ready. Try to be well rested. If youmust start when you’re not fresh -- such as after a day’swork -- don’t plan to make too many miles that first partof the journey. Wear comfortable clothing and shoes youcan easily drive in.

Is your vehicle ready for a long trip? If you keep itserviced and maintained, it’s ready to go. If it needsservice, have it done before starting out. Of course,you’ll find experienced and able service experts in GMdealerships all across North America. They’ll be readyand willing to help if you need it.

Here are some things you can check before a trip:

� Windshield Washer Fluid: Is the reservoir full? Are all windows clean inside and outside?

� Wiper Blades: Are they in good shape?

� Fuel, Engine Oil, Other Fluids: Have you checkedall levels?

� Lamps: Are they all working? Are the lenses clean?

� Tires: They are vitally important to a safe,trouble-free trip. Is the tread good enough forlong-distance driving? Are the tires all inflated to therecommended pressure?

� Weather Forecasts: What’s the weather outlookalong your route? Should you delay your trip a shorttime to avoid a major storm system?

� Maps: Do you have up-to-date maps?

yellowblue

4-40

Highway HypnosisIs there actually such a condition as “highwayhypnosis”? Or is it just plain falling asleep at the wheel? Call it highway hypnosis, lack of awareness, or whatever.

There is something about an easy stretch of road withthe same scenery, along with the hum of the tires on theroad, the drone of the engine, and the rush of the windagainst the vehicle that can make you sleepy. Don’t let ithappen to you! If it does, your vehicle can leave theroad in less than a second, and you could crash and be injured.

What can you do about highway hypnosis? First, beaware that it can happen.

Then here are some tips:

� Make sure your vehicle is well ventilated, with acomfortably cool interior.

� Keep your eyes moving. Scan the road ahead and to the sides. Check your mirrors and yourinstruments frequently.

� If you get sleepy, pull off the road into a rest, serviceor parking area and take a nap, get some exercise, orboth. For safety, treat drowsiness on the highway asan emergency.

Hill and Mountain Roads

Driving on steep hills or mountains is different fromdriving in flat or rolling terrain.

If you drive regularly in steep country, or if you’replanning to visit there, here are some tips that can makeyour trips safer and more enjoyable. (See “Off-RoadDriving” in the Index for information about driving off-road.)

yellowblue

4-41

� Keep your vehicle in good shape. Check all fluidlevels and also the brakes, tires, cooling system andtransmission. These parts can work hard onmountain roads.

� Know how to go down hills. The most importantthing to know is this: let your engine do some of theslowing down. Shift to a lower gear when you godown a steep or long hill.

CAUTION:

If you don’t shift down, your brakes could get sohot that they wouldn’t work well. You would then have poor braking or even none going down a hill. You could crash. Shift down to letyour engine assist your brakes on a steepdownhill slope.

CAUTION:

Coasting downhill in NEUTRAL (N) or with theignition off is dangerous. Your brakes will have todo all the work of slowing down. They could get sohot that they wouldn’t work well. You would thenhave poor braking or even none going down a hill.You could crash. Always have your engine runningand your vehicle in gear when you go downhill.

� Know how to go uphill. You may want to shift downto a lower gear. The lower gears help cool your engineand transmission, and you can climb the hill better.

� Stay in your own lane when driving on two-laneroads in hills or mountains. Don’t swing wide or cutacross the center of the road. Drive at speeds that letyou stay in your own lane.

� As you go over the top of a hill, be alert. There could besomething in your lane, like a stalled car or an accident.

� You may see highway signs on mountains that warn ofspecial problems. Examples are long grades, passing orno-passing zones, a falling rocks area or windingroads. Be alert to these and take appropriate action.

yellowblue

4-42

Winter Driving Here are some tips for winter driving:

� Have your vehicle in good shape for winter.

� You may want to put winter emergency supplies inyour vehicle.

Include an ice scraper, a small brush or broom, a supplyof windshield washer fluid, a rag, some winter outerclothing, a small shovel, a flashlight, a red cloth andreflective warning triangles. And, if you will be drivingunder severe conditions, include a small bag of sand, apiece of old carpet or a couple of burlap bags to helpprovide traction. Be sure you properly secure theseitems in your vehicle.

Driving on Snow or IceMost of the time, those places where your tires meet theroad probably have good traction.

However, if there is snow or ice between your tires andthe road, you can have a very slippery situation. You’llhave a lot less traction or “grip” and will need to be very careful.

yellowblue

4-43

What’s the worst time for this? “Wet ice.” Very coldsnow or ice can be slick and hard to drive on. But wetice can be even more trouble because it may offer theleast traction of all. You can get wet ice when it’s aboutfreezing (32�F; 0�C) and freezing rain begins to fall.Try to avoid driving on wet ice until salt and sand crewscan get there.

Whatever the condition -- smooth ice, packed, blowingor loose snow -- drive with caution.

Accelerate gently. Try not to break the fragile traction. If you accelerate too fast, the drive wheels will spin andpolish the surface under the tires even more.

Your anti-lock brakes improve your vehicle’s stabilitywhen you make a hard stop on a slippery road. Eventhough you have an anti-lock braking system, you’llwant to begin stopping sooner than you would on drypavement. See “Anti-Lock” in the Index.

� Allow greater following distance on any slippery road.

� Watch for slippery spots. The road might be fineuntil you hit a spot that’s covered with ice. On anotherwise clear road, ice patches may appear inshaded areas where the sun can’t reach: aroundclumps of trees, behind buildings or under bridges.Sometimes the surface of a curve or an overpass mayremain icy when the surrounding roads are clear. Ifyou see a patch of ice ahead of you, brake before youare on it. Try not to brake while you’re actually onthe ice, and avoid sudden steering maneuvers.

yellowblue

4-44

If You’re Caught in a Blizzard

If you are stopped by heavy snow, you could be in aserious situation. You should probably stay with yourvehicle unless you know for sure that you are near helpand you can hike through the snow. Here are somethings to do to summon help and keep yourself and yourpassengers safe:

� Turn on your hazard flashers.

� Tie a red cloth to your vehicle to alert police thatyou’ve been stopped by the snow.

� Put on extra clothing or wrap a blanket around you.If you have no blankets or extra clothing, make bodyinsulators from newspapers, burlap bags, rags, floormats -- anything you can wrap around yourself ortuck under your clothing to keep warm.

You can run the engine to keep warm, but be careful.

yellowblue

4-45

CAUTION:

Snow can trap exhaust gases under your vehicle.This can cause deadly CO (carbon monoxide) gasto get inside. CO could overcome you and killyou. You can’t see it or smell it, so you might notknow it is in your vehicle. Clear away snow fromaround the base of your vehicle, especially anythat is blocking your exhaust pipe. And checkaround again from time to time to be sure snowdoesn’t collect there.Open a window just a little on the side of thevehicle that’s away from the wind. This will helpkeep CO out.

Run your engine only as long as you must. This savesfuel. When you run the engine, make it go a little fasterthan just idle. That is, push the accelerator slightly. Thisuses less fuel for the heat that you get and it keeps thebattery charged. You will need a well-charged battery torestart the vehicle, and possibly for signaling later onwith your headlamps. Let the heater run for a while.

Then, shut the engine off and close the window almostall the way to preserve the heat. Start the engine againand repeat this only when you feel really uncomfortablefrom the cold. But do it as little as possible. Preserve thefuel as long as you can. To help keep warm, you can getout of the vehicle and do some fairly vigorous exercisesevery half hour or so until help comes.

yellowblue

4-46

Recreational Vehicle TowingThere may be times when you want to tow your vehiclebehind another vehicle for use at your destination. Besure to use the proper towing equipment designed forrecreational vehicle towing. Follow the instructions forthe towing equipment.

When towing your vehicle, turn the ignition to OFF. To prevent your battery from draining while towing,remove the IGN 0 fuse from the instrument panel fuseblock. Be sure to replace the fuse when you reach yourdestination. See “Fuses and Circuit Breakers” in the Index.

Two-Wheel-Drive VehiclesTwo-wheel-drive vehicles, should not be towed with all four wheels on the ground. Two-wheel-drivetransmissions have no provisions for internal lubricationwhile being towed. To properly tow these vehicles, theyshould be placed on a platform trailer with all fourwheels off the ground.

In rare cases when it’s unavoidable that atwo-wheel-drive vehicle is to be towed with all fourwheels on the ground, the propeller shaft to axle yokeorientation should be marked and the propeller shaftremoved following the applicable service manualremoval/installation procedure.

Dust or dirt can enter the back of the transmissionthrough the opening created by removing the propellershaft if proper protection is not provided. Also, checkthe transmission fluid level before driving the truck.

yellowblue

4-47

Four-Wheel-Drive Vehicles

CAUTION:

Shifting the transfer case into NEUTRAL (N) cancause your vehicle to roll even if the transmissionis in PARK (P), for an automatic transmission, or if your vehicle is in gear, for a manualtransmission. You or others could be injured.Make sure the parking brake is firmly set beforeyou shift the transfer case into NEUTRAL (N).

Use the following procedure to correctly tow yourvehicle on all four wheels:

1. Firmly set the parking brake.

2. Shift an automatic transmission to PARK (P), or amanual transmission to FIRST (1).

3. Securely attach the vehicle being towed to the tow vehicle.

4. Shift the transfer case to NEUTRAL (N). See“Four-Wheel Drive” in the Index for the properprocedure to select the neutral position for your vehicle.

5. Release the parking brake only after the vehiclebeing towed is firmly attached to the towing vehicle.

6. Turn the ignition to OFF. The OFF position unlocksthe steering column and reduces battery drain as longas the IGN 0 fuse is removed. Unlocking the steeringcolumn will allow the proper movement of the frontwheels and tires during towing.

yellowblue

4-48

Loading Your Vehicle

The Certification/Tire label is found on the rear edge ofthe driver’s door or in the Incomplete Vehicle Documentin the cab.

The label shows the size of your original tires and theinflation pressures needed to obtain the gross weightcapacity of your vehicle. This is called the GVWR(Gross Vehicle Weight Rating). The GVWR includes theweight of the vehicle, all occupants, fuel and cargo.

The Certification/Tire label also tells you the maximumweights for the front and rear axles, called Gross AxleWeight Rating (GAWR). To find out the actual loads onyour front and rear axles, you need to go to a weighstation and weigh your vehicle. Your dealer can helpyou with this. Be sure to spread out your load equally onboth sides of the centerline.

Never exceed the GVWR for your vehicle, or theGAWR for either the front or rear axle.

The Certification/Tire label also contains informationabout your Front Axle Reserve Capacity. See “FrontAxle Reserve Capacity” later in this section.

And, if you do have a heavy load, you should spread it out.

CAUTION:

In the case of a sudden stop or collision, thingscarried in the bed of your truck could shiftforward and come into the passenger area,injuring you and others. If you put things in thebed of your truck, you should make sure they areproperly secured.

yellowblue

4-49

NOTICE:

Some vehicles may be equipped with RPO VYU(snow plow prep package). With this option, thepayload your vehicle can carry is reduced when asnow plow is installed. Your vehicle can bedamaged if either the front or rear axle ratings,or the GVW are exceeded.As a general guideline, with a 650 lb. (295 kg)snow plow, the weight of the occupants and cargomust not exceed 300 lb. (135 kg). However, thismay depend on the vehicle’s option content.Therefore, to help avoid vehicle damage:

� Make sure the weight on the front and rearaxles does not exceed their respective axle ratings.

NOTICE: (Continued)

NOTICE: (Continued)

� For the front axle, if more cargo orpassengers need to be carried, appropriatecounter ballast must be installed rear of therear axle and properly secured.

� Total vehicle weight must not exceed theGVW rating.

� See your dealer for advice and informationabout using a snow plow on your vehicle.

CAUTION:

Do not load your vehicle any heavier than theGVWR, or either the maximum front or rearGAWR. If you do, parts on your vehicle canbreak, and it can change the way your vehiclehandles. These could cause you to lose controland crash. Also, overloading can shorten the lifeof your vehicle.

yellowblue

4-50

Your warranty does not cover parts or components thatfail because of overloading.

This will help you decide how much cargo and installedequipment your truck can carry.

Using heavier suspension components to get addeddurability might not change your weight ratings. Askyour dealer to help you load your vehicle the right way.

If you put things inside your vehicle -- like suitcases,tools, packages, or anything else -- they go as fast as thevehicle goes. If you have to stop or turn quickly, or ifthere is a crash, they’ll keep going.

CAUTION:

Things you put inside your vehicle can strike and injure people in a sudden stop or turn, or in a crash.

� Put things in the cargo area of your vehicle.Try to spread the weight evenly.

� Never stack heavier things, like suitcases,inside the vehicle so that some of them areabove the tops of the seats.

� Don’t leave an unsecured child restraint inyour vehicle.

� When you carry something inside thevehicle, secure it whenever you can.

� Don’t leave a seat folded down unless youneed to.

There’s also important loading information for off-roaddriving in this manual. See “Loading Your Vehicle forOff-Road Driving” in the Index.

yellowblue

4-51

Front Axle Reserve CapacityThis is the difference between your front GAWR and thefront axle weight of your truck with full fuel andpassengers. It is the amount of weight you can add toyour front axle before reaching your front GAWR.

The front axle reservecapacity for your vehiclecan be found in the lowerright corner of thetire/certification label, asshown in this example.

In order to calculate the amount of weight any frontaccessory is adding to the front axle, use the following formula.

(W x (A+W.B.)) / W.B.= Weight the accessory is addingto the front axle

Where: W= Weight of added accessory

A= Distance that the accessory isin front of the front axle

W.B.= Vehicle Wheelbase

yellowblue

4-52

For example, adding a 700 lbs. (318 kg) snow plow adds more than 700 lbs. (318 kg) to the front axle. Using the formula, if the snow plow is 4 ft. (122 cm) in front of the front axle and the wheel base is 10 ft. (305 cm), then:

W= 700 lbs. (318 kg), A= 4 ft. (122 cm) and W.B.= 10 ft. (305 cm)

(W x (A+W.B.)) / W.B. = (700 x (4ft. + 10 ft.)) / 10 ft. = 980 lbs.

So, if your truck’s front axle reserve capacity is morethan 980 lbs. (445 kg), you could add this snow plowwithout exceeding the front GAWR.

You can add heavier equipment on the front of thevehicle if you compensate for it by carrying fewerpassengers, less cargo or by positioning cargo moretowards the rear. This has the effect of reducing the loadon the front. However, the front GAWR, rear GAWRand the GVWR must never be exceeded.

Total Vehicle Reserve CapacityThis is the difference between your GVWR and theweight of your truck with full fuel and passengers. It isthe amount of weight you can add to your vehicle beforereaching your GVWR.

The reserve capacity numbers are intended as a guidewhen selecting the amount of equipment or cargo yourtruck can carry. If you are unsure of your truck’s front,rear or total weight, go to a weigh station and weighyour vehicle. Your dealer can help you with this.

Truck-Camper Loading InformationThis label is inside your glove box. It will tell you ifyour vehicle can carry a slide-in camper, how much of aload your vehicle can carry, and how to correctly spreadout your load. Also, it will help you match the rightslide-in camper to your vehicle.

When you carry a slide-in camper, the total cargo loadof your vehicle is the weight of the camper, plus

� everything else added to the camper after it left the factory,

� everything in the camper and

� all the people inside.

yellowblue

4-53

The Cargo Weight Rating (CWR) is the maximumweight of the load your vehicle can carry. It doesn’tinclude the weight of the people inside. But, you canfigure about 150 lbs. (68 kg) for each seat.

The total cargo load must not be more than yourvehicle’s CWR.

Refer to the Truck-Camper Loading Information label inglove box for dimensions A and B as shown in thefollowing illustration.

Use the rear edge of the load floor for measurementpurposes. The recommended location for the cargo centerof gravity is at point C for the CWR. It is the point wherethe mass of a body is concentrated and, if suspended atthat point, would balance the front and rear.

Here is an example of proper truck and camper match:

A. Camper Center of Gravity

B. Recommended Center of Gravity Location Zone

The camper’s center of gravity should fall within thecenter of gravity zone for your vehicle’s cargo load.

You must weigh any accessories or other equipment thatyou add to your vehicle. Then, subtract this extra weightfrom the CWR. This extra weight may shorten thecenter of gravity zone of your vehicle. Your dealer canhelp you with this.

If your slide-in camper and its load weighs less than theCWR, the center of gravity zone for your vehicle maybe larger.

yellowblue

4-54

Your dealer can help you make a good vehicle-campermatch. He’ll also help you determine your CWR.

After you’ve loaded your vehicle and camper, drive to aweigh station and weigh the front and rear wheelsseparately. This will tell you the loads on your axles.The loads on the front and rear axles shouldn’t be morethan either of the GAWRs. The total of the axle loadsshould not be more than the GVWR.

Open your driver’s door and look at theCertification/Tire label to find out your GAWR and GVWR.

If you’ve gone over your weight ratings, move or takeout some things until all the weight falls below theratings. Of course, you should always tie down anyloose items when you load your vehicle or camper.

When you install and load your slide-in camper, checkthe manufacturer’s instructions.

If you want more information on curb weights, cargoweights, Cargo Weight Rating and the correct center ofgravity zone for your vehicle, your dealer can help you.Just ask for a copy of “Consumer Information,Truck-Camper Loading.”

Trailer RecommendationsYou must subtract your hitch loads from the CWR foryour vehicle. Weigh your vehicle with the trailerattached, so that you won’t go over the GVWR orGAWR. If you are using a weight-distributing hitch,weigh the vehicle without the equalizer bars in place.

You’ll get the best performance if you spread out theweight of your load the right way, and if you choose thecorrect hitch and trailer brakes.

For more information, see “Trailer Towing” in the Index.

Camper Wiring Harness (If Equipped)If your vehicle is equipped with a camper wiring harnesssee “Trailer Wiring Harness” in the Index for further information.

yellowblue

4-55

Pickup Conversion to Chassis CabGeneral Motors is aware that some vehicle owners mayconsider having the pickup box removed and acommercial or recreational body installed. Before youdo so, first contact the GM Customer Assistance Officefor your area for information on such conversionsspecific to this vehicle. (See the “Warranty and OwnerAssistance” booklet for Customer Assistance Office.)Owners should be aware that, as manufactured, there aredifferences between a chassis cab and a pickup with thebox removed which may affect vehicle safety. Thecomponents necessary to adapt a pickup to permit itssafe use with a specialized body should be installed by abody builder in accordance with the informationavailable from the Customer Assistance Office.

Towing a Trailer

CAUTION:

If you don’t use the correct equipment and drive properly, you can lose control when you pull a trailer. For example, if the trailer is too heavy, the brakes may not work well -- or even at all. You and your passengers could be seriously injured. Pull a trailer only if you have followed all the steps in this section. Ask your dealer for advice and information about towing a trailer with your vehicle.

NOTICE:

Pulling a trailer improperly can damage yourvehicle and result in costly repairs not covered byyour warranty. To pull a trailer correctly, followthe advice in this part, and see your dealer forimportant information about towing a trailerwith your vehicle.

yellowblue

4-56

Your vehicle may be able to tow a trailer. To identifywhat the vehicle trailering capacity is for your vehicle,you should read the information in “Weight of theTrailer” that appears later in this section.

If yours was built with trailering options, as many are,it’s ready for heavier trailers. But trailering is differentthan just driving your vehicle by itself. Trailering meanschanges in handling, durability and fuel economy.Successful, safe trailering takes correct equipment, andit has to be used properly.

That’s the reason for this part. In it are manytime-tested, important trailering tips and safety rules.Many of these are important for your safety and that ofyour passengers. So please read this section carefullybefore you pull a trailer.

If You Do Decide To Pull A TrailerIf you do, here are some important points:

� There are many different laws, including speed limitrestrictions, having to do with trailering. Make sureyour rig will be legal, not only where you live butalso where you’ll be driving. A good source for thisinformation can be state or provincial police.

� Consider using a sway control if your trailer willweigh less than the capacity stamped on your stepbumper. You should always use a sway control ifyour trailer will weigh more than the capacitystamped on your step bumper. You can ask a hitchdealer about sway controls.

� Don’t tow a trailer at all during the first 500 miles(800 km) your new vehicle is driven. Your engine,axle or other parts could be damaged.

� Then, during the first 500 miles (800 km) that youtow a trailer, don’t drive over 50 mph (80 km/h) anddon’t make starts at full throttle. This helps yourengine and other parts of your vehicle wear in at theheavier loads.

� If you have an automatic transmission, you can tow in DRIVE (D). You may want to shift thetransmission to THIRD (3) or, if necessary, a lowergear selection if the transmission shifts too often(e.g., under heavy loads and/or hilly conditions). If you have a manual transmission and you aretowing a trailer, it’s better not to use FIFTH (5) gear.Just drive in FOURTH (4) gear (or, as you need to, a lower gear). See “Tow/Haul Mode” in the Index.

yellowblue

4-57

Three important considerations have to do with weight:

� the weight of the trailer,

� the weight of the trailer tongue

� and the weight on your vehicle’s tires.

Tow/Haul Mode (If Equipped)

Tow/haul is a feature on automatic transmissionequipped vehicles that assists when pulling a heavytrailer or a large or heavy load. The purpose of thetow/haul mode is to:

� Reduce the frequency and improve the predictabilityof transmission shifts when pulling a heavy trailer ora large or heavy load.

� Provide the same solid shift feel when pulling aheavy trailer or a large or heavy load as when thevehicle is unloaded.

� Improve control of vehicle speed while requiring lessthrottle pedal activity when pulling a heavy trailer ora large or heavy load.

Automatic transmission equipped vehicles are providedwith a button at the end of the shift lever which whenpressed enables tow/haul. When the button is pressed, a light on the instrument panel will illuminate to indicate that tow/haul has been selected.

Tow/haul may be turned off by pressing the buttonagain, at which time the indicator light on the instrumentpanel will turn off. The vehicle will automatically turnoff tow/haul every time it is started.

Tow/haul is designed to be most effective when thevehicle and trailer combined weight is at least 75% ofthe vehicle’s Gross Combined Weight Rating (GCWR).Tow/haul is most useful under the following driving conditions:

� When pulling a heavy trailer or a large or heavy loadthrough rolling terrain.

� When pulling a heavy trailer or a large or heavy loadin stop and go traffic.

� When pulling a heavy trailer or a large or heavy loadin busy parking lots where improved low speedcontrol of the vehicle is desired.

Operating the vehicle in tow/haul when lightly loaded orwith no trailer at all will not cause damage. However,there is no benefit to the selection of tow/haul when thevehicle is unloaded. Such a selection when unloadedmay result in unpleasant engine and transmissiondriving characteristics and reduced fuel economy.Tow/haul is recommended only when pulling a heavytrailer or a large or heavy load.

yellowblue

4-58

Weight of the TrailerHow heavy can a trailer safely be?

It depends on how you plan to use your rig. Forexample, speed, altitude, road grades, outsidetemperature and how much your vehicle is used to pull atrailer are all important. And, it can also depend on anyspecial equipment that you have on your vehicle.

Use one of the following charts to determine how muchyour vehicle can weigh, based upon your vehicle modeland options.

Maximum trailer weight is calculated assuming thedriver and one passenger are in the tow vehicle and ithas all the required trailering equipment. The weight ofadditional optional equipment, passengers and cargo inthe tow vehicle must be subtracted from the maximumtrailer weight.

Above the 5,000 lbs. (2 268 kg) trailer rating, thehandling/trailering suspension is required on C-1500models and the handling/trailering or off-roadsuspension is required on K-1500 models. The engineoil cooler is required on C/K-2500 models with theVORTEC 6000 engine. Refer to the Trailering Guide foroil cooler recommendations.

C-1500 (2WD)*

Engine (Trans.) Axle Ratio

Max. Trailer Wt.

4300 V6 (Auto) 3.08 4,000 lbs. (1 814 kg)

3.42 4,500 lbs. (2 041 kg)

3.73 5,000 lbs. (2 268 kg)

4300 V6 (Manual) 3.08 3,500 lbs. (1 588 kg)

3.42 4,000 lbs. (1 814 kg)

4800 V8 (Auto) 3.42 6,000 lbs. (2 722 kg)

3.73 7,000 lbs. (3 175 kg)

4800 V8 (Manual) 3.42 4,000 lbs. (1 814 kg)

3.73 5,000 lbs. (2 268 kg)

5300 V8 3.42 7,000 lbs. (3 175 kg)

3.73 8,200 lbs. (3 720 kg)

* Weight-distributing hitch tongue weight 10% to 15%of hitch pulling weight 1,000 lb. (454 kg) maximum.Fifth-wheel hitch tongue weight 15% to 25% of hitchpulling weight 1,500 lb (680 kg) maximum.

yellowblue

4-59

K-1500 (4WD)*

Engine (Trans.) Axle Ratio

Max. Trailer Wt.

4300 V6 (Auto) 3.42 4,000 lbs. (1 814 kg)

3.73 4,500 lbs. (2 041 kg)

4300 V6 (Manual) 3.42 3,500 lbs. (1 588 kg)

3.73 4,000 lbs. (1 814 kg)

4800 V8 (Auto) 3.73 6,500 lbs. (2 948 kg)

4.10 7,500 lbs. (3 402 kg)

4800 V8 (Manual) 3.73 4,500 lbs. (2 041 kg)

4.10 5,500 lbs. (2 495 kg)

5300 V8 3.73 7,500 lbs. (3 402 kg)

4.10 8,000 lbs. (3 629 kg)

* Weight-distributing hitch tongue weight 10% to 15%of hitch pulling weight 1,000 lb. (454 kg) maximum.Fifth-wheel hitch tongue weight 15% to 25% of hitchpulling weight 1,500 lb (680 kg) maximum.

C-2500 LD (2WD)*

Engine Axle Ratio

Max. Trailer Wt.

5300 V8 3.42 6,500 lbs. (2 948 kg)

3.73 7,500 lbs. (3 402 kg)

4.10 8,500 lbs. (3 856 kg)

6000 V8 3.42 7,500 lbs. (3 402 kg)

3.73 8,500 lbs. (3 856 kg)

4.10 10,500 lbs. (4 763 kg)

6.5 L Diesel 3.42 7,500 lbs. (3 402 kg)

* Weight-distributing hitch tongue weight 10% to 15%of hitch pulling weight 1,200 lb. (544 kg) maximum.Fifth-wheel hitch tongue weight 15% to 25% of hitchpulling weight 2,000 lb (907 kg) maximum.

yellowblue

4-60

C-2500 HD (2WD)*

Engine Axle Ratio

Max. Trailer Wt.

6000 V8 3.42 7,500 lbs. (3 402 kg)

3.73 8,500 lbs. (3 856 kg)

4.10 10,500 lbs. (4 763 kg)

6.5 L Diesel 3.42 11,000 lbs. (4 990 kg)

4.10 11,000 lbs. (4 990 kg)

* Weight-distributing hitch tongue weight 10% to 15% of hitch weight 1,200 lb. (544 kg) maximum.Fifth-wheel hitch tongue weight 15% to 25% of hitchweight 2,500 lb (1 134 kg) maximum.

K-2500 HD (4WD)*

Engine Axle Ratio

Max. Trailer Wt.

6000 V8 3.73 8,000 lbs. (3 629 kg)

4.10 10,000 lbs. (4 536 kg)

6.5 L Diesel 3.42 10,500 lbs. (4 763 kg)

4.10 10,500 lbs. (4 763 kg)

* Weight-distributing hitch tongue weight 10% to 15% of hitch weight 1,200 lb. (544 kg) maximum.Fifth-wheel hitch tongue weight 15% to 25% of hitchweight 2,500 lb (1 134 kg) maximum.

You can ask your dealer for our trailering information oradvice, or you can write us at the address listed in yourWarranty and Owner Assistance Information Booklet.

In Canada, write to:

General Motors of Canada LimitedCustomer Communication Centre1908 Colonel Sam DriveOshawa, Ontario L1H 8P7

yellowblue

4-61

Weight of the Trailer TongueThe tongue load (A) of any trailer is an importantweight to measure because it affects the total or grossweight of your vehicle. The Gross Vehicle Weight(GVW) includes the curb weight of the vehicle, anycargo you may carry in it, and the people who will beriding in the vehicle. And if you will tow a trailer, youmust add the tongue load to the GVW because yourvehicle will be carrying that weight, too. See “LoadingYour Vehicle” in the Index for more information aboutyour vehicle’s maximum load capacity.

If you’re using a weight-carrying or aweight-distributing hitch, the trailer tongue weight (A)should be 10 percent to 15 percent of the total loadedtrailer weight (B). Do not exceed the maximumallowable tongue weight for your vehicle.

After you’ve loaded your trailer, weigh the trailer andthen the tongue, separately, to see if the weights areproper. If they aren’t, you may be able to get them rightsimply by moving some items around in the trailer.

Total Weight on Your Vehicle’s TiresBe sure your vehicle’s tires are inflated to the upperlimit for cold tires. You’ll find these numbers on theCertification label at the rear edge of the driver’s door orsee “Tire Loading” in the Index. Then be sure you don’tgo over the GVW limit for your vehicle, including theweight of the trailer tongue.

yellowblue

4-62

HitchesIt’s important to have the correct hitch equipment.Crosswinds, large trucks going by and rough roads are afew reasons why you’ll need the right hitch. Here aresome rules to follow:

� If you use a step-bumper hitch, your bumper couldbe damaged in sharp turns. Make sure you haveample room when turning to avoid contact betweenthe trailer and the bumper.

� If you’ll be pulling a trailer that, when loaded, willweigh more than the capacity stamped on your stepbumper, be sure to use a properly mounted,weight-distributing hitch and sway control of theproper size. This equipment is very important forproper vehicle loading and good handling whenyou’re driving.

Safety ChainsYou should always attach chains between your vehicleand your trailer. Cross the safety chains under the tongueof the trailer to help prevent the tongue from contactingthe road if it becomes separated from the hitch.Instructions about safety chains may be provided by thehitch manufacturer or by the trailer manufacturer. If youhave the factory-installed trailering package, and for

trailers up to 5,000 lbs. (2 270 kg) you may attach thesafety chains to the attaching points on the bumper. Forheavier trailers, follow the trailer or hitch manufacturer’srecommendation for attaching safety chains. Alwaysleave just enough slack so you can turn with your rig.Never allow safety chains to drag on the ground.

Trailer BrakesIf your trailer weighs more than 2,000 lbs. (900 kg)loaded, then it needs its own brakes -- and they must beadequate. Be sure to read and follow the instructions forthe trailer brakes so you’ll be able to install, adjust andmaintain them properly.

Your trailer brake system can tap into the vehicle’shydraulic brake system only if:

� The trailer parts can withstand 3,000 psi (20 650 kPa) of pressure.

� The trailer’s brake system will use less than 0.02 cubic inch (0.3 cc) of fluid from your vehicle’smaster cylinder. Otherwise, both braking systemswon’t work well. You could even lose your brakes.

If everything checks out this far, make the brake tap at theport on the master cylinder that sends the fluid to the rearbrakes. But don’t use copper tubing for this. If you do, itwill bend and finally break off. Use steel brake tubing.

yellowblue

4-63

Driving with a TrailerTowing a trailer requires a certain amount of experience.Before setting out for the open road, you’ll want to getto know your rig. Acquaint yourself with the feel ofhandling and braking with the added weight of thetrailer. And always keep in mind that the vehicle you aredriving is now a good deal longer and not nearly asresponsive as your vehicle is by itself.

Before you start, check the trailer hitch and platform(and attachments), safety chains, electrical connector,lamps, tires and mirror adjustment. If the trailer haselectric brakes, start your vehicle and trailer moving andthen apply the trailer brake controller by hand to be surethe brakes are working. This lets you check yourelectrical connection at the same time.

During your trip, check occasionally to be sure that theload is secure, and that the lamps and any trailer brakesare still working.

While towing a trailer or when exposed to long periodsof sunshine, the floor of the truck bed may become verywarm. Avoid putting items in the truck bed that might beaffected by high ambient temperatures.

Following DistanceStay at least twice as far behind the vehicle ahead as youwould when driving your vehicle without a trailer. Thiscan help you avoid situations that require heavy brakingand sudden turns.

PassingYou’ll need more passing distance up ahead whenyou’re towing a trailer. And, because you’re a good deallonger, you’ll need to go much farther beyond thepassed vehicle before you can return to your lane.

Backing UpHold the bottom of the steering wheel with one hand.Then, to move the trailer to the left, just move that handto the left. To move the trailer to the right, move yourhand to the right. Always back up slowly and, ifpossible, have someone guide you.

yellowblue

4-64

Making Turns

NOTICE:

Making very sharp turns while trailering couldcause the trailer to come in contact with thevehicle. Your vehicle could be damaged. Avoidmaking very sharp turns while trailering.

When you’re turning with a trailer, make wider turnsthan normal. Do this so your trailer won’t strike softshoulders, curbs, road signs, trees or other objects.Avoid jerky or sudden maneuvers. Signal well in advance.

Turn Signals When Towing a TrailerThe arrows on your instrument panel will flashwhenever you signal a turn or lane change. Properlyhooked up, the trailer lamps will also flash, telling otherdrivers you’re about to turn, change lanes or stop.

When towing a trailer, the arrows on your instrumentpanel will flash for turns even if the bulbs on the trailerare burned out. Thus, you may think drivers behind youare seeing your signal when they are not. It’s importantto check occasionally to be sure the trailer bulbs are still working.

Driving On GradesReduce speed and shift to a lower gear before you startdown a long or steep downgrade. If you don’t shiftdown, you might have to use your brakes so much thatthey would get hot and no longer work well.

If you have an automatic transmission, you can tow inDRIVE (D). You may want to shift the transmission toTHIRD (3) or, if necessary, a lower gear selection if thetransmission shifts too often (e.g., under heavy loadsand/or hilly conditions).

You may also want to activate the tow/haul mode if thetransmission shifts too often. See “Tow/Haul Mode” inthe Index.

If you have a manual transmission and you are towing atrailer, it’s better not to use FIFTH (5) gear. Just drive inFOURTH (4) gear (or, as you need to, a lower gear).

yellowblue

4-65

When towing at high altitude on steep uphill grades,consider the following: Engine coolant will boil at alower temperature than at normal altitudes. If you turnyour engine off immediately after towing at high altitudeon steep uphill grades, your vehicle may show signssimilar to engine overheating. To avoid this, let theengine run while parked (preferably on level ground)with the automatic transmission in PARK (P) (or themanual transmission out of gear and the parking brakeapplied) for a few minutes before turning the engine off.If you do get the overheat warning, see “EngineOverheating” in the Index.

Parking on Hills

CAUTION:

You really should not park your vehicle, with atrailer attached, on a hill. If something goeswrong, your rig could start to move. People canbe injured, and both your vehicle and the trailercan be damaged.

But if you ever have to park your rig on a hill, here’show to do it:

1. Apply your regular brakes, but don’t shift into PARK (P) yet for an automatic transmission, or intogear for a manual transmission.

2. Have someone place chocks under the trailer wheels.

3. When the wheel chocks are in place, release theregular brakes until the chocks absorb the load.

4. Reapply the regular brakes. Then apply your parking brake and shift into PARK (P) for anautomatic transmission, or REVERSE (R) for amanual transmission.

5. If you have a four-wheel-drive vehicle, be sure the transfer case is in a drive gear and not inNEUTRAL (N).

6. Release the regular brakes.

yellowblue

4-66

CAUTION:

It can be dangerous to get out of your vehicle ifthe shift lever is not fully in PARK (P) with theparking brake firmly set. Your vehicle can roll.

If you have left the engine running, the vehiclecan move suddenly. You or others could beinjured. To be sure your vehicle won’t move, evenwhen you’re on fairly level ground, use the stepsthat follow.

Always put the shift lever fully in PARK (P) withthe parking brake firmly set.If the transfer case on four-wheel drive vehicles isin NEUTRAL (N), your vehicle will be free toroll, even if your shift lever is in PARK (P). So, besure the transfer case is in a drive gear -- not inNEUTRAL (N).

When You Are Ready to Leave AfterParking on a Hill1. Apply your regular brakes and hold the pedal down

while you:

� Start your engine;

� Shift into a gear; and

� Release the parking brake.

2. Let up on the brake pedal.

3. Drive slowly until the trailer is clear of the chocks.

4. Stop and have someone pick up and store the chocks.

Maintenance When Trailer TowingYour vehicle will need service more often when you’repulling a trailer. See the Maintenance Schedule for moreon this. Things that are especially important in traileroperation are automatic transmission fluid (don’toverfill), engine oil, axle lubricant, belt, cooling systemand brake system. Each of these is covered in thismanual, and the Index will help you find them quickly.If you’re trailering, it’s a good idea to review thesesections before you start your trip.

Check periodically to see that all hitch nuts and bolts are tight.

yellowblue

4-67

Trailer Wiring HarnessYour vehicle is equipped with one of the followingwiring harnesses for towing a trailer or hauling aslide-in camper.

Basic Trailer Wiring Package

All regular and extended cab pickups have a six-wiretrailer towing harness.

The six-wire harness is located at the rear of the vehicleand is tied to the vehicle’s frame. The harness requiresthe installation of a trailer-wiring harness connector,which is available through your dealer.

The six-wire harness contains the following trailer circuits:

� Yellow: Left Stop/Turn Signal

� Dark Green: Right Stop/Turn Signal

� Brown: Taillamps

� White: Ground

� Light Green: Back-up Lamps

� Light Blue: Center High-Mounted Stoplamp (CHMSL)

If you need to upgrade your vehicle to heavy-dutytrailering, a brake controller harness and an underbodyharness with a seven-pin universal heavy-duty trailerconnector are available from your dealer.

yellowblue

4-68

Heavy-Duty Trailer Wiring Package (If Equipped)

Your pickup may be equipped with the eight-wire trailertowing harness. This harness with a seven-pin universalheavy-duty trailer connector is attached to a bracket onthe platform hitch.*

* The Center High-Mounted Stoplamp (CHMSL) wireis tied next to the trailer wiring harness for use with atrailer, slide-in camper or cap.

The eight-wire harness contains the following trailer circuits:

� Yellow: Left Stop/Turn Signal

� Dark Green: Right Stop/Turn Signal

� Brown: Taillamps

� White: Ground

� Light Green: Back-up Lamps

� Light Blue: CHMSL

� Red: Battery Feed

� Dark Blue: Trailer Brake

A jumper harness for an electric trailer brake controllerand a trailer battery feed fuse are included with thistrailering package. (See“Instrument Panel JumperWiring Harness” later in this section.)

If you need to tow a light-duty trailer with a standardfour-way round pin connector, an adapter connector isavailable from your dealer.

yellowblue

4-69

Camper/Fifth-Wheel Trailer Wiring Package (If Equipped)

The eight-wire camper harness is located under the frontedge of the pickup box on the driver’s side of thevehicle, attached to the frame bracket. A connector willhave to be added to the wiring harness which connectsto the camper.

The eight-wire harness contains the followingcamper/trailer circuits:

� Yellow: Left Stop/Turn Signal

� Dark Green: Right Stop/Turn Signal

� Brown: Taillamps

� White: Ground

� Light Green: Back-up Lamps

� Light Blue: Center High-Mounted Stoplamp (CHMSL)

� Red: Battery Feed

� Dark Blue: Trailer Brake

A jumper harness for an electric trailer brake controllerand a trailer battery feed fuse are included with thistrailering package. (See“Instrument Panel JumperWiring Harness” later in this section.)

If your vehicle is equipped with the “Heavy-DutyTrailering” option, please refer to “Heavy-Duty TrailerWiring Package”, earlier in this section.

When the camper-wiring harness is ordered without theheavy-duty trailering package, an eight-wire harnesswith a seven-pin connector and separate CHMSLconnector are located at the rear of the vehicle and aretied to the vehicle’s frame.

yellowblue

4-70

Instrument Panel Jumper Wiring Harness

This harness is included with the heavy-duty andcamper/fifth-wheel trailer wiring packages. The harnessis for an electric trailer brake controller and includes atrailer battery feed fuse. This harness and fuse should beinstalled by your dealer or a qualified service center.

Auxiliary Battery (If Equipped)The auxiliary battery provision can be used to supplyelectrical power to additional equipment that you maychoose to add, such as a slide-in camper.

If your vehicle has thisprovision, this relay will belocated on the passenger’sside of the vehicle, next tothe auxiliary battery.

When using this provision, connection should only bemade to the upper stud (A) of the relay. Do not makeconnections to the lower stud (B) of the relay.

The auxiliary battery circuit is protected by a megafuselocated behind the auxiliary battery.

Be sure to follow the proper installation instructions that are included with any electrical equipment that you install.

yellowblue

4-71

NOTICE:

When using the auxiliary battery provision, theelectrical load must not exceed 30 amps. Alwaysturn off any electrical equipment when not in use.Leaving electrical equipment on for extendedperiods will drain your battery.

Power WinchesIf you wish to use a power winch on your vehicle, onlyuse it when your vehicle is stationary or anchored.

NOTICE:

Using a power winch with the transmission ingear may damage the transmission. Whenoperating a power winch, always leave thetransmission in NEUTRAL (N).

Use the regular brakes, set the parking brake, or blockthe wheels to keep your vehicle from rolling.

Step-Bumper PadIf your vehicle has a rear step bumper, it may beequipped with a rear step pad at the center of the bumper.

If you will be using thebumper to tow a trailer, youmust remove the centercutout circle to install thetrailer ball.

5-

yellowblue

5-1

Section 5 Problems on the Road

Here you’ll find what to do about some problems that can occur on the road.

5-2 Hazard Warning Flashers5-2 Other Warning Devices5-3 Jump Starting5-8 Towing Your Vehicle5-9 Engine Overheating

5-12 Cooling System5-18 Engine Fan Noise5-18 If a Tire Goes Flat5-18 Changing a Flat Tire5-34 If You’re Stuck: In Sand, Mud, Ice or Snow

yellowblue

5-2

Hazard Warning Flashers

Your hazard warning flashers let you warn others. Theyalso let police know you have a problem. Your front andrear turn signal lamps will flash on and off.

But they won’t flash if you’re braking.

Press the button at the topof the steering column allthe way down to make yourfront and rear turn signallamps flash on and off.

Your hazard warning flashers work no matter whatposition your key is in, and even if the key isn’t in.

To turn off the flashers, press the button until the firstclick and release.

When the hazard warning flashers are on, your turnsignals won’t work.

Other Warning DevicesIf you carry reflective triangles, you can use them towarn others. Set one up at the side of the road about 300 feet (100 m) behind your vehicle.

yellowblue

5-3

Jump StartingIf your battery has run down, you may want to useanother vehicle and some jumper cables to start yourvehicle. But please use the following steps to do it safely.

CAUTION:

Batteries can hurt you. They can be dangerous because:� They contain acid that can burn you.� They contain gas that can explode or ignite.� They contain enough electricity to

burn you.If you don’t follow these steps exactly, some or allof these things can hurt you.

NOTICE:

Ignoring these steps could result in costly damageto your vehicle that wouldn’t be covered by your warranty.

The ACDelco� battery in your vehicle has abuilt -in hydrometer. Do not charge, test or jumpstart the battery if the hydrometer looks clear orlight yellow. Replace the battery when there is a clear or light yellow hydrometer and a cranking complaint.Trying to start your vehicle by pushing or pullingit won’t work, and it could damage your vehicle.

1. Check the other vehicle. It must have a 12-voltbattery with a negative ground system.

NOTICE:

If the other system isn’t a 12-volt system with anegative ground, both vehicles can be damaged.

yellowblue

5-4

2. Get the vehicles close enough so the jumper cablescan reach, but be sure the vehicles aren’t touchingeach other. If they are, it could cause a groundconnection you don’t want. You wouldn’t be able tostart your vehicle, and the bad grounding coulddamage the electrical systems.

To avoid the possibility of the vehicles rolling, setthe parking brake firmly on both vehicles involved inthe jump start procedure. Put an automatictransmission in PARK (P) or a manual transmissionin NEUTRAL (N). If you have a four-wheel-drivevehicle, be sure the transfer case is not inNEUTRAL (N).

3. Turn off the ignition on both vehicles. Unplugunnecessary accessories plugged into the cigarettelighter or accessory power outlets. Turn off all lampsthat aren’t needed as well as radios. This will avoidsparks and help save both batteries. In addition, itcould save your radio!

NOTICE:

If you leave your radio on, it could be badlydamaged. The repairs wouldn’t be covered byyour warranty.

4. Open the hoods and locate the positive (+) andnegative (-) terminal locations on the other vehicle.

Your vehicle has a remote positive (+) jump startingterminal and a remote negative (-) jump startingterminal. The remote positive (+) terminal is locatedbehind a red plastic cover near the engine accessorydrive bracket. To uncover the remote positive (+)terminal, open the red plastic cover.

On all V8 engines, the remote negative (-) terminalis located on the engine accessory drive bracket. Thisis marked “GND” on V8 engines. On V6 engines,the remote negative (-) terminal is located on a tabattached to the engine accessory drive bracket whereit is marked “GND”.

You should always use the remote positive (+) and theremote negative (-) terminals instead of the positive (+)and negative (-) terminals on your battery.

yellowblue

5-5

CAUTION:

Using a match near a battery can cause batterygas to explode. People have been hurt doing this,and some have been blinded. Use a flashlight ifyou need more light.Be sure the battery has enough water. You don’tneed to add water to the ACDelco� batteryinstalled in every new GM vehicle. But if abattery has filler caps, be sure the right amountof fluid is there. If it is low, add water to take care of that first. If you don’t, explosive gas couldbe present.

Battery fluid contains acid that can burn you.Don’t get it on you. If you accidentally get it inyour eyes or on your skin, flush the place withwater and get medical help immediately.

5. Check that the jumper cables don’t have loose ormissing insulation. If they do, you could get a shock.The vehicles could be damaged too.

Before you connect the cables, here are some basicthings you should know. Positive (+) will go topositive (+) or a remote positive terminal if thevehicle has one. Negative (-) will go to a metalengine part or a remote negative terminal if thevehicle has one. Don’t connect positive (+) tonegative (-) or you’ll get a short that would damagethe battery and maybe other parts too.

On vehicles equipped with dual batteries, make allbattery connections to the remote positive (+) andremote negative (-) terminals.

CAUTION:

Fans or other moving engine parts can injure youbadly. Keep your hands away from moving partsonce the engine is running.

yellowblue

5-6

6. Connect the red positive (+) cable to thepositive (+) terminal ofthe vehicle with the deadbattery. Use a remotepositive (+) terminal ifthe vehicle has one.

7. Don’t let the other endtouch metal. Connect itto the positive (+)terminal of the goodbattery. Use a remotepositive (+) terminal ifthe vehicle has one.

8. Now connect the blacknegative (-) cable to the good battery’snegative (-) cable. Use aremote negative (-)terminal if the vehiclehas one.

Don’t let the other end touch anything until the nextstep. The other end of the negative (-) cable doesn’t goto the dead battery. It goes to a heavy unpainted metalpart of the vehicle with the dead battery or to a remotenegative (-) terminal if the vehicle has one.

yellowblue

5-7

V8 Engine V6 Engine

9. When connecting the cable, be sure it is not nearany engine parts that will move.

10. Now start the vehicle with the good battery and runthe engine for awhile.

11. Try to start the vehicle with the dead battery. If it won’t start after a few tries, it probably needs service.

12. Remove the cables in reverse order to preventelectrical shorting. Take care that they don’t toucheach other or any other metal.

A. Heavy Metal Engine Part

B. Good Battery

C. Dead Battery

yellowblue

5-8

Towing Your Vehicle

CAUTION:

To help avoid serious personal injury to you or others:� Never let passengers ride in a vehicle that is

being towed.� Never tow faster than safe or posted speeds.� Never tow with damaged parts not

fully secured.� Never get under your vehicle after it has

been lifted by the tow truck.� Always secure the vehicle on each side with

separate safety chains when towing it.� Use only the correct hooks.

NOTICE:

Use the proper towing equipment to avoiddamage to the bumper, fascia or fog lamp areasof the vehicle.

With current trends in automotive styles and design, it isessential that the correct towing equipment is used totow a vehicle. Your vehicle can be towed with wheel liftequipment or car carrier equipment. Two-Wheel-Drivevehicle towing limits for wheel lift equipment are as follows:

� Front Towing -- 35 mph (55 km/h) for 50 miles (80 km)

� Rear Towing -- 55 mph (88 km/h) or legal speedlimit. The distance is unlimited.

yellowblue

5-9

Four-Wheel-Drive vehicles must have the transfer casein NEUTRAL (N). See “Four-Wheel Drive” in theIndex for the proper procedure to select the NEUTRALposition for your vehicle. The towing limits forfour-wheel-drive vehicles with wheel lift equipment:

� Front Towing -- 55 mph (88 km/h) or legal speed limit and distance is unlimited

� Rear Towing -- 55 mph (88 km/h) for 50 miles (80 km).

Consult your dealer or a professional towing service ifyou need to have your vehicle towed. See “RoadsideAssistance” in the Index.

Engine OverheatingYou will find a coolant temperature gage on yourvehicle’s instrument panel. See “Engine CoolantTemperature Gage” in the Index. In addition, you willfind a LOW COOLANT, CHECK COOLANT TEMP,ENGINE OVERHEATED and a REDUCED ENGINEPOWER message in the message center on theinstrument panel. See “Message Center” in the Index.

Overheated Engine Protection OperatingMode (V8 Engines Only)Should an overheated engine condition exist and theREDUCED ENGINE POWER message is displayed, anoverheat protection mode which alternates firing groupsof cylinders helps prevent engine damage. In this mode,you will notice a loss in power and engine performance.This operating mode allows your vehicle to be driven toa safe place in an emergency. Towing a trailer in theoverheat protection mode should be avoided.

NOTICE:

After driving in the overheated engine protectionoperating mode, to avoid engine damage, allowthe engine to cool before attempting any repair.The engine oil will be severely degraded. Repairthe cause of coolant loss, change the oil and reset the oil life monitor. See “Engine Oil” in the Index.

yellowblue

5-10

If Steam Is Coming From Your EngineCAUTION:

Steam from an overheated engine can burn youbadly, even if you just open the hood. Stay awayfrom the engine if you see or hear steam comingfrom it. Just turn it off and get everyone awayfrom the vehicle until it cools down. Wait untilthere is no sign of steam or coolant before youopen the hood.

If you keep driving when your engine isoverheated, the liquids in it can catch fire. You orothers could be badly burned. Stop your engine ifit overheats, and get out of the vehicle until theengine is cool. See “Overheated EngineProtection Operating Mode” in the Index.

yellowblue

5-11

NOTICE:

If your engine catches fire because you keepdriving with no coolant, your vehicle can bebadly damaged. The costly repairs would not becovered by your warranty. See “OverheatedEngine Protection Operating Mode” in the Index.

If No Steam Is Coming From Your EngineIf you get an engine overheat warning but see or hear nosteam, the problem may not be too serious. Sometimesthe engine can get a little too hot when you:

� Climb a long hill on a hot day.

� Stop after high-speed driving.

� Idle for long periods in traffic.

� Tow a trailer. See “Driving on Grades” in the Index.

If you get the overheat warning with no sign of steam,try this for a minute or so:

1. If you have an air conditioner and it’s on, turn it off.

2. Turn on your heater to full hot at the highest fanspeed and open the window as necessary.

3. If you’re in a traffic jam, shift to NEUTRAL (N);otherwise, shift to the highest gear while driving -- DRIVE (D) for automatic transmissions.

If you no longer have the overheat warning, you candrive. Just to be safe, drive slower for about 10 minutes.If the warning doesn’t come back on, you can drive normally.

If the warning continues, pull over, stop, and park yourvehicle right away.

If there’s still no sign of steam, push down theaccelerator until the engine speed is about twice as fastas normal idle speed for at least three minutes whileyou’re parked. If you still have the warning, turn off theengine and get everyone out of the vehicle until it coolsdown. Also, see “Overheated Engine ProtectionOperating Mode” listed previously in this section.

You may decide not to lift the hood but to get servicehelp right away.

yellowblue

5-12

Cooling SystemWhen you decide it’s safe to lift the hood, here’s whatyou’ll see:

A. Coolant Surge Tank

B. Coolant Surge Tank Pressure Cap

C. Engine Fan

If the coolant inside the coolant surge tank is boiling,don’t do anything else until it cools down.

When the engine is cold, thecoolant level should be at orabove the FILL COLDmark. If it isn’t, you mayhave a leak in the radiatorhoses, heater hoses,radiator, water pump orsomewhere else in thecooling system.

yellowblue

5-13

CAUTION:

Heater and radiator hoses, and other engineparts, can be very hot. Don’t touch them. If youdo, you can be burned.

Don’t run the engine if there is a leak. If you runthe engine, it could lose all coolant. That couldcause an engine fire, and you could be burned.Get any leak fixed before you drive the vehicle.

NOTICE:

Engine damage from running your enginewithout coolant isn’t covered by your warranty.See “Overheated Engine Protection OperatingMode” in the Index.

NOTICE:

When adding coolant, it is important that you use only DEX-COOL� (silicate-free) coolant.If coolant other than DEX-COOL is added to the system, premature engine, heater core orradiator corrosion may result. In addition, theengine coolant will require change sooner -- at30,000 miles (50 000 km) or 24 months,whichever occurs first. Damage caused by the use of coolant other than DEX-COOL� is notcovered by your new vehicle warranty.

If there seems to be no leak, start the engine again. See if the engine cooling fan speed increases when idlespeed is doubled by pushing the accelerator pedal down.If it doesn’t, your vehicle needs service. Turn off the engine.

yellowblue

5-14

How to Add Coolant to the Coolant Surge TankIf you haven’t found a problem yet, but the coolant levelisn’t at or above the FILL COLD mark, add a 50/50mixture of clean, drinkable water and DEX-COOL�

coolant at the coolant surge tank, but be sure the coolingsystem, including the coolant surge tank pressure cap, iscool before you do it. (See “Engine Coolant” in theIndex for more information.)

CAUTION:

Steam and scalding liquids from a hot coolingsystem can blow out and burn you badly. They areunder pressure, and if you turn the coolant surgetank pressure cap -- even a little -- they can comeout at high speed. Never turn the cap when thecooling system, including the coolant surge tankpressure cap, is hot. Wait for the cooling systemand coolant surge tank pressure cap to cool if youever have to turn the pressure cap.

yellowblue

5-15

CAUTION:

Adding only plain water to your cooling systemcan be dangerous. Plain water, or some otherliquid like alcohol, can boil before the propercoolant mixture will. Your vehicle’s coolantwarning system is set for the proper coolantmixture. With plain water or the wrong mixture,your engine could get too hot but you wouldn’tget the overheat warning. Your engine couldcatch fire and you or others could be burned. Use a 50/50 mixture of clean, drinkable waterand DEX-COOL� coolant.

NOTICE:

In cold weather, water can freeze and crack theengine, radiator, heater core and other parts. So use the recommended coolant.

CAUTION:

You can be burned if you spill coolant on hotengine parts. Coolant contains ethylene glycoland it will burn if the engine parts are hotenough. Don’t spill coolant on a hot engine.

yellowblue

5-16

1. You can remove the coolant surge tank pressure capwhen the cooling system, including the coolant surge tank pressure cap and upper radiator hose, isno longer hot. Turn the pressure cap slowlycounterclockwise (left) about one full turn. If youhear a hiss, wait for that to stop. A hiss means thereis still some pressure left.

2. Then keep turning the pressure cap slowly, andremove it.

3. Then fill the coolant surge tank with the propermixture, to the FILL COLD mark.

yellowblue

5-17

4. With the coolant surge tank pressure cap off, start theengine and let it run until you can feel the upperradiator hose getting hot. Watch out for the enginecooling fan.

By this time, the coolant level inside the coolantsurge tank may be lower. If the level is lower, addmore of the proper mixture to the coolant surge tankuntil the level reaches the FILL COLD mark.

5. Then replace the pressure cap. Be sure the pressurecap is hand-tight.

yellowblue

5-18

Engine Fan NoiseYour vehicle has a clutched engine cooling fan. Whenthe clutch is engaged, the fan spins faster to providemore air to cool the engine. In most everyday drivingconditions, the fan is spinning slower and the clutch isnot fully engaged. This improves fuel economy andreduces fan noise. Under heavy vehicle loading, trailertowing and/or high outside temperatures, the fan speedincreases as the clutch more fully engages. So you mayhear an increase in fan noise. This is normal and shouldnot be mistaken as the transmission slipping or makingextra shifts. It is merely the cooling system functioningproperly. The fan will slow down when additionalcooling is not required and the clutch disengages.

You may also hear this fan noise when you start the engine. It will go away as the fan clutch partially disengages.

If a Tire Goes FlatIt’s unusual for a tire to “blow out” while you’re driving,especially if you maintain your tires properly. If air goesout of a tire, it’s much more likely to leak out slowly.But if you should ever have a “blowout,” here are a fewtips about what to expect and what to do:

If a front tire fails, the flat tire will create a drag thatpulls the vehicle toward that side. Take your foot off theaccelerator pedal and grip the steering wheel firmly.Steer to maintain lane position, and then gently brake toa stop well out of the traffic lane.

A rear blowout, particularly on a curve, acts much like askid and may require the same correction you’d use in askid. In any rear blowout, remove your foot from theaccelerator pedal. Get the vehicle under control bysteering the way you want the vehicle to go. It may bevery bumpy and noisy, but you can still steer. Gentlybrake to a stop -- well off the road if possible.

If a tire goes flat, the next part shows how to use yourjacking equipment to change a flat tire safely.

Changing a Flat TireIf a tire goes flat, avoid further tire and wheel damageby driving slowly to a level place. Turn on your hazardwarning flashers.

yellowblue

5-19

CAUTION:

Changing a tire can cause an injury. The vehiclecan slip off the jack and roll over you or otherpeople. You and they could be badly injured.Find a level place to change your tire. To helpprevent the vehicle from moving:

1. Set the parking brake firmly.2. Put an automatic transmission shift

lever in PARK (P) or shift a manualtransmission to FIRST (1) or REVERSE (R).

3. If you have a four-wheel-drive vehicle,be sure the transfer case is in a drivegear -- not in NEUTRAL (N).

4. Turn off the engine.5. Put the wheel blocks at the front and

rear of the tire farthest away from theone being changed. That would be thetire on the other side of the vehicle, atthe opposite end.

The following steps will tell you how to use the jack andchange a tire.

yellowblue

5-20

Removing the Spare Tire and Tools

Regular Cab

Extended Cab

yellowblue

5-21

The equipment you’ll need is behind the passenger’s seat.

1. If there is a cover, move the seats forward and turnthe wing nut on the cover counterclockwise toremove it.

2. The wheel blocks and the wheel block retainer can be removed by turning the wing nut counterclockwise.

3. To release the bottle jack from it’s holder, turn theknob on the bottle jack counterclockwise to lowerthe jack head slightly.

4. There is also a wing nut used to retain the storagebag and tools. To remove it, turn the wing nut counterclockwise.

You’ll use the jack handle and the wheel wrench toremove the underbody-mounted spare tire. A. Hoist Assembly

B. Wheel Wrench

C. Extensions

D. Hoist Shaft

E. Valve Stem, Pointed Down

F. Spare Tire

G. Tire Retainer

H. Hoist Cable

I. Hoist Lock

J. Hoist Shaft Access Hole

K. Hoist End

yellowblue

5-22

Follow these instructions to lower the spare tire:

1. If the vehicle is equipped with a hoist lock, open thespare tire lock cover on the bumper and use theignition key to remove the lock.

2. Assemble the wheel wrench and the two jack handleextensions as shown. Insert the hoist end (open end)of the extension through the hole in the rear bumper.Be sure the hoist end of the extension connects intothe hoist shaft.

3. Turn the wheel wrench counterclockwise to lowerthe spare tire to the ground. Continue to turn thewheel wrench until the spare tire can be pulled outfrom under the vehicle. The wheel wrench has ahook that allows you to pull the hoist cable towardsyou, to assist in reaching the spare tire.

4. When the tire has been lowered, tilt the retainer atthe end of the cable so it can be pulled up throughthe wheel opening.

5. Put the spare tire near the flat tire.

The tools you’ll be using include the bottle jack (A), thewheel blocks (B), the jack handle (C), the jack handleextensions (D), and the wheel wrench (E).

If the flat tire is on the rear of the vehicle, you’ll need touse both jack handle extensions.

yellowblue

5-23

Attach the wheel wrench to the jack handle extensions(as needed). Attach the jack handle to the jack.

Turn the wheel wrench clockwise to raise the jack lifthead a little.

yellowblue

5-24

If your vehicle has wheelnut caps, loosen them byturning the wheel wrenchcounterclockwise. If youhave a center cap withwheel nut caps, the wheelnut caps are designed toremain with the center cap.

Remove the center cap.

If the wheel has a smooth center piece, place the chiselend of the wheel wrench in the slot on the wheel andgently pry out.

Removing the Flat Tire and Installing theSpare Tire

1. Use the wheel wrench toloosen all the wheelnuts. Turn the wheel wrenchcounterclockwise toloosen the wheel nuts.Don’t remove the wheelnuts yet.

yellowblue

5-25

2. Position the jack under the vehicle. If the flat tire is on the front of the vehicle (2-Wheel Drive 1500 Series vehicles), position the jack under thebracket attached to the vehicle’s frame, behind theflat tire. If the flat tire is on the front of the vehicle(All other models), position the jack on the framebehind the flat tire.

If the flat tire is on the rear, position the jack underthe rear axle between the spring anchor and theshock absorber bracket.

If you have added a snow plow to the front of yourvehicle, lower the snow plow fully before raising the vehicle.

CAUTION:

Getting under a vehicle when it is jacked up isdangerous. If the vehicle slips off the jack, youcould be badly injured or killed. Never get undera vehicle when it is supported only by a jack.

CAUTION:

Raising your vehicle with the jack improperlypositioned can damage the vehicle and even makethe vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lifthead into the proper location before raising the vehicle.

yellowblue

5-26

Front Position 2WD 1500 Series

Front Position All Other Models

yellowblue

5-27

Rear Position

3. Make sure the jack head is positioned so that the rearaxle is resting securely between the grooves that areon the jack head. Turn the wheel wrench clockwiseto raise the vehicle. Raise the vehicle far enough offthe ground so there is enough room for the spare tireto fit.

4. Remove all the wheelnuts and take off the flat tire.

5. Remove any rust or dirtfrom the wheel bolts,mounting surfaces andspare wheel.

yellowblue

5-28

CAUTION:

Rust or dirt on the wheel, or on the parts towhich it is fastened, can make the wheel nutsbecome loose after a time. The wheel could comeoff and cause an accident. When you change awheel, remove any rust or dirt from the placeswhere the wheel attaches to the vehicle. In anemergency, you can use a cloth or a paper towelto do this; but be sure to use a scraper or wirebrush later, if you need to, to get all the rust ordirt off.

CAUTION:

Never use oil or grease on studs or nuts. If youdo, the nuts might come loose. Your wheel couldfall off, causing a serious accident.

6. After mounting thespare, replace the wheelnuts with the roundedend of the nuts towardthe wheel. Tighten eachwheel nut by hand usingthe wheel wrench untilthe wheel is held againstthe hub.

yellowblue

5-29

Front Position 2WD 1500 Series Front Position All Other Models

yellowblue

5-30

Rear Position

7. Turn the wheel wrench counterclockwise to lowerthe vehicle. Lower the jack completely.

8. Tighten the nuts firmly in a crisscross sequence asshown by turning the wheel wrench clockwise.

yellowblue

5-31

CAUTION:

Incorrect wheel nuts or improperly tightenedwheel nuts can cause the wheel to become looseand even come off. This could lead to an accident.Be sure to use the correct wheel nuts. If you haveto replace them, be sure to get new GM originalequipment wheel nuts.Stop somewhere as soon as you can and have thenuts tightened with a torque wrench to theproper torque. See “Capacities andSpecifications” in the Index.

NOTICE:

Improperly tightened wheel nuts can lead tobrake pulsation and rotor damage. To avoidexpensive brake repairs, evenly tighten the wheelnuts in the proper sequence and to the propertorque specification.

Storing a Flat or Spare Tire and Tools

CAUTION:

Storing a jack, a tire or other equipment in thepassenger compartment of the vehicle couldcause injury. In a sudden stop or collision, looseequipment could strike someone. Store all thesein the proper place.

Return the bottle jack, wheel blocks, wheel wrench andjack extensions to their location behind the passenger’sseat. Secure the items in the vehicle as shown.

yellowblue

5-32

A. Wing Nut

B. Wheel Blocks

C. Wheel Wrench andExtensions Retainer

D. Gloves

E. Wheel Wrench andExtensions

F. Storage Bag

G. Bottle Jack Holder

H. Bottle Jack

I. Wheel BlockRetainer

Store the flat tire where the spare tire was stored.

Store the tire under the rear of the vehicle in the sparetire carrier. To store the tire:

1. Put the tire on the ground at the rear of the vehiclewith the valve stem pointed downward and to the rear.

2. Tilt the retainer downward and through the wheelopening. Make sure that the retainer is fully seatedacross the underside of the wheel.

3. Attach the wheel wrench and extensions together.Insert the hoist end through the hole in the rearbumper and into the hoist shaft.

4. Raise the tire part of the way upward. When the tireis almost in the stored position, adjust the tire so thatthe valve stem is toward the rear of the vehicle.

yellowblue

5-33

A. Hoist Assembly

B. Wheel Wrench

C. Extensions

D. Hoist Shaft

E. Valve Stem, Pointed Down

F. Flat or Spare Tire

G. Retainer

H. Hoist Cable

5. Raise the tire fully against the underside of thevehicle. Continue turning the wheel wrench until thetire is secure and the cable is tight. The spare tirehoist cannot be overtightened.

6. Make sure the tire is stored securely. Push, pull, andthen try to rotate or turn the tire. If the tire moves,use the wheel wrench/hoist shaft to tighten the cable.

Replace the jack, tools and spare tire lock.

yellowblue

5-34

If You’re Stuck: In Sand, Mud, Ice or SnowIn order to free your vehicle when it is stuck, you willneed to spin the wheels, but you don’t want to spin yourwheels too fast. The method known as “rocking” canhelp you get out when you’re stuck, but you must use caution.

CAUTION:

If you let your tires spin at high speed, they canexplode, and you or others could be injured. And, the transmission or other parts of thevehicle can overheat. That could cause an enginecompartment fire or other damage. When you’restuck, spin the wheels as little as possible. Don’tspin the wheels above 35 mph (55 km/h) as shownon the speedometer.

NOTICE:

Spinning your wheels can destroy parts of yourvehicle as well as the tires. If you spin the wheelstoo fast while shifting your transmission backand forth, you can destroy your transmission.

For information about using tire chains on your vehicle,see “Tire Chains” in the Index.

yellowblue

5-35

Rocking Your Vehicle To Get It OutFirst, turn your steering wheel left and right. That willclear the area around your front wheels. If you have afour-wheel drive vehicle, shift into 4HI. Then shift backand forth between REVERSE (R) and a forward gear (or with a manual transmission, between FIRST (1) orSECOND (2) and REVERSE (R)), spinning the wheelsas little as possible. Release the accelerator pedal whileyou shift, and press lightly on the accelerator pedalwhen the transmission is in gear. By slowly spinningyour wheels in the forward and reverse directions, youwill cause a rocking motion that may free your vehicle.If that doesn’t get you out after a few tries, you mayneed to be towed out. Or, you can use your recoveryhooks if your vehicle has them. If you do need to betowed out, see “Towing Your Vehicle” in the Index.

Using the Recovery Hooks

Your vehicle may be equipped with recovery hooks. The recovery hooks are provided at the front of yourvehicle. You may need to use them if you’re stuckoff-road and need to be pulled to some place where youcan continue driving.

yellowblue

5-36

CAUTION:

The recovery hooks, when used, are under a lot offorce. Always pull the vehicle straight out. Neverpull on the hooks at a sideways angle. The hookscould break off and you or others could beinjured from the chain or cable snapping back.

NOTICE:

Never use the recovery hooks to tow the vehicle.Your vehicle could be damaged and it would notbe covered by warranty.

6-

yellowblue

6-1

Section 6 Service and Appearance Care

Here you will find information about the care of your vehicle. This section begins with service and fuel information,and then it shows how to check important fluid and lubricant levels. There is also technical information about yourvehicle, and a part devoted to its appearance care.

6-2 Service6-3 Fuel6-5 Fuels in Foreign Countries6-6 Filling Your Tank6-8 Checking Things Under the Hood6-12 Engine Oil6-16 Engine Air Cleaner/Filter6-19 Automatic Transmission Fluid6-23 Manual Transmission Fluid6-24 Hydraulic Clutch6-25 Rear Axle6-26 Four-Wheel Drive6-28 Engine Coolant6-31 Coolant Surge Tank Pressure Cap6-32 Power Steering Fluid

6-33 Windshield Washer Fluid6-34 Brakes6-38 Battery6-38 Bulb Replacement6-44 Windshield Wiper Blade Replacement6-45 Tires6-53 Appearance Care6-54 Cleaning the Inside of Your Vehicle6-57 Cleaning the Outside of Your Vehicle6-61 GM Vehicle Care/Appearance Materials6-62 Vehicle Identification Number (VIN)6-63 Electrical System6-71 Replacement Bulbs6-72 Capacities and Specifications

yellowblue

6-2

ServiceYour dealer knows your vehicle best and wants you tobe happy with it. We hope you’ll go to your dealer forall your service needs. You’ll get genuine GM parts andGM-trained and supported service people.

We hope you’ll want to keep your GM vehicle all GM.Genuine GM parts have one of these marks:

Doing Your Own Service WorkIf you want to do some of your own service work, you’llwant to use the proper service manual. It tells you muchmore about how to service your vehicle than this manualcan. To order the proper service manual, see “Serviceand Owner Publications” in the Index.

Your vehicle may have an air bag system. If it does, see“Servicing Your Air Bag-Equipped Vehicle” in theIndex before attempting to do your own service work.

You should keep a record with all parts receipts and listthe mileage and the date of any service work youperform. See “Maintenance Record” in the Index.

yellowblue

6-3

CAUTION:

You can be injured and your vehicle could bedamaged if you try to do service work on avehicle without knowing enough about it.

� Be sure you have sufficient knowledge,experience, the proper replacement partsand tools before you attempt any vehiclemaintenance task.

� Be sure to use the proper nuts, bolts andother fasteners. “English” and “metric”fasteners can be easily confused. If you usethe wrong fasteners, parts can later breakor fall off. You could be hurt.

Adding Equipment to the Outside of Your VehicleThings you might add to the outside of your vehicle canaffect the airflow around it. This may cause wind noiseand affect windshield washer performance. Check withyour dealer before adding equipment to the outside ofyour vehicle.

FuelUse regular unleaded gasoline rated at 87 octane orhigher. It is recommended that the gasoline meetspecifications which have been developed by theAmerican Automobile Manufacturers Association(AAMA) and endorsed by the Canadian Motor VehicleManufacturers Association for better vehicleperformance and engine protection. Gasolines meetingthe AAMA specification could provide improveddriveability and emission control system performancecompared to other gasolines.

Be sure the posted octane is at least 87. If the octane isless than 87, you may get a heavy knocking noise whenyou drive. If it’s bad enough, it can damage your engine.

If you’re using fuel rated at 87 octane or higher and youhear heavy knocking, your engine needs service. Butdon’t worry if you hear a little pinging noise whenyou’re accelerating or driving up a hill. That’s normal,and you don’t have to buy a higher octane fuel to get ridof pinging. It’s the heavy, constant knock that meansyou have a problem.

yellowblue

6-4

If your vehicle is certified to meet California EmissionStandards (indicated on the underhood emission controllabel), it is designed to operate on fuels that meetCalifornia specifications. If such fuels are not availablein states adopting California emissions standards, yourvehicle will operate satisfactorily on fuels meetingfederal specifications, but emission control systemperformance may be affected. The malfunction indicatorlamp on your instrument panel may turn on and/or yourvehicle may fail a smog-check test. (See “MalfunctionIndicator Lamp” in the Index.) If this occurs, return toyour authorized GM dealer for diagnosis to determinethe cause of failure. In the event it is determined that thecause of the condition is the type of fuels used, repairsmay not be covered by your warranty.

Some gasolines that are not reformulated for lowemissions may contain an octane-enhancing additivecalled methylcyclopentadienyl manganese tricarbonyl(MMT); ask your service station operator whether or notthe fuel contains MMT. General Motors does notrecommend the use of such gasolines. If fuels containingMMT are used, spark plug life may be reduced and youremission control system performance may be affected.The malfunction indicator lamp on your instrumentpanel may turn on. If this occurs, return to yourauthorized GM dealer for service.

yellowblue

6-5

To provide cleaner air, all gasolines in the United Statesare now required to contain additives that will helpprevent deposits from forming in your engine and fuelsystem, allowing your emission control system tofunction properly. Therefore, you should not have to addanything to the fuel. In addition, gasolines containingoxygenates, such as ethers and ethanol, andreformulated gasolines may be available in your area tocontribute to clean air. General Motors recommends thatyou use these gasolines, particularly if they comply withthe specifications described earlier.

NOTICE:

Your vehicle was not designed for fuel thatcontains methanol. Don’t use it. It can corrodemetal parts in your fuel system and also damageplastic and rubber parts. That damage wouldn’tbe covered under your warranty.

Fuels in Foreign CountriesIf you plan on driving in another country outside theUnited States or Canada, the proper fuel may be hard tofind. Never use leaded gasoline or any other fuel notrecommended in the previous text on fuel. Costly repairscaused by use of improper fuel wouldn’t be covered byyour warranty.

To check on fuel availability, ask an auto club, orcontact a major oil company that does business in thecountry where you’ll be driving.

You can also write us at the following address foradvice. Just tell us where you’re going and give yourVehicle Identification Number (VIN).

General Motors Overseas Distribution Corporation1908 Colonel Sam DriveOshawa, Ontario L1H 8P7

yellowblue

6-6

Filling Your Tank

CAUTION:

Gasoline vapor is highly flammable. It burnsviolently, and that can cause very bad injuries.Don’t smoke if you’re near gasoline or refuelingyour vehicle. Keep sparks, flames and smokingmaterials away from gasoline.

While refueling, hang the filler cap by the tether usingthe hook located on the inside of the filler door.

To remove the cap, turn it slowly to the left(counterclockwise).

yellowblue

6-7

CAUTION:

If you get gasoline on yourself and thensomething ignites it, you could be badly burned.Gasoline can spray out on you if you open thefuel filler cap too quickly. This spray can happenif your tank is nearly full, and is more likely inhot weather. Open the fuel filler cap slowly andwait for any “hiss” noise to stop. Then unscrewthe cap all the way.

Be careful not to spill gasoline. Clean gasoline frompainted surfaces as soon as possible. See “Cleaning theOutside of Your Vehicle” in the Index.

When you put the cap back on, turn it to the right(clockwise) until you hear a clicking sound. Make sureyou fully install the cap. The diagnostic system candetermine if the fuel cap has been left off or improperlyinstalled. This would allow fuel to evaporate into theatmosphere. See “Malfunction Indicator Lamp” in the Index.

NOTICE:

If you need a new cap, be sure to get the righttype. Your dealer can get one for you. If you getthe wrong type, it may not fit properly. This maycause your malfunction indicator lamp to lightand your fuel tank and emissions system may bedamaged. See “Malfunction Indicator Lamp” inthe Index.

yellowblue

6-8

Filling a Portable Fuel Container

CAUTION:

Never fill a portable fuel container while it is inyour vehicle. Static electricity discharge from thecontainer can ignite the gasoline vapor. You canbe badly burned and your vehicle damaged if thisoccurs. To help avoid injury to you and others:

� Dispense gasoline only into approved containers.

� Do not fill a container while it is inside avehicle, in a vehicle’s trunk, pickup bed oron any surface other than the ground.

� Bring the fill nozzle in contact with theinside of the fill opening before operatingthe nozzle. Contact should be maintaineduntil the filling is complete.

� Don’t smoke while pumping gasoline.

Checking Things Under the Hood

CAUTION:

Things that burn can get on hot engine parts andstart a fire. These include liquids like fuel, oil,coolant, brake fluid, windshield washer and otherfluids, and plastic or rubber. You or others couldbe burned. Be careful not to drop or spill thingsthat will burn onto a hot engine.

yellowblue

6-9

Hood Release

To open the hood, first pullthe handle inside the vehicle.

Then go to the front of the vehicle and pull up on thesecondary hood release, located just to the passenger’sside of the center of the grill.

Lift the hood.

Before closing the hood, be sure all filler caps are onproperly. Pull down the hood and close it firmly.

yellowblue

6-10

VORTEC 4300 V6 EngineWhen you lift up the hood you’ll see:

A. Engine Air Cleaner/FilterB. Coolant Surge TankC. Air Filter Restriction IndicatorD. Engine Oil DipstickE. Automatic Transmission Dipstick

(If Equipped)

F. FanG. Engine Oil FillH. Power Steering Fluid ReservoirI. Remote Negative Terminal (GND)J. Remote Positive TerminalK. Brake Fluid Reservoir

L. Clutch Fluid Reservoir (If Equipped)

M. Underhood Electrical CenterN. BatteryO. Windshield Washer Fluid

Reservoir

yellowblue

6-11

VORTEC 4800, 5300 and 6000 V8 EngineVORTEC 5300 V8 engine shown, locations for other engines similar.

A. Engine Air Cleaner/FilterB. Coolant Surge TankC. Air Filter Restriction IndicatorD. Engine Oil DipstickE. Automatic Transmission

Dipstick (If Equipped)

F. Engine Oil FillG. FanH. Remote Negative Terminal (GND)I. Power Steering Fluid ReservoirJ. Remote Positive TerminalK. Brake Fluid Reservoir

L. Clutch Fluid Reservoir (If Equipped)

M. Underhood Electrical CenterN. BatteryO. Windshield Washer Fluid

Reservoir

yellowblue

6-12

Engine OilIf the CHECK ENG OILLEVEL appears on theinstrument panel, it meansyou need to check yourengine oil level right away.

For more information, see “CHECK ENG OIL LEVEL”in the Index.

You should check your engine oil level regularly; this isan added reminder.

Checking Engine OilIt’s a good idea to check your engine oil every time youget fuel. In order to get an accurate reading, the oil mustbe warm and the vehicle must be on level ground.

The engine oil dipstick hasa yellow ring handle and islocated on the passenger’sside of the engine.

Turn off the engine and give the oil several minutes todrain back into the oil pan. If you don’t, the oil dipstickmight not show the actual level.

Pull out the dipstick and clean it with a paper towel orcloth, then push it back in all the way. Remove it again,keeping the tip down, and check the level.

yellowblue

6-13

When to Add Engine OilIf the oil is at or below the ADD mark, then you’ll needto add at least one quart of oil. But you must use theright kind. This part explains what kind of oil to use. Forcrankcase capacity, see “Capacities and Specifications”in the Index.

NOTICE:

Don’t add too much oil. If your engine has somuch oil that the oil level gets above thecross-hatched area that shows the properoperating range, your engine could be damaged.

The engine oil fill cap forthe VORTEC 4300 V6engine is located on thedriver’s side engine valve cover.

The engine oil fill cap for the VORTEC 4800, 5300 and6000 V8 engines is located on the passenger’s sideengine valve cover.

Be sure to fill it enough to put the level somewhere inthe proper operating range. Push the dipstick all the wayback in when you’re through.

yellowblue

6-14

What Kind of Engine Oil to UseOils recommended for your vehicle can be identified bylooking for the starburst symbol.

This symbol indicates that the oil has been certified bythe American Petroleum Institute (API). Do not use anyoil which does not carry this starburst symbol.

If you change your own oil, be sure you use oil that hasthe starburst symbol on the front of the oil container. Ifyou have your oil changed for you, be sure the oil putinto your engine is American Petroleum Institutecertified for gasoline engines.

You should also use the proper viscosity oil for yourvehicle, as shown in the following chart:

yellowblue

6-15

As shown in the chart, SAE 5W-30 is best for yourvehicle. However, you can use SAE 10W-30 if it’s goingto be 0�F (-18�C) or above. These numbers on an oilcontainer show its viscosity, or thickness. Do not useother viscosity oils, such as SAE 20W-50.

NOTICE:

Use only engine oil with the American PetroleumInstitute Certified For Gasoline Enginesstarburst symbol. Failure to use therecommended oil can result in engine damage notcovered by your warranty.

GM Goodwrench� oil meets all the requirements foryour vehicle.

If you are in an area where the temperature falls below-20�F (-29�C), consider using either an SAE 5W-30synthetic oil or an SAE 0W-30 oil. Both will provideeasier cold starting and better protection for your engineat extremely low temperatures.

Engine Oil AdditivesDon’t add anything to your oil. The recommended oilswith the starburst symbol are all you will need for goodperformance and engine protection.

When to Change Engine OilYour vehicle has a computer that lets you know when tochange your engine oil. This is not based on mileage,but on engine revolutions and engine operatingtemperature. When the computer has calculated that theoil needs changing, the GM Oil Life System� willindicate that a change is necessary. The mileage betweenoil and filter changes will vary depending on how youdrive your vehicle -- usually between 3,000 miles (5 000 km) and 7,500 miles (12 500 km) since your lastoil and filter change. Under severe conditions, thesystem may come on before 3,000 miles (5 000 km).Never drive your vehicle more than 7,500 miles (12 500 km) or 12 months (whichever occurs first)without an oil change.

The system won’t detect dust in the oil. So, if you drivein a dusty area, be sure to change your oil and filterevery 3,000 miles (5 000 km) or sooner. Remember toreset the CHANGE ENGINE OIL message wheneverthe oil is changed.

yellowblue

6-16

How to Reset the CHANGE ENGINE OIL Message

To reset the CHANGE ENGINE OIL message, turn theignition key to RUN with the engine off. Fully press andrelease the accelerator pedal three times within fiveseconds. If the CHANGE ENGINE OIL message flashesfor five seconds, the system is reset.

What to Do with Used OilDid you know that used engine oil contains certainelements that may be unhealthy for your skin and couldeven cause cancer? Don’t let used oil stay on your skinfor very long. Clean your skin and nails with soap andwater, or a good hand cleaner. Wash or properly throwaway clothing or rags containing used engine oil. (Seethe manufacturer’s warnings about the use and disposalof oil products.)

Used oil can be a real threat to the environment. If youchange your own oil, be sure to drain all free-flowing oilfrom the filter before disposal. Don’t ever dispose of oilby putting it in the trash, pouring it on the ground, intosewers, or into streams or bodies of water. Instead,recycle it by taking it to a place that collects used oil. Ifyou have a problem properly disposing of your used oil,ask your dealer, a service station or a local recyclingcenter for help.

Engine Air Cleaner/FilterThe air cleaner assemblyhas an indicator that letsyou know when the air filteris dirty and needs to beserviced. The indicator islocated on the air cleaner cover.

See “Owner Checks and Services” in the Index todetermine when to check the indicator.

If the area inside the clear section of the indicator is notcompletely yellow, no air filter service is required.When the area inside the indicator is completely yellow,past the red band, the words “CHANGE FILTER” willbe highlighted. After changing the air filter, press the topbutton on the indicator to reset it.

yellowblue

6-17

Your air cleaner is located in the passenger’s side frontcorner of the engine compartment.

1. To remove the air filter, loosen the screws on thecover. Lift the cover upward. Lift the filter out of theair cleaner housing. Care should be taken to dislodgeas little dirt as possible.

2. Clean the filter sealing surface and the filter housing.

3. Install the new filter.

4. Install the cover and tighten the screws on the aircleaner cover.

Refer to the Maintenance Schedule to determine when toreplace the air filter. See “Owner Checks and Services”in the Index.

yellowblue

6-18

CAUTION:

Operating the engine with the air cleaner/filteroff can cause you or others to be burned. The aircleaner not only cleans the air, it stops flame ifthe engine backfires. If it isn’t there, and theengine backfires, you could be burned. Don’tdrive with it off, and be careful working on theengine with the air cleaner/filter off.

NOTICE:

If the air cleaner/filter is off, a backfire can causea damaging engine fire. And, dirt can easily getinto your engine, which will damage it. Alwayshave the air cleaner/filter in place when you’re driving.

Passenger Compartment Air Filter(If Equipped)Your vehicle may be equipped with a passengercompartment air filter. The filter is located under theinstrument panel below the glove compartment.

To replace the passenger compartment air filter:

1. If your vehicle is equipped with a panel under thecenter of the instrument panel, remove the bolts on itto remove the panel. Because this operation can be alittle difficult, you may choose to have it done atyour dealer service department.

yellowblue

6-19

2. If your vehicle does nothave a panel under thecenter of the instrumentpanel, or when the panelis removed, reach underthe instrument paneltowards the front of thevehicle and pulldownward on the filterretaining bracket.

3. Remove the air filter by pulling downward on theelement. Remove the second portion of the air filterby sliding it towards the rear of the vehicle and thenpulling downward.

4. Install the new filter by reversing the steps listedpreviously. Be sure to follow any instructions thatmay be included in the replacement filter package.

Refer to the Maintenance Schedule to determine when toreplace the passenger compartment air filter. See“Scheduled Maintenance” in the Index.

Automatic Transmission FluidWhen to Check and ChangeA good time to check your automatic transmission fluidlevel is when the engine oil is changed.

Change both the fluid and filter every 50,000 miles (83 000 km) if the vehicle is mainly driven under one ormore of these conditions:

� In heavy city traffic where the outside temperatureregularly reaches 90�F (32�C) or higher.

� In hilly or mountainous terrain.

� When doing frequent trailer towing.

� Uses such as found in taxi, police or delivery service.

If you do not use your vehicle under any of theseconditions, change the fluid and filter every 100,000 miles (166 000 km).

See “Scheduled Maintenance Services” in the Index.

yellowblue

6-20

How to CheckBecause this operation can be a little difficult, you may choose to have this done at the dealership service department.

If you do it yourself, be sure to follow all theinstructions here, or you could get a false reading on the dipstick.

NOTICE:

Too much or too little fluid can damage yourtransmission. Too much can mean that some ofthe fluid could come out and fall on hot engineparts or exhaust system parts, starting a fire. Besure to get an accurate reading if you check yourtransmission fluid.

Wait at least 30 minutes before checking thetransmission fluid level if you have been driving:

� When outside temperatures are above 90�F (32�C).

� At high speed for quite a while.

� In heavy traffic -- especially in hot weather.

� While pulling a trailer.

To get the right reading, the fluid should be at normaloperating temperature, which is 180�F to 200�F (82�C to 93�C).

Get the vehicle warmed up by driving about 15 miles(24 km) when outside temperatures are above 50�F(10�C). If it’s colder than 50�F (10�C), drive thevehicle in THIRD (3) until the engine temperature gagemoves and then remains steady for 10 minutes. Thenfollow the hot check procedures.

yellowblue

6-21

Checking Transmission Fluid Cold

A cold check is made after the vehicle has been sittingfor eight hours or more with the engine off and is usedonly as a reference. Let the engine run at idle for fiveminutes if outside temperatures are 50�F (10�C) ormore. If it’s colder than 50�F (10�C), you may have toidle the engine longer. Should the fluid level be lowduring a cold check, you must perform a hot checkbefore adding fluid. This will give you a more accuratereading of the fluid level.

Checking the Fluid Level

Prepare your vehicle as follows:

� Park your vehicle on a level place. Keep the engine running.

� With the parking brake applied, place the shift leverin PARK (P).

� With your foot on the brake pedal, move the shiftlever through each gear range, pausing for aboutthree seconds in each range. Then, position the shiftlever in PARK (P).

� Let the engine run at idle for three minutes or more.

Then, without shutting off the engine, follow these steps:

1. The red transmission dipstick handle is located at therear of the engine compartment, on the passenger’sside. Flip the handle up and then pull out the dipstickand wipe it with a clean rag or paper towel.

2. Push it back in all the way, wait three seconds andthen pull it back out again.

yellowblue

6-22

3. Check both sides of the dipstick, and read the lowerlevel. The fluid level must be in the COLD area,below the cross-hatched area, for a cold check or inthe HOT area or cross-hatched area for a hot check.

4. If the fluid level is in the acceptable range, push thedipstick back in all the way; then flip the handledown to lock the dipstick in place.

How to Add FluidRefer to the Maintenance Schedule to determine whatkind of transmission fluid to use. See “RecommendedFluids and Lubricants” in the Index.

Add fluid only after checking the transmission fluidwhile it is hot. (A cold check is used only as areference.) If the fluid level is low, add only enough ofthe proper fluid to bring the level up to the HOT area fora hot check. It doesn’t take much fluid, generally lessthan one pint (0.5 L). Don’t overfill.

NOTICE:

We recommend you use only fluid labeledDEXRON�-III, because fluid with that label ismade especially for your automatic transmission.Damage caused by fluid other than DEXRON�-IIIis not covered by your new vehicle warranty.

� After adding fluid, recheck the fluid level asdescribed under “How to Check.”

� When the correct fluid level is obtained, push thedipstick back in all the way; then flip the handledown to lock the dipstick in place.

yellowblue

6-23

Manual Transmission FluidWhen to CheckA good time to have it checked is when the engine oil ischanged. See your maintenance schedule to find outwhen to change your transmission fluid.

How to CheckBecause this operation can be a little difficult, you maychoose to have this done at your GM dealership service department.

If you do it yourself, be sure to follow all theinstructions here, or you could get a false reading.

NOTICE:

Too much or too little fluid can damage yourtransmission. Too much can mean that some ofthe fluid could come out and fall on hot engineparts or exhaust system parts, starting a fire. Besure to get an accurate reading if you check yourtransmission fluid.

Check the fluid level only when your engine is off, thevehicle is parked on a level place and the transmission iscool enough for you to rest your fingers on thetransmission case.

yellowblue

6-24

Then, follow these steps:

5-Speed for VORTEC 4300 V6 and 4800 V8 enginesshown, other manual transmissions similar

1. Remove the filler plug.

2. Check that the lubricant level is up to the bottom ofthe filler plug hole.

3. If the fluid level is good, install the plug and be sureit is fully seated. If the fluid level is low, add morefluid as described in the next steps.

How to Add FluidHere’s how to add fluid. Refer to the MaintenanceSchedule to determine what kind of fluid to use. See“Recommended Fluids and Lubricants” in the Index.

1. Remove the filler plug.

2. Add fluid at the filler plug hole. Add only enoughfluid to bring the fluid level up to the bottom of thefiller plug hole.

3. Install the filler plug. Be sure the plug is fully seated.

Hydraulic ClutchThe hydraulic clutch linkage in your vehicle isself-adjusting. The clutch master cylinder reservoir isfilled with hydraulic clutch fluid.

It is not necessary to regularly check clutch fluid unlessyou suspect there is a leak in the system. Adding fluidwon’t correct a leak.

A fluid loss in this system could indicate a problem.Have the system inspected and repaired.

yellowblue

6-25

When to Check and What to Use

Refer to the MaintenanceSchedule to determine howoften you should check thefluid level in your clutchmaster cylinder reservoirand for the proper fluid.

See “Owner Checks and Services” and “RecommendedFluids and Lubricants” in the Index.

How to Check and Add FluidThe proper fluid should be added if the level does notreach the bottom of the diaphragm when it’s in place inthe reservoir. See the instructions on the reservoir cap.

Rear AxleWhen to Check LubricantRefer to the Maintenance Schedule to determine howoften to check the lubricant. See “ScheduledMaintenance Services” in the Index.

How to Check Lubricant

1500 Series shown, 2500 Series similar

yellowblue

6-26

The proper level for the 1500 Series is from 5/8 inch to1 5/8 inch (15 mm to 40 mm) below the filler plug. Theproper level for the 2500 Series is from 0 to 3/8 inch (0 to 10 mm) below the filler plug. Add only enoughfluid to reach the proper level.

What to UseRefer to the Maintenance Schedule to determine whatkind of lubricant to use. See “Recommended Fluids andLubricants” in the Index.

Four-Wheel DriveMost lubricant checks in this section also apply tofour-wheel-drive vehicles. However, they have twoadditional systems that need lubrication.

Transfer Case

When to Check Lubricant

Refer to the Maintenance Schedule to determine howoften to check the lubricant. See “Periodic MaintenanceInspections” in the Index.

How to Check Lubricant

Manual Transfer Case

yellowblue

6-27

Automatic Transfer Case

If the level is below the bottom of the filler plug hole,you’ll need to add some lubricant. Add enough lubricantto raise the level to the bottom of the filler plug hole.Use care not to overtighten plug.

What to Use

Refer to the Maintenance Schedule to determine whatkind of lubricant to use. See “Recommended Fluids andLubricants” in the Index.

Front Axle

When to Check Lubricant

Refer to the Maintenance Schedule to determine howoften to check the lubricant. See “ScheduledMaintenance Services” in the Index.

How to Check Lubricant

If the level is below the bottom of the filler plug hole,you may need to add some lubricant.

yellowblue

6-28

When the differential is cold, add enough lubricant toraise the level to 1/2 inch (12 mm) below the filler plug hole.

When the differential is at operating temperature(warm), add enough lubricant to raise the level to thebottom of the filler plug hole.

What to Use

Refer to the Maintenance Schedule to determine whatkind of lubricant to use. See “Recommended Fluids andLubricants” in the Index.

Engine CoolantThe cooling system in your vehicle is filled withDEX-COOL� engine coolant. This coolant is designedto remain in your vehicle for 5 years or 150,000 miles(240 000 km), whichever occurs first, if you add onlyDEX-COOL� extended life coolant.

The following explains your cooling system and how toadd coolant when it is low. If you have a problem withengine overheating, see “Engine Overheating” in the Index.

A 50/50 mixture of clean, drinkable water andDEX-COOL� coolant will:

� Give freezing protection down to -34�F (-37�C).

� Give boiling protection up to 265�F (129�C).

� Protect against rust and corrosion.

� Help keep the proper engine temperature.

� Let the warning lights and gages work as they should.

NOTICE:

When adding coolant, it is important that you use only DEX-COOL� (silicate-free) coolant.If coolant other than DEX-COOL is added to the system, premature engine, heater core orradiator corrosion may result. In addition, theengine coolant will require change sooner -- at30,000 miles (50 000 km) or 24 months,whichever occurs first. Damage caused by the use of coolant other than DEX-COOL� is notcovered by your new vehicle warranty.

yellowblue

6-29

What to UseUse a mixture of one-half clean, drinkable water andone-half DEX-COOL� coolant which won’t damagealuminum parts. If you use this coolant mixture, youdon’t need to add anything else.

CAUTION:

Adding only plain water to your cooling systemcan be dangerous. Plain water, or some otherliquid like alcohol, can boil before the propercoolant mixture will. Your vehicle’s coolantwarning system is set for the proper coolantmixture. With plain water or the wrong mixture,your engine could get too hot but you wouldn’tget the overheat warning. Your engine couldcatch fire and you or others could be burned. Use a 50/50 mixture of clean, drinkable waterand DEX-COOL� coolant.

NOTICE:

If you use an improper coolant mixture, yourengine could overheat and be badly damaged.The repair cost wouldn’t be covered by yourwarranty. Too much water in the mixture canfreeze and crack the engine, radiator, heater coreand other parts.

If you have to add coolant more than four times a year,have your dealer check your cooling system.

NOTICE:

If you use the proper coolant, you don’t have toadd extra inhibitors or additives which claim toimprove the system. These can be harmful.

yellowblue

6-30

Checking Coolant

The coolant surge tank is located on the passenger’s side of theengine compartment.

CAUTION:

Turning the surge tank pressure cap when theengine and radiator are hot can allow steam andscalding liquids to blow out and burn you badly.Never turn the surge tank pressure cap -- even alittle -- when the engine and radiator are hot.

The vehicle must be on a level surface. When yourengine is cold, the coolant level should be at the FILL COLD mark.

If the LOW COOLANTmessage comes on and stayson, it means you’re low onengine coolant.

See “Low Coolant” in the Index.

yellowblue

6-31

Adding Coolant

If you need more coolant, add the proper DEX-COOL�

coolant mixture at the surge tank, but only when theengine is cool.

CAUTION:

You can be burned if you spill coolant on hotengine parts. Coolant contains ethylene glycol,and it will burn if the engine parts are hotenough. Don’t spill coolant on a hot engine.

When replacing the pressure cap, make sure it ishand-tight.

Coolant Surge Tank Pressure Cap

The coolant surge tank pressure cap must be fullyinstalled on the coolant surge tank.

yellowblue

6-32

NOTICE:

Your coolant surge tank pressure cap is a 15 psi(105 kPa) pressure-type cap and must be tightlyinstalled to prevent coolant loss and possibleengine damage from overheating.

Power Steering Fluid

When to Check Power Steering FluidIt is not necessary to regularly check power steeringfluid unless you suspect there is a leak in the system oryou hear an unusual noise. A fluid loss in this systemcould indicate a problem. Have the system inspected and repaired.

How to Check Power Steering FluidWhen the engine compartment is cool, wipe the cap andthe top of the reservoir clean, then unscrew the cap andwipe the dipstick with a clean rag. Replace the cap andcompletely tighten it. Then remove the cap again andlook at the fluid level on the dipstick.

The level should be at the FULL COLD mark. Ifnecessary, add only enough fluid to bring the level up tothe mark.

What to UseTo determine what kind of fluid to use, see“Recommended Fluids and Lubricants” in the Index.Always use the proper fluid. Failure to use the properfluid can cause leaks and damage hoses and seals.

yellowblue

6-33

Windshield Washer FluidWhat to UseWhen you need windshield washer fluid, be sure to readthe manufacturer’s instructions before use. If you will beoperating your vehicle in an area where the temperaturemay fall below freezing, use a fluid that has sufficientprotection against freezing.

Adding Washer Fluid

Open the cap labeled WASHER FLUID. Add washerfluid until the tank is full.

NOTICE:

� When using concentrated washer fluid,follow the manufacturer’s instructions foradding water.

� Don’t mix water with ready-to-use washerfluid. Water can cause the solution to freezeand damage your washer fluid tank andother parts of the washer system. Also,water doesn’t clean as well as washer fluid.

� Fill your washer fluid tank onlythree-quarters full when it’s very cold. This allows for expansion if freezing occurs,which could damage the tank if it iscompletely full.

� Don’t use engine coolant (antifreeze) inyour windshield washer. It can damageyour washer system and paint.

yellowblue

6-34

BrakesBrake Fluid

Your brake master cylinderreservoir is here. It is filledwith DOT-3 brake fluid.

There are only two reasons why the brake fluid level inthe reservoir might go down. The first is that the brakefluid goes down to an acceptable level during normalbrake lining wear. When new linings are put in, the fluidlevel goes back up. The other reason is that fluid isleaking out of the brake system. If it is, you should haveyour brake system fixed, since a leak means that sooneror later your brakes won’t work well, or won’t work at all.

So, it isn’t a good idea to “top off” your brake fluid.Adding brake fluid won’t correct a leak. If you add fluidwhen your linings are worn, then you’ll have too muchfluid when you get new brake linings. You should add(or remove) brake fluid, as necessary, only when work isdone on the brake hydraulic system.

CAUTION:

If you have too much brake fluid, it can spill on theengine. The fluid will burn if the engine is hotenough. You or others could be burned, and yourvehicle could be damaged. Add brake fluid onlywhen work is done on the brake hydraulic system.

Refer to the Maintenance Schedule to determine when tocheck your brake fluid. See “Periodic MaintenanceInspections” in the Index.

yellowblue

6-35

Checking Brake Fluid

You can check the brake fluid without taking off the cap.

Just look at the brake fluid reservoir. The fluid levelshould be above MIN. If it isn’t, have your brake systemchecked to see if there is a leak.

After work is done on the brake hydraulic system, makesure the level is above the MIN but not over the MAX mark.

What to Add

When you do need brake fluid, use only DOT-3 brakefluid. Refer to “Recommended Fluids and Lubricants”in the Index. Use new brake fluid from a sealedcontainer only.

Always clean the brake fluid reservoir cap and the areaaround the cap before removing it. This will help keepdirt from entering the reservoir.

CAUTION:

With the wrong kind of fluid in your brakesystem, your brakes may not work well, or theymay not even work at all. This could cause acrash. Always use the proper brake fluid.

yellowblue

6-36

NOTICE:

� Using the wrong fluid can badly damagebrake system parts. For example, just a fewdrops of mineral-based oil, such as engineoil, in your brake system can damage brakesystem parts so badly that they’ll have to bereplaced. Don’t let someone put in thewrong kind of fluid.

� If you spill brake fluid on your vehicle’spainted surfaces, the paint finish can bedamaged. Be careful not to spill brake fluidon your vehicle. If you do, wash it offimmediately. See “Appearance Care” in the Index.

Brake WearYour vehicle has four-wheel disc brakes.

Disc brake pads have built-in wear indicators that make ahigh-pitched warning sound when the brake pads are wornand new pads are needed. The sound may come and go orbe heard all the time your vehicle is moving (except whenyou are pushing on the brake pedal firmly).

CAUTION:

The brake wear warning sound means that soonyour brakes won’t work well. That could lead toan accident. When you hear the brake wearwarning sound, have your vehicle serviced.

NOTICE:

Continuing to drive with worn -out brake padscould result in costly brake repair.

yellowblue

6-37

Some driving conditions or climates may cause a brakesqueal when the brakes are first applied or lightlyapplied. This does not mean something is wrong withyour brakes.

Properly torqued wheel nuts are necessary to helpprevent brake pulsation. When tires are rotated, inspectbrake pads for wear and evenly torque wheel nuts in theproper sequence to GM specifications.

Brake linings should always be replaced as completeaxle sets.

See “Brake System Inspection” in Section 7 of this manualunder Part C “Periodic Maintenance Inspections.”

Brake Pedal TravelSee your dealer if the brake pedal does not return tonormal height, or if there is a rapid increase in pedaltravel. This could be a sign of brake trouble.

Brake AdjustmentEvery time you make a brake stop, your disc brakesadjust for wear.

Replacing Brake System PartsThe braking system on a vehicle is complex. Its manyparts have to be of top quality and work well together ifthe vehicle is to have really good braking. Your vehiclewas designed and tested with top-quality GM brakeparts. When you replace parts of your braking system -- for example, when your brake linings weardown and you have to have new ones put in -- be sureyou get new approved GM replacement parts. If youdon’t, your brakes may no longer work properly. Forexample, if someone puts in brake linings that are wrongfor your vehicle, the balance between your front andrear brakes can change -- for the worse. The brakingperformance you’ve come to expect can change in manyother ways if someone puts in the wrong replacementbrake parts.

yellowblue

6-38

BatteryYour new vehicle comes with a maintenance freeACDelco� battery. When it’s time for a new battery, getone that has the replacement number shown on the originalbattery’s label. We recommend an ACDelco battery.

Vehicle StorageIf you’re not going to drive your vehicle for 25 days or more, remove the black, negative (-) cable from the battery. This will help keep your battery from running down.

CAUTION:

Batteries have acid that can burn you and gasthat can explode. You can be badly hurt if youaren’t careful. See “Jump Starting” in the Indexfor tips on working around a battery withoutgetting hurt.

Contact your dealer to learn how to prepare your vehiclefor longer storage periods.

Also, for your audio system, see “Theft-DeterrentFeature” in the Index.

Bulb ReplacementFor any bulb changing procedure not listed in thissection, contact your GM dealership service department.

Before you replace any bulbs, be sure that all the lampsare off and the engine isn’t running. See “ReplacementBulbs” in the Index for the proper types of bulbs to use.

Halogen Bulbs

CAUTION:

Halogen bulbs have pressurized gas inside andcan burst if you drop or scratch the bulb. You orothers could be injured. Be sure to read andfollow the instructions on the bulb package.

yellowblue

6-39

Headlamps

1. Remove the two pins on the top of the headlampassembly. To remove the pins, turn the outer pinoutward and pull it straight up. To remove the innerpin, turn it inward and pull it straight up.

A. Low-Beam Headlamp

B. High-Beam Headlamp

2. Pull the headlamp lens assembly out.

3. Unplug the electrical connector.

4. Turn the bulb counterclockwise and remove it fromthe headlamp lens assembly.

5. Put the new bulb into the lens assembly and turn itclockwise until it is tight.

6. Plug in the electrical connector.

7. Put the headlamp lens assembly back into thevehicle. Install and tighten the two pins.

yellowblue

6-40

Front Turn Signal, Sidemarker andDaytime Running Lamps

A. Sidemarker Lamp

B. Retainer Clip

C. Front Turn Signal Lamp

D. Daytime Running Lamp

1. Remove the headlamp lens assembly as mentioned previously.

2. Press the retainer clip, located behind the turn signalhousing, towards the outside of the vehicle.

3. Pull the turn signal housing out from the vehicle.

4. Press the locking release lever, turn the bulb socketcounterclockwise and remove it from the turn signallens housing.

5. Remove the bulb from the bulb socket.

6. Put the new bulb into the bulb socket.

7. Put the bulb socket into the turn signal housing andturn it clockwise until it locks.

8. Put the turn signal housing back onto the vehicleplacing the hook and posts on the inner side into thealignment holes first and then the outer side into theretainer bracket until you hear a click.

9. Put the headlamp lens assembly back into the vehicle.

yellowblue

6-41

Center High-Mounted Stoplamp (CHMSL)and Cargo Lamp

1. Remove the screws and lift off the lamp assembly. A. Cargo Lamps

B. Center High-Mounted Stoplamps

2. Remove the CHMSL bulb holder back plate from thehousing by pressing the release tabs.

3. The CHMSL bulb is removed by pulling the bulbstraight out from the holder back plate. The cargolamp is removed by turning the socketcounterclockwise and pulling the bulb straight out.

yellowblue

6-42

4. If a CHMSL bulb is replaced, put the bulb into thesocket and press it in until it is tight.

5. If a cargo lamp is replaced, put a new cargo lampbulb into the socket and press it in until it is tightbefore turning the socket counterclockwise.

6. Put the bulb holder back plate into the lamp housing.

7. Replace the lamp assembly and tighten the screws.

Taillamps (Pickup Models)1. Open the tailgate.

2. Remove the two rearlamp assembly screwsnear the tailgate latchand pull out the lamp assembly.

yellowblue

6-43

A. Stoplamp

B. Turn Signal Lamp

C. Back-up Lamp

3. Press the release tab and turn the bulb socketcounterclockwise to remove it from the taillamp housing.

4. Pull the bulb straight out from the socket.

5. Press a new bulb into the socket and turn the socketclockwise into the taillamp housing until it clicks.

6. Reinstall the rear lamp assembly and tighten the screws.

7. Close the tailgate.

yellowblue

6-44

Taillamps (Chassis Cab Models)

A. Turn Signal Lamp

B. Stoplamp

C. Back-up Lamp

1. Using your hands, peel the rubber seal away fromthe lens.

2. Lift the lens off the lamp assembly.

3. Pull the bulb straight out from the socket.

4. Put a new bulb into the socket and press it in until itis tight.

5. Replace the lens and the lens seal.

Windshield Wiper Blade Replacement

Windshield wiper blades should be inspected at leasttwice a year for wear and cracking. See “Wiper BladeCheck” in Section 7 of this manual under Part B “OwnerChecks and Services” for more information.

Replacement blades come in different types and areremoved in different ways. For proper type and length,see “Normal Maintenance Replacement Parts” in theIndex. Here’s how to remove the Shephard’s Hook type.

yellowblue

6-45

To replace the windshield wiper blade assembly:

1. Lift the wiper arm and turn the blade until it is facingaway from the windshield.

2. Push the release lever and slide the wiper assemblytoward the driver’s side of the vehicle.

3. Install a new blade by reversing Steps 1 and 2.

TiresYour new vehicle comes with high-quality tires made bya leading tire manufacturer. If you ever have questionsabout your tire warranty and where to obtain service, seeyour GM Warranty booklet for details.

CAUTION:

Poorly maintained and improperly used tires are dangerous.� Overloading your tires can cause

overheating as a result of too much friction.You could have an air-out and a seriousaccident. See “Loading Your Vehicle” in the Index.

� Underinflated tires pose the same danger asoverloaded tires. The resulting accidentcould cause serious injury. Check all tiresfrequently to maintain the recommendedpressure. Tire pressure should be checkedwhen your tires are cold.

� Overinflated tires are more likely to be cut, punctured or broken by a suddenimpact -- such as when you hit a pothole.Keep tires at the recommended pressure.

� Worn, old tires can cause accidents. If yourtread is badly worn, or if your tires havebeen damaged, replace them.

yellowblue

6-46

Inflation -- Tire PressureThe Certification/Tire label, which is on the rear edge ofthe driver’s door, shows the correct inflation pressuresfor your tires when they’re cold. “Cold” means yourvehicle has been sitting for at least three hours or drivenno more than 1 mile (1.6 km).

NOTICE:

Don’t let anyone tell you that underinflation oroverinflation is all right. It’s not. If your tiresdon’t have enough air (underinflation), you canget the following:� Too much flexing� Too much heat� Tire overloading� Bad wear� Bad handling� Bad fuel economy.

NOTICE: (Continued)

NOTICE: (Continued)

If your tires have too much air (overinflation),you can get the following:� Unusual wear� Bad handling� Rough ride� Needless damage from road hazards.

When to Check

Check your tires once a month or more. Also, check thetire pressure of the spare tire.

How to Check

Use a good quality pocket-type gage to check tirepressure. You can’t tell if your tires are properly inflatedsimply by looking at them. Radial tires may lookproperly inflated even when they’re underinflated.

Be sure to put the valve caps back on the valve stems.They help prevent leaks by keeping out dirt and moisture.

yellowblue

6-47

Tire Inspection and RotationTires should be rotated every 6,000 to 8,000 miles (10 000 to 13 000 km). Any time you notice unusualwear, rotate your tires as soon as possible and checkwheel alignment. Also check for damaged tires orwheels. See “When It’s Time for New Tires” and“Wheel Replacement” later in this section for moreinformation. Make sure the spare tire is stored securely.Push, pull, and then try to rotate or turn the tire. If itmoves, use to tighten the cable. See “Storing a Flat orSpare Tire and Tools” in the Index.

The purpose of regular rotation is to achieve moreuniform wear for all tires on the vehicle. The firstrotation is the most important. See “ScheduledMaintenance Services” in the Index for scheduledrotation intervals.

When rotating your tires, always use one of the correctrotation patterns shown here.

After the tires have been rotated, adjust the front andrear inflation pressures as shown on theCertification/Tire label. Make certain that all wheel nutsare properly tightened. See “Wheel Nut Torque” in the Index.

yellowblue

6-48

CAUTION:

Rust or dirt on a wheel, or on the parts to whichit is fastened, can make wheel nuts become looseafter a time. The wheel could come off and causean accident. When you change a wheel, removeany rust or dirt from places where the wheelattaches to the vehicle. In an emergency, you canuse a cloth or a paper towel to do this; but besure to use a scraper or wire brush later, if youneed to, to get all the rust or dirt off. (See “Changing a Flat Tire” in the Index.)

When It’s Time for New Tires

One way to tell when it’stime for new tires is tocheck the treadwearindicators, which willappear when your tires haveonly 1/16 inch (1.6 mm) orless of tread remaining.

You need a new tire if any of the following statementsare true:

� You can see the indicators at three or more placesaround the tire.

� You can see cord or fabric showing through the tire’s rubber.

� The tread or sidewall is cracked, cut or snagged deepenough to show cord or fabric.

� The tire has a bump, bulge or split.

� The tire has a puncture, cut or other damage thatcan’t be repaired well because of the size or locationof the damage.

yellowblue

6-49

Buying New TiresTo find out what kind and size of tires you need, look atthe Certification/Tire label.

The tires installed on your vehicle when it was new hada Tire Performance Criteria Specification (TPC Spec)number on each tire’s sidewall. When you get new tires,get ones with that same TPC Spec number. That wayyour vehicle will continue to have tires that are designedto give proper endurance, handling, speed rating,traction, ride and other things during normal service onyour vehicle. If your tires have an all-season treaddesign, the TPC number will be followed by an “MS”(for mud and snow).

If you ever replace your tires with those not having aTPC Spec number, make sure they are the same size,load range, speed rating and construction type (bias,bias-belted or radial) as your original tires.

CAUTION:

Mixing tires could cause you to lose control whiledriving. If you mix tires of different sizes or types(radial and bias-belted tires), the vehicle may nothandle properly, and you could have a crash.Using tires of different sizes may also causedamage to your vehicle. Be sure to use the samesize and type tires on all wheels.

CAUTION:

If you use bias-ply tires on your vehicle, thewheel rim flanges could develop cracks aftermany miles of driving. A tire and/or wheel couldfail suddenly, causing a crash. Use only radial-plytires with the wheels on your vehicle.

yellowblue

6-50

Uniform Tire Quality GradingThe following information relates to the systemdeveloped by the United States National HighwayTraffic Safety Administration, which grades tires bytreadwear, traction and temperature performance. (This applies only to vehicles sold in the United States.)The grades are molded on the sidewalls of mostpassenger car tires. The Uniform Tire Quality Gradingsystem does not apply to deep tread, winter-type snowtires, space-saver or temporary use spare tires, tires withnominal rim diameters of 10 to 12 inches (25 to 30 cm),or to some limited-production tires.

While the tires available on General Motors passengercars and light trucks may vary with respect to thesegrades, they must also conform to Federal safetyrequirements and additional General Motors TirePerformance Criteria (TPC) standards.

Treadwear

The treadwear grade is a comparative rating based onthe wear rate of the tire when tested under controlledconditions on a specified government test course. Forexample, a tire graded 150 would wear one and a half (1 1/2) times as well on the government course as a tiregraded 100. The relative performance of tires dependsupon the actual conditions of their use, however, andmay depart significantly from the norm due to variationsin driving habits, service practices and differences inroad characteristics and climate.

Traction -- AA, A, B, C

The traction grades, from highest to lowest, are AA, A,B, and C. Those grades represent the tire’s ability to stopon wet pavement as measured under controlledconditions on specified government test surfaces ofasphalt and concrete. A tire marked C may have poortraction performance. Warning: The traction gradeassigned to this tire is based on straight-ahead brakingtraction tests, and does not include acceleration,cornering, hydroplaning, or peak traction characteristics.

yellowblue

6-51

Temperature -- A, B, C

The temperature grades are A (the highest), B, and C,representing the tire’s resistance to the generation ofheat and its ability to dissipate heat when tested undercontrolled conditions on a specified indoor laboratorytest wheel. Sustained high temperature can cause thematerial of the tire to degenerate and reduce tire life, andexcessive temperature can lead to sudden tire failure.The grade C corresponds to a level of performancewhich all passenger car tires must meet under theFederal Motor Vehicle Safety Standard No. 109. GradesB and A represent higher levels of performance on thelaboratory test wheel than the minimum required by law.

Warning: The temperature grade for this tire isestablished for a tire that is properly inflated and notoverloaded. Excessive speed, underinflation, orexcessive loading, either separately or in combination,can cause heat buildup and possible tire failure.

Wheel Alignment and Tire BalanceThe wheels on your vehicle were aligned and balancedcarefully at the factory to give you the longest tire lifeand best overall performance.

Scheduled wheel alignment and wheel balancing are notneeded. However, if you notice unusual tire wear oryour vehicle pulling one way or the other, the alignmentmay need to be reset. If you notice your vehiclevibrating when driving on a smooth road, your wheelsmay need to be rebalanced.

Wheel ReplacementReplace any wheel that is bent, cracked, or badly rustedor corroded. If wheel nuts keep coming loose, the wheel,wheel bolts and wheel nuts should be replaced. If thewheel leaks air, replace it (except some aluminumwheels, which can sometimes be repaired). See yourdealer if any of these conditions exist.

Your dealer will know the kind of wheel you need.

Each new wheel should have the same load-carryingcapacity, diameter, width, offset and be mounted thesame way as the one it replaces.

If you need to replace any of your wheels, wheel boltsor wheel nuts, replace them only with new GM originalequipment parts. This way, you will be sure to have theright wheel, wheel bolts and wheel nuts for your vehicle.

yellowblue

6-52

CAUTION:

Using the wrong replacement wheels, wheel boltsor wheel nuts on your vehicle can be dangerous.It could affect the braking and handling of yourvehicle, make your tires lose air and make youlose control. You could have a collision in whichyou or others could be injured. Always use thecorrect wheel, wheel bolts and wheel nuts for replacement.

NOTICE:

The wrong wheel can also cause problems withbearing life, brake cooling, speedometer orodometer calibration, headlamp aim, bumperheight, vehicle ground clearance and tire or tirechain clearance to the body and chassis.

See “Changing a Flat Tire” in the Index for more information.

Used Replacement Wheels

CAUTION:

Putting a used wheel on your vehicle isdangerous. You can’t know how it’s been used orhow far it’s been driven. It could fail suddenlyand cause an accident. If you have to replace awheel, use a new GM original equipment wheel.

Tire Chains

NOTICE:

If your vehicle has P265/75R16 or LT265/75R16size tires, don’t use tire chains. They can damageyour vehicle because there’s not enough clearance.

NOTICE: (Continued)

yellowblue

6-53

NOTICE: (Continued)

Use another type of traction device only if itsmanufacturer recommends it for use on yourvehicle and tire size combination and roadconditions. Follow that manufacturer’sinstructions. To help avoid damage to yourvehicle, drive slowly, readjust or remove thedevice if it’s contacting your vehicle, and don’tspin your wheels.If you do find traction devices that will fit, installthem on the rear tires.If use tire chains only where legal and only whenyou must. Use chains that are the proper size foryour tires. Install them on the tires of the rear axle.

Don’t use chains on the tires of the front axle.Tighten them as tightly as possible with the endssecurely fastened. Drive slowly and follow the chainmanufacturer’s instructions. If you can hear thechains contacting your vehicle, stop and retightenthem. If the contact continues, slow down until itstops. Driving too fast or spinning the wheels withchains on will damage your vehicle.

Appearance CareRemember, cleaning products can be hazardous. Someare toxic. Others can burst into flame if you strike amatch or get them on a hot part of the vehicle. Some aredangerous if you breathe their fumes in a closed space.When you use anything from a container to clean yourvehicle, be sure to follow the manufacturer’s warningsand instructions. And always open your doors orwindows when you’re cleaning the inside.

Never use these to clean your vehicle:

� Gasoline

� Benzene

� Naphtha

� Carbon Tetrachloride

� Acetone

� Paint Thinner

� Turpentine

� Lacquer Thinner

� Nail Polish Remover

They can all be hazardous -- some more than others -- and they can all damage your vehicle, too.

yellowblue

6-54

Don’t use any of these unless this manual says you can.In many uses, these will damage your vehicle:

� Alcohol

� Laundry Soap

� Bleach

� Reducing Agents

Cleaning the Inside of Your VehicleUse a vacuum cleaner often to get rid of dust and loosedirt. Wipe vinyl, leather, plastic and painted surfaceswith a clean, damp cloth.

Cleaning of Fabric/CarpetYour dealer has two cleaners, Multi-Purpose InteriorCleaner and Capture Non-Solvent Dry Spot and SoilRemover for cleaning fabric and carpet. They will cleannormal spots and stains very well. You can getGM-approved cleaning products from your dealer. (See “Appearance Care and Materials” in the Index.)

Here are some cleaning tips:

� Always read the instructions on the cleaner label.

� Clean up stains as soon as you can -- before they set.

� Carefully scrape off any excess stain.

� Use a clean cloth or sponge, and change to a clean areaoften. A soft brush may be used if stains are stubborn.

� If a ring forms on fabric after spot cleaning, clean theentire area immediately or it will set.

Using Multi-Purpose Interior Cleaner on Fabric1. Vacuum and brush the area to remove any loose dirt.

2. Always clean a whole trim panel or section. Mask surrounding trim along stitch or welt lines.

3. Mix powdered cleaner following the directions onthe container label to form thick suds.

4. Use suds only and apply with a clean sponge. Don’t saturate the material and don’t rub it roughly.

5. As soon as you’ve cleaned the section, use a spongeto remove the suds.

6. Wipe cleaned area with a clean, damp towel or cloth.

7. Wipe with a clean cloth and let dry.

yellowblue

6-55

Special Fabric Cleaning ProblemsStains caused by such things as catsup, coffee (black),egg, fruit, fruit juice, milk, soft drinks, vomit, urine andblood can be removed as follows:

1. Carefully scrape off excess stain, then sponge thesoiled area with cool water.

2. If a stain remains, follow the multi-purpose interiorcleaner instructions described earlier.

3. If an odor lingers after cleaning vomit or urine, treatthe area with a water/baking soda solution: 1 teaspoon (5 ml) of baking soda to 1 cup (250 ml)of lukewarm water.

4. Let dry.

Stains caused by candy, ice cream, mayonnaise, chilisauce and unknown stains can be removed as follows:

1. Carefully scrape off excess stain.

2. First, clean with cool water and allow to dry completely.

3. If a stain remains, follow instructions forMulti -Purpose Interior Cleaner.

Cleaning VinylUse warm water and a clean cloth.

� Rub with a clean, damp cloth to remove dirt. You may have to do it more than once.

� Things like tar, asphalt and shoe polish will stain if youdon’t get them off quickly. Use a clean cloth and avinyl/leather cleaner. See your dealer for this product.

Cleaning LeatherUse a soft cloth with lukewarm water and a mild soap orsaddle soap and wipe dry with a soft cloth. Then, let theleather dry naturally. Do not use heat to dry.

� For stubborn stains, use a leather cleaner. See yourdealer for this product.

� Never use oils, varnishes, solvent-based or abrasivecleaners, furniture polish or shoe polish on leather.

� Soiled or stained leather should be cleanedimmediately. If dirt is allowed to work into thefinish, it can harm the leather.

yellowblue

6-56

Cleaning the Top of the Instrument PanelUse only mild soap and water to clean the top surfacesof the instrument panel. Sprays containing silicones orwaxes may cause annoying reflections in the windshieldand even make it difficult to see through the windshieldunder certain conditions.

Cleaning Interior Plastic ComponentsUse only a mild soap and water solution on a soft clothor sponge. Commercial cleaners may affect the surface finish.

Care of Safety BeltsKeep belts clean and dry.

CAUTION:

Do not bleach or dye safety belts. If you do, itmay severely weaken them. In a crash, theymight not be able to provide adequate protection.Clean safety belts only with mild soap andlukewarm water.

Cleaning Glass SurfacesGlass should be cleaned often. GM Glass Cleaner or a liquid household glass cleaner will remove normaltobacco smoke and dust films on interior glass. (See “Appearance Care and Materials” in the Index.)

Don’t use abrasive cleaners on glass, because they maycause scratches. Avoid placing decals on the inside rearwindow, since they may have to be scraped off later. Ifabrasive cleaners are used on the inside of the rearwindow, an electric defogger element may be damaged.Any temporary license should not be attached across thedefogger grid.

Cleaning the Outside of theWindshield and Wiper BladesIf the windshield is not clear after using the windshieldwasher, or if the wiper blade chatters when running, wax,sap or other material may be on the blade or windshield.

Clean the outside of the windshield with GMWindshield Cleaner, Bon Ami� Powder (non-scratchingglass cleaning powder), GM Part No. 1050011. Thewindshield is clean if beads do not form when you rinseit with water.

yellowblue

6-57

Grime from the windshield will stick to the wiper bladesand affect their performance. Clean the blade by wipingvigorously with a cloth soaked in full-strength windshieldwasher solvent. Then rinse the blade with water.

Check the wiper blades and clean them as necessary;replace blades that look worn.

WeatherstripsSilicone grease on weatherstrips will make them lastlonger, seal better, and not stick or squeak. Applysilicone grease with a clean cloth at least every sixmonths. During very cold, damp weather more frequentapplication may be required. (See “RecommendedFluids and Lubricants” in the Index.)

Cleaning the Outside of Your VehicleThe paint finish on your vehicle provides beauty, depthof color, gloss retention and durability.

Washing Your VehicleThe best way to preserve your vehicle’s finish is to keep itclean by washing it often with lukewarm or cold water.

Don’t wash your vehicle in the direct rays of the sun.Use a car washing soap. Don’t use strong soaps orchemical detergents. Be sure to rinse the vehicle well,removing all soap residue completely. You can getGM-approved cleaning products from your dealer. (See“Appearance Care and Materials” in the Index.) Don’tuse cleaning agents that are petroleum based, or thatcontain acid or abrasives. All cleaning agents should beflushed promptly and not allowed to dry on the surface,or they could stain. Dry the finish with a soft, cleanchamois or an all-cotton towel to avoid surfacescratches and water spotting.

High pressure car washes may cause water to enter your vehicle.

Cleaning Exterior Lamps/LensesUse lukewarm or cold water, a soft cloth and a carwashing soap to clean exterior lamps and lenses. Follow instructions under “Washing Your Vehicle.”

yellowblue

6-58

Finish CareOccasional waxing or mild polishing of your vehicle byhand may be necessary to remove residue from the paintfinish. You can get GM-approved cleaning productsfrom your dealer. (See “Appearance Care and Materials”in the Index.)

Your vehicle may have a “basecoat/clearcoat” paintfinish. The clearcoat gives more depth and gloss to thecolored basecoat. Always use waxes and polishes thatare non-abrasive and made for a basecoat/clearcoat paint finish.

NOTICE:

Machine compounding or aggressive polishing ona basecoat/clearcoat paint finish may dull thefinish or leave swirl marks.

Foreign materials such as calcium chloride and othersalts, ice melting agents, road oil and tar, tree sap, birddroppings, chemicals from industrial chimneys, etc., candamage your vehicle’s finish if they remain on paintedsurfaces. Wash the vehicle as soon as possible. Ifnecessary, use non-abrasive cleaners that are markedsafe for painted surfaces to remove foreign matter.

Exterior painted surfaces are subject to aging, weatherand chemical fallout that can take their toll over a periodof years. You can help to keep the paint finish lookingnew by keeping your vehicle garaged or coveredwhenever possible.

Protecting Exterior Bright Metal PartsBright metal parts should be cleaned regularly to keeptheir luster. Washing with water is all that is usuallyneeded. However, you may use chrome polish onchrome or stainless steel trim, if necessary.

Use special care with aluminum trim. To avoiddamaging protective trim, never use auto or chromepolish, steam or caustic soap to clean aluminum. Acoating of wax, rubbed to high polish, is recommendedfor all bright metal parts.

yellowblue

6-59

Cleaning Aluminum orChrome-Plated Wheels (If Equipped)Keep your wheels clean using a soft clean cloth withmild soap and water. Rinse with clean water. Afterrinsing thoroughly, dry with a soft clean towel. A waxmay then be applied.

The surface of these wheels is similar to the paintedsurface of your vehicle. Don’t use strong soaps,chemicals, abrasive polishes, abrasive cleaners, cleanerswith acid or abrasive cleaning brushes on them becauseyou could damage the surface. Do not use chrome polishon any wheels other than chrome-plated wheels.

Use chrome polish only on chrome-plated wheels, butavoid any painted surface of the wheel, and buff offimmediately after application.

Don’t take your vehicle through an automatic car washthat has silicon carbide tire cleaning brushes. Thesebrushes can also damage the surface of these wheels.

Cleaning TiresTo clean your tires, use a stiff brush with a tire cleaner.

NOTICE:

When applying a tire dressing always take care towipe off any overspray or splash from all paintedsurfaces on the body or wheels of the vehicle.Petroleum-based products may damage the paintfinish and tires.

Sheet Metal DamageIf your vehicle is damaged and requires sheet metalrepair or replacement, make sure the body repair shopapplies anti-corrosion material to the parts repaired orreplaced to restore corrosion protection.

Original manufacturer replacement parts will providethe corrosion protection while maintaining the warranty.

yellowblue

6-60

Finish DamageAny stone chips, fractures or deep scratches in the finishshould be repaired right away. Bare metal will corrodequickly and may develop into a major repair expense.

Minor chips and scratches can be repaired with touch-upmaterials available from your dealer or other serviceoutlets. Larger areas of finish damage can be correctedin your dealer’s body and paint shop.

Underbody MaintenanceChemicals used for ice and snow removal and dustcontrol can collect on the underbody. If these are notremoved, accelerated corrosion (rust) can occur on theunderbody parts such as fuel lines, frame, floor pan and exhaust system even though they have corrosion protection.

At least every spring, flush these materials from theunderbody with plain water. Clean any areas where mudand other debris can collect. Dirt packed in closed areasof the frame should be loosened before being flushed.Your dealer or an underbody car washing system can dothis for you.

Chemical Paint SpottingSome weather and atmospheric conditions can create achemical fallout. Airborne pollutants can fall upon andattack painted surfaces on your vehicle. This damagecan take two forms: blotchy, ringlet-shapeddiscolorations, and small irregular dark spots etched intothe paint surface.

Although no defect in the paint job causes this, GM willrepair, at no charge to the owner, the surfaces of newvehicles damaged by this fallout condition within 12 months or 12,000 miles (20 000 km) of purchase,whichever occurs first.

This applies only to materials manufactured and sold byGeneral Motors. Bodies, body conversions or equipmentnot made or sold by General Motors are not covered.

yellowblue

6-61

GM Vehicle Care/Appearance Materials

PART NUMBER SIZE DESCRIPTION USAGE

994954 23 in. x 25 in. Polishing Cloth – Wax Treated Exterior polishing cloth

1050172 16 oz. (0.473 L) Tar and Road Oil Remover Removes tar, road oil and asphalt

1050173 16 oz. (0.473 L) Chrome Cleaner and Polish Use on chrome, stainless steel, nickel, copper and brass

1050174 16 oz. (0.473 L) White Sidewall Tire Cleaner Removes soil and black marks from whitewalls

1050214 32 oz. (0.946 L) Vinyl Cleaner Cleans vinyl tops, upholstery and convertible tops

1050427 23 oz. (0.680 L) Glass Cleaner Removes dirt, grime, smoke and fingerprints

1052918** 8 oz. (0.237 L) Armor All� Protectant Protects leather, wood, acrylics, Plexiglas�, plastic,rubber and vinyl

1052925 16 oz. (0.473 L) Multi-Purpose InteriorCleaner

Cleans carpets, seats, interior trim, door panels and floor mats

1052929 16 oz. (0.473 L) Wheel Cleaner Spray on and rinse with water

1052930 8 oz. (0.237 L) Capture Dry Spot Remover Attracts, absorbs and removes soils on fabric

12345721 2.5 sq. ft. Synthetic Chamois Shines vehicle without scratching

12345725 12 oz. (0.354 L) Silicone Tire Shine Spray on tire shine

12377964* 16 oz. (0.473 L) Finish Enhancer Removes dust, fingerprints and surface contaminants

12377966* 16 oz. (0.473 L) Cleaner Wax Removes light scratches and oxidation and protects finish

12377984* 16 oz. (0.473 L) Surface Cleaner Removes contaminants, blemishes and swirl marks

See your General Motors Parts Department for these products. * For exterior use only.See “Recommended Fluids and Lubricants” in the Index. **Not recommended for use on instrument panels.

yellowblue

6-62

Vehicle Identification Number (VIN)

This is the legal identifier for your vehicle. It appears ona plate in the front corner of the instrument panel, on thedriver’s side. You can see it if you look through thewindshield from outside your vehicle. The VIN alsoappears on the Vehicle Certification and Service Partslabels and the certificates of title and registration.

Engine IdentificationThe 8th character in your VIN is the engine code. Thiscode will help you identify your engine, specificationsand replacement parts.

Service Parts Identification LabelYou’ll find this label on the inside of the glove box. It’svery helpful if you ever need to order parts. On thislabel is:

� your VIN,

� the model designation,

� paint information and

� a list of all production options and special equipment.

Be sure that this label is not removed from the vehicle.

yellowblue

6-63

Electrical SystemAdd-On Electrical Equipment

NOTICE:

Don’t add anything electrical to your vehicleunless you check with your dealer first. Someelectrical equipment can damage your vehicleand the damage wouldn’t be covered by yourwarranty. Some add-on electrical equipment cankeep other components from working as they should.

Your vehicle has an air bag system. Before attempting toadd anything electrical to your vehicle, see “ServicingYour Air Bag-Equipped Vehicle” in the Index.

Windshield WipersThe windshield wiper motor is protected by an internalcircuit breaker and a fuse. If the motor overheats due toheavy snow, etc., the wiper will stop until the motorcools. If the overload is caused by some electricalproblem and not snow, etc., be sure to get it fixed.

Power Windows and Other Power OptionsCircuit breakers protect the power windows and otherpower accessories. When the current load is too heavy,the circuit breaker opens and closes, protecting thecircuit until the problem is fixed or goes away.

Fuses and Circuit BreakersThe wiring circuits in your vehicle are protected fromshort circuits by a combination of fuses, circuit breakersand fusible thermal links. This greatly reduces thechance of fires caused by electrical problems.

Look at the silver-colored band inside the fuse. If theband is broken or melted, replace the fuse. Be sure youreplace a bad fuse with a new one of the identical sizeand rating.

If you ever have a problem on the road and don’t have aspare fuse, you can borrow one that has the sameamperage. Just pick some feature of your vehicle thatyou can get along without -- like the radio or cigarettelighter -- and use its fuse, if it is the correct amperage.Replace it as soon as you can.

yellowblue

6-64

Instrument Panel Fuse Block

The fuse block access dooris on the driver’s side edgeof the instrument panel. Pulloff the cover to access thefuse block.

You can remove fuses with a fuse extractor which ismounted to the fuse block access door. To remove fusesif you don’t have a fuse extractor, hold the end of thefuse between your thumb and index finger and pullstraight out.

You may have spare fuses located behind the fuse blockaccess door. These can be used to replace a bad fuse.However, make sure it is of the correct amperage.

NAME Usage

L BODY Retained Accessory Power Relay

LOCK Power Door Locks

DRV UNLOCK Power Door Lock Relay

LOCK Power Door Lock Relay

HVAC 1 Climate Control System

yellowblue

6-65

NAME Usage

CRUISE Cruise Control, Instrument Cluster

IGN 3 Ignition, Power Seats

4WD Four-Wheel Drive System,Auxiliary Battery

CRANK Starting System

INT PRK Parking Lamps, SidemarkerLamps, Interior Lamps

L DOOR Power Door Lock Relay

BRAKE Anti-Lock Brake System

RR WIPER Not Used

ILLUM Interior Lamps

SEAT Power Seat Circuit Breaker

TURN Exterior Lamps, Turn Signals,Hazard Lamps

UNLOCK Power Door Locks

HTR A/C Climate Control System

NAME Usage

WS WPR Windshield Wipers

IGN 1 Ignition, Instrument Panel

AIR BAG Air Bag

MIR/LOCK Power Mirrors, Power Door Locks

DR LOCK Power Door Locks

PWR WDO Power Window Circuit Breaker

UNLOCK Power Door Lock Relay

IGN 0 PRND321 Display, Odometer,VCM/PCM

SEO IGN Special Equipment Option,Ignition, Manual Selectable Ride

SEO ACCY Special Equipment OptionAccessory, Cellular Telephone

RAP #1 Retained Accessory Power Relay

RDO 1 Audio System

RAP #2 Not Used

yellowblue

6-66

Center Instrument Panel Utility Block

The center instrument panel utility block is locatedunderneath the instrument panel, to the left of thesteering column.

Relay Name Usage

SEO Special Equipment Option

HTD ST Heated Seats

SPARE 4 Not Used

Relay Name Usage

VANITY Headliner Wiring

TRAILER Trailer Brake Wiring

PWR ST Power Seats

SPARE 5 Not Used

CLUTCH Manual Transmission Clutch Switch

UPF Upfitter

PARK LAMP Parking Lamps

FRT PRK EXPT Not Used

SL RIDE Manual Selectable Ride Switch

SPARE 2 Not Used

RR PRK LP Not Used

RR FOG LP Not Used

SPARE 3 Not Used

INAV PWR Interior Lights Feed

CTSY LP Courtesy Lamps

CEL PHONE Cellular Telephone Wiring

yellowblue

6-67

Underhood Electrical Center The underhood electrical center is located on thedriver’s side of the engine compartment near the battery.Lift the cover for access to the fuse/relay block.

You can remove fuses with a fuse extractor. The fuseextractor is located in the underhood electrical center. Toremove fuses if you don’t have a fuse extractor, hold theend of the fuse between your thumb and index fingerand pull straight out.

yellowblue

6-68

yellowblue

6-69

Name UsageSTUD #1 Accessory Power/Trailer

Wiring FeedABS Anti-Lock BrakesIGN A Ignition SwitchAIR A.I.R. SystemRAP #1 Retained Accessory Power, Power

Mirrors, Power Door Locks,Power Seat(s)

IGN B Ignition SwitchRAP #2 Not UsedSTUD #2 Accessory Power/Trailer Wiring

Brake FeedTRL R TRN Right Turn Signal Trailer WiringTRL L TRN Left Turn Signal Trailer WiringIGN 1 Ignition, Fuel ControlsINJ B Ignition, Fuel Controls (Relay)STARTER Starter (Relay)PARK LP Parking LampsFRT HVAC Climate Control SystemSTOP LP Exterior Lamps, StoplampsECM 1 VCM/PCMCHMSL Center High Mounted StoplampVEH STOP Stoplamps, Cruise ControlTRL B/U Backup Lamps Trailer Wiring

Name UsageINJ A Fuel Controls, IgnitionRR HVAC Not UsedVEH B/U Vehicle Backup LampsENG 1 Engine Controls, Canister Purge,

Fuel SystemETC Electronic Throttle ControlIGN E A/C Compressor Relay, Rear

Window Defogger, DaytimeRunning Lamps, A.I.R. System

B/U LP Backup Lamps, AutomaticTransmission Shift Lock Control System

ATC Automatic Transfer CaseRR DEFOG Rear Window Defogger, Heated

Mirrors (Relay)RR PRK Right Rear Parking LampsECM B VCM/PCMF/PMP Fuel Pump (Relay)O2 A Oxygen SensorsO2 B Oxygen SensorsLR PRK Left Rear Parking LampsRR DEFOG Rear Window Defogger,

Heated MirrorsHDLP Headlamps (Relay)

yellowblue

6-70

Name UsageTRL PRK Parking Lamps Trailer WiringRT HDLP Right HeadlampsDRL Daytime Running Lamps (Relay)HTD MIR Heated MirrorsLT HDLP Left HeadlampsA/C Air ConditioningAUX PWR Cigarette Lighter, Auxiliary

Power OutletsSEO 2 Special Equipment Option Power,

Power Seats, Aux Roof Mnt LampSEO 1 Special Equipment Option Power,

Aux Roof Mnt Lamp, Cell PhoneDRL Daytime Running LampsA/C A/C (Relay)FOG LP Fog LampsFOG LP Fog Lamps (Relay)RADIO Audio System, Instrument Cluster,

Climate Control SystemCIGAR Cigarette Lighter, Auxiliary

Power Outlets

Name UsageRT TURN Right Turn SignalsBTSI Automatic Transmission Shift

Lock Control SystemLT TURN Left Turn SignalsFR PRK Front Parking Lamps,

Sidemarker LampsW/W PMP Windshield Washer PumpHORN Horn (Relay)IGN C Ignition Switch, Fuel Pump,

PRND321 Display, CrankRDO AMP Not UsedHAZ LP Exterior Lamps, Hazard LampsEXP LPS Not UsedHORN HornCTSY LP Interior LampsRR WPR Not UsedTBC Body Control Module, Remote

Keyless Entry, Headlamps

yellowblue

6-71

Replacement Bulbs*Low-Beam Headlamps 2 9006

High-Beam Headlamps 2 9005

Daytime Running Lamps (DRL) 2 3157KX

Front Marker Lamp 2 194

Front Parking and Turn Lamp 2 3157NA

Rear Marker Lamp, Taillamp and Stop Lamp 2 3157

Taillamp and Stop Lamp** 2 1157

Rear Turn Lamp 2 3157

Rear Turn Lamp ** 2 1156

Back-up Lamp 2 3157

Back-up Lamp ** 2 1156

Center High-Mounted Stoplamp 2 912

Cargo Lamp 2 912

* For replacement bulbs not listed here, please consult your dealer.

** Chassis Cab Models

yellowblue

6-72

Capacities and SpecificationsPlease refer to “Recommended Fluids and Lubricants” in the Index for more information. See refrigerant charge labelunder the hood for charge capacity information and requirements.

Engine Type VIN Code Spark Plug Gap

VORTEC 4300 V6 W 0.060 inches (1.52 mm)

VORTEC 4800 V8 V 0.060 inches (1.52 mm)

VORTEC 5300 V8 T 0.060 inches (1.52 mm)

VORTEC 6000 V8 U 0.060 inches (1.52 mm)

Wheels and TiresModel Description Torque

C/K 1500 6 bolts (14mm) 140 lb-ft (190 N·m)

C/K 2500 8 bolts (14mm) 140 lb-ft (190 N·m)

Tire Pressure See the Certification/Tire label on the rear edge of the driver’s door or the incomplete vehicle document in the cab.

yellowblue

6-73

Cooling System Capacity (Approximate)After refill, the level must be rechecked. See “Cooling System” in the Index.

Engine Transmission Quantity

VORTEC 4300 V6 Automatic 12.6 quarts (11.9 L)

VORTEC 4300 V6 Manual 12.9 quarts (12.2 L)

VORTEC 4800 V8 Automatic 13.4 quarts (12.7 L)

VORTEC 4800 V8 Manual 13.7 quarts (13.0 L)

VORTEC 5300 V8 Automatic 13.4 quarts (12.7 L)

VORTEC 5300 V8** Automatic 14.9 quarts (14.1 L)

VORTEC 6000 V8 Automatic 14.8 quarts (14.0 L)

VORTEC 6000 V8* Automatic 14.4 quarts (13.6 L)

VORTEC 6000 V8 Manual 15.2 quarts (14.4 L)

VORTEC 6000 V8* Manual 14.8 quarts (14.0 L)

* Vehicles equipped with the optional engine oil cooler.

** Vehicles equipped with the optional air conditioner.

yellowblue

6-74

Crankcase Capacity (Approximate)After refill, the level must be rechecked. Add enough engine oil so that the fluid is within the proper operating range.See “Engine Oil” in the Index.

Engine VIN Quantity with Filter �

VORTEC 4300 V6 W 4.5 quarts (4.3 L)

VORTEC 4800 V8 V 6.0 quarts (5.7 L)

VORTEC 5300 V8 T 6.0 quarts (5.7 L)

VORTEC 6000 V8 U 6.0 quarts (5.7 L)

�Oil filter should be changed at every oil change.

Fuel Tank Capacity (Approximate)Type Quantity

Short Bed 26.0 gallons (98.0 L)

Long Bed 34.0 gallons (128.0 L)

Chassis Cab 34.0 gallons (128.0 L)

yellowblue

6-75

Normal Maintenance Replacement PartsReplacement part numbers listed in this section are based on the latest information available at the time of printing,and are subject to change. If a part listed in this manual is not the same as the part used in your vehicle when it wasbuilt, or if you have any questions, please contact your GM dealer.

These specifications are for information only. If you have any questions, see the service manual for the chassis orrefer to the body manufacturer’s publications.

VIN Code W V T U

Oil Filter* PF47 PF59 PF59 PF59

Engine Air Cleaner/Filter* A1519C� A1519C� A1519C� A1518C

Passenger Compartment Air Filter Kit** 52485513 52485513 52485513 52485513

PCV Valve* CV769C CV948C CV948C CV948C

Spark Plugs* 41-932 41-952 41-952 41-952

Fuel Filter* GF626 GF626 GF626 GF626

Wiper Blades** 15706394 15706394 15706394 15706394

Wiper Blade Type ITTA ITTA ITTA ITTA

Wiper Blade Length 22 inches(56.0 cm)

22 inches(56.0 cm)

22 inches(56.0 cm)

22 inches(56.0 cm)

*AC part number

**GM part number

�A1518C high-capacity air cleaner filter may be substituted.

7-

yellowblue

7-1

Section 7 Maintenance Schedule

This section covers the maintenance required for your vehicle. Your vehicle needs these services to retain its safety,dependability and emission control performance.

7-2 Introduction7-4 Part A: Scheduled Maintenance Services7-5 Scheduled Maintenance7-18 Part B: Owner Checks and Services

7-23 Part C: Periodic Maintenance Inspections7-25 Part D: Recommended Fluids and Lubricants7-28 Part E: Maintenance Record

yellowblue

7-2

Have you purchased the GM Protection Plan? The Plansupplements your new vehicle warranties. See yourWarranty and Owner Assistance booklet, or your dealerfor details.

IntroductionYour Vehicle and the EnvironmentProper vehicle maintenance not only helps to keep yourvehicle in good working condition, but also helps theenvironment. All recommended maintenance proceduresare important. Improper vehicle maintenance can evenaffect the quality of the air we breathe. Improper fluidlevels or the wrong tire inflation can increase the levelof emissions from your vehicle. To help protect ourenvironment, and to keep your vehicle in goodcondition, please maintain your vehicle properly.

Maintenance RequirementsMaintenance intervals, checks, inspections andrecommended fluids and lubricants as prescribed in thismanual are necessary to keep your vehicle in goodworking condition. Any damage caused by failure tofollow recommended maintenance may not be coveredby warranty.

yellowblue

7-3

How This Section is OrganizedThis maintenance schedule is divided into five parts:

“Part A: Scheduled Maintenance Services” showswhat to have done and how often. Some of theseservices can be complex, so unless you are technicallyqualified and have the necessary equipment, you shouldlet your dealer’s service department or another qualifiedservice center do these jobs.

CAUTION:

Performing maintenance work on a vehicle canbe dangerous. In trying to do some jobs, you canbe seriously injured. Do your own maintenancework only if you have the required know-howand the proper tools and equipment for the job.If you have any doubt, have a qualifiedtechnician do the work.

If you want to get the service information, see “Serviceand Owner Publications” in the Index.

“Part B: Owner Checks and Services” tells you what should be checked and when. It also explains what you can easily do to help keep your vehicle ingood condition.

“Part C: Periodic Maintenance Inspections” explainsimportant inspections that your dealer’s servicedepartment or another qualified service center should perform.

“Part D: Recommended Fluids and Lubricants” listssome recommended products necessary to help keepyour vehicle properly maintained. These products, ortheir equivalents, should be used whether you do thework yourself or have it done.

“Part E: Maintenance Record” is a place for you to record and keep track of the maintenance performedon your vehicle. Keep your maintenance receipts. They may be needed to qualify your vehicle forwarranty repairs.

yellowblue

7-4

Part A: Scheduled Maintenance ServicesUsing Your Maintenance ScheduleWe at General Motors want to help you keep yourvehicle in good working condition. But we don’t knowexactly how you’ll drive it. You may drive very shortdistances only a few times a week. Or you may drivelong distances all the time in very hot, dusty weather.You may use your vehicle in making deliveries. Or you may drive it to work, to do errands or in manyother ways.

Because of all the different ways people use theirvehicles, maintenance needs vary. You may need morefrequent checks and replacements. So please read thefollowing and note how you drive. If you have anyquestions on how to keep your vehicle in goodcondition, see your dealer.

This part tells you the maintenance services you shouldhave done and when you should schedule them. If yougo to your dealer for your service needs, you’ll knowthat GM-trained and supported service people willperform the work using genuine GM parts.

The proper fluids and lubricants to use are listed in Part D. Make sure whoever services your vehicle usesthese. All parts should be replaced and all necessaryrepairs done before you or anyone else drives the vehicle.

This schedule is for vehicles that:

� carry passengers and cargo within recommendedlimits. You will find these limits on your vehicle’sCertification/Tire label. See “Loading Your Vehicle”in the Index.

� are driven on reasonable road surfaces within legaldriving limits.

� are driven off-road in the recommended manner. See“Off -Road Driving With Your Four-Wheel-DriveVehicle” in the Index.

� use the recommended fuel. See “Fuel” in the Index.

yellowblue

Scheduled Maintenance

7-5

The services shown in this schedule up to 100,000 miles(166 000 km) should be performed after 100,000 miles(166 000 km) at the same intervals. The services shownat 150,000 miles (240 000 km) and 200,000 miles (332 000 km) should be performed at the same intervals after 150,000 miles (240 000 km) and 200,000 miles (332 000 km).

See “Owner Checks and Services” and “PeriodicMaintenance Inspections” following.

Footnotes� The U.S. Environmental Protection Agency or theCalifornia Air Resources Board has determined that thefailure to perform this maintenance item will not nullifythe emission warranty or limit recall liability prior tothe completion of the vehicle’s useful life. We, however,urge that all recommended maintenance services beperformed at the indicated intervals and themaintenance be recorded.

+ A good time to check your brakes is during tirerotation. See “Brake System Inspection” under“Periodic Maintenance Inspections” in Part C of this schedule.

Scheduled Maintenance

yellowblue

7-6

Engine Oil and Chassis LubricationScheduled MaintenanceChange engine oil and filter as indicated by the GM OilLife System� (or every 12 months, whichever occursfirst). Reset the system. The system will show you whento change the oil -- usually between 3,000 miles (5 000 km) and 7,500 miles (12 500 km) since your lastoil change. Under severe conditions, the indicator maycome on before 3,000 miles (5 000 km). Never driveyour vehicle more than 7,500 miles (12 500 km) or 12 months without an oil and filter change.

The system won’t detect dust in the oil. So if you drivein a dusty area, be sure to change your oil and filterevery 3,000 miles (5 000 km) or sooner if the CHANGEENGINE OIL message appears. Remember to reset theOil Life System when the oil and filter have beenchanged. See “Oil Life System” in the Index forinformation on resetting.

An Emission Control Service.

Lubricate chassis components with each engine oil andfilter change. Lubricate the front suspension, ball joints,steering linkage, transmission shift linkage, transfer caseshift linkage, parking brake cable guides, and brakefront axle. Ball joints should not be lubricated unlesstheir temperature is 10�F (-12�C) or higher, or theycould be damaged.

yellowblue

Scheduled Maintenance

7-7

ENGINE OIL CHANGED

DATEACTUAL MILEAGE SERVICED BY:

ENGINE OIL CHANGED

DATEACTUAL MILEAGE SERVICED BY:

Scheduled Maintenance

yellowblue

7-8

ENGINE OIL CHANGED

DATEACTUAL MILEAGE SERVICED BY:

ENGINE OIL CHANGED

DATEACTUAL MILEAGE SERVICED BY:

yellowblue

Scheduled Maintenance

7-9

7,500 Miles (12 500 km)� Lubricate chassis components (or every 12 months, whichever occurs first).

(See footnote #.)� Check rear/front axle fluid level and add fluid as needed. Check constant

velocity joints and axle seals for leaking.� Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.)

15,000 Miles (25 000 km)� Lubricate chassis components (or every 12 months, whichever occurs first).

(See footnote #.)� If Equipped: Replace passenger compartment air filter. If you drive regularly

under dusty conditions, the filter may require replacement more often.� Check rear/front axle fluid level and add fluid as needed. Check constant

velocity joints and axle seals for leaking.� Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.)

ACTUAL SERVICED BY:MILEAGE

DATE

ACTUAL SERVICED BY:MILEAGE

DATE

Scheduled Maintenance

yellowblue

7-10

22,500 Miles (37 500 km)� Lubricate chassis components (or every 12 months, whichever occurs first).

(See footnote #.)� Check rear/front axle fluid level and add fluid as needed. Check constant

velocity joints and axle seals for leaking.� Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.)

30,000 Miles (50 000 km)� Lubricate chassis components (or every 12 months, whichever occurs first).

(See footnote #.)� If Equipped: Replace passenger compartment air filter. If you drive regularly

under dusty conditions, the filter may require replacement more often.� Check rear/front axle fluid level and add fluid as needed. Check constant

velocity joints and axle seals for leaking.� Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.) � Replace fuel filter.

An Emission Control Service. (See footnote�.)

ACTUAL SERVICED BY:MILEAGE

DATE

ACTUAL SERVICED BY:MILEAGE

DATE

yellowblue

Scheduled Maintenance

7-11

37,500 Miles (62 500 km)� Lubricate chassis components (or every 12 months, whichever occurs first).

(See footnote #.)� Check rear/front axle fluid level and add fluid as needed. Check constant

velocity joints and axle seals for leaking.� Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.)

45,000 Miles (75 000 km)� Lubricate chassis components (or every 12 months, whichever occurs first).

(See footnote #.)� If Equipped: Replace passenger compartment air filter. If you drive regularly

under dusty conditions, the filter may require replacement more often.� Check rear/front axle fluid level and add fluid as needed. Check constant

velocity joints and axle seals for leaking.� Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.)

ACTUAL SERVICED BY:MILEAGE

DATE

ACTUAL SERVICED BY:MILEAGE

DATE

Scheduled Maintenance

yellowblue

7-12

50,000 Miles (83 000 km)� Change automatic transmission fluid and filter if the vehicle is mainly driven

under one or more of these conditions:– In heavy city traffic where the outside temperature regularly reaches

90�F (32�C) or higher.– In hilly or mountainous terrain.– When doing frequent trailer towing.– Uses such as found in taxi, police or delivery service.If you do not use your vehicle under any of these conditions, change the fluidand filter at 100,000 miles (166 000 km).

52,500 Miles (87 500 km)� Lubricate chassis components (or every 12 months, whichever occurs first).

(See footnote #.)� Check rear/front axle fluid level and add fluid as needed. Check constant

velocity joints and axle seals for leaking.� Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.)

ACTUAL SERVICED BY:MILEAGE

DATE

ACTUAL SERVICED BY:MILEAGE

DATE

yellowblue

Scheduled Maintenance

7-13

60,000 Miles (100 000 km)� Lubricate chassis components (or every 12 months, whichever occurs first).

(See footnote #.)� If Equipped: Replace passenger compartment air filter. If you drive regularly

under dusty conditions, the filter may require replacement more often.� Check rear/front axle fluid level and add fluid as needed. Check constant

velocity joints and axle seals for leaking.� Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.) � Inspect engine accessory drive belt.

An Emission Control Service. � Replace fuel filter.

An Emission Control Service. (See footnote �.) � Inspect Exhaust Gas Recirculation (EGR) system as described in the

service manual. An Emission Control Service. (See footnote �.)

� Inspect Evaporative Control System. Check all fuel and vapor lines and hosesfor proper hook-up, routing and condition. Check that the purge valve worksproperly, if equipped. Replace as needed. An Emission Control Service. (See footnote �.)

ACTUAL SERVICED BY:MILEAGE

DATE

Scheduled Maintenance

yellowblue

7-14

67,500 Miles (112 500 km)� Lubricate chassis components (or every 12 months, whichever occurs first).

(See footnote #.)� Check rear/front axle fluid level and add fluid as needed. Check constant

velocity joints and axle seals for leaking.� Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.)

75,000 Miles (125 000 km)� Lubricate chassis components (or every 12 months, whichever occurs first).

(See footnote #.)� If Equipped: Replace passenger compartment air filter. If you drive regularly

under dusty conditions, the filter may require replacement more often.� Check rear/front axle fluid level and add fluid as needed. Check constant

velocity joints and axle seals for leaking.� Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.)

ACTUAL SERVICED BY:MILEAGE

DATE

ACTUAL SERVICED BY:MILEAGE

DATE

yellowblue

Scheduled Maintenance

7-15

82,500 Miles (137 500 km)� Lubricate chassis components (or every 12 months, whichever occurs first).

(See footnote #.)� Check rear/front axle fluid level and add fluid as needed. Check constant

velocity joints and axle seals for leaking.� Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.)

90,000 Miles (150 000 km)� Lubricate chassis components (or every 12 months, whichever occurs first).

(See footnote #.)� If Equipped: Replace passenger compartment air filter. If you drive regularly

under dusty conditions, the filter may require replacement more often.� Check rear/front axle fluid level and add fluid as needed. Check constant

velocity joints and axle seals for leaking.� Replace fuel filter.

An Emission Control Service. (See footnote �.) � Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.)

ACTUAL SERVICED BY:MILEAGE

DATE

ACTUAL SERVICED BY:MILEAGE

DATE

Scheduled Maintenance

yellowblue

7-16

97,500 Miles (162 500 km)� Lubricate chassis components (or every 12 months, whichever occurs first).

(See footnote #.)� Check rear/front axle fluid level and add fluid as needed. Check constant

velocity joints and axle seals for leaking.� Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.)

100,000 Miles (166 000 km)� Inspect spark plug wires.

An Emission Control Service. � Replace spark plugs.

An Emission Control Service.� Change automatic transmission fluid and filter if the vehicle is mainly driven

under one or more of these conditions:– In heavy city traffic where the outside temperature regularly reaches

90�F (32�C) or higher.– In hilly or mountainous terrain.– When doing frequent trailer towing.– Uses such as found in taxi, police or delivery service.

ACTUAL SERVICED BY:MILEAGE

DATE

ACTUAL SERVICED BY:MILEAGE

DATE

yellowblue

Scheduled Maintenance

7-17

� If you haven’t used your vehicle under severe service conditions listedpreviously and, therefore, haven’t changed your automatic transmission fluid,change both the fluid and filter.

� Inspect Positive Crankcase Ventilation (PCV) valve. An Emission Control Service.

150,000 Miles (240 000 km)� Drain, flush and refill cooling system (or every 60 months since last service,

whichever occurs first). See “Engine Coolant” in the Index for what to use.Inspect hoses. Clean radiator, condenser, pressure cap and neck. Pressure testthe cooling system and pressure cap. An Emission Control Service.

� Change five-speed manual transmission fluid (with 4300 V6 or 4800 V8 engines only).

200,000 Miles (332 000 km)� 6000 V8 Engine Only: Change five-speed manual transmission fluid.

ACTUAL SERVICED BY:MILEAGE

DATE

ACTUAL SERVICED BY:MILEAGE

DATE

yellowblue

7-18

Part B: Owner Checks and ServicesListed in this part are owner checks and services whichshould be performed at the intervals specified to helpensure the safety, dependability and emission controlperformance of your vehicle.

Be sure any necessary repairs are completed at once.Whenever any fluids or lubricants are added to yourvehicle, make sure they are the proper ones, as shown inPart D.

At Each Fuel FillIt is important for you or a service station attendant toperform these underhood checks at each fuel fill.

Engine Oil Level Check

Check the engine oil level and add the proper oil ifnecessary. See “Engine Oil” in the Index for further details.

Engine Coolant Level Check

Check the engine coolant level and add DEX-COOL�

coolant mixture if necessary. See “Engine Coolant” inthe Index for further details.

Windshield Washer Fluid Level Check

Check the windshield washer fluid level in thewindshield washer tank and add the proper fluid ifnecessary. See “Windshield Washer Fluid” in the Indexfor further details.

At Least Once a Month

Tire Inflation Check

Make sure tires are inflated to the correct pressures.Don’t forget to check your spare tire. See “Tires” in theIndex for further details.

Cassette Deck Service

Clean cassette deck. Cleaning should be done every 50 hours of tape play. See “Audio Systems” in the Indexfor further details.

yellowblue

7-19

At Least Twice a Year

Restraint System Check

Make sure the safety belt reminder light and all yourbelts, buckles, latch plates, retractors and anchorages areworking properly. Look for any other loose or damagedsafety belt system parts. If you see anything that mightkeep a safety belt system from doing its job, have itrepaired. Have any torn or frayed safety belts replaced.

Also look for any opened or broken air bag coverings,and have them repaired or replaced. (The air bag systemdoes not need regular maintenance.)

Wiper Blade Check

Inspect wiper blades for wear or cracking. Replace bladeinserts that appear worn or damaged or that streak ormiss areas of the windshield. Also see “Wiper Blades,Cleaning” in the Index.

Spare Tire Check

At least twice a year, after the monthly inflation checkof the spare tire determines that the spare is inflated tothe correct tire inflation pressure, make sure that thespare tire is stored securely. Push, pull, and then try torotate or turn the tire. If it moves, use the wheelwrench/hoist shaft to tighten the cable. See “Storing theSpare Tire and Tools” in the Index.

Engine Air Cleaner Filter Restriction Indicator Check

Your vehicle has an indicator located on the air cleanerin the engine compartment that lets you know when theair cleaner filter is dirty and needs to be changed. Checkindicator at least twice a year or when your oil ischanged, whichever occurs first. See “Air Cleaner” inthe Index for more information. Inspect your air cleanerfilter restriction indicator more often if the vehicle isused in dusty areas or under off road conditions.

Weatherstrip Lubrication

Silicone grease on weatherstrips will make them lastlonger, seal better, and not stick or squeak. Applysilicone grease with a clean cloth. During very cold,damp weather more frequent application may berequired. (See “Recommended Fluids and Lubricants” in the Index.)

yellowblue

7-20

Manual Transmission Check

Check the transmission fluid level; add if needed. See“Manual Transmission Fluid” in the Index. Check forleaks. A fluid leak is the only reason for fluid loss. Havethe system inspected and repaired if needed.

Automatic Transmission Check

Check the transmission fluid level; add if needed. See“Automatic Transmission Fluid” in the Index. A fluidloss may indicate a problem. Check the system andrepair if needed.

Hydraulic Clutch System Check

Check the fluid level in the clutch reservoir. See“Hydraulic Clutch Fluid” in the Index. A fluid loss inthis system could indicate a problem. Have the systeminspected and repaired at once.

At Least Once a Year

Key Lock Cylinders Service

Lubricate the key lock cylinders with the lubricantspecified in Part D.

Body Lubrication Service

Lubricate all body door hinges, hood latch assembly,secondary latch, pivots, spring anchor, release pawl,tailgate hinge, tailgate linkage, tailgate handle pivotpoints, latch bolt, fuel door hinge, locks and folding seathardware. Part D tells you what to use. More frequentlubrication may be required when exposed to a corrosive environment.

yellowblue

7-21

Starter Switch Check

CAUTION:

When you are doing this check, the vehicle couldmove suddenly. If it does, you or others could beinjured. Follow the steps below.

1. Before you start, be sure you have enough roomaround the vehicle.

2. Firmly apply both the parking brake (see “ParkingBrake” in the Index if necessary) and the regular brake.NOTE: Do not use the accelerator pedal, and beready to turn off the engine immediately if it starts.

3. On automatic transmission vehicles, try to start theengine in each gear. The starter should work only inPARK (P) or NEUTRAL (N). If the starter works inany other position, your vehicle needs service.On manual transmission vehicles, put the shift leverin NEUTRAL (N), push the clutch down halfwayand try to start the engine. The starter should workonly when the clutch is pushed down all the way tothe floor. If the starter works when the clutch isn’tpushed all the way down, your vehicle needs service.

Automatic Transmission Shift Lock Control System Check

CAUTION:

When you are doing this check, the vehicle couldmove suddenly. If it does, you or others could beinjured. Follow the steps below.

1. Before you start, be sure you have enough roomaround the vehicle. It should be parked on a level surface.

2. Firmly apply the parking brake (see “Parking Brake”in the Index if necessary).

NOTE: Be ready to apply the regular brakeimmediately if the vehicle begins to move.

3. With the engine off, turn the key to the RUNposition, but don’t start the engine. Without applyingthe regular brake, try to move the shift lever out ofPARK (P) with normal effort. If the shift levermoves out of PARK (P), your vehicle needs service.

yellowblue

7-22

Ignition Transmission Lock Check

While parked, and with the parking brake set, try to turnthe ignition key to LOCK in each shift lever position.

� With an automatic transmission, the key should turnto LOCK only when the shift lever is in PARK (P).

� With a manual transmission, the key should turn toLOCK only when you press the key release button.

On all vehicles, the key should come out only in LOCK.

Parking Brake and Automatic Transmission PARK (P) Mechanism Check

CAUTION:

When you are doing this check, your vehiclecould begin to move. You or others could beinjured and property could be damaged. Makesure there is room in front of your vehicle in caseit begins to roll. Be ready to apply the regularbrake at once should the vehicle begin to move.

Park on a fairly steep hill, with the vehicle facingdownhill. Keeping your foot on the regular brake, set theparking brake.

� To check the parking brake’s holding ability: With the engine running and transmission inNEUTRAL (N), slowly remove foot pressure fromthe regular brake pedal. Do this until the vehicle isheld by the parking brake only.

� To check the PARK (P) mechanism’s holding ability:With the engine running, shift to PARK (P). Then release the parking brake followed by theregular brake.

Underbody Flushing Service

At least every spring, use plain water to flush anycorrosive materials from the underbody. Take care toclean thoroughly any areas where mud and other debriscan collect.

yellowblue

7-23

Part C: Periodic Maintenance InspectionsListed in this part are inspections and services whichshould be performed at least twice a year (for instance,each spring and fall). You should let your dealer’sservice department or other qualified service center dothese jobs. Make sure any necessary repairs arecompleted at once.

Proper procedures to perform these services may befound in a service manual. See “Service and OwnerPublications” in the Index.

Steering and Suspension InspectionInspect the front and rear suspension and steeringsystem for damaged, loose or missing parts, signs ofwear or lack of lubrication. Inspect the power steeringlines and hoses for proper hook-up, binding, leaks,cracks, chafing, etc.

Exhaust System InspectionInspect the complete exhaust system. Inspect the bodynear the exhaust system. Look for broken, damaged,missing or out-of-position parts as well as open seams,holes, loose connections or other conditions which couldcause a heat build-up in the floor pan or could letexhaust fumes into the vehicle. See “Engine Exhaust” inthe Index.

Engine Cooling System InspectionInspect the hoses and have them replaced if they arecracked, swollen or deteriorated. Inspect all pipes,fittings and clamps; replace as needed. Clean the outsideof the radiator and air conditioning condenser. To helpensure proper operation, a pressure test of the coolingsystem and pressure cap is recommended at least once a year.

yellowblue

7-24

Throttle System InspectionInspect the throttle system for interference or binding,and for damaged or missing parts. Replace parts asneeded. Replace any components that have high effortor excessive wear. Do not lubricate accelerator andcruise control cables.

Drive Axle ServiceCheck rear/front axle fluid level and add as needed.Check constant velocity joints and axle seals for leaking.

Transfer Case (Four-Wheel Drive) InspectionEvery 12 months or at oil change intervals, check frontaxle and transfer case and add lubricant when necessary.On manual shift transfer case, oil the control lever pivotpoint. Check vent hose at transfer case for kinks andproper installation. More frequent lubrication may berequired on off-road use.

Brake System InspectionInspect the complete system. Inspect brake lines andhoses for proper hook-up, binding, leaks, cracks,chafing, etc. Inspect disc brake pads for wear and rotorsfor surface condition. Inspect other brake parts,including calipers, parking brake, etc. You may need tohave your brakes inspected more often if your drivinghabits or conditions result in frequent braking.

yellowblue

7-25

Part D: Recommended Fluids and LubricantsNOTE: Fluids and lubricants identified below by name,part number or specification may be obtained from your dealer.

USAGE FLUID/LUBRICANT

Engine Oil Engine Oil with the AmericanPetroleum Institute Certified ForGasoline Engines starburst symbolof the proper viscosity. Todetermine the preferred viscosityfor your vehicle’s engine, see“Engine Oil” in the Index.

Engine Coolant 50/50 mixture of clean, drinkablewater and use only GMGoodwrench� DEX-COOL� orHavoline� DEX-COOL�

Coolant. See “Engine Coolant” inthe Index.

USAGE FLUID/LUBRICANT

Hydraulic Brake System

Delco Supreme 11� Brake Fluid(GM Part No. 12377967 orequivalent DOT-3 Brake Fluid).

WindshieldWasher Solvent

GM Optikleen� Washer Solvent(GM Part No. 1051515) or equivalent.

Hydraulic Clutch System

Hydraulic Clutch Fluid (GM Part No. 12345347 or equivalentDOT-3 Brake Fluid).

Power Steering System

GM Power Steering Fluid (GM Part No. 1052884 - 1 pint,1050017 - 1 quart, or equivalent).

ManualTransmission(5-Speed withLow Gear, RPO MW3)

GM Goodwrench SyntheticManual Transmission Fluid (GM Part No. 12346190 - 1 qt.) orequivalent SAE 75W-85 GL-4Gear Oil.

yellowblue

7-26

USAGE FLUID/LUBRICANT

ManualTransmission(5-Speed withoutLow Gear, RPO MG5)

Synchromesh Transmission Fluid(GM Part No. 12345349 or equivalent).

AutomaticTransmission

DEXRON�-III AutomaticTransmission Fluid.

Key LockCylinders

Multi -Purpose Lubricant,Superlube� (GM Part No. 12346241 or equivalent).

Floor Shift Linkage

Lubriplate� Lubricant Aerosol(GM Part No. 12346293 orequivalent) or lubricant meetingrequirements of NLGI # 2Category LB or GC-LB.

ChassisLubrication

Chassis Lubricant (GM Part No. 12377985 or equivalent) orlubricant meeting requirements of NLGI # 2, Category LB or GC-LB.

USAGE FLUID/LUBRICANT

Front Axle SAE 80W-90 Axle Lubricant (GMPart No. 1052271 or equivalent).

Rear Axle SAE 75W-90 Synthetic AxleLubricant (GM Part No. 12378261)or equivalent meeting GMSpecification 9986115.

Manual Transfer Case

DEXRON�-III AutomaticTransmission Fluid.

AutomaticTransfer Case

Automatic Transfer Case Fluid(GM Part No. 12378396).

Front AxlePropshaft Splineor One-PiecePropshaft Spline(Two-WheelDrive with Auto. Trans.)

Spline Lubricant, SpecialLubricant (GM Part No. 12345879) or lubricantmeeting requirements of GM 9985830.

Rear DrivelineCenter Spline

Chassis Lubricant (GM Part No. 12377985 or equivalent) orlubricant meeting requirements of NLGI # 2, Category LB or GC-LB.

yellowblue

7-27

USAGE FLUID/LUBRICANT

Hood LatchAssembly,Secondary Latch,Pivots, SpringAnchor andRelease Pawl

Lubriplate� Lubricant Aerosol(GM Part No. 12346293 orequivalent) or lubricant meetingrequirements of NLGI # 2,Category LB or GC-LB.

Hood Hinges Multi -Purpose Lubricant,Superlube� (GM Part No. 12346241 or equivalent).

Body DoorHinge Pins,Tailgate Hingeand Linkage,Folding Seat andFuel Door Hinge

Multi -Purpose Lubricant,Superlube� (GM Part No. 12346241 or equivalent).

USAGE FLUID/LUBRICANT

Tailgate HandlePivot Points,Hinges, LatchBolt and Linkage

Multi -Purpose Lubricant,Superlube� (GM Part No. 12346241 or equivalent).

WeatherstripConditioning

Dielectric Silicone Grease (GMPart No. 12345579 or equivalent).

WeatherstripSqueaks

Synthetic Grease with Teflon,Superlube� (GM Part No. 12371287 or equivalent).

yellowblue

7-28

Part E: Maintenance RecordAfter the scheduled services are performed, record thedate, odometer reading and who performed the servicein the boxes provided after the maintenance interval.Any additional information from “Owner Checks and

Services” or “Periodic Maintenance” can be added onthe following record pages. Also, you should retain allmaintenance receipts. Your owner information portfoliois a convenient place to store them.

Maintenance Record

DATEODOMETER

READING SERVICED BY MAINTENANCE PERFORMED

yellowblue

7-29

Maintenance Record

DATEODOMETER

READING SERVICED BY MAINTENANCE PERFORMED

yellowblue

7-30

Maintenance Record

DATEODOMETER

READING SERVICED BY MAINTENANCE PERFORMED

8-

yellowblue

8-1

Section 8 Customer Assistance Information

Here you will find out how to contact GMC if you need assistance. This section also tells you how to obtain servicepublications and how to report any safety defects.

8-2 Customer Satisfaction Procedure8-4 Customer Assistance for Text Telephone

(TTY) Users8-4 Customer Assistance Offices8-5 GM Mobility Program for Persons

with Disabilities8-6 Roadside Assistance8-7 Canadian Roadside Assistance8-8 Courtesy Transportation

8-9 Warranty Information8-10 Reporting Safety Defects to the United

States Government8-10 Reporting Safety Defects to the

Canadian Government8-11 Reporting Safety Defects to General Motors8-11 Ordering Service and Owner Publications

in Canada

yellowblue

8-2

Customer Satisfaction Procedure Your satisfaction and goodwill are important to yourdealer and to GMC. Normally, any concerns with thesales transaction or the operation of your vehicle will beresolved by your dealer’s sales or service departments.Sometimes, however, despite the best intentions of allconcerned, misunderstandings can occur. If yourconcern has not been resolved to your satisfaction, thefollowing steps should be taken:

STEP ONE -- Discuss your concern with a member ofdealership management. Normally, concerns can bequickly resolved at that level. If the matter has alreadybeen reviewed with the sales, service or parts manager,contact the owner of the dealership or the general manager.

yellowblue

8-3

STEP TWO -- If after contacting a member of dealership management, it appears your concern cannot beresolved by the dealership without further help, contact the GMC Consumer Relations Manager by calling1-800-GMC-8782 (1-800-462-8782, Customer Assistanceprompt). In Canada, contact GM of Canada CustomerCommunication Centre in Oshawa by calling1-800-263-3777 (English) or 1-800-263-7854 (French).

We encourage you to call the toll-free number in orderto give your inquiry prompt attention. Please have thefollowing information available to give the CustomerAssistance Representative:

� Vehicle Identification Number (This is availablefrom the vehicle registration or title, or the plate at the top left of the instrument panel and visiblethrough the windshield.)

� Dealership name and location

� Vehicle delivery date and present mileage

When contacting GMC, please remember that yourconcern will likely be resolved at a dealer’s facility. Thatis why we suggest you follow Step One first if you havea concern.

STEP THREE -- Both General Motors and your dealerare committed to making sure you are completelysatisfied with your new vehicle. However, if youcontinue to remain unsatisfied after following theprocedure outlined in Steps One and Two, file with theGM/BBB Auto Line Program to enforce any additionalrights you may have. Canadian owners refer to yourWarranty and Owner Assistance Information booklet forinformation on the Canadian Motor Vehicle ArbitrationPlan (CAMVAP).

yellowblue

8-4

The BBB Auto Line Program is an out of court programadministered by the Council of Better Business Bureaus tosettle automotive disputes regarding vehicle repairs or theinterpretation of the New Vehicle Limited Warranty.Although you are required to resort to this informal disputeresolution program prior to filing any court action, use ofthe program is free of charge and your case will generallybe heard within 40 days. If you do not agree with thedecision given in your case, you may reject it and proceedwith any other venue for relief available to you.

You may contact the BBB using the toll-free telephonenumber or write them at the following address:

BBB Auto LineCouncil of Better Business Bureaus, Inc.4200 Wilson BoulevardSuite 800Arlington, VA 22203-1804

Telephone: 1-800-955-5100

This program is available in all 50 states and the Districtof Columbia. Eligibility is limited by vehicle age,mileage and other factors. General Motors reserves theright to change eligibility limitations and/or discontinueits participation in this program.

Customer Assistance for TextTelephone (TTY) UsersTo assist customers who are deaf, hard of hearing, or speech-impaired and who use Text Telephones(TTYs), GMC has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with GMC by dialing:1-800-GMC-8583 (462-8583). (TTY users in Canada can dial 1-800-263-3830.)

Customer Assistance OfficesGMC encourages customers to call the toll-free numberfor assistance. If a U.S. customer wishes to write to GMC,the letter should be addressed to GMC’s CustomerAssistance Center.

United StatesPontiac-GMC Customer Assistance CenterP.O. Box 436008Pontiac, MI 48343-6008

1-800-GMC-8782 (462-8782)1-800-GMC-8583 (462-8583) (For Text Telephone devices (TTYs))Roadside Assistance: 1-800-GMC-8782 (462-8782)

yellowblue

8-5

CanadaGeneral Motors of Canada LimitedCustomer Communication Centre, 163-0051908 Colonel Sam DriveOshawa, Ontario L1H 8P7

1-800-263-3777 (English)1-800-263-7854 (French)1-800-263-3830 (For Text Telephone devices (TTYs))Roadside Assistance: 1-800-268-6800

All Overseas LocationsGMODC - Customer Communication Centre169-0071908 Colonel Sam DriveOshawa, Ontario L1H 8P7

Telephone: 905-644-4112Fax: 905-644-4866

Caribbean Numbers1-800-496-9992 (English) Puerto Rico1-800-496-9993 (Spanish) Puerto Rico1-800-751-4135 (English) Dominican Republic1-800-751-4136 (Spanish) Dominican Republic1-800-496-9994 U.S. Virgin Islands1-800-389-0009 Bahamas1-800-534-0122 Bermuda, Barbados, Antigua & B.V.I.

If toll free service is not available in the Caribbean, call Puerto Rico 1-787-763-1315.

GM Mobility Program for Personswith Disabilities

This program, available toqualified applicants, canreimburse you up to $1,000toward aftermarket driver orpassenger adaptiveequipment you may requirefor your vehicle (handcontrols, wheelchair/scooterlifts, etc.).

This program can also provide you with free resourceinformation, such as area driver assessment centers andmobility equipment installers. The program is availablefor a limited period of time from the date of vehiclepurchase/lease. See your dealer for more details or callthe GM Mobility Assistance Center at 1-800-323-9935.Text telephone (TTY) users, call 1-800-833-9935.

GM of Canada also has a Mobility Program. Call1-800-GM-DRIVE (463-7483) for details. When calling from outside Canada, please dial 1-905-644-3063.All TTY users call 1-800-263-3830.

yellowblue

8-6

Roadside Assistance

GMC’s Roadside Assistance provides stranded ownerswith over-the-phone roadside repairs, location of thenearest GMC dealer or the following special services:

Flat Tire Change: Installation of spare tire will becovered at no charge (customer is responsible for repairor replacement of tire).

Fuel Delivery: Delivery of enough fuel for the customerto get to the nearest service station (up to $4.00) will be covered.

Jump Start: No-start situations which require a batteryjump start will be covered at no charge.

Lock Out: Replacement keys or locksmith service willbe covered at no charge if you are unable to gain entryinto your vehicle. Delivery of the replacement key willbe covered at no charge within 10 miles (16 km).

Emergency Towing Service: Towing to the nearest GMC dealer for warranty related disablements will be covered.

Deluxe Trip Routing: Custom-made, computerizedhighlighted maps using the most direct or scenic routeare provided free of charge. Maps include points ofinterest and a list of GMC dealers along the route. Alsoincluded is a list of hotels along the route that arediscounted through affiliation with “QuestInternational.” Trip Routing is available throughRoadside Assistance by calling 1-800-GMC-8782(462-8782). Please be prepared to provide your VehicleIdentification Number (VIN). Allow five working daysfor fulfillment.

yellowblue

8-7

Trip Interruption Assistance: GMC will reimburse anyreasonable trip interruption expenses (up to $500.00)when directly associated with warranty disablement. TripInterruption service covers expenses such as meals andovernight lodging if vehicle disablement occurs at least150 miles (240 km) from your home or rental property.Please Note: you will be required to obtain prior approval from GMC Roadside Assistance and pay forexpenses at the time of disablement. Original receiptsshould be submitted to GMC Roadside Assistance forreimbursement. A service representative will provideassistance when you call.

The Roadside Assistance services listed are available to retail and retail lease customers operating 2000 GMClight duty trucks for a period of 3 years/36,000 miles(60 000 km). All services must be pre-arranged byGMC Roadside Assistance.

Over-the-phone assistance, such as providing the nameof the closest dealer or minor technical advice, etc., isavailable to all owner/operators of GMC trucks,regardless of vehicle or mileage.

Just dial GMC Roadside Assistance at1-800-GMC-8782 (1-800-462-8782, RoadsideAssistance prompt) to reach a qualified representativewho can assist you.

Your Roadside Assistance representative will ask for thefollowing information when your call is received:

� Vehicle Identification Number (VIN)

� Name and home address

� Telephone number and location from which you are calling

� Location, license plate number and color of yourGMC truck

� Mileage of vehicle and description of problemRoadside Assistance is available 24 hours a day, 7 daysa week, 365 days a year, including weekends andholidays. Should you have any questions about roadsideassistance, call the GMC Roadside Assistance Center orcontact your dealer.Roadside Assistance is not part of or included in thecoverage provided by the New Vehicle Limited Warranty.GMC reserves the right to make any changes ordiscontinue the Roadside Assistance program at anytime without notification.

Canadian Roadside AssistanceVehicles purchased in Canada have an extensiveRoadside Assistance program accessible from anywherein Canada or the United States. Please refer to theseparate brochure provided by the dealer or call1-800-268-6800 for emergency services.

yellowblue

8-8

Courtesy TransportationGMC has always exemplified quality and value in itsoffering of motor vehicles. To enhance your ownershipexperience, we and our participating dealers are proud tooffer Courtesy Transportation, a customer supportprogram for new vehicles.

The Courtesy Transportation program is offered to retailpurchase/lease customers in conjunction with theBumper to Bumper coverage provided by the NewVehicle Limited Warranty. Several transportationoptions are available when warranty repairs arerequired. This will reduce your inconvenience duringwarranty repairs.

Plan Ahead When PossibleWhen your vehicle requires warranty service, youshould contact your dealer and request an appointment.By scheduling a service appointment and advising yourservice consultant of your transportation needs, yourdealer can help minimize your inconvenience. If yourvehicle cannot be scheduled into the service departmentimmediately, keep driving it until it can be scheduled forservice, unless, of course, the problem is safety-related.If it is, please call your dealership, let them know this,and ask for instructions.

If the dealer requests that you simply drop the vehicleoff for service, you are urged to do so as early in thework day as possible to allow for same day repair.

Transportation OptionsWarranty service can generally be completed while youwait. However, if you are unable to wait GMC helpsminimize your inconvenience by providing severaltransportation options. Depending on the circumstances,your dealer can offer you one of the following:

Shuttle Service

Participating dealers can provide you with shuttle service toget you to your destination with minimal interruption of your daily schedule. This includes a one way shuttle ride to a destination up to 10 miles from the dealership.

Public Transportation or Fuel Reimbursement

If your vehicle requires overnight warranty repairs,reimbursement up to $30 per day (five days maximum)may be available for the use of public transportationsuch as taxi or bus. In addition, should you arrangetransportation through a friend or relative,reimbursement for reasonable fuel expenses up to $10 per day (five day maximum) may be available.Claim amounts should reflect actual costs and besupported by original receipts.

yellowblue

8-9

Courtesy Rental Vehicle

When your vehicle is unavailable due to overnightwarranty repairs, your dealer may arrange to provideyou with a courtesy rental vehicle or reimburse you for arental vehicle you obtained, at actual cost, up to amaximum of $30.00 per day supported by receipts. This requires that you sign and complete a rentalagreement and meet state, local and rental vehicleprovider requirements. Requirements vary and mayinclude minimum age requirements, insurance coverage,credit card, etc. You are responsible for fuel usagecharges and may also be responsible for taxes, levies,usage fees, excessive mileage or rental usage beyond thecompletion of the repair.

Generally it is not possible to provide a like-vehicle as acourtesy rental.

Additional Program InformationCourtesy Transportation is available during theBumper-to-Bumper warranty coverage period, but it is not part of the New Vehicle Limited Warranty. A separate booklet entitled “Warranty and OwnerAssistance Information” furnished with each new vehicle provides detailed warranty coverage information.

Courtesy Transportation is available only atparticipating dealers and all program options, such asshuttle service, may not be available at every dealer.Please contact your dealer for specific information aboutavailability. All Courtesy Transportation arrangementswill be administered by appropriate dealer personnel.

Canadian Vehicles: For warranty repairs during theComplete Vehicle Coverage period of the GeneralMotors of Canada New Vehicle Limited Warranty,alternative transportation may be available under theCourtesy Transportation Program. Please consult yourdealer for details.

General Motors reserves the right to unilaterally modify, change or discontinue Courtesy Transportation at any time and to resolve all questions of claim eligibility pursuant to theterms and conditions described herein at its sole discretion.

Warranty InformationYour vehicle comes with a separate warranty bookletthat contains detailed warranty information.

yellowblue

8-10

REPORTING SAFETY DEFECTSTO THE UNITED STATESGOVERNMENTIf you believe that your vehicle has a defect which couldcause a crash or could cause injury or death, you shouldimmediately inform the National Highway TrafficSafety Administration (NHTSA), in addition tonotifying General Motors.

If NHTSA receives similar complaints, it may open aninvestigation, and if it finds that a safety defect exists ina group of vehicles, it may order a recall and remedycampaign. However, NHTSA cannot become involvedin individual problems between you, your dealer orGeneral Motors.

To contact NHTSA, you may either call the Auto SafetyHotline toll-free at 1-800-424-9393 (or 366-0123 in theWashington, D.C. area) or write to:

NHTSA, U.S. Department of TransportationWashington, D.C. 20590

You can also obtain other information about motorvehicle safety from the hotline.

REPORTING SAFETY DEFECTS TOTHE CANADIAN GOVERNMENTIf you live in Canada, and you believe that your vehiclehas a safety defect, you should immediately notifyTransport Canada, in addition to notifying GeneralMotors of Canada Limited. You may write to:

Transport Canada330 Sparks StreetTower COttawa, Ontario K1A 0N5

yellowblue

8-11

REPORTING SAFETY DEFECTSTO GENERAL MOTORSIn addition to notifying NHTSA (or Transport Canada)in a situation like this, we certainly hope you’ll notifyus. Please call us at 1-800-GMC-8782(1-800-462-8782), or write:

Pontiac-GMC Customer Assistance CenterP.O. Box 436008Pontiac, MI 48343-6008

In Canada, please call us at 1-800-263-3777 (English)or 1-800-263-7854 (French). Or, write:

General Motors of Canada LimitedCustomer Communication Centre, 163-0051908 Colonel Sam DriveOshawa, Ontario L1H 8P7

Ordering Service and OwnerPublications in CanadaService manuals, owner’s manuals and other serviceliterature are available for purchase for all current andpast model General Motors vehicles.

The toll-free telephone number for ordering informationin Canada is 1-800-668-5539.

yellowblue

8-12

CURRENT PUBLICATIONS FOR 2000 GMC

SERVICE MANUALSService Manuals have the diagnosis and repair informationon engines, transmission, axle, suspension, brakes,electrical, steering, body, etc.RETAIL SELL PRICE: $120.00

TRANSMISSION, TRANSAXLE, TRANSFER CASEUNIT REPAIR MANUALThis manual provides information on unit repair serviceprocedures, adjustments and specifications for the 2000 GM transmissions, transaxles and transfer cases.RETAIL SELL PRICE: $50.00

SERVICE BULLETINSService Bulletins give technical service information neededto knowledgeably service General Motors cars and trucks.Each bulletin contains instructions to assist in thediagnosis and service of your vehicle.

OWNER’S INFORMATIONOwner publications are written directly for Owners andintended to provide basic operational information about thevehicle. The owner’s manual will include the MaintenanceSchedule for all models.

In-Portfolio: Includes a Portfolio, Owner’s Manual andWarranty Booklet.RETAIL SELL PRICE: $20.00

Without Portfolio: Owner’s Manual only.RETAIL SELL PRICE: $15.00

CURRENT & PAST MODEL ORDER FORMSService Publications are available for current and pastmodel GM vehicles. To request an order form, pleasespecify year and model name of the vehicle.

PLEASE COMPLETE THE ORDER FORM SHOWN ONTHE FOLLOWING PAGE AND MAIL TO:

Helm, Incorporated � P.O. Box 07130 � Detroit, MI 48207

OR ORDER TOLL FREE: 1-800-551-4123Monday-Friday 8:00 AM – 6:00 PM Eastern Time

For Credit Card Orders Only (VISA–MasterCard–Discover)

2000 GMC SERVICE PUBLICATIONS ORDERING INFORMATION

The following publications covering the operation and servicing of your vehicle can be purchased by filling outthe Service Publication Order Form in this book and mailing it in with your check, money order,

or credit card information to Helm, Incorporated (address below.)

yellowblue

8-13

PUBLICATION FORMNUMBER

Orders will be mailed within 10 days of receipt. Please allow adequate time for postalservice. If further information is needed, write to the address shown below or call1-800-551-4123. Material cannot be returned for credit without packing slip with returninformation within 30 days of delivery. On returns, a re-stocking fee may be appliedagainst the original order.

ORDER TOLL FREE(NOTE: For Credit Card Holders Only)

1-800-551-4123(Monday-Friday 8:00 AM – 6:00 PM EST)

FAX Orders Only 1-313-865-5927

Service Manual

NOTE: Dealers and Companies please provide dealer or company name, and also thename of the person to whose attention the shipment should be sent. Mail completed order form to:

HELM, INCORPORATED � P.O. Box 07130 � Detroit, MI 48207For purchases outside U.S.A. please write to the above address for quotation.

2000 $120.00

2000 $50.00

2000 $20.00

2000 $15.00

TOTAL MATERIAL

Michigan Purchasers

U.S. Order Processing $6.00Canadian Postage

GRAND TOTAL

add 6% sales tax

(See Note Below)

GM-GMC-ORD99 *(Prices are subject to change without notice and without incurringobligation. Allow ample time for delivery.)

Note to Canadian Customers: All listed prices are quoted in U.S. funds. Canadian residentsare to make checks payable in U.S. funds. To cover Canadian postage, add $11.50 plus theU.S. order processing.

(CUSTOMER’S NAME) (ATTENTION)

(STREET ADDRESS—NO P.O. BOX NUMBERS)

(CITY) (ZIP CODE)

DAYTIME TELEPHONE NO.

(STATE)

AREA CODE

( )

PCheck or Money Order payable to

Helm, Inc. (USA fundsonly — do not send cash.)

VISA

Discover

AccountNumber:

ExpirationDate mo/yr:

CUSTOMER SIGNATURE

S

ITEM DESCRIPTIONNAME YEAR

VEHICLE MODEL QTY. PRICEEACH*

TOTALPRICE2

000

GM

HIP TO

AYMENT

Owner’s Manual Without Portfolio

Owner’s Manual In Portfolio

Car & Light TruckTransmission Unit Repair

MasterCard

Check here if your billing address is different from your shipping address shown.

PUBLICATION FORMNUMBER