2000 - 2013 Passenger Car Child Restraint Passenger Safety … · 2016. 12. 1. · Rear-Facing Car...

2000–2013 PASSENGER CAR CHILD PASSENGER SAFETYSUPPLEMENT

Chrysler/Dodge/Fiat/Plymouth/SRT

©2015 FCA US LLC. All Rights Reserved.

Chrysler, Dodge, Fiat, Plymouth and SRT are registered trademarks of FCA US LLC.

TABLE OF CONTENTSSECTION PAGE

1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2 INSTALLING CHILD RESTRAINTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3 INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE — CHRYSLER . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4 INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE — DODGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

5 INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE — FIAT / PLYMOUTH / SRT . . . . . . . . . . . . . . 87

6 INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

INTRODUCTION

CONTENTS

� Welcome From FCA US LLC. . . . . . . . . . . . . . . . . . .3

� How To Use This Supplement. . . . . . . . . . . . . . . . . .3

2 INTRODUCTION

Welcome From FCA US LLC

If you have opened this guide, chances are you havequestions about the correct use of child restraints in yourvehicle. This supplement has been developed to help an-swer those questions. This document is intended to supple-ment the information provided in the Owner’s Manualand/or User Guide that came with your vehicle. If you nolonger have your Owner’s Manual or User Guide, pleasevisit www.techauthority.com to order a replacement.

This guide does not cover the proper selection of car seats orthe proper usage of car seats. For questions about car seatselection and usage, please visit NHTSA’s website: http://www.safercar.gov/parents/Car-Seat-Safety.htm. Thiswebsite also features videos showing step-by-step instal-lation of different types of car seats.

How To Use This Supplement

The first chapter of this supplement, “Installing ChildRestraints,” provides general information about the instal-lation of child restraints in vehicles. It provides step-by-stepinstructions for installing a car seat using either the seatbelts or the LATCH anchorages in your vehicle. Read thissection to learn how to:

• Locate LATCH and Tether anchorages in vehicles

• Install a car seat using LATCH

• Install a car seat using seat belts

This section also includes key warnings about the misuse ofcar seats. Read and follow all of these warnings whentransporting children in your vehicle.

The remaining chapters provide information that is specificfor the Brand, Model and Model Year of your vehicle. To usethis section, first refer to the table of contents to find yourvehicle. Some listings will include a range of model years.Click on the section for your vehicle to find informationabout:

• Locating the LATCH anchorages in your vehicle

• Frequently asked questions about LATCH

• Directions for locating and using the Tether Anchoragesin your vehicle

• Seat belt systems in your vehicle for installing car seats

• Frequently asked questions about seat belts and car seats

Copyright ©2015 FCA US LLC

INTRODUCTION 3

www.techauthority.com

http://www.safercar.gov/parents/Car-Seat-Safety.htm

http://www.safercar.gov/parents/Car-Seat-Safety.htm

INSTALLING CHILD RESTRAINTS

CONTENTS

� Installing Child Restraints . . . . . . . . . . . . . . . . . . . .5

� Rear-Facing Car Seats And Air Bags . . . . . . . . . . . . .5

� Passenger Air Bag Disable (PAD) Indicator Light — IfEquipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

� Lower Anchors And Tethers For CHildren (LATCH)Restraint System . . . . . . . . . . . . . . . . . . . . . . . . . . .5

� Locating The LATCH And Tether Anchorages . . . . . .5

� Installing Child Restraints Using The LATCH LowerAnchorages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

� How To Stow An Unused ALR Seat Belt . . . . . . . . . .6

� Installing Child Restraints Using The VehicleSeat Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

� Installing A Child Restraint With A SwitchableAutomatic Locking Retractor (ALR) — If Equipped . .6

� Installing A Child Restraint With A Cinching LatchPlate (CINCH) — If Equipped . . . . . . . . . . . . . . . . .7

� Installing Child Restraints Using The Top TetherAnchorage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

4 INSTALLING CHILD RESTRAINTS

Installing Child Restraints

Children 12 years or younger should ride properly buckledup in a rear seat, if available. According to crash statistics,children are safer when properly restrained in the rear seatsrather than in the front.

Every state in the United States and all Canadian provincesrequire that small children ride in proper restraint systems.This is the law, and you can be prosecuted for ignoring it.

NOTE: For additional information, refer to www.seatcheck.orgor call 1-866-SEATCHECK. Canadian residents shouldrefer to Transport Canada’s website for additional infor-mation: http://www.tc.gc.ca/eng/motorvehiclesafety/safedrivers-childsafety-index-53.htm

Rear-Facing Car Seats And Air Bags

WARNING!

• Never place a rear-facing child restraint in front of anair bag. A deploying passenger Advanced Front AirBag can cause death or serious injury to a child 12years or younger, including a child in a rear-facingchild restraint.

• Only use a rear-facing child restraint in a vehicle witha rear seat.

Passenger Air Bag Disable (PAD) Indicator Light —If Equipped

The PAD is an amber light located in the instrument panelwhich tells the driver and front passenger when the frontpassenger air bag is turned off. The PAD indicator lightilluminates to show that the passenger air bag will notinflate during a collision requiring air bags. The PAD lightwill illuminate when the passenger frontal air bag has beenturned off by using the manual ON/OFF switch. Refer toyour Owner’s Manual for additional information.

Lower Anchors And Tethers For CHildren (LATCH)Restraint System

Your vehicle is equipped with the child restraint anchoragesystem called LATCH, which stands for Lower Anchors andTethers for CHildren. The LATCH system has three vehicleanchor points for installing LATCH-equipped child seats.

There are two lower anchorages located at the back of theseat cushion where it meets the seatback and one top tetheranchorage located behind the seating position. These an-chorages are used to install LATCH-equipped child seatswithout using the vehicle’s seat belts. Some seating posi-tions may have a top tether anchorage but no lower anchor-ages. In these seating positions, the seat belt must be usedwith the top tether anchorage to install the child restraint.

NOTE: The LATCH system was phased into vehicles duringthe 2000–2002 model years. Certain 2000 and 2001 modelyear vehicles did not feature lower anchorages. Thesevehicles had tether anchorages only. See the section“LATCH and Tethers in Your Vehicle” for more information.

Locating The LATCH And Tether Anchorages

The lower anchorages are round bars that are found at therear of the seat cushion where it meets the seat-back. If the bars are not readily visible, they arelocated below the anchorage symbols on the seat-back (if equipped). You will easily feel them if yourun your finger along the gap between the seat-

back and seat cushion.

There are tether strap anchorages behind the rearseating positions located in the panel between therear seatback and the rear window. They arefound under a plastic cover with the tether an-

chorage symbol on it. Vehicles that do not have this panelwill have tether anchorages located on the back of the seator near the floor. See the section “LATCH and Tethers inYour Vehicle” for more information about finding tethers inyour vehicle, as some may be hidden behind a panel orcover.

Always follow the directions of the child restraint manufac-turer when installing your child restraint. Not all childrestraint systems will be installed as described here.

Installing Child Restraints Using The LATCH LowerAnchorages

1. If the selected seating position has a Switchable Auto-matic Locking Retractor (ALR) seat belt, stow the seatbelt, following the instructions below. See the section“Seat Belt Systems in Your Vehicle” to check what type ofseat belt each seating position has.

2. Loosen the adjusters on the lower straps and on thetether strap of the child seat so that you can more easilyattach the hooks or connectors to the vehicle anchorages.

3. Place the child seat between the lower anchorages forthat seating position. For some second row seats, youmay need to recline the seat and/or raise the headrestraint to get a better fit. If the rear seat can be movedforward and rearward in the vehicle, you may wish tomove it to its rear-most position to make room for thechild seat. You may also move the front seat forward toallow more room for the child seat.

INSTALLING CHILD RESTRAINTS 5

www.seatcheck.org

http://www.tc.gc.ca/eng/motorvehiclesafety/safedrivers-childsafety-index-53.htm

http://www.tc.gc.ca/eng/motorvehiclesafety/safedrivers-childsafety-index-53.htm

4. Attach the lower hooks or connectors of the child re-straint to the lower anchorages in the selected seatingposition.

5. If the child restraint has a tether strap, connect it to thetop tether anchorage. See the section “LATCH and Teth-ers in Your Vehicle” for directions to attach a tetheranchor.

6. Tighten all of the straps as you push the child restraintrearward and downward into the seat. Remove slack inthe straps according to the child restraint manufacturer’sinstructions.

7. Test that the child restraint is installed tightly by pullingback and forth on the child seat at the belt path. It shouldnot move more than 1 inch (25.4 mm) in any direction.

How To Stow An Unused ALR Seat Belt

When using the LATCH attaching system to install a childrestraint, stow all ALR seat belts that are not being used byother occupants or being used to secure child restraints. Anunused belt could injure a child if they play with it andaccidentally lock the seat belt retractor. Before installing achild restraint using the LATCH system, buckle the seat beltbehind the child restraint and out of the child’s reach. If thebuckled seat belt interferes with the child restraint installa-tion, instead of buckling it behind the child restraint, routethe seat belt through the child restraint belt path and thenbuckle it. Do not lock the seat belt. Remind all children inthe vehicle that the seat belts are not toys and that theyshould not play with them.

WARNING!

• Improper installation of a child restraint to theLATCH anchorages can lead to failure of the restraint.The child could be badly injured or killed. Follow thechild restraint manufacturer’s directions exactly wheninstalling an infant or child restraint.

• Child restraint anchorages are designed to withstandonly those loads imposed by correctly-fitted childrestraints. Under no circumstances are they to be usedfor adult seat belts, harnesses, or for attaching otheritems or equipment to the vehicle.

Installing Child Restraints Using The Vehicle SeatBelt

The seat belts in the passenger seating positions areequipped with either a Switchable Automatic Locking Re-tractor (ALR) or a cinching latch plate or both. Both types ofseat belts are designed to keep the lap portion of the seat belttight around the child restraint so that it is not necessary touse a locking clip.

The ALR retractor can be “switched” into a locked mode bypulling all of the webbing out of the retractor and then lettingthe webbing retract back into the retractor. If it is locked, theALR will make a clicking noise while the webbing is pulledback into the retractor. For additional information on ALR,

refer to the section “Seat Belt Systems in Your Vehicle.” Thecinching latch plate is designed to hold the lap portion of theseat belt tight when webbing is pulled tight and straightthrough a child restraint’s belt path.

When installing a forward-facing child restraint, always usethe tether anchor up to the maximum weight allowed. Seethe section “LATCH and Tethers in Your Vehicle” for moreinformation about LATCH weight limits.

Installing A Child Restraint With A SwitchableAutomatic Locking Retractor (ALR) — If Equipped

1. Place the child seat in the center of the seating position.For some second row seats, you may need to recline theseat and/or raise the head restraint to get a better fit. Ifthe rear seat can be moved forward and rearward in thevehicle, you may wish to move it to its rear-most positionto make room for the child seat. You may also move thefront seat forward to allow more room for the child seat.

2. Pull enough of the seat belt webbing from the retractor topass it through the belt path of the child restraint. Do nottwist the belt webbing in the belt path.

3. Slide the latch plate into the buckle until you hear a “click.”

4. Pull on the webbing to make the lap portion tight againstthe child seat.

5. To lock the seat belt, pull down on the shoulder part ofthe belt until you have pulled all the seat belt webbingout of the retractor. Then, allow the webbing to retractback into the retractor. As the webbing retracts, you willhear a clicking sound. This means the seat belt is now inthe Automatic Locking mode.

6. Try to pull the webbing out of the retractor. If it is locked,you should not be able to pull out any webbing. If theretractor is not locked, repeat step 5.

7. Finally, pull up on any excess webbing to tighten the lapportion around the child restraint while you push the childrestraint rearward and downward into the vehicle seat.

8. If the child restraint has a top tether strap and the seatingposition has a top tether anchorage, connect the tetherstrap to the anchorage and tighten the tether strap. Seethe section “LATCH and Tethers in Your Vehicle” fordirections to attach a tether anchor.


Any seat belt system will loosen with time, so check the beltoccasionally, and pull it tight if necessary.

WARNING!

Do not use the Automatic Locking Mode to restrainoccupants who are wearing the seat belt or children whoare using booster seats. The locked mode is only used toinstall rear-facing or forward-facing child restraints thathave a harness for restraining the child.

6 INSTALLING CHILD RESTRAINTS

Installing A Child Restraint With A Cinching LatchPlate (CINCH) — If Equipped

1. Place the child seat in the center of the seating position.For some second row seats, you may need to recline theseat and/or raise the head restraint to get a better fit. Ifthe rear seat can be moved forward and rearward in thevehicle, you may wish to move it to its rear-most positionto make room for the child seat. You may also move thefront seat forward to allow more room for the child seat.

2. Next, pull enough of the seat belt webbing from theretractor to pass it through the belt path of the childrestraint. Do not twist the belt webbing in the belt path.

3. Slide the latch plate into the buckle until you hear a“click.”

4. Finally, pull up on any excess webbing to tighten the lapportion around the child restraint while you push thechild restraint rearward and downward into the vehicleseat.

5. If the child restraint has a top tether strap and the seatingposition has a top tether anchorage, connect the tetherstrap to the anchorage and tighten the tether strap. Seethe section “LATCH and Tethers in Your Vehicle” fordirections to attach a tether anchor.


Any seat belt system will loosen with time, so check the beltoccasionally, and pull it tight if necessary.

If the buckle or the cinching latch plate is too close to the beltpath opening of the child restraint, you may have troubletightening the seat belt. If this happens, disconnect the latchplate from the buckle and twist the short buckle-end belt upto three full turns to shorten it. Insert the latch plate into thebuckle with the release button facing out, away from thechild restraint. Repeat steps 4 to 6, above, to complete theinstallation of the child restraint.

If the belt still cannot be tightened after you shorten thebuckle, disconnect the latch plate from the buckle, turn thebuckle around one half turn, and insert the latch plate intothe buckle again. If you still cannot make the child restraintinstallation tight, try a different seating position.

Installing Child Restraints Using The Top TetherAnchorage

See the section “LATCH and Tethers in Your Vehicle” forspecific instructions for using the tether anchorages in yourvehicle.

WARNING!

Do not attach a tether strap for a rear-facing car seat toany location in front of the car seat, including the seatframe or a tether anchorage. Only attach the tether strapof a rear-facing car seat to the tether anchorage that isapproved for that seating position, located behind thetop of the vehicle seat. See the section “LATCH andTethers in Your Vehicle” for the location of approvedtether anchorages in your vehicle.

WARNING!

• In a collision, an unrestrained child, even a tiny baby,can become a projectile inside the vehicle. The forcerequired to hold even an infant on your lap couldbecome so great that you could not hold the child, nomatter how strong you are. The child and others couldbe severely injured or killed. Any child riding in yourvehicle should be in a proper restraint for the child’ssize.

• Never place a rear-facing child restraint in front of anair bag. A deploying Passenger Advanced Front AirBag can cause death or serious injury to a child 12years or younger, including a child in a rear-facingchild restraint.

• Only use a rear-facing child restraint in a vehicle witha rear seat.

• Improper installation of a child restraint to theLATCH anchorages can lead to failure of an infant orchild restraint. The child could be severely injured orkilled. Follow the manufacturer’s directions exactlywhen installing an infant or child restraint.

• An incorrectly anchored tether strap could lead toincreased head motion and possible injury to thechild. Use only the anchor positions directly behindthe child seat to secure a child restraint top tetherstrap.

• If your vehicle is equipped with a split rear seat, makesure the tether strap does not slip into the openingbetween the seatbacks as you remove slack in thestrap.

INSTALLING CHILD RESTRAINTS 7

INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE —CHRYSLER

CONTENTS

� CHRYSLER 200 CONVERTIBLE, 2011–2013 . . . . . . . .9

▫ LATCH And Tethers In Your Vehicle . . . . . . . . . . .9

▫ Center Seat LATCH . . . . . . . . . . . . . . . . . . . . . .10

▫ Connecting The Top Tether Strap (With Either LowerAnchors Or Vehicle Seat Belt) . . . . . . . . . . . . . . .10

▫ Seat Belt Systems In Your Vehicle . . . . . . . . . . . . .11

� CHRYSLER 200 SEDAN, 2011–2013. . . . . . . . . . . . .12

▫ LATCH And Tethers In Your Vehicle . . . . . . . . . .12




� CHRYSLER 300, 2005–2013. . . . . . . . . . . . . . . . . . .15





� CHRYSLER 300M, 2000–2004 . . . . . . . . . . . . . . . . .18





� CHRYSLER CONCORDE, 2000–2004. . . . . . . . . . . .22





� CHRYSLER CROSSFIRE, 2004–2008 . . . . . . . . . . . .26




� CHRYSLER LHS, 2000–2001 . . . . . . . . . . . . . . . . . .28


▫ Connecting The Top Tether Strap (With The VehicleSeat Belt) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28


� CHRYSLER PT CRUISER CONVERTIBLE,2005–2008 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30





� CHRYSLER PT CRUISER SEDAN, 2001–2010. . . . . .33





� CHRYSLER SEBRING CONVERTIBLE, 2001–2006,2008–2010 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38





� CHRYSLER SEBRING COUPE, 2000–2005 . . . . . . . .42





� CHRYSLER SEBRING SEDAN, 2001–2010 . . . . . . . .45





8 INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE — CHRYSLER

CHRYSLER 200 CONVERTIBLE, 2011–2013

LATCH And Tethers In Your Vehicle

LATCH Positions For Installing Child Restraints In ThisVehicle

Locating The LATCH Lower Anchorages In ThisVehicle

Locating The Tether Anchorages In This Vehicle

There are tether strap anchorages behind eachrear seating position. Access ports to the tetheranchors are located in the panel between the rearseat and the rear window. The tether anchors are

underneath access covers in the carpet covering the back ofthe seat where you see the tether anchorage symbol.

Frequently Asked Questions About LATCHWhat is the weight limit (child’s weight + weight ofthe child restraint) for using the LATCH anchorage

system to attach the child restraint?

65 lbs(29.5 kg)

Use the LATCH anchorage system until the com-bined weight of the child and the child restraint is

65 lbs (29.5 kg). Use the seat belt alone instead of theLATCH anchorage system once the combined weight

is more than 65 lbs (29.5 kg).Can the LATCH anchorages and the seat belt beused together to attach a rear-facing or forward-

facing child restraint?

No Do not use the seat belt when you use the LATCHanchorage system to attach a rear-facing or forward-

facing child restraint.Can two child restraints be attached using a common

lower LATCH anchorage?No Never “share” a LATCH anchorage with two or

more child restraints.Can the rear-facing child restraint touch the back of

the front passenger seat?Yes The child seat may touch the back of the front pas-

senger seat if the child restraint manufacturer alsoallows contact. See your child restraint Owner’s

Manual for more information.Can the head restraints be removed? No

2011–2013 Model Years

• ALR — Switchable Automatic Locking Retractor

• Lower Anchorage Symbol (2 Anchorages Per Seat-ing Position)

• Top Tether Anchorage Symbol

Rear Seat LATCH Lower Anchorages (2011–2013 ModelYears)

Child Tether Access Port Cover (2011–2013 Model Years)A — Cover B — Tether Strap Hook

Child Tether Anchor (2011–2013 Model Years)C — Attaching Strap D — Tether Anchor

INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE — CHRYSLER 9

Center Seat LATCH

WARNING!

This vehicle does not have a center seating position. Donot use the center lower LATCH anchorages to install achild seat in the center of the back seat.

Connecting The Top Tether Strap (With Either LowerAnchors Or Vehicle Seat Belt)

When installing a forward-facing child restraint, alwayssecure the top tether strap, up to the tether anchor weightlimit, whether the child restraint is installed with the loweranchors or the vehicle seat belt.

1. If lowered, raise the convertible top. The convertible topmust be in the UP position to access the tether anchor.

2. Open the access port cover behind the seat where you areplacing the child restraint.

3. Push the tether strap and hook through the access portand down into the trunk. Route the tether strap toprovide the most direct path from the child seat to theanchor.

4. Open the access cover on the carpet covering the back ofthe seat and attach the tether strap hook to the anchor.

5. Remove slack in the tether strap according to the childrestraint manufacturer’s instructions.

WARNING!

• An incorrectly anchored tether strap could lead toincreased head motion and possible injury to thechild. Use only the anchorage position directly behindthe child seat to secure a child restraint top tetherstrap.


Child Tether Access Port Cover

A — Cover B — Tether Strap Hook

Child Tether Anchor

C — Attaching Strap D — Tether Anchor


Seat Belt Systems In Your Vehicle

Lap/Shoulder Belt Systems For Installing Child RestraintsIn This Vehicle

Frequently Asked Questions About Seat Belts And Car SeatsWhat is the weight limit (child’s weight + weightof the child restraint) for using the Tether Anchorwith the seat belt to attach a forward facing child

restraint?

65 lbs(29.5 kg)

The Tether Anchor can be used with the seat beltuntil the combined weight of the child and the

child restraint is 65 lbs (29.5 kg). Use the seat beltwithout the Tether Anchor once the combined

weight is more than 65 lbs (29.5 kg).Can the rear-facing child restraint touch the back

of the front passenger seat?Yes Contact between the front passenger seat and the

child restraint is allowed, if the child restraintmanufacturer also allows contact.

Can the head restraints be removed? NoCan the buckle stalk be twisted to tighten the seat

belt against the belt path of the child restraint?No Do not twist the buckle stalk in a seating position

with an ALR retractor.



• Lower Anchorage Symbol (2 Anchorages PerSeating Position)



CHRYSLER 200 SEDAN, 2011–2013





There are tether strap anchorages behind eachrear seating position located in the panel betweenthe rear seatback and the rear window. They arefound under a plastic cover with the tether an-

chorage symbol on it.



65 lbs(29.5 kg)

Use the LATCH anchorage system until the com-bined weight of the child and the child restraint is65 lbs (29.5 kg). Use the seat belt and tether anchorinstead of the LATCH system once the combined

weight is more than 65 lbs (29.5 kg).Can a child seat be installed in the center position

using the inner LATCH lower anchorages?Yes You can install child restraints with flexible lower

anchors in the center position. The inner anchoragesare 15.4 inches (392 mm) apart. Do not install child

restraints with rigid lower anchors in the center posi-tion.

Can the LATCH anchorages and the seat belt beused together to attach a rear-facing or forward-





more child restraints.





Rear Seat LATCH Lower Anchorages(2011–2013 Model Years)

Tether Strap Anchorages

Tether Anchorages

1 — Cover A — Tether Strap Hook3 — Attaching Strap B — Tether Anchor


Frequently Asked Questions About LATCHCan the rear-facing child restraint touch the back of




Center Seat LATCH

Do not install child restraints with rigid lower attachmentsin the center seating position. Only install this type of childrestraint in the outboard seating positions. Child restraintswith flexible, webbing mounted lower attachments can beinstalled in any rear seating position.

WARNING!

Never use the same lower anchorage to attach more thanone child restraint. If you are installing LATCH-compatible child restraints next to each other, you mustuse the seat belt for the center position. You can then useeither the LATCH anchors or the vehicle’s seat belt forinstalling child seats in the outboard positions. Pleaserefer to “Installing The LATCH-Compatible Child Re-straint System” for typical installation instructions.



1. Look behind the seating position where you plan toinstall the child restraint to find the tether anchorage. Youmay need to move the seat forward to provide betteraccess to the tether anchorage. If there is no top tetheranchorage for that seating position, move the childrestraint to another position in the vehicle if one isavailable.

2. Rotate or lift the cover to access the anchor directlybehind the seat where you are placing the child restraint.

3. Route the tether strap to provide the most direct path forthe strap between the anchor and the child seat. If yourvehicle is equipped with adjustable rear head restraints,raise the head restraint, and where possible, route thetether strap under the head restraint and between the twoposts. If not possible, lower the head restraint and passthe tether strap around the outboard side of the headrestraint.

4. Attach the tether strap hook of the child restraint to thetop tether anchorage as shown in the diagram.


WARNING!



Tether Anchorages






restraint?

Weight limitof the Child

Restraint

Always use the tether anchor when using the seatbelt to install a forward facing child restraint, upto the recommended weight limit of the child re-

straint.Can the rear-facing child restraint touch the back











CHRYSLER 300, 2005–2013




• CINCH — Cinching Latch Plate









65 lbs(29.5 kg)


weight is more than 65 lbs (29.5 kg).Can the LATCH anchorages and the seat belt beused together to attach a rear-facing or forward-









Tether Strap Anchorages (2005–2013 Model Years)



Frequently Asked Questions About LATCH2005–2006 Model Years

Can the rear-facing child restraint touch the back ofthe front passenger seat?

No Contact between the front passenger seat and a childrestraint can affect the passenger airbag suppressionsystem. See your Owner’s Manual for more informa-

tion.Can the head restraints be removed? No

2007–2010 Model YearsCan the rear-facing child restraint touch the back of







Manual for more information.Can the head restraints be removed? Yes Center Only.

Center Seat LATCH

If a child restraint installed in the center position blocks theseat belt webbing or buckle for the outboard position, do notuse that outboard position. If a child seat in the centerposition blocks the outboard LATCH anchors or seat belt, donot install a child seat in that outboard position.

WARNING!

Never use the same lower anchorage to attach more thanone child restraint. Please refer to “Installing TheLATCH-Compatible Child Restraint System” for typicalinstallation instructions.



1. Look behind the seating position where you plan to installthe child restraint to find the tether anchorage. You mayneed to move the seat forward to provide better access tothe tether anchorage. If there is no top tether anchorage forthat seating position, move the child restraint to anotherposition in the vehicle if one is available.


3. Route the tether strap to provide the most direct path forthe strap between the anchor and the child seat. If yourvehicle is equipped with adjustable rear head restraints,raise the head restraint, and where possible, route thetether strap under the head restraint and between the twoposts. If not possible, lower the head restraint and pass thetether strap around the outboard side of the head restraint.



WARNING!

• An incorrectly anchored tether strap could lead toincreased head motion and possible injury to the child.Use only the anchorage position directly behind thechild seat to secure a child restraint top tether strap.

• If your vehicle is equipped with a split rear seat, makesure the tether strap does not slip into the openingbetween the seatbacks as you remove slack in the strap.

Center Tether Attachment (2011-2013 Model Year):

1. Lower the adjustable center head restraint to the fulldown position.

2. Route the tether strap over the seatback and head re-straint.




3. Attach the tether strap hook of the child restraint to thecenter tether anchorage located in the panel between therear seatback and the rear window.





restraint?


Restraint


straint.2005–2006 Model Years

Can the rear-facing child restraint touch the backof the front passenger seat?

No Contact between the front passenger seat and achild restraint can affect the passenger airbag sup-

pression system. See your Owner’s Manual formore information.


belt against the belt path of the child restraint?Yes In positions with cinching latch plates (CINCH),

the buckle stalk may be twisted up to 3 full turns.Do not twist the buckle stalk in a seating position

with an ALR retractor.2007–2010 Model Years


Yes Contact between the front passenger seat and thechild restraint is allowed, if the child restraint

manufacturer also allows contact.Can the head restraints be removed? No

Can the buckle stalk be twisted to tighten the seatbelt against the belt path of the child restraint?

Yes In positions with cinching latch plates (CINCH),the buckle stalk may be twisted up to 3 full turns.Do not twist the buckle stalk in a seating position




manufacturer also allows contact.Can the head restraints be removed? Yes Center only.


No Do not twist the buckle stalk in a seating positionwith an ALR retractor.








CHRYSLER 300M, 2000–2004




2000–2001 Model Years (Front Bucket Seats)

2000–2001 Model Years (Front Bench Seat)






Rear Seat Has No LATCH Lower Anchorages(2000–2001 Model Years)






Frequently Asked Questions About LATCH2000–2001 Model Years (No Lower Anchorages)

2002–2004 Model YearsWhat is the weight limit (child’s weight + weight ofthe child restraint) for using the LATCH anchorage


65 lbs(29.5 kg)












Center Seat LATCH



WARNING!












WARNING!
















restraint?

65 lbs(29.5 kg)








the buckle stalk may be twisted up to 3 full turns.


CHRYSLER CONCORDE, 2000–2004




















65 lbs(29.5 kg)












Center Seat LATCH



WARNING!












WARNING!
















restraint?

65 lbs(29.5 kg)










CHRYSLER CROSSFIRE, 2004–2008




Locating The Tether Anchorage In This Vehicle

There is a tether strap anchorage behind thepassenger seat located on the back of the seat nearthe floor.



65 lbs(29.5 kg)








more child restraints. If the center position does nothave dedicated LATCH lower anchorages, use the

seat belt to install a child seat in the center positionnext to a child seat using the LATCH anchorages in

an outboard position.Can the head restraints be removed? No




Passenger Seat LATCH Lower Anchorages(2004–2008 Model Years)

Tether Strap Anchorage (2004–2008 Model Years)




1. Move the seatback fully forward.

2. Pass the child restraint tether hook over the top of theseat, through the strap near the top of the seat back, andattach it to the anchor bar behind the passenger seat,below the seatback.

3. After securing the tether hook to the bar, recline theseatback fully rearward and move the seat to its mostrearward position.

4. Install the child restraint and return the seatback to anupright position.

5. Remove slack from the tether strap according to the childrestraint manufacturer’s directions.

WARNING!

An incorrectly anchored tether strap could lead toincreased head motion and possible injury to the child.Use only the anchorage position directly behind thechild seat to secure a child restraint top tether strap.




restraint?

65 lbs(29.5 kg)



weight is more than 65 lbs (29.5 kg).Can the head restraints be removed? No









CHRYSLER LHS, 2000–2001







Connecting The Top Tether Strap (With The VehicleSeat Belt)

When installing a forward-facing child restraint, alwayssecure the top tether strap, up to the tether anchor weightlimit.














WARNING!






restraint?

65 lbs(29.5 kg)
















CHRYSLER PT CRUISER CONVERTIBLE, 2005–2008





To gain access to the anchorages, locate the childtether anchorage decals on the carpet behind therear seat head forms and use a small screwdriverto pry the carpet flap open. The carpet flap is

attached in two different places.



65 lbs(29.5 kg)










an outboard position.








Frequently Asked Questions About LATCH2005 Model Year


Yes The child seat may touch the back of the front pas-senger seat if the child restraint manufacturer also

allows contact. See your child restraint Owner’sManual for more information.

Can the head restraints be removed? No2006–2008 Model Years




Center Seat LATCH

WARNING!




1. Locate the tether anchorages, found behind the rear seathead form, in the convertible top storage area.

2. Find the child tether anchorage decals on the carpetbehind the rear seat head forms and use a small screw-driver to pry the carpet flap open. The carpet flap isattached in two different places.

3. Route the tether strap over the center of the rear seat headform and attach it to the top tether anchorage as shown inthe diagram.


WARNING!











Frequently Asked Questions About Seat Belts And Car Seats2005 Model Year

What is the weight limit (child’s weight + weightof the child restraint) for using the Tether Anchorwith the seat belt to attach a forward facing child

restraint?

65 lbs(29.5 kg)










restraint?

65 lbs(29.5 kg)




of the front passenger seat?No Contact between the front passenger seat and a

child restraint can affect the passenger airbag sup-pression system. See your Owner’s Manual for

more information.Can the head restraints be removed? No




CHRYSLER PT CRUISER SEDAN, 2001–2010





There are tether strap anchorages behind eachrear seating position located on the back of theseat.


2005 Model Year












65 lbs(29.5 kg)










an outboard position.2001–2004 Model Years




Can the head restraints be removed? No2005 Model Year

Can a child seat be installed in the center positionusing the inner LATCH lower anchorages?

Yes You can install child restraints with flexible loweranchors in the center position. The inner anchoragesare 15.3 inches (390 mm) apart. Do not install child






Can a child seat be installed in the center positionusing the inner LATCH lower anchorages?

Yes You can install child restraints with flexible loweranchors in the center position. The inner anchoragesare 15.3 inches (390 mm) apart. Do not install child






Center Seat LATCH



This vehicle is not designed to have three child restraintsinstalled with LATCH at the same time. You may useLATCH to install one child restraint in the center position, ortwo child restraints in the outboard positions. DO NOTinstall more than two child restraints using LATCH at thesame time.

WARNING!




WARNING!






3. Attach the tether strap hook of the child restraint to thetop tether anchorage.


WARNING!







Frequently Asked Questions About Seat Belts And Car Seats2001–2005 Model Years


restraint?

65 lbs(29.5 kg)











2005 Model Year









restraint?

65 lbs(29.5 kg)










CHRYSLER SEBRING CONVERTIBLE, 2001–2006, 2008–2010






There are tether strap anchorages behind eachrear seating position located in the bottom of theconvertible top well, behind the seat back. Theanchors are under the carpet cutouts marked with

this symbol.










Child Tether Anchor Location (2001–2006 Model Years)



There are tether strap anchorages behind eachrear seating position. Access ports to the tetheranchors are located in the panel between the rearseat and the rear window. The tether anchors are

underneath access covers in the carpet covering the back ofthe seat where you see the tether anchorage symbol.



65 lbs(29.5 kg)












Child Tether Anchor (2001–2006 Model Years)

1 — Tether Hook And Anchor 2 — Tether Strap

Child Tether Access Port Cover (2008–2010 Model Years)


Child Tether Anchor (2008–2010 Model Years)



Center Seat LATCH

WARNING!





1. Lift the carpet flap to expose the anchor directly behindthe seat where you are placing the child restraint.

2. Route the tether strap to provide the most direct path forthe strap between the anchor and the child seat.



1. If lowered, raise the convertible top. The convertible topmust be in the UP position to access the tether anchor.

2. Open the access port cover behind the seat where you areplacing the child restraint.

3. Push the tether strap and hook through the access portand down into the trunk. Route the tether strap toprovide the most direct path from the child seat to theanchor.

4. Open the access cover on the carpet covering the back ofthe seat and attach the tether strap hook to the anchor.


WARNING!



Child Tether Anchor Location

Hook And Anchor

1 — Hook 2 — Anchor

Child Tether Access Port Cover


Child Tether Anchor






restraint?

65 lbs(29.5 kg)








Yes In positions with cinching latch plates (CINCH),the buckle stalk may be twisted up to 3 full turns.

2008–2010 Model YearsCan the buckle stalk be twisted to tighten the seat











CHRYSLER SEBRING COUPE, 2000–2005















1 — Cover A — Tether Strap Hook2 — Attaching The Strap B — Tether Anchor





65 lbs(29.5 kg)



is more than 65 lbs (29.5 kg).Can a child seat be installed in the center position

using the inner LATCH lower anchorages?No Use the seat belt and tether anchor to install a child

seat in the center seating position.Can the LATCH anchorages and the seat belt beused together to attach a rear-facing or forward-









Center Seat LATCH


WARNING!

• Do not install a child restraint in the center positionusing the LATCH system. This position is not ap-proved for installing child seats using the LATCHattachments. You must use the seat belt and tetheranchor to install a child seat in the center seatingposition.

• Never use the same lower anchorage to attach morethan one child restraint. Please refer to “Installing TheLATCH-Compatible Child Restraint System” for typi-cal installation instructions.








Tether Strap Mounting



WARNING!






restraint?

65 lbs(29.5 kg)















CHRYSLER SEBRING SEDAN, 2001–2010


















What is the weight limit (child’s weight + weight ofthe child restraint) for using the LATCH anchorage


65 lbs(29.5 kg)














65 lbs(29.5 kg)




using the inner LATCH lower anchorages?Yes You can install child restraints with flexible lower an-

chors in the center position. The inner anchorages are15.4 inches (392 mm) apart. Do not install child re-

straints with rigid lower anchors in the center position.Can the LATCH anchorages and the seat belt beused together to attach a rear-facing or forward-










Tether Anchorages






65 lbs(29.5 kg)















Center Seat LATCH



WARNING!




WARNING!







3. Route the tether strap to provide the most direct path forthe strap between the anchor and the child seat. If yourvehicle is equipped with adjustable rear head restraints,raise the head restraint, and where possible, route thetether strap under the head restraint and between the twoposts. If not possible, lower the head restraint and pass thetether strap around the outboard side of the head restraint.



WARNING!





Tether Anchorages












restraint?

65 lbs(29.5 kg)








the buckle stalk may be twisted up to 3 full turns.2007–2010 Model Years


restraint?


Restraint









INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE —DODGE

CONTENTS

� DODGE AVENGER, 2008–2013 . . . . . . . . . . . . . . . .51





� DODGE CALIBER, 2007–2012. . . . . . . . . . . . . . . . .54





� DODGE CHALLENGER, 2008–2013 . . . . . . . . . . . .57





� DODGE CHARGER, 2006–2013 . . . . . . . . . . . . . . .60





� DODGE DART, 2013 . . . . . . . . . . . . . . . . . . . . . . .63





� DODGE INTREPID, 2000–2003 . . . . . . . . . . . . . . . .66





� DODGE MAGNUM, 2005–2008 . . . . . . . . . . . . . . .70





� DODGE NEON, 2000–2005. . . . . . . . . . . . . . . . . . .73





� DODGE STRATUS COUPE, 2000–2005 . . . . . . . . . .76





� DODGE STRATUS SEDAN, 2001–2006 . . . . . . . . . .79





� DODGE VIPER, 2000–2006, 2008–2010. . . . . . . . . . .83




50 INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE — DODGE

DODGE AVENGER, 2008–2013









65 lbs(29.5 kg)









facing child restraint.







Tether Anchorages


INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE — DODGE 51

Frequently Asked Questions About LATCHCan two child restraints be attached using a common






Center Seat LATCH


WARNING!









WARNING!



Tether Anchorages






restraint?


Restraint













DODGE CALIBER, 2007–2012








65 lbs(29.5 kg)













an outboard position.
















Center Seat LATCH


WARNING!





2. Route the tether strap to provide the most direct path forthe strap between the anchor and the child seat, routingit over the center of the head restraint.



WARNING!







Frequently Asked Questions About Seat Belts And Car Seats2007 Model Year


restraint?


Restraint








2008–2012 Model YearsWhat is the weight limit (child’s weight + weightof the child restraint) for using the Tether Anchorwith the seat belt to attach a forward facing child

restraint?


Restraint













DODGE CHALLENGER, 2008–2013















Tether Anchorages





65 lbs(29.5 kg)









an outboard position.Can the rear-facing child restraint touch the back of




Center Seat LATCH


WARNING!









Tether Anchorages



WARNING!






restraint?


Restraint


















DODGE CHARGER, 2006–2013













65 lbs(29.5 kg)

























Manual for more information.Can the head restraints be removed? Yes Center Only.

Center Seat LATCH


WARNING!









WARNING!



Center Tether Attachment (2011-2013 Model Year):

1. Lower the adjustable center head restraint to the fulldown position.

2. Route the tether strap over the seatback and head re-straint.




3. Attach the tether strap hook of the child restraint to thecenter tether anchorage located in the panel between therear seatback and the rear window.





restraint?


Restraint


straint.2006 Model Year


No Contact between the front passenger seat and achild restraint can affect the passenger airbag sup-

pression system. See your Owner’s Manual formore information.







manufacturer also allows contact.Can the head restraints be removed? No






manufacturer also allows contact.Can the head restraints be removed? Yes Center only.










DODGE DART, 2013









65 lbs(29.5 kg)









facing child restraint.

2013 Model Year




Rear Seat LATCH Lower Anchorages (2013 Model Year)





Frequently Asked Questions About LATCHCan two child restraints be attached using a common







Manual for more information.Can the head restraints be removed? Yes Yes, all may be removed.

Center Seat LATCH


WARNING!









WARNING!



Tether Anchorages






restraint?


Restraint





Can the head restraints be removed? Yes All head restraints may be removed.Can the buckle stalk be twisted to tighten the seat



2013 Model Year





DODGE INTREPID, 2000–2003




















65 lbs(29.5 kg)












Center Seat LATCH



WARNING!












WARNING!
















restraint?

65 lbs(29.5 kg)










DODGE MAGNUM, 2005–2008








65 lbs(29.5 kg)








more child restraints.2005–2006 Model Years










Rear Seat Tether Strap Anchorages(2005–2008 Model Years)






Can the head restraints be removed? No

Center Seat LATCH


WARNING!





2. Route the tether strap to provide the most direct path forthe strap between the anchor and the child seat, routingit over the center of the head restraint.



WARNING!





Rear Seat Tether Strap Mounting (2005–2008 Model Years)








restraint?

65 lbs(29.5 kg)











restraint?

65 lbs(29.5 kg)











DODGE NEON, 2000–2005




















65 lbs(29.5 kg)














Center Seat LATCH



This vehicle is not designed to have three child restraintsinstalled with LATCH at the same time. You may useLATCH to install one child restraint in the center position, ortwo child restraints in the outboard positions. DO NOTinstall more than two child restraints using LATCH at thesame time.

WARNING!










WARNING!






restraint?

65 lbs(29.5 kg)

















DODGE STRATUS COUPE, 2000–2005




















65 lbs(29.5 kg)




using the inner LATCH lower anchorages?No Use the seat belt and tether anchor to install a child

seat in the center seating position.Can the LATCH anchorages and the seat belt beused together to attach a rear-facing or forward-









Center Seat LATCH


WARNING!

• Do not install a child restraint in the center positionusing the LATCH system. This position is not ap-proved for installing child seats using the LATCHattachments. You must use the seat belt and tetheranchor to install a child seat in the center seatingposition.

• Never use the same lower anchorage to attach morethan one child restraint. Please refer to “Installing TheLATCH-Compatible Child Restraint System” for typi-cal installation instructions.











WARNING!






restraint?

65 lbs(29.5 kg)















DODGE STRATUS SEDAN, 2001–2006















Tether Anchorages






65 lbs(29.5 kg)














65 lbs(29.5 kg)
















Center Seat LATCH



WARNING!




WARNING!










WARNING!





Tether Anchorages










restraint?

65 lbs(29.5 kg)










DODGE VIPER, 2000–2006, 2008–2010












Passenger Seat Has No LATCH Lower Anchorages(2000–2002, 2008–2010 Model Years)

Passenger Seat LATCH Lower Anchorages (2003–2006Model Years)



There is a tether strap anchor located behind thechild tether access cover behind the passengerseat.




65 lbs(29.5 kg)






facing child restraint.Can the head restraints be removed? No



1. Move the seat forward.

2. Move the seatback to its full forward position.

3. Remove the child tether access cover by prying eitherside with a screwdriver or similar tool, as shown.

NOTE: While the child tether is in use, keep the access coverin a safe place so that it can be replaced after use of the childtether.

4. Pass the child restraint tether hook through either open-ing in the seatback underneath the head restraint.

5. Attach the tether hook to the anchor loop.

Child Seat Tether Access Cover

Child Seat Tether Anchor




6. Move the seat to its farthest rearward position. Applybody pressure to the seat to be sure the seat adjustershave latched.

7. Return the seatback to an upright position.


WARNING!





restraint?

65 lbs(29.5 kg)




Tether Hook













2005–2006, 2008–2010 Model YearsCan the buckle stalk be twisted to tighten the seat




INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE —FIAT / PLYMOUTH / SRT

CONTENTS

� FIAT 500/ABARTH, 2012–2013. . . . . . . . . . . . . . . .88





� PLYMOUTH NEON, 2000–2001 . . . . . . . . . . . . . . .90




� PLYMOUTH PROWLER, 2000–2002 . . . . . . . . . . . .92




� SRT VIPER, 2013 . . . . . . . . . . . . . . . . . . . . . . . . . .94




INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE — FIAT / PLYMOUTH / SRT 87

FIAT 500/ABARTH, 2012–2013





There are tether strap anchors located behind eachrear seatback, near the floor.



65 lbs(29.5 kg)












Manual for more information.Can the head restraints be removed? Yes Yes, all may be removed.





Rear Seat LATCH Lower Anchorages

Rear Seat Tether Anchors

88 INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE — FIAT / PLYMOUTH / SRT

Center Seat LATCH

WARNING!








WARNING!






restraint?


Restraint





Can the head restraints be removed? Yes Yes, all may be removedCan the buckle stalk be twisted to tighten the seat



Rear Seat Tether Strap Mounting






PLYMOUTH NEON, 2000–2001





















WARNING!






restraint?

65 lbs(29.5 kg)















PLYMOUTH PROWLER, 2000–2002





There is a tether strap anchor located behind thepassenger seat.



1. Move the seatback fully forward.

2. Pass the child restraint strap hook through the openingunder the head restraint. Attach the hook to the anchorloop, recline the seat back full rearward and move theseat to its most rearward position.

3. Install the child restraint according to the manufacturer’sdirections.

4. Return the seat back to an upright position.

5. Remove the slack from the tether strap according to thechild restraint manufacturer’s directions.

WARNING!






Passenger Seat Has No LATCH Lower Anchorages(2000–2002 Model Years)

Passenger Seat Tether Strap Anchorage

Passenger Seat Tether Strap Anchorages






restraint?

65 lbs(29.5 kg)







SRT VIPER, 2013





There is a tether strap anchor located behind thechild tether access cover behind the passengerseat.



1. Move the seat forward.

2. Move the seatback to its full forward position.

3. Remove the child tether access cover by prying eitherside with a screwdriver or similar tool, as shown.

NOTE: While the child tether is in use, keep the access coverin a safe place so that it can be replaced after use of the childtether.

2013 Model Year



Passenger Seat Has No LATCH Lower Anchorages(2013 Model Year)






4. Pass the child restraint tether hook through either open-ing in the seatback underneath the head restraint.

5. Attach the tether hook to the anchor loop.

6. Move the seat to its farthest rearward position. Applybody pressure to the seat to be sure the seat adjustershave latched.

7. Return the seatback to an upright position.


WARNING!





restraint?


Restraint


straint.Can the head restraints be removed? No



Tether Hook2013 Model Year




INDEX

Automatic Locking Retractor (ALR) . . . . . . . . . . . . . . . .6

Center Seat LATCH . . . .7, 10, 13, 16, 19, 23, 31, 35, 40, 43,47, 52, 55, 58, 61, 64, 67, 71, 74, 77, 80, 89

Child Restraints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Connecting The Top Tether Strap . .10, 13, 16, 19, 23, 27, 28,

31, 35, 40, 43, 48, 52, 55, 58, 61, 64, 67, 71,74, 77, 81, 84, 89, 90, 92, 94

Frequently Asked Questions About LATCH. . . . . . .12, 15,19, 23, 26, 28, 30, 33, 38, 42, 46, 51, 54,

57, 60, 63, 67, 70, 73, 76, 79, 84, 88, 90, 92, 94Frequently Asked Questions About Seat Belts And Car

Seats . . . . .11, 14, 17, 20, 24, 27, 29, 31, 36, 41, 44, 48, 53,56, 59, 62, 65, 68, 71, 75, 78, 81, 85, 89, 91, 92, 95

How To Stow An Unused ALR Seat Belt. . . . . . . . . . . . .6

Installing A Child Restraint With A CinchingLatch Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Installing A Child Restraint With ALR . . . . . . . . . . . . . .6Installing Child Restraints In Your Vehicle. . . . .1, 9, 51, 88Installing Child Restraints Using The LATCH Lower

Anchorages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Installing Child Restraints Using The Top Tether

Anchorage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Installing Child Restraints Using The Vehicle Seat Belt . . .6

LATCH And Tethers In Your Vehicle . . . . .9, 12, 15, 18, 22,26, 28, 30, 33, 38, 42, 45, 51, 54, 57,

60, 63, 66, 70, 73, 76, 79, 83, 88, 90, 92, 94LATCH Lower Anchorages . . . .9, 12, 15, 18, 22, 26, 28, 30,

33, 38, 42, 45, 51, 54, 57, 60, 63, 66,70, 73, 76, 79, 83, 88, 90, 92, 94

Locating The LATCH And TetherAnchorages. . . . . . . . . . . . . . . . . . . . . . . . . . .5, 9, 12,

15, 18, 22, 26, 28, 30, 33, 38, 42, 45, 51, 54,57, 60, 63, 66, 70, 73, 76, 79, 83, 88, 90, 92, 94

Lower Anchors And Tether For CHildren (LATCH) . . . . .5

Rear Facing Car Seats And Air Bags. . . . . . . . . . . . . . . .5

Seat Belt Systems In Your Vehicle . . . .11, 14, 17, 20, 24, 27,29, 31, 36, 41, 44, 48, 53, 56, 59, 62, 65, 68,

71, 75, 78, 81, 85, 89, 91, 92, 95

Top Tether Anchorages . . . . .7, 9, 10, 12, 13, 15, 16, 19, 23,26, 27, 28, 30, 31, 33, 35, 38, 40, 42,

43, 46, 48, 51, 52, 54, 55, 57, 58, 60, 61,63, 64, 67, 70, 71, 73, 74, 76, 77, 79,

81, 84, 88, 89, 90, 92, 94

96 INDEX

2000 - 2013 Passenger Car Child Restraint Passenger Safety … · 2016. 12. 1. · Rear-Facing Car...

Documents

Transcript of 2000 - 2013 Passenger Car Child Restraint Passenger Safety … · 2016. 12. 1. · Rear-Facing Car...