2. Brochure - McON Air
-
Upload
kenny-ruiz -
Category
Documents
-
view
53 -
download
7
description
Transcript of 2. Brochure - McON Air
Prozess- und Messtechnik Conrads GmbH
Steinfeldstr. 5D-39179 BarlebenGermany
Phone +49 (0)39203 512-0Fax +49 (0)39203 [email protected]
Maintenance freegas flow measurementfor hot and dusty media
Technical data
Measurement principle: cross correlationTypical accuracy: better +/- 2%Repeatability: better 0,05 %Drift: 0 %Maintenance/cleaning: noneLinearity: 100%Hysteresis: noneCalibration: noneGas temperature: 10 – 400/1100 °C std/ht (50 - 750/2000 °F std/ht)Dust load range: 1mg – 2000g/m3
Safety standards: SIL 2 according EN 61508 for McON air SIL
Enclosure type: Rittal AE1030.500Dimensions: 380x300x155 mm (15x12x6’’)
widthxheightxdepthMaterial: sheet steelMaterial option: stainless steel enclosure AE 1004.600Surface finish: powder coated RAL 7035Degree of protection: IP66, NEMA 4Weight: 10 kg (22 lbs)Mounting: wall mounting bracketsPower supply: 85 – 264 VAC, 47 - 63 Hz or 24 VDCPower consumption: max. 0,8 A (115 VAC)/0,4 A (230 VAC)Recommended circuit breaker: 10 A (characteristic C or slow blow fuse)Temperature range (operation): -20/0 – 55 °C (-4 /32 – 130 °F)Temperature range (storage): -20/0 – 65 °C (-4 /32 – 149 °F)I/Os: 1x4-20 mA, 2xrelay (error contact)
Dimensions and weights
Online gas flowmeasurement
Highly accurate
No calibration,no drift, no cleaning
Not affected evenby high dust levels
Works up to 1100 °C
SIL 2 version available
name
company
street
postal code
city
phone
For further informationplease send a fax to:
Fax: +49 (0)39203 512-202
PROMECONPROMECON
(or company stamp)
PROMECONPROMECON PROMECON GmbH GermanyPhone +49 (0)39203 [email protected]
power – cement – smelters
McONair McONair SIL/
BU-MOair-1.1-EN
Drift and calibration free gas flow measurement Our customers´ opinion:
Installation via flange without calibration of the sensors
Installation of McON air in power station
Installation via flange without calibration of the sensors
With McON airwe don´t have tokeep cleaning themeasurement system. I now know,
that our measurementvalues are always repeatablesince they don´t drift.
Since we´ve hadMcON air we don´thave to worry aboutrecalibrating.Commissioning is
dead simple anddoesn´t need calibration -truly plug & play.
In the past thechoice was:
A conditionaldelta P measurement
measures the mass flowaccurately only for a
limited time aftercleaning. Hence acyclical purging of
the pressure tabs is necessary.
In case of foulingthe delta P measurement
will remain inaccurateeven after cleaning.
McON air gives you:
McON air will alwaysremain accurate evenwith highest dust levelssince it is based on a pertime measurement - nocleaning even at highest
dust levels (2000g/m3).The actual flow is
measured without theuse of temperature and
pressure measurements.
In addition themeasurement alwaysmonitors the plausibilityof the raw signals.
0 days 1 day 2 days 3 days 4days 5 days
m3/h
delta Pmeasurement
purging purging purging purging purging
t