19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold 1 Lecture 6 Applications of...
-
Upload
annice-elliott -
Category
Documents
-
view
249 -
download
3
Transcript of 19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold 1 Lecture 6 Applications of...
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold 1
Lecture 6
Applications of Nuclear Physics
Fission Reactors and Bombs
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
2
6.1 Overview 6.1 Induced fission
Fissile nuclei Time scales of the fission process Crossections for neutrons on U and Pu Neutron economy Energy balance A simple bomb
6.2 Fission reactors Reactor basics
Moderation Control Thermal stability
Thermal vs. fast Light water vs. heavy water Pressurised vs. Boiling water Enrichment
6.3 Fission Bombs Fission bomb fuels Suspicious behaviour
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
3
6.1 Induced Fission
(required energy)
Neutrons
Ef=Energy needed to penetrate fission barrier immediately ≈6-8MeV
A=238
Neu
tron
Nucleus Potential Energy [MeV]
Esep≈6MeV per nucleon for heavy nuclei
Very slow n
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
4
6.1 Induced Fission
(required energy)
Spontaneous fission rates low due to high coulomb barrier (6-8 MeV @ A≈240)
Slow neutron releases Esep as excitation into nucleus
Excited nucleus has enough energy for immediate fission if Ef - Esep >0
But due to pairing term … even N nuclei have low Esep
odd N nuclei have high Esep Fission yield in n-absorption varies
dramatically between odd and even N
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
5
6.1 Induced Fission(fissile nuclei)
Esep(n,238U) = 4.78MeV only Fission of 238U needs En>Ef-Esep≈1.4 MeV Must be provided by n-kinetic energy Call this fast fission Thermally fissile nuclei, En
thermal=0.1eV @ 1160K 233
92U, 23592U, 239
94Pu, 24194Pu
Fast fissile nuclei En=O(MeV) 232
90Th, 23892U, 240
94Pu, 24294Pu
Note: all Pu isotopes on earth are man made Note: only 0.72% of natural U is 235U
19 Nov 2004, Lecture 6 6
6.1 Induced Fission (Reminder: stages of the process)
t=0
t≈10-14 s
t>10-10 s
<# prompt n>=2.5
<n-delay>d=few s
<# delayed n>d=0.006
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
7
6.1 Induced Fission (the fission process)
Energy balance in MeV: Prompt:
Ekin(fragments) 167 Ekin(prompt n’s) 5 3-12 from X+nY+ E(prompt ) 6 Subtotal: 178 (good for power
production) Delayed
Ekin(e from -decays) 8 E( following -decay) 7 Subtotal: 15 (bad, spent fuel heats up)
Neutrinos 12 (invisible) Grand total 205
8
6.1 Induced Fission(fission crossections)
23592U does O(85%) fission starting at very low En
23892U does nearly no fission below En≈1.4MeV
Consistent with SEMF-pairing term of 12MeV/√A≈0.8MeV between odd-even= 235
92U and even-even= 23892U
unre
solv
ed, n
arro
wre
sonance
s
unre
solv
ed, n
arro
wre
sonance
s
238U 235U
9
6.1 Induced Fission(fission probabilities in natural Uranium)
23592U(n,f)
23592U(n,)
23892U(n,) 238
92U(n,f)235
92U(n,f)
23592U(n,)
23892U(n,)
23892U(n,)
en
erg
y r
ange o
f fi
ssio
n n
eutr
on
s
fastthermal
ab
sorb
tion p
rob
abili
t per
1
m
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
10
6.1 Induced Fission(a simple bomb)
mean free path:
235 238(1 )tot tot totc c 1 ( ) 3 cmnucl totl
Simplify to c=1 (the bomb mixture) prob(235U(npromptf)) @ 2MeV ≈ 18% rest of n scatter, loosing Ekin prob(235U(n,f)) grows most probable #collisions before 235U(nf) = 6 (work it out!) 6 random steps of l=3cm lp=√6*3cm≈7cm in tp=10-8 s
Uranium mix 235U:238U =c:(1-c) nucl(U)=4.8*1028 nuclei m-3
average crossection:
mean time between collisions =1.5*10-9 s @ Ekin(n)=2MeV
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
11
6.1 Induced Fission(a simple bomb)
After 10-8 s 1n is replaced with =2.5 n Let probability of new n inducing fission before it is lost = q
(others escape or give radiative capture) Each n produces on average (q-1) new n’s in tp=10-8 s
(ignoring delayed n’s as bombs don’t last for seconds!)
0
( 1)
( ) ( ) ( 1) ( ) ( )
( ) 1lim ( )
solved by: ( ) (0) p
p
tp
tq t
n t t n t q n t t t
dn t qn t
dt t
n t n e
if q>1exponential growths For 235U, =2.5 if q>0.4 you get a bomb
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
12
6.1 Induced Fission(a simple bomb)
If object dimensions << 7cm most n’s escape through surface q << 1
If Rsphere(235U)≥8.7cm M(235U)≥52 kg
q = 1 explosion in < tp=10-8 s
little time for sphere to blow apart significant fraction of 235U will do fission
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
13
6.2 Fission Reactors(not so simple)
Q: What happens to a 2 MeV fission neutron in a block of natural Uranium (c=0.72%)?
A: In order of probability Inelastic 238U scatter Fission of 238U (5%) rest is negligible
Eneutron decreases (238
92U(n,)) increases and becomes resonant (238
92U(n,f)) dercreases rapidly and vanishes below 1.4 MeV only remaining change for fission is (235
92U(n,f)) wich is much smaller then (238
92U(n,)) Conclusion: piling up natural U won’t make a reactor. I
said it is not SO simple
23592U(n,f)
23592U(n,)
23892U(n,) 238
92U(n,f)235
92U(n,f)
23592U(n,)
23892U(n,)
23892U(n,)
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
14
6.2 Fission Reactors(two ways out)
Way 1: Thermal Reactors bring neutrons to thermal energies without
absorbing them = moderate them use low mass nuclei with low n-capture as
moderator material. (Why low mass?) sandwich fuel rods with moderator (and
coolant) layers when n return from moderator energy is so
low that it will predominantly cause fission in 235U
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
15
6.2 Fission Reactors(two ways out)
Way 2: Fast Reactors Use fast neutrons for fission Use higher fraction of fissile material,
typically 20% of 239Pu + 80% 238U This is self refuelling (breeding) via:
23892U+n 239
92U + 239
93Np + e- + e
23994Pu + e¯ + e
Details about fast reactors later
16
6.2 Fission Reactors (Pu fuel)
239Pu fission crossection slightly “better” then 235U Chemically separable from 238U (no centrifuges) More prompt neutrons (239Pu)=2.96 Fewer delayed n & higher n-absorbtion, more later
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
17
6.2 Fission Reactors (Reactor control)
For bomb we found: “boom” if: q > 1 where was number of prompt n
Reactors use control rods with large n-capture (B, Cd) to regulate q
Lifetime of prompt n: O(10-8 s) in pure 235U O(10-3 s) in thermal reactor (long time in
moderator) Far too fast to control … but there are also delayed n’s
18
6.2 Fission Reactors (Reactor control)
Fission products all n-rich all - active Daughters of some - decays can directly emit n’s (see
table of nuclides, green at bottom of curve)
Group Half-Life
(sec)
Delayed Neutron Fraction
Average Energy (MeV)
1 55.7 0.00021 0.252 22.7 0.00142 0.463 6.2 0.00127 0.414 2.3 0.0026 0.455 0.61 0.00075 0.416 0.23 0.00027 -
Total - 0.0065 -
Delayed Neutron Precursor Groups for Thermal Fission in 235-U
several sources of delayed n’s typical ≈O(1 sec) Fraction d ≈ 0.6%
Energ
y
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
19
6.2 Fission Reactors (Reactor control)
Since fuel rods “hopefully” remain in reactor longer then 10-2 s must include delayed n fraction d
New control problem: keep (+d)q = 1 to accuracy of < 6% at time scale of few seconds
Doable with mechanical system but not easy
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
20
6.2 Fission Reactors (Reactor cooling)
As q rises, power produced in reactor rises cool reactor and drive “heat engine” with coolant coolant will also act as moderator
Coolant/Moderator choices:
Material
State n-abs reduce En
chemistry
other coolant
H2O liquid
small
best reactive cheap good
D2O liquid
none
2nd best reactive rare good
C solid mild medium reactive cheap medium
CO2press. gas mild medium passive cheap ok
He gas mild 3rd best very passi.
leaks ok
Na liquid
small
medium very react.
difficult excellent
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
21
6.2 Fission Reactors (Thermal Stability)
Want dq/dT < 0 Many mechanical influences via thermal
expansion Change in n-energy spectrum Doppler broadening of 238U(n,) resonances
large negative contribution to dq/dT Doppler broadening of 239Pu(n,f) in fast
reactors gives positive contribution to dq/dt Chernobyl No 4. had dq/dT >1 at low power
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
22
6.2 Fission Reactors (Thermal vs. Fast)
Fast reactors need very high 239Pu concentration Bombs very compact core hard to cool need high
Cp coolant like liq.Na or liq. NaK-mix don’t like water & air & must keep coolant circuit molten & high activation of Na
High coolant temperature (550C) good thermal efficiency
Low pressure in vessel better safety can utilise all 238U via breeding 141 time more
fuel High fuel concentration + breading Can
operate for long time without rod changes Designs for 4th generation Pb or gas cooled fast
reactors exist. Could overcome the Na problems
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
23
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
24
25
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
26
6.2 Fission Reactors (Thermal vs. Fast)
Thermal Reactors Many different types exist
BWR = Boiling Water Reactor PWR = Pressure Water Reactor BWP/PWR exist as
LWR = Light Water Reactors (H2O) HWR = Heavy Water Reactors (D2O)
(HT)GCR = (High Temperature) Gas Cooled Reactor exist as
PBR = Pebble Bed Reactor other more conventional geometries
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
27
6.2 Fission Reactors (Thermal vs. Fast)
Thermal Reactors (general features) If moderated with D2O (low n-capture)
can burn natural U now need for enrichment (saves lots of energy!)
Larger reactor cores needed more activation
If natural U used small burn-up time often need continuous fuel exchange hard to control
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
28
6.2 Fission Reactors (Light vs. Heavy water thermal reactors)
Light Water it is cheap very well understood chemistry compatible with steam part of plant can not use natural uranium (too much n-
capture) must have enrichment plant bombs
need larger moderator volume larger core with more activation
enriched U has bigger n-margin easier to control
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
29
6.2 Fission Reactors (Light vs. Heavy water thermal reactors)
Heavy Water it is expensive allows use of natural U natural U has smaller n-margin harder to
control smaller moderator volume less
activation CANDU PWR designs (pressure tube reactors)
allow D2O moderation with different coolants to save D2O
30
6.2 Fission Reactors (PWR = most common power reactor)
Avoid boiling better control of moderation Higher coolant temperature higher thermal efficiency If pressure fails (140 bar) risk of cooling failure via boiling Steam raised in secondary
circuit no activity in turbine and generator
Usually used with H2O need enriched U
Difficult fuel access long fuel cycle (1yr) need highly enriched U
Large fuel reactivity variation over life cycle need variale “n-poison” dose in coolant
31
6.2 Fission Reactors (BWR = second most common power reactor)
lower pressure then PWR (70 bar) safer pressure vessel simpler design of vessel and heat steam circuit primary water enters turbine activation of tubine no
access during operation (½(16N)=7s, main contaminant) lower temperature lower efficiency
if steam fraction too large (norm. 18%) Boiling crisis =loss of cooling
32
6.2 Fission Reactors (“cool” reactors)
33
6.2 Fission Reactors (“cool” reactors)
• no boiling crisis• no steam handling• high efficiency 44%• compact core• low coolant mass
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
34
6.2 Fission Reactors (enrichment)
Two main techniques to separate 235U from 238U in gas form UF6 @ T>56C, P=1bar centrifugal separation
high separation power per centrifugal step low volume capacity per centrifuge total 10-20 stages to get to O(4%) enrichment energy requirement: 5GWh to supply a 1GW reactor with 1
year of fuel diffusive separation
low separation power per diffusion step high volume capacity per diffusion element total 1400 stages to get O(4%) enrichment energy requirement: 240GWh = 10 GWdays to supply a
1GW reactor with 1 year of fuel
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
35
15-20 cm
1-2
m
O(70,000) rpm Vmax≈1,800 km/h = supersonic! & gmax=106g difficult to build!
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
36
6.2 Fission Reactors (enrichment)
37
6.3 Fission Bombs (fission fuel properties)
ideal bomb fuel = pure 239Pu
Isotope Half-lifea Bare critical mass
Spontaneousfission neutrons
Decay heat
yearskg, Alpha-phase
(gm-sec)-1 watts kg-1
Pu-238 87.7 10 2.6x103 560
Pu-239 24,100 10 22x10-3 1.9
Pu-240 6,560 40 0.91x103 6.8
Pu-241 14.4 10 49x10-3 4.2
Pu-242 376,000 100 1.7x103 0.1
Am-241 430 100 1.2 114
a. By Alpha-decay, except Pu-241, which is by Beta-decay to Am-241.
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
38
6.3 Fission Bombs (where to get Pu from?)
Grade Isotope
Pu-238 Pu-239 Pu-240 Pu-241a Pu-242
Super-grade - .98 .02 - -
Weapons-gradeb .00012 .938 .058 .0035 .00022
Reactor-gradec .013 .603 .243 .091 .050
MOX-graded .019 .404 .321 .178 .078
FBR blankete - .96 .04 - -
c. Plutonium recovered from low-enriched uranium pressurized-water reactor fuel that has released 33 megawatt-days/kg fission energy and has been stored for ten years prior to reprocessing (Plutonium Fuel: An Assessment (Paris:OECD/NEA, 1989) Table 12A).
a. Pu-241 plus Am-241.
d. Plutonium recovered from 3.64% fissile plutonium MOX fuel produced from reactor-grade plutonium and which has released 33 MWd/kg fission energy and has been stored for ten years prior to reprocessing (Plutonium Fuel: An Assessment(Paris:OECD/NEA, 1989) Table 12A).
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
39
6.3 Fission Bombs (drawbacks of various Pu isotopes)
241Pu: decays to 241Am which gives very high energy -rays shielding problem
240Pu: lots of spontaneous fission n 238Pu: decays quickly lots of heat conventional
ignition explosives don’t like that! in pure 239Pu bomb, ignition timed optimally during
compression using burst of n maximum explosion yield
… but using reactor grade Pu, n from 240Pu can ignite bomb prematurely lower explosion yield but still a very bad bomb
Reactor grade Pu mix has drawbacks but can “readily” be made into a bomb.
19 Nov 2004, Lecture 6 Nuclear Physics Lectures, Dr. Armin Reichold
40
Plutonium isotope composition as a function of fuel exposure in a pressurized-water reactor, upon discharge.
6.3 Fission Bombs (suspicious behaviour)
Early removal of fission fuel rods need control of reactor fuel changing cycle!
Building fast breaders if you have no fuel recycling plants
Large high-E sources from 241Am outside a reactor
large n fluxes from 240Pu outside reactors very penetrating easy to spot over long range