19 Hydraulic Controls Bulldozers Rippers and Winches · 2018-03-21 · Track-Type Tractors Features...

19

Edition 47 19-1

TRACK-TYPE TRACTORSHydraulic Controls

Bulldozers

Rippers and Winches

CONTENTS

TRACK-TYPE TRACTORS

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-1Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-3Power Shift Drawbar Pull vs. Ground Speed Curves. . . . . . . . . . . . . . . . . .19-18Power Shift Travel Speeds . . . . . . . . . . . . . . . . . . .19-24Ground Pressures . . . . . . . . . . . . . . . . . . . . . . . . .19-26Extreme Slope Operation . . . . . . . . . . . . . . . . . . .19-28

HYDRAULIC CONTROLS

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-29Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-30

BULLDOZERS

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-33Summary of Blade Options. . . . . . . . . . . . . . . . . .19-34Blade Selection . . . . . . . . . . . . . . . . . . . . . . . . . . .19-36General Dimensions (Tractor and Blade) . . . . . . .19-39SAE Blade Capacity Definition . . . . . . . . . . . . . .19-39Blade Specifications. . . . . . . . . . . . . . . . . . . . . . . .19-40Estimating Production Off-the-Job. . . . . . . . . . . .19-50Job Condition Correction Factors . . . . . . . . . . . .19-55Measuring Production On-the-Job . . . . . . . . . . . .19-56Attachments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-56Special Attachments . . . . . . . . . . . . . . . . . . . . . . .19-57

RIPPERS

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-59Ripper Specification Diagrams Adjustable Parallelogram Ripper . . . . . . . . . . .19-60 Radial Ripper . . . . . . . . . . . . . . . . . . . . . . . . . .19-62 Fixed Parallelogram Ripper . . . . . . . . . . . . . . .19-62Specifications Track-Type Tractors . . . . . . . . . . . . . . . . . . . . .19-63Tip Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-73Estimating Ripping Production . . . . . . . . . . . . . .19-73Seismic Wave Velocity Charts . . . . . . . . . . . . . . . .19-76Estimated Ripper Production Graphs . . . . . . . . .19-81

WINCHES

PACCAR

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-84 Physical Specifications. . . . . . . . . . . . . . . . . . . .19-85 Operating Specifications . . . . . . . . . . . . . . . . . .19-95

Allied

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-99 Physical Specifications. . . . . . . . . . . . . . . . . . 19-100 Operating Specifications . . . . . . . . . . . . . . . . .19-107

TRACK-TYPE TRACTORS

Features:

● Cat® Diesel Engines provide the power, high torque rise, reliability and performance you can depend on.

● HEUI™ on D6R and D7R increases fuel efficiency, reduces smoke, improves cold starting and enhances diagnostic capabilities.

● Mechanical Electronic Unit Injector (MEUI™) on D8T, D9T, D10T2 and D11T excels in its ability to control injec tion pressure over the entire engine operating speed range. It combines the technical advancement of an electronic control system with the simplicity of direct mechanically controlled unit fuel injection. These features allow the engine to have complete con trol over injection timing, duration, and pressure.

● Common Rail fuel injection system on D3K2, D4K2, D5K2, D6K2, D5R2, D6N, D6T and D7E machines; opti mizes performance and fuel con sump tion, mini-mizes heat rejection, and lowers emissions.

FeaturesTrack-Type Tractors

19-2 Edition 47

● Oil cooled steering clutches and brakes stan dard on D9R, D10T2 and D11T.

● Finger Tip Controls (FTC) of transmission, steering clutches and brakes on D10T2 and D11T.

● Differential steering allows infinitely variable turn ing radius. Standard on the D5R2, D6N, D6R2, D6T, D7R, D7E, D8R, D8T and D9T, allows the tractor to make a “power turn” keeping both tracks working for more traction and higher performance.

● Electronic Hydrostatic Power Train System on D3K2 through D6K2 allows power turns, stepless speed range, smooth modulation, dynamic hydrostatic braking, supe-rior maneuverability and excel lent controllability.

● Electric Drive Power Train System on D7E allows step-less speed range, smooth modulation, and excellent efficiency. When coupled with differ ential steer it pro-vides superior maneuverability with locked-track pivot turn capability and excellent controllability.

● Combined hand lever steering located left of operator provides easier operation on D9R.

● Standard Tractors designed for heavy dozing and gen-eral grading.

● XL Tractor D6T offers higher horsepower and longer roller frames for increased finish grading capability, flotation and productivity.

● Extra Wide (XW) gauge on D6T length roller frame provides wider shoes for greater flotation and sta bil-ity for steep slope grading.

● Sealed and Lubricated Track reduces pin and bush-ing wear for lower undercarriage repair costs. Sealed and lubricated track is standard on the D3K2, D4K2, and D5K2 while heavy duty track chain is available on D5R, D6K2, D6N, D6T, and D7E improves wear life and reduces pin/bore stretching and cracking.

● SystemOne™ Undercarriage extends undercarriage sys tem life, improves reliability, and reduces owning and operating costs. Optional on D6T (all sources), D5R2, D6K2, D6N, D6R2, optional on D8T and D8R (all sources), D3K2, D4K2, D5K2.

● Elevated sprockets (not on D6K2 or D7E) eliminate final drive stress induced by roller frame movement and ground impact loads. Final drives pull chain only. Seals moved up out of dirt, sand and water for longer life. Blade visibility improved because operator sits higher.

● Resilient mounted bogie undercarriage on D8R, D8T, D9T, D10T2 and D11T reduces shock transmitted to tractor. Allows track to conform to rough ground for better traction.

● Solid mounted undercarriage standard on D3K2 through D5K2 provides stable platform for low impact, and high abrasion applications. Provides optimum finish grad-ing performance.

● Oscillating undercarriage on D6K2 through D7E and optional on the D8R and D8T decreases ground shock to the machine and provides a smoother, more com fort able ride for the operator.

● Accessible modular design on D6N XL and up greatly reduces drive train removal and installation time result-ing in reduced repair costs.

● Tag link on D7R, D8R/D8T and up; L-shaped push arms on D6N, D6T and D7E. Both designs allow closer mounting of dozer blades. This reduces total tractor length, improves maneuverability, balance, blade pen etration and pryout.

● Low ground pressure (LGP) tractors offer greater flo-tation in soft, swampy conditions. Available on D3K2 through D8T.

19

Specifications Track-Type Tractors

Edition 47 19-3

MODEL D3K2 XL D3K2 LGP D3K2 XL D3K2 LGP

Emission Standards U.S. EPA Tier 3/EU Stage IIIA/

Japan 2006 (Tier 3) equivalent1

Tier 3/Stage IIIA/Japan 2006 (Tier 3)

equivalent1

Tier 4 Final/Stage IV/Japan 2014

(Tier 4 Final)


(Tier 4 Final)

Flywheel Power 55.2 kW 74 hp 55.2 kW 74 hp 59.7 kW 80 hp 59.7 kW 80 hp

Operating Weight2 7795 kg 17,185 lb 8093 kg 17,842 lb 7958 kg 17,544 lb 8403 kg 18,525 lb

Engine Model C4.4 ACERT™ C4.4 ACERT C4.4 ACERT C4.4 ACERT

Rated Engine RPM 1900 1900 2200 2200

No. of Cylinders 4 4 4 4

Bore 105 mm 4.13" 105 mm 4.13" 105 mm 4.13" 105 mm 4.13"

Stroke 127 mm 5.0" 127 mm 5.0" 127 mm 5.0" 127 mm 5.0"

Displacement 4.4 L 269 in3 4.4 L 269 in3 4.4 L 269 in3 4.4 L 269 in3

Track Rollers (Each Side) 6 6 6 6

Width of Standard Track Shoe 406 mm 16" 635 mm 25" 406 mm 16" 635 mm 25"

Length of Track on Ground 2095 mm 83" 2095 mm 83" 2248 mm 89" 2248 mm 89"

Ground Contact Area

(w/Std. Shoe) 17 011 cm2 2637 in2 26 607 cm2 4124 in2 18 254 cm2 2848 in2 28 550 cm2 4425 in2

Track Gauge 1495 mm 59" 1725 mm 68" 1495 mm 59" 1725 mm 68"

GENERAL DIMENSIONS:

Height (To Top of ROPS) 2763 mm 108.8" 2763 mm 108.8" 2763 mm 108.8" 2763 mm 108.8"

Overall Length (with P blade) 4266 mm 168" 4255 mm 167.6" 4266 mm 168" 4266 mm 168"

(without Blade) 3275 mm 128.9" 3275 mm 128.9" 3275 mm 128.9" 3275 mm 128.9"

Width (w/o Trunnion and Blade

— Std. Shoe) 1901 mm 74.8" 2360 mm 92.9" 1901 mm 74.8" 2360 mm 92.9"

Ground Clearance 332 mm 13" 332 mm 13" 332 mm 13" 332 mm 13"

Blade Types and Widths:

VPAT, Straight 2646 mm 104.1" 3149 mm 124.0" 2646 mm 104.1" 3149 mm 124"

VPAT, Angled 25° 2417 mm 95.1" 2874 mm 113" 2417 mm 95.1" 2874 mm 113"

Fuel Tank Refill Capacity 195 L 51.5

U.S. gal

195 L 51.5

U.S. gal

195 L 51.5

U.S. gal

195 L 51.5 U.S. gal

DEF Tank Refill Capacity — — 19 L 5 U.S. gal 19 L 5 U.S. gal1 Meets Tier 3/Stage IIIA/Japan 2006 (Tier 3) equivalent emission standards.2 Operating weight includes ROPS canopy, operator, lubricants, coolant, full fuel tank, hydraulic controls and fluids, back-up alarm, seat belts, lights, rigid

drawbar, front pull device and standard service crankcase guard.

19-4 Edition 47

Track-Type Tractors Specifications


Emission Standards Tier 3/Stage IIIA/Japan 2006 (Tier 3)

equivalent1


equivalent1


(Tier 4 Final)


(Tier 4 Final)

Flywheel Power 62.6 kW 84 hp 62.6 kW 84 hp 68.8 kW 92 hp 68.8 kW 92 hp

Operating Weight2 8147 kg 17,961 lb 8501 kg 18,742 lb 8201 kg 18,080 lb 8510 kg 18,761 lb

Engine Model C4.4 ACERT C4.4 ACERT C4.4 ACERT C4.4 ACERT

Rated Engine RPM 1900 1900 2200 2200


Bore 105 mm 4.13" 105 mm 4.13" 105 mm 4.13" 105 mm 4.13"

Stroke 127 mm 5.0" 127 mm 5.0" 127 mm 5.0" 127 mm 5.0"




Length of Track on Ground 2248 mm 89" 2248 mm 89" 2248 mm 89" 2248 89"

Ground Contact Area



GENERAL DIMENSIONS:

Height (To Top of ROPS) 2763 mm 108.8" 2763 mm 108.8" 2763 mm 108.8" 2763 mm 108.8"

Overall Length (with P blade) 4274 mm 168" 4266 mm 168" 4266 mm 168" 4266 mm 168"






VPAT, Straight 2782 mm 109.5" 3149 mm 124.0" 2782 mm 109.5" 3149 mm 124"

VPAT, Angled 25° 2542 mm 100.1" 2874 mm 113" 2542 mm 100.1" 2874 mm 113"


U.S. gal

195 L 51.5

U.S. gal

195 L 51.5

U.S. gal

195 L 51.5 U.S. gal

DEF Tank Refill Capacity — — 19 L 5 U.S. gal 19 L 5 U.S. gal1 Meets Tier 3/Stage IIIA/Japan 2006 (Tier 3) equivalent emission standards.2 Operating weight includes ROPS canopy, operator, lubricants, coolant, full fuel tank, hydraulic controls and fluids, back-up alarm, seat belts, lights, rigid

drawbar, front pull device and standard service crankcase guard.

19

Edition 47 19-5




equivalent1


equivalent1


(Tier 4 Final)


(Tier 4 Final)

Flywheel Power:

Hydrostatic 71.6 kW 96 hp 71.6 kW 96 hp 77.6 kW 104 hp 77.6 kW 104 hp

Operating Weight:2

Hydrostatic 9408 kg 20,741 lb 9683 kg 21,347 lb 9314 kg 20,534 lb 9646 kg 21,266 lb


Rated Engine RPM 1900 1900 2100 2100


Bore 105 mm 4.13" 105 mm 4.13" 105 mm 4.13" 105 mm 4.13"

Stroke 127 mm 5.0" 127 mm 5.0" 127 mm 5.0" 127 mm 5.0"





Ground Contact Area



GENERAL DIMENSIONS:

Height (To Top of ROPS Canopy) 2769 mm 109.0" 2769 mm 109.0" 2769 mm 109.0" 2769 mm 109.0"

Height (To Top of ROPS Cab) 2769 mm 109.0" 2769 mm 109.0" 2769 mm 109.0" 2769 mm 109.0"

Overall Length (with P Blade) 4321 mm 170.1" 4294 mm 169.1" 4321 mm 170.1" 4321 mm 170.1"






VPAT, Straight 2782 mm 109.5" 3220 mm 126.7" 2782 mm 109.5" 3220 mm 126.7"

VPAT, Angled 25° 2636 mm 103.8" 2940 mm 115.8" 2636 mm 103.8" 2940 mm 115.8"


U.S. gal

195 L 51.5

U.S. gal

195 L 51.5

U.S. gal

195 L 51.5

U.S. gal

DEF Tank Refill Capacity — — 19 L 5 U.S. gal 19 L 5 U.S. gal1 Meets Tier 3/Stage IIIA/Japan 2006 (Tier 3) equivalent emission standards.2 Operating weight includes ROPS canopy, operator, lubricants, coolant, full fuel tank, hydraulic controls and fluids, back-up alarm, seat belts, lights, rigid drawbar, front pull device and standard service crankcase guard.

MODEL D5R2 XL D5R2 LGP D5T XL

Emission Standards Tier 3/Stage IIIA/

Japan 2006 (Tier 3)

equivalent

Tier 3/Stage IIIA/

Japan 2006 (Tier 3)

equivalent

Tier 3/Stage IIIA/

Japan 2006 (Tier 3)

equivalent

Flywheel Power 112 kW 150 hp 112 kW 150 hp 112 kW 150 hp

Operating Weight:

Power Shift Differential Steer 16 672 kg 36,755 lb 18 584 kg 40,971 lb 16 672 kg 36,755 lb

Engine Model C7.1 ACERT C7.1 ACERT C7.1 ACERT

Rated Engine RPM 2200 2200 2200

No. of Cylinders 6 6 6

Bore 105 mm 4.13" 105 mm 4.13" 105 mm 4.13"

Stroke 135 mm 5.3" 135 mm 5.3" 135 mm 5.3"

Displacement 7.01 L 427.8 in3 7.01 L 427.8 in3 7.01 L 427.8 in3

Track Rollers (Each Side) 7 8 7

Width of Standard Track Shoe 610 mm 24" 840 mm 33.1" 610 mm 24"

Length of Track on Ground 2611 mm 103" 3113 mm 122.6" 2611 mm 103"

Ground Contact Area (w/Std. Shoe) 3.18 m2 4929 in2 5.23 m2 8107 in2 3.18 m2 4929 in2

Track Gauge 1890 mm 74.4" 2160 mm 85" 1890 mm 74.4"

GENERAL DIMENSIONS:

Height (To Top of ROPS Cab/Canopy) 3086 mm 121.5" 3200 mm 126.0" 3086 mm 121.5"

Length of Basic Tractor (w/o Blade) 3480 mm 137.0" 4017 mm 158.1" 3480 mm 137.0"

with following attachments, add:

SU Blade 1546 mm 60.9" — 1546 mm 60.9"

A Blade (when Straight) 1450 mm 57.1" — —

A Blade (when Angled 25°) 2303 mm 90.7" — —

VPAT Blade (when Straight) 1343 mm 52.9" 1249 mm 49.2" 1343 mm 52.9"

VPAT Blade (when Angled 25°) 1965 mm 77.4" 2004 mm 78.9" 1965 mm 77.4"

Rear Drawbar 192 mm 7.6" 148 mm 5.8" 192 mm 7.6"

Multi-Shank Ripper

(tip at ground level) 1230 mm 48.4" 1190 mm 46.9" 1230 mm 48.4"

Width of Tractor: 2500 mm 98.4" 3000 mm 118" 2500 mm 98.4"

Over Trunnion 2640 mm 103.9" 3279 mm 129.1" 2640 mm 103.9"

Without Trunnion

(standard shoe width) 2490 mm 98.0" 3000 mm 118.1" 2490 mm 98.0"

Ground Clearance 394 mm 15.5" 507 mm 20.0" 394 mm 15.5"


SU Blade 3154 mm 124.2" — 3154 mm 124.2"

A Blade 4165 mm 164.0" — —

VPAT Blade — XL 3272 mm 128.8" — 3272 mm 128.8"

VPAT Blade — LGP — 4080 mm 160.6" —

Fuel Tank Refill Capacity 299 L 79.3 U.S. gal 299 L 79.3 U.S. gal 299 L 79.3 U.S. gal

SpecificationsTrack-Type Tractors

19-6 Edition 47

Edition 47 19-7

Track-Type Tractors Specifications19



equivalent


equivalent


(Tier 4 Final)


(Tier 4 Final)

Flywheel Power:

Hydrostatic 97 kW 130 hp 97 kW 130 hp 97 kW 130 hp 97 kW 130 hp

Operating Weight:

Hydrostatic 13 311 kg 29,346 lb 13 948 kg 30,750 lb 13 271 kg 29,258 lb 13 909 kg 30,664 lb


Rated Engine RPM 2200 2200 2200 2200


Bore 105 mm 4.13" 105 mm 4.13" 105 mm 4.13" 105 mm 4.13"

Stroke 135 mm 5.31" 135 mm 5.31" 127 mm 5.0" 127 mm 5.0"

Displacement 7.01 L 428.8 in3 7.01 L 428.8 in3 4.4 L 269 in3 4.4 L 269 in3

Track Rollers (Each Side) 7 or 8 7 or 8 8 8



Ground Contact Area

(w/Std. Shoe) 3.0 m2 4650 in2 4.0 m2 6200 in2 3.0 m2 4650 in2 4.0 m2 6200 in2


GENERAL DIMENSIONS:

Height (To Top of ROPS Cab) 2958 mm 116.5" 2958 mm 116.5" 2958 mm 116.5" 2958 mm 116.5"

Overall Length

(with VPAT Blade)** 5008 mm 197" 5008 mm 197" 5008 mm 197" 5008 mm 197"

without Blade** 4588 mm 181" 4588 mm 181" 4588 mm 181" 4588 mm 181"


— Std. Shoe)* 2330 mm 91.7" 2760 mm 108.7" 2330 mm 91.7" 2760 mm 108.7"

Ground Clearance 360 mm 14.2" 360 mm 14.2" 360 mm 14.2" 360 mm 14.2"


VPAT, straight 3196 mm 125.8" 3682 mm 145.0" 3196 mm 125.8" 3682 mm 145.0"

VPAT, angled 2896 mm 114.0" 3337 mm 131.4" 2896 mm 114.0" 3337 mm 131.4"

Fuel Tank Refill Capacity 295 L 77.9 U.S. gal

295 L 77.9 U.S. gal

260 L 69U.S. gal

260 L 69U.S. gal

DEF Tank Refill Capacity — — 19 L 5 U.S. gal 19 L 5 U.S. gal

*Width (w/o Trunnion — Std. Shoe) is also w/o VPAT Blade.**With drawbar.

19-8 Edition 47


MODEL D6N XL D6N LGP

Emission Standards Tier 4 Final/Stage IV/Japan 2014 (Tier 4 Final)

Tier 4 Final/Stage IV/Japan 2014 (Tier 4 Final)

Flywheel Power:

Power Shift 124 kW 166 hp 124 kW 166 hp

Operating Weight:

Power Shift Differential Steer 16 757 kg 36,943 lb 18 346 kg 40,446 lb

Engine Model C7.1 ACERT C7.1 ACERT

Rated Engine RPM 2200 2200

No. of Cylinders 6 6

Bore 105 mm 4.13" 105 mm 4.13"

Stroke 135 mm 5.3" 135 mm 5.3"

Displacement 7.1 L 433 in3 7.1 L 433 in3

Track Rollers (Each Side) 7 8

Width of Standard Track Shoe 610 mm 24" 840 mm 33"

Length of Track on Ground 2605 mm 102.6" 3110 mm 122.4"

Ground Contact Area (w/Std. Shoe) 3.18 m2 4929 in2 5.24 m2 8122 in2

Track Gauge 1890 mm 74.4" 2160 mm 85"

GENERAL DIMENSIONS:

Height (To Top of ROPS Canopy) NA** NA**

Height (To Top of ROPS Cab) 3088 mm 121.6" 3202 mm 126"

Overall Length (with VPAT Blade) 5035 mm 198.2" 5401 mm 212.6"

without Blade 3735 mm 147" 4146 mm 163.2"

with SU Blade 5165 mm 203.3" —

Width (over Trunnion) 2630 mm 103.5" —

Width (w/o Trunnion — Std. Shoe)* 2500 mm 98.4" 3000 mm 118"

Ground Clearance 394 mm 15.5" 507 mm 20"


Semi-U 3154 mm 124.2" —

VPAT 3272 mm 128.8" 4080 mm 160.6"

Fuel Tank Refill Capacity 277 L 73.2 U.S. gal 277 L 73.2 U.S. gal

Diesel Exhaust Fluid Refill Capacity 19 L 5 U.S. gal 19 L 5 U.S. gal

*Width (w/o Trunnion — Std. Shoe) is also w/o VPAT Blade.**Canopy not available.

19

MODEL D6R2 D6R2 XL D6R2 LGP

Emission Standards Tier 3/Stage IIIA/

Japan 2006 (Tier 3)

equivalent1

Tier 3/Stage IIIA/

Japan 2006 (Tier 3)

equivalent1

Tier 3/Stage IIIA/

Japan 2006 (Tier 3)

equivalent1

Flywheel Power:

Stage II — ISO 9249/SAE J1349 133 kW 179 hp 148 kW 198 hp 148 kW 198 hp

Stage IIIA — ISO 9249/SAE J1349 147 kW 196 hp 153 kW 206 hp 153 kW 206 hp

Operating Weight:2

Power Shift Differential Steer (SU Blade) 19 066 kg 42,033 lb 19 914 kg 43,903 lb 21 661 kg 47,754 lb

Engine Model C9 ACERT C9 ACERT C9 ACERT

Rated Engine RPM:

Stage II 2000 2000 2000

Stage IIIA 1850 1850 1850


Bore 112 mm 4.4" 112 mm 4.4" 112 mm 4.4"

Stroke 149 mm 5.9" 149 mm 5.9" 149 mm 5.9"

Displacement 8.8 L 537 in3 8.8 L 537 in3 8.8 L 537 in3


Width of Standard Track Shoe 560 mm 22" 560 mm 22" 915 mm 36"

Length of Track on Ground 2664 mm 104.9" 2871 mm 113" 3275 mm 128.9"


Track Gauge 1880 mm 74" 1880 mm 74" 2286 mm 90.0"

GENERAL DIMENSIONS:

Height (To Top of ROPS Cab/Canopy) 3216 mm 126.6" 3216 mm 126.6" 3266 mm 128.6"

Height (To Exhaust Stack) 3115 mm 122.6" 3115 mm 122.6" 3165 mm 124.6"

Length of Basic Tractor (w/o Blade) 3860 mm 152.0" 3860 mm 152.0" 4247 mm 167.2"


S Blade 1043 mm 41.1" — 1218 mm 48.0"

SU Blade 1235 mm 48.6" 1472 mm 58.0" —

Angle Blade (when Straight) 1147 mm 45.2" 1349 mm 53.1" —

Angle Blade (when Angled 25°) 1983 mm 78.1" 2185 mm 86.0" —


Muiti-Shank Ripper

(tip at ground level) 1403 mm 55.2" 1403 mm 55.2" —

Width of Tractor:

Over Trunnion 2640 mm 103.9" 2640 mm 103.9" 3491 mm 137.4"

Without Trunnion

(standard shoe width) 2440 mm 96.1" 2440 mm 96.1" 3201 mm 126.0"

Ground Clearance 372 mm 14.6" 372 mm 14.6" 422 mm 16.6"


S Blade 3360 mm 132.3" — 4063 mm 160.0"

SU Blade 3260 mm 128.3" 3260 mm 128.3" —

Angle Blade 4166 mm 164.0" 4166 mm 164.0" —

Fuel Tank Refill Capacity 424 L 112 U.S. gal 424 L 112 U.S. gal 424 L 112 U.S. gal1 Meets Tier 2/Stage II/Japan 2001 (Tier 2) equivalent OR Tier 3/Stage IIIA/Japan 2006 (Tier 3) equivalent emission standards.2 Operating weight includes ROPS canopy, operator lubricants, coolants, full fuel tank, hydraulic controls and fluid, SU blades, horn, backup alarm, retrival hitch and front pull hook.

Edition 47 19-9



MODEL D6T D6T XLEmission Standards Tier 3/Stage IIIA/

Japan 2006 (Tier 3) equivalentTier 3/Stage IIIA/

Japan 2006 (Tier 3) equivalent

Flywheel Power 149 kW 200 hp 149 kW 200 hp

Operating Weight:1

Power Shift Differential Steer

SU Blade 20 580 kg 45,370 lb 21 600 kg 47,620 lb

Engine Model C9 ACERT C9 ACERT

Rated Engine RPM: Power Shift 1850 1850


Bore 112 mm 4.4" 112 mm 4.4"

Stroke 149 mm 5.9" 149 mm 5.9"




Length of Track on Ground 2.61 m 8'7" 2.81 m 9'3"


Track Gauge 1.88 m 74" 1.88 m 74"

GENERAL DIMENSIONS:

Height2 (Stripped Top)3 2.40 m 7'11" 2.40 m 7'11"

Height2 (To Top of ROPS Canopy) 3.11 m 10'2" 3.11 m 10'2"

Height2 (To Top of ROPS Cab) 3.11 m 10'2" 3.11 m 10'2"

Overall Length (without Blade) 3.85 m 12'7" 3.85 m 12'7"

with SU Blade 5.08 m 16'8" 5.33 m 17'6"

with Angle Blade 5.00 m 16'5" 5.21 m 17'1"

Width (over Trunnion) 2.64 m 8'8" 2.64 m 8'8"

Width (w/o Trunnion — Std. Track) 2.44 m 8'0" 2.44 m 8'0"

Ground Clearance2 384 mm 1'3" 384 mm 1'3"


Angle Straight 4.16 m 13'8" 4.16 m 13'8"

Full 25° Angle 3.77 m 12'5" 3.77 m 12'5"

Semi-U 3.26 m 10'8" 3.26 m 10'8"

Fuel Tank Refill Capacity 425 L 112 U.S. gal 425 L 112 U.S. gal1 Operating weight includes cab, operator, lubricants, coolant, full fuel tank, standard track, hydraulic controls and fluid, SU blade, drawbar and counterweight.2 Dimensions measured from ground line. Add grouser height for total dimension on hard surfaces.3 Height (Stripped Top) — without ROPS canopy, exhaust, seat back or other easily removed encumbrances.

Track-Type Tractor Sustainability

Well matched engine and power train systems enhance productivity and fuel efficiency.

19-10 Edition 47

19


Edition 47 19-11

MODEL D6T XL D6T XW D6T LGPEmission Standards Tier 4 Final/Stage IV/

Japan 2014 (Tier 4 Final)Tier 4 Final/Stage IV/

Japan 2014 (Tier 4 Final)Tier 4 Final/Stage IV/

Japan 2014 (Tier 4 Final)


Operating Weight:1


VPAT 23 663 kg 52,167 lb 24 118 kg 53,170 lb 24 336 kg 53,651 lb

Engine Model C9.3 ACERT C9.3 ACERT C9.3 ACERT

Advertised Engine RPM 2000 2000 2000


Bore 115 mm 4.5" 115 mm 4.5" 115 mm 4.5"

Stroke 149 mm 5.9" 149 mm 5.9" 149 mm 5.9"



VPAT 7 8 8


VPAT 560 mm 22" 710 mm 28" 785 mm 31"

Length of Track on Ground 2.84 m 9'5" 2.84 m 9'5" 3.25 m 10'9"

VPAT 2.84 m 9'5" 3.25 m 10'9" 3.25 m 10'9"

Ground Contact Area (w/Std. Shoe) 3.54 m2 5489 in2 4.81 m2 7449 in2 6.53 m2 10,122 in2

VPAT 3.54 m2 5489 in2 5.10 m2 7909 in2 5.60 m2 8684 in2

Track Gauge 1.88 m 74" 2.03 m 80" 2.29 m 90"

VPAT 2.13 m 84" 2.29 m 90" 2.29 m 90"

GENERAL DIMENSIONS:

Height2 (Stripped Top3) 2.46 m 8'1" 2.46 m 8'1" 2.51 m 8'3"

VPAT 2.46 m 8'1" 2.51 m 8'3" 2.51 m 8'3"

Height2 (To Top of ROPS Canopy) 3.11 m 10'2" 3.11 m 10'2" 3.16 m 10'4"

VPAT 3.11 m 10'2" 3.16 m 10'4" 3.16 m 10'4"

Height2 (To Top of ROPS Cab) 3.15 m 10'4" 3.15 m 10'4" 3.20 m 10'6"

VPAT 3.15 m 10'4" 3.20 m 10'6" 3.20 m 10'6"

Overall Length (without Blade) 3.89 m 12'9" 3.89 m 12'9" 4.25 m 13'11"

VPAT 3.89 m 12'9" 4.25 m 13'11" 4.25 m 13'11"

with S Blade — — 5.50 m 18'1"

with SU Blade 5.33 m 17'6" 5.33 m 17'6" —

with VPAT Blade 5.39 m 17'8" 5.53 m 18'2" 5.53 m 18'2"

with Angle Blade 5.21 m 17'1" 5.29 m 17'4" 5.81 m 19'1"

Width (over Trunnion) 2.69 m 8'10" 2.94 m 9'8" 3.48 m 11'5"

Width (w/o Trunnion — Std. Track) 2.59 m 8'6" 2.79 m 9'2" 3.20 m 10'6"

VPAT 2.72 m 8'11" 3.00 m 9'10" 3.14 m 10'4"

Ground Clearance2 372 mm 1'3" 372 mm 1'3" 406 mm 1'4"

VPAT 372 mm 1'3" 406 mm 1'4" 406 mm 1'4"


Straight — — 4.06 m 13'4"

Angle Straight 4.16 m 13'8" 4.52 m 14'10" 5.07 m 16'8"

Full 25° Angle 3.77 m 12'5" 4.11 m 13'6" 4.63 m 15'2"

Semi-U 3.26 m 12'8" 3.56 m 11'8" —

VPAT

Straight 3.88 m 12'9" 4.16 m 13'8" 4.16 m 13'8"

Full 24° Angle 3.54 m 11'7" 3.79 m 12'5" 3.79 m 12'5"

Fuel Tank Refill Capacity 411 L 109 U.S. gal 411 L 109 U.S. gal 411 L 109 U.S. gal

DEF Tank Refill Capacity 17.1 L 4.5 U.S. gal 17.1 L 4.5 U.S. gal 17.1 L 4.5 U.S. gal1 Operating weight includes cab, operator, lubricants, coolant, full fuel tank, standard track, hydraulic controls and fluid, SU blade and drawbar.2 Dimensions measured from ground line. Add grouser height for total dimension on hard surfaces.3 Height (Stripped Top) — without ROPS canopy, exhaust, seat back or other easily removed encumbrances.


MODEL D7E D7E LGP

Emission Standards Tier 4 Final/Stage IV/Japan 2014 (Tier 4 Final)


Advertised Flywheel Power 178 kW 238 hp 178 kW 238 hp

Operating Weight:1

Electric Drive Differential Steer 26 055 kg 57,441 lb 28 525 kg 62,886 lb

Engine Model C9.3 ACERT C9.3 ACERT

Advertised Engine RPM 1700 1700


Bore 115 mm 4.5" 115 mm 4.5"

Stroke 149 mm 5.9" 149 mm 5.9"






Track Gauge 1.98 m 6'6" 2.29 m 7'6"

GENERAL DIMENSIONS:


Overall Length (without Blade) 4.88 m 16'0" 4.88 m 16'0"

with S Blade 5.86 m 19'3" 5.56 m 18'3"

with SU Blade 6.07 m 19'11" —


Width (w/o Trunnion — Std. Shoe) 2.59 m 8'6" 3.2 m 10'6"

Ground Clearance 472 mm 18.6" 472 mm 18.6"


Straight 3.9 m 12'10" 4.54 m 14'11"

Angle Straight 4.5 m 14'9" —

Full 25° Angle 4.12 m 13'6" —

Universal 3.99 m 13'1" —

Semi-U 3.71 m 12'2" —

Fuel Tank Refill Capacity 430 L 114 U.S. gal 430 L 114 U.S. gal

DEF Tank Refill Capacity 17.5 L 4.6 U.S. gal 17.5 L 4.6 U.S. gal1 Operating weight includes cab, operator, lubricants, coolant, full fuel tank, standard track, hydraulic controls and fluid, SU blade and drawbar.2 Dimensions measured from ground line. Add grouser height for total dimension on hard surfaces.

Cat D7E — Resourceful in every way● The D7E is designed to maximize efficiency and productivity while conserving natural resources.

● Burns 10–30% less fuel per hour than previous models. Less fuel burned means reduced emissions.

● The D7E earned a 2009 Clean Air Excellence Award from the U.S. Environmental Protection Agency.

● More efficient – 25% more material moved per liter/gallon of fuel.

● Fewer parts and longer component life, less fuel and fluids, means less to replace and less to dispose.

● Major structures and components are built to be rebuilt, reducing waste and replacement costs.

19-12 Edition 47

19


Edition 47 19-13

MODEL D7R D7R XR D7R LGP

Emission Standards Tier 2/Stage II/

Japan 2001 (Tier 2)

equivalent1

Tier 2/Stage II/

Japan 2001 (Tier 2)

equivalent1

Tier 2/Stage II/

Japan 2001 (Tier 2)

equivalent1


Operating Weight:2



Rated Engine RPM: Power Shift 2100 2100 2100


Bore 112 mm 4.4" 112 mm 4.4" 112 mm 4.4"

Stroke 149 mm 5.9" 149 mm 5.9" 149 mm 5.9"






Track Gauge 1980 mm 6'6" 1980 mm 6'6" 2235 mm 7'4"

GENERAL DIMENSIONS:

Height3 (Stripped Top)4 2.58 m 8'6" 2.58 m 8'6" 2.7 m 8'10"


Height3 (To Top of ROPS Cab) 3.28 m 10'9" 3.28 m 10'9" 3.36 m 11'0"

Overall Length (without Blade) 4.73 m 15'6" 4.73 m 15'6" 4.73 m 15'6"


with S Blade — — 1071 mm 42.2"

with SU Blade 1301 mm 51.2" 1301 mm 51.2" —

with A Blade (Straight) 1372 mm 54.0" 1372 mm 54.0" —


Muiti-Shank Ripper

(tip at ground level) 2442 mm 96.1" 2442 mm 96.1" 2442 mm 96.1"


Width (w/o Trunnion — Std. Shoe) 2.54 m 8'4" 2.54 m 8'4" 3.15 m 10'4"

Ground Clearance 415 mm 1'4" 415 mm 1'4" 495 mm 1'7"


Straight Blade — — 4545 mm 178.9"

Semi-U Blade 3.69 m 12'2" 3.69 m 12'2" —

Angle Blade 4496 mm 177.0" 4496 mm 177.0" —

Fuel Tank Refill Capacity 481 L 127 U.S. gal 481 L 127 U.S. gal 481 L 127 U.S. gal1 Meets Tier 2/Stage II/Japan 2001 (Tier 2) equivalent OR Tier 3/Stage IIIA/Japan 2006 (Tier 3) equivalent emission standards.2 Operating weight includes cab, operator, lubricants, coolant, full fuel tank, standard track, hydraulic controls and fluid, SU blade, drawbar and counterweight.3 Dimensions measured from ground line. Add grouser height for total dimension on hard surfaces.4 Height (Stripped Top) — without ROPS canopy, exhaust, seat back or other easily removed encumbrances.


Major structures and components are built to be rebuilt, reducing waste and replacement costs.


MODEL D8R D8R LGP

Emission Standards Tier 1/Stage I Tier 1/Stage I

Flywheel Power 226 kW 303 hp 226 kW 303 hp

Operating Weight:1

Power Shift Differential Steer 37 920 kg 83,600 lb 35 176 kg 77,550 lb

Engine Model 3406C TA 3406C TA

Rated Engine RPM 2100 2100


Bore 137 mm 5.4" 137 mm 5.4"

Stroke 165 mm 6.5" 165 mm 6.5"






Track Gauge 2.08 m 6'10" 2.34 m 7'8"

GENERAL DIMENSIONS:

Height2 (Stripped Top)3 2.67 m 8'9" 2.67 m 8'9"

Height2 (To Top of ROPS Canopy) 3.45 m 11'4" 3.51 m 11'6"


Overall Length (with SU Blade)4 6.80 m 22'4" 6.80 m 22'4"

(without Blade) 4.96 m 16'3" 4.96 m 16'3"

Overall Length (without Blade) — —

with S Blade — —


Width (w/o Trunnion — Std. Shoe) 2.70 m 8'8" 3.30 m 10'10"

Ground Clearance 613 mm 2'0" 606 mm 2'0"


Straight — —

Angle Straight 4.99 m 16'4" —

Full 25° Angle 4.52 m 14'10" —

Universal 4.26 m 14'0" —

Semi-U 3.94 m 12'11" 4.40 m 14'5"

Fuel Tank Refill Capacity 625 L 165 U.S. gal 625 L 165 U.S. gal1 Operating weight includes cab, operator, lubricants, coolant, full fuel tank, standard track, hydraulic controls and fluid, SU blade, drawbar and counterweight.— D8R equipped with track guides, ROPS/FOPS cab, single shank ripper and SU blade.

2 Dimensions measured from ground line. Add grouser height for total dimension on hard surfaces.3 Height (Stripped Top) — without ROPS canopy, exhaust, seat back or other easily removed encumbrances.4 Includes drawbar.


Cat tractors are designed for ease of serviceability, with features like ground-level service points and wide engine enclosure doors.

19-14 Edition 47

19


MODEL D8T D8T LGP D8T D8T LGP

Emission Standards Tier 4 Interim/Stage IIIB

Tier 4 Interim/Stage IIIB


(Tier 4 Final)


(Tier 4 Final)

Flywheel Power 233 kW 312 hp 233 kW 312 hp 233 kW 312 hp 233 kW 312 hp

Operating Weight:1

Power Shift Differential Steer 39 751 kg 87,650 lb 37 750 kg 83,224 lb 39 795 kg 87,733 lb 37 795 kg 83,324 lb

Engine Model C15 ACERT C15 ACERT C15 ACERT C15 ACERT

Rated Engine RPM 1900 1900 1900 1900


Bore 137 mm 5.4" 137 mm 5.4" 137 mm 5.4" 137 mm 5.4"

Stroke 172 mm 6.75" 172 mm 6.75" 172 mm 6.75" 172 mm 6.75"




Length of Track on Ground 3.21 m 10'6" 3.20 m 10'6" 3.21 m 10'6" 3.21 m 10'6"

Ground Contact Area

(w/Std. Shoe) 3.91 m2 6062 in2 6.19 m2 9593 in2 3.91 m2 6062 in2 6.19 m2 9593 in2

Track Gauge 2.08 m 6'10" 2.34 m 7'8" 2.08 m 6'10" 2.34 m 7'8"

GENERAL DIMENSIONS:

Height2 (Stripped Top)3 2.67 m 8'9" 2.67 m 8'9" — —

Height2

(To Top of ROPS Canopy) 3.46 m 11'4" 3.45 m 11'4" — —

Height2 (To Top of ROPS Cab) 3.46 m 11'4" 3.46 m 11'4" 3.51 m 11'6" 3.51 m 11'6"

Overall Length (with SU Blade)4 6.09 m 20'0" 6.09 m 20'0" 6.09 m 20'0" 6.09 m 20'0"

(without Blade) 4.64 m 15'3" 4.98 m 16'4" 4.64 m 15'3" 4.98 m 16'4"

Width (over Trunnion) 3.06 m 10'0" 3.38 m 11'1" 3.06 m 10'0" 3.38 m 11'1"

Width (w/o Trunnion —

Std. Shoe) 2.64 m 8'8" 3.30 m 10'10" 2.64 m 8'8" 3.30 m 10'10"

Ground Clearance 613 mm 2'0" 613 mm 2'0" 613 mm 2'0" 613 mm 2'0"


Angle Straight 4.99 m 16'4" — 4.99 m 16'4" —

Full 25° Angle 5.05 m 16'7" — 5.05 m 16'7" —

Universal 4.26 m 14'0" — 4.26 m 14'0" —

Semi-U 3.94 m 12'11" 4.53 m 14'10" 3.94 m 12'11" 4.53 m 14'10"

Fuel Tank Refill Capacity 627 L 165 U.S. gal

627 L 165U.S. gal

627 L 165 U.S. gal

627 L 165 U.S. gal

DEF Tank Refill Capacity — — 24 L 6.3 U.S. gal 24 L 6.3 U.S. gal1 Operating weight includes ROPS/FOPS cab, operator, lubricants, coolant, full fuel tank, standard track, hydraulic controls and fluid, SU blade and ripper. LGP operating weight includes drawbar instead of ripper.

2 Dimensions measured from ground line. Add grouser height for total dimension on hard surfaces.3 Height (Stripped Top) — without ROPS canopy, exhaust, seat back or other easily removed encumbrances.4 Includes drawbar.


Cat engines with ACERT Technology provide powerful reliability, while meeting the stringent emissions standards.

Edition 47 19-15


MODEL D9R D9T D9T

Emission Standards — Tier 3/Stage IIIA/Japan 2006 (Tier 3)

equivalent1



Operating Weight:2

Power Shift Clutch Brake 48 784 kg 107,548 lb — —

Power Shift Differential Steer — 47 872 kg 105,539 lb 48 361 kg 106,618 lb

Engine Model 3408C SCAC C18 ACERT C18 ACERT



Bore 137 mm 5.4" 145 mm 5.7" 145 mm 5.7"

Stroke 152 mm 6" 183 mm 7.2" 183 mm 7.2"

Displacement 18 L 1099 in3 18.1 L 1106 in3 18.1 L 1106 in3





Track Gauge 2.25 m 7'5" 2.25 m 7'5" 2.25 m 7'5"

GENERAL DIMENSIONS:

Height3 (Stripped Top)4 3.69 m 12'1" 3.69 m 12'1" 3.69 m 12'1"


Height3 (To Top of FOPS Cab) 3.82 m 12'6" 3.82 m 12'6" 3.82 m 12'6"

Overall Length (with SU Blade)5 6.88 m 22'6" 6.88 m 22'6" 6.88 m 22'6"

(without Blade) 5.18 m 17'0" 5.18 m 17'0" 5.18 m 17'0"

(with SU Blade and Ripper)5 8.23 m 27'0" 8.23 m 27'0" 8.23 m 27'0"

(without Blade and Ripper) 4.91 m 16'1" 4.91 m 16'1" 4.91 m 16'1"





Universal 4.65 m 15'3" 4.65 m 15'3" 4.65 m 15'3"

Semi-U 4.31 m 14'2" 4.31 m 14'2" 4.31 m 14'2"


DEF Tank Refill Capacity — — 36 L 9.5 U.S. gal1 Product available to meet Tier 2/Stage II/Japan 2001 (Tier 2) equivalent OR Tier 3/Stage IIIA/Japan 2006 (Tier 3) equivalent emission standards.2 Operating weight includes ROPS canopy, operator, lubricants, coolant, full fuel tank, hydraulic controls and fluids, semi universal blade with tilt, back-up alarm, seat belts, lights, and single shank ripper.

— D9R equipped with track guides, ROPS/FOPS cab, single shank ripper and SU blade.3 Dimensions measured from ground line. Add grouser height for total dimension on hard surfaces.4 Height (Stripped Top) — without ROPS canopy, exhaust, seat back or other easily removed encumbrances.5 Includes drawbar.6 Per ISO 6746 — Must add grouser height for total dimension on hard surfaces.

19-16 Edition 47

19


MODEL D10T2 D11T D11T CD

Emission Standards Tier 4 Final/Stage IV/Japan 2014 (Tier 4 Final)1

Tier 4 Final/Stage IV/Japan 2014 (Tier 4 Final)1

Tier 4 Final/Stage IV/Japan 2014 (Tier 4 Final)1


Reverse Gears 538 kW 722 hp — —

Operating Weight:2

Power Shift Clutch Brake 70 171 kg 154,700 lb 104 236 kg 229,800 lb 112 718 kg 248,500 lb




Bore 137 mm 5.4" 145 mm 5.71" 145 mm 5.71"

Stroke 152 mm 6" 162 mm 6.38" 162 mm 6.38"

Displacement 27 L 1648 in3 32.1 L 1959 in3 32.1 L 1959 in3



Length of Track on Ground (Idler to Idler) 3.88 m 12'9" 4.44 m 14'7" 4.44 m 14'7"

Ground Contact Area (w/Std. Shoe) 4.74 m2 7347 in2 6.31 m2 9781 in2 8.13 m2 12,605 in2

Track Gauge 2.55 m 8'4" 2.89 m 9'6" 2.89 m 9'6"

GENERAL DIMENSIONS:

Height (Stripped Top)3 3.222 m 10'7" 3.64 m 11'11" 3.64 m 11'11"

Height (To Top of ROPS Canopy) 4.41 m 14'5" 4.70 m 15'5" 4.70 m 15'5"

Height (To Top of FOPS Cab) 4.10 m 13'5" 4.39 m 14'5" 4.39 m 14'5"

Overall Length:

(with SU Blade and SS Ripper)4 9.16 m 30'1" 10.59 m 34'9" 10.70 m 35'1"

(without Blade and Ripper)5 5.32 m 17'5" 6.16 m 20'3" 6.16 m 20'3"





CarryDozer — — 6.71 m 22'0"

Universal 5.26 m 17'3" 6.36 m 20'10" —

Semi-U 4.94 m 16'3" 5.60 m 18'4" —


Fuel Tank Refill Capacity (Extra Capacity) — 1987 L 505 U.S. gal 1987 L 505 U.S. gal1 Product available to meet Tier 2/Stage II/Japan 2001 (Tier 2) equivalent OR Tier 4 Final/Stage IV/Japan 2014 (Tier 4 Final) emission standards.2 Operating weight includes coolant, lubricants, full fuel tank, ROPS, FOPS cab, SU ABR bulldozer (D10T2) or U ABR bulldozer (D11T), dual tilt, single-shank ripper with pin-puller, fast fuel, standard ES shoes, and operator.

D11T CD has 11 Carrydozer and single-shank Carrydozer ripper.3 Height (Stripped Top) — without ROPS canopy, cab, exhaust, lift cylinders, seat back or other easily removed encumbrances.4 Overall length of D11T CD includes Straight (CarryDozer) Blade and SS Ripper.5 Overall length of machine from front tag link trunnion to rigid drawbar and excludes track grouser height.6 Per ISO 6746 — Must add grouser height for total dimension on hard surfaces.

All dimensions are approximate.

Edition 47 19-17

19-18 Edition 47

120

100

80

60

40

20

01 3 5 7 9

0 1.2 2.5 3.7 5.0 6.2

20.3

15.8

11.3

6.8

2.3

24.8

140

29.3

D3K2 XLD3K2 LGP

SPEED

DR

AW

BA

R P

UL

L

N ×1000

km/h

mph

NOTES: Usable pull will depend upon weight and traction of equipped tractor.

Assumes sufficient machine weight for <5% track slip at POR pressure.

Assumes pumps and motors are broken in.

Assumes nominal engine power and valve settings.

Drawbar pull at track stall will be lower.

lb ×1000

120

100

80

60

40

20

01 3 5 7 9

0 1.2 2.5 3.7 5.0 6.2

20.3

15.8

11.3

6.8

2.3

24.8

140

160

180

29.3

33.8

38.3

D4K2 XLD4K2 LGP

SPEED

DR

AW

BA

R P

UL

L

N ×1000

km/h

mph

lb ×1000

Drawbar Pull vs. Ground Speed● Hydrostatic Drive

Track-Type Tractors

19

Edition 47 19-19

Track-Type TractorsDrawbar Pull vs. Ground Speed● Hydrostatic Drive

NOTES: Usable pull will depend upon weight and traction of equipped tractor.

Assumes sufficient machine weight for <5% track slip at POR pressure.

Assumes pumps and motors are broken in.

Assumes nominal engine power and valve settings.

Drawbar pull at track stall will be lower.120

100

80

60

40

20

01 3 5 7 9

0 1.2 2.5 3.7 5.0 6.2

20.3

15.8

11.3

6.8

2.3

24.8

140

160

180

29.3

33.8

38.3

D5K2 XLD5K2 LGP

SPEED

DR

AW

BA

R P

UL

L

N ×1000

km/h

mph

lb ×1000

0 2 4 6 8 10

0 1 2 3 4 5 6 70

5

10

15

20

25

30

35

40

45

50

55

200

250

0

50

100

150

D6K2 XL/D6K2 LGP

SPEED

DR

AW

BA

R P

UL

L

lb ×1000

mph

km/h

N ×1000

0 2 4 6 8 10 12

0

50

100

150

200

250

300

350

0

10

20

30

40

50

60

70

80

0 1 2 4 5 6 83 7

1

3

2

D5R2 XL/LGP and D5T XLD6N XL/LGP

D6N XL/LGP Tier 4 Final/Stage IV/Japan 2014 (Tier 4 Final)

SPEED

DR

AW

BA

R P

UL

L

N ×1000

lb ×1000

mph

km/h

KEY

–––– STD- - - - XL/LGP

0 1 2 3 4 5 6 7

0

20

40

60

80

0 2 4 6 8 10 12

400

300

200

100

0

350

250

150

50

1F

2F

3F

0 1 2 3 4 5 6 7

0

20

40

60

80

0 2 4 6 8 10 12

400

300

200

100

0

350

250

150

50

1F

2F

3F

0 1 2 3 4 5 6

0

20

40

60

80

0 2 4 6 8 10

300

200

100

0

350

250

150

50

1

2

3

D6R2 Tier 2/Stage II/Japan 2001 (Tier 2) equivalent

D6R2 Tier 3/Stage IIIA/Japan 2006 (Tier 3) equivalent

SPEED SPEED

SPEED

DR

AW

BA

R P

UL

L

DR

AW

BA

R P

UL

LD

RA

WB

AR

PU

LL

lb ×1000

lb ×1000

lb ×1000

N ×1000

N ×1000

N ×1000

km/h km/h

km/h

mph mph

mph

Drawbar Pull vs. Ground Speed● Power Shift

Track-Type Tractors

19-20 Edition 47

NOTE: Usable pull will depend upon weight and traction of equipped tractor.

19

0 1 2 3 4 5 6 7

100

80

60

40

20

0

0 2 4 6 8 10 12

50

40

30

20

10

0

D7E

SPEED

DR

AW

BA

R P

UL

L

lb ×1000

kg ×1000

km/h

mph


Track-Type Tractors

Edition 47 19-21

90

80

70

60

50

40

30

20

10

00 1 2 3 4 5 6 7

40

30

20

10

0

0 2 4 6 8 10

1

2

3

D6T Tier 4 Final/Stage IV/Japan 2014 (Tier 4 Final)

SPEED

DR

AW

BA

R P

UL

L

kg ×1000

lb ×1000

mph

km/h

140

120

100

80

60

40

20

00 1 2 3 4 5 6 7 8

86420 10 12

20

10

30

40

50

0

60

1

2

3

D7R Standard/XR/LGPDifferential Steer

SPEED

DR

AW

BA

R P

UL

L

kg ×1000

lb ×1000

mph

km/h

D6T XL/XW/LGP

SPEED

DR

AW

BA

R P

UL

L

lb

mph


KEY

1 — 1st Gear2 — 2nd Gear3 — 3rd Gear

19-22 Edition 47

1

2

3

0 1 2 3 4 5 6 7 80

20

40

60

80

100

120

140

16070

60

50

40

30

20

10

0

0 2 4 6 8 10 12

D8RD8R LGP

SPEED

DR

AW

BA

R P

UL

L

kg ×1000

lb ×1000

mph

km/h

KEY



70

80

60

50

40

30

20

10

0

160

180

140

120

100

80

60

40

20

0

0 2 4 6 8 10 12

0 1 2 3 4 5 6 7 8

1

2

3

70

60

50

40

30

20

10

0

160

140

120

100

80

60

40

20

0

0 2 4 6 8 10

0 1 2 3 4 5 6 7

1

2

3

D9R Power Shift with Steering Clutches and Brakes

D8T Tier 4 Final/Stage IV/Japan 2014 (Tier 4 Final)

SPEED

SPEED

DR

AW

BA

R P

UL

L

DR

AW

BA

R P

UL

L

kg ×1000

kg ×1000

lb ×1000

lb ×1000

mph

mph

km/h

km/h

0 1 2 3 4 5 6 7

1

2

3

0 2 4 6 8 10

0

20

40

60

80

100

120

14060

50

40

30

20

10

0

D8TD8T LGP

SPEED

DR

AW

BA

R P

UL

L

kg ×1000

lb ×1000

mph

km/h


Track-Type Tractors

19

Edition 47 19-23


Track-Type Tractors

NOTE: Usable pull will depend upon weight and traction of equipped tractor. Tractors with suspended undercarriage can provide up to 15% more tractive effort than tractors with non-suspended undercarriage.

KEY


350

300

250

200

150

100

50

0

0 1 2 3 4 5 6 7 8

0

10

20

30

40

50

60

70

80

90

100

110

120

130

140

150

0 2 4 6 8 10 12

1

2

3

D11T/D11T CD

SPEED

DR

AW

BA

R P

UL

L

kg ×1000

lb ×1000

mph

km/h

250

200

150

100

50

0

0 1 2 3 4 5 6 7 8

0

10

20

30

40

50

60

70

80

90

100

110

0 2 4 6 8 10 12

1

2

3

D10T2

SPEED

DR

AW

BA

R P

UL

L

kg ×1000

lb ×1000

mph

km/h

0 1 2 3 4 5 6 7 80

20

40

60

80

100

120

140

160

180

1

2

3

0 2 4 6 8 10 12

70

60

80

50

40

30

20

10

0

D9T Differential Steering

SPEED

DR

AW

BA

R P

UL

L

kg ×1000

lb ×1000

mph

km/h

19-24 Edition 47

TRAVEL SPEED

POWER SHIFT

MODEL

D3K21

All Models

D3K2

All Models

D4K21

All Models

D4K2

All Models

D5K21

All Models

D5K2

All Models

D6K2

All Models

HYDROSTATIC km/h mph km/h mph km/h mph km/h mph km/h mph km/h mph km/h mph

FORWARD 9.0 5.6 9.0 5.6 9.0 5.6 9.0 5.6 9.0 5.6 9.0 5.6 10.0 6.2

REVERSE 10.0 6.2 10.0 6.2 10.0 6.2 10.0 6.2 10.0 6.2 10.0 6.2 10.0 6.21 Meets Tier 3/Stage IIIA/Japan 2006 (Tier 3) equivalent emission standards.

POWER SHIFT

MODEL

D5R2

Powershift

with AutoShift

D6R2

Powershift

with AutoShift D6T D7E D7E LGP D7R

FORWARD km/h mph km/h mph km/h mph km/h mph km/h mph km/h mph

1 3.3 2.1 3.8 2.4 3.8 2.3 — — — — 3.52 2.19

1.5 4.2 2.6 4.8 3.0 — — — — — — — —

2 5.8 3.6 6.5 4.1 6.5 4.0 — — — — 6.10 3.79

2.5 7.3 4.5 8.4 5.2 — — — — — — — —

3 10.1 6.3 11.5 7.1 11.3 7.0 — — — — 10.54 6.55

REVERSE

1 4.2 2.6 4.8 3.0 4.7 2.9 — — — — 4.54 2.82

1.5 5.2 3.2 6.2 3.9 — — — — — — — —

2 7.3 4.5 8.4 5.2 8.3 5.1 — — — — 7.85 4.88

2.5 7.3 4.5 8.4 5.2 — — — — — — — —

3 12.5 7.8 14.5 9.1 14.6 9.0 — — — — 13.58 8.44

ELECTRIC

FORWARD — — — — — — 11.3 7.0 11.3 7.0 — —

REVERSE — — — — — — 11.3 7.0 11.3 7.0 — —

GEAR

D6N*

Powershift with AutoShift

D6N*

Powershift with AutoShift —

Sound Suppressed

FORWARD km/h mph km/h mph

0.5 2.5 1.6 2.4 1.5

0.7 2.8 1.7 2.7 1.6

1.0 3.3 2.1 3.0 1.9

1.5 4.4 2.7 4.4 2.7

1.7 4.9 3.0 4.9 3.0

2.0 5.8 3.6 5.8 3.6

2.5 7.5 4.7 7.5 4.7

2.7 8.3 5.2 8.3 5.2

3.0 9.8 6.1 9.8 6.1

REVERSE

0.5 3.1 1.9 2.9 1.8

0.7 3.4 2.1 3.1 1.9

1.0 4.1 2.5 3.5 2.2

1.5 5.4 3.4 5.4 3.4

1.7 6.0 3.7 6.0 3.7

2.0 7.1 4.4 7.1 4.4

2.5 9.5 5.9 9.5 5.9

2.7 10.5 6.5 10.5 6.5

12.2 7.6 12.2 7.6

*Meets Tier 4 Final/Stage IV/Japan 2014 (Tier 4 Final) emission standards.

Travel SpeedTrack-Type Tractors

19

Travel Speed Track-Type Tractors

Edition 47 19-25

TRAVEL SPEED

POWER SHIFT

MODEL

Differential

Steer

D8R D8T D9R D9T D10T2 D11T/CD

D11T/CD

High Altitude

FORWARD km/h mph km/h mph km/h mph km/h mph km/h mph km/h mph km/h mph

1 3.5 2.2 3.4 2.1 3.8 2.4 3.9 2.4 4.0 2.5 3.9 2.4 4.0 2.5

2 6.2 3.9 6.0 3.7 6.8 4.2 6.8 4.2 7.2 4.5 6.8 4.2 7.0 4.4

3 10.8 6.7 10.6 6.6 11.9 7.4 11.7 7.3 12.7 7.9 11.8 7.3 12.0 7.5

REVERSE

1 4.7 2.9 4.5 2.8 4.7 2.9 4.7 2.9 5.2 3.2 4.7 2.9 4.8 3.0

2 8.1 5.0 7.9 4.9 8.4 5.2 8.4 5.2 9.0 5.6 8.2 5.1 8.3 5.2

3 13.9 8.6 14.2 8.8 14.7 9.1 14.3 8.9 15.8 9.8 14.0 8.7 14.9 9.0

GEAR

D6T

Powershift with AutoShift

D6T

Powershift with AutoShift —

Sound Suppressed

FORWARD km/h mph km/h mph

0.5 2.7 1.7 2.7 1.7

0.7 3.3 2.0 3.2 2.0

1.0 3.7 2.3 3.2 2.0

1.5 4.7 2.9 4.7 2.9

1.7 5.7 3.6 5.7 3.6

2.0 6.5 4.0 6.3 3.9

2.5 8.2 5.1 8.2 5.1

2.7 10.0 6.2 10.0 6.2

3.0 11.3 7.0 10.9 6.8

REVERSE

0.5 3.5 2.2 3.5 2.2

0.7 4.2 2.6 3.9 2.4

1.0 4.7 2.9 3.9 2.4

1.5 6.0 3.7 6.0 3.7

1.7 7.3 4.5 7.3 4.5

2.0 8.3 5.1 8.0 5.0

2.5 10.4 6.5 10.4 6.5

2.7 12.7 7.9 12.7 7.9

3.0 14.4 9.0 13.8 8.6

19-26 Edition 47

GROUND PRESSURES

Pressures computed from operating weights given earlier in this section in the specifications tables.

MODELSHOE WIDTH

CONTACT AREA

GROUND PRESSURE

mm in m2 in2 kPa psi

D3K2 XL1 406 16 1.70 2637 44.80 6.50

D3K2 LGP1 635 25 2.70 4124 29.70 4.30

D3K2 XL 406 16 1.70 2637 44.80 6.50

D3K2 LGP 635 25 2.70 4124 29.70 4.30

D4K2 XL1 460 18 2.10 3206 38.60 5.60

D4K2 LGP1 635 25 2.90 4425 29.20 4.24

D4K2 XL 460 18 2.10 3206 38.60 5.60

D4K2 LGP 635 25 2.90 4425 29.20 4.24

D5K2 XL1 510 20 2.40 3652 39.10 5.67

D5K2 LGP1 660 26 3.00 4726 31.10 4.52

D5K2 XL 510 20 2.40 3652 39.10 5.67

D5K2 LGP 660 26 3.00 4726 31.10 4.52

D5R2 XL1 560 22 2.89 4480 57.69 8.20

600 23.6 3.13 4806 53.27 7.65

610 24 3.18 4929 52.43 7.46

D5R2 LGP1 840 33 5.24 8117 35.47 5.05

865 34 5.39 8385 34.48 4.89

D5T1 560 22 2.89 4480 57.69 8.20

600 23.6 3.13 4806 53.27 7.65

610 24 3.18 4929 52.43 7.46

D6K2 XL

(Standard shoe)

510 20 2.70 4185 46.82 6.79

560 22 3.00 4650 42.13 6.11

D6K2 LGP

(Standard shoe)

610 24 3.20 4960 41.30 5.99

760 30 4.00 6200 33.02 4.79

D6N XL2 610 24 3.18 4929 51.70 7.49

D6N LGP2 840 33 5.24 8122 34.20 4.961 Meets Tier 3/Stage IIIA/Japan 2006 (Tier 3) equivalent emission standards.2 Meets Tier 4 Final/Stage IV/Japan 2014 (Tier 4 Final) emission standards.

MODELSHOE WIDTH

CONTACT AREA

GROUND PRESSURE


D6R2 STD1 560 22 2.98 4625 62.40 9.05

610 24 3.25 5038 57.28 8.31

D6R2 XL1 560 22 3.22 4984 60.70 8.80

610 24 3.50 5429 55.72 8.08

D6R2 LGP1 915 36 5.99 9290 35.40 5.13

1000 39.37 6.55 10,153 32.39 4.70

D6T XL2 560 22 3.20 4922 64.82 9.40

610 24 3.49 5369 59.43 8.62

D6T XW2 610 24 3.48 5390 61.45 8.91

710 28 4.06 6289 52.66 7.64

760 30 4.35 6738 49.15 7.13

D6T LGP2 760 30 4.98 7729 45.05 6.53

915 36 5.98 9275 37.52 5.44

991 39 6.48 10,048 34.65 5.02

D6T XL VPAT2 560 22 3.20 4922 73.1 10.60

610 24 3.49 5369 66.9 9.70

D6T XW VPAT2 710 28 4.65 7214 51.0 7.40

D6T LGP VPAT2 790 31 5.18 8034 46.2 6.701 Meets Tier 2/Stage II/Japan 2001 (Tier 2) or Tier 3/Stage IIIA/Japan 2006 (Tier 3) equivalent emission standards.

2 Meets Tier 4 Final/Stage IV/Japan 2014 (Tier 4 Final) emission standards.

NOTE: Ground contact area = width of track shoe × length of track on ground × 2.

Ground pressure =

operating weight ground contact area

Track-Type Tractors Ground Pressures

19

Ground Pressures Track-Type Tractors

Edition 47 19-27

GROUND PRESSURES

Pressures computed from operating weights given earlier in this section in the specifications tables.

MODELSHOE WIDTH

CONTACT AREA

GROUND PRESSURE


D7E1 560 22 3.37 5231 75.71 10.98◀ 610 24 3.68 5698 69.51 10.08

660 26 3.98 6165 64.24 9.32

D7E LGP1 915 36 6.31 9792 44.28 6.42

D7R ◀ 560 22 3.24 5016 75.10 10.56

610 24 3.53 5472 69.00 9.76

D7R XR ◀ 560 22 3.43 5315 70.60 10.03

610 24 3.75 5808 65.90 9.26

D7R LGP 914 36 5.82 9029 45.50 6.48

D8R ◀ 610 24 3.91 6062 95.11 13.79

660 26 4.23 6559 87.90 12.75

710 28 4.55 7056 81.48 11.81

D8R LGP 965 38 6.29 9746 54.88 7.96

D8T ◀ 610 24 3.91 6062 99.69 14.46

660 26 4.23 6559 92.14 13.36

710 28 4.55 7056 85.65 12.42

D8T LGP 965 38 6.19 9593 59.83 8.68

D8T1 610 24 3.91 6062 99.81 14.47

660 26 4.23 6559 92.25 13.38

710 28 4.55 7056 85.75 12.43

D8T LGP1 965 38 6.19 9593 59.90 8.68

◀ Standard shoe.1 Meets Tier 4 Interim/Stage IIIB/Japan 2011 (Tier 4 Interim) equivalent emis-sion standards.

MODELSHOE WIDTH

CONTACT AREA

GROUND PRESSURE


D9R/D9T 560 22 3.89 6031 121.8 17.67◀ 610 24 4.24 6569 111.80 16.22

685 27 4.74 7374 99.60 14.45

760 30 5.28 8185 89.80 13.02

D10T2 ◀ 610 24 4.74 7347 145.25 21.06

710 28 5.52 8551 124.49 18.06

760 30 5.91 9153 116.19 16.85

D11T ◀ 710 28 6.31 9781 161.98 23.49

810 32 7.20 11,159 141.99 20.59

915 36 8.13 12,605 125.69 18.23

D11T CD 810 32 7.20 11,159 153.54 22.27◀ 915 36 8.13 12,605 135.92 19.71

NOTE: Ground contact area = width of track shoe × length of track on ground × 2.

Ground pressure =

operating weight ground contact area

19-28 Edition 47

Track-Type Tractors Extreme Slope Operation

EXTREME SLOPE OPERATION

The maximum fore and aft grade in static condition on which each track-type tractor or pipelayer will main-tain proper lubrication is 45 degrees (100%). Consult Operation & Maintenance Manual (if applicable) for POWER TRAIN fluid level overfill requirements for operation on extreme slopes. Extreme slope operation is anytime the slope exceeds 25° (47%).

The ENGINE should never be overfilled with oil. This may lead to rapid overheating. For extreme slope oper-ation, engine oil should be maintained at the full mark.

NOTE: Both ENGINE and POWER TRAIN fluid levels should be checked on level ground before work-ing sidehills and slopes.

When working sidehills and slopes, consideration should be given to the following important points:

● Speed of travel — At higher speeds, inertia forces tend to make the tractor less stable.

● Roughness of terrain or surface — Ample allow ance should be made where the terrain or surface is uneven.

● Mounted equipment — Bulldozers, sidebooms, winches, and other mounted equipment cause the tractor to balance differently.

● Nature of surface — New earthen fills may give way with the weight of the tractor. Rocky surfaces may pro-mote side slipping of tractor.

● Track slippage due to excessive loads — This may cause downhill track to “dig in,” increasing angle of tractor.

● Implements hitched to the drawbar — This may decrease weight on uphill track, e.g., logging arch, two-wheel wagon.

● Height of hitch on tractor — When a high drawbar is used the tractor is less stable than with the standard drawbar.

● Width of shoes — Wide track shoes tend to decrease “digging in”, hence tractor is more stable.

● Operated equipment — Be aware of the stability and other performance features of the equipment operated by the tractor.

● Keep all attachments or pulled loads low to the ground for optimum stability.

NOTE: Safe operation on steep slopes may require special machine maintenance as well as excellent operator skill and proper equipment for the specific application. Consult Operation & Maintenance Manual (if applicable) for proper fluid level requirements.

19

CONTENTS

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-29Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-30

Features:

● Designed and built for specific tractor applications. Valves and components sized for exacting quality and performance.

● Job requirements matched through various arrange-ments.

● Hydraulic blade and ripper controls: Mechanical con-trols on G Series. Electro hydraulic controls on D6N and D6K2. Pilot blade and ripper controls on D6T Tier 3/Stage IIIA, Japan 2006 (Tier 3) equivalent with optional electro hydraulic blade con trol. Electro hydrau-lic blade and ripper controls on D6T Tier 4 Interim/Stage IIIB/Japan 2011 (Tier 4 Interim) equivalent Mechan ical con trols on D9R. Electro hydrau lic blade and ripper con trols on D7E, D8T, D9T, D10T2, and D11T.

● Full flow filters*… all oil completely filtered.

● Dual tilt — standard on D11T and D11T CD, attach-ment option on D7E, D8R, D8T, D9R, D9T, D10T2.

*Exception — D8R 2-pump.

HYDRAULIC CONTROLS

Edition 47 19-29

MODEL D3K2 D3K2 D4K2 D4K2Mounting Point Fender Fender Fender Fender

Number of Valves 3 or 4 3 or 4 3 or 4 3 or 4

Flow at 6890 kPa 73.5 L/min 19.4 gpm 73.5 L/min 19.4 gpm 73.5 L/min 19.4 gpm 73.5 L/min 19.4 gpm

(1000 psi) @ 2150 RPM @ 2150 RPM @ 2150 RPM @ 2150 RPM

Tank Capacity (Oil) 59.5 L 15.7 U.S. gal 59.5 L 15.7 U.S. gal 59.5 L 15.7 U.S. gal 59.5 L 15.7 U.S. gal

Lift Relief Valve Setting 20 600 kPa 2988 psi 20 600 kPa 2988 psi 20 600 kPa 2988 psi 20 600 kPa 2988 psi

Weight Installed:

4 Valves 39 kg 86 lb* 39 kg 86 lb* 39 kg 86 lb* 39 kg 86 lb*

MODEL D5K2 D5K2 D5R2/D5TMounting Point Fender Fender Under Operator’s

Platform

Number of Valves 3 or 4 3 or 4 2, 3, or 4

Flow at 6890 kPa 73.5 L/min 19.4 gpm 73.5 L/min 19.4 gpm 135 L/min 35.7 gpm

(1000 psi) @ 2150 RPM @ 2150 RPM @ 2200 RPM

Tank Capacity (Oil) 59.5 L 15.7 U.S. gal 59.5 L 15.7 U.S. gal 29.5 L 7.8 U.S. gal

Lift Relief Valve Setting 20 600 kPa 2988 psi 20 600 kPa 2988 psi 26 500 kPa 3843 psi

Weight Installed:

2 Valves — — 27.26 kg 60.1 lb

3 Valves — — 31.25 kg 68.9 lb

4 Valves 39 kg 86 lb* 39 kg 86 lb* 36.19 kg 79.8 lb

MODEL D6K2 D6N1 D6R23 D6R24

Mounting Point Under Operator’sPlatform

Right Rear Fender Under Operator’sPlatform

Under Operator’sPlatform

Number of Valves 3 or 4 3 or 4 2 or 3 2 or 3

Flow at 6890 kPa 120 L/min 31.7 gpm 132.5 L/min 35.0 gpm 203 L/min 53.6 gpm 188 L/min 49.7 gpm


Tank Capacity (Oil) 58 L 15.3 U.S. gal 29.5 L 7.8 U.S. gal 51.5 L 13.6 U.S. gal 51.5 L 13.6 U.S. gal

Lift Relief Valve Setting — — 19 300 kPa 2799 psi 19 300 kPa 2799 psi

XL and LGP 26 000 kPa 3771 psi 27 500 kPa 3989 psi — —

Weight Installed:

2 Valves — — 61.33 kg 135.2 lb 61.33 kg 135.2 lb

3 Valves 30 kg 66 lb 27 kg 59.5 lb 77.83 kg 171.6 lb 77.83 kg 171.6 lb

4 Valves 37 kg 81.6 lb 32 kg 70.5 lb — —

MODEL D6T D6T2 D6T VPAT2

D7E(Differential Steer)

Mounting Point Under Operator’sPlatform



Blade Control under Hood, Ripper on Rear

Number of Valves 2, 3, or 4 2, 3, or 4 3 or 4 2 Std. 4 with Ripper

Flow at 6890 kPa 205 L/min 54 gpm 205 L/min 54 gpm 205 L/min 54 gpm 204 L/min 54 gpm

(1000 psi) @ 2010 RPM @ 2010 RPM @ 2010 RPM @ 2124 RPM (PMP)

Tank Capacity (Oil) 47.3 L 12.5 U.S. gal 96 L 25.4 U.S. gal 96 L 25.4 U.S. gal 66 L 17.4 U.S. gal


Weight Installed:

2 Valves Included in Std. Tractor Included in Std. Tractor — Included in Std. Tractor

3 Valves — — Included in Std. Tractor —

*Hydraulic tank not included.1 Meets Tier 4 Final/Stage IV/Japan 2014 (Tier 4 Final) emission standards.2 Meets Tier 4 Interim/Stage IIIB/Japan 2011 (Tier 4 Interim) equivalent emission standards.3 Meets Tier 2/Stage II/Japan 2001 (Tier 2) equivalent emission standards.4 Meets Tier 3/Stage IIIA/Japan 2006 (Tier 3) equivalent emission standards.NOTE: Weight installed, two valves, includes pump, tank with filters, valves, lines, linkage, oil cooler and control levers.

19-30 Edition 47

Hydraulic Controls Specifications

19

MODELD7R

(Differential Steer) D8R D8T D9RMounting Point Under Operator’s

PlatformUnder Operator’s

PlatformAt Rear Center

of Fuel TankUnder Operator’s

Platform

Number of Valves 3 or 5 2 Std.4 with Ripper◀

Pilot Control System

2 Std., 3 with Winch, 4 with Ripper, 5 with Implement Towing AR

Electro/Hydraulic Control System

4+ Dual Tilt (Attach.)

Radiator GuardMechanical Control

System

Flow at 6890 kPa 289 L/min 76 gpm 240 L/min 63 gpm 282 L/min 74.5 gpm 239 L/min 63 gpm

(1000 psi) @ 2100 RPM @ 2100 RPM (PMP) @ 2200 RPM @ 1900 RPM

Tank Capacity (Oil) 54 L 14.3 U.S. gal 72 L 19 U.S. gal 75 L 19.8 U.S. gal 77.2 L 20.4 U.S. gal


Weight Installed 358 kg 784 lb Included in Std. Tractor Included in Std. Tractor Included in Std. Tractor

(Two Valves) (Two Valves) (Two Valves)

MODEL D9T D10T2 D11T D11T CDMounting Point Under Operator’s




Platform

Number of Valves 4+ Dual Tilt (Attach.)

Electro/Hydraulic Control System

5 Single Tilt 6 Dual Tilt

4At Rear Under

Fuel Tank1◀

+ Dual Tilt StandardRadiator Guard

4At Rear Under

Fuel Tank1◀

Dual Tilt StandardQuick Dump Valve

StandardBoth on Radiator Guard

Flow at 6890 kPa 258 L/min 68 gpm 380 L/min 100.4 gpm 620 L/min 164 gpm 670 L/min 177 gpm


Tank Capacity (Oil) 89 L 23.5 U.S. gal 131 L 34.6 U.S. gal 223 L 58.9 U.S. gal 223 L 58.9 U.S. gal

Lift Relief Valve Setting 26 200 kPa 3800 psi — — —

Lift — 28 000 kPa 4061 psi 22 753 kPa 3300 psi 24 132 kPa 3500 psi

Tilt — 20 300 kPa 2944 psi 24 304 kPa 3525 psi 24 821 kPa 3600 psi

Weight Installed Included in Std. Tractor Included in Std. Tractor Included in Std. Tractor Included in Std. Tractor

(Six Valves)

◀ Ripper valve.NOTE: Weight installed, two valves, includes pump, tank with filters, valves, lines, linkage, oil cooler and control levers.

Edition 47 19-31

Hydraulic Controls Specifications

19-32 Edition 47

Notes —

19

CONTENTS

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-33Summary of Blade Options. . . . . . . . . . . . . . . . . .19-34Blade Selection . . . . . . . . . . . . . . . . . . . . . . . . . . .19-36General Dimensions (Tractor and Blade) . . . . . . .19-39SAE Blade Capacity Definition . . . . . . . . . . . . . .19-39Blade Specifications. . . . . . . . . . . . . . . . . . . . . . . .19-40Estimating Production Off-the-Job. . . . . . . . . . . .19-50Job Condition Correction Factors . . . . . . . . . . . .19-55Measuring Production On-the-Job . . . . . . . . . . . .19-56Attachments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-56Special Attachments . . . . . . . . . . . . . . . . . . . . . . .19-57

Features:

● Straight Bulldozers — adjustable tilt angle controls blade penetration.

● Variable cutting edge Power Angle and Tilt (VPAT) — blade is available on the D3K2, D4K2, D5K2, D6K2, D6N, and D6T. The blade can be mechan-ically tipped forward for improved penetration or back for more productivity and easier finish grading.

● Angling Bulldozers — 25° right/left angling; C-frame allows mounting other tools.

● Universal Bulldozers — 25° wings provide increased capacity, less spillage.

● Semi-Universal Bulldozers — combines penetration ability of straight blade with increased load capacity provided by short 25° wings.

● Wheel Dozer blades are offered in straight and uni ver-sal blade design with hydraulic pitch and tilt control.

● Box-section construction on blades adds rigidity and strength.

● Cutting edges are heat treated and reversible for extra life.

BULLDOZERS

Edition 47 19-33

CAT BLADES SPECIAL BLADES

MODEL S U SU A FS LFS VP CD RC WC CL HU LF TW CU CPB CB VR WCB CS WCS W

D3K2 XL2 ●

D3K2 LGP2 ●

D3K2 XL ●

D3K2 LGP ●

D4K2 XL2 ●

D4K2 LGP2 ●

D4K2 XL ●

D4K2 LGP ●

D5K2 XL2 ●

D5K2 LGP2 ●

D5K2 XL ●

D5K2 LGP ●

D5E ●

D5R2 XL ● ● ● ●

D5R2 LGP ● ● ●

D5T XL ● ● ●

D6K2 XL ●

D6K2 LGP ●

D6N XL1 ● ● ●

D6N LGP1 ● ●

D6R ● ● ●

D6R XL ● ● ●

D6R LGP ● ●

D6R2 ● ● ●

D6R2 XL ● ● ●

D6R2 LGP ● ●

D6R Series 3 ● ● ● ● ● ● ●

D6R Series 3 XL ● ● ●

D6R Series 3 LGP ● ● ● ● ● ●

D6R Series 3 XW ● ● ●

D6T XL ● ● ● ● ● ●

D6T LGP ● ● ● ● ● ● ●

D6T XW ● ● ● ● ●

1 Meets Tier 4 Final/Stage IV/Japan 2014 (Tier 4 Final) emission standards.2 Meets Tier 3/Stage IIIA/Japan 2006 (Tier 3) equivalent emission standards.

19-34 Edition 47

Bulldozers SummaryBlade Options for Caterpillar Built Machines

CATERPILLAR SUPPLIED

S — Straight

U — Universal

SU — Semi-Universal

A — Angling

FS — Fill Spreading

LFS — Landfill Spreading

VP — Variable Pitch, Lower, Angle and Tilt (VPAT)

SPECIAL SUPPLIED

RC — Reclamation U TW — Two-Way Dozer

WC — Woodchips CU — Cushion Dozer

CL — Coal CPB — Cushion Push Block

HU — Heavy U CB — Coal Bowldozer

LF — Landfill VR — Variable Radius

CD — CarryDozer

WCB — Wood Chip Bowldozer

CS — Coal Scoop

WCS — Wood Chip Scoop

W — W-Blade

NOTE: This chart suggests a range of blade options for Caterpillar built machines. It is not totally inclusive of all blades available.

Edition 47 19-35

Bulldozers19

CAT BLADES SPECIAL BLADES

MODEL S U SU A FS LFS VP CD RC WC CL HU LF TW CU CPB CB VR WCB CS WCS W

D7E ● ● ● ● ●

D7E LGP ● ●

D7R ● ● ●

D7R XR ● ● ●

D7R LGP ● ●

D7R Series 2 ● ● ● ● ● ● ● ● ●

D7R Series 2 LGP ● ●

D7G Series 2 ● ● ●

D8R ● ● ● ● ● ● ● ● ● ●

D8R LGP ● ●

D8T ● ● ● ● ● ● ● ● ●

D8T LGP ● ● ●

D9R/D9T ● ● ● ● ● ● ● ● ● ●

D10T2 ● ● ● ● ● ● ● ● ●

D11T ● ● ● ●

D11T CD ●

814F ● ● ● ● ●

815F ●

816F ● ● ●

824G/824H ● ● ● ● ●

825G ●

826G/826H ● ● ●

834G/834H ● ● ● ● ● ●

836G/836H ● ●

SummaryBlade Options for Caterpillar Built Machines

CATERPILLAR SUPPLIED

S — Straight

U — Universal

SU — Semi-Universal

A — Angling

FS — Fill Spreading

LFS — Landfill Spreading

VP — Variable Pitch, Lower, Angle and Tilt (VPAT)

SPECIAL SUPPLIED

RC — Reclamation U TW — Two-Way Dozer

WC — Woodchips CU — Cushion Dozer

CL — Coal CPB — Cushion Push Block

HU — Heavy U CB — Coal Bowldozer

LF — Landfill VR — Variable Radius

CD — CarryDozer

WCB — Wood Chip Bowldozer

CS — Coal Scoop

WCS — Wood Chip Scoop

W — W-Blade

NOTE: This chart suggests a range of blade options for Caterpillar built machines. It is not totally inclusive of all blades available.

19-36 Edition 47

Bulldozers

BLADE SELECTION

Properly matching tractor and dozer is a basic require-ment for maximizing production. First consider the kind of work the tractor will be doing most of its life. Then evaluate:● Material to be moved.● Tractor limitations.

Materials to be moved

Most materials are dozeable. However, dozer perfor-mance will vary with material characteristics such as:Particle Size and Shape — The larger the individual particle size, the harder it is for a cutting edge to pene-trate. Particles with sharp edges resist the natural rolling action of a dozer blade. These particles require more horsepower to move than a similar volume of material with rounded edges.Voids — Few voids or the absence of voids means the individual particles have most or all of their surface area in contact with other particles. This forms a bond which must be broken. A well graded material, which lacks voids, is generally heavy, and will be hard to remove from the bank state.Water Content — In most materials the lack of mois-ture increases the bond between particles and makes the material difficult to remove from the bank state. A high moisture content makes dozing difficult because the material is heavy and requires more force to move. Optimum moisture reduces dust and offers the best condition for dozing ease and operator comfort.

The effect of freezing depends on the moisture con-tent. When frozen, the material’s bond strengthens as moisture content increases and temperature decreases. However, freezing a completely dry material does not change its characteristics.

An indication of a blade’s ability to penetrate and obtain a blade load is kW per meter (or horsepower per foot) of cutting edge. The higher the kW/meter (HP/foot), the more aggressive the blade. Kilowatt per Lm3 (horsepower per loose cubic yard) indicates a blade’s ability to push material. The higher the kW/Lm3 (HP/LCY), the greater the blade’s potential capa bility for carrying material at a greater speed.

Tractor Limitations

The weight and horsepower of the machine deter-mines its ability to push. No tractor can exert more pounds push than the machine itself weighs and its power train can develop. Various terrain and under-foot conditions on the job limit the tractor’s ability to use its weight and horsepower. The “approximate coef-ficient of traction factors” chart in the Tables Section presents these traction factors for common materials. To use the chart, take the total tractor weight (with attach-ments) times the factor to arrive at the maximum usable push the dozer can exert.

Production Dozing Tools

“U” — Universal blade — the large wings on this blade include one end bit and at least one section of cutting edge which make it efficient for moving big loads over long distances as in land rec-lamation, stock pile work, charging hoppers and trap-

ping for loaders. As this blade has a lower kW/meter (HP/foot) of cutting edge than an “S” or “SU”, pene-tration should not be a prime objective. With a lower kW/Lm3 (HP/LCY) than an “S” or “SU”, this blade is best for lighter or relatively easily dozed material. If equipped with tilt cylinders the U blade can be used to pry out, level, cut ditches and steer the tractor.

“SU” — The Semi-U blade combines the desir able characteristics of S and U-blades into one pack-age. It has increased capac-ity by the addition of short wings which in clude only the dozer end bits. The

wings provide improved load retention capabilities while maintaining the blade’s ability to penetrate and load quickly in tightly packed materials and to handle a wide variety of materials in production oriented appli cations. Tilt cylinder(s) increase both the produc-tivity and versatility of this dozer. Equipped with a push plate, it is effectively used for push loading scrapers.

Blade Selection● Production Dozing Toolsols

19

Edition 47 19-37

BulldozersBlade Selection● Production Dozing Tools

● General Purpose Dozing Tools ● Special Application Dozing Tools

“CD” — The CD or Carry-Dozer Blade is available for the D11T CarryDozer only. It is built to the same high standard of structural inte-grity as the “U” and “SU” Dozers. The CD Blade has

a unique “bucket” shape that allows it to carry several cubic yards or cubic meters of material in the blade. This acts as a disposable counterweight that allows the CarryDozer to push more material per pass than a standard D11T. The CarryDozer will not be as effec tive as the “U” or “SU” dozer in tightly packed or poorly shot material. It is also more sensitive to the carry-back in sticky materials.

General Purpose Dozing Tools

“S” — The Straight blade provides excellent ver sa-tility. Since it is physically smaller than the SU or U-blade, it is easier to maneu-ver and can handle a wider range of materials. It has a higher kW/ meter (HP/foot)

of cutting edge than the SU or U-blade; consequently, the “S” is more aggressive in penetrating and obtaining a blade load. A tilt cylinder increases both the produc-tiv ity and versatility of this dozer. With a high kW/Lm3

(HP/LCY), the S-blade can handle heavy material easily.

Power Angle and Tilt Blade — Versatility is its key feature with its abil-ity to perform a variety of site development to general dozing work as well as heavy-duty appli-

cations. Angle and tilt control is with 2 levers on some machines, 1 lever on others.

Variable Power Angle and Tilt (VPAT) blade can be mechanically tipped forward for improved penetration or shedding sticky material and backward for finish grading and improved productivity.

Special Application Dozing Tools

Caterpillar provides specialty bulldozers for specific applications. The blades are designed to increase production while performing certain tasks. Following are the most popular special applications blades.

Variable Radius (VR) Blades

Variable Radius Semi-U Blades are excellent tools for land im-provement, soil conservation, site development or general construction. They combine the

penetration ability of a Semi-U Blade with the load reten-tion and high capacity of a U-blade.

They provide the aggressive cutting action needed for digging, while having the material retention char ac-teristics needed for moving high volumes over a distance. This is accomplished through a moldboard which varies in radius from the edge to the center. This creates a roll-ing action in the material being moved, pushing it to the center of the blade for better retention. The extended side wings, angled to thirty degrees, further increase the capacity over a standard blade.

Angle Blade (A-Blade)

“A” — Or Angling blade can be positioned straight or angled 25 degrees to either side. It is designed for side-casting, pioneering roads,

back filling, cutting ditches and other similar tasks. It can reduce the amount of maneuvering required to do these jobs. Its “C” frame can be used for attachments such as pushing, land clearing, or snow removal tools. A-blades are not recommended for rock or severe applications.

Cushion Dozers

C u s h i o n D o z e r s a r e de signed to push-load wheel-tractor scrapers, or track-type tractors. The heavy-duty design in cludes reinforcement to transfer machine power without dam aging the blade or the

tractor. Blade cylinders are pinned to the C-frame, and the blade height is such that the blade lift cylinders are isolated from damaging forces.

The taller blade allows pushing from a higher posi-tion, eliminating blade drag and increasing produc-tivity. The blade curvature is matched to the curve of the Cat Push Block for maximum contact area, pre-vent ing the block from riding over the top of the blade. Extended side plates make it easier for operators to “catch” the stinger when repositioning for a new pass. The center of the blade is armored with T-1 plate steel for maximum service life. The narrow width of the cush-ion blade increases machine maneuverability in con-gested cuts and reduces the possibility of cutting tires associated with SU and U-blades.

When not push-loading, the dozer can be used for cut maintenance and other general dozing jobs.

Coal U-Blades are de signed specifically to move large vol-umes of coal in coal piles, at powerplants and trans-shipment points. The wing angle of thirty degrees crowds material to the center of the

blade, maximiz ing capacity by minimizing side spill. The moldboard is much higher and wider than stan dard, specifically to match the material density and loading char acteristics of coal. The curve of the mold board rolls the material forward, enhancing the carry ing capacity. With this design, coal-moving capacity can be as much as 200 percent greater than a standard U-blade.

Landfill U-Blades provide capacity increases of up to fifty percent over a straight blade. Land fill blades have the height and width to han-dle large volumes of low-density refuse, but are tough

enough to dig and bulldoze ground cover. Vision to the load is provided by areas of screen in the upper blade. Angled wings slice into natural bed earth for trenches or cover material, adding to the versatility in the landfill.

Reclamation U-Blades — are purpose-built for recla ma-tion of mine spoil piles. The blade has a larger capacity than a standard U-blade.

The wing angle of 28 degrees provides a good balance between load retention and shearing action, keeping the optimal load in front of the blade, but cutting cleanly through the material when necessary.

The width of Woodchip U-Blades gives operators max-imum control and great er confidence, even in steep chip piles. Deep cur va ture of the moldboard keeps material flowing to liven dead chips and optimize production on

long pushes. Blade height and wings angled at thirty degrees combine for excellent material retention – giv-ing better production with every pass. An operator vis-ibility window in the top section is standard.

Multi-Application/Rock and Root Rakes

Multi-Application/Rock and Root Rakes are perfectly suited for heavy duty land clearing including removal of stumps, large rocks or large trees and for work in clay and other heavy soils.

Frames are constructed of high strength steel for longer life. Cast teeth, with replaceable tips, are designed for maximum ground penetration and resistance to shock loading when prying or pushing trees, stumps and rocks. Brush rack is standard and increases height and capacity by as much as 40%.

Rake is a direct replacement for existing blade, and utilizes existing push arms and C-frames.

19-38 Edition 47

Bulldozers Blade Selection● Special Application Dozing Tools

19

Edition 47 19-39

BulldozersGeneral Dimensions Key● Tractor and Blade

● SAE Blade Capacity Definition

KEY

A Length (Blade Straight) Blade:B Width (including standard end bits)C HeightD Maximum Digging DepthE Ground Clearance @ Full LiftF Maximum Tilt (Manual)G Maximum Pitch AdjustmentH Maximum Hydraulic TiltJ Hydraulic Tilt (manual brace centered)K Push Arm Trunnion Width (to Ball Centers)

Blade capacities on the following pages are as deter-mined by SAE recommended practice J1265. Capac-ities are defined as:

Vs = 0.8 WH2.

Vu = ZH (W-Z) tan X.

Where: Vs = Capacity of straight or angling blade.

Vu = Capacity of semi-U or full U-blade.

W = Blade width exclusive of end bits.

H = Effective blade height considering tapered top corners, etc.

Z = Wing length measured parallel to blade width @ ground line of cutting edges.

X = Wing angle.

19-40 Edition 47

Bulldozers Blade Specifications● D3K2 ● D4K2 ● D5K2

MODEL

D3K2*** D4K2***

XL LGP XL LGPType Variable Power

Angling and TiltVariable PowerAngling and Tilt

Variable PowerAngling and Tilt

Variable PowerAngling and Tilt

Blade Capacities* 1.52 m3 1.99 yd3 1.66 m3 2.17 yd3 1.98 m3 2.59 yd3 1.85 m3 2.42 yd3

Weight Shipping** (Dozer) 572 kg 1261 lb 630 kg 1389 lb 642 kg 1415 lb 661 kg 1457 lb

Tractor and Dozer Dimensions:

A Length (Blade Straight) 4266 mm 168.0" 4255 mm 167.6" 4274 mm 168.3" 4266 mm 168.0"

Length (Blade Angled) 4763 mm 187.5" 4854 mm 191.1" 4795 mm 188.8" 4873 mm 191.8"

Width (Blade Angled) 2417 mm 95.1" 2874 mm 113" 2542 mm 100" 2874 mm 113"

Blade Dimensions:

B Width (including std. end bits) 2646 mm 104.1" 3149 mm 124.0" 2782 mm 109.5" 3149 mm 124.0"

C Height 910 mm 35.8" 860 mm 33.8" 1010 mm 39.8" 910 mm 35.8"

D Max. Digging Depth 573 mm 22.5" 573 mm 22.5" 572 mm 22.5" 590 mm 23.2"

E Ground Clearance @ Full Lift 730 mm 28.7" 730 mm 28.7" 743 mm 29.3" 708 mm 27.9"

G Max. Pitch Adjustment 52° to 58° 52° to 58° 52° to 58° 52° to 58°

J Hydraulic Tilt 368 mm 14.4" 438 mm 17.2" 387 mm 15.2" 438 mm 17.2"

Blade Angle 25° 25° 25° 25°

MODEL

D5K2***

XL LGPType Variable Power

Angling and TiltVariable PowerAngling and Tilt

Blade Capacities* 2.19 m3 2.86 yd3 2.34 m3 3.06 yd3

Weight Shipping** (Dozer) 706 kg 1556 lb 728 kg 1605 lb


A Length (Blade Straight) 4321 mm 170.1" 4294 mm 169.1"

Length (Blade Angled) 4864 mm 191.5" 4908 mm 193.2"

Width (Blade Angled) 2636 mm 103.8" 2940 mm 115.8"

Blade Dimensions:

B Width (including std. end bits) 2782 mm 109.5" 3220 mm 126.7"

C Height 1050 mm 41.3" 1010 mm 39.8"

D Max. Digging Depth 586 mm 23.1" 572 mm 22.5"

E Ground Clearance @ Full Lift 767 mm 30.2" 767 mm 30.2"

G Max. Pitch Adjustment 52° to 58° 52° to 58°

J Hydraulic Tilt 402 mm 15.8" 448 mm 17.6"

Blade Angle 25° 25°

***Blade capacities as determined by SAE J1265.*** Shipping Weight — Total Bulldozer Arrangement includes: Blade, push arms or C-frame, braces, cylinders, lines, trunnions and lift cylinder mountings.***Meets Tier 3/Stage IIIA/Japan 2006 (Tier 3) equivalent emission standards.

19

Edition 47 19-41

BulldozersBlade Specifications● D5R2 XL ● D5R2 LGP ● D6K2 XL ● D6K2 LGP

MODEL

D5R2 XL

ANGLE SU VPAT XLType Angle Blade Semi-Universal Variable Pitch Power

Angle and Tilt

Blade Capacities* 3.18 m3 4.16 yd3 4.28 m3 5.6 yd3 3.31 m3 4.33 yd3

Weight Shipping** (Dozer) 2546 kg 5612 lb 2600 kg 5732 lb 2375 kg 5236 lb


A Length (Blade Straight) 5193 mm 17.04' 5157 mm 16'11" 5035 mm 16'6.2"

Length (Blade Angled) 6011 mm 19.72' — 5680 mm 18'7.6"

Width (Blade Angled) 3785 mm 12.42' — 2990 mm 9'9.7"

Width (with C-Frame only) 2918 mm 9.57' — 2500 mm 8'2.4"

Blade Dimensions: (outside mounted) (outside mounted) (inside mounted)

B Width (including std. end bits) 4165 mm 13.66' 3154 mm 10'4.2" 3272 mm 10'8.8"

C Height 1034 mm 3.39' 1244 mm 4'1" 1195 mm 3'11"

D Max. Digging Depth 534 mm 1.75' 520 mm 1'8.5" 420 mm 1'4.5"

E Ground Clearance @ Full Lift 1098 mm 3.60' 983 mm 3'2.7" 1067 mm 3'6"

G Max. Pitch Adjustment — ±5° 55.7° to 62.5°

J Hydraulic Tilt — 665 mm 2'2.2" 485 mm 1'7.1"

Blade Angle 25° — 24.1°

MODEL

D5R2 LGP D6K2 XL D6K2 LGP

VPAT LGP VPAT XL VPAT LGPType Variable Pitch Power

Angle and TiltVariable Pitch Power


Angle and Tilt


Weight Shipping** (Dozer) 2740 kg 6041 lb — —


A Length (Blade Straight)*** 5398 mm 17'8.5" 5008 mm 197" 5008 mm 197"

Length (Blade Angled) 6083 mm 19'11.5" 5369 mm 211" 5399 mm 212"

Width (Blade Angled) 3727 mm 12'2.7" 2878 mm 113.3" 3337 mm 131.4"

Width (with C-Frame only) 3000 mm 9'10.1" 2330 mm 92" 2760 mm 109"

Blade Dimensions: (inside mounted)

B Width (including std. end bits) 4082 mm 13'4.7" 3196 mm 10'6" 3682 mm 12'0"

C Height 1040 mm 3'4.9" 1294 mm 50.9" 1294 mm 50.9"

D Max. Digging Depth 500 mm 1'7.7" 468 mm 18.4" 468 mm 18.4"

E Ground Clearance @ Full Lift 1052 mm 3'5.4" 1203 mm 3'10.8" 1201 mm 3'11.3"

G Max. Pitch Adjustment 54° to 62° 6° 6°

H Max. Hydraulic Tilt 585 mm 1'11" 488 mm 1'7.2" 525 mm 1'8.4"

Blade Angle 24.1° 25° 25°

*** Blade capacities as determined by SAE J1265. Notice that the capacity of the SU-blade is the volume carried by a straight blade of the same dimensions plus the volume included in the “cup” of the SU-blade. It is intended for relative comparisons of dozer sizes, and not for predicting capacities or productivities in actual field conditions.

*** Shipping Weight — Total Bulldozer Arrangement includes: Blade, push arms or C-frame, braces, cylinders, lines, trunnions and lift cylinder mountings.***With rear drawbar.

19-42 Edition 47

Bulldozers Blade Specifications● D6N XL ● D6N LGP ● D6R

MODEL

D6N XL*** D6N LGP***

6SU 6VPAT XL 6VPAT LGPType Semi-Universal Variable Pitch Power


Angle and Tilt


Weight, Shipping** (Dozer) 2600 kg 5732 lb 2375 kg 5236 lb 2740 kg 6041 lb


A Length (Blade Straight) 5157 mm 16'11" 5035 mm 16'6.2" 5398 mm 17'8.5"

Length (Blade Angled) — 5680 mm 18'7.6" 6243 mm 20'5.8"

Width (Blade Angled) — 2965 mm 116.7" 3699 mm 145.6"

Width (with C-Frame only) — 2545 mm 100" 2965 mm 116.7"

Blade Dimensions: (outside mounted) (inside mounted) (inside mounted)

B Width (including std. end bits) 3154 mm 10'4.2" 3272 mm 10'8.8" 4082 mm 13'4.7"

C Height 1244 mm 4'1" 1195 mm 3'11" 1040 mm 3'4.9"

D Max. Digging Depth 520 mm 1'8.5" 420 mm 1'4.5" 500 mm 1'7.7"

E Ground Clearance @ Full Lift 983 mm 3'2.7" 1067 mm 3'6" 1052 mm 3'5.4"

G Max. Pitch Adjustment ±5° 55.7° to 62.5° 54° to 62°

H Max. Hydraulic Tilt 665 mm 2'2.2" 485 mm 1'7.1" 585 mm 1'11"

Blade Angle — 25° 25°

MODEL

D6R

6A 6A XLGauge 1.88 m 74" 1.88 m 74"

Type Angling Angling


Weight, Shipping** (Dozer) 3195 kg 7044 lb 3195 kg 7044 lb


A Length (Blade Straight) 5.00 m 17'1" 5.21 m 17'1"

Length (Blade Angled) 5.83 m 19'2" 6.05 m 19'10"

Width (Blade Angled) 3.77 m 12'5" 3.77 m 12'5"

Width (with C-Frame only) 2.99 m 9'10" 2.99 m 9'10"

Blade Dimensions:

B Width (including std. end bits) 4.16 m 13'8" 4.16 m 13'8"

C Height 1154 mm 3'10" 1154 mm 3'10"

D Max. Digging Depth 511 mm 1'8" 511 mm 1'8"

E Ground Clearance @ Full Lift 1217 mm 4'0" 1217 mm 4'0"

F Manual Tilt — —

H Max. Hydraulic Tilt 485 mm 1'4" 485 mm 1'4"

Blade Angle 25° 25°

K Push Arm Trunnion Width

(to Ball Centers) 2.58 m 8'6" 2.58 m 8'6"

* Blade capacities as determined by SAE J1265. Tractor and dozer dimensions variations due to SystemOne undercarriage products are negligible. Notice that the capacity of the SU-blade is the volume carried by a straight blade of the same dimensions plus the volume included in the “cup” of the SU-blade. It is intended for relative comparisons of dozer sizes, and not for predicting capacities or productivities in actual field conditions.

** Shipping Weight — Total Bulldozer Arrangement includes: Blade, push arms or C-frame, braces, cylinders, lines, trunnions and lift cylinder mountings.***Meets Tier 4 Final/EU Stage IV/Japan 2014 (Tier 4 Final) emission standards.

19

Edition 47 19-43

BulldozersBlade Specifications● D6R2 ● D6T

MODEL

D6R2

6S 6SU 6SU XL 6S LGPGauge — 1880 mm 74" 1880 mm 74" 2286 mm 90"

Type Straight Semi-Universal Semi-Universal Straight


Weight, Shipping** (Dozer) 2251 kg 4963 lb 2333 kg 5143 lb 2570 kg 5666 lb 2418 kg 5331 lb


A Length (Blade Straight) 4903 mm 193.1" 5095 mm 200.6" 5332 mm 210.0" 5465 mm 215.2"

Blade Dimensions:

B Width (including std. end bits) 3360 mm 132.3" 3260 mm 128.3" 3260 mm 128.3" 4063 mm 160"

C Height 1257 mm 49.5" 1412 mm 55.6" 1412 mm 55.6" 1101 mm 43.3"

D Max. Digging Depth 473 mm 18.6" 473 mm 18.6" 459 mm 18.1" 655 mm 25.8"

E Ground Clearance @ Full Lift 1104 mm 43.5" 1104 mm 43.5" 1195 mm 47.0" 1083 mm 42.6"

G Max. Pitch Adjustment +5.3 to 4.8° +5.6 to –5.2° +5.6 to –5.2° +4.4 to –4.4°

H Max. Hydraulic Tilt 765 mm 30.1" 743 mm 29.3" 743 mm 29.3" 701 mm 27.6"


(to Ball Centers) 2640 mm 103.9" 2640 mm 103.9" 2640 mm 103.9" 3490 mm 137.4"

MODEL

D6R2 D6T

6A 6A XL 6A 6SUGauge 1880 mm 74" 1880 mm 74" 1880 mm 74" 1880 mm 74"

Type Angling Angling Angling Semi-Universal




A Length (Blade Straight) 5007 mm 197.2" 5209 mm 205.1" 5.00 m 16'5" 5.08 m 17'6"

Length (Blade Angled) — — 5.83 m 19'2" —

Width (Blade Angled) — — 3.78 m 12'5" —

Width (with C-Frame only) — — 2.93 m 9'8" —

Blade Dimensions:

B Width (including std. end bits) 4166 mm 164.0" 4166 mm 164.0" 4.16 m 13'8" 3.26 m 10'8"

C Height 1155 mm 45.5" 1155 mm 45.5" 1154 mm 3'10" 1411 mm 4'8"

D Max. Digging Depth 506 mm 19.9" 524 mm 20.6" 506 mm 1'8" 453 mm 1'6"

E Ground Clearance @ Full Lift 1142 mm 45.0" 1205 mm 47.4" 1144 mm 3'9" 1204 mm 3'11"

G Max. Pitch Adjustment 25° 25° — +5.6° to –5.2°

H Max. Hydraulic Tilt 408 mm 16.1" 408 mm 16.1" 519 mm 1'8" 811 mm 2'8"

Blade Angle — — 25° —

J Hydraulic Tilt

(Manual Brace Centered) — — — 455 mm 1'6"


(to Ball Centers) 2640 mm 103.9" 2625 mm 103.9" 2.58 m 8'6" 2.58 m 8'6"

* Blade capacities as determined by SAE J1265. Tractor and dozer dimensions variations due to SystemOne undercarriage products are negligible. Notice that the capacity of the SU-blade is the volume carried by a straight blade of the same dimensions plus the volume included in the “cup” of the SU-blade. It is intended for relative comparisons of dozer sizes, and not for predicting capacities or productivities in actual field conditions.

** Shipping Weight — Total Bulldozer Arrangement includes: Blade, push arms or C-frame, braces, cylinders, lines, trunnions and lift cylinder mountings.

19-44 Edition 47

Bulldozers Blade Specifications● D6T

MODEL

D6T

6A XL 6SU XL 6VPAT XL 6A XWGauge 1.88 m 74" 1.88 m 74" 2.13 m 84" 2.03 m 80"

Type Angling Semi-Universal VPAT Angling




A Length (Blade Straight) 5.21 m 17'1" 5.33 m 17'6" 5.39 m 17'8" 5.29 m 17'4"

Length (Blade Angled) 6.05 m 19'10" — 3.54 m 11'7" 6.20 m 20'4"

Width (Blade Angled) 3.77 m 12'5" — 3.49 m 11'5" 4.11 m 13'6"

Width (with C-Frame only) 2.99 m 9'10" — — 3.29 m 10'10"

Blade Dimensions:

B Width (including std. end bits) 4.16 m 13'8" 3.26 m 10'8" 3.88 m 12'9" 4.52 m 14'10"

C Height 1154 mm 3'10" 1407 mm 4'7" 1294 mm 4'3" 1153 mm 3'9"

D Max. Digging Depth 555 mm 1'10" 501 mm 1'7" 792 mm 2'7" 541 mm 1'9"

E Ground Clearance @ Full Lift 1112 mm 3'7" 1180 mm 3'10" 1053 mm 3'5" 1139 mm 3'9"

G Max. Pitch Adjustment — +4.0° to –4.0° +0.5° to –3.1° —

H Max. Hydraulic Tilt 424 mm 1'5" 811 mm 2'8" 410 mm 1'4" 424 mm 1'5"

Blade Angle 25° — 24° 25°

J Hydraulic Tilt

(Manual Brace Centered) — 455 mm 1'6" — —


(to Ball Centers) 2.58 m 8'6" 2.58 m 8'6" — 2.89 m 9'8"

MODEL

D6T

6SU XW 6A LGP 6S LGP 6VPAT LGP/XWGauge 2.03 m 80" 2.29 m 90" 2.29 m 90" 2.29 m 90"

Type Semi-Universal Angling Straight VPAT





Length (Blade Angled) — 6.81 m 22'4" — —

Width (Blade Angled) — 4.63 m 15'2" — 3.72 m 12'2"

Width (with C-Frame only) — 3.77 m 12'5" — —

Blade Dimensions:





G Max. Pitch Adjustment +4.0° to –4.0° — +4.4° to –4.4° +0.5° to –3.1°


Blade Angle — 24.2° — 24°

J Hydraulic Tilt

(Manual Brace Centered) 442 mm 1'5" — 399 mm 1'4" —


(to Ball Centers) 2.89 m 9'8" 3.42 m 11'5" 3.42 m 11'5" —

* Blade capacities as determined by SAE J1265. Notice that the capacity of the SU-blade is the volume carried by a straight blade of the same dimensions plus the volume included in the “cup” of the SU-blade. It is intended for relative comparisons of dozer sizes, and not for predicting capacities or productivities in actual field conditions.

** Shipping Weight — Total Bulldozer Arrangement includes: Blade, push arms or C-frame, braces, cylinders, lines, trunnions and lift cylinder mountings.

19

Edition 47 19-45

BulldozersBlade Specifications● D7E ● D7R

● D7R XR ● D7R LGP

MODEL

D7E

7A 7S 7SU 7UType Angling Straight Semi-Universal Universal





Length (Blade Angled) 7.07 m 23'2" — — —

Width (Blade Angled) 4.12 m 13'6" — — —

Width (with C-Frame only) 3.40 m 11'2" — — —

Blade Dimensions:





G Max. Pitch Adjustment — 52° to 58° 52° to 58° 52° to 58°

Blade Angle (either side) 25° — — —


J Hydraulic Tilt

(Manual Brace Centered) — 530 mm 1'9" 500 mm 1'8" 550 mm 1'10"


(to Ball Centers) 2.81 m 9'2" 2.81 m 9'2" 2.81 m 9'2" 2.81 m 9'2"

MODEL

D7E D7R/D7R XR D7R LGP

7S LGP 7SU 7A 7SType Straight Semi-Universal Angling Straight




A Length (Blade Straight) 6.28 m 20'7" 6.03 m 19'9" 4218 mm 13'10" 5.81 m 19'1"

Length (Blade Angled) — — 5098 mm 16'9" —

Width (Blade Angled) — — 4114 mm 13'6" —

Width (with C-Frame only) — — 3073 mm 10'1" —

Blade Dimensions:

B Width (including std. end bits) 4.59 m 15'1" 3.69 m 12'1" 4503 mm 14'9" 4.50 m 14'9"

C Height 1351 mm 4'5" 1524 mm 5'0" 1111 mm 3'8" 1343 mm 4'4.9"

D Max. Digging Depth 631 mm 2'1" 527 mm 1'8.7" 647 mm 2'1" 668 mm 2'2.3"

E Ground Clearance @ Full Lift 1292 mm 4'3" 1145 mm 3'9.1" 1340 mm 4'5" 1153 mm 3'9.4"

G Max. Pitch Adjustment 54° to 60° +3.1° to 3.9° — +3.0° to 3.9°

Blade Angle (either side) 778 mm 2'7" — 25°

H Max. Hydraulic Tilt 468 mm 1'7" 799 mm 2'7.4" 466 mm 1'6" 686 mm 2'3"

J Hydraulic Tilt

(Manual Brace Centered) 3.35 m 11'0" 474 mm 18.6" 627 mm 2'1" 426 mm 16.8"


(to Ball Centers) — 2.87 m 9'5" 2795 mm 9'2" 3.37 m 11'1"

* Blade capacities as determined by SAE J1265. Notice that the capacity of the U-blade is the volume carried by a straight blade of the same dimensions plus the volume included in the “cup” of the U-blade. It is intended for relative comparisons of dozer sizes, and not for predicting capacities or productivities in actual field conditions.

Notice that the capacity of the SU-blade is the volume carried by a straight blade of the same dimensions plus the volume included in the “cup” of the SU-blade. It is intended for relative comparisons of dozer sizes, and not for predicting capacities or productivities in actual field conditions.

**Shipping Weight — Total Bulldozer Arrangement includes: Blade, push arms or C-frame, braces, cylinders, lines, trunnions and lift cylinder mountings.

19-46 Edition 47

Bulldozers Blade Specifications● D8R ● D8T

MODEL

D8R/D8T

8A 8SU 8U 8SU LGPType Angling Semi-U Universal Semi-U


Weight, Shipping** (Dozer) 5121 kg 11,289 lb 4260 kg 9392 lb 4895 kg 10,793 lb 4703 kg 10,368 lb


A Length (Blade Straight) 6.57 m 21'7" 6.39 m 21'0" 6.79 m 22'3" 6281 mm 20'7"

Length (Blade Angled) 7.62 m 25'0" — — —

Width (Blade Angled) 4.52 m 14'10" — — —

Width (with C-Frame only) 3.38 m 11'1" — — —

Blade Dimensions:



D Max. Digging Depth 625 mm 2'1" 511 mm 20.1" 567 mm 1'10" 513 mm 1'9"

E Ground Clearance @ Full Lift 1323 mm 4'3" 1310 mm 4'4" 1239 mm 4'1" 1308 mm 4'3.5"

G Max. Pitch Adjustment — +3.0° to 2.9° +3.0° to 2.9° —

Blade Angle (either side) 25° — — —


J Hydraulic Tilt

(Manual Brace Centered) — 585 mm 1'11" 635 mm 2'1" —


(to Ball Centers) 2983 mm 9'9" 2983 mm 9'9" 2983 mm 9'9" 3329 mm 10'11"

Maximum Track Width Permitted 710 mm 2'4" 710 mm 2'4" 710 mm 2'4" 965 mm 3'2"

Dual Tilt Option

G Dual Pitch Adj. — ±4.6° ±4.6° —

H Dual Max. Hyd. Tilt — 879 mm 2'11" 950 mm 3'1" —




19

Edition 47 19-47

BulldozersBlade Specifications● D9R ● D9T

MODEL

D9R/D9T

9SU 9UType Semi-U Universal


Weight, Shipping** (Dozer) 6863 kg 15,130 lb 7388 kg 16,288 lb


A Length (Blade Straight) 6.60 m 21'6" 6.96 m 22'8"

Blade Dimensions:


C Height 1934 mm 6'4.1" 1934 mm 6'4.1"

D Max. Digging Depth 606 mm 1'11.9" 606 mm 1'11.9"

E Ground Clearance @ Full Lift 1422 mm 4'8" 1422 mm 4'8"

G Max. Pitch Adjustment +3.4° to 2.9° +3.4° to 2.9°

H Max. Hydraulic Tilt 940 mm 3'1" 1014 mm 3'3.9"

J Hydraulic Tilt

(Manual Brace Centered) 570 mm 1'10.4" 616 mm 2'0.3"



Maximum Track Width Permitted 762 mm 2'6" 762 mm 2'6"

Dual Tilt Option

G Dual Pitch Adj. +4.8° to 5.2° +4.8° to 4.9°

H Dual Max. Hyd. Tilt 1139 mm 3'8.8" 1231 mm 4'0.5"




MODEL

D10T2

10SU 10UType Semi-U Universal


Weight, Shipping**

Standard Dozer 10 229 kg 22,550 lb 10 784 kg 23,775 lb

Abrasion Dozer 11 069 kg 24,403 lb 12 413 kg 27,366 lb


A Length 7.37 m 24'2" 7.73 m 25'4"

Width 4.86 m 15'11" 5.26 m 17'3"

Blade Dimensions:


C Height 2.12 m 6'11" 2.12 m 6'11"

D Max. Digging Depth 674 mm 2'2.5" 674 mm 2'2.5"

E Ground Clearance @ Full Lift 1497 mm 4'10.9" 1497 mm 4'10.9"

G Max. Pitch Adjustment +1.7° to 2.3° +1.7° to 2.3°

H Max. Hydraulic Tilt 993 mm 3'3.1" 1074 mm 3'6.3"

J Hydraulic Tilt

(Manual Brace Centered) 722 mm 2'4.4" 782 mm 2'6.8"



Maximum Track Width Permitted 762 mm 2'6" 762 mm 2'6"

Dual Tilt Option

G Dual Pitch Adjustment +5.2° to 5.5° +5.2° to 5.5°

H Dual Max. Hyd. Tilt 1441 mm 4'8.7" 1560 mm 5'1.4"

**Blade capacities as determined by SAE J1265. ** Notice that the capacity of the U-blade is the volume carried by a straight blade of the same dimensions plus the volume included in the “cup” of the U-blade.

It is intended for relative comparisons of dozer sizes, and not for predicting capacities or productivities in actual field conditions. Notice that the capacity of the SU-blade is the volume carried by a straight blade of the same dimensions plus the volume included in the “cup” of the SU-blade.

It is intended for relative comparisons of dozer sizes, and not for predicting capacities or productivities in actual field conditions.**Shipping Weight — Total Bulldozer Arrangement includes: Blade, push arms or C-frame, braces, cylinders, lines, trunnions and lift cylinder mountings.


19-48 Edition 47

Bulldozers Blade Specifications● D10T2

19

Edition 47 19-49

BulldozersBlade Specifications● D11T

MODEL

D11T

11SU 11U 11 CDType Semi-U Universal CarryDozer


Weight, Shipping**

Standard Dozer 14 813 kg 32,658 lb 17 296 kg 38,131 lb 24 085 kg 53,099 lb

Abrasion Dozer 16 192 kg 35,698 lb 18 823 kg 41,498 lb —


A Length 8.58 m 28'2" 8.64 m 28'4" 8.77 m 28'9"

Width 5.50 m 18'1" 6.26 m 20'7" 6.43 m 21'1"

Blade Dimensions:

B Width (including std. end bits) 5.58 m 18'4" 6.35 m 20'10" 6.71 m 22'0"

C Height 2.75 m 9'0" 2.83 m 9'3" 2.96 m*** 9'8"***

D Max. Digging Depth 766 mm 2'6.2" 766 mm 2'6.2" 688 mm 2'3"

E Ground Clearance @ Full Lift 1533 mm 5'0.4" 1533 mm 5'0.4" 1850 mm 6'1"

G Max. Pitch Adjustment +2.1° to 2.2° +2.1° to 2.2° —

H Max. Hydraulic Tilt 1184 mm 3'10.6" 1344 mm 4'4.9" 1800 mm 5'11''

J Hydraulic Tilt

(Manual Brace Centered) 886 mm 2'10.9" 1006 mm 3'3.6" —


(to Ball Centers) 4.18 m 13'9" 4.18 m 13'9" 4.18 m 13'9"

Maximum Track Width Permitted 914 mm 3'0" 914 mm 3'0" 914 mm 3'0"

Dual Tilt Option +7.5° to 7.6° +7.5° to 7.6°

or or

G Dual Pitch Adjustment +0° to 13° +0° to 13° +47.8° to 10.4°

H Dual Max. Hyd. Tilt 1706 mm 5'7.2" 1938 mm 6'4.3" —

***Blade capacities as determined by SAE J1265. *** Notice that the capacity of the U-blade is the volume carried by a straight blade of the same dimensions plus the volume included in the “cup” of the U-blade.

It is intended for relative comparisons of dozer sizes, and not for predicting capacities or productivities in actual field conditions. Notice that the capacity of the SU-blade is the volume carried by a straight blade of the same dimensions plus the volume included in the “cup” of the SU-blade.

It is intended for relative comparisons of dozer sizes, and not for predicting capacities or productivities in actual field conditions.***Shipping Weight — Total Bulldozer Arrangement includes: Blade, push arms or C-frame, braces, cylinders, lines, trunnions and lift cylinder mountings.***Blade height with cutting edge at 53°.


19-50 Edition 47

Bulldozers Estimating Production Off-the-Job

BULLDOZER PRODUCTION OFF-THE-JOB

You can estimate bulldozer production using the pro-duction curves that follow and the correction factors that are applicable. Use this formula:

Production (Lm3/hr)(LCY/hr)

=Maximum production

×Correction

factors

The bulldozer production curves give maximum uncor-rected production for universal, semi-universal, and straight blades and are based on the following conditions:

1. 100% efficiency (60 minute hour — level cycle).2. Power shift machines with 0.05 min. fixed times.3. Machine cuts for 15 m (50 feet), then drifts blade

load to dump over a high wall. (Dump time — 0 sec.)4. Soil density of 1370 kg/Lm3 (2300 lb/LCY).5. Coefficient of traction:* a. Track machines — 0.5 or better b. Wheel machines — 0.4 or better6. Hydraulic controlled blades used.7. Dig 1F** Carry 2F** Return 2R**

To obtain estimated production in bank cubic meters or bank cubic yards, appropriate load factor from the Tables section should be applied to the corrected pro-duc tion as calculated above.

Production Bm3/hr=

Lm3/hr × LF(BCY/h) (LCY/h) × LF

*Coefficient of traction assumed to be at least 0.4. While poor traction affects both track and wheel vehicles, causing them to take smaller blade loads, wheeled units are affected more severely and production falls much more rapidly. While no fixed rules can predict this production loss, a rough rule of thumb is that wheel dozer production falls off 4% for each one-hundredth decrease in coefficient of traction below 0.40. If, for example, coefficient of traction is 0.30, the difference is ten-hundredths (0.10), and production is 60% (10 × 4% = 40% decrease).

**This gear sequence is based on level to downhill terrain, light to medium density material, and no blade extensions such as spill plates, rock guards, etc. Exceeding these condi-tions may require carry in 1F, but productivity should equal or exceed “standard conditions” due to the larger loads that can be carried in 1F.

19

Edition 47 19-51

BulldozersEstimating Production Off-the-Job● U-Blades

0

200

400

600

800

1000

1200

1400

1600

1800

2000

2200

2400

2600

2800

3000

3200

3400

3600

3800

4000

4200

4400

4600

4800

5000

5200

0 100 200 300 400 500 600

0810 120 1506030 90

2700

1500

0

1800

1200

900

3900

3600

3300

3000

300

600

2400

2100

A

B

C

D

E

F

Meters

KEY

A — D11T CDB — D11TC — D10T2D — D9TE — D8TF — D7E

NOTE: This chart is based on numerous field studies made under varying job conditions. Refer to correction factors follow ing these charts.

Lm3/hr LCY/hr

AVERAGE DOZING DISTANCE

Feet

ES

T. D

OZ

ING

PR

OD

UC

TIO

N

ESTIMATED DOZING PRODUCTION ● Universal Blades ● D7E through D11T CD

19-52 Edition 47

Bulldozers Estimating Production Off-the-Job● SU-Blades


ESTIMATED DOZING PRODUCTION ● Semi-Universal Blades ● D7E through D11T

KEY

A — D11TB — D10T2C — D9TD — D8TE — D7E

0

200

400

600

800

1000

1200

1400

1600

1800

2000

2200

2400

2600

2800

3000

3200

3400

3600

3800

0 100 200 300 400 500 600

2700

2400

1500

2100

1800

300

600

0

1200

900

60 08109030 150120

A

D

C

E

B

Meters

Lm3/hr LCY/hr


Feet

ES

T. D

OZ

ING

PR

OD

UC

TIO

N

Edition 47 19-53

Bulldozers19

Estimating Production Off-the-Job● SU-Blades


ESTIMATED DOZING PRODUCTION ● Semi-Universal Blades ● D6N through D8R

KEY

A — D8RB — D7RC — D6T Tier 4 Interim/Stage IIIB/Japan 2011 (Tier 4 Interim)D — D6TE — D6RF — D6N

0

100

200

300

400

500

600

700

800

900

1000

1100

1200

0 100 200 300 400 500 600

60 08109030 150120

900

600

0

300

A

F

CDE

B

Meters

Lm3/hr LCY/hr


Feet

ES

T. D

OZ

ING

PR

OD

UC

TIO

N

19-54 Edition 47

Bulldozers Estimating Production Off-the-Job● S-Blades


ESTIMATED DOZING PRODUCTION ● Straight Blades ● D6T through D7E

KEY

A — D7EB — D6T

0

100

200

300

400

500

600

700

800

0 50 100 150 200 250 300 350

500

600

0

300

100

200

400

5030 4020 001010 70 908060

A

B

Meters

Lm3/hr LCY/hr


Feet

ES

T. D

OZ

ING

PR

OD

UC

TIO

N

19

Edition 47 19-55

BulldozersJob FactorsEstimating Production Off-the-Job

● Example Problem

JOB CONDITION CORRECTION FACTORS

TRACK-TYPE TRACTOR

OPERATOR —

Excellent 1.00

Average 0.75

Poor 0.60

MATERIAL —

Loose stockpile 1.20

Hard to cut; frozen —

with tilt cylinder 0.80

without tilt cylinder 0.70

Hard to drift; “dead” (dry, non-

cohesive material) or very sticky

material

0.80

Rock, ripped or blasted 0.60-0.80

SLOT DOZING 1.20

SIDE BY SIDE DOZING 1.15-1.25

VISIBILITY —

Dust, rain, snow, fog or darkness 0.80

JOB EFFICIENCY —

50 min/hr 0.83

40 min/hr 0.67

BULLDOZER*

Adjust based on SAE capacity relative to the base blade used in the Estimated Dozing Production graphs.

GRADES — See following graph.

*NOTE: Angling blades and cushion blades are not considered production dozing tools. Depending on job conditions, the A-blade and C-blade will average 50-75% of straight blade production.

% Grade vs. Dozing Factor

(–) Downhill(+) Uphill

1.8

1.6

1.4

1.2

1.0

.8

.6

.4

.2

–30 –20 –10 0 +10 +20 +30

ESTIMATING DOZER PRODUCTION OFF-THE-JOB

Example problem:

Determine average hourly production of a D8T/8SU (with tilt cylinder) moving hard-packed clay an average distance of 45 m (150 feet) down a 15% grade, using a slot dozing technique.

Estimated material weight is 1600 kg/Lm3 (2650 lb/LCY). Operator is average. Job efficiency is estimated at 50 min/hr.

Uncorrected Maximum Production — 458 Lm3/h (600 LCY/hr) (example only)

Applicable Correction Factors:

Hard-packed clay is “hard to cut” material . . .–0.80 Grade correction (from graph) . . . . . . . . . . . . .–1.30 Slot dozing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .–1.20 Average operator . . . . . . . . . . . . . . . . . . . . . . . .–0.75 Job efficiency (50 min/hr) . . . . . . . . . . . . . . . . .–0.83 Weight correction. . . . . . . . . . . . . . (2300/2650)–0.87

Production = Maximum Production × Correction Factors

= (600 LCY/hr) (0.80) (1.30) (1.20) (0.75) (0.83) (0.87)

= 405.5 LCY/hr

To obtain production in metric units, the same proce-dure is used substituting maximum uncorrected pro duc-tion in Lm3.

= 458 Lm3/h × Factors = 309.6 Lm3/h

19-56 Edition 47

Bulldozers Measuring ProductionOn-the-Job● Attachments

MEASURING PRODUCTION ON-THE-JOB

Three generally accepted methods of measuring bull-dozer production are listed below. The third method is empirical, but is the simplest to conduct.1. Employing Surveying Techniques a. Conduct time study and then cross-section the

cut to determine the volume of material removed. (Production in Bm3 or BCY per unit of time)

b. Conduct time study and then cross-section the fill to determine the volume of fill material. (Produc-tion in Lm3 or LCY per unit of time)

2. Weighing Blade Loads Conduct time study and weigh material moved

by bulldozer by weighing the loader bucket loads.3. Measuring Blade Loads a. Dozer operation (1) Pick up and carry load onto a level area and

stop. (2) Raise the blade directly over the pile pulling

forward slightly as blade comes up, leaving a nearly symmetrical pile.

(3) Reverse to clear the pile. b. Measurements (1) The average height (H) of the pile in feet. Hold

the tape vertically at the inside edge of each grouser mark. Sight along top of the pile to obtain the correct measurement.

(2) The average width (W) of the pile in feet. Hold the tape horizontally over the pile and sight at the inside edge of each grouser mark and the corresponding opposite side of the pile.

(3) The greatest length (L) of the pile in feet. Hold the tape horizontally over the pile and sight at each end of the pile.

c. With the above measurements, now compute the blade load.

(1) Average the height measurement (H) (2) Average the width measurement (W) (3) Load (Lm3 or LCY) = 0.0138 × (HWL) (4) Load (Bm3 or BCY) = Lm3 or LCY × LF d. Combine the calculated blade load with time

study to figure production.

VARIABLE RADIUS (VR) SEMI-U BLADES D6T D7R D8R/D8TCapacity 5.81 m3 7.6 yd3 7.84 m3 10.25 yd3 11.28 m3 14.75 yd3

Width 3349 mm 11'0" 3912 mm 12'10" 4369 mm 14'4"

Height 1473 mm 4'10" 1626 mm 5'4" 1778 mm 5'10"

Weight 1360 kg 3000 lb 2000 kg 4400 lb 3010 kg 6640 lb

LANDFILL BLADES D6T D7E D7RCapacity 12.5 m3 16.4 yd3 14 m3 18.4 yd3 18.1 m3 23.7 yd3

Width 3886 mm 12'9" 3713 mm 12'2" 4267 mm 14'0"

Height 1796 mm 5'10.7" 1524 mm 5'0" 2083 mm 6'10"


LANDFILL BLADES D8R/D8T D9R/D9TCapacity 24.4 m3 32 yd3 38.5 m3 50.3 yd3

Width 4928 mm 16'2" 5442 mm 17'10"

Height 2286 mm 7'6" 2178 mm 7'1.75"

Weight 3175 kg 7000 lb 4900 kg 10,800 lb

This list is not all inclusive. Contact your Cat dealer for special attachment needs.

TOP VIEW SIDE VIEW

GROUSER MARKS

ATTACHMENTS

19

Edition 47 19-57

BulldozersSpecial Attachments● Coal U-Blades ● Woodchip Dozers

● Reclamation U-Blades ● Cushion Dozers

COAL U-BLADES D6T D7E D7E LGPCapacity 9.7 m3 12.63 yd3 14.8 m2 19.4 yd2 14.8 m2 19.4 yd2

Width 4267 mm 14'0" 4902 mm 193" 4902 mm 193"

Height 1473 mm 4'10" 1778 mm 70" 1778 mm 70"


COAL U-BLADES D8R/D8T D9R/D9T D10T2 D11TCapacity 21.4 m3 28 yd3 37 m3 48 yd3 46.1 m3 60.3 yd3 74.9 m3 98.0 yd3

Width 5537 mm 18'2" 5940 mm 18'10" 6191 mm 20'1" 7416 mm 24'4"

Height 1930 mm 6'4" 2540 mm 8'4" 2794 mm 9'2" 3330 mm 10'11"

Weight 3200 kg 7050 lb 4490 kg 9900 lb 6670 kg 14,700 lb 11 340 kg 25,000 lb

WOODCHIP DOZERS D6T D7E D7E LGPCapacity 15 m3 20 yd3 23.5 m2 30.8 yd2 23.5 m2 30.8 yd2

Width 4267 mm 14'0" 4902 mm 193" 4902 mm 193"

Height 1880 mm 6'2" 2286 mm 90" 2286 mm 90"


WOODCHIP DOZERS D8R/D8T D9R/D9T D10T2Capacity 28.3 m3 37 yd3 45.9 m3 60 yd3 72.6 m3 95 yd3

Width 5486 mm 18'0" 5486 mm 18'0" 6300 mm 20'8"

Height 2337 mm 7'8" 3086 mm 10'1.5" 3480 mm 11'5"

Weight 2903 kg 6400 lb 5080 kg 11,200 lb 7575 kg 16,700 lb

RECLAMATION U-BLADES D8R/D8T D9R/D9T D10T2Capacity 16.4 m3 21.5 yd3 20.9 m3 27.3 yd3 30.6 m3 40 yd3

Width 4877 mm 16'0" 5182 mm 17'0" 5664 mm 18'7"

Height 1880 mm 6'2" 2032 mm 6'8" 2388 mm 7'10"

Weight 3810 kg 8400 lb 5220 kg 11,500 lb 6440 kg 14,200 lb

CUSHION DOZERS D8R/D8T D9R/D9T D10T2 D11TWidth 2889 mm 9'5.75" 3048 mm 10'0" 3505 mm 11'6"

Height 1499 mm 4'11" 1575 mm 5'2" 1676 mm 5'6" *

Weight 3185 kg 7020 lb 4310 kg 9500 lb 6440 kg 14,200 lb

Rear Cushion

Push Block * 2175 kg 4800 lb 3105 kg 6850 lb *

*Available upon request.This list is not all inclusive.

19-58 Edition 47

Notes —

19

CONTENTS

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-59Ripper Specification Diagrams Adjustable Parallelogram Ripper . . . . . . . . . . .19-60 Radial Ripper . . . . . . . . . . . . . . . . . . . . . . . . . .19-62 Fixed Parallelogram Ripper . . . . . . . . . . . . . . .19-62Specifications Track-Type Tractors . . . . . . . . . . . . . . . . . . . . .19-63Tip Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-73Estimating Ripping Production . . . . . . . . . . . . . .19-73Seismic Wave Velocity Charts . . . . . . . . . . . . . . . .19-76Estimated Ripper Production Graphs . . . . . . . . .19-81

Features:

● Parallelogram linkage with hydraulically variable pitch on D7E, D7R, D8R/D8T, D9R/D9T, D10T2 and D11T. Operator can adjust angle of ripper tip to the material for penetra tion at all ripping depths to increase production.

● Fixed Parallelogram linkage design used on D3K2, D4K2, D5K2, D6K2, D6N, D6R, D6R XL, D6T and D6T XL. This design holds tooth angle constant at all ripping depths.

● Adjustable Single shank arrangements available for D8R/D8T, D9R/D9T, D10T2 and D11T for tough rip ping applications and deep ripping requirements.

● Hydraulically Variable Pitch Multi-shank arrange ments available on D7E, D7R, D8R/D8T, D9R/D9T, D10T2 and D11T allow wide-beam coverage in easier-to-rip materials.

● Counterweighted CarryDozer Ripper single shank avail able for D11T and D11T CD, multi-shank avail-able for D11T CD.

RIPPERS

Edition 47 19-59

“Pryout,” (Breakout) kilonewtons (and pounds) — the maximum sustained upward force, generated by the lift cylinders measured at the ripper tip. Break out force is measured with the shank in the top hole, shank vertical and ripper full down. Break out force may be hydrau li-cally or balance limited.

“Penetration force,” kilonewtons (and pounds) — the max imum sustained downward force, generated by the ripper lift cylinders measured at the ripper tip, which is required to raise the back end of the vehicle with the tip on ground and the shank (pinned in the top hole) vertical.

19-60 Edition 47

Rippers Specification Diagrams● Adjustable Parallelogram Ripper

DEFINITION OF FORCES SHOWN IN TABLES THAT FOLLOW

Adjustable Parallelogram Ripper

NOTE: Letters correspond to ripper specifications on pages that follow.

KEY

AA — Ground Line

19

Adjustable Parallelogram Ripper

Edition 47 19-61

RippersSpecification Diagrams● Adjustable Parallelogram Ripper


KEY

AA — Ground LineBB — Track Gauge

19-62 Edition 47

Rippers Specification Diagrams● Radial Ripper● Fixed Parallelogram Ripper


KEY

AA — Ground Line * — Tip Standard

Radial Ripper*

Fixed Parallelogram Ripper

19

TRACTOR/RIPPER D3K2** D3K2 D4K2**Ripper Type Fixed Parallelogram Fixed Parallelogram Fixed Parallelogram

Dimensions:

Ripper Shank

G Maximum digging depth 338 mm 13.3" 338 mm 13.3" 338 mm 13.3"

L Maximum reach at ground line 766 mm 30.2" 766 mm 30.2" 596 mm 23.5"

M Maximum ground clearance under tip

(shank pinned in bottom hole) 448 mm 17.6" 448 mm 17.6" 448 mm 17.6"

N Maximum ramp angle, ripper up

(shank pinned in bottom hole) 27° 27° 32°

Shank section 36 × 76 mm 1.4" × 3" 36 × 76 mm 1.4" × 3" 36 × 76 mm 1.4" × 3"

Ripper Beam

O Overall width 1710 mm 67.3" 1710 mm 67.3" 1710 mm 67.3"

P Height 165 mm 6.5" 165 mm 6.5" 165 mm 6.5"

Q Length 190 mm 7.5" 190 mm 7.5" 190 mm 7.5"

Number of Pockets 3 3 3

T Pocket Spacing 775 mm 30.5" 775 mm 30.5" 775 mm 30.5"

U Shank Gauge 1550 mm 61.0" 1.55 m 61.0" 1550 mm 61.0"

V Track clearance with standard shoe 80 mm 3.2" 80 mm 3.2" 80 mm 3.2"

Installed weights:

Ripper with standard shank 554 kg 1222 lb 554 kg 1222 lb 554 kg 1222 lb

Ripper Forces:*

Penetration Force 22.1 kN 4970 lb 22.1 kN 4970 lb 24.7 kN 5560 lb

Pryout Force 44.0 kN 9900 lb 44.0 kN 9900 lb 44.0 kN 9900 lb

TRACTOR/RIPPER D4K2 D5K2** D5K2Ripper Type Fixed Parallelogram Fixed Parallelogram Fixed Parallelogram

Dimensions:

Ripper Shank

G Maximum digging depth 338 mm 13.3" 338 mm 13.3" 338 mm 13.3"

L Maximum reach at ground line 766 mm 30.2" 555 mm 21.9" 766 mm 30.2"


(shank pinned in bottom hole) 448 mm 17.6" 448 mm 17.6" 448 mm 17.6"


(shank pinned in bottom hole) 27° 33° 27°

Shank section 36 × 76 mm 1.4" × 3" 36 × 76 mm 1.4" × 3" 36 × 76 mm 1.4" × 3"

Ripper Beam

O Overall width 1710 mm 67.3" 1710 mm 67.3" 1710 mm 67.3"

P Height 165 mm 6.5" 165 mm 6.5" 165 mm 6.5"

Q Length 190 mm 7.5" 190 mm 7.5" 190 mm 7.5"


T Pocket Spacing 775 mm 30.5" 775 mm 30.5" 775 mm 30.5"

U Shank Gauge 1.55 m 61.0" 1550 mm 61.0" 1.55 m 61.0"


Installed weights:


Ripper Forces:*

Penetration Force 22.1 kN 4970 lb 27.3 kN 6130 lb 22.1 kN 4970 lb

Pryout Force 44.0 kN 9900 lb 44.0 kN 9900 lb 44.0 kN 9900 lb

*This value may vary slightly with various vehicle configurations.**Meets Tier 3/Stage IIIA/Japan 2006 (Tier 3) equivalent emission standards.NOTE: Letters correspond to ripper dimension drawings.

Edition 47 19-63

Rippers Specifications● D3K2 ● D4K2 ● D5K2

TRACTOR/RIPPER D5R2 XL/D5R2 LGP D6K2 XLRipper Type Parallelogram Fixed Parallelogram

Dimensions:

Ripper Shank

G Maximum digging depth 355 mm 14.0" 355 mm 14.0"

L Maximum reach at ground line 516 mm 1'8.3" 725 mm 28.5"


(shank pinned in bottom hole) 422 mm 16.6" 471 mm 18.5"


(shank pinned in bottom hole) 21.4° 24.8°

Ripper Beam

O Overall width 2200 mm 7'3" 1951 mm 6'4.8"

P Height 216 mm 8.5" 165 mm 6.5"

Q Length 254 mm 10" 211 mm 8.3"

Number of Pockets 3 3

T Pocket Spacing 1000 mm 3'3.4" 896 mm 2'11.3"

U Shank Gauge 2000 mm 6'7" 1792 mm 5'10.6"

V Track clearance with standard shoe 99 mm 3.9" 81 mm 3.2"

Installed weights:

Ripper with standard shank 1406 kg 3100 lb 908 kg 2002 lb

Each additional shank 78 kg 172 lb 34 kg 75 lb

Ripper Forces:

Penetration Force 51.6 kN 11,600 lb 43 kN 9666.8 lb

Pryout Force 211.2 kN 47,480 lb 170 kN 38,218 lb

NOTE: Letters correspond to ripper dimension drawings.

19-64 Edition 47

Rippers Specifications● D5R2 XL ● D5R2 LGP ● D6K2 XL

19

Edition 47 19-65

Rippers Specifications● D6K2 LGP ● D6R2

TRACTOR/RIPPER D6K2 LGP D6R2Ripper Type Fixed Parallelogram Parallelogram

Dimensions:

Ripper Shank

G Maximum digging depth 355 mm 14.0" 495 mm 1'8"

L Maximum reach at ground line 725 mm 28.5" 733 mm 2'5"


(shank pinned in bottom hole) 471 mm 18.5" 518 mm 1'8"


(shank pinned in bottom hole) 24.8° 26°

Shank section — 74 × 175 mm 2.9" × 6.9"

Ripper Beam

O Overall width 1951 mm 6'4.8" 2.20 m 7'3"

P Height 165 mm 6.5" 216 mm 8.5"

Q Length 211 mm 8.3" 254 mm 10"


T Pocket Spacing 896 mm 2'11.3" 1000 mm 3'3"

U Shank Gauge 1792 mm 5'10.6" 2 m 6'7"


Installed weights:



Ripper Forces:*

Penetration Force 46 kN 10,641 lb 65.6 kN 14,747 lb

Pryout Force 170 kN 38,218 lb 89.6 kN 20,140 lb

* D6R2 tractor equipped with ripper, OROPS, SU dozer and heavy duty track. Values may vary slightly with various configurations.NOTE: Letters correspond to ripper dimension drawings.

19-66 Edition 47

Rippers Specifications● D6R2 XL ● D6R2 LGP

TRACTOR/RIPPER D6R2 XL D6R2 LGPRipper Type Parallelogram Parallelogram

Dimensions:

Ripper Shank

G Maximum digging depth 495 mm 1'8" 445 mm 1'6"

L Maximum reach at ground line 733 mm 2'5" 586 mm 1'11"


(shank pinned in bottom hole) 518 mm 1'8" 568 mm 1'10"


(shank pinned in bottom hole) 26° 28.5°

Shank section 74 × 175 mm 2.9" × 6.9" 74 × 175 mm 2.9" × 6.9"

Ripper Beam

O Overall width 2.20 m 7'3" 2.20 m 7'3"

P Height 216 mm 8.5" 216 mm 8.5"

Q Length 254 mm 10" 254 mm 10"


T Pocket Spacing 1000 mm 3'3" 1000 mm 3'3"

U Shank Gauge 2 m 6'7" 2 m 6'7"


Installed weights:



Ripper Forces:*

Penetration Force 65.6 kN 14,747 lb 65.6 kN 14,747 lb

Pryout Force 116.5 kN 20,140 lb 116.5 kN 20,140 lb

* Tractor equipped with ripper, OROPS, SU dozer and heavy duty track. Values may vary slightly with various configurations.NOTE: Letters correspond to ripper dimension drawings.

19

Edition 47 19-67

RippersSpecifications● D6T XL ● D6T XW ● D6T LGP

TRACTOR/RIPPER D6T XL** D6T XW** D6T LGP**Ripper Type Parallelogram Parallelogram Parallelogram

Dimensions:

Ripper Shank

G Maximum digging depth 495 mm 1'8" 495 mm 1'8" 445 mm 1'6"

VPAT 495 mm 1'8" 445 mm 1'6" 445 mm 1'6"

L Maximum reach at ground line 733 mm 2'5" 733 mm 2'5" 586 mm 1'11"

VPAT 733 mm 2'5" 586 mm 1'11" 586 mm 1'11"


(shank pinned in bottom hole) 518 mm 1'8" 518 mm 1'8" 568 mm 1'10"

VPAT 518 mm 1'8" 568 mm 1'10" 568 mm 1'10"


(shank pinned in bottom hole) 26° 26° 28.5°

VPAT 26° 28.5° 28.5°

Shank section 74 × 175 mm 2.9" × 6.9" 74 × 175 mm 2.9" × 6.9" 74 × 175 mm 2.9" × 6.9"

Ripper Beam

O Overall width 2.20 m 7'3" 2.20 m 7'3" 2.20 m 7'3"

P Height 216 mm 8.5" 216 mm 8.5" 216 mm 8.5"

Q Length 254 mm 10" 254 mm 10" 254 mm 10"


T Pocket Spacing 1000 mm 3'3" 1000 mm 3'3" 1000 mm 3'3"

U Shank Gauge 2 m 6'7" 2 m 6'7" 2 m 6'7"


VPAT 374 mm 1'3" 374 mm 1'3" 374 mm 1'3"

Installed weights:


Each additional shank 73 kg 160 lb 73 kg 160 lb 73 kg 160 lb

Ripper Forces:*

Penetration Force 15.6 kN 3,507 lb 67.7 kN 15,220 lb 72.4 kN 16,276 lb

Pryout Force 116.5 kN 26,190 lb 116.5 kN 26,190 lb 116.5 kN 26,190 lb

* Tractor equipped with ripper, cab, SU dozer, and standard track.**Meets Tier 4 Final/Stage IV/Japan 2014 (Tier 4 Final) emission standards.NOTE: Letters correspond to ripper dimension drawings.

19-68 Edition 47

Rippers

TRACTOR/RIPPER D7RRipper Type Adjustable Parallelogram

Dimensions:

Ripper Shank

G Maximum digging depth 748 mm 2'5.4"

L Maximum reach at ground line 1.07 m 3'6.1"

M Maximum ground clearance under tip (shank pinned in bottom hole) 638 mm 2'1.1"

N Maximum ramp angle, ripper up (shank pinned in bottom hole) 26.6°

Shank section 72 × 228 mm 2.8" × 6.9"

Ripper Beam

O Overall width 2.21 m 7'3"

P Height 279 mm 11"

Q Length 343 mm 13.5"

Number of Pockets 3

T Pocket Spacing 991 mm 3'3"

U Shank Gauge 1.98 m 6'6"

V Track clearance with standard shoe 95 mm 3.7"

Installed weights:

Ripper with standard shank 3277 kg 7225 lb

Each additional shank 138 kg 305 lb

Ripper Forces:*

Penetration Force 85.0 kN 19,104 lb

Pryout Force 176.6 kN 39,705 lb

* Tractor equipped with ripper, OROPS, SU dozer and heavy duty track. Values may vary slightly with various configurations.NOTE: Letters correspond to ripper dimension drawings.

Specifications● D7R

Edition 47 19-69

Rippers19

TRACTOR/RIPPER D7E D8R/D8T

Ripper Type

Adjustable Parallelogram Adjustable Parallelogram

Multi-shank Single Shank Multi-shank

Dimensions:

Ripper to Track

Ripper length behind track,

shank vertical, ripper up

A With Pushblock N/A N/A N/A

B Without Pushblock 1222 mm 4'0" 1.69 m 5'7" 1.6 m 5'2"


shank vertical, ripper down

C With Pushblock N/A N/A N/A

D Without Pushblock 1660 mm 5'5" 1.84 m 6'0" 1.71 m 5'7"

Tip to track distance, shank vertical

E Ripper Up 614 mm 2'0" 694 mm 2'3.3" 640 mm 2'1.2"

F Ripper Down 970 mm 3'2" 950 mm 3'1.4" 899 mm 2'11.4"

Ripper Shank*

G Maximum digging depth 650 mm 2'2" 1130 mm 3'8.5" 780 mm 2'6.7"

H Dig adjustment per hole 230 mm 9" 305 mm 12" 250 mm 10"

I Total dig adjustment 230 mm 9" 610 mm 2'0" 250 mm 10"

Pitch Adjustment, ripper down:

J Forward 16° 15° 14.9°

K Backward 12° 9.9° 10°

L Maximum reach at ground line 1156 mm 3'10" 1.32 m 4'3" 1.17 m 3'10"

M Maximum ground clearance under tooth

(shank pinned in bottom hole) 588 mm 1'11" 636 mm 2'1" 593 mm 1'11.3"


(shank pinned in bottom hole) 26° 28.2° 28.4°

Shank Section 72 × 228 mm 2.8" × 9.0" 75 × 333 mm 2.9" × 13.1" 75 × 333 mm 2.9" × 13.1"

Ripper Beam

O Overall width 2088 mm 6'10" N/A 2.46 m 8'1"

P Height** 355.6 mm 14" N/A 334 mm 13.1"

(dia) (dia)

Q Length** — N/A 457 mm 18"

Clearance under beam, shank vertical

R Ripper Up 1080 mm 3'7" N/A 1.55 m 5'1"

S Ripper Down 145 mm 5.7" N/A 449 mm 17.7"


T Pocket Spacing 900 mm 2'11" N/A 1092 mm 3'7"

U Shank Gauge 1800 mm 5'11" N/A 2.17 m 7'1"

V Track Clearance with standard shoe 47 mm 1.9" 76 mm 3" 76 mm 3"

W Width across widest part of lift cylinders 1275 mm 4'2" 1.37 m 4'5" 1.37 m 4'5"

Installed Weights:


Each additional tooth group 150 kg 330 lb N/A 332 kg 730 lb

Ripper Forces:***

Penetration Force, shank vertical 87.4 kN 19,639 lb 127.4 kN 28,620 lb 124.2 kN 27,920 lb

Pryout Force, shank vertical 234.4 kN 52,695 lb 222.8 kN 50,070 lb 227.9 kN 51,230 lb

*** Deep Ripping Shank is available for D8R/D8T single shank rippers. Hydraulic pin puller is standard with deep ripping shank. Deep Ripping Arrangement maximum digging depth is 1.57 m (5'2") for D8R/D8T.

***D7E ripper beam circular cross section.*** Forces for D7E are for machine equipped with SU-blade and standard track. Forces for D8R/D8T are for a ripper on a tractor equipped with EROPS, U-Dozer

and performance track. Forces will vary slightly with other vehicle configurations.NOTE: Letters correspond to ripper dimension drawings.

Specifications● D7E ● D8R/D8T

TRACTOR/RIPPER D9R/D9T

Ripper Type

Adjustable Parallelogram

Single Shank Multi-shank

Dimensions:

Ripper to Track


shank vertical, ripper up

A With Pushblock N/A N/A

B Without Pushblock 1.57 m 5'2" 1.33 m 4'4"


shank vertical, ripper down

C With Pushblock N/A N/A

D Without Pushblock 1.88 m 6'2" 1.71 m 5'7"

Tip to track distance, shank vertical

E Ripper Up 689 mm 2'3.2" 510 mm 1'8.1"

F Ripper Down 944 mm 3'1.2" 890 mm 2'11"

Ripper Shank*

G Maximum digging depth 1231 mm 4'0.6" 798 mm 2'7.6"

H Dig adjustment per hole 295 mm 12" 250 mm 10"

I Total dig adjustment 590 mm 1'11.2" 250 mm 10"


J Forward 10.6° 10°

K Backward 15.2° 15.1°

L Maximum reach at ground line 1.25 m 4'1" 1.16 m 3'10"


(shank pinned in bottom hole) 882 mm 2'10.9" 879 mm 2'10.6"



Shank Section 90 × 355 mm 3.5" × 14" 75 × 332 mm 2.9" × 13.1"

Ripper Beam

O Overall width N/A 2.64 m 8'8"

P Height N/A 380 mm 15"

Q Length N/A 457 mm 18"


R Ripper Up N/A 1.77 m 5'10"

S Ripper Down N/A 393 mm 15.5"


T Pocket Spacing N/A 1176 mm 3'10.3"

U Shank Gauge N/A 2.35 m 7'8"

V Track Clearance with standard shoe 71 mm 2.8" 71 mm 2.8"

W Width across widest part of lift cylinders 1.50 m 4'11" 1.50 m 4'11"

Installed Weights:


Each additional tooth group N/A 347 kg 765 lb

Ripper Forces:**

Penetration Force, shank vertical 158 kN 35,520 lb 154 kN 34,621 lb

Pryout Force, shank vertical 332 kN 74,637 lb 361 kN 81,156 lb

** Deep Ripping Shank is available for D9R/D9T single shank rippers. Hydraulic pin puller is standard with deep ripping shank. Deep Ripping Arrangement maximum digging depth is 1.66 m (5'5") for D9R/D9T.

** Forces are for a ripper on a tractor equipped with EROPS, U-Dozer and performance track. Forces will vary slightly with other vehicle configurations.NOTE: Letters correspond to ripper dimension drawings.

19-70 Edition 47

Rippers Specifications● D9R/D9T

19

TRACTOR/RIPPER D10T2 D11T D11T

Ripper Type

Adjustable Parallelogram Adjustable Parallelogram

Single Shank Multi-shank Single Shank CD Single Shank

Dimensions:

Ripper to Track


shank vertical, ripper up (A)

A With Pushblock 2.08 m 6'10" N/A 2.29 m 7'6" N/A

B Without Pushblock 1.76 m 5'9" 1.56 m 5'1" 1.97 m 6'6" 2.26 m 7'5"


shank vertical, ripper down (A)

C With Pushblock 2.48 m 8'2" N/A 2.71 m 8'11" N/A

D Without Pushblock 2.16 m 7'1" 1.96 m 6'5" 2.39 m 7'10" 2.52 m 8'3"

Tip to track distance, shank vertical (A)

E Ripper Up* 730 mm 2'4.7" 651 mm 2'1.6" 751 mm 2'6" 751 mm 2'6"

F Ripper Down** 1130 mm 3'8.5" 1050 mm 3'5.3" 1174 mm 3'10" 1174 mm 3'10"

Ripper Shank***

G Maximum digging depth** 1504 mm 4'11" 950 mm 3'1.4" 1612 mm 5'3" 1612 mm 5'3"

H Dig adjustment per hole 355 mm 14" 250 mm 10" 280 mm 11" 280 mm 11"

I Total dig adjustment 710 mm 2'4" 250 mm 10" 840 mm 2'9.1" 840 mm 2'9.1"


J Forward 15.4° 18.1° 15° 13°

K Backward 29.7° 23.2° 31.9° 31.9°

L Maximum reach at ground line** 1.60 m 5'3" 1.39 m 4'7" 1.87 m 6'2" 1.87 m 6'2"

M Maximum ground clearance under

tooth (shank pinned in bottom hole) 912 mm 3'0" 1055 mm 3'5.5" 1111 mm 3'9.7" 1115 mm 3'8"


(shank pinned in bottom hole) 35.7° 50.9° 34.1° 34.1°

Shank Section 100 × 400 mm 90 × 355 mm 110 × 450 mm 110 × 450 mm

(4" × 15.75") (3.5" × 14") (4.3" × 17.7") (4.3" × 17.7")

Ripper Beam

O Overall width N/A 2.92 m 9'7" N/A N/A

P Height N/A 468 mm 18.4" N/A N/A

Q Length N/A 485 mm 19.1" N/A N/A


R Ripper Up N/A 2.03 m 6'8" N/A N/A

S Ripper Down N/A 380 mm 15" N/A N/A

Number of Pockets 1 3 1 1

T Pocket Spacing N/A 1320 mm 4'4" N/A N/A

U Shank Gauge N/A 2.63 m 8'8" N/A N/A

V Track Clearance with standard shoe 97 mm 4" 97 mm 4" 141 mm 5.6" 141 mm 5.6"

W Width across widest part

of lift cylinders 1.75 m 5'9" 1.75 m 5'9" 1.90 m 6'3" 1.90 m 6'3"

Installed Weights:

Ripper with standard shank 6445 kg 14,209 lb 6132 kg 13,519 lb 8817 kg 19,438 lb 12 461 kg 27,472 lb

Each additional tooth group N/A 544 kg 1200 lb N/A N/A

Ripper Forces:****

Penetration Force, shank vertical 219 kN 49,233 lb 208 kN 46,760 lb 350 kN 78,683 lb 381 kN 85,652 lb

Pryout Force, shank vertical 512 kN 115,102 lb 515 kN 115,777 lb 638 kN 143,428 lb 629 kN 141,405 lb

****With Standard Shank pinned in the bottom hole. ****With Standard Shank pinned in the top hole. **** Deep Ripping Shank is available for the D10T2 and D11T single shank rippers. Deep Ripping Arrangement maximum digging depth is 1.80 m (5'11") for

the D10T2 and 2.17 m (7'1") for the D11T.**** Forces are for a ripper on a tractor equipped with an EROPS, U-Dozer and performance track. Forces will vary slightly with other machine configurations.All dimensions are approximate.

Edition 47 19-71

Rippers Specifications● D10T2 ● D11T

TRACTOR/RIPPER D11T D11T

Ripper Type

Adjustable Parallelogram

Multi-shank CD Multi-shank

Dimensions:

Ripper to Track


shank vertical, ripper up (A)

A With Pushblock N/A N/A

B Without Pushblock 1.69 m 5'6" 1.71 m 5'8"


shank vertical, ripper down (A)

C With Pushblock N/A N/A

D Without Pushblock 2.16 m 7'1" 2.16 m 7'1"

Tip to track distance, shank vertical (A)

E Ripper Up 0.78 m 2'7" 0.78 m 2'7"

F Ripper Down 1.95 m 6'5" 1.96 m 6'5"

Shank*

G Maximum digging depth 1100 mm 3'7.3" 1100 mm 3'7.3"

H Dig adjustment per hole 280 mm 11" 280 mm 11"

I Total dig adjustment 280 mm 11" 280 mm 11"


J Forward 12.2° 12.2°

K Backward 31.8° 31.8°

L Maximum reach at ground line 1.71 m 5'7" 1.71 m 5'7"


(shank pinned in bottom hole) 1090 mm 3'6.9" 1090 mm 3'6.9"



Shank Section 100 × 400 mm 3.9" × 15.7" 100 × 400 mm 3.9" × 15.7"

Ripper Beam

O Overall width 3.33 m 10'11" 3.34 m 10'11.5"

P Height 560 mm 22" 595 mm 23.4"

Q Length 560 mm 22" 595 mm 23.4"


R Ripper Up 2.06 m 6'9" 2.03 m 6'8"

S Ripper Down 282 mm 11.1" 247 mm 9.7"


T Pocket Spacing 1.5 m 4'11" 1.5 m 4'11"

U Shank Gauge 3.0 m 9'10" 3.0 m 9'10"

V Track Clearance with standard shoe 166 mm 5.6" 166 mm 5.6"

W Width across widest part of lift cylinders 1.9 m 6'3" 1.9 m 6'3"

Installed Weights:

Ripper with standard shank 8674 kg 19,123 lb 11 790 kg 25,993 lb

Each additional tooth group 689 kg 1519 lb 689 kg 1519 lb

Ripper Forces:**

Penetration Force, shank vertical 335 kN 75,311 lb 365 kN 82,055 lb

Pryout Force, shank vertical 632 kN 142,079 lb 636 kN 142,978 lb

** Hydraulic pin puller is standard with deep ripping shank. Deep Ripping Arrangement maximum digging depth is 2.18 m (7'2").** Forces are for a ripper on a tractor equipped with an EROPS, U-Dozer and performance track. Forces will vary slightly with other vehicle configurations.

19-72 Edition 47

Rippers Specifications● D11T

19

Edition 47 19-73

RippersTip SelectionEstimating Production

TIP SELECTION FOR THE D8R/D8T, D9R/D9T, D10T2 AND D11T RIPPERS

Three tip configurations (short, intermediate and long) in two styles (centerline and penetration) are available for economical operation in a variety of conditions.

RECOMMENDED TIP USAGE

Short — Use in high impact conditions where break age problems occur. The shorter the tip, the more it resists breakage.

Intermediate — Most effective in moderate impact con-ditions where abrasion is not excessive.

Long — Use in loose, abrasive materials where break -age is not a problem. Generally offers the most wear material.

Centerline vs Penetration

The materials being ripped and the tractor doing the ripping will both have an effect on which tip will do the best job. High density material requires a “penetration” tip. High impact material requires a “centerline” tip. The following is a general guide to tip application.

Tips to use

Ripping ConditionD8R/D8T D9R/D9T D10T2 D11T

Tandem Tractors . . . . . . . . . Short Short Short

Single Shank and Multi-shank

Extreme Duty. . . . . . . . . . Int. Short Short

Medium Duty. . . . . . . . . . Long Int. Int.

Abrasive Duty . . . . . . . . . Long Long Long

Always use the longest tip that will wear without exces-sive breakage. Different tips should be tried to determine the most economical.

ESTIMATING RIPPING PRODUCTION

Ripping costs must be compared to other methods of loosening the material — usually drilling and blast-ing — on a cost per ton or bank cubic yard basis. Thus, an accurate estimation of ripper production is needed to determine unit ripping costs.

There are three general methods of estimating ripping production:

1. The best method is to record the time spent ripping, then remove (using scrapers or loaders and trucks) and weigh the ripped material. The total weight divided by the time spent will give hourly pro duc-tion. If the contractor is paid by volume, then a density must be used and the accuracy is only as good as the density used. For payment by volume removed, method 2 may be desirable. Some care will be needed to assure that only ripped material is removed.

2. Another method is to cross-section the area and then record the time spent ripping. After the mate-rial has been removed, cross-section the area again to determine the volume of rock removed. The vol-ume divided by the time spent ripping gives the rip-ping rate per minute or hour.

3. Timing the ripper over a measured distance is the least accurate method, but valuable for quick esti-mating on the job. An average cycle time should be determined from a number of timed cycles. Turn-around or back-up time must be included. Measure the average rip distance, rip spacing and depth of penetration. This data will give the volume per cycle from which the production in bank cubic yards can be calculated. Experience has shown results obtained from this method are about 10 to 20% higher than the more accurate method of cross-sectioning.

An example of the measured distance method for calculating ripper production is:

Data — D10T2 — No. 10 with one shank. 910 mm (36 in) between passes. 1.6 km/h (1 mph) average speed (including slippage

and stalls).Every 91 m (300 ft) requires 0.25 min to raise, pivot, turn, and lower again: 91 m (300 ft) = 1 pass.610 mm (24 in) penetration.Full time ripping (no pushing or dozing assignment).

19-74 Edition 47

Rippers Estimating Production

Example of Estimating Production (Metric)

Time per pass:

1.6 km/h = 26.7 m/min. Then 91 m

= 3.41 min; 26.7 m/min

3.41 min + 0.25 min (turn time) = 3.66 min/pass.

If the operator works an average of 45 min per h, it is

possible to make = 45

= 12.3 passes per h 3.66

Volume ripped: 91 m × 0.9 m × 0.6 m = 49.1 BCM per pass

Production = 49.1 × 12.3 = 604 BCM per h

Remember the results from this method are usually 10 to 20 per cent higher than the actual production that can be expected on the job.

● ● ●

Example of Estimating Production (English)

Time per pass:

MPH = 88 fpm. Then 300 ft

= 3.41 min; 88 fpm

3.41 min + 0.25 min. (turn time) = 3.66 min/pass.

If the operator works an average of 45 min per h, it is

possible to make = 45

= 12.3 passes per h 3.66

Volume ripped: 300 × 3 × 2

= 66.7 BCY per pass 27

Production = 66.7 × 12.3 = 820 BCY per hr

● ● ●

NOTE: The demands of heavy ripping will increase the normal owning and operating costs of the tractor.

These costs should be increased no less than 30-40% in heavy ripping applications to estimate rock loosen -ing costs.

There is no ready answer or rule-of-thumb solution to predict ripping production. Even if everything is known about the seismic velocity of the material, its composi-tion, job conditions, equipment and operator, only a “guess timate” can be given. The final answer must come from a production study obtained on the job site.

Sample problem (Metric)

Determine the loosening costs in the following situation:

Machine — D10T2 Tractor with No. 10

Single Shank RipperRip Spacing — 915 mmRipper Penetration — 610 mmRip Distance — 91 mRip Time — 3.41 minutesManeuver Time — 0.25 minutesSeismic Velocity — 1830 meters per secondAssume 60 min. hour

Solution:

1. Total Cycle Time = 3.41 + 0.25 = 3.66 min

Cycles/hour = 60 min/hr

= 16.4 3.66 min/cycle

2. Production per cycle = 91 m × 0.9 m × 0.6 m = 49.1 BCM/cycle

3. Production = 49.1 BCM/cycle × 16.4 cycles/h = 805 BCM/h

4. Remember results of this method are usually 10 to 20% high.

Actual Production = 80% of 805 BCM/h = 644 BCM/h Or 90% of 805 BCM/h = 725 BCM/h

5. Owning and Operating Costs A D10T2 (ripping only) could have a $115.00/h O & O costs including $30/h operator. 6. Loosening Costs $115.00/hr ÷ 644 BCM/h = $0.179/BCM $115.00/hr ÷ 725 BCM/h = $0.159/BCM The loosening cost should range from 15.9¢ to

17.9¢/BCM

● ● ●

Sample problem (English)

Determine the loosening costs in the following situation:

Machine — D10T2 Tractor with No. 10 Single Shank Ripper

Rip Spacing — 3 feetRipper Penetration — 2 feetRip Distance — 300 feetRip Time — 3.41 minutesManeuver Time — 0.25 minutesSeismic Velocity — 6000 feet per secondAssume 60 min. hour

19

Edition 47 19-75

RippersEstimating ProductionUsing Seismic Charts

Solution:

1. Total Cycle Time = 3.41 + 0.25 = 3.66 min

Cycles/hour = 60 min/hr

= 16.4 3.66 min/cycle

2. Production per cycle = 300 × 3 × 2

= 66.7 BCY/cycle 27

3. Production = 66.7 BCY/cycle × 16.4 cycles/hr = 1094 BCY/hour

4. Remember results of this method are usually 10 to 20% high.

Actual Production = 80% × 1094 = 875 BCY/hr or 90% × 1094 = 984 BCY/hr

5. Owning and Operating Costs A D10T2 (ripping only) could have a $115.00/hr O & O costs including $30/hr operator

6. Loosening Costs $115.00/hr ÷ 875 BCY/hr = $0.131/BCY $115.00/hr ÷ 984 BCY/hr = $0.117/BCY The loosening cost should range from 11.7¢ to 13.1¢/BCY

● ● ●

USE OF SEISMIC VELOCITY CHARTS

The charts of ripper performance estimated by seis-mic wave velocities have been developed from field tests conducted in a variety of materials. Con sidering the extreme variations among materials and even among rocks of a specific classification, the charts must be rec-ognized as being at best only one indicator of rippability.

Accordingly, consider the following precautions when evaluating the feasibility of ripping a given formation:

— Tooth penetration is often the key to ripping suc-cess, regardless of seismic velocity. This is partic-u larly true in homogeneous materials such as mudstones and claystones and the fine-grained caliches. It is also true in tightly cemented forma-tions such as conglomerates, some glacial tills and caliches containing rock fragments.

— Low seismic velocities of sedimentaries can indi-cate probable rippability. However, if the fractures and bedding joints do not allow tooth penetra-tion, the material may not be ripped effectively.

— Pre-blasting or “popping” may induce sufficient fracturing to permit tooth entry, particularly in the caliches, conglomerates and some other rocks; but the economics should be checked carefully when considering popping in the higher grades of sandstones, limestones and granites.

Ripping is still more art than science, and much will depend on operator skill and experience. Ripping for scraper loading may call for different techniques than if the same material is to be dozed away. Cross-ripping requires a change in approach. The number of shanks used, length and depth of shank, tooth angle, direc-tion, throttle position — all must be adjusted according to field conditions. Ripping success may well depend on the operator finding the proper combination for those conditions.

Ripper Performance● D8R/D8T

19-76 Edition 47

Rippers

D8R/D8T● Multi- or Single Shank No. 8 Ripper

● Estimated by Seismic Wave Velocities

11111 51 61 2 3 4 7 8 9 10 11 12 13 14 15

2 3 410

TOPSOIL

CLAY

GLACIAL TILL

IGNEOUS ROCKS GRANITE

BASALT

TRAP ROCK

SEDIMENTARY ROCKS SHALE

SANDSTONE

SILTSTONE

CLAYSTONE

CONGLOMERATE

BRECCIA

CALICHE

LIMESTONE

METAMORPHIC ROCKS

SCHIST

SLATE

MINERALS and ORES

COAL

IRON ORE

Seismic Velocity

Meters Per Second × 1000

Feet Per Second × 1000

RIPPABLE MARGINAL NON-RIPPABLE

19

Edition 47 19-77

RippersRipper Performance● D9R/D9T

D9R/D9T● Multi- or Single Shank No. 9 Ripper


11111 51 61 2 3 4 7 8 9 10 11 12 13 14 15

2 3 410

TOPSOIL

CLAY

GLACIAL TILL

IGNEOUS ROCKS GRANITE

BASALT

TRAP ROCK

SEDIMENTARY ROCKS SHALE

SANDSTONE

SILTSTONE

CLAYSTONE

CONGLOMERATE

BRECCIA

CALICHE

LIMESTONE

METAMORPHIC ROCKS

SCHIST

SLATE

MINERALS and ORES

COAL

IRON ORE


Seismic Velocity



19-78 Edition 47

Rippers Ripper Performance● D10T2

D10T2● Multi- or Single Shank No. 10 Ripper


11111 51 61 2 3 4 7 8 9 10 11 12 13 14 15

2 3 410

TOPSOIL

CLAY

GLACIAL TILL

IGNEOUS ROCKS

GRANITE

BASALT

TRAP ROCK

SEDIMENTARY ROCKS

SHALE

SANDSTONE

SILTSTONE

CLAYSTONE

CONGLOMERATE

BRECCIA

CALICHE

LIMESTONE

METAMORPHIC ROCKS

SCHIST

SLATE

MINERALS and ORES

COAL

IRON ORE

Seismic Velocity




19

Edition 47 19-79

RippersRipper Performance● D11T

D11T● Multi- or Single Shank No. 11 Ripper


11111 51 61 2 3 4 7 8 9 10 11 12 13 14 15

2 3 410

GLACIAL TILL

IGNEOUS ROCKS

GRANITE

BASALT

TRAP ROCK

SEDIMENTARY

SHALE

SANDSTONE

SILTSTONE

CLAYSTONE

CONGLOMERATE

BRECCIA

CALICHE

LIMESTONE

METAMORPHIC

SCHIST

SLATE

MINERALS and ORES

COAL

IRON ORE

Seismic Velocity




19-80 Edition 47

Rippers Ripper Performance● D11T CD

D11T CD● Single Shank No. 11 Ripper


11111 51 61 2 3 4 7 8 9 10 11 12 13 14 15

2 3 410

GLACIAL TILL

IGNEOUS ROCKS

GRANITE

BASALT

TRAP ROCK

SEDIMENTARY

SHALE

SANDSTONE

SILTSTONE

CLAYSTONE

CONGLOMERATE

BRECCIA

CALICHE

LIMESTONE

METAMORPHIC

SCHIST

SLATE

MINERALS and ORES

COAL

IRON ORE

Seismic Velocity




19

Edition 47 19-81

RippersEstimated Ripper Production Graphs● D8R/D8T ● D9R/D9T

CONSIDERATIONS FOR USING PRODUCTION ESTIMATED GRAPHS:

● Machine rips full-time — no dozing.

● Power shift tractors with single shank rippers.

● 100% efficiency (60 min hour).

● Charts are for all classes of material.

● In igneous rock with seismic velocity of 8000 fps (2450 mps) or higher for the D11T, and 6000 fps (1830 mps) or higher for the D10T2, D9R/D9T and D8R/D8T, the production figures shown should be reduced by 25%.

● Upper limit of charts reflect ripping under ideal con-di tions only. If conditions such as thick lamination, vertical lamination or any factor which would adversely affect production are present, the lower limit should be used.

B

A

2 3 4 5 6 7 8

250

500

750

1000

1250

1500

1750

2000

2250

2500

2750

3000

3250

1 2

250

500

750

1000

1250

1500

1750

2000

2250

2500

B

2 3 4 5 6 7 8

250

500

750

1000

1250

1500

1750

2000

2250

2500

2750

3000

3250

250

500

750

1000

1250

1500

1750

2000

2250

2500

1 2

A

SEISMIC VELOCITY (in meters per second x 1000)

KEY

A — IDEALB — ADVERSE

SEISMIC VELOCITY (in feet per second x 1000)

D9R/D9T WITH SINGLE SHANK

PR

OD

UC

TIO

N (

BC

Y/h

ou

r)

PR

OD

UC

TIO

N (

Bm

3/h

ou

r)



D8R/D8T WITH SINGLE SHANK

PR

OD

UC

TIO

N (

BC

Y/h

ou

r)

PR

OD

UC

TIO

N (

Bm

3/h

ou

r)

19-82 Edition 47

Rippers Estimated Ripper Production Graphs● D10T2 ● D11T ● D11T CD

B

A

2 3 4 5 6 7 98

250

500

750

1000

1250

1500

1750

2000

2250

2500

2750

3000

3250

1 2

250

500

750

1000

1250

1500

1750

2000

2250

2500



D10T2 WITH SINGLE SHANK

PR

OD

UC

TIO

N (

BC

Y/h

ou

r)

PR

OD

UC

TIO

N (

Bm

3/h

ou

r)

A

B

2 3 6 7 1094 85

1000

2000

3000

4000

5000

1 2 3

750

1500

2250

3000

3750



D11T WITH SINGLE SHANK

PR

OD

UC

TIO

N (

BC

Y/h

ou

r)

PR

OD

UC

TIO

N (

Bm

3/h

ou

r)

KEY

A — IDEALB — ADVERSE

A

B

2 3 6 7 1094 85

1000

2000

3000

4000

5000

1 2 3

750

1500

2250

3000

3750



D11T CD WITH SINGLE SHANK

PR

OD

UC

TIO

N (

BC

Y/h

ou

r)

PR

OD

UC

TIO

N (

Bm

3/h

ou

r)

19

CONTENTS

PACCAR

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-84 Physical Specifications. . . . . . . . . . . . . . . . . . . .19-85 Operating Specifications . . . . . . . . . . . . . . . . . .19-95

Allied

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-99 Physical Specifications. . . . . . . . . . . . . . . . . . 19-100 Operating Specifications . . . . . . . . . . . . . . . . .19-107

WINCHESPACCAR

ALLIED

Edition 47 19-83

PACCAR Features:

PACCAR winches have been installed on Cat trac-tors since 1932. After acquiring the intellectual and property rights of Cat tail winches in the early 1990’s, PACCAR Winch has exclusively supplied Caterpillar man u fac tur ing facilities worldwide with tractor winches for factory installation.

PA40 and PA50

● Closed loop hydrostatic operation with variable displace-ment motor and dedicated variable displacement pump for maximum winching power and flexibility.

● Infinitely variable control of line speed and line pull including positive inching control at maximum rated line pull.

● Standard full-function “power-in” and “power-out” con trol. This is optional on some competitive winches.

● Standard “drive-away” to maintain tension on the cable when driving the tractor away from a stationary load.

● Standard “free spool” to allow cable to be pulled off the winch by hand.

● Durable cast winch case with fairlead mounting lugs, log arch mounting lugs, and heavy duty drawbar.

PA55, PA56 and PA80

● PTO mechanical winch drive with full tractor engine power available to the winch.

● Self-contained internal hydraulic control system for easy installation.

● Equal speed gearing in “reel-in” and “reel-out” to provide smooth and predictable performance.

● Standard “drive-away” to maintain tension on the cable when driving the tractor away from a stationary load.

● Standard “free spool” to allow cable to be pulled off the winch by hand.

● Durable cast winch case with fairlead mounting lugs, log arch mounting lugs, and heavy duty drawbar.

PA90, PA110B, PA140 and H200

● Hydraulically driven winch for infinitely variable con-trol of line speed and line pull including positive inch-ing control at maximum rated line pull.

● Optimized “high power” hydraulic control system including specialized directional control valve for maximum winching power and flexibility.

● Dual braking system provides a static brake with sprag clutch to eliminate fall-back and a hydraulic brake valve for dynamic braking.

● Single lever joystick control for ease of operation.

● Fabricated steel winch case with integral heavy duty draw bar provides excellent durability and easy weld-ability.

● Standard three-roller fairlead for improved wire rope life during side pulls.

H60, H110B and H140

● Hydraulically driven winch for infinitely variable con-trol of line speed and line pull including positive inch-ing control at maximum rated line pull.

● Standard Cat ripper control system is employed for winch “power-in” and “power-out” functions.

● Winch installation time is reduced by up to 70% com-pared to “high power” installations.

● Easy field interchangeability between winch and ripper.

● Dual braking system provides a static brake with sprag clutch to eliminate fall-back and a hydraulic brake valve for dynamic braking.

● Durable cast (H60) or fabricated steel (H110B and H140) winch case with integral heavy duty drawbar.

● Three-roller fairlead for improved wire rope life dur-ing side pulls is standard on H110B and H140 and optional on H60.

● “Free spool” to allow cable to be pulled off the winch by hand is standard on H60.

19-84 Edition 47

WinchesPACCAR

Features

19

Edition 47 19-85

WinchesPACCAR

Physical Specifications● PA40 ● PA50

WINCH MODEL PA40 PA50

TRACTOR MODEL D3K2, D4K2, D5K25 D3K2, D4K2, D5K2 D6K2Tractor transmission Hydrostatic Hydrostatic Hydrostatic

Winch drive Hydrostatic Hydrostatic Hydrostatic

A Tractor to rear of winch 751 mm 29.6" 751 mm 29.6" 845 mm 33.2"

B Tractor to drum centerline 521 mm 20.5" 521 mm 20.5" 615 mm 24.2"

C Ground to top of winch 1327 mm 52.2" 1327 mm 52.2" 1380 mm 54.4"

D Ground to drum centerline 959 mm 37.8" 959 mm 37.8" 1010 mm 39.8"

E Ground to center of hitch 473 mm 18.6" 473 mm 18.6" 525 mm 20.7"

F Tractor to drawbar pin centerline 410 mm 16.1" 410 mm 16.1" 505 mm 19.8"

Winch width (not shown)1 740 mm 29.2" 740 mm 29.2" 740 mm 29.2"

Drum diameter (not shown) 255 mm 10.0" 255 mm 10.0" 205 mm 8.0"

Weight2 610 kg 1345 lb 610 kg 1345 lb 610 kg 1345 lb

Oil refill capacity 4.3 L 4.5 qt 4.3 L 4.5 qt 4.3 L 4.5 qt

Wire rope diameter:

Recommended 16 mm 0.63" 16 mm 0.63" 19 mm 0.75"

Optional 19 mm 0.75" 19 mm 0.75" 22 mm 0.88"

Maximum theoretical

drum capacity:3

Recommended rope 114 m 374' 114 m 374' 93 m 306'

Optional rope 80 m 264' 80 m 264' 67 m 220'

Maximum recommended

drum capacity:4



Wire rope ferrule size (OD) 54 mm 2.13" 54 mm 2.13" 54 mm 2.13"

Wire rope ferrule size (length) 67 mm 2.63" 67 mm 2.63" 67 mm 2.63"1 Width does not include mounting brackets/adapters (if any).2 Weight shown is base winch only. Does not include mounting arrangement, control arrangement, oil, or wire rope.3 Per SAE J1158.4 Per SAE J706 (K=.9).5 Meets Tier 3/Stage IIIA/Japan 2006 (Tier 3) equivalent emission standards.

19-86 Edition 47

WinchesPACCAR

Physical Specifications● PA55

WINCH MODEL PA55

TRACTOR MODEL D5R XL, D6N XL D5R LGP, D6N LGPTractor transmission Powershift Powershift

Winch drive PTO PTO

A Tractor to rear of winch 1145 mm 45.1" 1145 mm 45.1"

B Tractor to drum centerline 890 mm 35.1" 890 mm 35.1"

C Ground to top of winch 1330 mm 52.3" 1380 mm 54.3"

D Ground to drum centerline 960 mm 37.8" 1010 mm 39.8"

E Ground to center of hitch 525 mm 20.7" 575 mm 22.7"

F Tractor to drawbar pin centerline 845 mm 33.2" 845 mm 33.2"

Winch width (not shown)1 975 mm 38.3" 975 mm 38.3"

Drum diameter (not shown) 255 mm 10.0" 255 mm 10.0"

Weight2 1180 kg 2600 lb 1180 kg 2600 lb

Oil refill capacity 74 L 19.5 U.S. gal 74 L 19.5 U.S. gal

Wire rope diameter:

Recommended 19 mm 0.75" 19 mm 0.75"

Optional 22 mm 0.88" 22 mm 0.88"

Maximum theoretical drum capacity:3

Recommended rope 119 m 391' 119 m 391'

Optional rope 85 m 281' 85 m 281'

Maximum recommended drum capacity:4



Wire rope ferrule size (OD) 54 mm 2.13" 54 mm 2.13"

Wire rope ferrule size (length) 67 mm 2.63" 67 mm 2.63"1 Width does not include mounting brackets/adapters (if any).2 Weight shown is base winch only. Does not include mounting arrangement, control arrangement, oil, or wire rope.3 Per SAE J1158.4 Per SAE J706 (K=.9).

Edition 47 19-87

19

Physical Specifications● H60

WinchesPACCAR

WINCH MODEL H60

TRACTOR MODEL D5R XL, D6N XL D5R LGP, D6N LGPTractor transmission Powershift Powershift

Winch drive Hydraulic (Ripper) Hydraulic (Ripper)









Weight2 1180 kg 2600 lb 1180 kg 2600 lb


Wire rope diameter:


Optional 26 mm 1.0" 26 mm 1.0"









19-88 Edition 47

WinchesPACCAR

Physical Specifications● PA56

WINCH MODEL PA56

TRACTOR MODEL

D6R, D6R XL, D6T, D6T5

XL, XL VPAT, XW

D6R LGP, D6T5

XW VPAT, LGP, and LGP VPATTractor transmission Powershift Powershift

Winch drive PTO PTO









Weight2 1180 kg 2600 lb 1180 kg 2600 lb


Wire rope diameter:










Wire rope ferrule size (length) 67 mm 2.63" 67 mm 2.63"1 Width does not include mounting brackets/adapters (if any).2 Weight shown is base winch only. Does not include mounting arrangement, control arrangement, oil, or wire rope.3 Per SAE J1158.4 Per SAE J706 (K=.9).5 Meets Tier 4 Final/Stage IV/Japan 2014 (Tier 4 Final) emission standards.

Edition 47 19-89

19

WinchesPACCAR


WINCH MODEL H85

TRACTOR MODEL D6T5

XL, XL VPAT, and XW

D6T5

XW VPAT, LGP, and LGP VPATTractor transmission Powershift Powershift

Winch drive Hydraulic (Ripper) Hydraulic (Ripper)









Weight2 1180 kg 2600 lb 1180 kg 2600 lb


Wire rope diameter:










Wire rope ferrule size (length) 67 mm 2.63" 67 mm 2.63"1 Width does not include mounting brackets/adapters (if any).2 Weight shown is base winch only. Does not include mounting arrangement, control arrangement, oil, or wire rope.3 Per SAE J1158.4 Per SAE J706 (K=.9).5 Meets Tier 4 Final/Stage IV/Japan 2014 (Tier 4 Final) emission standards.

19-90 Edition 47

Physical Specifications● PA90 ● H110B

WinchesPACCAR

WINCH MODEL PA90 H110B

TRACTOR MODEL D7E D7ETractor transmission Electric Electric

Winch drive Hydraulic Hydraulic

A Tractor to rear of winch 1265 mm 49.8" 1265 mm 4'8.5"

B Tractor to drum centerline 755 mm 29.7" 755 mm 3'0.4"

C Ground to top of winch 1665 mm 65.6" 1665 mm 5'6.8"

D Ground to drum centerline 1235 mm 48.5" 1235 mm 4'1.5"

E Ground to center of hitch 670 mm 26.3" 670 mm 2'3.8"

F Tractor to drawbar pin centerline 995 mm 39.2" 995 mm 4'0"

Winch width (not shown)1 1090 mm 43.0" 1160 mm 3'9.6"

Drum diameter (not shown) 320 mm 12.5" 320 mm 1'0.5"

Weight2 1520 kg 3350 lb 1790 kg 3950 lb

Oil refill capacity 12 L 12.5 qt 15 L 4 U.S. gal

Wire rope diameter:

Recommended 26 mm 1" 28 mm 1.13"

Optional 28 mm 1.13" 32 mm 1.25"









Edition 47 19-91

19

WinchesPACCAR

Physical Specifications● PA90 ● H110B

WINCH MODEL PA90 H110B

TRACTOR MODEL

D6R, D6T5

XW VPAT

D6T5

LGP and LGP VPAT D6TTractor transmission Powershift Powershift Powershift

Winch drive Hydraulic (High Power) Hydraulic (High Power) Hydraulic (High Power)

A Tractor to rear of winch 1380 mm 4'6" 1380 mm 4'6" 1380 mm 4'6"

B Tractor to drum centerline 870 mm 2'10" 870 mm 2'10" 870 mm 2'10"

C Ground to top of winch 1680 mm 5'6" 1730 mm 5'8" 1730 mm 5'8"

D Ground to drum centerline 1235 mm 4'1" 1285 mm 4'3" 1285 mm 4'3"

E Ground to center of hitch 670 mm 2'2" 720 mm 2'4" 720 mm 2'4"

F Tractor to drawbar pin centerline 1160 mm 3'8" 1160 mm 3'8" 1160 mm 3'8"

Winch width (not shown)1 1190 mm 3'7" 1190 mm 3'7" 1190 mm 3'7"

Drum diameter (not shown) 320 mm 1'1" 320 mm 1'1" 320 mm 1'1"

Weight2 1500 kg 3300 lb 1500 kg 3300 lb 1790 kg 3950 lb

Oil refill capacity 12 L 3.13 U.S. gal 12 L 3.13 U.S. gal 15 L 4 U.S. gal

Wire rope diameter:

Recommended 26 mm 1" 26 mm 1" 28 mm 1.13"

Optional 28 mm 1.13" 28 mm 1.13" 32 mm 1.25"







Wire rope ferrule size (OD) 60 mm 2.38" 60 mm 2.38" 60 mm 2.38"

Wire rope ferrule size (length) 70 mm 2.75" 70 mm 2.75" 70 mm 2.75"1 Width does not include mounting brackets/adapters (if any).2 Weight shown is base winch only. Does not include mounting arrangement, control arrangement, oil, or wire rope.3 Per SAE J1158.4 Per SAE J706 (K=.9).5 Meets Tier 3/Stage IIIA/Japan 2006 (Tier 3) equivalent emission standards.

19-92 Edition 47

WinchesPACCAR

Physical Specifications● H110B ● PA110B

WINCH MODEL H110B PA110B

TRACTOR MODEL D7R D7RTractor transmission Powershift Powershift

Winch drive Hydraulic (Ripper) Hydraulic (High Power)

A Tractor to rear of winch 1585 mm 5'2.4" 1435 mm 4'8.5"

B Tractor to drum centerline 1075 mm 3'6.3" 925 mm 3'0.4"

C Ground to top of winch 1695 mm 5'6.8" 1695 mm 5'6.8"

D Ground to drum centerline 1255 mm 4'1.5" 1255 mm 4'1.5"

E Ground to center of hitch 705 mm 2'3.8" 705 mm 2'3.8"

F Tractor to drawbar pin centerline 1370 mm 4'5.9" 1220 mm 4'0"

Winch width (not shown)1 1160 mm 3'9.6" 1160 mm 3'9.6"

Drum diameter (not shown) 320 mm 1'0.5" 320 mm 1'0.5"

Weight2 1790 kg 3950 lb 1790 kg 3950 lb

Oil refill capacity 15 L 4 U.S. gal 15 L 4 U.S. gal

Wire rope diameter:


Optional 32 mm 1.25" 32 mm 1.25"









19

Edition 47 19-93

WinchesPACCAR

Physical Specifications● H140 ● PA140

WINCH MODEL H140 PA140

TRACTOR MODEL D8R, D8T D9R, D9T D8R, D8T D9R, D9TTractor transmission Powershift Powershift Powershift Powershift

Winch drive Hydraulic (Ripper) Hydraulic (Ripper) Hydraulic (High Power) Hydraulic (High Power)

A Tractor to rear of winch 1585 mm 5'2.4" 1525 mm 5'0.3" 1435 mm 4'8.5" 1620 mm 5'3.8"

B Tractor to drum centerline 1075 mm 3'6.3" 1015 mm 3'4.0" 925 mm 3'0.4" 1110 mm 3'7.7"

C Ground to top of winch 1715 mm 5'7.5" 1740 mm 5'8.4" 1715 mm 5'7.5" 1740 mm 5'8.4"

D Ground to drum centerline 1275 mm 4'2.1" 1300 mm 4'3.2" 1275 mm 4'2.1" 1300 mm 4'3.2"

E Ground to center of hitch 725 mm 2'4.5" 750 mm 2'5.5" 725 mm 2'4.5" 750 mm 2'5.5"

F Tractor to drawbar pin

centerline 1370 mm 4'5.9" 1255 mm 4'1.5" 1220 mm 4'0" 1350 mm 4'5.2"

Winch width (not shown)1 1160 mm 3'9.6" 1160 mm 3'9.6" 1160 mm 3'9.6" 1160 mm 3'9.6"

Drum diameter (not shown) 320 mm 2'0.5" 320 mm 12.5" 320 mm 12.5" 320 mm 12.5"

Weight2 1790 kg 3950 lb 1790 kg 3950 lb 1790 kg 3950 lb 1790 kg5 3950 lb5

Oil refill capacity 15 L 4 U.S. gal 15 L 4 U.S. gal 15 L 4 U.S. gal 15 L 4 U.S. gal

Wire rope diameter:

Recommended 28 mm 1.13" 28 mm 1.13" 28 mm 1.13" 28 mm 1.13"

Optional 32 mm 1.25" 32 mm 1.25" 32 mm 1.25" 32 mm 1.25"

Maximum theoretical

drum capacity:3

Recommended rope 78 m 257' 78 m 257' 78 m 257' 78 m 257'

Optional rope 62 m 204' 62 m 204' 62 m 204' 62 m 204'

Maximum recommended

drum capacity:4

Recommended rope 55 m 182' 55 m 182' 55 m 182' 55 m 182'

Optional rope 36 m 118' 36 m 118' 36 m 118' 36 m 118'

Wire rope ferrule size (OD) 60 mm 2.38" 60 mm 2.38" 60 mm 2.38" 60 mm 2.38"

Wire rope ferrule size (length) 70 mm 2.75" 70 mm 2.75" 70 mm 2.75" 70 mm 2.75"1 Width does not include mounting brackets/adapters (if any).2 Weight shown is base winch only. Does not include mounting arrangement, control arrangement, oil, or wire rope.3 Per SAE J1158.4 Per SAE J706 (K=.9).5 3700 kg (8150 lb) with counterweight.

19-94 Edition 47


WinchesPACCAR

WINCH MODEL H200

TRACTOR MODEL D8T D9TTractor transmission Powershift Powershift

Winch drive Hydraulic (High Power) Hydraulic (High Power)






F Tractor to drawbar pin

centerline 1170 mm 46.1" 1305 mm 51.3"

Winch width (not shown)1 1400 mm 55" 1400 mm 55"

Drum diameter (not shown) 380 mm 15" 380 mm 15"

Weight2 3180 kg 7015 lb 3180 kg5 7015 lb5

Oil refill capacity 16.5 L 4.4 U.S. gal 16.5 L 4.4 U.S. gal

Wire rope diameter:



Maximum theoretical drum

capacity:3



Maximum recommended drum

capacity:4




Wire rope ferrule size (length) 79 mm 3.12" 79 mm 3.12"1 Width does not include mounting brackets/adapters (if any).2 Weight shown is base winch only. Does not include mounting arrangement, control arrangement, oil, or wire rope.3 Per SAE J1158.4 Per SAE J706 (K=.9).5 5080 kg (11,200 lb) with counterweight.

Edition 47 19-95

19

WinchesPACCAR

Operating Specifications● British Units of Measure● Metric Units of Measure

WINCH MODEL H110B PA90

TRACTOR MODEL D6T(5) D6R D6T D7ETractor transmission. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Powershift Powershift Powershift Electric

Winch drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic

(Ripper)

Hydraulic

(High Power)

Hydraulic

(High Power)

Hydraulic

(High Power)

British Units of Measure

Bare Drum

Maximum line pull(1) . . . . . . . . . . . . . . . . . lb 110,000 90,000 90,000 90,000

Rated line speed(2) . . . . . . . . . . . . . . . . . fpm 20 54 35 32

Maximum line speed(3) . . . . . . . . . . . . . fpm 38 87 68 71

Full Drum(4)




Metric Units of Measure

Bare Drum

Maximum line pull(1) . . . . . . . . . . . . . . . . kN 490.3 400.3 400.3 400.3

Rated line speed(2) . . . . . . . . . . . . . . . m/min 6 16 10 10

Maximum line speed(3) . . . . . . . . . . . m/min 12 26 20 22

Full Drum(4)



Maximum line speed(3) . . . . . . . . . . . m/min 19 42 34 37 (1)“Maximum line pull” is lesser of winch catalog rating or calculated maximum line pull at maximum tractor hydraulic system pressure.(2)“Rated line speed” is calculated maximum line speed at maximum line pull.(3)“Maximum line speed” is calculated maximum no-load line speed at maximum tractor hydraulic system flow.(4)“Full Drum” as defined by SAE J1158.(5)Meets Tier 4 Interim/Stage IIIB/Japan 2011 (Tier 4 Interim) equivalent emission standards.

WINCH MODEL PA40 PA50 H60 H85

TRACTOR MODEL

D3K2, D4K2,

D5K2(5) D6K2 D5R, D6N D6T(6)

Tractor transmission. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydrostatic Hydrostatic Powershift Powershift

Winch drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydrostatic Hydrostatic Hydraulic

(Ripper)

Hydraulic

(Ripper)


Bare Drum




Full Drum(4)





Bare Drum




Full Drum(4)



Maximum line speed(3) . . . . . . . . . . . m/min 63 70 52 28 (1)“Maximum line pull” is lesser of winch catalog rating or calculated maximum line pull at maximum tractor hydraulic system pressure.(2)“Rated line speed” is calculated maximum line speed at maximum line pull.(3)“Maximum line speed” is calculated maximum no-load line speed at maximum tractor hydraulic system flow.(4)“Full Drum” as defined by SAE J1158.(5)Meets Tier 3/Stage IIIA/Japan 2006 (Tier 3) equivalent emission standards.(6)Meets Tier 4 Final/Stage IV/Japan 2014 (Tier 4 Final) emission standards.

19-96 Edition 47

WinchesPACCAR


WINCH MODEL H140 PA140

TRACTOR MODEL D8R, D8T D9R, D9T D8T D9TTractor transmission. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Powershift Powershift Powershift Powershift

Winch drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic

(Ripper)

Hydraulic

(Ripper)

Hydraulic

(High Power)

Hydraulic

(High Power)


Bare Drum




Full Drum(4)





Bare Drum




Full Drum(4)



Maximum line speed(3) . . . . . . . . . . . m/min 19 17 23 23 (1)“Maximum line pull” is lesser of winch catalog rating or calculated maximum line pull at maximum tractor hydraulic system pressure.(2)“Rated line speed” is calculated maximum line speed at maximum line pull.(3)“Maximum line speed” is calculated maximum no-load line speed at maximum tractor hydraulic system flow.(4)“Full Drum” as defined by SAE J1158.

WINCH MODEL H110B H110B PA110B

TRACTOR MODEL D7E D7R D7RTractor transmission. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electric Powershift Powershift

Winch drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic (Ripper) Hydraulic (Ripper) Hydraulic (High Power)


Bare Drum

Maximum line pull(1) . . . . . . . . . . . . . . . . . lb 110,000 101,000 110,000

Rated line speed(2) . . . . . . . . . . . . . . . . . fpm 23 24 33

Maximum line speed(3) . . . . . . . . . . . . . fpm 55 51 100

Full Drum(4)

Maximum line pull(1) . . . . . . . . . . . . . . . . . lb 66,200 61,000 66,500

Rated line speed(2) . . . . . . . . . . . . . . . . . fpm 38 39 54

Maximum line speed(3) . . . . . . . . . . . . . fpm 90 84 165


Bare Drum

Maximum line pull(1) . . . . . . . . . . . . . . . . kN 490.3 449.3 489.3

Rated line speed(2) . . . . . . . . . . . . . . . m/min 7 7 10

Maximum line speed(3) . . . . . . . . . . . m/min 17 15 30

Full Drum(4)

Maximum line pull(1) . . . . . . . . . . . . . . . . kN 295.2 271.3 295.8

Rated line speed(2) . . . . . . . . . . . . . . . m/min 12 12 16

Maximum line speed(3) . . . . . . . . . . . m/min 27 25 50 (1)“Maximum line pull” is lesser of winch catalog rating or calculated maximum line pull at maximum tractor hydraulic system pressure.(2)“Rated line speed” is calculated maximum line speed at maximum line pull.(3)“Maximum line speed” is calculated maximum no-load line speed at maximum tractor hydraulic system flow.(4)“Full Drum” as defined by SAE J1158.

19

Edition 47 19-97

WinchesPACCAR


WINCH MODEL PA55 PA56

TRACTOR MODEL D5R, D6N D6R, D6T, D6T(6)

Tractor transmission. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Powershift Powershift

Winch drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PTO PTO


Bare Drum

Rated line pull(1) . . . . . . . . . . . . . . . . . . . . . lb 36,600 59,100

Maximum line pull(2) . . . . . . . . . . . . . . . . . lb 69,200 89,800

Rated line speed(3) . . . . . . . . . . . . . . . . . fpm 92 80

Maximum line speed(4) . . . . . . . . . . . . . fpm 141 130

Full Drum(5)





Slow speed gearing

Bare Drum





Full Drum(5)






Bare Drum

Rated line pull(1) . . . . . . . . . . . . . . . . . . . . kN 162.8 262.9

Maximum line pull(2) . . . . . . . . . . . . . . . . kN 307.8 399.5

Rated line speed(3) . . . . . . . . . . . . . . . m/min 28 24

Maximum line speed(4) . . . . . . . . . . . m/min 43 40

Full Drum(5)





Slow speed gearing

Bare Drum





Full Drum(5)




Maximum line speed(4) . . . . . . . . . . . m/min 28 31(1)“Rated line pull” is lesser of winch catalog rating or calculated line pull at maximum tractor PTO output power.(2)“ Maximum line pull” is lesser of calculated line pull at maximum tractor PTO output torque or catalog breaking strength of maximum optional size new

IWRC IPS wire rope.(3)“Rated line speed” is calculated line speed at maximum tractor PTO output power.(4)“Maximum line speed” is calculated no-load line speed at maximum tractor engine PTO output speed.(5)“Full Drum” as defined by SAE J1158.(6)Meets Tier 4 Final/Stage IV/Japan 2014 (Tier 4 Final) emission standards.

19-98 Edition 47

WINCH MODEL H200

TRACTOR MODEL D8T D9TTractor transmission. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Powershift Powershift

Winch drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic (High Power) Hydraulic (High Power)


Bare Drum




Full Drum(4)





Bare Drum




Full Drum(4)



Maximum line speed(3) . . . . . . . . . . . m/min 18 18 (1)“Maximum line pull” is lesser of winch catalog rating or calculated maximum line pull at maximum hydraulic system pressure.(2)“Rated line speed” is calculated maximum line speed at maximum hydraulic system pressure and flow with winch motor at maximum displacement.(3)“Maximum line speed” is calculated maximum no-load line speed at maximum hydraulic system flow with winch motor at minimum displacement.(4)“Full Drum” as defined by SAE J1158.


WinchesPACCAR

Edition 47 19-99

Winches19

Allied Features:

● Proven performance on Caterpillar. Allied winches trace their roots to Hyster winches on Cat tractors since 1929. Allied acquired Hyster winches in 1990, main-taining the same engineering excellence. Exist ing dealer parts inventory continues to be inter change able to support the thousands of Allied/Hyster winches in the field.

● “Plug and Play” design. Winches come complete with all the necessary parts for simple and easy field instal-la tion on any tractor. They do not require Winch Ready packages pre-ordered on the tractors. This sim plifies dealer inventory planning.

● Self-Contained Hydraulics (SCH) design. All hoses, pump and valve are inside the PTO winch frame, totally eliminating external leakage.

Standard Equipment

● Freespool function for W3C, H4A, W5C, H5C, W6F, W6G and H6H winches. Adjustable freespool drag to allow cable to be pulled out easily by hand.

● Heavy duty box-section winch frame withstands demand ing side pulls without the need for fairlead.

● Brake off function for most winches. Keeps cable tight while the tractor drives away to prevent cable bird nesting.

● Multiple-disc oil clutches and brake on PTO winches are oil-cooled for long life.

● Drawbar for most winches. Provides an additional hitch for load towing.

● Power line-in and power line-out.

Optional Equipment

● Fairlead to handle frequent side pulls from all angles. Hardened vertical and horizontal rollers reduce cable wear.

● Arch works like a raised fairlead to lift loads off ground for efficient skidding.

● Choice of standard gear ratio for fast operation in log ging, or slow speed gear ratio for fine speed con-trol in pipelaying and power line sagging applications.

● Electronic control for precise speed control.

Two families of winches – Power Take-Off (PTO) driven or Hydraulically driven winches covering D3 through D10 tractors, pipelayers and track loaders, the most com pre hen-sive winch in the industry.

● PTO winches able to utilize full range of engine power. Brute force and fast line speeds.

● Hydraulic winches provide fingertip precision control over line speed. Motor only turns on demand equal-ing less wear and maintenance.

Winch Selection Guide:

Tractor Class*

PTOWinch

HydraulicWinch

D3-5K — H4A

D6K — H5C

527 TSK W6F —

D6N, D5R W5C, W6G, W6F H5C, H6H

D6T, D6R W6G, W6F H6H

D7R W8L H8L

D7E — H8L

D8-9-10R, D8-9-10T W12E H12E

* For non-current tractors contact Allied Systems Company for winch options.

Features WinchesAllied

19-100 Edition 47

WinchesAllied

Physical Specifications● H4AT ● H4AH Hi-P

TRACTORREAR FACE

WINCH MODEL H4AT H4AH Hi-P

TRACTOR MODEL D3K2, D4K2, D5K2* D3K2, D4K2, D5K2*Winch drive Ripper Hydraulics Allied Hi-Flow Pump

Winch type Standard Hi-Performance

A Tractor to rear of winch 813 mm 32" 813 mm 32"

B Tractor to drum centerline 610 mm 24" 610 mm 24"

C Ground to top of winch 1143 mm 45" 1143 mm 45"

D Ground to drum centerline 889 mm 35" 889 mm 35"

E Ground to center of hitch 508 mm 20" 508 mm 20"

F Tractor to pin centerline 584 mm 23" 584 mm 23"

Overall width (not shown) 737 mm 29" 737 mm 29"


Weight 771 kg 1700 lb 812 kg 1790 lb


Wire rope diameter:


Optional 19 mm 0.75" 19 mm 0.75"

Drum capacity:




Wire rope ferrule size (length) 51 mm 2" 51 mm 2"

*Specifications based on representative models marked *. Others similar.

Edition 47 19-101

19

WinchesAllied

Physical Specifications● H5CT ● H5CH Hi-P

TRACTORREAR FACE

WINCH MODEL H5CT H5CH Hi-P

TRACTOR MODEL D6K2 D6K2Winch drive Ripper Hydraulics Allied Hi-Flow Pump

Winch type Standard Hi-Performance









Weight 898 kg 1980 lb 930 kg 2050 lb

Oil refill capacity 12.5 L 3.3 U.S. gal 12.5 L 3.3 U.S. gal

Wire rope diameter:


Optional 22 mm 0.88" 22 mm 0.88"

Drum capacity:



Wire rope ferrule size (OD) 51 mm 2" 51 mm 2"

Wire rope ferrule size (length) 57 mm 2.25" 57 mm 2.25"

19-102 Edition 47

WinchesAllied

Physical Specifications● H6H ● H8L

TRACTORREAR FACE

WINCH MODEL H6H H8L

TRACTOR MODEL D6N, D6R, D6R XL, D6T* D7E*, D7RWinch drive Ripper Hydraulics Hydraulic

Winch type Standard Standard









Weight 1284 kg 2830 lb 1542 kg 3400 lb

Oil refill capacity 8 L 2.1 U.S. gal 15 L 4 U.S. gal

Wire rope diameter:

Recommended 22 mm 0.88" 25 mm 1"

Optional 25 mm 1" 29 mm 1.12"

Drum capacity:



Wire rope ferrule size (OD) 51 mm 2" 57 mm 2.25"



TRACTORREAR FACE

H6H H8L

19

Edition 47 19-103

WinchesAllied

Physical Specifications● H12E

WINCH MODEL H12E

TRACTOR MODEL D8T*, D9T, D10T2Winch drive Hydraulic

Winch type Standard

A Tractor to rear of winch 1499 mm 59"

B Tractor to drum centerline 1168 mm 46"

C Ground to top of winch 1778 mm 70"

D Ground to drum centerline 1372 mm 54"

E Ground to center of hitch 711 mm 28"

F Tractor to pin centerline 1295 mm 51"

Overall width (not shown) 1245 mm 49"

Drum diameter (not shown) 356 mm 14"

Weight 2087 kg 4600 lb

Oil refill capacity 26.5 L 7 U.S. gal

Wire rope diameter:

Recommended 29 mm 1.13"

Optional 32 mm 1.25"

Drum capacity:

Recommended rope 70 m 229'

Optional rope 55 m 182'

Wire rope ferrule size (OD) 57 mm 2.25"

Wire rope ferrule size (length) 60 mm 2.38"


TRACTORREAR FACE

19-104 Edition 47

WinchesAllied

Physical Specifications● W6G ● W6F

TRACTORREAR FACE

WINCH MODEL W6G* W6F*

TRACTOR MODEL D5R2 527 D6R2Winch drive PTO PTO PTO

Winch type Standard Standard Standard

A Tractor to rear of winch 1041 mm 3'5" 1041 mm 3'5" 1244 mm 4'1"

B Tractor to drum centerline 737 mm 2'5" 762 mm 2'6" 965 mm 3'2"

C Ground to top of winch 1549 mm 5'1" 1549 mm 5'1" 1549 mm 5'1"

D Ground to drum centerline 1193 mm 3'11" 1193 mm 3'11" 1193 mm 3'11"

E Ground to center of hitch 711 mm 2'4" 711 mm 2'4" 711 mm 2'4"

F Tractor to pin centerline 737 mm 2'5" 737 mm 2'5" 737 mm 2'5"

Overall width (not shown) 1000 mm 3'4" 965 mm 3'2" 965 mm 3'2"

Drum diameter (not shown) 254 mm 10" 254 mm 10" 254 mm 10"


Oil refill capacity 62.5 L 16.5 U.S. gal 72 L 19 U.S. gal 72 L 19 U.S. gal

Wire rope diameter:

Recommended 22 mm 0.88" 22 mm 0.88" 22 mm 0.88"

Optional 25 mm 1" 25 mm 1" 25 mm 1"

Drum capacity:

Recommended rope 82.6 m 271' 87 m 287' 87 m 287'


Wire rope ferrule size (OD) 51 mm 2" 51 mm 2" 51 mm 2"

Wire rope ferrule size (length) 57 mm 2.25" 57 mm 2.25" 57 mm 2.25"

*W6F winch is configured for forestry applications, W6G for all other applications.

19

WINCH MODEL W6G W8L

TRACTOR MODEL D6R, D6RXL, D6T* D6N D7RWinch drive PTO PTO PTO

Winch type Standard Standard Standard

A Tractor to rear of winch 1245 mm 49" 1245 mm 49" 1245 mm 49"

B Tractor to drum centerline 965 mm 38" 965 mm 38" 965 mm 38"

C Ground to top of winch 1549 mm 61" 1549 mm 61" 1600 mm 63"

D Ground to drum centerline 1194 mm 47" 1194 mm 47" 1219 mm 48"

E Ground to center of hitch 711 mm 28" 711 mm 28" 610 mm 24"

F Tractor to pin centerline 940 mm 37" 940 mm 37" 1067 mm 42"

Overall width (not shown) 965 mm 38" 965 mm 38" 1041 mm 41"

Drum diameter (not shown) 254 mm 10" 254 mm 10" 305 mm 12"


Oil refill capacity 72 L 19 U.S. gal 72 L 19 U.S. gal 72 L 19 U.S. gal

Wire rope diameter:

Recommended 22 mm 0.88" 22 mm 0.88" 25 mm 1"

Optional 25 mm 1" 25 mm 1" 29 mm 1.13"

Drum capacity:



Wire rope ferrule size (OD) 51 mm 2" 51 mm 2" 57 mm 2.25"

Wire rope ferrule size (length) 57 mm 2.25" 57 mm 2.25" 60 mm 2.38"


Edition 47 19-105

WinchesAllied

Physical Specifications● W6G ● W8L

TRACTORREAR FACE

19-106 Edition 47

WinchesAllied

Physical Specifications● W12E

WINCH MODEL W12E

TRACTOR MODEL D8T*, D9R, D9T, PL83, PL87 D10T2Winch drive PTO PTO

Winch type Standard Standard









Weight 2880 kg 6350 lb 4105 kg 9050 lb


Wire rope diameter:


Optional 32 mm 1.25" 32 mm 1.25"

Drum capacity:






TRACTORREAR FACE

19

Edition 47 19-107

WinchesAllied


WINCH MODEL H4AT H4AH

TRACTOR MODEL D3K2, D4K2, D5K2* D3K2, D4K2, D5K2*Winch drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ripper Hydraulics Allied Hi-Flow Pump

Winch type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard Hi-Performance


Bare Drum

Maximum line pull** . . . . . . . . . . . . . . . . lb 32,150 38,600

Line speed at . . . . . . . . . . . . . . . . . . . . . fpm 34 94

Typical line pull of . . . . . . . . . . . . . . . . . . . lb 20,000 20,000

Maximum line speed . . . . . . . . . . . . . . fpm 46 100

Full Drum

Maximum line pull** . . . . . . . . . . . . . . . . lb 18,350 22,050

Line speed at . . . . . . . . . . . . . . . . . . . . . fpm 48 98




Bare Drum

Maximum line pull** . . . . . . . . . . . . . . . kg 14 583 17 509

Line speed at . . . . . . . . . . . . . . . . . . . m/min 10.4 28.7

Typical line pull of . . . . . . . . . . . . . . . . . . kg 9072 9072

Maximum line speed . . . . . . . . . . . . m/min 14 31.5

Full Drum

Maximum line pull** . . . . . . . . . . . . . . . kg 8323 10 002


Typical line pull of . . . . . . . . . . . . . . . . . . kg 7893 9072

Maximum line speed . . . . . . . . . . . . m/min 25 54

Performance based on standard gear ratio. Optional gear ratios available for different line speed and line pull requirements. *Specifications based on representative models marked *. Others similar.** Based on lower measurement of maximum line pull that the tractor can develop with the standard gear ratio, or the breaking strength of the maximum

recommended wire.

19-108 Edition 47

WINCH MODEL H5CT H5CH

TRACTOR MODEL D6K2 D6K2Winch drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ripper Hydraulics Allied Hi-Flow Pump

Winch type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard Hi-Performance


Bare Drum

Maximum line pull* . . . . . . . . . . . . . . . . . lb 66,700 59,750

Line speed at . . . . . . . . . . . . . . . . . . . . . fpm 25 97



Full Drum

Maximum line pull* . . . . . . . . . . . . . . . . . lb 35,950 32,200

Line speed at . . . . . . . . . . . . . . . . . . . . . fpm 47 70




Bare Drum

Maximum line pull* . . . . . . . . . . . . . . . . kg 30 255 27 102


Typical line pull of . . . . . . . . . . . . . . . . . . kg 13 608 13 608


Full Drum

Maximum line pull* . . . . . . . . . . . . . . . . kg 16 307 14 606


Typical line pull of . . . . . . . . . . . . . . . . . . kg 13 608 13 608


Performance based on standard gear ratio. Optional gear ratios available for different line speed and line pull requirements.* Based on lower measurement of maximum line pull that the tractor can develop with the standard gear ratio, or the breaking strength of the maximum

recommended wire.

WinchesAllied


Edition 47 19-109

19

WINCH MODEL H6H H8L H12E

TRACTOR MODEL D6T*, D6R, D6N D7E D8T*, D9T, D10T2Winch drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ripper Hydraulics Hydraulic Hydraulic

Winch type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard Standard Standard


Bare Drum

Maximum line pull** . . . . . . . . . . . . . . lb 88,800 112,500 130,250

Line speed at . . . . . . . . . . . . . . . . . . . .fpm 58 29 22

Typical line pull of . . . . . . . . . . . . . . . . . lb 40,000 50,000 80,000

Maximum line speed . . . . . . . . . . . . .fpm 69 65 76

Full Drum


Line speed at . . . . . . . . . . . . . . . . . . . .fpm 60 47 35




Bare Drum

Maximum line pull** . . . . . . . . . . . . . . kg 40 280 52 029 59 080

Line speed at . . . . . . . . . . . . . . . . . m/min 18.0 8.8 7.0

Typical line pull of . . . . . . . . . . . . . . . . . kg 18 144 22 700 36 287

Maximum line speed . . . . . . . . . . m/min 21.0 19.8 23.2

Full Drum




Maximum line speed . . . . . . . . . . m/min 39.0 32.3 36.3


recommended wire.

WinchesAllied


19-110 Edition 47

WinchesAllied


WINCH MODEL W6F W6G

TRACTOR MODEL 527 D5R2 D6T*, D6R2Winch drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PTO PTO PTO

Winch type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard Standard Standard


Bare Drum


Line speed at . . . . . . . . . . . . . . . . . . . .fpm 93 59 93



Full Drum


Line speed at . . . . . . . . . . . . . . . . . . . .fpm 99 90 99




Bare Drum




Maximum line speed . . . . . . . . . . m/min 37 21 37

Full Drum




Maximum line speed . . . . . . . . . . m/min 67 38 67


recommended wire.

19

Edition 47 19-111

WinchesAllied


WINCH MODEL W8L W12E

TRACTOR MODEL

D7R*,

572R

D8T*,

PL83, PL87 D9T D10TWinch drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PTO PTO PTO PTO

Winch type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard Standard Standard Standard


Bare Drum

Maximum line pull** . . . . . . . . . . . . . . lb 112,500 138,800 138,800 138,800

Line speed at . . . . . . . . . . . . . . . . . . . .fpm 122 52 55 53

Typical line pull of . . . . . . . . . . . . . . . . . lb 50,000 80,000 80,000 80,000

Maximum line speed . . . . . . . . . . . . .fpm 168 59 60 58

Full Drum

Maximum line pull** . . . . . . . . . . . . . . lb 81,700 138,800 138,800 138,800

Line speed at . . . . . . . . . . . . . . . . . . . .fpm 115 78 82 81

Typical line pull of . . . . . . . . . . . . . . . . . lb 50,000 80,000 80,000 80,000

Maximum line speed . . . . . . . . . . . . .fpm 275 92 93 91


Bare Drum

Maximum line pull** . . . . . . . . . . . . . . kg 51 030 62 960 62 960 62 960

Line speed at . . . . . . . . . . . . . . . . . m/min 37.2 15.8 16.8 16.2

Typical line pull of . . . . . . . . . . . . . . . . . kg 22 700 36 287 36 287 36 287

Maximum line speed . . . . . . . . . . m/min 51.2 18.0 18.3 17.7

Full Drum

Maximum line pull** . . . . . . . . . . . . . . kg 37 058 62 959 62 959 62 959

Line speed at . . . . . . . . . . . . . . . . . m/min 35.1 23.8 25.0 24.7

Typical line pull of . . . . . . . . . . . . . . . . . kg 22 700 36 287 36 287 36 287

Maximum line speed . . . . . . . . . . m/min 83.8 28.0 28.3 27.7


recommended wire.

19-112 Edition 47

Notes —

19 Hydraulic Controls Bulldozers Rippers and Winches · 2018-03-21 · Track-Type Tractors Features...

Documents

Transcript of 19 Hydraulic Controls Bulldozers Rippers and Winches · 2018-03-21 · Track-Type Tractors Features...