160926 TL-DA14-HD2 Manual - Future Ready Solutions · The TL-DA14-HD2 is a 1x4 splitter featuring...

User Manual TL-DA14-HD2

1x4 HDMI Splitter & Distribution Amplifier

All Rights Reserved Version: TL-DA14-HD2_160926

TL-DA14-HD2 User Manual

www.tlnetworx.com

Preface Read this user manual carefully before using this product. Pictures shown in this manual are for reference only; the actual product may vary.

This manual is only for operation instruction only and not for any maintenance or repair.

Trademarks Product model and logo are trademarked. Any other trademarks mentioned in this manual are acknowledged as the properties of the trademark owner. No part of this publication may be copied or reproduced without prior written consent.

FCC Statement This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation.

Operation of this equipment in a residential area is likely to cause interference, in which case the user at their own expense will be required to take whatever measures may be necessary to correct the interference.

Any changes or modifications not expressly approved by the manufacture would void the user’s authority to operate the equipment.


www.tlnetworx.com

SAFETY PRECAUTIONS To insure proper operation, please read all instructions carefully before using the device. Save this manual for further reference.

l Unpack the equipment carefully and save the original box and packing material for possible future shipment

l Follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.

l Do not dismantle the housing or modify the module. It may result in electrical shock or burn.

l Using supplies or parts not meeting the products’ specifications may cause damage, deterioration or malfunction.

l Refer all servicing to qualified service personnel.

l To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.

l Do not remove the housing of the device, as opening or removing housing may expose you to dangerous voltage or other hazards.

l Install the device in a place with adequate ventilation to avoid damage caused by overheating.

l Keep the device away from liquids.

l Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on to the housing, unplug the device immediately.

l Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.

l Unplug the power cord when left unused for a long period of time.

l If disposing of the unit, do not burn or mix with general household waste. The device must be disposed of per local regulations for electronic recycling.


Contents

1. Introduction ................................................................................................................. 5

1.1 Introduction to TL-DA14-HD2 ............................................................................ 5

1.2 Features .............................................................................................................. 5

1.3 Package List ........................................................................................................ 5

2. Panel Description ......................................................................................................... 6

2.1 Front Panel ......................................................................................................... 6

2.2 Rear Panel ........................................................... Error! Bookmark not defined.

3. System Connection ...................................................................................................... 8

3.1 Usage Precautions .............................................................................................. 8

3.2 System Diagram .................................................................................................. 8

3.3 Connection Procedures ...................................................................................... 8

3.4 EDID Management ............................................................................................. 8

4. Specification .............................................................................................................. 10

4.1 Supported Input Video Formats ........................................................................ 11

5. Panel Drawing .............................................................................................................. 1

6. Troubleshooting & Maintenance .................................................................................. 2

7. After-sales Service ....................................................................................................... 3


1. Introduction 1.1 Introduction to TL-DA14-HD2 The TL-DA14-HD2 is a 1x4 splitter featuring the capability to repeat HDMI or DVI source to two displays simultaneously. Compliant with HDMI 2.0 and HDCP 2.2, the TL-DA14-HD2 provides comprehensive resolution capacities up to 4K@60 4:4:4 and 1080p with 3D. It’s capable of automatically recognizing the resolution and HDCP status of the input signal, and the HDMI signal is automatically equalized for reliable transmission with proper EDID management.

Moreover, TL-DA14-HD2 supports convenient online update through USB port.

1.2 Features l Four simultaneous HDMI outputs

l Supports hot-plug

l HDMI 2.0 compliant, capable of transmitting 1080p 3D & 4K@60 4:4:4 signals

l Transmits 1080p HDMI up to 15m

l 18 Gbps bandwidth

l HDCP compliant

l Automatically identifies input resolution

l Supports EDID management, automatically adopts the resolution of the first detected display from ports 1 - 4

l Intuitive indicators for connection status & input HDCP encryption status

l Convenient online firmware update

1.3 Package List l 1 x Splitter

l 2 x Mounting ears

l 4 x Screws

l 4 x Plastic cushions

l 1 x Power Adapter (DC 5V A)

l 1 x User Manual


2. Panel Description 2.1 Front Panel

No. Name Description

① Power indicator Illuminates red when properly powered on

② Input HDCP compliant Indicator

Indicates the HDCP encryption status of the input signal

Ø Iluminates green when the input signal is HDCP encrypted

Ø Blinks green when the input signal is not HDCP encrypted

Ø Remains off when there is no input signal

③ Output signal Indicators

Illuminates green when there is an HDMI output; corresponds to HDMI OUTPUT 1 - 4 separately

④ DC 5V

Micro USB port; connect a DC 5V power adapter for power or plug a USB drive for firmware updates

Note: Firmware updates require auxiliary equipment; please contact TechLogix for additional details.

⑤ OUT 1~ OUT 4

HDMI output ports. Connects to HDMI displays, automatically capturing the input resolution.

⑥ IN HDMI input port. Connects with an HDMI or DVI source device such as a DVD player or set top box.

Note: Output HDCP compliancy status depends on the input signal. When the input signal is HDCP compliant, then output signal will be HDCP compliant and vice versa.

1IN 1 2 3 4

321 OUT 2

OUT 1

IN

OUT 3

OUT 4DC 5V

4 5 6


Note:

a) Pictures shown in this manual are for reference only.

b) The HDMI signal contains both a video signal and embedded audio signal (PCM, Dolby Digital, DTS, DTS-HD), whereas a DVI signal contains solely a video signal.

c) The splitter is capable of switching input signal formats according to the displays.

For example, when the input signal is HDMI and the display can only support DVI signal, the unit will switch the signal into DVI format.

d) EDID management automatically manages the output signal (e.g. output resolution) to fit all displays.


3. System Connection 3.1 Usage Precautions 1) System should be installed in a clean environment that has a proper temperature and

humidity. 2) All of the power switches, plugs, sockets and power cords should be installed

properly. 3) All devices should be connected before powering on the devices.

3.2 System Diagram The following diagram illustrates typical input and output connections that can be utilized with TL-DA14-HD2:

3.3 Connection Procedures Step1. Connect an HDMI or DVI source device (e.g. DVD) to the HDMI INPUT socket of

the TL-DA14-HD2 using a high-quality HDMI cable.

Step2. Connect HDMI displays to the HDMI OUTPUT sockets of TL-DA14-HD2 with high-quality HDMI cables.

Step3. Connect the DC 5V power adapter to the power port of TL-DA14-HD2.

Note: All the ports support hot-plug. Please note that hot plugging a display may result in screen splashing at the output ends.

OUT 2

OUT 1

IN

OUT 3

OUT 4DC 5V


3.4 EDID Management TL-DA14-HD2 comprises of one HDMI input port and four HDMI output ports. EDID management helps distribute and route signals from the source at the resolution of the first detected display (detecting from output 1 - 4).

For example: when output 1 connects with a 1080p display, the TL-DA14-HD2 will select 1080p as output resolution and distribute 1080p signal to displays connected to output 1 - 4.

Note: If the displays connected to outputs 2 - 4 don’t support a 1080p signal, the display will not show a signal.


4. Specification I/O Connections

HDMI Input One (1) HDMI Type A receptacle

HDMI Outputs Four (4) HDMI Type A receptacle

Power DC 5V 2A

Supported Video and Audio

Resolutions 480i, 480p, 576i, 576p, 720p, 1080i, 1080p,

1080p 3D, 4Kx2K (24, 25, 30, 60 Hz)

Video Compliance HDMI 2.0, HDCP 2.2, DVI 1.0

Bandwidth 18 Gbps

Embedded Audio Compatibility Up to PCM 5 channel, Dolby Digital TrueHD,

and DTS-HD Master Audio

Maximum Passive HDMI Distance 10m (33 ft)

Input DDC Signal 5.0 volts p-p (TTL)

Input Video Signal 0.5 ~ 1.0 volts p-p

Chassis and Environmental

Enclosure Painted aluminum

Dimensions (W x H x D) 152.4mm x 11mm x 70.4mm (6.00in x 0.43in x

2.77in)

Shipping Weight 0.46Kg(1.00bls)

Operating Temperature

(Environment) -10° ~ +40° C (+14° ~ +104° F)

Operating Temperature (Chassis) 45° C(113° F)

Operating Humidity (Environment) 10% ~ 90% Non-condensing

Storage Temperature

(Environment) -15° ~ +70° C(+5° ~ +167° F)

Storage Humidity (Environment) 10% ~ 90% Non-condensing


Power, ESD, Regulatory

Maximum Power Consumption 6.5W

ESD Protection 15KV

Regulatory CE, FCC

Other

Standard Warranty 3 Year

Indicators 1 Power, 1 Input status, 4 Output connection

status

Included Items

Installation guide, Power adaptor, Mounting “L”

brackets (2 ea), Mounting screws (4 ea), Plastic

cushions (4 ea)

4.1 Supported Input Video Formats

Input Resolution HDMI DVI 720 x 480@60Hz R R 720 x 480I@30Hz R R 720 x 576@50Hz R R 720 x 576I@25Hz R R 1280 x720@50Hz R R 1280 x720@60Hz R R 1920 x 1080@25Hz R R 1920 x 1080@50Hz R R 1920 x 1080@60Hz R R 1920 x 1080I@25Hz R R 1920 x 1080I@30Hz R R 3840 x 2160@25Hz R 3840 x 2160@30Hz R 3840 x 2160@60Hz R 1080P 3D@60Hz R

1


www.tlnetworx.com

5. Panel Drawing

2 www.tlnetworx.com


6. Troubleshooting & Maintenance Problems Causes Solutions

Color loss or no video

signal output on the

HDMI display

The connecting cables may not be connected correctly or it may be broken.

Check whether the cables are connected correctly and are in working condition.

The display is not compatible with the present output resolution.

Make sure the resolution of the display(s) is compatible with the present resolution.

No HDMI signal output

from the TL-DA14-HD2

while local HDMI input is

in normal working state

The connecting cables may not be connected correctly or it may be broken.

Check whether the cables are connected correctly and in working condition.

Screen blinking Poor quality of the

connecting cable

Change for another cable

of good quality.

Static becomes stronger

when connecting the

video connectors

Bad grounding

Check the grounding and

make sure it is connected

well.

If your problem persists after following the above troubleshooting steps, please contact your authorized reseller or TechLogix technical support.

3 www.tlnetworx.com


7. After-sales Service 1) Product Limited Warranty: We warrant that our products will be free from defects in

materials and workmanship for three years. 2) Warranty coverage may be voided when:

l The warranty period has expired l The factory applied serial number has been altered or removed from the product l There is damage, deterioration or malfunction caused by:

l Atypical wear and tear l Use of supplies or parts not meeting the specifications l No certificate or invoice as the proof of warranty l Damage caused by force majeure l Non-authorized service

3) Technical Support: When contacting TechLogix support, please have the following information available: l Product part number l Installation and sale date l Detailed failure information

160926 TL-DA14-HD2 Manual - Future Ready Solutions · The TL-DA14-HD2 is a 1x4 splitter featuring...

Documents

Transcript of 160926 TL-DA14-HD2 Manual - Future Ready Solutions · The TL-DA14-HD2 is a 1x4 splitter featuring...