1/6 Imperial German Infantryman Assembly Guide

1
Follow these steps for a perfectly arranged knapsack. 1. Cut several cardboard squares: 3 cm wide by 3.5 cm high. Stack two to three pieces of card- board to achieve 1 cm thickness. Bind pieces together with tape. 2. Insert the cardboard stiffener into the main storage compartment of the pack, then close the inside flaps. 3. Load the tent equipment bag with tent poles, tent stakes, and tent rope. Attach tent equipment bag in- side the knapsack, then close the pack and buckle. 4. Insert the three short knapsack straps into the top and side loops as shown. 5. The thin gray cloth simulates the greatcoat for the pack assembly. Roll into a tight roll, and set aside. 6. Fold the tent square into eight long folds. 7. Center the tent square and cloth at the top of the pack. Wrap a short knapsack strap loosely around the tent square/cloth, then run the strap through the buckle. Press the tent square/cloth tightly to the knapsack with your finger, and gently tighten the strap until you find the best buckle hole. 8. Wrap the tent square/cloth around the side of the knapsack. The tent square will be longer than the cloth, and should be wrapped around each end of the cloth. Wrap the knapsack strap loosely around the tent square/cloth. Tighten the strap while pressing tent FIRMLY. Find the best buckle hole, but don’t pull so tightly as to break the strap. Repeat on the other side. 9. The thickness of the tent square/cloth may pull the bottom of the pack out. Pinch the sides of the assembled pack and apply clear tape (body side) to create a more squared appearance of the pack. 10. Attach mess kit to the back of the pack with the two long leather straps. Finally, pass the Y-Straps over the shoulders of the figure and attach the two large hooks to the D-Rings on the ammunition pouch. The side straps attach to the bottom of the pack. Assembling the Knapsack © Timewalker Enterprises, Inc. ASSEMBLY GUIDE CalTek Imperial German Infantryman, Battle of Liege, 1914 YOU WILL NEED: Knapsack Gray Cloth Tent Equipment Bag Tent poles (3) Tent Stakes (3) Tent Rope Knapsack Straps (3 short) (2 long) Tent Square Mess Kit Fill the tent equipment bag. Wrap the tent and gray cloth and fasten with short strap. Tighten the pack with clear tape. Recommended: fill the pack with some cardboard. In One-Sixth Scale See step-by-step photos and detailed instructions at http://goo.gl/fzdz5. The cover was engineered to be a tight fit on the helmet. Follow these instructions for the best fit. 1. The cover has five attachment hooks: three to the front and two to the rear. 2. Push the spike of the helmet firmly into the cloth cone of the cover with the numbers facing front. 3. Attach the center front hook (1) first. 4. Attach rear hook (2) next, and then rear hook (3). Smooth the helmet cover with your fingers as you go. 5. Attach front hook (4), and then front hook (5). Be mindful of the helmet chin strap, as it may get in the way. See more pictures and assembly instructions. http://goo.gl/9vLhE Putting the Helmet Cover on the M1895 Pickelhaube See equipment details at http://goo.gl/w7ggk. This is the regulation arrangement of field equipment on the belt for the Imperial German Infantryman. First, string the bayonet knot onto the leather frog as shown in the picture to the right. Load the belt in the following order as shown above: first, the ammunition pouch, then the bread bag and canteen combination, [leave some space], next the entrenching tool and bayonet combination, then the second ammunition pouch. Hook the belt around the waist of the figure, then straighten. The Y-Straps will hook onto the D-Rings at the top of the ammunition pouches. Assembling the Equipment on the Belt ASSEMBLY GUIDE CalTek Imperial German Infantryman, Battle of Liege, 1914 In One-Sixth Scale 1 2 3 4 5 © Timewalker Enterprises, Inc.

description

These quick instructions will show you how to assemble the pack, belt and helmet cover of the Caltek-Timewalker 1/6 Imperial German Infantryman 1914 Collectible Figure. Created for our customers and shared for all by Timewalker Enterprises, Inc.

Transcript of 1/6 Imperial German Infantryman Assembly Guide

Page 1: 1/6 Imperial German Infantryman Assembly Guide

Follow these steps for a perfectly arranged knapsack.

1. Cut several cardboard squares: 3 cm wide by 3.5 cm high. Stack two to three pieces of card-board to achieve 1 cm thickness. Bind pieces together with tape.

2. Insert the cardboard sti� ener into the main storage compartment of the pack, then close the inside � aps.

3. Load the tent equipment bag with tent poles, tent stakes, and tent rope. Attach tent equipment bag in-side the knapsack, then close the pack and buckle.

4. Insert the three short knapsack straps into the top and side loops as shown.

5. The thin gray cloth simulates the greatcoat for the pack assembly. Roll into a tight roll, and set aside.

6. Fold the tent square into eight long folds.

7. Center the tent square and cloth at the top of the pack. Wrap a short knapsack strap loosely around the tent square/cloth, then run the strap through the buckle. Press the tent square/cloth tightly to the knapsack with your � nger, and gently tighten the strap until you � nd the best buckle hole.

8. Wrap the tent square/cloth around the side of the knapsack. The tent square will be longer than the cloth, and should be wrapped around each end of the cloth. Wrap the knapsack strap loosely around the tent square/cloth. Tighten the strap while pressing tent FIRMLY. Find the best buckle hole, but don’t pull so tightly as to break the strap. Repeat on the other side.

9. The thickness of the tent square/cloth may pull the bottom of the pack out. Pinch the sides of the assembled pack and apply clear tape (body side) to create a more squared appearance of the pack.

10. Attach mess kit to the back of the pack with the two long leather straps. Finally, pass the Y-Straps over the shoulders of the � gure and attach the two large hooks to the D-Rings on the ammunition pouch. The side straps attach to the bottom of the pack.

Assembling the Knapsack

© Timewalker Enterprises, Inc.

ASSEMBLY GUIDE CalTek Imperial German Infantryman, Battle of Liege, 1914

YOU WILL NEED:

KnapsackGray Cloth

Tent Equipment BagTent poles (3)Tent Stakes (3)

Tent RopeKnapsack Straps

(3 short) (2 long)Tent Square

Mess Kit

Fill the tent equipment bag.

Wrap the tent and gray cloth and fasten with short strap.

Tighten the pack with clear tape.

Recommended: � ll the pack with some cardboard.

In One-Sixth Scale

See step-by-step photos and detailed instructions at http://goo.gl/fzdz5.

The cover was engineered to be a tight � t on the helmet. Follow these instructions for the best � t.

1. The cover has � ve attachment hooks: three to the front and two to the rear.

2. Push the spike of the helmet � rmly into the cloth cone of the cover with the numbers facing front.

3. Attach the center front hook (1) � rst.

4. Attach rear hook (2) next, and then rear hook (3). Smooth the helmet cover with your � ngers as you go.

5. Attach front hook (4), and then front hook (5). Be mindful of the helmet chin strap, as it may get in the way.

See more pictures and assembly instructions.http://goo.gl/9vLhE

Putting the Helmet Cover on the M1895 Pickelhaube

See equipment details athttp://goo.gl/w7ggk.

This is the regulation arrangement of � eld equipment on the belt for the Imperial German Infantryman.

First, string the bayonet knot onto the leather frog as shown in the picture to the right.

Load the belt in the following order as shown above: � rst, the ammunition pouch, then the bread bag and canteen combination, [leave some space], next the entrenching tool and bayonet combination, then the second ammunition pouch.

Hook the belt around the waist of the � gure, then straighten. The Y-Straps will hook onto the D-Rings at the top of the ammunition pouches.

Assembling the Equipment on the Belt

ASSEMBLY GUIDE CalTek Imperial German Infantryman, Battle of Liege, 1914In One-Sixth Scale

1

23

4 5

© Timewalker Enterprises, Inc.