1

ASSEMBLY AND OPERATING INSTRUCTIONSFeatures of Your New XTM Racing 1/6 Gas-Powered 2WD Buggy:

● Incredible 1/6 Scale Size!● Includes 23cc Gasoline Engine with Pull-Starter● Steel Differential● Full Ball Bearings● Huge Front Bumper● Factory-Trimmed Body● Double Epoxy Brake Discs● Strong 7mm Thick Dogbones● Heavy-Duty Side Dust Guards● Factory-Glued Tires with Inserts

● Internal Roll Cage for Protection● Massive Servo Saver for Steering● Fully Threaded, Oil-Filled Aluminum Shocks● Dust Cover to Protect the Pinion and Spur Gears● Adjustable Camber, Castor and Toe-In Front and Rear● 4mm Aluminum Chassis with Curved Edges for More Strength● Uses Regular Unleaded Gasoline with 2-Stroke Oil Added● Water-Resistant Receiver and Battery Boxes● Large Fuel Tank with Ventilation Lines● Large Pull-Starter for Easy Starting

Thank you for purchasing the XTM Racing 1/6 Gas-Powered 2WD Buggy. These Assembly and Operating Instructions are provided to help you enjoyyour new 1/6 Gas-Powered 2WD Buggy without any of the hassles you might expect. Please read through all of the literature that is provided in the box.

✦✦✦✦✦IMPORTANT✦✦✦✦✦ Before operating your new 1/6 Gas-Powered 2WD Buggy, please read and understand the warnings listed on the next page. Failureto do so could lead to bodily harm and/or injury. The XTM Racing 1/6 Gas-Powered 2WD Buggy is not intended for persons under 12 years of age,unless closely supervised by an adult.

The XTM Racing 1/6 Gas-Powered 2WD Buggy is distributed exclusively in the U.S.A.byGlobal Hobby Distributors

18480 Bandilier CircleFountain Valley, CA 92708

All contents copyright © 2004, Global Hobby Distributors Version V1.0 July 2004

Kit Product # 146300

1/6 GAS-POWERED 2WD BUGGY

2

ENGINE WARNINGS

● Never use any fuel in your engine other than regular unleadedgasoline with 2-stroke oil added. Use of any other types of fuel,such as glow fuels for nitro-powered engines and diesel fuelshould never be used.

● Never operate your model on any public streets. This couldcause traffic accidents, personal injury or property damage.

● Gas engines emit exhaust vapors that are poisonous and canbe dangerous to your health. It is important that you operateyour engine in a very well-ventilated area, preferably outdoors.

● Before starting your engine, make sure that the throttle trim isset to the idle position. Starting your engine at any setting aboveidle can cause the model to lurch out of your hands.

● When your engine is running, there are certain parts thatrotate at high speeds. Be careful not to touch the drive shafts,gears, clutch assembly or any other moving parts. Otherwise,serious injury could result.

● It is normal for your engine and muffler to get very hot duringoperation. Never touch these parts while they are hot or youmight be burned.

● Model car engines produce vibration when they are running. Itis important to periodically check the engine mounting screwsand other assemblies to ensure they are tight. Running yourengine with the engine mounting screws loose can lead tosevere engine and/or chassis damage.

FUEL WARNINGS

● The gasoline used in your 1/6 Gas-Powered 2WD Buggy ispoisonous. Follow all safety precautions and keep gasoline in atightly sealed container specifically for this purpose.

● Keep fuel out of the reach of children.

● Gasoline and its vapors are extremely flammable. Keep awayfrom high heat, sparks and flame.

GENERAL WARNINGS

● Under no circumstances should you operate your model incrowds of people. Serious injury could result.

● Never operate your model on busy streets or if there are carsaround.

● Do not use your model to chase pets or other animals.

● The receiver and battery boxes are not waterproof; therefore,do not drive through water, wet grass, mud or snow.

● Because your model is operated by radio control, it is importantto make sure you always are using fresh and/or fully chargedbatteries. Never allow the batteries to run low or you could losecontrol of the model.

● If your model becomes stuck, allow the engine to idle, thenretrieve your model by hand.

● To prevent excessive r.p.m.'s from damaging your engine and/ordrivetrain components, we suggest reducing throttle while in theair during jumps.

FOR YOUR SAFETY - PLEASE READ THESE WARNINGS FIRST!

If you should have trouble with any of the steps listed in these Assembly and Operating Instructions, or if you find a missing or damagedpart in your kit, please contact us at the address below:

CUSTOMER INFORMATION

Global Services18480 Bandilier CircleFountain Valley, CA 92708

Phone: (714) 963-0329 Fax: (714) 964-6236 Email: service@globalhobby.net

To allow us to serve your needs better, please include your email address with any correspondence you send to us. Your email address will be added to our CustomerService Database so you will automatically receive free updates and tech notices for your particular product. You will also receive repair status updates (if applicable) andother important information about your product as it becomes available.

IMPORTANT INFORMATION ABOUT YOUR EMAIL ADDRESSGlobal Hobby Distributors will not disclose the information it collects to outside parties. Global Hobby Distributors does not sell, trade, or rent

your personal information to others . Your privacy is important to us.

CHECK IT OUT! We urge you to come check out our website at http://globalservices.globalhobby.com. There you will find public message boardsfrequented by other XTM Racing product owners and the XTM Racing support staff. This is a great place to learn about new XTM Racing products,get help and suggestions for your current XTM Racing products or just simply hang out and chat with people that share your same interests.

Check out our website for more information onthis and other exciting XTM Racing products!

http://xtm.globalhobby.com

3

TOOLS NEEDED FOR ASSEMBLY

PHILLIPS HEAD SCREWDRIVERS(# 1 AND # 2 SIZES)

MODELING KNIFE

WIRE CUTTERS

C/A GLUENEEDLE NOSE

PLIERS

1.5MM, 2MM AND 2.5MMHEX WRENCHES

RADIO CONTROL SYSTEM REQUIRED

RECEIVER

SUB-C 6VRECEIVER

BATTERY PACKSWITCH

HARNESS

STEERINGSERVO

THROTTLE/BRAKESERVO

PLEASE READ AND UNDERSTAND THE INSTRUCTIONS PROVIDED WITH YOUR RADIO CONTROL SYSTEMBEFORE INSTALLING IT INTO YOUR 1/6 GAS-POWERED 2WD BUGGY.

Before installing the servos, the servo outputshafts must be centered. To set the centerposition, turn on the transmitter and receiver. Setthe trim levers on the transmitter to the centerposition and turn off the receiver, then thetransmitter. At this point, the servo output shaftswill be in the centered position and are ready forinstallation.

For the steering servo, we strongly recommendusing a 1/4 scale servo that has a minimum of200 oz./in. torque at 6 volts.

For the throttle/brake servo, we suggest using ahigh-quality standard servo with a minimum of60 oz./in. torque at 6 volts.

Although an AM radio control system can be used, werecommend using an FM radio control system.

We suggest using a Sub-C size 6 volt batterypack with a minimum capacity of 2000mAH.

YOU WILL ALSO NEED HIGH-QUALITY 2-STROKE ENGINE OIL TO MIX WITH THE REGULAR UNLEADED GASOLINE USEDIN THE ENGINE. THE OIL SHOULD BE MIXED AT A RATIO OF 32:1 (i.e. 32 PARTS GASOLINE TO 1 PART 2-STROKE OIL).

4

When installing the servos, both servos'output shafts should be toward the REARof the chassis.

Certain servos may require the use of theincluded spacers to mount properly. Thiswill be dependent on brand and type, andmay not be required for all servos.

5

6

7

8

9

10

11

Use only Regular Unleaded gasoline with an Octane rating of 89 to 91 in your engine. It's very important to add ahigh-quality 2-stroke engine oil to the gasoline at a ratio of 32:1 (i.e. 32 parts gasoline to 1 part 2-stroke oil).

When it's time to replace the spark plug, we strongly suggest using only the OEM brand spark plug designed specificallyfor the engine. Use of any other type of spark plug may result in engine damage and/or poor engine performance.

Your engine comes equipped with astandard air filter that includes a foamfilter element. As a precaution, werecommend that you change or cleanthe air filter element on a regular basis.

To ensure the long life of your engine,we strongly suggest "wetting" the air fil-ter element with Air Filter Oil after youclean or replace the air filter element.

The high and low speed mixture screwscome preset from the factory for initialstarting and running. Do not adjust themat this time.

Starting a Cold Engine:

Set the carburetor throttle lever to the idle position, then choke the engine by closing the choke lever. Press the primerpump until it is filled with fuel. Slowly pull out the pull-start cord until you begin to feel resistance, then pull strongly onthe pull-start cord until you hear the engine ignite. Normally, the engine will immediately stop after this first ignition. Now,open the choke lever and pull the pull-start cord firmly until the engine starts. To stop the engine, press and hold theignition switch until the engine stops.

☞☞☞☞☞ Hold the model firmly with your free hand when pulling on the pull-start cord.

Spark plug gap should be set to 0.7mm - 0.8mmOEM replacement spark plug part # 32730

12

Starting a Warm Engine:

Set the carburetor throttle lever to the idle position, but leave the choke leveropen. Press the primer pump until it is filled with fuel. Pull the pull-start cordfirmly until the engine starts. To stop the engine, press and hold the ignitionswitch until the engine stops.

☞☞☞☞☞ Hold the model firmly with your free hand when pulling on the pull-start cord.

Adjusting the Carburetor (Low Speed):

The carburetor adjustment screws are preset from the factory for initial running. Depending on many factors, such aslocal weather conditions, air filter and muffler, the carburetor settings may need to be changed. Drive the car at mediumRPM until the engine has reached normal operating temperature. If after the engine is warmed up the engine deceleratesa little during acceleration, the engine is too lean. In this case, turn the Low Speed Mixture Screw counterclockwise(richen). If the engine stutters and lots of smoke comes from the exhaust during acceleration, the engine is too rich. Inthis case, turn the Low Speed Mixture Screw clockwise (lean). When set properly, the engine should accelerate withouthesitation from idle to full power.

Adjusting the Carburetor (High Speed):

To adjust the engine for maximum RPM, carefully lift the car so that the rear wheels are off the ground. With the enginewarmed up to normal operating temperature, hold the throttle wide open for a short time. If the engine is running rich, turnthe High Speed Mixture Screw clockwise (lean) until full power is achieved. If the engine is running lean, turn the HighSpeed Mixture Screw counterclockwise (richen) until full power is achieved. After adjusting the High Speed MixtureScrew, it may be necessary to readjust the Low Speed Mixture Screw, since they interact with each other.

✦✦✦✦✦WARNING✦✦✦✦✦ Don't keep the engine running at full power for any longer than necessary with the rear wheels off theground. Running the engine for too long without a load can cause severe engine damage.

Resetting the Mixture Screws to the Factory Settings:

To reset the mixture screws to the factory settings, first close both mixture screws by turning them clockwise GENTLY. Toreset the Low Speed Mixture Screw, turn the screw counterclockwise from the fully closed position 1.25 turns. To resetthe High Speed Mixture Screw, turn the screw counterclockwise from the fully closed position 1.5 turns.

✦✦✦✦✦WARNING✦✦✦✦✦ For the first two tanks of fuel, you should avoid running the engine at full RPM for any length of time. Thiswill keep the engine from getting too hot during the short break-in period. You should also range check your radio systemwhile the engine is running to ensure there is no interference caused by the ignition system and/or vibration.

13

This troubleshooting guide has been provided to help you diagnose and solve most problems that you may encounter with the engine inyour 1/6 Gas-Powered 2WD Buggy. Most problems encountered can be solved by carefully following the problem-cause-solutionsections. If you cannot solve the problem using this troubleshooting guide, please feel free to contact us at the address, phone numberor email address shown on the second page of these Assembly and Operating Instructions.

ENGINE TROUBLESHOOTING GUIDE

PROBLEM CAUSE SOLUTION

1) Spark plug A) Spark plug electrode wet A) Remove spark plug and dry electrodeB) Carbon deposits on electrode B) Remove spark plug and clean electrodeC) Spark plug insulator damaged C) Replace spark plugD) Incorrect gap setting D) Reset gap to 0.7mm - 0.8mmE) Spark plug electrode damaged E) Replace spark plug

2) Magneto A) Ignition coil failure A) Replace ignition coilB) Damaged spark plug cable B) Replace spark plug cableC) Loose or disconnected spark plug cable C) Push spark plug cable firmly onto spark plug

3) Switch A) Switch is off A) Turn switch onB) Switch has failed B) Replace switchC) Wiring damaged C) Repair wiring

ENGINE DOES NOT START

ENGINE DOES NOT RUN

PROBLEM CAUSE SOLUTION

1) Engine not drawing fuel A) Clogged breather air hole A) Clean breather air holeB) Clogged carburetor B) Clean carburetorC) Clogged fuel filter C) Clean and/or replace fuel filter

2) Poor compression A) Worn cylinder, piston and/or piston ring A) Check and replace as neededB) Leak between cylinder head and crankcase B) Replace cylinder head gasket

3) Engine will not run A) Engine is flooded A) Purge excess fuel from crankcaseB) Carburetor settings too rich B) Readjust carburetor settingsC) Clogged air cleaner C) Clean air cleaner filter elementD) Old and/or contaminated fuel D) Use new fresh fuel

ENGINE RUNS POORLY AND/OR HAS LACK OF POWER

PROBLEM CAUSE SOLUTION

1) Engine Overheats A) Carburetor adjustments too lean A) Readjust carburetorB) Incorrect fuel/oil mixture B) Mix fuel and oil at a ratio of 32:1C) Spark plug faulty or failed C) Replace spark plugD) Cylinder head cooling fins blocked D) Clean debris from between cooling finsE) Inadequate airflow over engine E) Increase airflow over engine

2) Engine has lack of power A) Air leak in engine and/or fuel system A) Tighten all engine bolts and fuel system jointsB) Old and/or contaminated fuel B) Use new fresh fuelC) Piston begins to seize C) Replace piston, cylinder and ringD) Muffler has accumulated carbon deposits D) Clean mufflerE) Carburetor settings out of adjustment E) Readjust carburetorF) Clogged air cleaner F) Clean air cleaner filter elementG) Engine is overloaded G) Reduce engine load

14

SPARE PARTS LIST

XTM Racing stocks a complete line of replacement parts for your 1/6 Gas-Powered 2WD Buggy and 23cc Gasoline Engine. Listed onthe next few pages are the replacement parts that are available along with their respective part numbers for easy ordering convenience.

We suggest ordering directly from your local XTM Racing dealer. If your local dealer doesnot stock XTM Racing or Global products, you can order directly from us at the phone

number or address shown on page # 2.

15

SPARE PARTS LIST, CONTINUED...

32601 Cylinder Head32602 Cylinder Head Gasket32603 Cylinder Head Screw Set M5x2232604 Carburetor Mounting Insulator32605 Carburetor Mounting Insulator Gasket32606 Carburetor Gasket32607 Carburetor Mounting Screw Set M5x2032608 Muffler Assembly32609 Muffler Mounting Screw Set32610 Muffler Gasket32611 Screw M4x1232612 Crankcase32613 Alignment Pin32614 Crankcase Gasket32615 Ball Bearing32616 Rear Shaft Seal32617 Front Shaft Seal32618 E-Ring32619 Crankcase Screw Set M5x3032773 Piston32621 Piston Ring32622 Wrist Pin32623 Wrist Pin Retaining Ring32774 Wrist Pin Bearing32775 Wrist Pin Washer32626 Crankshaft32627 Crankshaft Nut32628 Woodruff Key32629 Crankshaft Shim32630 Clutch Shoes32631 Clutch Spring32632 Clutch Retaining Screw M6x2232633 Clutch Washer-Rear32634 Clutch Washer-Front32635 Clutch Housing32636 Clutch Housing Screw M5x1632637 Clutch Driver32638 Washer Head Screw M6x1432639 Rotor32640 Ignition Coil32642 Spark Plug Cap32643 Spark Plug Cap Spring32644 Rubber Socket32645 Ignition Coil Mounting Spacer32646 Ignition Coil Mounting Screw M4x2032647 Pull-Start Assembly32649 Recoil Spring32650 Cord Spool32651 Ratchet32652 Spring32653 Screw32654 Retainer32655 Washer32656 Pull-Start Cord32657 Pull-Start Handle32658 Pull-Start Mounting Screw Set M4x1632659 Carburetor Assembly32660 Screen32661 Lower Cover32662 Lower Cover Mounting Screw

32663 Lower Gasket32664 Diaphragm-Lower32665 Upper Gasket32666 Diaphragm-Upper32667 Carburetor Body-Upper32668 Carburetor Upper Cover32669 Bulb Pump32670 Spring32671 Valve Inlet32672 Plug32673 Lever32674 Screw32675 Pin32676 Screw32677 Spring32678 Throttle Shaft32679 Spring32680 Screw32681 Throttle Valve32682 Screw32683 Throttle Lever32684 Ring32685 Choke Shaft32686 Choke Lever32687 Spring32688 Ball32689 Screw32690 Spring32691 Idle Needle32692 Spring32693 High Speed Needle32694 Small Screen32695 Ring32696 Plug32698 Choke Lever32699 Spacer32700 Screw M5x6032701 Air Filter A32702 Housing32703 Cover32704 Filter32705 Sleeve32706 Fan Cover32707 Screw M5x2032708 Cylinder Head Cover32709 Screw M4x1232710 Screw TP4.5x18L32711 Switch A32712 Fuel Pipe32713 Fuel Filter32714 Clip32715 Socket32716 Case32717 Screw M5x5032723 Pull-Starter Label32726 Puller (Option)32727 Piston Stop (Option)32728 Spark Plug (Option)32729 Spring (Option)32730 Spark Plug

16

SPARE PARTS LIST, CONTINUED...

146311 (002160)Ball Bearing 10x22x6

146310 (002159)Ball Bearing 8x22x7(2)

146312 (002161)Ball Bearing 12x28x7

146313 (11310)Antenna Tubes (5)

146314 (11311)Antenna Caps (10)

146315 (11333)M3 Set Screws (10)

146316 (11399)Body Pins (10)

146317 (11447)M3 Lock Nuts (10)

146318 (11922)M5 Lock Nuts (5)

146319 (11923)M4 Lock Nuts (5)

146320 (32400)Spur Gear Mount-Nylon

146321 (32401)Servo Tray

146322 (32402)Roll Cage-Front (A)

146323 (32403)FR Upper Susp Arm-Left

146324 (32404)FR Lower Susp Arm-Left

146325 (32405)RR Lower Susp Arm-Left

146326 (32406)RR Upper Susp Arm-Left

146327 (32407)Rear Bulkheads for Diff

146328 (32408)Rear Axle Hubs

146329 (32409)Ball Ends "B" (8)

146330 (32410)RR Upper Turnbuckles

146334 (32414)Front Bulkhead-Plate1

146331 (32411)Engine Mount-Left

146332 (32412)Front Bulkhead-Plate 2

146333 (32413)Rear Shock Tower

146335 (32415)Side Gear Plate

146339 (32419-1)Side Dust Guards (L&R)

146338 (32418)Differential Housing

146337 (32417)FR Steering Arms (L&R)

146336 (32416)Upper Steering Bellcrank

146340 (32420)Roll Cage Tubes (C)

146342 (32422)Pinion Gear 18T-Nylon

146343 (32423)Upper Hinge Pins

146341 (32421)Spur Gear 46T

146344 (32424)RR Inner Upper Hinge Pins

146345 (32425)M5 E-Rings (12)

146346 (32426)Ball Bearings 10x19x7 (5)

146349 (32430)M4x8 Flat Head Screws (5)

146348 (32428)Fuel Tank Cap Assembly

146347 (32427-1)Body Set w/Decals

17

SPARE PARTS LIST, CONTINUED...

146351 (32432)M4x16 F.H. Screws (5)

146350 (32431)M4x8 R.H. Screws (5)

146352 (32433)Differential - Complete

146353 (32434)M5x25 F.H. Screws (5)

146354 (32435)M5x25 Set Screws (5)

146355 (32436)Lower Shock Mounts (2)

146356 (32437)M5x4 Set Screws (5)

146357 (32438)M4x4 Set Screws (5)

146358 (32439)M5x41 C.H. Screws (5)

146359 (32440)M4x24 C.H. Screws (10)

146360 (32441)M3x23 C.H. Screws (5)

146361 (32442)M4.2x16 S.T. Screws (10)

146363 (32444)M5x10 Set Screws (5)

146364 (32445)Diff Housing Sleeve

146362 (32443)M4.2x25 S.T. Screws (5)

146365 (32446)5x10 Ball Ends (5)

146366 (32447)4x10 Ball Ends (4)

146367 (32448)6.5x12x1.5 Washers (5)

146368 (32449)8.4x117x1 Washers (5)

146369 (32450)Body Only

146370 (32451)16T Layshaft Gear

146371 (32452)Main Diff Gear-48T

146372 (32453)Clutch Bell

146373 (32454)Diff Spider Gears w/Shaft (2)

146374 (32455)Diff Bevel Gears (2)

146375 (32456)Front Square Hub

146376 (32457)Spacer Sleeves (3)

146377 (32458)Rear Wheel Axles (2)

146378 (32459)Diff Output Shafts (2)

146379 (32460)Chassis-4mm

146380 (32461)Rear Brace Plate

146381 (32462)Rear Square Hub

146382 (32463)FT Upper Turnbuckles (2)

146383 (32464)Front Axles (2)

146384 (32465)Rear Drive Shafts (2)

146385 (32466)Front Brace Plate

146386 (32467)Throttle Linkage

146387 (32468)Turnbuckles/RR Lower Arms

146388 (32469)Brake Hub

146389 (32470)Brake Rod

18

SPARE PARTS LIST, CONTINUED...

146391 (32472)Brake Pads

146390 (32471)Brake Cam & Lever

146392 (32473)Fuel Line

146393 (32474)Engine Mount Washers (4)

146394 (32475)Rear Layshaft

146395 (32476)Spacers/Brakes

146396 (32477)Spring/Servo Saver

146397 (32478)M4 Collars (5)

146398 (32479)M2 Collars (5)

146399 (32480)Bearing Spacers (8)

146400 (32481)Rear Chassis Guard

146404 (32485)Side Body Posts (4)

146405 (32486)Roll Cage Tubes

146406 (32487)Engine Mount-Right

146407 (32488)FR Shocks w/Springs

146408 (32489)Front Body Post

146409 (32490-1)Front Bumper

146410 (32491-1)Battery Cover

146411 (32492)Roll Cage Rear Section

146412 (32493)Vent Line "Y" Connector

146413 (32494-1)Fuel Tank Assembly

146414 (32495)Front Shock Towers (2)

146415 (32496)Rear Wing

146416 (32497-1)Receiver Case

146417 (32498)FR Hinge Pins (4)

146418 (32499)RR Lower Hinge Pins (2)

146420 (32521-1)Main Gear Cover

146421 (32522)Fuel Tank Key

146422 (32523)M6 Ball Ends (4)

146423 (32524)Servo Spacers

146424 (32525)Servo Plates (2 Pair)

146425 (35545)FR Upper Susp. Arm-Right

146426 (32546)FR Lower Susp. Arm-Right

146427 (32547)RR Lower Susp. Arm-Right

146428 (32548)RR Upper Susp. Arm-Right

146429 (32549)Shock Shafts (4)

146430 (32550)Lower Shock Mounts (4)

146401 (32482)Wheels (1 PR)

146402 (32483)Tires w/Inserts (1 PR)

146403 (32484)Mounted Tires (1 PR)

19

SPARE PARTS LIST, CONTINUED...

146432 (32552)Upper Shock Mounts (4)

146431 (32551)Shock Adjusting Rings (4)

146433 (32553)Shock Caps (4)

146434 (32554)Shock Pistons (4)

146435 (32555)Shock Cap Seals (4)

146436 (32556)Shock Spring Retainers

146437 (32557)Shock Body-Rear (2)

146438 (32558)Shock Body-Front (2)

146439 (32559)Shock Spring-Front (2)

146440 (32560)Shock Spring-Rear (2)

146441 (32561)M4.2x16 R.H. S.T. Screws (10)

146445 (32565)M5x30 F.H. Screws (5)

146446 (32566)M5x10 F.H. Screws (5)

146447 (32567)M3x12 R.H. Screws (10)

146448 (32568)M6 Lock Nuts (5)

146449 (32569)Brake Discs (2)

146450 (32570)M7 E-Rings (10)

146451 (32571)Exhaust Pipe

146452 (32572)Steering Turnbuckles

146453 (32573)Gear Bushing

146454 (32574)Rear Shocks w/Springs

146456 (32576)4.4x11x1 Washers (10)

146457 (32577)Window Net Set

146458 (32578)Servo Saver

146459 (32579)Steering Post

146460 (32580-1)Decal Sheet

146461 (32900)23cc Gas Engine

146442 (32562)M4x30 C.H. Screws (5)

146443 (32563)M6x16 Hex Screws (5)

146444 (32564)M4x43 C.H. Screws (5)

No PhotoAvailable

146419 (32520-1)Instruction Manual

20

IMPORTANT WARRANTY SERVICE INFORMATION

Before returning your 1/6 Gas-Powered 2WD Buggy for warranty consideration, the status of the unit must be within the guarantee asstated above. Do not return your 1/6 Gas-Powered 2WD Buggy to the place of purchase. They are not authorized or equipped toperform warranty work on XTM Racing products. When requesting warranty service, please observe the following:

● Crash damage will not be covered under warranty. Do not request warranty service for a crash-damaged product.

● This warranty only covers the XTM Racing 1/6 Gas-Powered 2WD Buggy and the factory-installed 23cc gas engine. It does notcover after-market engines or your radio control system and other electronics. Wear items, such as spark plug, clutch shoes, tires andbrake discs are not covered under warranty. Please remove radio control system from the chassis before sending the product to us.

● Include a note detailing the problem or service you are requesting. Service cannot be provided without this information. Includeyour daytime phone number, shipping address and/or email address in the event we need more details pertaining to the servicerequested.

● If your vehicle is out of the warranty period you may request an estimate of services at the time you return your vehicle for service.An omission of this request implies permission for Global Services to service your vehicle at our discretion.

● Include a method of payment for any service charges.

● Send the unit to us by United Parcel Service, Federal Express or by Insured Mail. Postage is non-refundable. Send yourpackage to:

IMPORTANT WARRANTY INFORMATION - PLEASE READ!

Your XTM Racing 1/6 Gas-Powered 2WD Buggy is warranted against manufacturer defects in materials and workmanship for a periodof 90 days from the date of purchase. This does not cover any component parts damaged by use, misuse or modification. In no caseshall XTM Racing's liability exceed the original cost of the purchased kit. Warranty service will be provided within 90 days of thedate of purchase only if you are able to provide the original or a copy of the original dated sales receipt.

In that XTM Racing has no control over the final assembly or material used for final assembly, no liability shall be assumed for anydamage resulting from the use by the user of the final user-assembled product. By the act of using the final user-assembledproduct, the user accepts all resulting liability.

Visit Our Websitehttp://globalservices.globalhobby.com

Global Services18480 Bandilier CircleFountain Valley CA 92708

Phone: (714) 963-0329 Fax: (714) 964-6236 Email: service@globalhobby.net