Powerful Stripping Action

Hillyard Super Strip will easily remove the toughest buildup on the floor. Even floors thathave been repeatedly burnished and hardened with multiple coats of finish are rapidlystripped. Super Strip is formulated to provide powerful stripping action no matter whatthe condition of the floor.

Works Fast

Simply mix in cold water (1:10 for normal buildup or 1:5 for heavy buildup), let sit for10 minutes, and then agitate the dissolved finish with a black pad or mop. Remove thesolution from the floor with a wet vacuum. Use Hillyard Nutra-Rinse to rinse andneutralize freshly stripped floors.

Lowers the Cost of Shipping

The high performance stripping action of Super Strip results in a successful outcome anda better looking floor every time. The intense process of stripping is easy with thesuperior stripping ability of Hillyard Super Strip. Time and labor-saving benefits are builtin, every time you use it.

Quality In Any Situation

Hillyard Super Strip is extremely versatile and works well in a wide variety of conditions.It will strip any finish or sealer in almost any situation. Hillyard Super Strip isconveniently packaged in 2 1/2 gallon containers, with two containers per carton, and55 gallon drums. Ask your Hillyard sales consultant about the benefits of cleaning withHillyard Super Strip.

HILLYARDSUPER STRIP

Removes Stubborn Floor Finishes And Sealers Fast

© 2004, Hillyard, Inc., "CHECKERBOARD" Trademark ®

A s s i s t®C l e a n

H I L L Y A R D

#152

HILLYARD

SUPER STRIPLABEL INFORMATION #152

TECHNICAL DATA

®

HILLYARD, INC. • P.O. Box 909 • St. Joseph, MO 64502 • Telephone: 1-800-365-1555 • www.hillyard.com

READ LABEL ANDMSDS BEFORE USING

0704 (#152)

RECOMMENDED FOR REMOVING WATER-BASED ACRYLIC AND URETHANEFORTIFIED FLOOR FINISHES FROM RESILIENT AND HARD FLOORS

DIRECTIONS: Do not use on asphalt tile, linoleum, synthetic sports floors, rubber, painted, or varnished surfaces. (DO NOT USE ON WOOD.)PRETEST: Pretest in small area for color bleeding or discoloration or softening that may occur on linoleum, rubber, or asphalt tile on an inconspicuous area.Do not continue use of product if any bleeding or softening is observed.APPLICATION:1. Dilute accordingly with cool to warm water. For normal stripping dilute 13 oz./gallon (1:10) of water. For aggressive stripping dilute 26 oz./gallon of water (1:5).2. Apply solution liberally with a mop.3. Allow 4-5 minutes contact time. Be sure to keep surface wet at all times. Agitate with a low-speed rotary machine or automatic scrubber.4. Pick up solution using a wet vacuum or automatic scrubber.5. Allow floor to dry thoroughly. Rinse with Hillyard Nutra-Rinse solution for best results.NOTICE: Floor may become slippery when stripper is present. Pick up solution immediately with wet vac or mop. Damp mop rinse. Apply polish after floor isclean and dry. Stripper vapors or liquid may cause discoloration on uncured, light colored painted surfaces. DO NOT USE ON GLASS.DISPOSAL: Do not dispose of in storm drain. Buyer assumes all risk and liability associated with disposal of this product (original concentration or dilution)in violation of applicable law.CONTAINER DISPOSAL: Triple rinse (or equivalent). Then offer clean, dry container for recycling or reconditioning.

DISCLAIMER OF WARRANTYSeller makes no warranty of any kind, express or implied, except that this product shall be of seller’s standard quality.

HMIS Rating: Health =/3, Flammability = 0, Reactivity = 0

DANGERHARMFUL OR FATAL IF SWALLOWED OR ABSORBED THROUGH SKIN

HARMFUL IF INHALED – MAY CAUSE BURNSCONTAINS: BUTYL CELLOSOLVE (CAS #111-76-2); ETHANOLAMINE (CAS #141-43-5); POTASSIUM HYDROXIDE (CAS #1310-58-3); SODIUM METASILICATE(CAS #6834-92-0); WATER (CAS #7732-18-5); SODIUM XYLENE SULFONATE (CAS #1300-58-3). Corrosive. USE WITH ADEQUATE VENTILATION. Avoidprolonged breathing of vapors or spray mist. Open windows and doors, use exhaust fans or other means to insure fresh air entry duringapplication and drying. Refer to OSHA STANDARD 29 CFR 1910.94 for technical guidelines on keeping air contamination below acceptable exposurelimits. Do not take internally. Do not get in eyes, on skin, or on clothing. Protect eyes and skin when handling concentrate. Keep container closed when not in use. Incase of spillage, absorb and dispose of in accordance with local applicable regulations.PERSONAL PROTECTIVE EQUIPMENT: For eyes use chemical safety goggles; for skin wear impervious rubber gloves, boots, and apronswhere splashing of concentrate is a problem. Wear impervious/slip resistant boots such as Hillyard Stripping Boots while standing in the stripping solution.FIRST AID: Inhalation - Remove person to fresh air. If breathing difficulty persists or occurs later, call a physician. In case of contact, immediately flush eyesor skin with plenty of water for 15 minutes. Get prompt medical attention. Remove and wash all contaminated clothing before reuse. If swallowed, immediately givelarge amounts of water and CALL A PHYSICIAN, hospital emergency room, or poison control center.See Material Safety Data Sheet for additional information.

KEEP OUT OF REACH OF CHILDREN0904

PHYSICAL PROPERTIES:1. Color ........................................................................................ Light amber2. Clarity .................................................................................................. Clear3. Odor .......................................................................................... Mild solvent4. pH of concentrate ...................................................................... 13.5 ± 0.55. Specific gravity, 25°C ......................................................................... 1.0576. Weight per gallon, 25°C ................................................. 8.80 lbs. (4.00 kg.)7. Freezing point ........................................................ Does not freeze at 10°F8. Freeze-thaw stability (3 cycles) ......................................................... Stable9. Heat stability at 126°F ....................................................................... Stable

10. Flash point (TCC) .................................................................. None to 200°F11. Phosphates ......................................................................................... None

12. Soap content ...................................................................................... None13. Butyl cellosolve content ......................................................................... Yes14. Foam properties .................................................................................... Low15. Abrasives ............................................................................................ None16. Wetting ability ............................................................................... Excellent17. Emulsification ................................................................................ Excellent

TEST METHODS:1. ASTM E702. ASTM D8913. ASTM D1475

10. ASTM D56