140cps12420

840 USE 100 00 September 2002

Power Supply Modules

At a Glance

Overview The following chapter describes the Quantum power supplies, including: specifications, LED indicators and descriptions, and wiring diagrams. Where applicable, it includes operating curves and hold-up capacitor timing charts.

What’s in this Chapter?

This chapter contains the following topics:

Topic Page

140CPS11100 AC Power Supply 115/230 Vac 3 A Module 78

140CPS11400 AC Power Supply, 115/230 Vac, 8 A Module 82

140CPS11410 AC Summable Power Supply 115/230 Vac, 8 A 85

140CPS11420 AC Summable Power Supply 115/230 Vac, 11 A 88

140CPS12400 AC Redundant Power Supply, 115/230 Vac 8 A Module 91

140CPS12420 AC Redundant Power Supply, 115/230 Vac 11 A Module 94

140CPS21100 DC Power Supply, 24 Vdc, 3 A Module 97

140CPS21400 DC Summable Power Supply, 24 Vdc, 8 A Module 100

140CPS22400 DC Redundant Power Supply, 24 Vdc, 8 A Module 103

140CPS41400 DC Summable Power Supply, 48 Vdc, 8 A Module 106

140CPS42400 DC Redundant Power Supply, 48 Vdc, 8 A Module 109

140CPS51100 DC Power Supply, 125 Vdc, 3 A Module 113

140CPS52400 DC Standalone/Redundant Power Supply, 125 Vdc, 8 A 116

77

Power Supplies

140CPS11100 AC Power Supply 115/230 Vac 3 A Module

Overview The following provides information on the AC Power Supply, 115/230 Vac, 3 A module.

Power Supply Module

The following figure shows the power supply module components.

Note: When field wiring the power supply module, the maximum wire size that should be used is 1 - 14 AWG or 2 - 16 AWG; the minimum is 20 AWG.

140CPS 111 00PS 115/230

X

Removable Door

Customer Identification Label(Fold label and place it inside door)

Model NumberModule DescriptionColor CodeLED Area

X

XXXXXXXXXXXXXXXXXXXX

XXXXXXXXXXXXXXXXXXXXX

Field WiringConnector Cover

Field WiringConnector

1234567

1234567 AC L

AC N

78 840 USE 100 00 September 2002

Power Supplies

Specifications The following table shows the specifications for the CPS11100 115/230 VAC power supply module.

Specifications

Input Requirements

Input Voltage 100 ... 276 Vac

Input Frequency 47 ... 63 Hz

Input Voltage Total Harmonic Distortion

Less than 10% of the fundamental ms value

Input Current 0.4 A @ 115 Vac. 0.2 A @ 230 Vac

Inrush Current 10 A @ 115 Vac. 20 A @ 230 Vac

VA Rating 50 VA

Input Power Interruption 1/2 cycle @ full load and minimum rated line voltage / frequency. No less than 1 second between interruptions.

Fusing (external) 1.5 A slo-blo recommended (Part # 043502515 or equivalent)

Output to Bus

Voltage 5.1 Vdc

Maximum Current 3 A

Minimum Current 0.3 A

Protection Over Current, Over Voltage

General

Field Wiring Connector (included)

7 point terminal strip (Part # 043506326)

Internal Power Dissipation 2.0 + 3.0 x IOUT = Watts (where IOUT is in Amperes)

Operating Mode Standalone

840 USE 100 00 September 2002 79

Power Supplies

LED Indicator and Description

The following figure shows the CPS11100 LED indicator.

The following table shows the CPS11100 LED description.

Note: For "Closed System" installations, connector 140XTS00 500 must be used (refer to Closed System Installation, p. 853 ).

LED Description

LEDs Color Indication when On

Pwr ok Green Power is supplied to the bus.

Pwr ok

80 840 USE 100 00 September 2002

Power Supplies

Wiring Diagram The following figure shows the CPS11100 wiring diagram.

Note: See Power and Grounding Considerations for AC and DC Powered Systems, p. 832 for power and grounding wiring guidelines and operational information.

Not used

Not used

Not used

Not used

AC L

AC N

1

2

3

4

5

6

7

840 USE 100 00 September 2002 81

Power Supplies

140CPS11400 AC Power Supply, 115/230 Vac, 8 A Module

Overview The following provides information on the AC Power Supply, 115/230 Vac, 8 A module.

Power Supply Module



140CPS 114 00PS 115/230 VAC

X

Removable Door


Model NumberModule DescriptionColor Code LED Area

X





1234567

1234567

115Vac

115Vac

AC L

AC N

82 840 USE 100 00 September 2002

Power Supplies


Specifications

Input Requirements

Input Voltage 93 ... 138 Vac. 170 ... 276 Vac



Less than 10% of the fundamental ms value



VA Rating 130 VA

Input Power Interruption 1/2 cycle @ full load and minimum-rated line voltage / frequency. No less than 1 second between interruptions.

Fusing (external) 2.0 A slo-blo recommended (Part # 57-0089-000 or equivalent)

Output to Bus

Voltage 5.1 Vdc

Maximum Current 8 A @ 60° C (See the operating curve below)

Minimum Current None required


General



Internal Power Dissipation 6.0 + 1.5 x Iout = Watts (where Iout is in Amperes)


840 USE 100 00 September 2002 83

Power Supplies




Wiring Diagram and Operating Curve

The following figures show the CPS11400 Wiring Diagram (left) and operating curve (right).

LED Description



Pwr ok


Internally connected.Do not connect any external wiring to these points.

AC L

AC N

1

2

3

4

5

6

7

}Install jumper for 115 VAC operation only

Ambient Temperature (C)

Out

put t

o B

us C

urre

ntT

(A

)

40 6050 5545

1210

8

64

2

84 840 USE 100 00 September 2002

Power Supplies

140CPS11410 AC Summable Power Supply 115/230 Vac, 8 A

Overview The following provides information on the AC power supply, 115/230 Vac, 8 A module.

Power Supply Module

The following figure shows the power supply module and its components.

140CPS 114 10PS 115/230

X

Removable Door



X





1234567

1234567

115 VAC

115VAC

AC L

AC N

840 USE 100 00 September 2002 85

Power Supplies


Specifications

Input Requirements




Less than 10% of the fundamental rms value



VA Rating 130 VA



Output to Bus

Voltage 5.1 Vdc

Maximum Current 8 A @ 60° C



General



Internal Power Dissipation 6.0 + 1.5 x IOUT = Watts (where IOUT is in Amperes)

Operating Mode Standalone / Summable

86 840 USE 100 00 September 2002

Power Supplies




Wiring Diagram The following figures shows the 140CPS11410.

LED Descripton



Pwr ok

Note: See (See Power and Grounding Considerations for AC and DC Powered Systems, p. 832) for power and grounding wiring guidelines and operational information.


AC L

AC N

1

2

3

4

5

6

7


840 USE 100 00 September 2002 87

Power Supplies

140CPS11420 AC Summable Power Supply 115/230 Vac, 11 A

Overview The following provides information on the AC power supply, 115/230 Vac, 11 A module.

Power Supply Module

The following figure shows the power supply module and its components.

140CPS 114 20PS 115/230

X

Removable Door



X





1234567

1234567

Power loss alarm115 VAC

115 VAC

AC L

AC N

88 840 USE 100 00 September 2002

Power Supplies


Specifications

Input Requirements

Input Voltage 93 ... 138 Vac.170 ... 264 Vac




Input Current 1.2 A @ 115 Vac.0.7 A @ 230 Vac

Inrush Current @ 25° C (first power up)

≤ 20 A @ 115 Vac.≤ 25 A @ 230 Vac

VA Rating 160 VA @ 11 A



Output to Bus

Voltage 5.1 Vdc

Maximum Current Stand alone configuration: 11 A @ 60° CSummable configuration (Two 140CPS11420): 20 A @ 60° C (Total load capacity)Summable configuration (One 140CPS11420 and one 140CPS11410): 16A @ 60° C (Total load capacity)



General



Internal Power Dissipation Less than 12 W at full load


840 USE 100 00 September 2002 89

Power Supplies




Wiring Diagram The following figures shows the CPS11420.

LED Description



Pwr ok

Note: A normally closed relay contact rated at 220 Vac, 6A / 30 Vdc, 5A is available on terminals 1 and 2 of the power terminal strip. This contact set may be used to signal input power OFF. The relay will de-energize when input power drops below 8 Vdc.


AC L

AC N

1

2

3

4

5

6

7

Install jumper for 115 VAC operation only

Power loss alarm

90 840 USE 100 00 September 2002

Power Supplies

140CPS12400 AC Redundant Power Supply, 115/230 Vac 8 A Module

Overview The following provides information on the AC redundant power supply, 115/230 Vac, 8 A module.

Power Supply Module



140CPS 124 00115/230 VAC

X

Removable Door



X





1234567

1234567

115 VAC

115 VAC

AC L

AC N

840 USE 100 00 September 2002 91

Power Supplies

Specifications The following table shows the specifications for the CPS12400 PS 115/230 VAC power supply module.

Specifications

Input Requirements







VA Rating 130 VA



Output to Bus

Voltage 5.1 Vdc




General



Internal Power Dissipation 6.0 + 1.5 x Iout = Watts (where Iout is in Amperes)

Operating Mode Standalone / Redundant

92 840 USE 100 00 September 2002

Power Supplies




Wiring Diagram The following figure shows the 140CPS12400 wiring diagram.

LED Description



Pwr ok



AC L

AC N

1

2

3

4

5

6

7


840 USE 100 00 September 2002 93

Power Supplies

140CPS12420 AC Redundant Power Supply, 115/230 Vac 11 A Module

Overview The following provides information on the AC redundant power supply, 115/230 Vac, 11 A module.

Power Supply Module



140CPS 124 20 PS 115/230

X

Removable Door



X





1234567

1234567

Power loss alarm115 VAC

115 VAC

AC L

AC N

94 840 USE 100 00 September 2002

Power Supplies

Specifications The following table shows the specifications for the CPS12420 PS 115/230 VAC power supply module.

Specifications

Input Requirements

Input Voltage 93 ... 138 Vac.170 ... 263 Vac




Input Current 1.2 A @ 115 Vac 0.7 A @ 230 Vac

Inrush Current ≤ 20 A @ 115 Vac @ 25° C first power up ≤ 25 A @ 230 Vac

VA Rating 160 VA @ 11 A



Output to Bus

Voltage 5.1 Vdc

Maximum Current Standalone configuration: 11 A @ 60° CRedundant configuration (two 140CPS12420): 10 A @ 60° C (total load capacity)Redundant configuration (one 140CPS12420 and one 140CPS12400): 8A @ 60° C (total load capacityRedundant configuration (one 140CPS12420 and one 140CPS22400): 8 A @ 60° C (total load capacity)Redundant configuration (one 140CPS12420 and one 140CPS42400): 8 A @ 60° C (total load capacity)



General



Internal Power Dissipation Less than 12 W at full load


840 USE 100 00 September 2002 95

Power Supplies





LED Description



Pwr ok

Note: A normally closed relay contact rated at 220 Vac, 6A / 30 Vdc, 5A is available on terminals 1 and 2 of the power terminal strip. This contact set may be used to signal input power OFF. The relay will de-energize when input power drops below 8 Vdc.


AC L

AC N

1

2

3

4

5

6

7

Install jumper for 115 VAC operation only

Power loss alarm

96 840 USE 100 00 September 2002

Power Supplies

140CPS21100 DC Power Supply, 24 Vdc, 3 A Module

Overview The following provides information on the DC power supply, 24 Vdc, 3 A module.

Power Supply Module



140CPS 211 00PS 24 VDC

X

Removable Door



X





1234567

1234567

24Vdc-

24Vdc+

840 USE 100 00 September 2002 97

Power Supplies

Specifications The following table shows the specifications for the CPS21100 PS 24 VDC power supply module.




Specifications

Input Requirements

Input Voltage 20 ... 30 Vdc

Input Current 1.6 A

Inrush Current 30 A

Input Power Interruption 1.0 ms max @ 20 V. 20.0 ms max @ 24 V


Output to Bus

Voltage 5.1 Vdc

Maximum Current 3 A



General

Field Wiring Connector (included) 7 point terminal strip (Part # 043503328)

Internal Power Dissipation 2.0 + 3 x Iout = Watts (where Iout is in Amperes)


LED Description



Pwr ok

98 840 USE 100 00 September 2002

Power Supplies

Wiring Diagram The following figure shows the 140CPS21100 wiring diagram.


1

2

3

4

5

6

7

Not used

Not used

-24 Vdc (Common)

+24 Vdc

Not used

Not used

840 USE 100 00 September 2002 99

Power Supplies

140CPS21400 DC Summable Power Supply, 24 Vdc, 8 A Module

Overview The following provides information on the DC summable power supply, 24 Vdc, 8 A module.

Power Supply Module



140CPS 214 00PS 24 VDC

X

Removable Door



X





1234567

1234567

AlarmRelay24Vdc-

24Vdc+

+

-cap

100 840 USE 100 00 September 2002

Power Supplies

Specifications The following table shows the specifications for the 140CPS21400 PS 24 Vdc power supply module.




Specifications

Input Requirements


Input Current 3.8 A max

Inrush Current 25 A @ 24 Vdc. 14 A @ 20 Vdc

Input Ripple 2.4 Vdc max, 94 ... 189 Hz

Input Power Interruption 1 ms max @ 24 Vdc (see the hold-up capacitor timing chart)


Output to Bus

Voltage 5.1 Vdc

Maximum Current 8 A



General

Field Wiring Connector 7 point terminal strip (Part # 043503328)

Internal Power Dissipation 6.0 + 1.8 x IOUT = Watts (where IOUT is in Amperes


LED Description



Pwr ok

840 USE 100 00 September 2002 101

Power Supplies

Wiring Diagram and Timing Chart

The following figures show the CPS214 wiring diagram (left) and the hold-up capacitor timing chart (right).

Note: 1. A normally closed relay contact rated at 220 Vac, 6A / 30 Vdc, 5A is available

on terminals 1 and 2 of the power terminal strip. This contact set may be used to signal input power OFF. The relay will de-energize when input power drops below 8 Vdc.

2. Tolerance to input interruptions may be increased by adding a ≥ 50 Vdc electrolytic capacitor between 5 and 6 of the power terminal strip. Refer to the hold-up capacitor timing chart for capacitor values.


1

2

3

4

5

6

7

} Power LossAlarm

-24 Vdc (Common)

+24 Vdc

+

- Capacitor(Optional)

Capacitor Size (millifarads)

Times/ms

Input Voltage

Capacitor Size(millifarads)

100

90

80

70

60

50

40

30

20

10

020 21 22 23 24 25 26 27 28 29 30

22

105.84.72.210

4768100

102 840 USE 100 00 September 2002

Power Supplies

140CPS22400 DC Redundant Power Supply, 24 Vdc, 8 A Module

Overview The following provides information on the DC Redundant Power Supply, 24 Vdc, 8 A module.

Power Supply Module



140CPS 224 00PS 24 VDC

X

Removable Door



X





1234567

1234567

AlarmRelay24Vdc-

24Vdc+

+

-cap

840 USE 100 00 September 2002 103

Power Supplies

Specifications The following table shows the specifications for the 24 Vdc, 8 A DC redundant power supply.




Specifications

Input Requirements


Input Current 3.8 A max

Inrush Current 25 A @ 24 Vdc. 14 A @ 20 Vdc

Input Ripple 2.4 Vdc max, 94 ... 189 Hz

Input Power Interruption 1 ms max @ 24 Vdc


Output to Bus

Voltage 5.1 Vdc

Current 8 A


General

Surge Withstand 2.3 x Maximum Rated Input Voltage for 1.3 ms


Internal Power Dissipation 6.0 + 1.8 x Iout = Watts (where Iout is in Amperes


LED Description



Pwr ok

104 840 USE 100 00 September 2002

Power Supplies

Wiring Diagram and Timing Chart

The following figures show the 140CPS22400 wiring diagram (left) and the 140CPS22400 hold-up capacitor timing chart (right).

Note: 1. A normally closed relay contact rated at 220 Vac, 6A / 30 Vdc, 5A is available

on terminals 1 and 2 of the power terminal strip. This contact set may be used to signal input power OFF, or a power supply failure. The relay will de-energize when input power drops below 8 Vdc.

2. Tolerance to input interruptions may be increased by adding a ≥ 50 Vdc electrolytic capacitor between 5 and 6 of the power terminal strip. Refer to the hold-up capacitor timing chart (above) for capacitor values.


1

2

3

4

5

6

7

} Power LossAlarm

-24 Vdc (Common)

+24 Vdc

+


Capacitor Size (millifarads)

Times/ms

Input Voltage

Capacitor Size(millifarads)

100

90

80

70

60

50

40

30

20

10

020 21 22 23 24 25 26 27 28 29 30

22

105.84.72.210

4768100

840 USE 100 00 September 2002 105

Power Supplies

140CPS41400 DC Summable Power Supply, 48 Vdc, 8 A Module

Overview The following provides information on the DC summable power supply, 48 Vdc, 8 A module.

Power Supply Module



140CPS 414 00PS 48 VDC

X

Removable Door



X





1234567

1234567

AlarmRelay48Vdc-

48Vdc+

+

-cap

106 840 USE 100 00 September 2002

Power Supplies

Specifications The following table shows the specifications for the CPS41400, 48 VDC power supply module.




Specifications

Input Requirements


Input Current 1.2 A @ 48 Vdc

Inrush Current 25 A @ 40 Vdc

Input Power Interruption 13 ms @ 48 Vdc

Fusing (external) 2.0 A medium time-lag recommended (Part # 57-0089-000 or equivalent)

Output to Bus

Voltage 5.1 Vdc

Current 8 A (see operating curve)


General


Internal Power Dissipation 15.6 W @ 8 A


LED Description



Pwr ok

840 USE 100 00 September 2002 107

Power Supplies


Operating Curve and Timing Chart

The following figures show the CPS41400 operating curve (left) and the hold-up capacitor timing chart (right).

Note: A normally closed relay contact rated at 220 Vac, 6A / 30 Vdc, 5A is available on terminals 1 and 2 of the power terminal strip. This contact set may be used to signal input power OFF, or a power supply failure.


}1

2

3

4

5

6

7

Power LossAlarm

-48 ... -60 Vdc (Common)

+48 ... +60 Vdc

+


Note: Tolerance to input interruptions may be increased by adding a ≥ 80 Vdc electrolytic capacitor between 5 and 6 of the power terminal strip. Refer to the hold-up capacitor timing chart (above) for capacitor values.

Tim

e/m

s

100

90

80

70

60

50

40

30

20

10

040 45 50 55 60 65 70

2.2

1

0

47 22 10 6.8 4.7


Out

put t

o B

us C

urre

ntT

(A

)

40 6050 5545

12

10

8

6

4

2

108 840 USE 100 00 September 2002

Power Supplies

140CPS42400 DC Redundant Power Supply, 48 Vdc, 8 A Module

Overview The following provides information on the DC redundant power supply, 48 Vdc, 8 A module.

Power Supply Module



Note: Tolerance to input interruptions may be increased by adding an 80 Vdc electrolytic capacitor between 5 and 6 of the power terminal strip. Refer to the hold-up capacitor timing chart (above) for capacitor values.

140CPS 424 00PS 48 VDC

X

Removable Door



X





1234567

1234567

AlarmRelay48Vdc-

48Vdc+

+

-cap

840 USE 100 00 September 2002 109

Power Supplies

Specifications The following table shows the specifications for the 140CPS42400 PS 48 VDC RED power supply module.




Specifications

Input Requirements




Input Power Interruption 13 ms @ 48 Vdc

Fusing (external) 2.0 A medium time-lag recommended (Part # 57-0089-000 or equivalent)

Output to Bus

Voltage 5.1 Vdc

Current 8 A (see operating curve)


General


Internal Power Dissipation 17.2 W @ 8 A


LED Description



Pwr ok

110 840 USE 100 00 September 2002

Power Supplies



Note: A normally closed relay contact rated at 220 Vac, 6A / 30 Vdc, 5A is available on terminals 1 and 2 of the power terminal strip. This contact set may be used to signal input power OFF, or a power supply failure.

}1

2

3

4

5

6

7

Power LossAlarm

-48 ... -60 Vdc (Common)

+48 ... +60 Vdc

+


840 USE 100 00 September 2002 111

Power Supplies

Operating Curve and Timing Chart

The following figures show the CPS42400 operating curve (left) and the hold-up capacitor timing chart (right).

Note: Tolerance to input interruptions may be increased by adding a ≥ 80 Vdc electrolytic capacitor between 5 and 6 of the power terminal strip. Refer to the hold-up capacitor timing chart (above) for capacitor values.

Capacitor size/mF

Input Voltage

Tim

e/m

s

100

90

80

70

60

50

40

30

20

10

040 45 50 55 60 65 70

2.2

1

0

47 22 10 6.8 4.7


Out

put t

o B

us C

urre

ntT

(A

)

40 6050 5545

12

10

8

6

4

2

112 840 USE 100 00 September 2002

Power Supplies

140CPS51100 DC Power Supply, 125 Vdc, 3 A Module

Overview The following provides information on the DC power supply, 125 Vdc, 3 A module.

Power Supply Module



140CPS 511 00PS 125 VDC

X

Removable Door



X





1234567

1234567

125Vdc+

125Vdc-

840 USE 100 00 September 2002 113

Power Supplies

Specifications The following table shows the specifications for the CPS51100 125 Vdc power supply module.




Specifications

Input Requirements

Input Voltage 100 ... 150 Vdc including ripple

Input Current 0.4 A

Inrush Current 10 A

Input Power Interruption 1.0 ms max


Output to Bus

Voltage 5.1 Vdc

Maximum Current 3 A



General



Internal Power Dissipation 2.0 + 3 x Iout = Watts (where Iout is in Amperes)


LED Description



Pwr ok

114 840 USE 100 00 September 2002

Power Supplies



Not used

Not used

Not used

Not used

125 VDC +

125 VDC - (Common)

1

2

3

4

5

6

7

840 USE 100 00 September 2002 115

Power Supplies

140CPS52400 DC Standalone/Redundant Power Supply, 125 Vdc, 8 A

Overview The following provides information on the DC Standalone/Redundant power supply, 125 Vdc, 8 A module.

Power Supply Module



140CPS 524 00PS 125 VDC

X

Removable Door



X





1234567

1234567

125 Vdc+

125 Vdc-

116 840 USE 100 00 September 2002

Power Supplies

Specifications The following table shows the specifications for the CPS52400 125 VDC power supply module.

Specifications

Input Requirements

Input Voltage 100 ... 150 Vdc including ripple



Input Power Interruption 1.0 ms max

Fusing (external) 2 A slo-blo recommended (Part # 57-0089-000 or equivalent)

Output to Bus

Voltage 5.1 Vdc




General



Internal Power Dissipation 6.0 + 1.5 x |OUT = Watts (where |OUT is in Amperes)


840 USE 100 00 September 2002 117

Power Supplies





LED Description



Pwr ok



1

2

3

4

5

6

7

}Not used

Not used

125VDC +

125 VDC - (Common)

118 840 USE 100 00 September 2002

140cps12420

Documents

Transcript of 140cps12420