14.02 Roust-A-Bout Couplings
Transcript of 14.02 Roust-A-Bout Couplings
Style 99 Roust-A-Bout couplings are designed with heavy housings and grips to provide
a strong component for joining plain and beveled end, including Schedule 80 steel pipe
and Victaulic plain end fittings. Roust-A-Bout couplings are not designed for use on plastic
pipe, pipe with brittle linings, cast or ductile iron pipe nor any pipe with a surface hardness
greater than 150 Brinell.
Pipe is secured together by heavy jaws, which are set into the housing. All sizes are
supplied with painted housings and plated nuts and bolts. Galvanized housings are
available.
WARNING
Style 99 Roust-A-Bout couplings must be assembled with nuts tightened to full torque
specifications.
Housing: Ductile iron conforming to ASTM A-536, grade 65-45-12. Ductile iron conforming to ASTM
A-395, grade 65-45-15, is available upon special request.
Housing Coating: Orange enamel.
• Optional: Hot dipped galvanized and others.
Jaws: Carbon steel, case hardened, electroplated, except sizes 1''; 76.1 mm and 139.7 mm, which
utilize stainless steel, Type 416, hardened.
Gasket: (specify choice*)
• Grade “E” EPDM
EPDM (Green color code). Temperature range –30°F to +230°F/–34°C to +110°C.
Recommended for cold and hot water service within the specified temperature range plus a
variety of dilute acids, oil-free air and many chemical services. UL classified in accordance
with ANSI/NSF 61 for cold +86°F/+30°C and hot +180°F/+82°C potable water service. NOT
RECOMMENDED FOR PETROLEUM SERVICES.
• Grade “T” nitrile
Nitrile (Orange color code). Temperature range –20°F to +180°F/–29°C to +82°C.
Recommended for petroleum products, air with oil vapors, vegetable and mineral oils within the
specified temperature range. Not recommended for hot water services over +150°F/+66°C or
for hot dry air over +140°F/+60°C.
* Services listed are General Service Recommendations only. It should be noted that there are
services for which these gaskets are not recommended. Reference should always be made to
the latest Victaulic Gasket Selection Guide for specific gasket service recommendations and for a
listing of services which are not recommended.
Bolts/Nuts/Washers: Heat-treated plated carbon steel, trackhead meeting the physical and chemical
requirements of ASTM A-449 and physical requirements of ASTM A-183. The 6"/150 mm and
larger sizes are supplied with hardened steel washers meeting ASTM F-436 Type 3 (weathering
steel).
MATERIAL SPECIFICATIONS
14.02_1
Roust-A-Bout® CouplingsSTYLE 99
14.02IPS CARBON STEEL PIPE – PLAIN END SYSTEM
JOB/OWNER CONTRACTOR ENGINEER
System No. __________________________ Submitted By ________________________ Spec Sect ____________ Para __________
Location ____________________________ Date ________________________________ Approved ___________________________
Date ________________________________
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_H
Exaggerated for clarity Exaggerated for clarity
1 ½ – 12'' SIZES
1 ½ – 18'' SIZES 1''; 76.1 & 139.7 MM SIZES
14 – 18'' SIZES
SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS
DIMENSIONS
Size
MaxWorkPress.
Max.EndLoad
RequiredBolt
Torque
‡Bolt/Nut
No. – SizeDimensionsInches/mm
Aprx.Weight
NominalSize
Inchesmm
ActualOutside
DiameterInches
mmpsikPa
Lbs. *N
Lb. Ft. **N•m Inches X Y Z
Lbs.kg
1 1.315 600 800 352 – 3⁄8 x 2
2.56 4.25 2.25 1.725 33.7 4130 3560 47.5 65 108 57 0.8
1 ½ 1.900 750 2100 602 – ½ x 2 ½
3.25 5.50 2.88 3.640 48.3 5175 9345 81.4 83 140 73 1.6
2 2.375 750 3300 1502 – 5⁄8 x 3 ¼
3.75 6.75 3.38 5.350 60.3 5175 14685 203.4 95 171 86 2.4
2 ½ 2.875 600 3890 1502 – 5⁄8 x 3 ¼
4.25 7.13 3.38 5.765 73.0 4130 17310 203.4 108 181 86 2.5
76.1 mm3.000 400 2825 95
2 – ½ x 2 ¾ 4.69 6.25 2.75 4.4
76.1 2700 12500 128.8 119 159 70 2.0
3 3.500 600 5770 2002 – ¾ x 4 ¼
5.00 8.50 3.38 8.780 88.9 4130 25676 271.2 127 216 86 3.9
3 ½ 4.000 500 6280 2002 – ¾ x 4 ¼
5.50 9.25 3.63 10.690 101.6 3450 27946 271.2 140 235 92 4.8
4 4.500 450 7155 2002 – ¾ x 4 ¼
6.13 10.00 4.00 12.8100 114.3 3100 31840 271.2 156 254 102 5.8
139.7 mm5.500 250 5940 160
2 – ¾ x 57.80 10.75 3.19 9.0
139.7 1700 26440 217.0 200 260 81 4.1
5 5.563 350 8500 2502 – 7⁄8 x 5
7.25 11.38 4.38 17.3125 141.3 2400 37825 339.0 184 289 111 7.8
6 6.625 300 10340 2502 – 1 x 6 #
8.50 13.38 4.38 23.2150 168.3 2065 46013 339.0 216 340 111 10.5
165.1 mm6.500 300 9955 250
2 – 1 x 6 #8.38 13.25 4.38 22.2
165.1 2065 44300 339.0 213 337 111 10.1
8 8.625 250 14600 2504 – 7⁄8 x 5 #
10.88 14.38 5.00 37.2200 219.1 1700 64970 339.0 276 365 127 16.9
10 10.750 250 22700 3004 – 7⁄8 x 5 #
13.38 16.38 5.00 48.2250 273.0 1700 101015 406.8 340 416 127 21.9
12 12.750 250 31900 3504 – 1 x 6 ½ #
15.50 19.63 5.13 60.0300 323.9 1700 141955 474.6 394 499 130 27.2
14 14.000 200 30800 3508 – 1 x 6 ½ #
16.75 20.75 5.38 89.0350 355.6 1400 137060 474.6 425 527 137 40.4
16 16.000 150 30200 3508 – 1 x 6 ½ #
19.00 22.63 5.38 105.0400 406.4 1000 134390 474.6 483 575 137 47.6
18 18.000 150 38200 3508 – 1 x 6 ½ #
21.00 23.50 5.38 125.0450 457.0 1000 169990 474.6 533 597 137 56.7
* Working Pressure and End Load are total, from all internal and external loads, based on coupling properly assembled, with bolts fully torqued to listed specifications, on plain end or beveled end standard weight (ANSI) steel pipe and Victaulic plain end fittings. Couplings are designed to be used with plain end pipe and Victaulic plain end fittings only.
** Bolt torque ratings shown must be applied at installation.
‡ Metric thread size bolts (plated) are available (color coded) for all coupling sizes upon request. Contact Victaulic for details.
WARNING: Depressurize and drain the piping system before attempting to install, remove, or adjust any Victaulic piping products.
# Supplied with flat washers.
Y Z
X
Y Z
X
ZY
X
1 – 6"/25 – 150 MM SIZES
8 – 12"/200 – 300 MM SIZES
14 – 18"/350 – 450 MM SIZES
14.02_2
Roust-A-Bout® CouplingsSTYLE 99
14.02IPS CARBON STEEL PIPE – PLAIN END SYSTEM
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_H
1 2 3 4 5 6
Size Pipe Req’dBolt
Torque
Max.Joint
WorkingPressure
Max.Permiss.End LoadNominal
Outside SizeInches
mm
ActualOutside
DiameterInches
mm
WallThickness
Inchesmm Sched.
Lb.Ft.N • m
psikPa
Lbs.N
125
1.31533.7
0.17980
3547.5
— —4.55
0.13340
600 8003.38 4130 3560
0.10910
600 8002.77 4130 3560
0.0655
400 5501.65 2750 2450
1 ½ 40
1.90048.3
0.20080
6081.4
750 21005.08 5175 9345
0.14540
750 21003.68 5175 9345
0.10910
600 17002.77 4130 7565
0.0655
400 11001.65 2750 4895
250
2.37560.3
0.21880
150203.4
750 33005.54 5175 14685
0.15440
750 33003.91 5175 14685
0.10910
400 18002.77 2750 8010
0.0655
200 9001.65 1375 4005
2 ½ 65
2.87573.0
0.27680
150203.4
600 38907.01 4130 17310
0.20340
600 38905.16 4130 17310
0.12010
300 19003.05 2065 8455
0.0835
150 10002.11 1035 4450
380
3.50088.9
0.30080
200271.2
600 57707.62 4130 25675
0.21640
600 57705.49 4130 25675
0.12010
225 21603.05 1550 9610
0.0835
125 12002.11 860 5340
Table continued on page 4.
PRESSURE RATINGS AND END LOADS
Carbon Steel Pipe
14.02_3
Roust-A-Bout® CouplingsSTYLE 99
14.02IPS CARBON STEEL PIPE – PLAIN END SYSTEM
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_H
1 2 3 4 5 6
Size PipeReq’dBolt
Torque
Max.Joint
WorkingPressure
Max.Permiss.End LoadNominal
Outside SizeInches
mm
ActualOutside
DiameterInches
mm
WallThickness
Inchesmm Sched.
Lb.Ft.N • m
psikPa
Lbs.N
3 ½ 90
4.000101.6
0.31880
200271.2
500 62808.08 3450 27945
0.22640
500 62805.74 3450 27945
0.12010
200 25003.05 1375 11125
0.0835
100 12502.11 690 5565
4100
4.500114.3
0.33780
200271.2
450 71558.56 3100 31840
0.23740
450 71556.02 3100 31840
0.12010
175 28003.05 1200 12460
0.0835
60 9502.11 415 4230
5125
5.563141.3
0.37580
250339.0
350 85009.53 2410 37825
0.25840
350 85006.55 2410 37825
0.13410
150 36003.40 1035 16020
0.1095
75 18002.77 515 8010
6150
6.625168.3
0.43280
250339.0
300 1034010.97 2065 46015
0.28040
300 103407.11 2065 46015
0.13410
100 35003.40 690 15575
0.1095
75 26002.77 515 11570
165.1 mm6.500165.1
0.250—
250339.0
300 99556.35 2065 44300
0.200—
175 60005.08 1200 26700
0.150—
100 35003.81 690 15575
8200
8.625219.1
0.32240
250339.0
250 146008.18 1725 64970
0.27730
200 117007.04 1375 52065
0.14810
100 60003.76 690 26700
0.1095
50 30002.77 345 13350
Table continued on page 5.
PRESSURE RATINGS AND END LOADS
Carbon Steel Pipe
14.02_4
Roust-A-Bout® CouplingsSTYLE 99
14.02IPS CARBON STEEL PIPE – PLAIN END SYSTEM
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_H
1 2 3 4 5 6
Size PipeReq’dBolt
Torque
Max.Joint
WorkingPressure
Max.Permiss.End LoadNominal
Outside SizeInches
mm
ActualOutside
DiameterInches
mm
WallThickness
Inchesmm Sched.
Lb.Ft.N • m
psikPa
Lbs.N
10250
10.750273.0
0.36540
300406.8
250 227009.27 1725 101015
0.30730
175 159007.80 1200 70755
0.16510
75 68004.19 515 30260
0.1345
50 45003.40 345 20025
12300
12.750323.9
0.375STD
350474.6
250 319009.53 1725 141955
0.33030
150 191008.38 1035 84995
0.18010
100 127004.57 690 56515
0.1655
75 95004.19 515 42275
14 14.000 0.375STD
350 200 30800350 355.6 9.53 474.6 1375 137060
16 16.000 0.375STD
350 150 30200400 406.4 9.53 474.6 1035 134390
COLUMN 1: Victaulic couplings are identified by nominal pipe size.
COLUMN 2: Nominal pipe wall thickness.
COLUMN 3: Pipe wall thickness schedule as established in ANSI Standard B36, 10-70.
COLUMN 4: Bolt torque required for installing Victaulic plain end couplings to achieve pressure ratings listed in Column 5 and Permissible Maximum End Loads listed in Column 6.
TORQUE RATINGS MUST BE APPLIED AT INSTALLATION.
COLUMN 5: Maximum line pressure, including surge, to which a joint should be subjected, based on couplings assembled to full torque specifications on plain end or beveled end standard weight steel pipe and/or Victaulic plain end fittings. Working pressure ratings are based on pipe prepared in accordance with Victaulic specifications.
COLUMN 6: Maximum end load from all internal and/or external forces to which the joint should be subjected based on couplings assembled to full torque specifications.
NOTE: Roust-A-Bout couplings, when sufficiently pressurized, will allow pipe to separate slightly as grips set into pipe. For properly assembled and torqued couplings, this separation should not exceed ¼ ''/6.4 mm. This should be considered for installations in tightly confined areas. Style 99 couplings are not designed to provide linear or angular movement.
ROUST-A-BOUT STYLE 99 COUPLINGS ARE DESIGNED FOR USE WITH PLAIN END OR BEVELED END PIPE AND VICTAULIC PLAIN END FITTINGS ONLY.
PRESSURE RATINGS AND END LOADS
Carbon Steel Pipe
14.02_5
Roust-A-Bout® CouplingsSTYLE 99
14.02IPS CARBON STEEL PIPE – PLAIN END SYSTEM
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_H
1 2 3 4 5 6
Size Pipe Req’dBolt
Torque
Max.Joint
WorkingPressure
Max.Permiss.End LoadNominal
SizeInches
mm
ActualOutside
DiameterInches
mm
WallThickness
Inchesmm Sched.
Lb.Ft.N • m
psikPa
Lbs.N
133.4
1.31533.7
0.13340
35 600 8003.38 47.5 4130 3560
0.10910
35 400 5502.77 47.5 2750 2450
0.0655
35 250 3501.65 47.5 1725 1555
1 ½ 48.3
1.90048.3
0.14540
60 500 1.4003.56 81.4 3450 6230
0.10910
60 400 1.1002.77 81.4 2750 4895
0.0655 N/R N/R N/R
1.65
260.3
2.37560.3
0.15440
150 500 2.2003.91 203.4 3450 9790
0.10910
150 400 1.8002.77 203.4 2750 8010
0.0655 N/R N/R N/R
1.65
2 ½ 73.0
2.87573.0
0.20340
150 400 2.5005.16 203.4 2750 11125
0.12010
150 250 1.5005.16 203.4 1725 6675
0.0835 N/R N/R N/R
2.11
388.9
3.50088.9
0.21640
200 400 3.8005.49 271.2 2750 16910
0.12010
200 200 1.9003.05 271.2 1375 8455
0.0835 N/R N/R N/R
2.11
3 ½ 101.6
4.000101.6
0.22640
200 300 3.7005.74 271.2 2065 16465
0.12010
200 150 1.9003.05 271.2 1035 8455
0.0835 N/R N/R N/R
2.11
4114.3
4.500114.3
0.23740
200 250 3.9006.02 271.2 1725 17355
0.12010
200 80 1.3003.05 271.2 550 5785
0.0835 N/R N/R N/R
2.11
5141.3
5.563141.3
0.25840
250 200 4.8006.55 339.0 1375 21360
0.13410
250 75 1.8003.40 339.0 510 8010
0.1095 N/R N/R N/R
2.77
Table continued on page 7.
PRESSURE RATINGS AND END LOADS
Stainless Steel Pipe
14.02_6
Roust-A-Bout® CouplingsSTYLE 99
14.02IPS CARBON STEEL PIPE – PLAIN END SYSTEM
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_H
1 2 3 4 5 6
Size Pipe Req’dBolt
Torque
Max.Joint
WorkingPressure
Max.Permiss.End LoadNominal
SizeInches
mm
ActualOutside
DiameterInches
mm
WallThickness
Inchesmm Sched.
Lb.Ft.N • m
psikPa
Lbs.N
6168.3
6.625168.3
0.28040
250 200 6.8007.11 339.0 1375 30260
0.13410
250 75 2.6003.40 339.0 515 11570
0.1095 N/R N/R N/R
2.77
165.1 mm6.500165.1
0.28040
250 200 6.8007.11 339.0 1375 30260
0.13410
250 75 2.6003.40 339.0 515 11570
0.1095 N/R N/R N/R
2.77
8219.1
8.625219.1
0.32240
250 200 11.0008.18 339.0 1375 48950
0.14810
250 75 4.4003.76 339.0 515 19580
0.1095
250 25 1.4602.77 339.0 170 6495
10273.0
10.750273.0
0.36540
300 100 9.0009.27 406.8 690 40050
0.16510
300 50 4.5004.19 406.8 345 20025
0.1345
300 25 2.2503.40 406.8 170 10010
12323.9
12.750323.9
0.40640
350 100 12.75010.31 474.6 690 56735
0.18010
350 50 6.4004.67 474.6 345 28480
0.1565
350 25 3.2003.96 474.6 170 14240
NR = Not recommended
+ Contact Victaulic for details.
COLUMN 1: Victaulic couplings are identified by nominal pipe size.
COLUMN 2: Nominal pipe wall thickness.
COLUMN 3: Pipe wall thickness schedule as established in ANSI Standard B36, 10-70.
COLUMN 4: Bolt torque required for installing Victaulic plain end couplings to achieve pressure ratings listed in Column 5 and Permissible Maximum End Loads listed in Column 6.
TORQUE RATINGS MUST BE APPLIED AT INSTALLATION.
COLUMN 5: Maximum line pressure, including surge, to which a joint should be subjected, based on couplings assembled to full torque specifications on plain end or beveled end standard weight steel pipe and/or Victaulic plain end fittings. Working pressure ratings are based on pipe prepared in accordance with Victaulic specifications.
COLUMN 6: Maximum end load from all internal and/or external forces to which the joint should be subjected based on couplings assembled to full torque specifications.
NOTE: Roust-A-Bout couplings, when sufficiently pressurized, will allow pipe to separate slightly as grips set into pipe. For properly assembled and torqued couplings, this separation should not exceed ¼ ''/6.4 mm). This should be considered for installations in tightly confined areas. Style 99 couplings are not designed to provide linear or angular movement.
ROUST-A-BOUT STYLE 99 COUPLINGS ARE DESIGNED FOR USE WITH PLAIN END OR BEVELED END PIPE AND VICTAULIC PLAIN END FITTINGS ONLY.
PRESSURE RATINGS AND END LOADS
Stainless Steel Pipe
14.02_7
Roust-A-Bout® CouplingsSTYLE 99
14.02IPS CARBON STEEL PIPE – PLAIN END SYSTEM
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_H
1 2 3 4 5 6
Size PipeReq’dBolt
Torque
Max.Joint
WorkingPressure
Max.Permiss.End LoadNominal
SizeInches
mm
ActualOutside
DiameterInches
mm
WallThickness
Inchesmm Sched.
Lb.Ft.N • m
psikPa
Lbs.N
125
1.31533.7
0.17980 N/R N/R N/R
4.55
0.13340
35 600 8003.38 47.5 4130 3560
0.10910
35 300 4002.77 47.5 2065 1780
0.0655
35 100 1351.65 47.5 690 601
1 ½ 40
1.90048.3
0.20080
60 500 14005.08 81.4 3450 6230
0.14540
60 400 11003.56 81.4 2760 4895
0.10910
60 300 8252.77 81.4 2065 3671
0.0655 N/R N/R N/R
1.65
250
2.37560.3
0.21880
150 400 18005.54 203.4 2760 8010
0.15440
150 300 13003.91 203.4 2065 5785
0.10910
150 200 9002.77 203.4 1380 4005
0.0655 N/R N/R N/R
1.65
2 ½ 65
2.87573.0
0.27680
150 350 22007.01 203.4 2415 9790
0.20340
150 275 17255.16 203.4 1895 7676
0.12010
150 150 10005.16 203.4 1035 4450
0.0835 N/R N/R N/R
2.11
380
3.50088.9
0.30080
200 300 28807.62 271.2 2065 12816
0.21640
200 200 19205.49 271.2 1380 8544
0.12010
200 100 9603.05 271.2 690 4272
0.0835 N/R N/R N/R
2.11
Table continued on page 9.
PRESSURE RATINGS AND END LOADS
Aluminum Pipe*
14.02_8
Roust-A-Bout® CouplingsSTYLE 99
14.02IPS CARBON STEEL PIPE – PLAIN END SYSTEM
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_H
1 2 3 4 5 6
Size PipeReq’dBolt
Torque
Max.Joint
WorkingPressure
Max.Permiss.End LoadNominal
SizeInches
mm
ActualOutside
DiameterInches
mm
WallThickness
Inchesmm Sched.
Lb.Ft.N • m
psikPa
Lbs.N
3 ½ 90
4.000101.6
0.31880
200 250 31008.08 271.2 1725 13795
0.22640
200 200 25005.74 271.2 1380 11125
0.12010
200 100 12503.05 271.2 690 5563
0.0835 N/R N/R N/R
2.11
4100
4.500114.3
0.33780
200 200 32008.56 271.2 1380 14240
0.23740
200 150 24006.02 271.2 1035 10680
0.12010
200 50 8003.05 271.2 345 3560
0.0835 N/R N/R N/R
2.11
5125
5.563141.3
0.37580
250 150 36009.53 339.0 1035 16020
0.25840
250 100 24006.55 339.0 690 10680
0.13410
250 50 12003.40 339.0 345 5340
0.1095 N/R N/R N/R
2.77
6150
6.625168.3
0.43280
250 150 520010.97 339.0 1035 23140
0.28040
250 100 35007.11 339.0 690 15575
0.13410
250 50 17503.40 339.0 345 7788
0.1095
250 35 12252.77 339.0 240 5451
8200
8.625219.1
0.32240
250 150 90008.18 339.0 1035 40050
0.27730
250 100 60007.04 339.0 690 26700
0.25020
250 75 45006.35 339.0 515 20025
0.14810
250 50 30003.76 339.0 345 13350
Table continued on page 10.
PRESSURE RATINGS AND END LOADS
Aluminum Pipe*
14.02_9
Roust-A-Bout® CouplingsSTYLE 99
14.02IPS CARBON STEEL PIPE – PLAIN END SYSTEM
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_H
1 2 3 4 5 6
Size PipeReq’dBolt
Torque
Max.Joint
WorkingPressure
Max.Permiss.End LoadNominal
SizeInches
mm
ActualOutside
DiameterInches
mm
WallThickness
Inchesmm Sched.
Lb.Ft.N • m
psikPa
Lbs.N
10250
10.750273.0
0.35640
300 100 90009.27 406.8 690 40050
0.30730
300 75 63007.80 406.8 515 28035
0.25020
300 50 45006.35 406.8 345 20025
0.16510
300 25 22504.19 406.8 172 10013
12300
12.750323.9
0.40640
300 100 1280010.31 406.8 690 56960
0.33030
300 75 95008.38 406.8 515 42275
0.25020
300 50 60006.35 406.8 345 26700
0.18010
300 25 31504.67 406.8 172 14018
* Aluminum Pipe – Alloy 6063-T6 or 6061-T6 in Schedule 80 and 40; Alloy 6063-T6 in Schedule 30, 20, 10 and 5.
NR = Not recommended
COLUMN 1: Victaulic couplings are identified by nominal pipe size.
COLUMN 2: Nominal pipe wall thickness.
COLUMN 3: Pipe wall thickness schedule as established in ANSI Standard B36, 10-70.
COLUMN 4: Bolt torque required for installing Victaulic plain end couplings to achieve pressure ratings listed in Column 5 and Permissible Maximum End Loads listed in Column 6.
TORQUE RATINGS MUST BE APPLIED AT INSTALLATION.
COLUMN 5: Maximum line pressure, including surge, to which a joint should be subjected, based on couplings assembled to full torque specifications on plain end or beveled end standard weight steel pipe and/or Victaulic plain end fittings. Working pressure ratings are based on pipe prepared in accordance with Victaulic specifications.
COLUMN 6: Maximum end load from all internal and/or external forces to which the joint should be subjected based on couplings assembled to full torque specifications.
NOTE: Roust-A-Bout couplings, when sufficiently pressurized, will allow pipe to separate slightly as grips set into pipe. For properly assembled and torqued couplings, this separation should not exceed ¼ ''/6.4 mm. This should be considered for installations in tightly confined areas. Style 99 couplings are not designed to provide linear or angular movement.
ROUST-A-BOUT STYLE 99 COUPLINGS ARE DESIGNED FOR USE WITH PLAIN END OR BEVELED END PIPE AND VICTAULIC PLAIN END FITTINGS ONLY.
PRESSURE RATINGS AND END LOADS
Aluminum Pipe*
14.02_10
Roust-A-Bout® CouplingsSTYLE 99
14.02IPS CARBON STEEL PIPE – PLAIN END SYSTEM
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_H
WARRANTY Refer to the Warranty section of the current Price List or contact Victaulic for details.
This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be
installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the
right to change product specifications, designs and standard equipment without notice and without
incurring obligations.
NOTE
Reference should always be made to the I-100 Victaulic Field Installation Handbook for the product
you are installing. Handbooks are included with each shipment of Victaulic products for complete
installation and assembly data, and are available in PDF format on our website at www.victaulic.com.
INSTALLATION
14.02_11
Roust-A-Bout® CouplingsSTYLE 99
14.02IPS CARBON STEEL PIPE – PLAIN END SYSTEM
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_H
WCAS-6UPKCK
14.02
Roust-A-Bout® CouplingsSTYLE 99
IPS CARBON STEEL PIPE – PLAIN END SYSTEM
For complete contact information, visit www.victaulic.com
14.02 1671 REV H UPDATED 3/2007
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
14.02