1/3 SS 402 Bell 212 UH-1N S.A. - Eduard
Transcript of 1/3 SS 402 Bell 212 UH-1N S.A. - Eduard
![Page 1: 1/3 SS 402 Bell 212 UH-1N S.A. - Eduard](https://reader031.fdocuments.us/reader031/viewer/2022012512/618b7a1339908e7e6c4f7038/html5/thumbnails/1.jpg)
1/72 scale detail set for REVELL •sada detailù pro model 1/72 REVELL
Bell 212 UH-1N S.A.
SS402
eduard
REMOVEODSTRANIT
OPTIONVOLBA?REPLACENAHRADIT
BENDOHNOUT
GRINDOBROUSIT
SYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽ
DRILL HOLEVRTAT OTVOR
APPLY EXPRESS MASK AND PAINT BEFORE GLUINGPOUŽÍT EXPRESS MASK NABARVIT PØED SLEPENÍM
1/3 SS 402
ORIGINAL KIT PARTSPÙVODNÍ DÍLY STAVEBNICE
PHOTO-ETCHED PARTSLEPTANÉ DÍLY
PARTS TO BE REMOVEDDÍLY K ODSTRANÌNÍ
FILLTMELIT
1513
9
7
13
1
12
2pcs5
1
2
16
16
5
6
17
2
3
4
2, 3, 4
3
5+6+17
2, 3, 4
1
![Page 2: 1/3 SS 402 Bell 212 UH-1N S.A. - Eduard](https://reader031.fdocuments.us/reader031/viewer/2022012512/618b7a1339908e7e6c4f7038/html5/thumbnails/2.jpg)
2/3 SS 402
19
7
8
19
1
11
10
11
10
5+6+17
1
24
24
3
414
152pcs
4 14
16
17
60 61
2218 20
37 36
23
© EDUARD M.A. 2011 Made in Czech Republicwww.eduard.com
21
25
47
![Page 3: 1/3 SS 402 Bell 212 UH-1N S.A. - Eduard](https://reader031.fdocuments.us/reader031/viewer/2022012512/618b7a1339908e7e6c4f7038/html5/thumbnails/3.jpg)
2. Do not inadvertently place etched componets on an unwanted surface. Attempts to remove will result in damage to your part.
2. Nepokládejte samolepící díly na volné plochy. Pokud je omylem pøilepíte, pøi pokusu o odlepení dojde k poškození dílu.
3. Do not touch the adhesive areas of the etched components.
3. Nesahejte na èásti dílù, na kterých je naneseno lepidlo.1. Separate the etched components from their frames on the protective paper. Removal from the paper is done only after separation of the parts from the frames.
1.Samolepící díly oddìlujte od rámeèku na podkladovém papíøe. Po oddìlení je sejmìte z krycího papíru.
4. Hold the parts by the edges, or at areas free of adhesive.
4. Samolepící díly berte za hrany nebo za èásti, na kterých není nanesené lepidlo.
5. Lightly place the component in the desired location and position. Adjust as required. The component will by permanently affixed when pressed onto its intended location, its location can be adjusted.
5. Díl lehce položte do pozice, ve které má být nalepen. Upravte pøesnou pozici a pøimáèknìte. Díl dokonale pøilne až po pøimáèknutí, pøed pøimáèknutím lze dílem opatrnì manipulovat.
PARTS WITH GLUE DÍLY OPATØENÉ LEPIDLEM
3/3 SS 402