12X18 U S T O M E R S ATIS RATE FACTIO C N SHED PLAN€¦ · walls should be 11 feet and 5 1/2...

9
12X18 LEAN TO SHED PLAN FREE STREAMLINED VERSION Supported & Recommended by our Friends & Partners: 2018 RATE C U S T O M E R S A T I S F A C T I O N C U S T O M E R S A T I S F A C T I O N 98,6% Copyright © 2018 All Rights Reserved. Use of this PDF file constitutes acceptance of the 3DSHEDPLANS.COM User Terms and Privacy Policy. Page 1

Transcript of 12X18 U S T O M E R S ATIS RATE FACTIO C N SHED PLAN€¦ · walls should be 11 feet and 5 1/2...

Page 1: 12X18 U S T O M E R S ATIS RATE FACTIO C N SHED PLAN€¦ · walls should be 11 feet and 5 1/2 inches while the height should be 6 feet and 7 1/2 inches. Use pressure treated timber

12X18LEAN TO SHED PLANFREE STREAMLINED VERSION

Supported & Recommended by our Friends & Partners:

2018

RATE

CU

STOMER SATISFACTION

CU

STOMER SATISFACTION

98,6%

Copyright © 2018 All Rights Reserved. Use of this PDF file constitutes acceptance of the 3DSHEDPLANS.COM User Terms and Privacy Policy. Page 1

Page 2: 12X18 U S T O M E R S ATIS RATE FACTIO C N SHED PLAN€¦ · walls should be 11 feet and 5 1/2 inches while the height should be 6 feet and 7 1/2 inches. Use pressure treated timber

COMPARISON BETWEEN OUR FREE & PREMIUM PLANS

FREE 12X18 SHED PLAN:

• Basic schematics

• Basic angles

• Basic measurements

• Simplified instructions

• No material list

PREMIUM 12X18 SHED PLAN:

• Instant email delivery (PDF) download

• Views from all angles

• Measurements for every part

• Full layouts for every step

• Step-by-step assembly instructions

• Full material / shopping list

• Full cutting list

• PRO-TIPS for every section

• Mobile / Tablet / PC / MAC ready

• Beginner friendly

VS.

NEED MORE INFORMATION ON THIS PREMIUM 12X18 SHED PLAN?

AVAILABLE ONLY AT THE OFFICIAL 3DSHEDPLANS™ WEBSITE

Copyright © 2018 All Rights Reserved. Use of this PDF file constitutes acceptance of the 3DSHEDPLANS.COM User Terms and Privacy Policy. Page 2

Page 3: 12X18 U S T O M E R S ATIS RATE FACTIO C N SHED PLAN€¦ · walls should be 11 feet and 5 1/2 inches while the height should be 6 feet and 7 1/2 inches. Use pressure treated timber

DISCLAIMER

3DSHEDPLANS™ is here to help and assist the DIYer. All information / advice is for general guidance only and whilst every effort is made to ensure that it is correct, it should not be relied upon as accurate. The information / advice contained within this document is intended for persons of no less than 18 years of age. Use of the information / advice contained within this document is at your own risk. It is the sole responsibility of any person(s) using the information / advice contained within this document that their level of competence is appropriate for the task they want to complete. All users of information / advice contained within this document should have all work checked / tested by a professional qualified trades person where applicable. You should be aware of current regulations on buildings, gas, water and electrical works (i.e. Part P) if you have any doubts we would advise you to research further information or contact the appropriate professional body.

LIABILITY3DSHEDPLANS™ and Netholics Media, LLC with the document through ownership and contribution will not accept any liability for any loss, damage, injury or negligence direct or indirect from use of the information / advice contained within this document. Any dispute arising from use of this document or disclaimer will be decided by the US courts under the relevant US law.

COPYRIGHT3DSHEDPLANS™ is official & registered trademark in the US. All of the contents (text/slogan) and artwork (graphics/logo) within this document are the copyrighted and trademarked property of 3DSHEDPLANS™ & Netholics Media, LLC. No part of the text or artwork may be reproduced by any means or in any form whatsoever without written permission, except for brief quotations embodied in literary articles or reviews. And no part of this document may be reproduced without written permission of the owners.This Information may be stored on computer for personal use only by the client (who purchased the plans from our official store), not for presentation or publication.

Copyright © 2018 All Rights Reserved. Use of this PDF file constitutes acceptance of the 3DSHEDPLANS.COM User Terms and Privacy Policy. Page 3

Page 4: 12X18 U S T O M E R S ATIS RATE FACTIO C N SHED PLAN€¦ · walls should be 11 feet and 5 1/2 inches while the height should be 6 feet and 7 1/2 inches. Use pressure treated timber

BASIC OVERVIEW AND DIMENSIONS

This 12x18 lean-to shed is extremely spacious yet attractive enough to add the much needed glamor to your

garden. You can store your gardening supplies as well spend your leisure hours performing your hobbies. The

shed has a width of 12 feet from the bottom and 12 feet and 7 inches from the top plate from the front. From the

sides, the shed has a width of 18 feet from the bottom and 18 feet and 1 inch from the top. The shed has two

windows on the side and one huge garage door on the front.

1

5' 7"

6' 2 1/4"

DOOR

12' 7"

Copyr

12'

FRONT VIEW

18' 1"

NOTE

Professional tip section is only available in PREMIUM (full) version of the plan.

18'

SIDE VIEW

9' 4"

ight © 2018 All Rights Reserved. Use of this PDF file constitutes acceptance of the 3DSHEDPLANS.COM User Terms and Privacy Policy. Page 4

Page 5: 12X18 U S T O M E R S ATIS RATE FACTIO C N SHED PLAN€¦ · walls should be 11 feet and 5 1/2 inches while the height should be 6 feet and 7 1/2 inches. Use pressure treated timber

FOUNDATION AND FLOOR

Building a solid foundation is crucial to the health of the entire shed since it will be holding up all the walls and

the roof. Use pressure treated timber to create joists and skids for creating an 18 feet wide and 12 feet deep

foundation. Use 3.5 inches galvanized nails to attach the parts together. Once you have built the foundation,

you need to use ¾ inches tongue and groove plywood to build the flooring.

2

NOTE

Professional tip section is only available in PREMIUM (full) version of the plan.

3/4" Tongue and Groove Plywood

FLOOR

FOUNDATION BASE

18'

12'

Copyright © 2018 All Rights Reserved. Use of this PDF file constitutes acceptance of the 3DSHEDPLANS.COM User Terms and Privacy Policy. Page 5

Page 6: 12X18 U S T O M E R S ATIS RATE FACTIO C N SHED PLAN€¦ · walls should be 11 feet and 5 1/2 inches while the height should be 6 feet and 7 1/2 inches. Use pressure treated timber

WALL STRUCTURES

Once the foundation and the floor is built, you will start working on the right and left walls. Both the walls will have a

width of 18 feet from the bottom plates. The right wall will have a height of 7 feet and 7 1/2 inches while the left wall

will have a height of 6 feet and 7 1/2 inches. Use pressure treated timber to build the joists and skids for the walls.

3

NOTE

Professional tip section is only available in PREMIUM (full) version of the plan.

7' 7 1/2"

18'

18'

RIGHT WALL

6' 7 1/2"

18'

18'

LEFT WALL

Copyright © 2018 All Rights Reserved. Use of this PDF file constitutes acceptance of the 3DSHEDPLANS.COM User Terms and Privacy Policy. Page 6

Page 7: 12X18 U S T O M E R S ATIS RATE FACTIO C N SHED PLAN€¦ · walls should be 11 feet and 5 1/2 inches while the height should be 6 feet and 7 1/2 inches. Use pressure treated timber

WALL STRUCTURES

After building the right and left walls, you will start working on the front and back walls. The width of both the

walls should be 11 feet and 5 1/2 inches while the height should be 6 feet and 7 1/2 inches. Use pressure

treated timber to build the skids and joists for the walls and nail them together using 3.5 inches galvanized nails.

4

NOTE

Professional tip section is only available in PREMIUM (full) version of the plan.

11' 8 1/2"

11' 5 1/2"

FRONT WALL

6' 7 1/2"

11' 8 1/2"

11' 5 1/2"

BACK WALL

6' 7 1/2"

Copyright © 2018 All Rights Reserved. Use of this PDF file constitutes acceptance of the 3DSHEDPLANS.COM User Terms and Privacy Policy. Page 7

Page 8: 12X18 U S T O M E R S ATIS RATE FACTIO C N SHED PLAN€¦ · walls should be 11 feet and 5 1/2 inches while the height should be 6 feet and 7 1/2 inches. Use pressure treated timber

ROOF SECTION

Finally, you will start working on the roofing of the shed. You will build a base with rafters of 18 feet width

and 12 feet and 7 inch depth. Start installing asphalt shingles once you are done building and installing

the base.

5

NOTE

Professional tip section is only available in PREMIUM (full) version of the plan.

Asphalt Shingles

18'

12' 7"

Copyright © 2018 All Rights Reserved. Use of this PDF file constitutes acceptance of the 3DSHEDPLANS.COM User Terms and Privacy Policy. Page 8

Page 9: 12X18 U S T O M E R S ATIS RATE FACTIO C N SHED PLAN€¦ · walls should be 11 feet and 5 1/2 inches while the height should be 6 feet and 7 1/2 inches. Use pressure treated timber

PREMIUM PLAN INCLUDES:

• Instant email delivery (PDF) download

• 30+ detailed 3D schematics

• Views from all angles

• Measurements for every part

• Full layouts for every step

• Step-by-step assembly instructions

• Full material / shopping list

• Full cutting list

• PRO-TIPS for every section

• Mobile / Tablet / PC / MAC friendly

• Beginner friendly

Supported & Recommended by our Friends & Partners:

2018

Wait no more! Save time & money now...Get your own professional 12X18 lean-to shed plan and start building your dream shed today!

Click here and go PREMIUM!

RATE

CU

STOMER SATISFACTION

CU

STOMER SATISFACTION

98,6%

AVAILABLE ONLY AT THE OFFICIAL 3DSHEDPLANS™ WEBSITECopyright © 2018 All Rights Reserved. Use of this PDF file constitutes acceptance of the 3DSHEDPLANS.COM User Terms and Privacy Policy. Page 9