12X10 PERGOLA - Backyard Discovery · • Owner's Manual • Frequently Asked Questions •...

• Owner's Manual• Frequently Asked Questions• Assembly Instructions• Warranty Information

12X10 PERGOLAModel: # 6214

Manufacturer: Backyard Discovery 3001 North Rouse Pittsburg, KS 66762 1-800-856-4445

Made in ChinaINS-6214-A-PERGOLA-ENG 04/25/14

Features the fastening system.

Register your new (Outdoor Product) on-line @www.swingsetsonline.com (you will also find any updates on

assembly instructions and information to order replacement parts)

Save this assembly manual for future reference in the event thatyou need to order replacement parts.

PLEASE HAVE THE FOLLOWING INFORMATION WHEN YOU MAKE YOUR CALL:

1 – MODEL NUMBER OF THE PRODUCT LOCATED ON THE FRONT OF THE ASSEMBLY MANUAL

2 – DESRIPTION OF THE PART FROM THE PARTS LIST

PLEASE READ THIS BEFORE STARTING ASSEMBLY

STOP Missing A Part?

CALL US BEFORE GOING

BACK TO THE STORE!

The store where you made your purchase

does not stock parts for this item.

If you have assembly questions or if you need parts,

whether they are missing or damaged

Call Toll-Free Help Line or visit www.swingsetsonline.com

1-800-765-4138

• READ THE ASSEMBLY MANUAL COMPLETELY, PAYING SPECIAL ATTENTION TO THE IMPORTANT TIPS AND

SAFETY INFORMATION.

• AFTER YOU HAVE READ THE ASSEMBLY MANUAL, YOU WILL BE ABLE TO DECIDE IF YOU NEED PROFESSIONAL

HELP TO COMPLETE THE ASSEMBLY OF THE PLAYSET.

• SEPARATE AND IDENTIFY ALL PARTS TO MAKE SURE THAT YOU HAVE ALL OF THE PARTS LISTED.

• IF YOU CAN’T FIND ALL OF THE PARTS, CHECK THE PACKING MATERIAL. SMALL PARTS MAY HAVE FALLEN INTO IT

DURING SHIPMENT.

• IF YOU HAVE PROBLEMS WITH THE ASSEMBLY OR IF ANY PART IS MISSING OR DAMAGED, PLEASE CALL THE

HELP LINE 1-800-765-4138 OR VISIT www.swingsetsonline.com.

Owner’s Manual Outdoor Product

ENG OWNER OP-2012

Dear Customer:

Please read entire booklet completely before beginning the assembly process.

Structures are not intended for public use. The Company does not warranty any of its

residential structures subjected to commercial use such as: Recreational Park, or any

similar Commercial Application.

Please follow all recommendations below. Failure to do so may result in the warranty

being void and/or safety violations that could result in serious injury. This manual

contains helpful information concerning Assembly Preparation, Installation Procedure,

and Required Maintenance. Always keep safety in mind as your structure is being built.

PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. KEEP THEM IN A SAFE

PLACE WHERE YOU CAN REFER TO THEM AS NEEDED. IN ORDER TO PROVIDE YOU

WITH THE MOST EFFICIENT SERVICE, IT IS REQUIRED THAT YOU PROVIDE US WITH THE

PART NUMBERS WHEN ORDERING PARTS.

For Your Records:

Please take time and fill out the information below. This information will be needed for

warranty issues.

Where Purchased: ______________

Date of Purchase: ________________

Installation Date: _______________

Installed by: ______________________

Tracking Number Reference Label Tracking ID number on the carton and back of the ID plate are included for tracking purposes associated with warranty claims.

Staple Receipt Here

Owner’s Manual Outdoor Product

ENG OWNER OP-2012

Maintenance Instructions:

1. Check all nuts and bolts twice monthly during the usage season and tighten as required.

(But not so tight that you crack the wood) It is particularly important that this

procedure be followed at the beginning of each season.

2. Oil all metallic moving parts monthly during the usage period.

3. Check all coverings for bolts and sharp edges twice monthly during usage season to be

certain they are in place. Replace when necessary. It is especially important to do this

at the beginning of each new season.

4. For rusted areas on metallic members such as hinges, brackets, etc. sand and repaint,

using a non lead-based paint meeting the requirements of Title 16 CRF Part 1303.

5. Inspect wood parts monthly. The grain of the wood sometimes will lift in the dry season

causing splinters to appear. Light sanding may be necessary to maintain a safe

environment. Treating your Product with protection (sealant) after sanding will help

prevent severe checking/splitting and other weather damage.

6. We have applied a waterborne translucent stain to your unit. This is done for color only.

Once or twice a year, depending on your climate conditions, you must apply some type

of protection (sealant) to the wood of your unit. Prior to the application of sealant,

lightly sand any “rough” spots on your set. Please note this is a requirement of your

warranty.

Outdoor Product Assembly Manual FAQs:

1. Is the wood treated with chemicals? Backyard Discovery uses 100% Chinese Cedar wood

which is naturally bug resistant, decay and rot resistant. To help ensure your families

safety, our wood is completely chemical free and we do not use pressure-treated wood.

The stain we use is a top coat using a water-based product that is for appearance only.

2. How often should the product be stained? Backyard Discovery recommends the product be

stained once each year. A water or oil based stain can be used at the customer’s discretion.

3. Why does it seem that my product is developing cracks? Wood is a natural material; no two

pieces are exactly alike. Each piece has its own characteristics and personality and reacts

differently to climate changes. When any wood product is exposed to the elements, it

develops “wood checks”. A check is the radial separation of the wood fibers running with

the grain of the wood. These are caused by the varying temperature and moisture

conditions. A check is not a crack – it does not affect the strength or durability of the wood

or structural integrity of the product.

4. Do Backyard Discovery products come with a warranty? Yes. All Backyard Discovery

products carry a 1-year replacement warranty on all parts for manufacturer’s defect. Our

wood carries a 5 year warranty on rot and decay as well. Please see warranty details for

more information.

5. What is the best way to get started assembling the product? Backyard Discovery

recommends taking all the parts out of the boxes and arranging them by part number

before you begin any assembly. This will not only allow faster assembly, but will also

identify any parts that may be missing or damaged so they can be replaced before

assembly. If parts are missing or need replacement, go to

www.swingsetsonline.com/support.aspx and follow the prompts to order them. Next, read

the assembly manual and get the tools ready for the job as recommended in the manual. If

the assembly manual is lost or misplaced a new one can be printed from Backyard

Discovery’s website: www.swingsetsonline.com .

6. The 2”x4” boards do not measure 2”x 4”. Why not? In the U.S. it’s common practice to

describe lumber dimensions using the rough cut sizes from the sawmill and not the finished

dimensions. Retailers, home stores, etc. all use this accepted practice for describing lumber

dimensions. However, Backyard Discovery products are designed and constructed using the

actual dimensions so everything fits properly and remains so during the life of the product.

For more information and frequently asked questions, please refer to our website at

www.swingsetsonline.com .

(Level 24")

(Square)

(Tape Measure)

(Cordless Drill or Electric Drill)

(Drill Attachments: Phillips

Head & Socket Driver) (An Adult w/ an Adult Helper)

(Rubber Mallet - Optional)

(Ladder)

(Phillips Screw Driver)

Tools Required for Installation:(These are the tools that are generally required for assembly of our outdoor products. These tools

are not included with the outdoor product purchase.)

(Concrete Drill Bit)

Basic Setup DimensionsPlace the set on level ground, concrete or grass. Backyard Discovery recommends at least

6 ft [2 m] from any structure or obstruction such as a fence, garage, house, overhanging

branches, laundry lines, or electrical wires.

Important Assembly Notes 1) While assembling unit, take time before and after each phase to make sure pergola is square and level. If pergola is not square and level, assembly will be difficult and improper assembly may result. Extra care must be taken to insure the pergola is square and level.2) Tighten bolts securely.3) Pay close attention to the ITEMS NEEDED FOR EACH PHASE. They can be a valuable aid when sorting your wood and hardware. Assembly will be made easier if items are sorted by step.4) Pay close attention to make sure you are using the correct hardware in the correct steps. Using incorrect hardware may result in improper assembly.5) Read each step thoroughly. The written steps may include important information not shown in the illustrations.

6'-7 1/2"7'-10 15/16"

6'-0"

6'-0"

12'-0"

10'-0"

Parts IdentificationWood Components

(NOT TO SCALE)

D1 - JOIST - W4L045851 3/8"x5 1/4"x114" (36x134x2896)(2)

D2 - JOIST - W4L045901 3/8"x5 1/4"x114" (36x134x2896)(2)

D3 - SLOTTED JOIST - W4L045861 3/8"x5 1/4"x114" (36x134x2896)(8)

D4 - JOIST - W4L045871 3/8"x5 1/4"x90" (36x134x2286)(2)

D5 - JOIST - W4L045911 3/8"x5 1/4"x90" (36x134x2286)(2)

D6 - JOIST END - W4L045881 3/8"x5 1/4"x15" (36x134x381)(12)


D8 - LONG ANGLE BRACE - W4L045931 3/8"x5 1/4"x37 1/8" (36x134x942)(4)

D9 - SHORT ANGLE BRACE - W4L045941 3/8"x5 1/4"x29 3/4" (36x134x755)(4)

P1 - LONG PURLIN - W4L045891 3/8"x1 3/8"x76 5/8" (36x36x1945)(12)

P2 - SHORT PURLIN - W4L045951 3/8"x1 3/8"x59 1/4" (36x36x1504)(12)

WP1 - PERGOLA POST - W4L045845 1/2"x5 1/2"x89 1/2" (140x140x2273)

(4)

Parts IdentificationHardware

VP - BOLT WH 5/16x7-1/4 BLK - H100196(34)

VM - BOLT WH 5/16x2-1/2 BLK - H100194(18) CQ - CONCRETE ANCHOR 3/16x2" - H100120(17)

- T

-40

To

rx W

ren

ch

- A

100

04

1(2

)VX - LAG SCREW WH 5/16x5-1/2 BLK - H100204(18)

VW - SCREW PFH 8x1/2 BLK - H100203(2)

VZ - LAG SCREW WH 5/16x3 BLK - H100206(9)

VU - SCREW PFH 8x2-1/2 BLK - H100201(100)

VT - SCREW PFH 8x1-1/2 BLK - H100200(17)

VS - WASHER LOCK EXT 12x19 BLK - H100199(52)

VR - WASHER LOCK EXT 8x19 BLK - H100198(76)

VL - NUT BARREL WH 5/16x1-1/2 BLK - H100193(34)

VK - NUT BARREL WH 5/16x7/8 BLK - H100192(18)

- T-40 Torx Bit - A100042(2)

VV - SCREW PWH 8x5/8 BLK - H100202(2)

Parts IdentificationAccessories

(NOT TO SCALE)

HT - FOOT 142 SQUARE POST - A100029(4)

VJ - LTP ID TAG (SMALL) WITHOUT AGES - A100387(1)

SQ - "A" REVISION TAG - A100314(1)

STEP 1

REPEAT PROCESS FOR OPPOSITE SIDE.

***HAND TIGHTEN ONLY AT THIS TIME.***

D4

D9

D9

NUT BARREL WH 5/16x7/8 BLK(4 PLCS)

WASHER LOCK EXT 12x19 BLK(4 PLCS)


BOLT WH 5/16x2-1/2 BLK(4 PLCS)

D4 - JOIST - W4L045871 3/8"x5 1/4"x90" (36x134x2286)(2)

D9 - SHORT ANGLE BRACE - W4L045941 3/8"x5 1/4"x29 3/4" (36x134x755)(4)

BOLT WH5/16x2-1/2

BLK (4)

WASHERLOCK EXT8x19 BLK

(4)


(4)

NUT BARRELWH 5/16x7/8

BLK (4)

D8 - LONG ANGLE BRACE - W4L045931 3/8"x5 1/4"x37 1/8" (36x134x942)(4)

STEP 2 REPEAT PROCESS FOR OPPOSITE SIDE.


(8)

BOLT WH5/16x2-1/2

BLK (8)


(8)

NUT BARRELWH 5/16x7/8

BLK (8)

D1

D8

D8

D1 - JOIST - W4L045851 3/8"x5 1/4"x114" (36x134x2896)(2)



NUT BARREL WH 5/16x7/8 BLK(4 PLCS)

WASHER LOCK EXT 12x19 BLK

(4 PLCS)

NOTE:ORIENT THE (6) HOLES TOWARDS THE TOP.

STEP 3

REPEAT PROCESS FOR OPPOSITE SIDE.




NUT BARREL WH 5/16x1-1/2 BLK(4 PLCS)

LAG SCREW WH 5/16x3 BLK(2 PLCS)


WP1

D5

90" JOIST - SUPPORTASSEMBLY


(12)

BOLT WH5/16x7-1/4

BLK (8)


(8)

NUT BARRELWH 5/16x1-1/2

BLK (8)

LAG SCREWWH 5/16x3

BLK (4)

D5 - JOIST - W4L045911 3/8"x5 1/4"x90" (36x134x2286)(2)

(4) WP1 - PERGOLA POST - W4L045845 1/2"x5 1/2"x89 1/2" (140x140x2273)

90" JOIST - SUPPORT ASSEMBLY(2)

ATTACH 'D5' TOINSIDE HOLELOCATIONS.

12

34

56

78

910

11

12

13

14

15

13

12

11

10

98

76

54

32

1

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

22212019181716151413121110987654321

!


BLK (8)


(12)

BOLT WH5/16x7-1/4

BLK (8)


(8)

LAG SCREWWH 5/16x3

BLK (4)

114" JOIST - SUPPORT ASSEMBLY(2)

D2 - JOIST - W4L045901 3/8"x5 1/4"x114" (36x134x2896)(2)

STEP 4 REPEAT PROCESS FOR OPPOSITE SIDE.


LAG SCREW WH 5/16x3 BLK(2 PLCS)





12

34

56

78

910

11

12

13

14

15

13

12

11

10

98

76

54

32

1

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

22212019181716151413121110987654321

!



BLK (4)


(4)


(4)

BOLT WH5/16x7-1/4

BLK (4)





STEP 5

D6


BLK (4)


(4)


(4)

BOLT WH5/16x7-1/4

BLK (4)



STEP 6





D7D6OUTSIDELOCATION

D7D6

D7 D6


BOLT WH 5/16x7-1/4 BLK

(4 PLCS)




(4)


BLK (4)


(4)

BOLT WH5/16x7-1/4

BLK (4)

STEP 7

D6



BOLT WH 5/16x7-1/4 BLK

(4 PLCS)






(4)


BLK (4)


(4)

BOLT WH5/16x7-1/4

BLK (4)

STEP 8

D7

D6

15 7/8"

(7 SPCS)

LAG SCREW WH 5/16x5-1/2 BLK(16 PLCS)


D3

D3 - SLOTTED JOIST - W4L045861 3/8"x5 1/4"x114" (36x134x2896)(8)


(16)

LAG SCREWWH 5/16x5-1/2

BLK (16)

STEP 9

JOIST SPACING

FLUSH



SCREW PFH 8x2-1/2 BLK(8 PLCS)

P1P2

SCREW PFH8x2-1/2 BLK

(8)

RIGHT

LEFT

STEP 10

6 1/8"

RIGHT SIDE VIEW

H


7 11/16"

LEFT

RIGHT

LEFT SIDE VIEW


(8)



STEP 11

P2P1

J

LEFT

RIGHT

P2

P1

7 11/16"

(10 SPCS)

RIGHT SIDE VIEW




(80)

STEP 12 ASSEMBLE REMAINING P1 AND P2 PURLINS ALTERNATING LOCATIONS AS SHOWN IN STEPS 10 AND 11.


STEP 13 DECIDE WHERE TO PLACE THE PERGOLA; GRASS, CONCRETE OR OTHER MATERIAL. PLACE THE PERGOLA EXACTLY WHERE IT WILL BE ANCHORED WHEN COMPLETED AND SLIDE A FOOT 'HT' UNDER EACH POST 'WP1'.

NOTE:IF NOT PLACING ON CONCRETE, PROCEED TO STEP 17.

HT

WP1

HT

WP1

HT

HT

WP1

WP1

HT - FOOT 142 SQUARE POST - A100029(4)

STEP 14

USE CHALK TO TRACE AROUND THE EDGES OF EACH FOOT 'HT'.

HT

CONCRETE ANCHOR 3/16x2"(16 PLCS)

CONCRETEANCHOR3/16x2"

(16)

STEP 15 MOVE THE PERGOLA ASIDE. PLACE EACH FOOT 'HT' INSIDE OF THE LINES DRAWN IN STEP 14. USING A CONCRETE DRILL BIT, PILOT DRILL ATTACHMENT HOLES INTO THE CONCRETE PAD. NEXT, USE THE 3/16"x2" CONCRETE ANCHORS TO ATTACH EACH FOOT TO THE CONCRETE SURFACE.

WP1

WP1

HT

HT

WP1 WP1

HT

HT

STEP 16 SET THE PERGOLA BACK IN PLACE, SETTING EACH POST 'WP1' INSIDE AN 'HT' FOOT..



(16)

STEP 17 ATTACH 'HT' FEET TO EACH 'WP1' POST USING 1-1/2" DECK SCREWS INTO EACH SIDE OF FOOT, AS SHOWN.

WP1

HT

SCREW PFH 8x1/2 BLK(2 PLCS)

SCREW PWH 8x5/8 BLK(2 PLCS)

SQ - "A" REVISION TAG - A100314(1)

VJ - LTP ID TAG (SMALL) WITHOUT AGES - A100387(1)

SCREW PWH8x5/8 BLK

(2)

SCREW PFH8x1/2 BLK

(2)

5 3/4"

9 1/2"

STEP 18 PLACE I.D. PLACARD ON FRONT OF POST APPROXIMATELY AS SHOWN.PLACE REVISION TAG ON REAR OF POST APPROXIMATELY AS SHOWN.

LEFT

RIGHT

FRONT

BACK

136"

136"

12

34

56

78

910

11

12

13

14

15

13

12

11

10

98

76

54

32

1

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

22212019181716151413121110987654321

!

SQUARE POSTS AND TIGHTENALL BOLTS AND SCREWS ATTHIS TIME.

Limited Warranty

This Limited Warranty by Backyard Discovery applies to products manufactured under the Backyard Discovery brand or its other brands including but not limited to Backyard Botanical, Adventure Playsets, and Leisure Time Products.

Backyard Discovery warrants that this product is free from defect in materials and workmanship for a period of one (1) year from the original date of purchase. This one (1) year warranty covers all parts including wood, hardware, and accessories. All wood carries a five (5) year pro-rated warranty against rot and decay. Refer to the schedule below for charges associated with replacement of parts under this Limited Warranty. In addition, Backyard Discovery will replace any parts within the first 30 days from date of purchase found to be missing from or damaged in the original packaging.

This warranty applies to the original owner and registrant and is non-transferable. Regular maintenance is required to assure maximum life and performance of this product and failure by the owner to maintain the product according to the maintenance requirements may void this warranty. Maintenance guidelines are provided in the Owner’s Manual.

This Limited Warranty does not cover:

Labor for any inspection Labor for replacement of any defective item(s) Incidental or consequential damages Cosmetic defects which do not affect performance or integrity of a part or the entire product Vandalism, improper use, failure due to loading or use beyond the capacities stated in the applicable

Assembly Manual. Acts of nature including but not limited to wind, storms, hail, floods, excessive water exposure Improper installation including but not limited to installation on uneven, unlevel, or soft ground Minor twisting, warping, checking, or any other natural occurring properties of wood that do not affect

performance or integrity

Backyard Discovery products have been designed for safety and quality. Any modifications made to the original product could damage the structural integrity of the unit leading to failure and possible injury. Modification voids any and all warranties and Backyard Discovery assumes no liability for any modified products or consequences resulting from failure of a modified product.

This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a Backyard Discovery product be used in public settings. Such use may lead to product failure and potential injury. Any and all public use will void this warranty. Backyard Discovery disclaims all other representations and warranties of any kind, express or implied.

This Warranty gives you specific legal rights. You may have other rights as well which vary from state to state or province to province. This warranty excludes all consequential damages, however, some states do not allow the limitation or exclusion of consequential damages and therefore this limitation may not apply to you.

Pro Rated Part Replacement Schedule

Product Age Customer Pays All Parts 0-30 days from date of purchase $0 and free shipping 31 days to 1 year $0 + S&H

Wood Rot and Decay Only 1 year $0 and free shipping 2 years 20% + S&H 3 years 40% + S&H 4 years 60% + S&H 5 years 80% + S&H Over 5 years 100% + S&H

12X10 PERGOLA - Backyard Discovery · • Owner's Manual • Frequently Asked Questions •...

Documents

Transcript of 12X10 PERGOLA - Backyard Discovery · • Owner's Manual • Frequently Asked Questions •...