12ed11 – Advanced Machine Tool Design Ppt
-
Upload
bradeesh-moorthy -
Category
Documents
-
view
236 -
download
7
description
Transcript of 12ed11 – Advanced Machine Tool Design Ppt
![Page 1: 12ed11 – Advanced Machine Tool Design Ppt](https://reader035.fdocuments.us/reader035/viewer/2022062300/563dba59550346aa9aa4d8be/html5/thumbnails/1.jpg)
12ED11 – ADVANCED MACHINE TOOL DESIGN
TOPICS: STATIC AND DYNAMIC STIFFNESS
S.BRADEESH MOORTHY, APME
![Page 2: 12ed11 – Advanced Machine Tool Design Ppt](https://reader035.fdocuments.us/reader035/viewer/2022062300/563dba59550346aa9aa4d8be/html5/thumbnails/2.jpg)
INTRODUCTIONMachine tool design
It deals with the design considerations of the machine components and the machine as a whole.
Machine tool structures Components of machine tools such as beds, bases, columns, box type housings, overarm, carriages, tables etc .
Types of machine tool structures:i. Beds and bases – sub assemblies are mountedii. Housings – individual units are assembled eg speed box,
spindle head iii. Supporting and moving work piece / cutter – table,
carriage, tailstock etc
![Page 3: 12ed11 – Advanced Machine Tool Design Ppt](https://reader035.fdocuments.us/reader035/viewer/2022062300/563dba59550346aa9aa4d8be/html5/thumbnails/3.jpg)
Requirements & necessary conditions for structures
Requirements• Mating surfaces to be machined with high degree of
accuracy for desired geometrical accuracy.• Geometrical accuracy to be maintained through out the
life of machine.• Provide safe operations and maintenance• Ensure stresses does not exceed safe limit.Conditionsi. Proper material selectionii. High static and dynamic stiffness
![Page 4: 12ed11 – Advanced Machine Tool Design Ppt](https://reader035.fdocuments.us/reader035/viewer/2022062300/563dba59550346aa9aa4d8be/html5/thumbnails/4.jpg)
STATIC & DYNAMIC STIFFNESS
• Machine tool and its cutting process can be expressed by a closed loop.
• Machine tool interacts with the cutting process.• Both machine tool and cutting process are represented by
their transfer functions.• If input to the machine (dP) is static then the output (dY) is
static in nature.• If the input to the machine (dP) is dynamic in nature then
the output (dY) is also dynamic in nature.• Designer should have good knowledge on the cumulative
static and dynamic characteristics of machine tool as well as elements with which the machine tool is made.
![Page 5: 12ed11 – Advanced Machine Tool Design Ppt](https://reader035.fdocuments.us/reader035/viewer/2022062300/563dba59550346aa9aa4d8be/html5/thumbnails/5.jpg)
MACHINE TOOL CUTTING PROCESS – BLOCK DIAGRAM REPRESENTATION
Machine tool transfer function
Cutting process transfer function
y
Y(t)
p(t)
p
![Page 6: 12ed11 – Advanced Machine Tool Design Ppt](https://reader035.fdocuments.us/reader035/viewer/2022062300/563dba59550346aa9aa4d8be/html5/thumbnails/6.jpg)
STATIC STIFFNESS • Behavior of element (stiffness)under
static conditions is examined from its force- displacement diagram.
• Generally the relation is non-linear.• Generally the stiffness is measured along
the direction of the force.• If the stiffness is measured along some
other direction, it is called cross stiffness.• Inverse of stiffness is compliance which is
normally used for analyzing static behavior of machine elements.
• Stiffness behavior of elements affects parameters of machining and quality of machined surface.
![Page 7: 12ed11 – Advanced Machine Tool Design Ppt](https://reader035.fdocuments.us/reader035/viewer/2022062300/563dba59550346aa9aa4d8be/html5/thumbnails/7.jpg)
ASSESSMENT OF STATIC STIFFNESSi. Static stiffness with respect
to work piece accuracy• Cross stiffness represented by
K’ = P/Y’P – Resultant cutting force between cutting tool and work pieceY’ – relative displacement normal to machined surface
• Higher K’ represents lesser displacement perpendicular to machined surface which results in better accuracy.
![Page 8: 12ed11 – Advanced Machine Tool Design Ppt](https://reader035.fdocuments.us/reader035/viewer/2022062300/563dba59550346aa9aa4d8be/html5/thumbnails/8.jpg)
Cont….ii. Static stiffness with respect to
dynamic stablity• Cross stiffness represented by K = P/Y
P – Resultant cutting force between cutting tool and work pieceY – relative displacement normal to surface of cut
• Y – significant in chip thickness, major role in machine tool chatter.
![Page 9: 12ed11 – Advanced Machine Tool Design Ppt](https://reader035.fdocuments.us/reader035/viewer/2022062300/563dba59550346aa9aa4d8be/html5/thumbnails/9.jpg)
REPRESENTATION OF STATIC STIFFNESS
• Every member undergoes deformation under load so it can be considered as a spring.
• Machine tool can be reduced into a combination of springs in series or parallel.
Springs in series
Springs in parallel
321 YYYY
321
321
1111CCC
kkkk
321321 , yyyykkkk
![Page 10: 12ed11 – Advanced Machine Tool Design Ppt](https://reader035.fdocuments.us/reader035/viewer/2022062300/563dba59550346aa9aa4d8be/html5/thumbnails/10.jpg)
Example for series system• Gear transmission system with four shafts.• The total compliance for the machine tool is the summation of reduced
compliances• Compliance • Major contributor of C is C4, if all are speed reduction.• So compliance can be improved by improving the weak element shaft 4.
42433
243
2322
243
232
2211 ...... CiCiiCiiiCC
![Page 11: 12ed11 – Advanced Machine Tool Design Ppt](https://reader035.fdocuments.us/reader035/viewer/2022062300/563dba59550346aa9aa4d8be/html5/thumbnails/11.jpg)
Example for series system
• If one spring contributes to 80% of stiffness and other two remaining 20%.
• Increasing stiffness of stronger contributes to increase in stiffness rather than the other.
321321 , yyyykkkk
![Page 12: 12ed11 – Advanced Machine Tool Design Ppt](https://reader035.fdocuments.us/reader035/viewer/2022062300/563dba59550346aa9aa4d8be/html5/thumbnails/12.jpg)
DYNAMIC STIFFNESS• Dynamic loading causes dynamic displacement.• Sometimes for constant dynamic force response differs with frequency of
input.• The ratio Kdyn =Pdyn/ Ydyn is dynamic stiffness.• Dynamic and static stiffness related by
Where A- magnification factor.• ‘A’ depends on i) damping factor (ii) Frequency ratio• If load is independent of frequency then
• If load is due to unbalanced force then
AYY stdyn .
n
2221
21
1
A
222
2
2
21
A
![Page 13: 12ed11 – Advanced Machine Tool Design Ppt](https://reader035.fdocuments.us/reader035/viewer/2022062300/563dba59550346aa9aa4d8be/html5/thumbnails/13.jpg)
VARIATION OF ‘A’ WITH RESPECT TO
![Page 14: 12ed11 – Advanced Machine Tool Design Ppt](https://reader035.fdocuments.us/reader035/viewer/2022062300/563dba59550346aa9aa4d8be/html5/thumbnails/14.jpg)
Cont…..From the graphs• ‘A’ decreases if is increased• ‘A’ is small if exciting frequency is away from natural frequency• If is 0.25 - 2.5 then displacement under dynamic condition is nearly
equal to displacement in static condition.
![Page 15: 12ed11 – Advanced Machine Tool Design Ppt](https://reader035.fdocuments.us/reader035/viewer/2022062300/563dba59550346aa9aa4d8be/html5/thumbnails/15.jpg)
REPRESENTATION OF VIBRATION BEHAVIOUR AND CONTROL
pkykdt
dyp
dt
ydm iiii
2
2
• By solving n independent equations the displacements are found out.
•Resultant displacement y = y1 +y2+y3+ -----+yn
•Dynamic compliance found out by y/P•In simple modes of vibration contribution of stiffness of elements is same in overall stiffness of machine tool.•By increasing stiffness of elements overall stiffness can be increased.•Highest among the natural frequency should desirably be 2.5 times less than the highest excitation frequency. •Lowest among the natural frequency should desirably be 2.5 times greater than the lowest excitation frequency.