128858256 Nokia Flexi WBTS IP Commissioning Settings
-
Upload
ahmed-bouri -
Category
Documents
-
view
34 -
download
8
Transcript of 128858256 Nokia Flexi WBTS IP Commissioning Settings
-
Nokia Flexi WBTS IP commissioning settings
BTS ID 1 (FSME + FTLB + FXDA1 + FRGP2)
BTS name MGH4999
BTS location Mghira testbed
BTS description 2+2+2, 20W
BTS IP addresses:Subnet address 10.209.0.0
Subnet mask 255.255.255.248 / 29
TRS address 10.209.0.1
BTS address 10.209.0.2
DHCP client address range 10.209.0.3 10.209.0.6
RNC address 10.207.19.132
NTP address 10.207.19.135
LDAP server Not in use
Certificate management Not in use
-
TLS for OAM interface Probing
BTS firewall Ping and traceroute enabled
FTP server on FTM Enabled
TRS settings
Physical layer configuration:
FTM type FTLB
Transport mode Iub IP
Interface type E1
PDH interfaces Not in use
Ethernet interfaces EIF2 in use => Autodetect
Ethernet switching QoS aware Ethernet switching not in use
Queue weights Queue 2 = 8, Queue 3 = 4, Queues 4-6 = 1
QoS classification:
-
Mode DSCP
Priority queue for Non-IP frames 1
DSCP to priority queue mapping DSCP 46, 48 => Queue 1
DSCP 34, 36, 38 => Queue 2
DSCP 26, 28, 30 => Queue 3
DSCP 10, 12, 14, 18, 20, 22 => Queue 4
VLAN aware configuration VLAN aware switching not in use
Ethernet interfaces shaper Speed and duplex (Egress & Ingress)
Egress burst size = 0.0%
Ethernet link OAM Not in use
Ethernet service OAM Not in use
CIR = 1.0 Mbit/s
Quality of Service Defaults in use
IP interfaces:
Settings MTU = 1500 octets
OSPFv2 Not in use
-
Transport Ethernet interface:
Interface address None (VLANs in use)
Traffic shaping type WFQ
Shaper information rate 100.0 Mbit/sShaper burst size 1522 octets
Committed information rate 5.0 Mbit/s
Enable QoS Yes
Include Ethernet overhead No
Proxy ARP Not in use
OSPFv2 parameters OSPF disabled
VLAN 901:
VLAN ID 901
Address 10.117.250.2 / 29
CES over PSN VLAN No
Committed information rate 0.5 Mbit/s
Enable QoS No
Proxy ARP Not in use
OSPFv2 parameters OSPF disabled
VLAN 902:
VLAN ID 902
-
Address 10.167.250.2 / 29
CES over PSN VLAN No
Committed information rate 0.1 Mbit/s
Enable QoS Yes
Proxy ARP Not in use
OSPFv2 parameters OSPF disabled
VLAN 903:
VLAN ID 903
Address 10.127.250.2 / 29
CES over PSN VLAN No
Committed information rate 4.3 Mbit/s
Enable QoS Yes
Proxy ARP Not in use
OSPFv2 parameters OSPF disabled
VLAN 904:
VLAN ID 904
Address 10.177.250.2 / 29
CES over PSN VLAN No
Committed information rate 0.1 Mbit/s
Enable QoS No
-
Proxy ARP Not in use
OSPFv2 parameters OSPF disabled
CES over PSN settings Minimum UDP port = 53248
IUB IP settings:
Far-end SCTP subnet 10.207.18.0 / 26
Minimum SCTP port 49152
Minimum UDP port 49152
CAC Committed bit rate 5.0 Mbps
Signalling bit rate 500 Kbps
DCN bit rate 100 Kbps
Frame protocol multiplexing:
Local UDP port 65535
Remote UDP port 65535
Multiplexing delay 2 ms
Multiplexing amount 30 packets
Timing over Packet Not in use
Application addresses:
-
User plane 1 10.167.250.2
User plane 2 10.127.250.2
Control plane 10.117.250.2
Management plane 10.209.0.1
RTT measurement Reflector not in use
TWAMP sessions Not in use
Synchronization:
Timing sources None
Sync Ethernet regenerator Not in use
BTS routing:
Default gateway 10.177.250.1
BFD sessions None
Static routes:
Destination Netmask Gateway Preference
10.207.19.72 255.255.255.248 10.167.250.1 1
10.207.19.80 255.255.255.248 10.127.250.1 1
10.207.18.0 255.255.255.192 10.117.250.1 1
-
Route reinstallation delay 0s
IP filtering Restricted mode for LMP = On
BTS settings
Configuration name 2+2+2, 20W
External 2.048 MHz sync output Not in useForward sync in co-siting Not in use
Security for Ethernet ports Not in useEnter BTS to test state No
Sync sources for BTS FM External 2.048 MHz synchronization in use
IP Iub signaling settings Max assoc. retransmissions = 5
Max path retransmissions = 5
Automatic license distribution:
Enable SW monitoring No
Automatic licensing in use YesR99 channel elements None
-
Concurrent mode settings RF Sharing not enabled
Local Cell IDs Cell 1 FRGP2, Ant 1&2 @ 20W
(FRGP2 only) Cell 2 FRGP2, Ant 3&4 @ 20W
Cell 3 FRGP2, Ant 5&6 @ 20W
Intelligent shutdown Not in use
Carrier frequency Cell 1 = 10613
(UARFCN) Cell 2 = 10613
Cell 3 = 10613
Local cell groups in use No
BB and HSPA license allocations None
Mapping HSPA to BB HW No
HSDPA settings:
HSDPA 16 QAM support In use
HSDPA PFRP scheduler In use
HSDPA resource allocation None
HSDPA shared scheduler Not in use
-
HSDPA capacity sets:
BTS processing set 1 Not in use
BTS processing set 2 3 in use
BTS processing set 3 1 in use
HSDPA throughput:
Scheduler 1 18 steps
Scheduler 2 3 steps
HSDPA Iub delay thresholds Defaults in use
HSUPA settings:
HSUPA FDE in use No
HSUPA resource allocation Defaults in use
HS cell FACH state Not in use
Happy bit ratio filtering In use (both), UPH threshold = 10 dB
HSUPA capacity sets:
BTS processing set 1 3 in use
-
SPI Class settings Defaults in use
Resource reservation for non-NBR 10%
Antenna line management:
3GPP/AISG communication Not in use
DC voltage Not in use
Antenna line features:
SW update for antenna devices Not in use
Flexi WBTS 3GPP antenna tilt Not in use
Antenna line supervision Not in use
RX signal level monitoring Not in use
AISG MHA settings Not in use
Antenna line settings:
FR1.2.1-ANT1 & 3 & 5Antenna settings Feeder loss = -3.0 dB PHS filter not in use
Multiradio combiner not in use
Multiplexer not in use
VSWR minor fault = 1.5 VSWR major fault = 1.7
-
Additional RX gain = 0.0 dB
Uplink delay = 0 ns
Forced feeded voltage = Not set
RTT measurements User-defined RTT delay = 8.2 nsMHA settings MHA not in use
FR1.2.1-ANT2 & 4 & 6Antenna settings Feeder loss = -3.0 dB
PHS filter not in use
Multiplexer not in use
Additional RX gain = 0.0 dB
Uplink delay = 0 ns
RTT measurements User-defined RTT delay = 8.2 ns
MHA settings MHA not in use
Siemens AISG1.1 TMA/RET Not in use
RET settings Not in use
System module EAC settings None
Radio module EAC settings None
-
No related Telecom Tutorials found.