1260-35 MULTIPLEXER / SCANNERmanuals.repeater-builder.com/te-files/RACAL/RACAL 1260-35 INST.pdf ·...
Transcript of 1260-35 MULTIPLEXER / SCANNERmanuals.repeater-builder.com/te-files/RACAL/RACAL 1260-35 INST.pdf ·...
1260 VXISWITCHING CARD
1260-35MULTIPLEXER / SCANNER
PUBLICATION NO. 980673-006
RACAL INSTRUMENTS
Racal Instruments, Inc.4 Goodyear St., Irvine, CA 92618-2002
Tel: (800) 722-3262, FAX: (949) 859-7309
Racal Instruments, Ltd.480 Bath Road, Slough, Berkshire, SL1 6BE, United Kingdom
Tel: +44 (0) 8706 080134; FAX: +44 (0) 1753 791290
Racal Systems Electronique S.A.18 Avenue Dutartre, 78150 LeChesnay, FranceTel: +33 (1) 3923 2222; FAX: +33 (1) 3923 2225
Racal Systems Elettronica s.r.l.Strada 2-Palazzo C4, 20090 Milanofiori Assago, Milan, Italy
Tel: +39 (02) 5750 1796; FAX +39 (02) 5750 1828
Racal Elektronik System GmbH.Frankenforster Strasse 21, 51427 Bergisch Gladbach, Germany
Tel:+49 2204 92220; FAX: +49 2204 21491
Racal Australia Pty. Ltd.3 Powells Road, Brookvale, NSW 2100, AustraliaTel: +61 (2) 9936 7000, FAX: +61 (2) 9936 7036
Racal Electronics Pte. Ltd.26 Ayer Rajah Crescent, 04-06/07 Ayer Rajah Industrial Estate, Singapore 0513.
Tel: +65 7792200, FAX: +65 7785400
Racal Instruments, Ltd.Unit 5, 25F., Mega Trade Center, No 1, Mei Wan Road, Tsuen Wan, Hong Kong, PRC
Tel: +852 2405 5500, FAX: +852 2416 4335
http://www.racalinst.com
PUBLICATION DATE: April 10, 2000
Copyright 1997 by Racal Instruments, Inc. Printed in the United States of America. All rights reserved.This book or parts thereof may not be reproduced in any form without written permission of the publisher.
WARRANTY STATEMENT
All Racal Instruments, Inc. products are designed and manufactured to exacting standards and in fullconformance to Racal’s ISO 9001 procedures.
For the specific terms of your standard warranty, or optional extended warranty or service agreement, contactyour Racal customer service advisor. Please have the following information available to facilitate service.
1. Product serial number
2. Product model number
3. Your company and contact information
You may contact your customer service advisor by:
E-Mail: [email protected]
Telephone: +1 800 722 3262 (USA)+44(0) 8706 080134 (UK)+852 2405 5500 (Hong Kong)
Fax: +1 949 859 7309 (USA)+44(0) 1628 662017 (UK)+852 2416 4335 (Hong Kong)
RETURN of PRODUCT
Authorization is required from Racal Instruments before you send us your product for service or calibration. Callyour nearest Racal Instruments support facility. A list is located on the last page of this manual. If you areunsure where to call, contact Racal Instruments, Inc. Customer Support Department in Irvine, California, USA at1-800-722-3262 or 1-949-859-8999 or via fax at 1-949-859-7139. We can be reached at:[email protected].
PROPRIETARY NOTICE
This document and the technical data herein disclosed, are proprietary to Racal Instruments, and shall not,without express written permission of Racal Instruments, be used, in whole or in part to solicit quotations from acompetitive source or used for manufacture by anyone other than Racal Instruments. The information herein hasbeen developed at private expense, and may only be used for operation and maintenance reference purposes orfor purposes of engineering evaluation and incorporation into technical specifications and other documents whichspecify procurement of products from Racal Instruments.
FOR YOUR SAFETY
Before undertaking any troubleshooting, maintenance or exploratory procedure, read carefully theWARNINGS and CAUTION notices.
This equipment contains voltage hazardous to human life and safety, and is capable of inflictingpersonal injury.
If this instrument is to be powered from the AC line (mains) through an autotransformer, ensure thecommon connector is connected to the neutral (earth pole) of the power supply.
Before operating the unit, ensure the conductor (green wire) is connected to the ground (earth)conductor of the power outlet. Do not use a two-conductor extension cord or a three-prong/two-prong adapter. This will defeat the protective feature of the third conductor in the power cord.
Maintenance and calibration procedures sometimes call for operation of the unit with power appliedand protective covers removed. Read the procedures and heed warnings to avoid “live” circuitpoints.
Before operating this instrument:
1. Ensure the instrument is configured to operate on the voltage at the power source. SeeInstallation Section.
2. Ensure the proper fuse is in place for the power source to operate.
3. Ensure all other devices connected to or in proximity to this instrument are properly grounded orconnected to the protective third-wire earth ground.
If the instrument:
- fails to operate satisfactorily- shows visible damage- has been stored under unfavorable conditions- has sustained stress
Do not operate until performance is checked by qualified personnel.
This page was left intentionally blank.
Amendment Page 6/98 1
NOTE FOR SYSTEMS WITH 1260-OPT 01T
The “Module-Specific Syntax” section of this manual shows the command syntax for the1260-01S Smart Card. If you are using the newer 1260-01T Smart Card, the commandswill NOT work as shown.
Consult the 1260-01T Manual for a description of the commands that may be used with the1260-01T Smart Card.
The channel numbers described in this manual are valid for the 1260-01T. The channelnumbers continue to be used for the 1260-01T.
The syntax of the commands that use channel numbers has changed for those cardscontrolled by the 1260-01T.
The new syntax used to close a channel is:
CLOSE (@ <module address> ( <channel> ) )
For example, for a relay module whose <module address> is set to 7, closing <channel> 0is performed with the command:
CLOSE (@7 (0))
Using the older 1260-01S, the command would be (as shown in this manual):
CLOSE 7.0
Many other command syntax differences exist. Please consult chapter 2 of the 1260-01Tmanual for a description of the commands that are available for the 1260-01T.
Control Information for the 1260-35A
The 1260-35A operates as a 4-wire MUX. Thus, when a channel is operated, 2 relays must be operated inparallel. For each channel, when a bit of Control Register X is set (or cleared), the same bit of ControlRegister X+6 must also be set (or cleared).
Each channel on this module is therefore controlled by setting or clearing two bits, one each in two differentControl Registers. Control Registers on the module operate 8 channels simultaneously. There are eightcontrol bits per Control Register. Setting the bit to a 1 closes the relay; setting the bit to a 0 opens the relay.
The table below shows the mapping between logical channels used to operate the relay module in message-based mode and the bits within the Control Registers which may be used to operate the channel in register-based mode.
Each Control Register is located 2 addresses from the previous Control Register. That is, each ControlRegister is located at an odd address. This is shown in Table 2-2 of the 1260-01T manual. Control Register 0is located at the “Base A24 Address” for the module. Consult the “Register-Based Operation” Section ofChapter 2 of the 1260-01T manual for a description of calculating control register addresses
For example, when closing channel 13, both byte 1 and byte 7 must have bit 5 set.
Channel Control Register Control Bit0 0 and 6 01 0 and 6 12 0 and 6 23 0 and 6 34 0 and 6 45 0 and 6 56 0 and 6 67 0 and 6 78 1 and 7 09 1 and 7 110 1 and 7 211 1 and 7 312 1 and 7 413 1 and 7 514 1 and 7 615 1 and 7 716 2 and 8 017 2 and 8 118 2 and 8 219 2 and 8 320 2 and 8 421 2 and 8 522 2 and 8 623 2 and 8 724 3 and 9 025 3 and 9 126 3 and 9 227 3 and 9 328 3 and 9 429 3 and 9 530 3 and 9 631 3 and 9 732 4 and 10 033 4 and 10 134 4 and 10 235 4 and 10 336 4 and 10 437 4 and 10 538 4 and 10 639 4 and 10 7
Channel Control Register Control Bit40 5 and 11 041 5 and 11 142 5 and 11 243 5 and 11 344 5 and 11 445 5 and 11 546 5 and 11 647 5 and 11 7
Control Information for the 1260-35B
The following information describes the control-register-to-relay-channel mapping for a 1260-35B RelayModule. This information may be used to control a 1260-35B when using a 1260-01T in the register-basedmode of operation.
Each relay on this module is controlled by setting or clearing a single bit within a Control Register. ControlRegisters on the module operate 8 channels simultaneously. There are eight control bits per Control Register.Setting the bit to a 1 closes the relay; setting the bit to a 0 opens the relay.
The table below shows the mapping from logical channels to control bits. The logical channels are used whenoperating the relay module in message-based mode. The control bits within the Control Registers are used tooperate the module in register-based mode.
Each Control Register is located 2 addresses from the previous Control Register. That is, each ControlRegister is located at an odd address. This is shown in Table 2-2 of the 1260-01T manual. Control Register 0is located at the “Base A24 Address” for the module. Consult the “Register-Based Operation” Section ofChapter 2 of the 1260-01T manual for a description of calculating control register addresses.
Channel Control Register Control Bit0 0 01 0 12 0 23 0 34 0 45 0 56 0 67 0 78 1 09 1 110 1 211 1 312 1 413 1 514 1 615 1 716 2 017 2 118 2 219 2 320 2 421 2 522 2 623 2 724 3 025 3 126 3 227 3 328 3 429 3 530 3 631 3 732 4 033 4 134 4 235 4 336 4 437 4 538 4 639 4 740 5 041 5 142 5 243 5 3
Channel Control Register Control Bit44 5 445 5 546 5 647 5 748 6 049 6 150 6 251 6 352 6 453 6 554 6 655 6 756 7 057 7 158 7 259 7 360 7 461 7 562 7 663 7 764 8 065 8 166 8 267 8 368 8 469 8 570 8 671 8 772 9 073 9 174 9 275 9 376 9 477 9 578 9 679 9 780 10 081 10 182 10 283 10 384 10 485 10 586 10 687 10 788 11 089 11 190 11 291 11 392 11 493 11 594 11 695 11 796 12 0
User Manual 1260-35
i
Table of Contents
Chapter 1MODULE SPECIFICATION .......................................................................................................... 1-1
1260-35 Module Specification ................................................................................................... 1-1Specifications ........................................................................................................................ 1-2
Ordering Information ................................................................................................................. 1-3Safety........................................................................................................................................ 1-3Product Support ........................................................................................................................ 1-3
Chapter 2INSTALLATION INSTRUCTIONS ................................................................................................ 2-1
Unpacking and Inspection ......................................................................................................... 2-1Reshipment Instructions............................................................................................................ 2-1Option 01 Installation ................................................................................................................ 2-2Module Installation .................................................................................................................... 2-21260-35 ID Byte ........................................................................................................................ 2-2Configuration............................................................................................................................. 2-2Analog Bus................................................................................................................................ 2-4
Chapter 3MODULE SPECIFIC SYNTAX...................................................................................................... 3-1
1260-35 Module Specific Syntax ............................................................................................... 3-1Syntax ................................................................................................................................... 3-1CLOSE Command................................................................................................................. 3-2PSETUP Command............................................................................................................... 3-2PDATAOUT Command.......................................................................................................... 3-2Operation In Single-Wire Mode ............................................................................................. 3-3
Chapter 4DRAWINGS.................................................................................................................................. 4-1
Chapter 5PARTS LIST................................................................................................................................. 5-1
User Manual 1260-35
ii
Chapter 6OPTIONAL HARNESS ASSEMBLIES.......................................................................................... 6-1
Chapter 7PRODUCT SUPPORT ................................................................................................................. 7-1
Product Support ........................................................................................................................ 7-1Reshipment Instructions ........................................................................................................... 7-1Support Offices ......................................................................................................................... 7-2
User Manual 1260-35
iii
List of Figures
Figure 1-1, 1260-35 Signal Multiplexer/Scanner Module............................................................... 1-1
Figure 3-1, 1260-35 Block Diagram .............................................................................................. 3-7Figure 3-2, 1260-35 Pin Connections, Front View......................................................................... 3-8
List of Tables
Table 2-1, 1260-35 Jumper Installation......................................................................................... 2-3
Table 3-1, 1260-35 Channel Closure ............................................................................................ 3-3Table 3-1, 1260-35 Channel Closure (continued) ......................................................................... 3-5Table 3-1, 1260-35 Channel Closure (continued) ......................................................................... 3-6
User Manual 1260-35
iv
This page was left intentionally blank.
User Manual 1260-35
Module Specification 1-1
Chapter 1
MODULE SPECIFICATION
1260-35 ModuleSpecification
The 1260-35 Signal Multiplexer/Scanner Module is a 1 x 96multiplexer. It switches two lines per channel and has thecapability of being configured as two 1 x 48 multiplexers, four 1 x24 multiplexers, eight 1 x 12 multiplexers, or sixteen 1 x 6multiplexers. The configuration is user selectable, but is suppliedby the factory in one 1 x 96 two-wire mode. A block diagram of themodule is shown in Figure 3-1
Figure 1-1, 1260-35 Signal Multiplexer/Scanner Module
User Manual 1260-35
Module Specification 1-2
Specifications Switch Configurations Four-wire Mode Any configuration Two-wire Mode Any configuration
User Connector 64-Pin (2 Row) IDC Quick Disconnect
Maximum Switchable Voltage 220VDC, 250VAC RMS(Terminal-Terminal or Terminal-Chassis
Maximum Switchable Current 1A DC or 1A RMS
Maximum Switchable PowerPer Channel 30W DC, 62.5VA AC
Path Resistance <0.5Ω (1 X 6 configuration) <1.0Ω (1 X 96 configuration)
Isolation Hi-Lo >7.5 X 108Ω
CapacitanceOpen Channel <600pf (1 x 96 configuration)
Channel-Chassis <60pf (1 x 6 configuration) <200pf (1 x 96 configuration) Hi-Lo <50pf (1 x 6 configuration) <600pf (1 x 96 configuration)
Bandwidth (50Ω Termination) >50 MHz (1 x 6 configuration) >15 MHz (1 x 48 configuration)
* A crimp connector kit is also available for this module (PIN 404975-001). A strain relief option can be ordered separately for this crimp connector kit.
Insertion Loss (50Ω ) <.1 dB to 100kHz1 x 6 Configuration <.5 dB to 1MHz
<1 dB to 10MHz
Insertion Loss (50Ω ) <3 dB to 8MHz1 x 96 Configuration
Crosstalk (50Ω termination) <-90 dB to 100kHz <-70 dB to 1 MHz <-23 dB to 10MHz
Cooling Requirement
User Manual 1260-35
Module Specification 1-3
Airflow 4.0 liters/sec Backpressure 0.5mm H20
Power Requirements +5V, Ipm 0.4A (2.8A with Option 01 installed) +24V, Idm 10mA per energized relay
Weight 3.07lbs (1.33Kg) 3.35lbs (1.51Kg) with Option 01 installed
Minimum Option 01 Firmware Revision 17.1
OrderingInformation
Model Number
1260-35
1260-35A
Description
1 X 96 Signal Multiplexer/Scanner, User Conn: IDC1 X 96 Signal Multiplexer/
Scanner, User Conn: Crimp
Part Number
404944
404944-001
Safety Refer to the “FOR YOUR SAFETY” page preceding the Table ofContents. Following all NOTES, CAUTIONS, and WARNINGS toensure personal safety and prevent damage to the instrument.
Product Support Racal Instruments has a complete Service and Parts Department.If you need technical assistance or should it be necessary to returnyour product for servicing, call 1-800-722-3262. If parts arerequired to repair the product at your facility, call 1-949-859-8999and ask for the Parts Department
When sending your instrument in for repair, complete the form inthe back of this manual.
User Manual 1260-35
Module Specification 1-4
This page was left intentionally blank.
User Manual 1260-35
Installation Instructions 2-1
Chapter 2
INSTALLATION INSTRUCTIONS
Unpacking andInspection
1. Before unpacking the switching module, check the exterior ofthe shipping carton for any signs of damage. All irregularitiesshould be noted on the shipping bill.
2. Remove the instrument from its carton, preserving the factorypackaging as much as possible.
3. Inspect the switching module for any defect or damage.Immediately notify the carrier if any damage is apparent.
4. Have a qualified person check the instrument for safety beforeuse.
CAUTION
Proper ESD handling procedures must always beused when packing, unpacking or installing any 1260Series cards. Failure to do so may cause damage tothe unit.
ReshipmentInstructions
1. Use the original packing material when returning the switchingmodule to Racal Instruments for servicing. The originalshipping carton and the instrument's plastic foam will providethe necessary support for safe reshipment.
2. If the original packing material is unavailable, wrap theswitching module in plastic sheeting and use plastic sprayfoam to surround and protect the instrument.
3. Reship in either the original or a new shipping carton.
User Manual 1260-35
Installation Instructions 2-2
Option 01Installation
Installation of the Option 01 to the 1260-35 is described in theInstallation section of the 1260 Series VXI Switching CardsManual.
ModuleInstallation
Installation of the 1260-35 Switching Module into a VXI mainframe,including the setting of DIP switches, is described in theInstallation section of the 1260 Series VXI Switching CardsManual. Configuration of the PCBA and setting of the DIP switchesSW1-5 and SW1-6 are described in the following sections.
1260-35 ID Byte Each configuration responds to different sets of values for<channel number>. The set of values the 1260-35 responds to iscontrolled by switch 5 on DIP switch 51 on the PCB. The switchsettings that correspond to the two configurations are as follows:
Configuration S1 Switch 5 S1 Switch 6
Four-wire Off Off
Two-wire On Off
Configuration The 1260-35 Scanner~u1tiplexer is a user configurable switchingmodule. Ten different configurations are available as follows:
1) Sixteen 1 x 6 two-wire scanner/multiplexers, P/N 404944-206
2) Eight 1 x 6 four-wire scanner/multiplexers, P/N 404944406
3) Eight 1 x 12 two-wire scanner/multiplexers, P/N 404944-212
4) Four 1 x 12 four-wire scanner/multiplexers, P/N 404944-412
5) Four 1 x 24 two-wire scanner/multiplexers, P/N 404944-224
6) Two 1 x 24 four-wire scanner/multiplexers, P/N 404944-424
7) Two 1 x 48 two-wire scanner/multiplexers, P/N 404944-248
8) One 1 x 48 four-wire scanner/multiplexers, P/N 404944448
9) One 1 x 96 two-wire scanner/multiplexers, P/N 404944-296
10) One 1 x 192 one-wire scanner/multiplexers, P/N 404944
Unless otherwise specified, the 1260-35 is shipped from thefactory in the 1 x 192 single wire configuration. Table 2-1 gives the
User Manual 1260-35
Installation Instructions 2-3
necessary information to configure the module into the otherpossible configurations
Table 2-1, 1260-35 Jumper Installation
An X indicates a jumper is to be fitted. An (X) indicates the jumper is optional depending onwhether access to the analog bus is required. A blank indicates no jumper is to be fitted.
16(1x6)2-wire
8(1x6)4-wire
8(1x12)2-wire
4(1x12)4-wire
4(1x24)2-wire
2(1x24)4-wire
2(1x48)2-wire
1(1x48)4-wire
1(1x96)2-wire
W2A, B (X) (X) (X)
W3A, B X X X X X X X
W4A, B X X X X X
W5A, B X X X X X X X
W6A, B X X X
W7A, B X
W8A, B X X X X X X X
W9A, B X X X X X
W10A, B X X X X X X X
W11A, B 1(1x192) 1-WIRE ONLY---> X
W12A,B X X X X X X X
W13A, B X X X X X
W14A, B X X X X X X X
W15A, B X
W16A, B X X X
W17A, B X X X X X X X
W18A, B X X X X X
W19A, B X X X X X X X
W20A, B (X) (X) (X)
User Manual 1260-35
Installation Instructions 2-4
Analog Bus In most of the above configurations, the 1260-35 may be userconfigured to access an analog bus (refer to Figure 3-1). Theanalog bus allows internal expansion for the configuration of largerscanner/multiplexers than the module may achieve alone, byproviding access to a common bus channel which may be daisychained to other modules via the front panel.
To connect the module to the analog bus, install jumpers W2A,W2B, W20A, and W20B.
User Manual 1260-35
Module Specific Syntax 3-1
Chapter 3
MODULE SPECIFIC SYNTAX
1260-35 ModuleSpecific Syntax
The Module Specific Syntax for the 1260-35 is required in the useof the OPEN and CLOSE commands. It will also appear in dataoutput by the Master in response to the PDATAOUT and PSETUPcommands.
Syntax The Module Specific Syntax for the 1260-35 SignalMultiplexer/Scanner module is as follows:
OPEN <module address>.<channel>[;<module address>. <channel>]
where <module address> is the switch card address. <channel> is the relay to be closed to connect an input to the output.
Note that Channels remain closed until opened by an OPENcommand, RESET command, VXI hard or soft reset, or power-off.
NOTE
The <module address> used here is NOT the VXIbusdefined logical address of the 1260 Series Master. Itis peculiar to the 1260 Series and describes theswitching module in relation to the Master. Thisaddress corresponds to the binary value of the switchsetting of SW1 on the switching module PCB.
The range of values for <channel> is:
One-wire 00-96Two-wire 00-95Four-wire 00-47
The actual mapping of number to connector pins is given in Table3-1. Figure 3-1 shows the physical location of the variousconnector pins.
User Manual 1260-35
Module Specific Syntax 3-2
Example:
OPEN 3.02
This open command will open channel 2 on the module at switchcard address 3
CLOSE Command The Module Specific Syntax for the CLOSE command is the sameas for the OPEN command.
PSETUPCommand
The PSETUP command causes the specified module setup to betransmitted to the VXI Controller. The syntax used is:
PSETUP <module address>[;<module address>] [;<moduleaddress>] where <module address> is the address.
The responses to the PSETUP command for the 1260-35Multiplexer/Scanner is as follows:
1260-35: Two-wire
<module address>. 1260-35B, Two-wire Scanner/Multiplexer Module<module address>. BBM<module address>.END
1260-35: Four-wire
<module address>. 1260-35A, Four-wire Scanner/Multiplexer Module<module address>. BBM<module address>.END
The response to the PSETUP command consists of a header onthe first line. The header describes the model number followed byan A or B designating four or two-wire, respectively. The next linedesignates the setup mode for scanning which, by default, isBreak-Before-Make (BBM). The last line containing the "END"characters denotes no more information to report.
PDATAOUT The PDATAOUT command causes the specified module totransmit the CLOSED state of the relays within the switching
User Manual 1260-35
Module Specific Syntax 3-3
Command module to the 1260 Controller. The syntax used is:
PDATAOUT <module address>[.<module address>] [;<module address>]…..
The responses to the PDATAOUT command is as follows:
1260-35: Two-wire
<module address>. 1260-3 SB Two-wire Scanner/Multiplexer Module <module address>. <channel>[,<channel>] [,<channel>] <module address>.END
1260-35 Four-wire
<module address>. 1 260-35A Four-wire Scanner/Multiplexer Module<module address>. <channel>[,<channel>] [,<channel>]<module address>.END
The response to the PDATAOUT command consists of a headeron the first line as with the PSETUP response. The next linedetails the channels currently closed on the module and is blankwhen no channels are closed. Again, the last line is denoted by the"END" string of characters.
Operation InSingle-Wire Mode
The 1260-35 is delivered with all jumpers installed (refer to Table2-1). In this configuration, the module is a 1 x 96 two-wiremultiplexer (refer to Figure 3-1).
Channel 97 is a single pole, double throw (SPDT) relay with itscommon channel connected to J202, pin B2. The normally closed(NC) contact is connected to the "LO" side of the two-wirecommon bus, and the normally open (NO) contact is connected tothe "HI" side of the common bus.
The common output of channel 96 is the single channel of the 192x 1 multiplexer, and the 96 HI and 96 LO connections make up the192 channels. By closing the appropriate channel (0-95) andopening or closing channel 96. a 192 x 1 multiplexer is achieved.
Example:
CLOSE 3.46CLOSE 3.96
This would correct J202 pin B2 to J202 pin A4
Table 3-1, 1260-35 Channel Closure
User Manual 1260-35
Module Specific Syntax 3-4
channel interconnect for 1, 2 and 4-wire modes.
1-wire mode:
<channel> <channel> output <channel> input(channel 96 open)0 thru 95 always J202- B2 (see 2-wire mode channels 0-95 input pins b-side of channel)(channel 96 closed)0 thru 95 always J202- B2 (see 2-wire mode channels 0-95 input pins a-side of channel)Thus, a one 1 x 191 1-wire mode is acheived.
2-wire mode:channel> <channel> output pins to <channel> input pins
a / b a / b(HI) (Lo) (HI) (LO)
0 J200- A30 / B30 J200- A29 / B291 J200- A30 / B30 J200- A28 / B282 J200- A30 / B30 J200- A27 / B273 J200- A30 / B30 J200- A26 / B264 J200- A30 / B30 J200- A25 / B255 J200- A30 / B30 J200- A24 / B246 J200- A23 / B23 J200- A22 / B227 J200- A23 / B23 J200- A21 / B218 J200- A23 / B23 J200- A20 / B209 J200- A23 / B23 J200- A19 / B1910 J200- A23 / B23 J200- A18 / B1811 J200- A23 / B23 J200- A17 / B1712 J200- A16 / B16 J200- A15 / B1513 J200- A16 / B16 J200- A14 / B1414 J200- A16 / B16 J200- A13 / B1315 J200- A16 / B16 J200- A12 / B1216 J200- A16 / B16 J200- A11 / B1117 J200- A16 / B16 J200- A10 / B1018 J200- A9 / B9 J200- A8 / B819 J200- A9 / B9 J200- A7 / B720 J200- A9 / B9 J200- A6 / B621 J200- A9 / B9 J200- A5 / B522 J200- A9 / B9 J200- A4 / B423 J200- A9 / B9 J200- A3 / B324 J202- A30 / B30 J202- A29 / B2925 J202- A30 / B30 J202- A28 / B2826 J202- A30 / B30 J202- A27 / B2727 J202- A30 / B30 J202- A26 / B2628 J202- A30 / B30 J202- A25 / B2529 J202- A30 / B30 J202- A24 / B24
User Manual 1260-35
Module Specific Syntax 3-5
Table 3-1, 1260-35 Channel Closure (continued)
30 J202 A23 I B23 J202 A22 / B2231 J202 A23 / B23 J202 A21 / B2132 J202 A23 / B23 J202 A20 / B2033 J202 A23 / B23 J202 A19 / B1934 J202 A23 / B23 J202 A18 / B1835 J202 A23 / B23 J202 A17 / B1736 J202 A16 / B16 J202 A15 / B1537 J202 A16 / B16 J202 A14 / B1438 J202 A16 / B16 J202 A13 / B1339 J202 A16 / B16 J202 A12 / B1240 J202 A16 / B16 J202 A11 / B1141 J202 A16 / B16 J202 A10 / B1042 J202 A9 / B9 J202 A8 / B843 J202 A9 / B9 J202 A7 / B744 J202 A9 / B9 J202 A6 / B645 J202 A9 / B9 J202 AS / B546 J202 A9 / B9 J202 A4 / B447 J202 A9 / B9 J202 A3 / B348 J201 A30 / B30 J201 A29 / B2949 J201 A30 / B30 J201 A28 / B2850 J201 A30 / B30 J201 A27 / B2751 J201 A30 / B30 J201 A26 / B2652 J201 A30 / B30 J201 A25 / B2553 J201 A30 / B30 J201 A24 / B2454 J201 A23 / B23 J201 A22 / B2255 J201 A23 / B23 J201 A21 / B2156 J201 A23 / B23 J201 A20 / B2057 J201 A23 / B23 J201 A19 / B1958 J201 A23 / B23 J201 A18 / B1859 J201 A23 / B23 J201 A17 / B1760 J201 A16 / B16 J201 A15 / B1561 J201 A16 / B16 J201 A14 / B1462 J201 A16 / B16 J201 A13 / B1363 J201 A16 / B16 J201 A12 / B1264 J201 A16 / B16 J201 A11 / B1165 J201 A16 / B16 J201 A10 / B1066 J201 A9 / B9 J201 A8 / B867 J201 A9 / B9 J201 A7 / B768 J201 A9 / B9 J201 A6 / B669 J201 A9 / B9 J201 AS / B570 J201 A9 / B9 J201 A4 / B471 J201 A9 / B9 J201 A3 / B372 J203 A30 / B30 J203 A29 / B2973 J203 A30 / B30 J203 A28 / B2874 J203 A30 / B30 J203 A27 / B2775 J203 A30 / B30 J203 A26 / B2676 J203 A30 / B30 J203 A25 / B2577 J203 A30 / B30 J203 A24 / B324
User Manual 1260-35
Module Specific Syntax 3-6
Table 3-1, 1260-35 Channel Closure (continued)
78 J203 A23 / B23 J203 A22 / B2279 J203 A23 / B23 J203 A21 / B2180 J203 A23 / B23 J203 A20 / B2081 J203 A23 / B23 J203 A19 / B1982 J203 A23 / B23 J203 A18 / B1883 J203 A23 / B23 J203 A17 / B1784 J203 A16 / B16 J203 A15 / B1585 J203 A16 / B16 J203 A14 / B1486 J203 A16 / B16 J203 A13 / B1387 J203 A16 / B16 J203 A12 / B1288 J203 A16 / B16 J203 A11 / B1189 J203 A16 / B16 J203 A10 / B1090 J203 A9 / B9 J203 A8 / B891 J203 A9 / B9 J203 A7 / B792 J203 A9 / B9 J203 A6 / B693 J203 A9 / B9 J203 A5 / B594 J203 A9 / B9 J203 A4 / B495 J203 A9 / B9 J203 A3 / B3
96 (not used in 2-wire mode)
4-wire mode:
<channel> refer to the following 2-wirechannels for the input/outputpins
<channel> refer to the following 2-wire channels for theinput/output pins
0 0,48 24 24,721 1,49 25 25,732 2,50 26 26,743 3,51 27 27,754 4, 52 28 28,765 5,53 29 29,776 6, 54 30 30,787 7,55 31 31,798 8,56 32 32,809 9 , 57 33 33,8110 10, 58 34 34,8211 11,59 35 35,8312 12,60 36 36,8413 13,61 37 37,8514 14,62 38 38,8615 15,63 39 39,8716 16, 64 40 40,8817 17,65 41 41,8918 18,66 42 42,9019 19,67 43 43,9120 20,68 44 44,9221 21,69 45 45,9322 22,70 46 46,9423 23,71 47 47,95
96 (not used in 4-wire mode)
User Manual 1260-35
Module Specific Syntax 3-7Figure 3-1, 1260-35 Block Diagram
K 1 2C
H11
K 1 1C
H10
K 1 0C
H9
K 9C
H8
K 8C
H7
K 7C
H6
K 1 3C
H12
K 1 4C
H13
K 1 5C
H14
K 1 6C
H15
K 1 7C
H16
K 1 8C
H17
K 3 6C
H35
K 3 5C
H34
K 3 4C
H33
K 3 3C
H32
K 3 2C
H31
K 3 1C
H30
K 3 7C
H36
K 3 8C
H37
K 3 9C
H38
K 4 0C
H39
K 4 1C
H40
K 4 2C
H41
K 6 0C
H59
K 5 9C
H58
K 5 8C
H57
K 5 7C
H56
K 5 6C
H55
K 5 5C
H54
K 6 1C
H60
K 6 2C
H61
K 6 3C
H62
CH
63K 6 4 K 6 5
CH
64
K 6 6C
H65
K 8 4C
H83
K 8 3C
H82
K 8 2C
H81
K 8 1C
H80
K 8 0C
H79
K 7 9C
H78
K 8 5C
H84
K 8 6C
H85
K 8 7C
H86
CH
87K 8 8 K 8 9
CH
88
K 9 0C
H89
K 6C
H5
K 5C
H4
KK 4C
H3
KK 3C
H2
K 2C
H1
K 1C
H0
K 1 9C
H18
K 2 0C
H19
K 2 1C
H20
CH
21K 2 2 K 2 31
CH
22
K 2 4C
H23
K 3 0C
H29
K 2 9C
H28
KK 2 8C
H27
KK 2 7C
H26
K 2 6C
H25
K 2 5C
H24
K 4 3C
H42
K 4 4C
H43
K 4 5C
H44
CH
45K 4 6 K 4 7
CH
46
K 4 8C
H47
K 5 4C
H53
K 5 3C
H52
KK 5 2C
H51
KK 5 1C
H50
K 5 0C
H49
K 4 9C
H48
K 6 7C
H66
K 6 8C
H67
K 6 9C
H68
CH
69K 7 0 K 7 1
CH
70
K 7 2C
H71
K 7 8C
H77
K 7 7C
H76
KC
H75
K 7 6 KC
H74
K 7 5 K 7 4C
H73
K 7 3C
H72
K 9 1C
H90
K 9 2C
H91
K 9 3C
H92
CH
93K 9 4 K 9 5
CH
94
K 9 6C
H95
W4A
W4B
W9A
W9B
W13
B
W18
A
W18
B
1/24
CO
M 2
CO
M 3
CO
M 6
CO
M 7
1/24
W7A
W7B
1/96
CO
M 1
0C
OM
11
1/24
W15
A
W15
B
1/96
CO
M 1
4C
OM
15
1/24
W3A
W3B
W5B
W5A
W2B
W2A
1/12
1/12
ANAL
OG
BUS 1
W6B
W6A
1/48
W8A
W8B
W10
B
W10
A
1/12
1/12
W11
B
W11
A
K97
CO
M 1
71-
WIR
EC
H96
ANAL
OG
BUS 2
W20
B
W20
A
W12
A
W12
B W14
B
W14
A
1/12
1/12
W16
B
W16
A
W17
AW
19B
W17
BW
19A
1/12
1/12
1/48
AB
US
1C
OM
1C
OM
4C
OM
5C
OM
8A
BU
S 2
CO
M 9
CO
M 1
2C
OM
13
CO
M 1
6
W13
A
User Manual 1260-35
Module Specific Syntax 3-8
Figure 3-2, 1260-35 Pin Connections, Front View
User Manual 1260-35
Drawings 4-1
Chapter 4
DRAWINGS
404944 Final Assy, 1260-35 (IDC Connectors) ...................................................4-3
404944-001 Final Assy, 1260-35A (Crimp Connectors) .............................................4-4
401989 PCB Assy, 1260-35..................................................................................4-5
431989 Schematic, 1260-35..................................................................................4-7
401992 PCB Assy, 1260-35D.............................................................................4-24
431992 Schematic, 1260-35D.............................................................................4-25
User Manual 1260-35
Drawings 4-2
User Manual 1260-35
Drawings 4-3
NO
TES:
DRA
FT
T.D
AVI
S
F
12
45
67
8
12
3
4049
44
404944
RELE
ASE
D P
ER D
RN N
O. 1
338
1/1
G
45
6
PRO
PRIE
TARY
NO
TICE
TITLE
SIZE
CA
GE
CO
DE
78
3
H G
G
1
F E D C B A
H G F E D C B
REVI
SIO
NS
THIS
DO
CUM
ENT
AN
D T
HE T
ECHN
ICAL
DAT
A HE
REIN
DIS
CLO
SED
ARE
PRO
PRIE
TARY
TO
RAC
AL IN
STRU
-M
ENTS
IN
C.
AND
SHA
LL N
OT,
WITH
OUT
THE
EX-
PRES
S W
RITT
EN P
ERM
ISSI
ON
OF
RAC
AL IN
STRU
-M
ENTS
INC
. BE
USED
, REL
EASE
D O
R D
ISC
LOSE
D IN
WHO
LE O
R IN
PAR
T, O
R US
ED T
O S
OLIC
IT Q
UOTA
-TIO
NS
FRO
M A
CO
MPE
TITIV
E SO
URC
E O
R US
ED F
OR
MAN
UFAC
TURE
BY
AN
YON
E O
THER
THA
N R
ACAL
IN-
STRU
MEN
TS IN
C. T
HE I
NFO
RMAT
ION
HER
EON
HAS
BEEN
DEV
ELO
PED
AT
PRIV
ATE
EXP
ENSE
, AN
D M
AYO
NLY
BE
USE
D F
OR
PUR
POSE
S O
F E
NG
INEE
RIN
GEV
ALUA
TION
AN
D F
OR
INC
ORP
ORA
TION
INTO
TEC
H-N
ICAL
SPE
CIF
ICAT
ION
S A
ND
OTH
ER D
OC
UMEN
TSW
HIC
H S
PEC
IFY
PRO
CUR
EMEN
T O
F PR
OD
UCTS
FRO
MRA
CAL
INST
RUM
ENTS
INC
.
Rac
al I
nstru
me
nts,
Inc
.4
Go
od
yea
r St.,
Irvin
e,C
A.9
2718
-200
2
REV
.D
OC
UM
ENT
NU
MBE
R
SHT.
OF
SCA
LEC
ALC
.WT
ACT.W
T
2179
32
DES
CRI
PTIO
ND
ATE
APP
ROVE
DRE
V.
D
DOC.NO.
A B C D E
REVI
SED
PER
EO
NO
. 208
09J.
ROBI
NSO
N
9-26
-90
REVI
SED
PER
EO
NO
. 208
72
9405
05
9405
05J.
ROBI
NSO
N
REVI
SED
PER
EO
NO
.
J.RO
BIN
SON
J.RO
BIN
SON
J.RO
BIN
SON
REVI
SED
PER
EO
NO
. 221
69
REVI
SED
PER
EO
NO
. 227
66
9405
05
9405
05
9405
05
AUS
MA
N
AUS
MA
N
AUS
MA
N
AUS
MA
N
AUS
MA
N
1260
-35,
2W, 1
X96
SC
MUX
,IDC
REVI
SED
& R
EDRA
WN
PER
EO
NO
. 230
43
SL95
0209
AUS
MA
N
PART
OF
ITEM
17
DO
NO
T SH
IP O
R ST
ORE
NEA
R ST
RON
G
ELEC
TRO
STA
TIC ,
ELEC
TRO
MA
GN
ETIC
,M
AG
NET
IC O
R R
AD
IOA
CTIV
E FI
ELD
S
REF
16 15 319
A/R
SCAL
E: 2
/1
REF
REF
2 RE
QD9
HAN
DLE
PAR
T O
F ITE
M 1
6 (TO
P)ITE
M 1
5 (B
OT) FL
AT H
EAD
SC
REW
,PA
RT O
F ITE
M 1
7 AP
PLY
LOC
TITE
"TO
P"
"BO
TTO
M"
PLAT
E, P
ART
OF
ITEM
S 15
, 16
17 17
MO
UNTIN
G B
LOC
KPA
RT O
F ITE
MS
15, 1
6
1
0
8
1
21
LABE
L, P
ART
OF
ITEM
31
RAC
AL IN
STRU
MEN
TS L
OG
O (T
OP)
VXI S
YMBO
L (B
OT)
31
765432
LOGICAL ADDRESS SELECT
1
MSB
LSB
1
0
4321
INTERRUPT SELECT
LSB
MSB
N/A
A/R
BEAR
ING
, PAR
TO
F ITE
MS
15, 1
6
1
5.
27
11 13
2 RE
QD
24
REF
27
111.
00 ±
.12
1
296.
1.00
±.1
2
2.
PART
OF
ITEM
35
.70
±.1
2
31 2 4 5 6
4. C
ON
NEC
T C
ABL
E FR
OM
ITEM
1 T
O IT
EM 3
AS
SHO
WN
. 5.
APP
LY L
OC
TITE
SPA
RIN
GLY
. D
O N
OT
ALL
OW
CO
NTA
CT
WITH
EJE
CTO
R H
AN
DLE
S ITE
MS
1
5 (B
OT)
AN
D 1
6(TO
P).
6. L
OC
ATE
APP
ROPR
IATE
VXI
LA
BEL
WH
ERE
SHO
WN
.
REF
EREN
CE
9214
10 F
OR
SPEC
IFIC
LA
BEL
IN
FORM
ATIO
N.
2 3 4 OPEN
CLOSE
5 6
12 LOCAL BUS LINES
2.
REF
13 24
1
0
6 5 4 3
3 RE
QD
2 1
LSB MSB
(Configurable cards only)
1260 CARD ADDR
8421ID
BYTE
PART
OF
ITEM
35
4.
196
REQ
D3
19
2334
6
BB
1. D
ISC
ARD
UN
USED
HA
RDW
ARE
IN IT
EM 1
7. 2.
AFF
IX L
ABE
LS A
S SH
OW
N, A
LIG
N L
ABE
L TE
XT
WITH
APP
ROPR
IATE
SW
ITCH
AC
TUA
TORS
. 3.
IN
CLU
DE
SHIP
PIN
G K
IT, IT
EM 5
IN B
OX
WITH
ASS
Y.
DET
AIL
'A'
DET
AIL
'A'
24
SCAL
E: 1
/2BO
TTO
M V
IEW
VIEW
B-B
User Manual 1260-35
Drawings 4-4
NO
TES:
DRA
FT
T.D
AVI
S
12
45
67
8
12
3
1/1
4049
44-0
01
404944-001
RELE
ASE
D P
ER D
RN N
O. 1
491
45
6
PRO
PRIE
TARY
NO
TICE
TITLE
SIZE
CA
GE
CO
DE
78
3
H G
E
1
F E D C B A
H G F E D C B
REVI
SIO
NS
THIS
DO
CUM
ENT
AN
D T
HE
TEC
HN
ICA
L D
ATA
HER
EIN
DIS
CLO
SED
ARE
PRO
PRIE
TARY
TO
RA
CA
L IN
STRU
-M
ENTS
IN
C.
AN
D S
HA
LL N
OT,
WITH
OUT
TH
E EX
-PR
ESS
WRI
TTEN
PER
MIS
SIO
N O
F RA
CA
L IN
STRU
-M
ENTS
INC
. BE
USED
, REL
EASE
D O
R D
ISC
LOSE
D IN
WH
OLE
OR
IN P
ART
, OR
USED
TO
SO
LIC
IT Q
UOTA
-TIO
NS
FRO
M A
CO
MPE
TITIV
E SO
URC
E O
R US
ED F
OR
MA
NUF
AC
TURE
BY
AN
YON
E O
THER
TH
AN
RA
CA
L IN
-ST
RUM
ENTS
INC
. TH
E IN
FORM
ATIO
N H
EREO
N H
AS
BEEN
DEV
ELO
PED
AT
PRIV
ATE
EXP
ENSE
, AN
D M
AY
ON
LY B
E U
SED
FO
R P
URPO
SES
OF
EN
GIN
EERI
NG
EVA
LUA
TION
AN
D F
OR
INC
ORP
ORA
TION
INTO
TEC
H-
NIC
AL
SPE
CIF
ICA
TION
S A
ND
OTH
ER D
OC
UMEN
TSW
HIC
H S
PEC
IFY
PRO
CUR
EMEN
T O
F PR
OD
UCTS
FRO
MRA
CA
L IN
STRU
MEN
TS IN
C.
Rac
al I
nstru
me
nts,
Inc
.4
Go
od
yea
r St.,
Irvin
e,C
A.9
2718
-200
2
REV
.D
OC
UM
ENT
NU
MBE
R
SHT.
OF
SCA
LEC
ALC
.WT
ACT.W
T
2179
32
DES
CRI
PTIO
ND
ATE
APP
ROVE
DRE
V.
D
DOC.NO.
A B C
REVI
SED
PER
EO
NO
. 223
74
D E
REVI
SED
PER
EO
NO
.
J.RO
BIN
SON
10-1
6-91
Z.H
.B94
0126
9405
06
REVI
SED
PER
EO
NO
.
REVI
SED
PER
EO
NO
. 227
67
REVI
SED
PER
EO
NO
.
J.RO
BIN
SON
9405
06RE
VISE
D &
RED
RAW
N P
ER E
O N
O. 2
3045
SL
950
209
AUS
MA
N
J.R.
AUS
MA
N
1260
-35A
,2W
,1X
96 S
C M
UX,C
RMP
AUS
MA
N
PART
OF
ITEM
17
DO
NO
T SH
IP O
R ST
ORE
NEA
R ST
RON
GEL
ECTR
OST
ATIC
, EL
ECTR
OM
AG
NET
IC,
MA
GN
ETIC
OR
RA
DIO
AC
TIVE
FIEL
DS
REF
16 15 319
A/R
SCAL
E: 2
/1
REF
REF
2 RE
QD9
HAN
DLE
PAR
T O
F ITE
M 1
6 (TO
P)ITE
M 1
5 (B
OT) FL
AT H
EAD
SC
REW
,PA
RT O
F ITE
M 1
7 AP
PLY
LOC
TITE
"TO
P"
"BO
TTO
M"
PLAT
E, P
ART
OF
ITEM
S 15
, 16
17 17
MO
UNTIN
G B
LOC
KPA
RT O
F ITE
MS
15, 1
6
1
0
8
1
21
LABE
L, P
ART
OF
ITEM
31
RAC
AL IN
STRU
MEN
TS L
OG
O (T
OP)
VXI S
YMBO
L (B
OT)
31
765432
LOGICAL ADDRESS SELECT
1
MSB
LSB
1
0
4321
INTERRUPT SELECT
LSB
MSB
N/A
A/R
BEAR
ING
, PAR
TO
F ITE
MS
15, 1
6
1
5.
27
11 13
2 RE
QD
24
REF
27
111.
00 ±
.12
296.
1.00
±.1
2
2.
PART
OF
ITEM
35
.70
±.1
2
31 2 4 5
4. C
ON
NEC
T C
ABLE
FRO
M IT
EM 1
TO
ITEM
3 A
S SH
OW
N.
5. A
PPLY
LO
CTIT
E SP
ARIN
GLY
. D
O N
OT
ALLO
W
C
ON
TAC
T W
ITH E
JEC
TOR
HAN
DLE
S ITE
MS
1
5 (B
OT)
AN
D 1
6(TO
P).
6. L
OC
ATE
APPR
OPR
IATE
VXI
LAB
EL W
HERE
SHO
WN
.
REF
EREN
CE
9214
10 F
OR
SPEC
IFIC
LAB
EL
INFO
RMAT
ION
.
6 1 2 3 4 OPEN
CLOSE
5 6
12 LOCAL BUS LINES
2.
REF
13 24
1
0
6 5 4 3
3 RE
QD
2 1
LSB MSB
(Configurable cards only)
1260 CARD ADDR
8421ID
BYTE
PART
OF
ITEM
35
4.
196
REQ
D3
19
2334
7
BB
1. D
ISC
ARD
UN
USED
HAR
DW
ARE
IN IT
EM 1
7. 2.
AFF
IX L
ABEL
S AS
SHO
WN
, ALIG
N L
ABEL
TEX
T
WITH
APP
ROPR
IATE
SW
ITCH
ACTU
ATO
RS.
3. I
NC
LUD
E SH
IPPI
NG
KIT,
ITEM
5 IN
BO
X W
ITH A
SSY.
DET
AIL
'A'
DET
AIL
'A'
24
SCAL
E: 1
/2BO
TTO
M V
IEW
VIEW
B-B
User Manual 1260-35
Drawings 4-5
User Manual 1260-35
Drawings 4-6
User Manual 1260-35
Drawings 4-7
User Manual 1260-35
Drawings 4-8
User Manual 1260-35
Drawings 4-9
User Manual 1260-35
Drawings 4-10
User Manual 1260-35
Drawings 4-11
User Manual 1260-35
Drawings 4-12
User Manual 1260-35
Drawings 4-13
User Manual 1260-35
Drawings 4-14
User Manual 1260-35
Drawings 4-15
User Manual 1260-35
Drawings 4-16
User Manual 1260-35
Drawings 4-17
User Manual 1260-35
Drawings 4-18
User Manual 1260-35
Drawings 4-19
User Manual 1260-35
Drawings 4-20
User Manual 1260-35
Drawings 4-21
User Manual 1260-35
Drawings 4-22
User Manual 1260-35
Drawings 4-23
User Manual 1260-35
Drawings 4-24
User Manual 1260-35
Drawings 4-25
User Manual 1260-35
Drawings 4-26
User Manual 1260-35
Drawings 4-27
User Manual 1260-35
Drawings 4-28
User Manual 1260-35
Drawings 4-29
User Manual 1260-35
Drawings 4-30
User Manual 1260-35
Parts List 5-1
Chapter 5
PARTS LIST
404944 Final Assembly, 1260-35 (IDC Connector) 5-3
404975 Shipping Kit, 1260-35 5-4
404944-001 Final Assembly, 1260-35A (Crimp Connectors) 5-5
404975-001 Shipping Kit, 1260-35A 5-6
401989 PCB Assy, 1260-35 5-7
401992 PCB Assy, 1260-35D 5-10
List of Suppliers 5-11
User Manual 1260-35
Parts List 5-2
This page was left intentionally blank.
User Manual 1260-35
Parts List 5-3
User Manual 1260-35
Parts List 5-4
User Manual 1260-35
Parts List 5-5
User Manual 1260-35
Parts List 5-6
User Manual 1260-35
Parts List 5-7
User Manual 1260-35
Parts List 5-8
User Manual 1260-35
Parts List 5-9
User Manual 1260-35
Parts List 5-10
User Manual 1260-35
Parts List 5-11
User Manual 1260-35
Parts List 5-12
This page was left intentionally blank.
User Manual 1260-35
Optional Harness Assemblies 6-1
Chapter 6
OPTIONAL HARNESS ASSEMBLIES
The following harness assemblies are used to connect Racal Instruments Model 1260-35 toFreedom Series Test Receiver Interfaces.
Each harness documentation consists of an assembly drawing, parts list, system wire list and wirelist.
407280 Virginia Panel, Inc. Series VP90 Interface Harness
407281 TTI Testron, Inc. Interface Harness
For more information on Racal Instruments complete line of Test Receivers Interface solution,contact your Sales Representative.
User Manual 1260-35
Optional Harness Assemblies 6-2
This page was left intentionally blank.
User Manual 1260-35
Optional Harness Assemblies 6-3
6
1.7
MA
X3
PLC
S
AR
6 PL
CS
11.0
±1.
0 2
PLC
S
39.0
±2.
0 3
PLC
S
6 7
3
7
109AR
10 P
LCS
23
PLC
S
PIN
1
2.5
±.2
2.0
±.2
PIN
1
PIN
1
3
AR2.
0±
.2
3 RE
QD
4072
80 R
EV.
2.5
±.2
36.0
±2.
0
7
SEE
WIR
E LI
ST F
OR
CO
NTA
CT
ASS
IGN
MEN
TS A
ND
CO
NN
ECTIO
NS.
2 3 6 7 85.M
ATIN
G IT
A C
ON
NEC
TOR
FOR
J102
IS V
IRG
INIA
PA
NEL
P/N
510
108
101.
USE
ITA
PIN
P/N
610
110
108
.
MA
TING
ITA
CO
NN
ECTO
R FO
RJ1
00 A
ND
J10
1 IS
VIR
GIN
IAPA
NEL
P/N
510
108
126
. USE
ITA P
IN P
/N 6
10 1
10 1
08.
1
INK
STA
MP
"J--
-" A
PPRO
XI-
MA
TELY
WH
ERE
SHO
WN
.
APP
LY P
ROTE
CTIV
E C
OA
TING
(ITEM
5) O
VER
MA
RKIN
G.
1. 4.
PLA
CE
APP
ROPR
IATE
SIZ
E C
LEA
RSH
RIN
K TU
BIN
G O
VER
MA
RKIN
G.
TERM
INA
TE B
RAID
ED S
LEEV
ING
(ITEM
6) A
T IN
DIC
ATE
D E
ND
SW
ITH B
LAC
K SH
RIN
K TU
BIN
G.
PLA
CE
SHRI
NK
TUBI
NG
(ITEM
8)
APP
ROXI
MA
TELY
WH
ERE
SHO
WN
.
2
2
3 4
PLC
SFA
R SI
DE
PIN
1
2
9.EN
CLO
SE C
ABL
ES IN
SIN
GLE
BA
G.
PIN
1
MA
RK "4
0728
0" A
ND
LA
TEST
REVI
SIO
N O
N A
PPRO
PRIA
TESI
ZE S
HRI
NK
TUBI
NG
APP
ROXI
-M
ATE
LY W
HER
E SH
OW
N.
PIN
1
PIN
1
8
4A
R
8
J1
J2
(P2)
J102 (P2)
J1
J2J3
J1
J3
J100
J101
J2
(P2)
(P2)
J200
J203
(P3)
(P1)
J202
J201
(P1)
(P1)
(P1)
P2
DWG
NO
.RE
V.
SCAL
ESH
EET
OF
ACT.W
TC
ALC
.WT
PRO
PRIE
TARY
NO
TICE
SIZE
REV
DES
CRIP
TIO
ND
ATE
1
APP
RO
VED
REV
ISIO
NS
AM
N 0
4/12
/99
NO
TES:
A B
ZON
E
CD
REV
ISED
PER
EO
NO
. 2
53
46
REV
ISED
PER
EO
NO
. 2
57
59
db
SEE
SEPA
RATE
PA
RTS
LIST
TITLE
4 G
oo
dye
ar S
t.,Irv
ine
,CA
.927
18-2
002
A
D ABC
12
34
13
4072
80
AM
S 11
/17/
94
11
-08
-94
4
CAG
E C
ODE
NO
NE
REL
EASE
D P
ER D
RN
NO
. 1
54
1
THIS
DO
CU
MEN
T A
ND
TH
E TE
CH
NIC
AL
DA
TA H
EREO
N D
ISC
LOSE
D A
RE
PRO
PRIE
TARY
TO R
AC
AL
INST
RU
MEN
TS IN
C. A
ND
SH
ALL
NO
T, W
ITH
OU
T TH
E EX
PRES
S W
RIT
TEN
PERM
ISSI
ON
O
F RA
CA
L IN
STRU
MEN
TS IN
C. B
E U
SED
, R
ELEA
SED
OR D
ISC
LOSE
DIN
WH
OLE
OR IN
PA
RT,
O
R U
SED
TO
SO
LIC
IT Q
UO
TATI
ON
FRO
M A
CO
MPE
TITI
VE
SOU
RC
E O
R U
SED
FO
R M
AN
UFA
CTU
RE
BY A
NYO
NE
OTH
ER T
HA
N RA
CA
L IN
STRU
MEN
TSIN
C. TH
E IN
FORM
ATI
ON
H
EREO
N H
AS
BEEN
DEV
ELO
PED
A
T PR
IVA
TE E
XPE
NSE
,A
ND
M
AY
ON
LY B
E U
SED
FO
R P
URPO
SES
OF
ENG
INEE
RIN
G EV
ALU
ATI
ON
A
ND
FO
RIN
CO
RPO
RA
TIO
N IN
TO T
ECH
NIC
AL
SPEC
IFIC
ATI
ON
S A
ND
OTH
ER D
OC
UM
ENTS
W
HIC
HSP
ECIF
Y P
RO
CU
REM
ENT
OF
PRO
DU
CTS
FRO
M R
AC
AL
INST
RU
MEN
TS IN
C.
12
98
03
37
REV
. F
DWG. NO. REV.SH.
8
HA
RNES
S A
SSY,
1260
-35,
VP90
D407280
D
REV
ISED
PER
EO
NO
. 2
34
32
& R
EDRW
N
C D
98
04
29
J. R
OBI
NSO
N
LA 1
1-1
7-9
4
J. R
OBI
NSO
N
User Manual 1260-35
Optional Harness Assemblies 6-4
RACAL INSTRUMENTS INC.
Assembly 407280 HARNESS ASSY, 1260-35, VP90 Date 3/18/99 Revision D
# Component Description U/N Qty Reqd Ref1 405084 PCB ASSY, VP90 INTFC, 64CONTCT EA 1.000002 405085 PCB ASSY, VP90 INTFC, 96CONTCT EA 2.000003 407259 CABLE ASSY, IDC, 64COND,VP90 EA 3.000004 407258 CABLE ASSY, IDC, 64SPLT,VP90 EA 1.000005 910541 POLYURETHANE CONFORMAL COAT EA .000016 GRP-l10-l/2 TBGWOV- POY. 250ID-BLACK FT .000017 500005 TIE CORD NYLON FT .000018 500017 TBGSRK- POF. 500lD-BLACK FT .000019 M23053/5-109-4 TBGSRK- POF. 750ID-YELLOW FT .0000110 500104 TBGSRK- POF .750 ID-CLEAR FT .00001
User Manual 1260-35
Optional Harness Assemblies 6-5
User Manual 1260-35
Optional Harness Assemblies 6-6
User Manual 1260-35
Optional Harness Assemblies 6-7
User Manual 1260-35
Optional Harness Assemblies 6-8
User Manual 1260-35
Optional Harness Assemblies 6-9
User Manual 1260-35
Optional Harness Assemblies 6-10
User Manual 1260-35
Optional Harness Assemblies 6-11
User Manual 1260-35
Optional Harness Assemblies 6-12
9803
40 R
EV. F
DW
G N
O.
REV.
SCA
LESH
EET
OF
AC
T.W
TC
ALC
.WT
1
11
PRO
PRIE
TARY
NO
TICE
SIZE
DW
G. N
O.
SH REV
DES
CRI
PTIO
ND
ATE
APP
ROVE
D
REVI
SIO
NS
NO
TES:
REV.
ZON
E
REVI
SED
PER
EO
NO
.
D
4072
81
C
D
ARE
LEA
SED
PER
DRN
NO
. 154
111
/8/9
4D
B
BJR
95-
03-1
3TD
E
CRE
VISE
D P
ER E
O N
O. 2
5356
JR
9805
01
AB
12
34
1
1:1
34
C
HA
RNES
S A
SSY,
126
0-35
, TTI
AB
TITLE
4 G
oo
dye
ar S
t.,Irv
ine
,CA
.927
18-2
002
CA
GE
CO
DE
THIS
DO
CU
MEN
T A
ND
TH
E TE
CH
NIC
AL
DA
TA H
EREO
N D
ISC
LOSE
D A
RE
PRO
PRIE
TARY
TO R
AC
AL
INST
RU
MEN
TS IN
C. A
ND
SH
ALL
NO
T, W
ITH
OU
T TH
E EX
PRES
S W
RIT
TEN
PERM
ISSI
ON
O
F RA
CA
L IN
STRU
MEN
TS IN
C. B
E U
SED
, R
ELEA
SED
OR D
ISC
LOSE
DIN
WH
OLE
OR IN
PA
RT,
O
R U
SED
TO
SO
LIC
IT Q
UO
TATI
ON
FRO
M A
CO
MPE
TITI
VE
SOU
RC
E O
R U
SED
FO
R M
AN
UFA
CTU
RE
BY A
NYO
NE
OTH
ER T
HA
N RA
CA
L IN
STRU
MEN
TSIN
C. TH
E IN
FORM
ATI
ON
H
EREO
N H
AS
BEEN
DEV
ELO
PED
A
T PR
IVA
TE E
XPE
NSE
,A
ND
M
AY
ON
LY B
E U
SED
FO
R P
URPO
SES
OF
ENG
INEE
RIN
G EV
ALU
ATI
ON
A
ND
FO
RIN
CO
RPO
RA
TIO
N IN
TO T
ECH
NIC
AL
SPEC
IFIC
ATI
ON
S A
ND
OTH
ER D
OC
UM
ENTS
W
HIC
HSP
ECIF
Y P
RO
CU
REM
ENT
OF
PRO
DU
CTS
FRO
M R
AC
AL
INST
RU
MEN
TS IN
C.
C
1. C
ON
NEC
TOR
P2 T
HRU
P8
TO B
E FO
LDED
SO
TH
AT
PIN
#1
IS A
T O
NE
SID
E O
F
CA
BLE
ON
LY A
S SH
OW
N.
2 B
LAC
K IN
K M
ARK
J2-
- A
T P1
APP
ROX.
W
HER
E SH
OW
N.
3 W
HITE
INK
MA
RK J
1--
PER
TABU
LATIO
N
AT
P2 T
HRO
UGH
P8
APP
ROX.
WH
ERE
SHO
WN
.
CA
BLE
#1
IS S
HO
WN
ON
TO
P.
REVI
SED
PER
EO
NO
.236
28 &
RED
RAW
N
ROBI
NSO
N
J103
CO
NN
ECTO
RC
ABL
E #
1J2
00
P2 T
HRU
P8
(P1)
J104
J203
J100
J101
J102
J201
J202
P1
CA
BLE
#2
CA
BLE
#3
CA
BLE
#4
1
(P2)
(P3)
(P4)
(P5)
(P6)
(P7)
(P8)
J105
J106
J107
J108
J109
J110
J111
J112
J113
J114
J115
J116
J117
J118
J119
J120
J121
J122
J123
J124
J125
J126
J127
CO
NN
ECTO
R M
ARK
ING
TA
BULA
TION
10
P2
P3
P1
P4 P6
P5 P7
P8
2
1
2
4072
81
4 RE
QD
C
1
REF
EREN
CE
ON
LYC
ABL
E N
OT
FOLD
ED A
T P2
TH
RU P
83
4
4
J106
J200
A1,
B1
4 S
PRA
Y PR
OTE
CTIV
E C
OA
TING
(ITE
M 3
)
AFT
ER M
ARK
ING
. 5.
MA
TING
REC
EIVE
R BL
OC
K FO
R C
ON
NEC
TORS
P2
TH
RU P
8 IS
TTI
P/N
VG
RCB-
170.
RE
CEI
VER
BLO
CK
MA
TES
WITH
ITA
BLO
CK
P/
N V
GFC
B-17
0. 6.
EN
CLO
SE C
ABL
ES IN
SIN
GLE
BA
G A
ND
ID
ENTIF
Y W
ITH P
ART
NUM
BER
AN
D
CUR
REN
T RE
VISI
ON
.
User Manual 1260-35
Optional Harness Assemblies 6-13
User Manual 1260-35
Optional Harness Assemblies 6-14
User Manual 1260-35
Optional Harness Assemblies 6-15
User Manual 1260-35
Optional Harness Assemblies 6-16
User Manual 1260-35
Optional Harness Assemblies 6-17
User Manual 1260-35
Optional Harness Assemblies 6-18
User Manual 1260-35
Optional Harness Assemblies 6-19
User Manual 1260-35
Optional Harness Assemblies 6-20
User Manual 1260-35
Optional Harness Assemblies 6-21
User Manual 1260-35
Optional Harness Assemblies 6-22
User Manual 1260-35
Product Support 7-1
Chapter 7
PRODUCT SUPPORT
Product Support Racal Instruments has a complete Service and Parts Department.If you need technical assistance or should it be necessary to returnyour product for repair or calibration, call 1-800-722-3262. If partsare required to repair the product at your facility, call 1-949-859-8999 and ask for the Parts Department.
When sending your instrument in for repair, complete the form inthe back of this manual.
For worldwide support and the office closes to your facility, refer tothe Support Offices section on the following page.
ReshipmentInstructions
Use the original packing material when returning the 1260-35 toRacal Instruments for calibration or servicing. The original shippingcrate and associated packaging material will provide thenecessary protection for safe reshipment.
If the original packing material is unavailable, contact RacalInstruments Customer Service for information.
User Manual 1260-35
Product Support 7-2
Support OfficesRacal Instruments, Inc.4 Goodyear St., Irvine, CA 92618-2002Tel: (800) 722-3262, FAX: (949) 859-7309
Racal Instruments, Ltd.480 Bath Road, Slough, Berkshire, SL1 6BE, United KingdomTel: +44 (0) 8706 080134; FAX: +44 (0) 1753 791290
Racal Systems Electronique S.A.18 Avenue Dutartre, 78150 LeChesnay, FranceTel: +33 (1) 3923 2222; FAX: +33 (1) 3923 2225
Racal Systems Elettronica s.r.l.Strada 2-Palazzo C4, 20090 Milanofiori Assago, Milan, ItalyTel: +39 (02) 5750 1796; FAX +39 (02) 5750 1828
Racal Elektronik System GmbH.Frankenforster Strasse 21, 51427 Bergisch Gladbach, GermanyTel:+49 2204 92220; FAX: +49 2204 21491
Racal Australia Pty. Ltd.3 Powells Road, Brookvale, NSW 2100, AustraliaTel: +61 (2) 9936 7000, FAX: +61 (2) 9936 7036
Racal Electronics Pte. Ltd.26 Ayer Rajah Crescent, 04-06/07 Ayer Rajah Industrial Estate, Singapore 0513.Tel: +65 7792200, FAX: +65 7785400
Racal Instruments, Ltd.Unit 5, 25F., Mega Trade Center, No 1, Mei Wan Road, Tsuen Wan, Hong Kong, PRCTel: +852 2405 5500, FAX: +852 2416 4335