1257 1267 1357 1367 zero bacteria food grade valves

1257SERIESZero Bacteria Food Grade Ball & Butterfly Valve

With Pneumatic & Electric Actuator1267SERIES1357SERIES1367SERIES

Yes. We ARE...| ourteously | ttentively | espectably | ffectively | C A R E

SUDER

An ISO 9001:2008 Certified Company

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

2 Way / 3 Way Electric / Pneumatic Actuated Ball Valves

Zero bacteria means a product which has to be free from impurities

and their Key component areas along with important points which is to

be covered in Ball valve and Butterfly valve are as follows:

1. Materials

a) Body Materials

b) Seat Materials

c) Welded component Materials

d) Stem seals

e) End connections

2. Surface Condition

a) Mechanical polishing

b) Electro-polishing

c) Surface finish

3. Drain ability

a) Valve design for minimum hold-up volume

b) Installation Angles

4. Material Composition

a) 316L

b) Sulfur content

c) Certification

5. Inspection

6. Clean ability

7. Marking Information

Seating material should meet the FDA guidelines

Introduction - Zero BacteriaIndexIntroduction………………………………….

Materials & Material composition .......

Applications…………………………….……

Common terms and their definitions

used for Zero Bacteria Valves…...........

Comparison of Zero Bacteria and

Diaphragm Valves …………………….…..

Ball Valves …………………………………..

Technical Specifications of

Ball Valves …….....................................

Exploded view of Ball Valve ……….……

Butterfly Valves …………………….………

Technical Specification of

Butterfly Valves .....................................

Exploded view of butterfly valve ………

Electric Actuator ……………………….……

Control Panel Specification ……….….…

Pneumatic Actuator …………………….…

GA Drawings ……………………….………

Exploded view of Pneumatic Actuator …

SUDE01 1257/1267/1357/1367SERIES

01

02

02

05

07

07

08

08

09

09

10

10

11

12

13

14

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

Materials & Material Composition

The standard material used for zero bacteria valve

is SS316L and its composition is as stated below

(Refer table no 1)

The following are the list of tubing's and fittings to be

used against each size valve (Refer table no.2)

Carbon, MAX

Chromium

Manganese, Max

Molybdenum

Nickel

Phosphorus, MAX

Silicon MAX

Sulfur

0.035

16.00-18.00

2.00

2.00-3.00

10.00-15.00

0.04

0.75

0.005-0.017

CHEMICAL COMPOSITION %

1”

1- ½ ”

2”

2- ½ “

3”

4”

5”

1.000

1.500

2.000

2.500

3.000

4.000

5.000

0.065

0.065

0.065

0.065

0.065

0.0835

0.109

1- ½ ”

1- ½ ”

2”

2-1/2”

3”

4”

5”

Nominal OD Tubing Sizes

Nominal Size In.

Tube OD (in)

Tube Wall Thickness (in)

Hygienic Clamp Size. (in)

Table 1 Table 2

?

?Pharmaceutical

?Food/Beverage

?Cosmetics

?Gas Delivery Systems

?Water Purification

?Brewing/Distilling

?Economical-compared to most other valve

designs

?High flow rate through an unobstructed flow path

?Quick, quarter-turn operation

?Easy to automate pneumatically or electrically

?Inherently flexible to meet a wide range of

pressures and temperatures

?Simple maintainability

?Self-flushing design

?Steam – process temperature control/cleaning

?High purity Water – cleaning

?High purity gas – purging

?CDA (Clean Dry Air) – purging

Bio-Pharm

Applications

?

(cosmetics) / cleaning

?Clean Steam

?WFI-Water for Injection

?Ultra filtration

?CDA-Clean Dry Air

High Purity Water

Alcohol

Alcohol – deliver alcohol to final product

?

?

SUDE 021257/1267/1357/1367SERIES

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

Surface Condition

Under surface condition we should know what is polishing

and how they are important for zero bacteria valves.

Mechanical polishing-Mill finishes welds and surfaces that

have been in service have differing surface characteristics

when viewed under magnification. Mechanical polishing

reduces all surface ridges, pits and discrepancies to

uniform roughness.

Mechanical polishing is accomplished utilizing aluminum

oxide abrasives on rotary equipment. Mechanical

polishing can be achieved by hand held tools for large

surface areas, such as reactors and vessels in place, or

by automatic reciprocating machines for pipe or tubular

components. A series of grit polishes is applied in a

successively finer sequence until the desired finish or

surface roughness is achieved.

Electro polishing is the electrochemical removal of

microscopic irregularities from metal surfaces. It results in

a general leveling or smoothing of the surface, that when

viewed under magnification, appears virtually featureless.

As a result of electro polishing, a metal surface exhibits

the following properties :

1) Surface roughness is significantly reduced, thus

reducing adhesion properties

2) Surface area is reduced as much as 7:1

3) Surface friction and drag are reduced

4) Corrosion resistance is increased due to a

chromium enrichment of the surface and the

removal of surface contaminants that may promote

corrosion

Stain less steel has a natural resistance to corrosion

due to its high chromium content (stainless steels are

typically 16% chromium or higher). Electro polishing

enhances this natural resistance because the process

dissolves more iron (Fe) than chromium (Cr). This

leaves higher levels of chromium on the stainless steel

surface.

The result of any polishing procedure is to create a

“smooth” surface defined as the Roughness Average

(Ra) in micro inch (m-in) or micro-meter (mm).

Surface smoothness is generally measured with a

profilometer an automatic instrument with a stylus-type

reciprocating arm. The stylus is traversed across a

metal surface, measuring peak height and valley depth.

The average peak height and valley depth is then

expressed as a roughness average in term of millionths

of an inch or micro inch, frequently referred to as Ra.

The relationship between polished and buffed mill

finishes, abrasive grit numbers and surface roughness-

before and after electro polishing is illustrated in the

following table (Refer table 3)

120

180

240

320

1.14 max

0.64 max

0.20 to 0.51

0.15 to 0.38

45 max

25 - 30

8 - 20

6 - 15

0.88 -1.12

0.50 - 0.75

0.25 - 0.50

0.20 - 0.38

Girt No

Micro Meters

Micro Inches

Micro Meters

Micro Inches

Before Electro polishing Surface

Roughness, Ra

After Electro polishing Surface Roughness, Ra

35 - 45

20 - 30

10 - 20

8 - 15

Table 3

SUDE03 1257/1267/1357/1367SERIES

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

Drainability

Drain ability is important for maintaining bioprocess

systems in a clean and sterile condition. Fluid

remaining after draining becomes a colonization site

for bacterial or other microorganisms creating an

unacceptable bio burden to the system. A corner

where fluid accumulates also may become a

corrosion-init iat ion corner adding addit ional

contaminants to the system and the design of the

valve it should be in such a way that this accumulation

of product has to be minimized or to be removed.

Clean Ability

The following points are taken care while cleaning

the Zero bacteria valves:

1 Cleaning is performed in a room segregated from the

normal valve production area to eliminate

contamination

2 The room is outfitted with one alkaline cleaning tank

a DI rinse tank and a hot air drying tank

3 Work areas are freshly covered with particles-free

plastic sheeting before each cleaning.

4 Bubble-tight valve testing equipment utilizes clean,

dry, oil-free air.

5 Capping and bagging is performed on the particle-

free surface. All bags are 4 mil and are heat – sealed

Double bag option is available

6 The basic cleaning is performed using an ultrasonic

cleaning system with an approved alkaline agent for

cold cleaning and de-greasing in a residue free

formulation.

7 Each valve component is thoroughly washed in the

cleaning agent tank then rinsed in a de-ionized water

tank. The components are then dried in a hot air

drying vessel.

8 Valve assembly is performed on particle-free surface

using latex gloves. Clean grease-free tools are used

in the assembly of valves.

9 After assembly the valves are nitrogen purged with

99.999% pure N2 filters.

10 The fully assembled valve is tested for leakage using

clean, dry, oil-free air according to industry

standards.

11 Each valve is capped, bagged and heat-sealed to

ensure product quality and purity until installed.

Inspection & Marking

All valves are inspected thoroughly to the required

parameters particularly on the Body surface finish and

marking is done with the help of following information's:

a) Heat number on each component part of the fitting if

more than one heat is used

b) Material type

c) Specification number referencing the BPE standard

d) Internal surface symbol for the appropriate BPE

specification

e) Color coded handles if applicable

All Zero bacteria valves when subjected to steam

sterilization the valve should be designed to withstand a otemperature of 150 C for duration of 100 hours under

continuous duty mode, of course elastomer has to be

chosen properly otherwise the life of the same will be

reduced drastically.

SUDE 041257/1267/1357/1367SERIES

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

Common Terms & Their Definitions Used For Zero Bacteria Valves

SUDE05 1257/1267/1357/1367SERIES

Annealing :

Aseptic :

Aseptic processing :

Automatic welding :

Bio processing:

Bio processing equipment :

Cavitations:

Certification:

Clean:

Clean-in-place (CIP):

A treatment process for the purpose of reducing

hardness, improving mach inability, facilitating cold

working, or producing a desired mechanical physical, or

other property.

Fee of pathogenic (causing or capable of causing

disease) microorganisms.

Operating in a manner that prevents contamination of

the process.

Welding with equipment that performs the welding

operation without adjustment of the controls by a

welding operator. The equipment may or may not

perform the loading and unloading of the work.

The creation of a product utilizing living organisms.

Equipment, systems, or facilities used in the creation of

products utilizing living organisms.

A condition of liquid flow where, after vaporization of the

liquid, the subsequent collapse or vapor bubbles can

produce surface damage.

Documented testimony by qualified authorities that a

system qualification, calibration, validation, or

revalidation has been performed appropriately and that

the results are acceptable.

Free of dirt, residues, detergents, or any contaminants

that may affect or adulterate the product or process.

Internally cleaning a piece of equipment without

relocation or disassembly. The equipment is cleaned

but not necessarily sterilized. The cleaning is normally

done by acid, caustic, or a combination of both, with

Water-for-injection (WFI) rinse.

Clean steam:

Cloudiness:

Dead leg:

Demarcation:

Fermentation:

Ferment:

Full penetration:

Heat number:

Hold-up-volume:

Hydro test:

Steam free from boiler additives that may be purified,

filtered, or separated. Usually used for incidental

heating in pharmaceutical applications.

The appearance of a milky white hue across some

portion of a surface resulting from the electro polish

process.

An area of entrapment in a vessel or piping run that

could lead to contamination of the product.

A localized area that is dissimilar to the surrounding

areas with a defined boundary after electro polishing.

The biochemical synthesis of organic compounds by

microorganisms or cultivated cells.

A vessel for carrying out fermentation.

A weld joint is said to be fully penetrated when the

depth of the weld extends from its face into the weld

joint so that the joint is fully fused. For a tube-to-tube

weld, no unused portions of the weld joint shall be

visible on the inside diameter of fully penetrated weld.

An alphanumeric identification of a stated tonnage of

metal obtained from a continuous melting in a furnace.

The volume of liquid remaining in a vessel or piping

system after it has been allowed to drain.

A pressure test of piping, pressure vessels, or

pressure-containing parts, usually performed by

pressurizing the internal volume with water at a

pressure determined by the applicable code.

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

SUDE 061257/1267/1357/1367SERIES

Hygienic :

Hygienic clamp joint:

Machine welding:

Micron or micrometer (mm):

Orange peel:

Passivation:

Passive layer:

Pipe:

Porosity:

Of or pertaining to equipment and piping systems that

by design, materials of construction, and operation

provided for the maintenance of cleanliness so that

products produced by these systems will not adversely

affect human or animal health.

A tube outside diameter union consisting of two

neutered ferrules having flat faces with a concentric

groove and mating gasket that is secured with a

clamp, providing a non protruding, recess less product

contact surface.

Welding with equipment that performs the welding

operation under the constant observation and control

of a welding operator. The equipment may or may not

perform the loading and unloading of the works.

One-millionth of a meter.

An appearance of a pebbly surface.

A final treatment/cleaning process used to remove free

iron or other anodic contaminants from the surface of

corrosion-resistant steel parts such that uniform

formation of a passive layer is obtained.

A passive oxidized film that forms naturally on the

stainless steel surface when exposed to air or similar

oxidizing environment protecting the underlying base

metal from corrosion.

Pipe size is determined by diameter and schedule.

For bioprocess equipment, pipe does not include tube

Cavity-type discontinuities formed by gas entrapment

during solidification.

Pure steam:

Pyrogen:

Ra:

Self-draining:

Square cut:

Steam in place (SIP):

Sterile:

Surface Inclusion:

Surface residual:

Tube:

Steam that is produced by a steam generator which,

when condensed, meets requirements for Water-for-

injection (WFI).

A fever-producing substance.

Log of the arithmetic mean of the surface profile.

Usually expressed in min as related to roughness.

The elimination of all fluid from the system due to the

force of gravity alone.

A tube end cut perpendicular to the tangent plane.

The use of steam to sanitize or sterilize a piece of

equipment without the use an autoclave.

Free living organisms.

Particles of foreign material in a metallic matrix. The

particles are usually compounds such as oxides,

sulfides, or silicates, but may be a substance foreign

to and essentially insoluble in the matrix.

A foreign substance that adheres to a surface by

chemical reaction, adhesion, adsorption, or ionic

bonding (for example, corrosion, rouging, and

staining).

Tube is sized by its nominal outside diameter. For bio-

processing equipment, tube does not include pipe.

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

Comparision Of Zero Bacteria And Diaphragm Valves

Zero Bacteria valves are widely used in process applications because of their inherent versatility. Diaphragm valves

offer a limited service range for temperature and pressure and do not meet all of the standards for industrial valves.

Zero Bacteria valves are available for:

Cryogenic service High temperature / Low temperature

High velocity / Low velocity High pressure / Low pressure

Wider range of seat materials wider range of body materials

Wider range of end connections Fire-safe designs

In addition, zero bacteria valve center sections are removable to allow access to the inner weld bead where

cleaning and/or polishing may then be performed.

Ball Valve

A Precision ball with a full port is positioned inside the

valve body between two flanges and two PTFE valve

seats. The 90° rotation of the valve stem, through the

handle or a pneumatic / Electrical actuator, is

transferred, to the ball thereby opening or closing the

valve.

The valve consists of a valve body, two flanges, PTFE

valve seats, EPDM O-ring, ball, stem and a handle or

actuator. All Seats and seals are made from FDA

approved material.

The Valve body, flanges and ball are made of forged

316L stainless steel which ensures non porous,

smooth and dimensionally stable construction.

The valve is designed to maintain a full rate, with a

minimum pressure drop and it is fully drainable.

A Bottom entry, precision machined stem with a live

loaded PTFE thrust washer ensures a Smooth rotation

at various temperatures and pressure Conditions.

Purge ports are provided on the valve body for SIP /

CIP applications

Standard Design:

Available Sizes:

Available Types:

End connections:

Materials:

Actuator option:

1”, 1 ½”, 2”, 2 ½”, 3”, 4”

Butt weld

Sanitary Clamp

I-Line

Sanitary Clamp, Butt-Weld, Extended Butt Weld (for

high purity applications), I-Line or others on request.

AISI 316L or AISI 304L

0Electrical/Pneumatic 90 Open/ Close

SUDE07 1257/1267/1357/1367SERIES

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

Technical Specifications of Ball Valve

Material :

Product wetted steel parts AISI 316L/AISI 304L

Other steel parts …… AISI 304

FDA Seals :

Valve Seat …… TFM / PTFE

O-ring …… EPDM

Cavity filler (optional) …… TFM /PTFE

Nominal Pressure :

Maximum product pressure …… 200 PSI maximum (14 Bars)

Test pressure 235 PSI (16 Bars)

Temperature Range : …… 60' Degrees Fahrenheit to +300' Degrees Fahrenheit

*Other seal material available for higher temperatures

Surface Finish:

Contact with product …… Ra</=25µ in (Girt 220g)

Optional …… Ra</=15µ in (Girt 320g)

Connections : …… Sanitary Clamp (ISO 2852/BS 4825-3)

Optional : …… Butt Weld (ISO 2037/BS 4825-01)

I-Line, Other connections on request

Purge Port Connections : …… 1/4” Males BSP (Refer figure no.1)

……

Exploded View of Standard Ball Valve

12345678

BODYO-RINGO-RINGFLANGECAP SCREWBALLSEATBUSHING

AISI 316L/AISI 304LEPDMEPDMAISI 316L/AISI 304LAISI 304AISI 316L/AISI 304LTFM PTFEPTFE

Sl. No. Description Material

9101112131415

STEMTHRUST RINGO-RINGINDEX BASETHRUST WASHERDRAIN CAPWASHER

AISI 316L/AISI 304LPTFEEPDMAISI 304PTFEAISI 316L/AISI 304LPTFE


SUDE 081257/1267/1357/1367SERIES

13

12

11

10

9

8

7

2

6

1

14

15

3

4

5

Fig. 1

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

Available Types:

Options:

End Connections :

Material:

?Butt-Weld

?Sanitary Clamp

?I-Line

?Variety of multiple position handles for manual

operation.

?Automatic operation by vertical pneumatic / electrical

actuators

Sanitary Clamp, Butt-Weld, I-Line, or others on

request.

AISI 316L or AISI 304L

Butterfly Valve

Working Principle:

Standard Design:

Available Sizes:

Quarter turn (90º rotation) operation closes or opens

the valve. A wide variety of actuators allow the valve

disc to be set at various positions so that the flow rate

can be regulated.

The valve consists of two valve bodies and a disc made

from forged stainless steel which ensures a non porous,

smooth surface and dimensionally stable construction.

The valve disc has a dense and polished surface which

combined with a slim design allows for a high Cv. The

PTFE stem bushing ensures an extra smooth disc

rotation. All seats and seals are made from FDA

approved materials. The valves are assembled by

means of Allen head cap screws.

1”, 1 ½”, 2”, 2 ½”, 3”, 4”, 5”, 6”, 8”

Technical Specification of Ball Valve

Material :

Product wetted steel parts …… AISI 316L or AISI 304L

Other steel parts …… AISI 304

FDA Seals :

Standard …… SILICONE

Optional …… VITON, EPDM, BUNA, PTFE

Nominal Pressure:

Maximum Product Pressure …… 147 PSI maximum (10 Bars)

Test pressure 176 PSI (12 Bars)

Surface Finish:

Surface in contact with product …… Ra </= 25 µ in (Grit 220g)

Optional …… Ra </= 25 µ in (Grit 320g)

Connections …… Sanitary Clamp (ISO 2852 / BS 4825)

Optional …… Butt Weld (ISO 2037 / BS 4825), I-Line

(Refer figure No. 2)

SUDE09 1257/1267/1357/1367SERIES

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

1

2

3

4

5

DISC

BUSHING

FLANGE

SEAT

SCREW

AISI 316L/AISI 304L

PTFE

AISI 316L/AISI 304L

SILICONE

AISI 304


Easier interface with digital control devices. Electrical actuators must have a voltage selection, typical actuators

voltages are 24V AC, 110V AC, 240 V AC and 415 Volts. Fail safe electric actuators are also called spring return and

the fail positioning (open or closed) should be noted. For detail on the Electric actuator refer Sdtork pune and asked for

detailed literature. The spring return Electrical actuators are available for low torque, for higher values we suggest you

to use reversible stay put type actuator

Exploded View of Standard Butterfly Valve

Actuator Construction

Single Phase

Single phase SDTORK Actuator is provided with Stall duty motor used

for quarter turn application. Actuator is suitable for inching operation

too and they can be supplied with extra limit switches for remote

position indication.

The Actuator are available in general purpose, Dust proof & Flame

proof & Explosion proof housing approved by CMRS Dhanbad.

Three phases SDTORK Actuator is basically a worm gear type

reduction gear box. A single stage grease bath worm gear gives

quietness and reliability in operation. The valve can be fully opened,

fully closed or adjusted to any intermediate position. The rectory force

on the worm shaft which is a 'Floating one' is directly proportional to

the out put torque and is absorbed by a set of disc springs. The lateral

movement of the worm shaft under load, trips closes the Torque

switch.

SUDE 101257/1267/1357/1367SERIES

Electrical Actuator

2

1

5

324

Fig. 2

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

Three Phase

Three phase Actuator are fitted with torque limit switches & travel limit

switches & also they are in built with manual hand wheel used for operating

the actuator manually in case of power failure. Actuator is also supplied with

various shaft designs to suit rising & non rising stem valve. Three phases

are also provided with space heater. This actuator is also available in slow

mode operation which is used for multi turn application.

The driving motor is a TEFC squirrel cage class F IP 65 enclosure motor

combining low inertia with a high starting and stalling torque.

Common Accessory for Single Phase / Three Phase Actuator :

a) Honeywell / any other make PID Controller along with PT 100 sensor with

built in panel as an option.

b) Honeywell / any other make pressure Transmitter where based on setting

pressure valve will open & close through PID with built in panel as a option.

c) Sequential timer 0 to 30 channel for sequence operation.

d) Cyclic timer having On time - 1 to 60 seconds & Off time - 1 to 60 min for

sequencing operation.

e) Stimulator –panel mounting type having two knobs used for generating

4 to 20mA with the help of 230 Volt A.C. Supply.

a) Travel Limit Switches - 2 nos

b) Auxiliary Limit Switches - 2 nos

c) Hand wheel for Manual operation

d) Local position indicator

e) Potentiometer for feed back

f) Torque limit switches

g) Position Transmitter

The Actuators can be supplied with

a panel having Auto Calibration facility.

Actuator can also be supplied with :

Single Phase OR Three phase Panel for switching the valve On / Off through Push

Buttons for local operation under manual mode OR through PLC under Auto mode

through 4-20 mA, 0 to 10 V DC.

Accessories For Actuator

Control Panel Specification

a) Input : Single Phase 230 V AC OR 3 Phase 415 V AC, 4 wire supply.

b) Output supply: Single Phase 230 V AC OR 3 phase 415 V AC

Reversible supply.

c) Auto / Manual selection : Selector switch provided. In Auto mode open &

close operation is controlled by 4-20mA Input & under Manual mode

operation is through Push buttons.

d) Indications : Zero to a100% valve position display, R, Y, B Phase

Indication [applicable only for 3 phase] Open & Close, Fully open & Fully

close indication.

e) Main switch - Single Phase OR 3 Phase MCB for mains On / Off.

f) Phase fail / error protection provided.

g) Fuse protection provided for each phase.

h) Protection from over torque - If Actuator gets over torque the torque

switch trips & the system protects the motor. Also provided with 10

meters cable for Motor & Feed back with connectors. (Fig. 3)

SUDE11 1257/1267/1357/1367SERIES

Wall Mounted Constructionin sheet metal

Integral Construction

Fig. 3

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

Pneumatic actuators are available in rotary construction in Double

and spring return in on/off and modulating duty format. Actuators

will be inherently fail safe but fail position (open or closed) should

be noted. Pneumatic actuators are supplied with Electro pneumatic

petitioners which work on continuous pressurized air of 60psi and

input signal of 4 to 20mA with feed back 4to20ma For details refer

Actuator catalogue.

Pneumatic Actuator

Actuator Construction

Air Pressure Requirement :2a) For Double Acting Actuator - 3.5 kg / cm

2 (Minimum) & 8.5kg / cm (Maximum)2b) For Spring Return Actuator - 4.0 kg / cm

2 (Minimum) & 8.5 kg / cm (Maximum)

However Air Pressure Requirement is much

dependent on size of the valve, working pressure,

quality of Butterfly valve and many other factors.

For Double Acting Actuator:

4 way 5 port single Coil / Double Coil solenoid valve in

general purpose or Flame proof and explosion coils

construction.

For Spring Return Actuator:

3 way Single Coil / Double Coil solenoid valve in

General purpose or Flame proof and explosion Coils

construction.

The piston incorporates racks and end covers are die

casted in aluminum alloy. Barrel is extruded.

aluminium alloy hardened and treated, further finished

with deep anodized process to form a protective layer

to resist atmospheric corrosion. The actuators are also

available in stainless steel 316 & Nylon plastic

construction for food grade and chemical industries

application. The internal materials of the actuator are

having pinion which is made up of steel, precision cut,

heat treated and ground & also has a high trade of

synthetic seals. The actuators before assembly is

lubricated with high temperature resistant smooth

grease. The actuators are with compact design

operates through 90 degree angle of actuation. The

Actuator is also available in 180 degree rotation. Refer

Fig. 4

Accessories

Accessory Common for Double Acting /

Spring Return Actuator :

a) Pressure Regulator

b) Limit Switches

c) Filter Regulator with Lubricator

d) Gear Box with hand wheel for manual operation

e) Valve Positioner for characteristic controlled

application.

f) I to P Converter.

g) Electro pneumatic positioners

h) Position Indicator

i) Position Transmitter

j) Cyclic Timer OR Sequential Timer

k) 3 Way / 4 Way Key operated valves

l) Stimulator

m) Travel Stops

n) Flow Restricter

o) Silencers with Flow Control Valve

Optional :

a) PID Controller along with PT - 100 Senso

supplied with panel.

b) Pressure Transmitter supplied with panel.

SUDE 121257/1267/1357/1367SERIES

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

Exploded View of Pneumatic Actuator

Tests

The valves are tested according to their respective standards for hydrostatic, seat leakage and working pressure tests.

Unless and otherwise specified Ball valves are Constructed and tested for10 kg/cm2 working pressure.

Notes :

2a) Actuator rating is for valve working pressure 10 kg / cm

b) Timing given is approximate and is useful as an indicating figure only when solenoid valve is directly coupled with

the Actuator. Average time under 50% load condition is 80 PSI working pressure.

c) All data is complied in laboratory test, in actual field, working may differ.

d) Width and weight will change with rating of flanges and accessories.

Allen ScrewDouble Acting Cap Cap O-ringPistonCylinderWasherSpring ClipPosition IndicatorPiston GuideGuide RingPiston O-RingO-RingO-RingSprings SetSpring Return CapShaftGearWatertightness Plane Gasket

123456789101112131415161718

1222211114242212112

AISI -304 Stainless SteelAluminium Alloy (2) + (1)N.B.R.Aluminium AlloyAluminium Alloy (2) + (1)Polyamide 6Steel (3)PolymideP.T.F.E. + BronzeP.T.F.E. + BronzeN.B.R.N.B.R.N.B.R.DIN - 17223-C (2) (4)Aluminium Alloy (2) + (1)Steel (2)Aluminium Alloy (5) N.B.R.

DescriptionNo. Quantity Material

SUDE13 1257/1267/1357/1367SERIES

1

2

3

4

5

7

6

8

9

10

14

11

12

15

14

13

Fig. 4

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

1367Butt-Weld Metalic Ball Valve with

Pneumatic Rotary Single/Double Acting Actuator

I

5 6

7

42 3

1

9

8

11

10

12

H

GD

EF

K

L

C

J

B

A

BILL OF MATERIAL OF VALVE WITH ACTUATOR

S.No. PART MATERIALSINDICADOR VISUAL POSITION INDICATORPISTON GUIDEGUIDE RINGPISTON O-RINGTAPA DOBLEEFECTO DOUBLE ACTING CAPSPRING SETSPRING RETURN CAPBODYFLANGECAP SCREWO-RINGSEAT

--POLYACETALPOLYACETALNITRILE--DIN-17223-CALLUMININUM ALLOYAISI316LAISI316LAISI 304EPDMTFM PTFE

123456789101112

VALVE SIZE MODEL NUMBER

1367/25/BW/AISI316L/AISI316L/DAW

1367/25/BW/AISI316L/AISI316L/SAW

1367/40/BW/AISI316L/AISI316L/DA00

1367/40/BW/AISI316L/AISI316L/SA00









25

40

50

65

80

100

APPROX.TIME

AIR CONSUMP-TION IN LTR WT. OF

ASSYIN KGS.

2.15

2.3

2.9

3.15

4.1

4.9

6.47

7.18

10.37

12.45

17.1

20.26

CvValue

66

66

192

192

434

434

723

723

1124

1124

2100

2100

FOROPEN

0.2

0.3

0.3

0.3

0.4

0.4

0.5

0.5

0.5

0.6

0.8

1.0

FORCLOSE

0.2

0.3

0.3

0.3

0.4

0.4

0.5

0.5

0.5

0.6

0.8

1.0

FOR OPEN

0.075

0.075

0.15

0.15

0.28

0.28

0.33

0.33

0.33

0.33

0.8

0.8

FORCLOSE

0.05

0.1

0.25

0.32

0.32

0.7

A

94.05

94.05

107.15

107.15

117.07

117.07

135.73

135.73

157.95

157.95

170.25

170.25

B

34.13

34.13

41.27

41.27

49.21

49.21

59.53

59.53

65.88

65.88

86.91

86.91

C

22.22

22.22

34.92

34.92

47.62

47.62

60.32

60.32

72.62

72.62

97.63

97.63

D

8

8

10

10

10

10

10

10

10

10

10

10

E

7.5

7.5

11

11

11

11

11

11

11

11

11

11

F

20

20

30

30

30

30

30

30

30

30

30

30

I

85

85

110

110

122

122

127

127

127

127

148

148

J

72.23

72.23

81.35

81.35

98.42

98.42

107.15

107.15

114.3

114.3

127.00

127.00

K

157.23

157.23

191.35

191.35

220.42

220.42

234.15

234.15

241.3

241.3

275.00

275.00

L

191.36

191.36

232.62

232.62

269.63

269.63

293.68

293.68

307.18

307.18

361.91

361.91

DIMENSIONS (MM)

G

109

125

146

182

182

203

H

143.5

160.00

194.00

236.00

236.00

266.00

SUDE 141257/1267/1357/1367SERIES

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

1367

K

I

5 6

7

42 3

1

9

8

11

10

12

H

GD

EF

L

C

J

B

A

Sanitary Clamp Metalic Ball Valve with





123456789101112


1367/25/SC/AISI316L/AISI316L/DAW

1367/25/SC/AISI316L/AISI316L/SAW

1367/40/SC/AISI316L/AISI316L/DAOO

1367/40/SC/AISI316L/AISI316L/SA00

1367/50/SC/AISI316L/AISI316L/DA05








25

40

50

65

80

100

FOROPEN

FORCLOSE

APPROX.TIME

FOROPEN

FORCLOSE


ASSYIN KGS.

2.65

2.8

3.4

3.65

4.6

5.4

6.97

7.68

10.87

12.95

17.6

20.76

Cv

66

66

192

192

434

434

723

723

1124

1124

2100

2100

0.2

0.3

0.3

0.3

0.4

0.4

0.5

0.5

0.5

0.6

0.8

1.0

0.2

0.3

0.3

0.3

0.4

0.4

0.5

0.5

0.5

0.6

0.8

1.0

0.075

0.075

0.15

0.15

0.28

0.28

0.33

0.33

0.33

0.33

0.8

0.8

0.05

0.1

0.25

0.32

0.32

0.7

A

94.05

94.05

107.15

107.15

117.07

117.07

135.73

135.73

157.95

157.95

170.25

170.25

B

34.13

34.13

41.27

41.27

49.21

49.21

59.53

59.53

65.88

65.88

86.91

86.91

C

22.22

22.22

34.92

34.92

47.62

47.62

60.32

60.32

72.62

72.62

97.63

97.63

D

8

8

10

10

10

10

10

10

10

10

10

10

E

7.5

7.5

11

11

11

11

11

11

11

11

11

11

F

20

20

30

30

30

30

30

30

30

30

30

30

G

109

125

146

182

182

203

H

143.5

160.00

194.00

236.00

236.00

266.00

I

85

85

110

110

122

122

127

127

127

127

148

148

J

72.23

72.23

81.35

81.35

98.42

98.42

107.15

107.15

114.3

114.3

127.00

127.00

K

157.23

157.23

191.35

191.35

220.42

220.42

234.15

234.15

241.3

241.3

275.00

275.00

L

191.36

191.36

232.62

232.62

269.63

269.63

293.68

293.68

307.18

307.18

361.91

361.91

DIMENSIONS (MM)

SUDE15 1257/1267/1357/1367SERIES

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

1367

K

I

5 6

7

42 3

1

9

8

11

10

12

H

GD

EF

L

C

J

B

A




123456789101112

I-Line Metalic Ball Valve with



1367/25/IL/AISI316L/AISI316L/DAW

1367/25/IL/AISI316L/AISI316L/SAW

1367/40/IL/AISI316L/AISI316L/DAOO

1367/40/IL/AISI316L/AISI316L/SA00

1367/50/IL/AISI316L/AISI316L/DA05








25

40

50

65

80

100

FOROPEN

FORCLOSE

APPROX.TIME

FOROPEN

FORCLOSE


ASSYIN KGS.

3.09

3.24

3.88

4.13

5.22

6.02

8.02

8.73

12.67

14.75

20.6

23.76

Cv

66

66

192

192

434

434

723

723

1124

1124

2100

2100

0.2

0.3

0.3

0.3

0.4

0.4

0.5

0.5

0.5

0.6

0.8

1.0

0.2

0.3

0.3

0.3

0.4

0.4

0.5

0.5

0.5

0.6

0.8

1.0

0.075

0.075

0.15

0.15

0.28

0.28

0.33

0.33

0.33

0.33

0.8

0.8

0.05

0.1

0.25

0.32

0.32

0.7

101.99

101.99

109.93

109.93

140.49

140.49

142.08

142.08

170.65

170.65

202.00

202.00

34.13

34.13

41.27

41.27

49.21

49.21

59.53

59.53

65.88

65.88

86.91

86.91

22.22

22.22

34.92

34.92

47.62

47.62

60.32

60.32

72.62

72.62

97.63

97.63

8

8

10

10

10

10

10

10

10

10

10

10

7.5

7.5

11

11

11

11

11

11

11

11

11

11

20

20

30

30

30

30

30

30

30

30

30

30

109

125

146

182

182

203

143.5

160.00

194.00

236.00

236.00

266.00

85

85

110

110

122

122

127

127

127

127

148

148

72.23

72.23

81.35

81.35

98.42

98.42

107.15

107.15

114.3

114.3

127.00

127.00

157.23

157.23

191.35

191.35

220.42

220.42

234.15

234.15

241.3

241.3

275.00

275.00

A B C D E F G H I J K L

191.36

191.36

232.62

232.62

269.63

269.63

293.68

293.68

307.18

307.18

361.91

361.91

DIMENSIONS (MM)

SUDE 161257/1267/1357/1367SERIES

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

1267

K

9

8

10

2 3

1

75 6

4

H

GD

EF

M

B

C

A

L

D

J

8


S.No. PART MATERIALSTAPA DOUBLE EFECTO DOUBLE ACTING CAPSPRING SETSPRING RETURN CAPVISUAL POSITION INDICATORPISTON GUIDEGUIDE RINGPISTON O-RINGFLANGESCREWSEAT

--DIN-17223-CALLUMINIUM ALLOY--POLYACETALPOLYACETALNITRILEAISI 316LAISI 304SILICON

12345678910

Butt-Weld Metalic Butterfly Valve with



1267/25/BW/AISI316L/AISI316L/DAW

1267/25/BW/AISI316L/AISI316L/SAW

1267/25/BW/AISI31 6L/AISI31 6L/DAW

1267/25/BW/AISI31 6L/AISI31 6L/SAW

1267/25/BW/AISI31 6L/AISI31 6L/DA00

1267/25/BW/AISI31 6L/AISI31 6L/SA00













Cv

22

22

80

80

195

195

250

250

400

400

840

840

1200

1200

1900

1900

3200

3200

A

22.22

22.22

34.92

34.92

47.62

47.62

60.32

60.32

72.61

72.61

97.61

97.61

121.43

121.43

146.83

146.83

200.02

200.02

B

25.4

25.4

38.1

38.1

50.8

50.8

63.5

63.5

76.2

76.2

101.6

101.6

127

127

152.4

152.4

203.2

203.2

C

68.07

68.07

76.2

76.2

80.01

80.01

80.01

80.01

80.01

80.01

88.9

88.9

88.9

88.9

89.07

89.07

89.66

89.66

D

84.82

84.82

87.36

87.36

97.52

97.52

101.85

101.85

107.95

107.95

124.61

124.61

149.86

149.86

165.86

165.86

187.96

187.96

E

143.5

143.5

143.5

143.5

160.00

160.00

160.00

160.00

194.00

194.00

194.00

194.00

236.00

236.00

266.00

266.00

312.00

312.00

F

109.00

109.00

109.00

109.00

125.00

125.00

125.00

125.00

146.00

146.00

146.00

146.00

182.00

182.00

203.00

203.00

234.00

234.00

G

8.00

8.00

8.00

8.00

10.00

10.0

10.00

10.00

10.00

10.00

10.00

10.00

10.00

10.00

10.00

10.00

16.00

16.00

H

7.5

7.5

7.5

7.5

11.00

11.00

11.00

11.00

11.00

11.00

11.00

11.00

11.00

11.00

11.00

11.00

11.00

11.00

I

20.00

20.00

20.00

20.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

J

85.00

85.00

85.00

85.00

110.00

110.00

110.00

110.00

122.00

122.00

122.00

122.00

127.00

127.00

148.00

148.00

161.00

161.00

K

169.82

169.82

172.36

172.36

207.52

207.52

211.85

211.85

229.95

229.95

246.61

246.61

276.86

276.86

313.86

313.86

348.96

348.96

L

79.24

79.24

84.83

84.83

104.64

104.64

111.76

111.76

124.46

124.46

156.97

156.97

180.08

180.08

211.83

211.83

256.28

256.28

M

209.44

209.44

214.77

214.77

259.84

259.84

268.73

268.73

292.18

292.18

325.09

325.09

366.9

366.9

419.77

419.77

477.1

477.1

FORCLOSE

OPPROX.TIME

FOROPEN

FORCLOSE


ASSYIN KGS.FOR

OPEN

1.05

1.2

1.15

1.15

3.1

2.25

3.5

3.7

3

3.8

4.5

5.58

6.57

8.65

7.8

10.96

11.07

16.7

0.2

0.3

0.2

0.3

0.3

0.4

0.3

0.4

0.4

0.4

0.4

0.5

0.5

0.6

0.8

1

1

1.6

0.075

0.075

0.075

0.075

0.15

0.15

0.15

0.15

0.28

0.15

0.28

0.28

0.33

0.33

0.8

0.8

1.5

1.5

0.05

0.05

0.1

0.1

0.25

0.25

0.32

0.7

1.2

0.7

0.2

0.3

0.2

0.3

0.3

0.4

0.3

0.4

0.4

0.4

0.4

0.5

0.5

0.6

0.8

1

1

1.6

DIMENSIONS (MM)

25

40

50

65

80

100

125

150

200

SUDE17 1257/1267/1357/1367SERIES

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

1267

J

9

8

10

2 3

1

75 6

4

D

EF

GH

L

B

A

K

C

I

8




12345678910

Sanitary Clamp Metalic Butterfly Valve with



25

40

50

65

80

100

125

150

200



















Cv

22

22

80

80

195

195

250

250

400

400

840

840

1200

1200

1900

1900

3200

3200

A

22.22

22.22

34.92

34.92

47.62

47.62

60.32

60.32

72.61

72.61

97.61

97.61

121.43

121.43

146.83

146.83

200.02

200.02

B

68.07

68.07

76.2

76.2

80.01

80.01

80.01

80.01

80.01

80.01

88.9

88.9

88.9

88.9

89.07

89.07

89.66

89.66

C

84.82

84.82

87.36

87.36

97.52

97.52

101.85

101.85

107.95

107.95

124.61

124.61

149.86

149.86

165.86

165.86

187.96

187.96

D

143.5

143.5

143.5

143.5

160.00

160.00

160.00

160.00

194.00

194.00

194.00

194.00

236.00

236.00

266.00

266.00

312.00

312.00

E

109

109.00

109.00

109.00

125.00

125.00

125.00

125.00

146.00

146.00

146.00

146.00

182.00

182.00

203.00

203.00

234.00

234.00

.00

F

8

8.00

8.00

8.00

10.00

10.00

10.00

10.00

10.00

10.00

10.00

10.00

10.00

10.00

10.00

10.00

16.00

16.00

.00

G

7.5

7.5

7.5

7.5

11.00

11.00

11.00

11.00

11.00

11.00

11.00

11.00

11.00

11.00

11.00

11.00

11.00

11.00

H

20

20.00

20.00

20.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

.00

I

85

85.00

85.00

85.00

110.00

110.00

110.00

110.00

122.00

122.00

122.00

122.00

127.00

127.00

148.00

148.00

161.00

161.00

.00

J

169.82

169.82

172.36

172.36

207.52

207.52

211.85

211.85

229.95

229.95

246.91

246.91

276.86

276.86

313.86

313.86

348.96

348.96

K

79.24

79.24

84.83

84.83

104.64

104.64

111.76

111.76

124.46

124.46

156.97

156.97

180.08

180.08

211.83

211.83

256.28

256.28

L

209.44

209.44

214.77

214.77

259.84

259.84

268.73

268.73

292.18

292.18

325.09

325.09

366.9

366.9

419.77

419.77

477.1

477.1

CLOSE (SEC.)

OPPROX.TIME

TO OPEN

TO CLOSE


ASSYIN KGS.OPEN

(SEC.)

1.25

1.4

1.3

1.45

3.5

2.65

3.9

4.1

3.5

4.3

5

6.08

7.07

9.15

8.6

11.76

11.77

17.4

0.2

0.3

0.2

0.3

0.3

0.4

0.3

0.4

0.4

0.4

0.4

0.5

0.5

0.6

0.8

1

1

1.6

0.075

0.075

0.075

0.075

0.15

0.15

0.15

0.15

0.28

0.15

0.28

0.28

0.33

0.33

0.8

0.8

1.5

1.5

0.05

0.05

0.1

0.1

0.25

0.25

0.32

0.7

1.2

0.7

0.2

0.3

0.2

0.3

0.3

0.4

0.3

0.4

0.4

0.4

0.4

0.5

0.5

0.6

0.8

1

1

1.6

DIMENSIONS (MM)

SUDE 181257/1267/1357/1367SERIES

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

1267

J

9

8

10

2 3

1

75 6

4

D

EF

GH

L

B

A

K

C

I

8




12345678910

I-Line Metalic Butterfly Valve with



25

40

50

65

80

100

125

150

200



















Cv

22

22

80

80

195

195

250

250

400

400

840

840

1200

1200

1900

1900

3200

3200

A

22.22

22.22

34.92

34.92

47.62

47.62

60.32

60.32

72.61

72.61

97.61

97.61

121.43

121.43

146.83

146.83

200.02

200.02

B

75.00

75.00

75.00

75.00

85.72

85.72

84.12

84.12

92.07

92.07

109.93

109.93

113.48

113.48

113.48

113.48

113.48

113.48

C

84.82

84.82

87.36

87.36

97.52

97.52

101.85

101.85

107.95

107.95

124.61

124.61

149.86

149.86

165.86

165.86

187.96

187.96

D

143.5

143.5

143.5

143.5

160.00

160.00

160.00

160.00

194.00

194.00

194.00

194.00

236.00

236.00

266.00

266.00

312.00

312.00

E

109

109.00

109.00

109.00

125.00

125.00

125.00

125.00

146.00

146.00

146.00

146.00

182.00

182.00

203.00

203.00

234.00

234.00

.00

F

8

8.00

8.00

8.00

10.00

10.00

10.00

10.00

10.00

10.00

10.00

10.00

10.00

10.00

10.00

10.00

16.00

16.00

.00

G

7.5

7.5

7.5

7.5

11.00

11.00

11.00

11.00

11.00

11.00

11.00

11.00

11.00

11.00

11.00

11.00

11.00

11.00

H

20

20.00

20.00

20.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

30.00

.00

I

85

85.00

85.00

85.00

110.00

110.00

110.00

110.00

122.00

122.00

122.00

122.00

127.00

127.00

148.00

148.00

161.00

161.00

.00

J

169.82

169.82

172.36

172.36

207.52

207.52

211.85

211.85

229.95

229.95

246.91

246.91

276.86

276.86

313.86

313.86

348.96

348.96

K

79.24

79.24

84.83

84.83

104.64

104.64

111.76

111.76

124.46

124.46

156.97

156.97

180.08

180.08

211.83

211.83

256.28

256.28

L

209.44

209.44

214.77

214.77

259.84

259.84

268.73

268.73

292.18

292.18

325.09

325.09

366.9

366.9

419.77

419.77

477.1

477.1

CLOSE (SEC.)

OPPROX.TIME

TO OPEN

TO CLOSE


ASSYIN KGS.OPEN

(SEC.)

1.41

1.56

1.47

1.62

3.78

2.93

4.26

4.46

3.9

4.7

5.7

6.78

8.11

10.19

9.8

12.96

13.41

19.04

0.2

0.3

0.2

0.3

0.3

0.4

0.3

0.4

0.4

0.4

0.4

0.5

0.5

0.6

0.8

1

1

1.6

0.075

0.075

0.075

0.075

0.15

0.15

0.15

0.15

0.28

0.15

0.28

0.28

0.33

0.33

0.8

0.8

1.5

1.5

0.05

0.05

0.1

0.1

0.25

0.25

0.32

0.7

1.2

0.7

0.2

0.3

0.2

0.3

0.3

0.4

0.3

0.4

0.4

0.4

0.4

0.5

0.5

0.6

0.8

1

1

1.6

DIMENSIONS (MM)

SUDE19 1257/1267/1357/1367SERIES

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

1357Butt-Weld Metalic Ball Valve with

Single Phase Electrical Actuator

7

6

9

8

10

C

D

B

A

5

4

M

J K

N

L

1

2

3

I

H G

E F


S.No. PART MATERIALSELECTRIC ACTUATOR STAY PUT TYPE MOTORHAND WHEELOUTPUT BORECABLE GLANDSBODYFLANGECAP SCREWO-RINGSEAT

SDTORK MAKE

AISI316LAISI316LAISI 304EPDMTFM PTFE

12345678910


FOROPEN

FORCLOSE

APPROX.TIME WT. OF

ASSYIN KGS.

1357/25/BW/AISI316L/AISI316L/SD-1000-03

1357/40/BW/AISI316L/AISI316L/SD-1000-03

1357/50/BW/AISI316L/AISI316L/SD-1000-05

1357/65/BW/AISI316L/AISI316L/SD-1000-05

1357/80/BW/AISI316L/AISI316L/SD-1000-10

1357/100/BW/AISI316L/AISI316L/SD-1000-10

25

40

50

65

80

100

9.70

9.90

11.60

13.60

20.50

26.50

Cv

66

192

434

723

1124

2100

17.00

17.00

17.00

20.00

20.00

20.00

17.00

17.00

17.00

20.00

20.00

20.00

A

94.05

107.15

117.07

135.73

157.95

170.25

B

34.13

41.27

49.21

59.53

65.88

86.91

C

22.22

34.92

47.62

60.32

72.62

97.63

D

72.23

81.35

98.42

107.15

114.3

127.00

E

68

68

68

95

95

123

F

117

117

117

148

148

182

G

175

175

175

250

250

261

H

247.2

256.3

273.4

357.1

364.3

388.0

I

281.36

297.62

322.63

416.68

430.18

474.91

J

100

100

100

100

100

100

K

110

110

110

110

110

110

L

145

160

160

170

185

242

M

215

215

225

225

285

355

N

32

32

32

37

37

57

DIMENSION (MM)

SUDE 201257/1267/1357/1367SERIES

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

1357

7

6

9

8

10

C

D

B

A

5

4

M

J K

N

L

1

2

3

I

H G

E F

Sanitary Clamp Metalic Ball Valve with



FOROPEN

FORCLOSE

APPROX.TIME WT. OF

ASSYIN KGS.

1357/25/SC/AISI316L/AISI316L/SD-1000-03

1357/40/SC/AISI316L/AISI316L/SD-1000-03

1357/50/SC/AISI316L/AISI316L/SD-1000-05

1357/65/SC/AISI316L/AISI316L/SD-1000-05

1357/80/SC/AISI316L/AISI316L/SD-1000-10

1357/100/SC/AISI316L/AISI316L/SD-1000-10

25

40

50

65

80

100

10.20

10.40

12.10

14.10

22.80

30.00

Cv

66

192

434

723

1124

2100

17.00

17.00

17.00

20.00

20.00

20.00

17

17.00

17.00

20.00

20.00

20.00

.0094.05

107.15

117.07

135.73

157.95

170.25

A

34.13

41.27

49.21

59.53

65.88

86.91

B

22.22

34.92

47.62

60.32

72.62

97.63

C

72.23

81.35

98.42

107.15

114.30

127.00

D

68

68

68

95

95

123

E

117

117

117

148

148

182

F

175

175

175

250

250

261

G

247.2

256.3

273.4

357.1

364.3

388.00

H

281.36

297.62

322.63

416.68

430.18

474.91

I

100

100

100

100

100

100

J

110

110

110

110

110

110

K

145

160

160

170

185

242

L

215

215

225

225

285

355

M N

32

32

32

37

37

57

DIMENSIONS (MM)



SDTORK MAKE


12345678910

SUDE21 1257/1267/1357/1367SERIES

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

1357

7

6

9

8

10

C

D

B

A

5

4

M

J K

N

L

1

2

3

I

H G

E F



SDTORK MAKE


12345678910

I-Line Metalic Ball Valve with



FOROPEN

FORCLOSE

APPROX.TIME WT. OF

ASSYIN KGS.

1357/25/IL/AISI316L/AISI316L/SD-1000-03

1357/40/IL/AISI316L/AISI316L/SD-1000-03

1357/50/IL/AISI316L/AISI316L/SD-1000-05

1357/65/IL/AISI316L/AISI316L/SD-1000-05

1357/80/IL/AISI316L/AISI316L/SD-1000-10

1357/100/IL/AISI316L/AISI316L/SD-1000-10

25

40

50

65

80

100

10.64

10.88

12.72

15.15

22.8

30

Cv

66

192

434

723

1124

2100

17.00

17.00

17.00

20.00

20.00

20.00

17.00

17.00

17.00

20.00

20.00

20.00

A

101.99

109.93

140.49

142.08

170.65

202.00

B

34.13

41.27

49.21

59.53

65.88

86.91

C

22.22

34.92

47.62

60.32

72.62

97.63

D

72.23

81.35

98.42

107.15

114.30

127.00

E

68

68

68

95

95

123

F

117

117

117

148

148

182

G

175

175

175

250

250

261

H

247.2

256.3

273.4

357.1

364.3

388.0

I

281.36

297.62

322.63

416.68

430.18

474.91

J

100

100

100

100

100

100

K

110

110

110

110

110

110

L

145

160

160

170

185

242

M

215

215

225

225

285

355

N

32

32

32

37

37

57

DIMENSIONS (MM)

SUDE 221257/1267/1357/1367SERIES

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

1257

1

2

3

I

E H

G F

6

B

C

4

5

N

K L

O

M

A

D J

6

8

7


S.No. PART MATERIALSELECTRIC ACTUATOR STAY PUT TYPE MOTORHAND WHEELCABLE GLANDSOUTPUT BOREFLANGESCREWSEAT

SDTORK MAKE

AISI316LAISI 304SILICON

12345678


FOROPEN

FORCLOSE

OPPROX.TIME WT. OF

ASSYIN KGS.

1257/25/BW/AISI316L/AISI316L/SD-1000-03

1257/25/BW/AISI316L/AISI316L/SD-1000-03

1257/25/BW/AISI316L/AISI316L/SD-1000-03

1257/25/BW/AISI316L/AISI316L/SD-1000-03

1257/25/BW/AISI316L/AISI316L/SD-1000-05

1257/25/BW/AISI316L/AISI316L/SD-1000-05

1257/25/BW/AISI316L/AISI316L/SD-1000-10

1257/25/BW/AISI316L/AISI316L/SD-1000-10

1257/25/BW/AISI316L/AISI316L/SD-1000-20

8.6

8.7

9

9.4

10.5

12

16.7

17.2

20.5

Cv

22

80

195

250

400

840

1200

1900

3200

17.00

17.00

17.00

17.00

17.00

17.00

20.00

20.00

20.00

17.00

17.00

17.00

17.00

17.00

17.00

20.00

20.00

20.00

A

22.22

34.92

47.62

60.32

72.61

97.61

121.43

146.83

200.02

B

25.4

38.1

50.8

63.5

76.2

101.6

127

152.4

203.2

C

68.07

76.2

80.01

80.01

80.01

88.9

88.9

89.07

89.66

D

84.82

87.36

97.52

101.85

107.95

124.61

149.86

165.86

187.96

E

259.82

262.36

272.52

276.85

282.95

299.61

399.86

415.86

437.96

F

117.00

117.00

117.00

117.00

117.00

117.00

148.00

148.00

148.00

G

92.00

92.00

92.00

92.00

92.00

92.00

125.00

125.00

125.00

H

175.00

175.00

175.00

175.00

175.00

175.00

250.00

250.00

250.00

I

298.44

303.52

323.84

332.73

345.18

378.09

489.9

521.77

566.1

J

79.24

84.83

104.64

111.76

124.46

156.97

180.08

211.83

256.28

K

100

100

100

100

100

100

100

100

100

L

110.00

110.00

110.00

110.00

110.00

110.00

110.00

110.00

110.00

M

145.00

145.00

145.00

145.00

160.00

160.00

170.00

170.00

185.00

N

215.00

215.00

215.00

215.00

225.00

225.00

270.00

270.00

285.00

O

32.00

32.00

32.00

32.00

32.00

32.00

37.00

37.00

37.00

25

40

50

65

80

100

125

150

200

Butt Weld Metalic Butterfly Valve with


SUDE23 1257/1267/1357/1367SERIES

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

1257

1

2

3

H

D G

F E

6

B

4

5

M

J K

O

L

A

C I

6

8

7



SDTORK MAKE


12345678

Sanitary Clamp Metalic Butterfly Valve with



FOROPEN

FORCLOSE

OPPROX.TIME WT. OF

ASSYIN KGS.

1257/25/SC/AISI316L/AISI316L/SD-1000-03

1257/25/SC/AISI316L/AISI316L/SD-1000-03

1257/25/SC/AISI316L/AISI316L/SD-1000-03

1257/25/SC/AISI316L/AISI316L/SD-1000-03

1257/25/SC/AISI316L/AISI316L/SD-1000-05

1257/25/SC/AISI316L/AISI316L/SD-1000-05

1257/25/SC/AISI316L/AISI316L/SD-1000-10

1257/25/SC/AISI316L/AISI316L/SD-1000-10

1257/25/SC/AISI316L/AISI316L/SD-1000-20

8.8

8.85

9.4

9.8

11.00

12.5

17.2

18.00

21.2

Cv

22

80

195

250

400

840

1200

1900

3200

17.00

17.00

17.00

17.00

17.00

17.00

20.00

20.00

20.00

17.00

17.00

17.00

17.00

17.00

17.00

20.00

20.00

20.00

A

22.22

34.92

47.62

60.32

72.61

97.61

121.43

146.83

200.02

B

68.07

76.2

80.01

80.01

80.01

88.9

88.9

89.07

89.66

C

84.82

87.36

97.52

101.85

107.95

124.61

149.86

165.86

187.96

D

259.82

262.36

272.52

276.85

282.95

299.61

399.86

415.86

437.96

E

117

117.00

117.00

117.00

117.00

117.00

148.00

148.00

148.00

.00

F

92

92

92

92

92

92

125

125

125

G

175

175

175

175

175

175

250

250

250

H

298.44

303.52

323.84

332.73

345.18

378.09

489.9

521.77

566.1

I

79.24

84.83

104.64

111.76

124.46

156.97

180.08

211.83

256.28

J

100.00

100.00

100.00

100.00

100.00

100.00

100.00

100.00

100.00

K

110

110.00

110.00

110.00

110.00

110.00

110.00

110.00

110.00

.00

L

145

145.00

145.00

145.00

160.00

160.00

170.00

170.00

185.00

.00

M

215

215.00

215.00

215.00

225.00

225.00

270.00

270.00

285.00

.00

N

32.00

32.00

32.00

32.00

32.00

32.00

37.00

37.00

37.00

25

40

50

65

80

100

125

150

200

DIMENSIONS (MM)

SUDE 241257/1267/1357/1367SERIES

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

1257

6

B

4

5

M

J K

O

L

A

C I

1

2

3

H

D G

F E

6

8

7



SDTORK MAKE


12345678

I-Line Metalic Butterfly Valve with



FOROPEN

FORCLOSE

APPROX.TIME WT. OF

ASSYIN KGS.

1257/25/IL/AISI316L/AISI316L/SD-1000-03

1257/25/IL/AISI316L/AISI316L/SD-1000-03

1257/25/IL/AISI316L/AISI316L/SD-1000-03

1257/25/IL/AISI316L/AISI316L/SD-1000-03

1257/25/IL/AISI316L/AISI316L/SD-1000-05

1257/25/IL/AISI316L/AISI316L/SD-1000-05

1257/25/IL/AISI316L/AISI316L/SD-1000-10

1257/25/IL/AISI316L/AISI316L/SD-1000-10

1257/25/IL/AISI316L/AISI316L/SD-1000-20

8.96

9.02

9.68

10.16

11.4

13.2

18.24

19.2

22.84

Cv

22

80

195

250

400

840

1200

1900

3200

17

17.00

17.00

17.00

17.00

17.00

20.00

20.00

20.00

.00 17

17.00

17.00

17.00

17.00

17.00

20.00

20.00

20.00

.00

A

22.22

34.92

47.62

60.32

72.61

97.61

121.43

146.83

200.02

B

75

75

85.72

86.2

92.07

109.93

113.48

113.48

113.48

C

84.82

87.36

97.52

101.85

107.95

124.61

149.86

165.86

187.96

D

259.82

262.36

272.52

276.85

282.95

299.61

399.86

415.86

437.96

E

117.00

117.00

117.00

117.00

117.00

117.00

148.00

148.00

148.00

F

92

92.00

92.00

92.00

92.00

92.00

125.00

125.00

125.00

.00

G

175

175.00

175.00

175.00

175.00

175.00

250.00

250.00

250.00

.00

H

298.44

303.52

323.84

332.73

345.18

378.09

489.9

521.77

566.1

I

79.24

84.83

104.64

111.76

124.46

156.97

180.08

211.83

256.28

J

100

100.00

100.00

100.00

100.00

100.00

100.00

100.00

100.00

.00

K

110

110.00

110.00

110.00

110.00

110.00

110.00

110.00

110.00

.00

L

145

145.00

145.00

145.00

160.00

160.00

170.00

170.00

185.00

.00

M

215

215.00

215.00

215.00

225.00

225.00

270.00

270.00

285.00

.00

N

32

32.00

32.00

32.00

32.00

32.00

37.00

37.00

37.00

.0025

40

50

65

80

100

125

150

200

DIMENSIONS (MM)

SUDE25 1257/1267/1357/1367SERIES

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

Head Office, Bangalore CA

T/1

600/

09-1

0

NOTE : TECHNICAL SPECIFICATIONS, DETAILS & DIMENSIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. DIMENSIONS IN THE TABLE ARE APPROXIMATE SUBJECT TO FINAL CONFIRMATION BY SUDE.

vign

etgr

aphi

cs.

OUR

OTHER

PRODUCTS

Solenoid Valves.

Pneumatically operated Control Valves.

Motorised Valves.

Pneumatic & Electric Operated Ball / Butterfly valves.

Pneumatic & Motorised Dampers.

Pneumatic & Motorised VIV Dampers.

Motorised Rising & Non-rising Sluice Valve.

Heavy duty – Single phase & Three phase actuators for operating Gates & Chutes.

Pneumatic & Motorised Pinch Valve.

Pneumatic & Motorised Flush Bottom Valve.

Entire range of Electrical Actuator.

And Instrumentation Product likes Pressure Transmitter, PID Controller, Flow meter etc., for System Integration.

SUDE ENGINEERING CORPORATION

No. 1106, 10th Main Road, R.P.C. Layout,

Near R.P.C. Layout Bus Stop, Hampinagar,

Bangalore - 560 104. Karnataka, India

Pune Office :

S.No. 40/4, Balaji Udyam Nagar, Tempo Chowk,

Wadgaon Sheri, Pune 411014. Maharashtra India.

Tel. : +91 20 6533 3549 / 6531 1091Fax : +91 20 2703 1161Cell : +91 9822980003E-mail : [email protected]

Tel. : +91 80 2330 2145 / 2314 1104 / 2340 2297Fax : +91 80 2330 5729Cell : +91 9845018216E-mail : [email protected] [email protected]

SUDER

An ISO 9001:2008 Certified Company

CAT# 14 / QTY: 500 PAGES: 28 (4+24)

1257 1267 1357 1367 zero bacteria food grade valves

Technology

Transcript of 1257 1267 1357 1367 zero bacteria food grade valves