123...123 RUGGEDIZED AUTOMOTIVE PRESSURE TRANSDUCERS XTL-123E-190 (M) SERIES • Easy Installation...

123RUGGEDIZED AUTOMOTIVEPRESSURE TRANSDUCERSXTL-123B-190 (M) SERIES• Easy Installation • High Natural Frequency • 10-32 UNF or M 5 x .8 Thread • Wide Temperature Range• Compatible With Most Automotive Fluids• Patented Leadless Technology VIS®

KULITE SEMICONDUCTOR PRODUCTS, INC. • One Willow Tree Road • Leonia, New Jersey 07605 • Tel: 201 461-0900 • Fax: 201 461-0990 • http://www.kulite.com

Pressure Range1.015

1.725

3.550

7100

17250

35500

701000

1001500

210 BAR3000 PSI

Operational ModeAbsolute,

Gage, Differential

Absolute, Sealed Gage, Gage, Differential Absolute, Sealed Gage

Over Pressure 2 Times Rated Pressure to a Maximum of 4500 PSI (315 BAR)

Burst Pressure 3 Times Rated Pressure to a Maximum of 4500 PSI (315 BAR)

Pressure Media Most Liquids and Gases - Please Consult Factory (All Media May Not Be Suitable with O-Ring Supplied)

Rated Electrical Excitation 10 VDC

Maximum Electrical Excitation 12 VDC

Input Impedance 1000 Ohms (Min.), 5000 Ohms (Max.)

Output Impedance 2000 Ohms (Max.)

Full Scale Output (FSO) 100 mV ± 10 mV

Residual Unbalance ± 5mV (Typ.)

Combined Non-Linearity, Hysteresis and Repeatability ± 0.1% FSO BFSL (Typ.), ± 0.5% FSO (Max.)

Resolution Infinitesimal

Natural Frequency of SensorWithout Screen (KHz) (Typ.) Greater Than 175 KHz

Acceleration Sensitivity % FS/gPerpendicular 6.5x10-4 5.0x10-4 3.0x10-4 1.5x10-4 1.0x10-4 6.0x10-5 4.5x10-5 3.5x10-5 2.0x10-5

Insulation Resistance 100 Megohm Min. @ 50 VDC

Operating Temperature Range -40°F to +400°F (-40°C to +204°C)

Compensated Temperature Range -40°F to +350°F (-40°C to +175°C)

Thermal Zero Shift ± 1% FS/100°F (Typ.)

Thermal Sensitivity Shift ± 1% /100°F (Typ.)

Linear Vibration 10-2,000 Hz Sine, 100g. (Max.)

Mechanical Shock 20g half Sine Wave 11 msec. Duration

Electrical Connection 4 Conductor 26 AWG Shielded Viton Cable 60" Long

Weight 5 Grams (Nom.) Excluding Cable

Pressure Sensing Principle Fully Active Four Arm Wheatstone Bridge Dielectrically Isolated Silicon on Silicon Patented Leadless Technology

Mounting Torque 15 Inch-Pounds

COLOR DESIGNATIONRED + INPUT

BLACK - INPUTGREEN + OUTPUTWHITE - OUTPUT

P/N "T"190 10-32 UNF-2A

190M M 5 x .8

EN

VIR

ON

ME

NTA

LP

HY

SIC

AL

INP

UT

OU

TP

UT

Note: Custom pressure ranges, accuracies and mechanical configurations available. Dimensions are in inches. Dimensions in parenthesis are in millimeters. All dimensions nominal. (X)Continuous development and refinement of our products may result in specification changes without notice. Copyright © 2014 Kulite Semiconductor Products, Inc. All Rights Reserved.Kulite miniature pressure transducers are intended for use in test and research and development programs and are not necessarily designed to be used in production applications. For products designed to be used in production programs, please consult the factory.

.312 HEX.(7.9) .375 (9.5)

O - RING .189 (4.8)I.D. x .039 (.99) C.S.MATERIAL: VITON

.845 (21.5).15(3.8)

.15 (3.8)

.148 DIA.(3.8)

.14 (3.5)

“T”

"M" SCREEN (STANDARD)

“B” SCREEN(OPTIONAL)

# 26 AWG 4 COND.SHIELDED VITON CABLE60" (1524) LONG

.312 DIA.(7.9)

REFERENCE TUBE GAGE AND DIFFERENTIAL ONLY

.016 DIA.(.41)

Kulite recommends the KSC-2 signal conditioner to maximize the measurement capability of the XTL-123B-190 transducer.

https://www.kulite.com/products/types/signal-conditioner/

123RUGGEDIZED AUTOMOTIVEPRESSURE TRANSDUCERSXTL-123E-190 (M) SERIES • Easy Installation • High Natural Frequency • 10-32 UNF or M 5 x .8 Thread • Wide Temperature Range• Compatible With Most Automotive Fluids• Patented Leadless Technology VIS®


Pressure Range1.015

1.725

3.550

7100

17250

35500

701000

1001500

210 BAR3000 PSI


Gage,Differential




















Linear Vibration 10-2000 Hz Sine, 100g. (Max.)


Electrical Connection 4 Conductor 26 AWG Shielded Cable 60" Long




P/N "T"190 10-32 UNF-2A

190M M 5 x .8

EN

VIR

ON

ME

NTA

LP

HY

SIC

AL

INP

UT

OU

TP

UT

Note: Custom pressure ranges, accuracies and mechanical configurations available. Dimensions are in inches. Dimensions in parenthesis are in millimeters. All dimensions nominal. (E)Continuous development and refinement of our products may result in specification changes without notice. Copyright © 2015 Kulite Semiconductor Products, Inc. All Rights Reserved.Kulite miniature pressure transducers are intended for use in test and research and development programs and are not necessarily designed to be used in production applications. For products designed to be used in production programs, please consult the factory.



.312 HEX.(7.9) .252 (6.4)

O - RING .189 (4.8)I.D. x .039 (.99) C.S. MATERIAL: VITON .020 DIA. (.51)

LOCKWIRE HOLES(2 PLACES)

.750 NOM. (19.05)

.15(3.8)

.148 DIA.(3.8)

.14 (3.5)

“T”

.5 NOM. (12.7)

“B” SCREEN

# 26 AWG 4 COND.SHIELDED CABLE60" (1524) LONG

.312 DIA.(7.9)


.016 DIA.(.41)

Kulite recommends the KSC-2 signal conditioner to maximize the measurement capability of the XTL-123E-190 transducer.


RUGGEDIZED AUTOMOTIVEPRESSURE TRANSDUCERSXTL-123G-190 (M) SERIES• Easy Installation • High Natural Frequency • 10-32 UNF or M 5 x .8-6g Thread • Wide Temperature Range• Compatible With Most Automotive Fluids• Patented Leadless Technology VIS®


Pressure Range 1.015

1.725

3.550

7100

17250

35500

701000

1001500

210 BAR3000 PSI


Gage, Differential




Pressure Media All Nonconductive, Noncorrosive Liquids or Gases (Most Conductive Liquids and Gases - Please Consult Factory)
























P/N "T"190 10-32 UNF-2A

190M M 5 x .8-6g

ENVI

RO

NM

ENTA

LPH

YSIC

AL

INPU

TO

UTP

UT


Kulite recommends the KSC Series of signal conditioners to maximize the measurement capability of the XTL-123G-190 transducer.

.312 HEX.(7.9) .208

(5.28)



.750 NOM. (19.05)

.15(3.8)

.148 DIA.(3.8)

.14 (3.5)

“T”

.5 NOM. (12.7)

“B” SCREEN


.312 DIA.(7.9)


.016 DIA.(.41)



1RUGGEDIZED AUTOMOTIVEPRESSURE TRANSDUCERSXTL-142B-190 (M) SERIES• Easy Installation With Integral Connector • High Natural Frequency • 10-32 UNF or M 5 x .8 Thread • Wide Temperature Range• Compatible With Most Automotive Fluids• Patented Leadless Technology VIS®


Pressure Range1.015

1.725

3.550

7100

17250

35500

701000

210 BAR3000 PSI

Operational Mode Absolute,Gage Absolute, Sealed Gage, Gage Absolute, Sealed Gage









Residual Unbalance ± 5 mV (Typ.)




Acceleration Sensitivity % FS/gPerpendicular 6.5x10-4 5.0x10-4 3.0x10-4 1.5x10-4 1.0x10-4 6.0x10-5 4.5x10-5 2.0x10-5






Linear Vibration 100g Peak, Sine Up to 5000 Hz

Humidity 100% Relative Humidity


Electrical Connection Connnector CMR(H)-S1-E-04P or Equivalent (Mating Connector Supplied With 3 Feet of Cable)




O - RING .189 (4.8) I.D. x .039 (.99) C.S.MATERIAL: VITON

.312 HEX.(7.9)

"M" SCREEN

.375 (9.5)

.810 (20.6)

.15(3.8)

.14 (3.5)

.148 DIA.(3.7)

.285 (7.2)

.312 DIA.(7.9)

“T” CONNECTORCMR(H)-S1-E-04P OR EQUIV.

P/N "T"190 10-32 UNF-2A

190M M 5 x .8

PIN FUNCTION COLOR1 + INPUT RED2 - OUTPUT WHITE3 - INPUT BLACK4 + OUTPUT GREEN

12

43

KEYWAYDETAIL

EN

VIR

ON

ME

NTA

LP

HY

SIC

AL

INP

UT

OU

TP

UT

Note: Custom pressure ranges, accuracies and mechanical configurations available. Dimensions are in inches. Dimensions in parenthesis are in millimeters. All dimensions nominal. (R)Continuous development and refinement of our products may result in specification changes without notice. Copyright © 2014 Kulite Semiconductor Products, Inc. All Rights Reserved.Kulite miniature pressure transducers are intended for use in test and research and development programs and are not necessarily designed to be used in production applications. For products designed to be used in production programs, please consult the factory.

Kulite recommends the KSC-2 signal conditioner to maximize the measurement capability of the XTL-142B-190 transducer.


1RUGGEDIZED AUTOMOTIVEPRESSURE TRANSDUCERSXTL-142E-190 (M) SERIES• Easy Installation With Integral Connector • High Natural Frequency • 10-32 UNF or M 5 x .8 Thread • Wide Temperature Range• Compatible With Most Automotive Fluids• Patented Leadless Technology VIS®


Pressure Range1.015

1.725

3.550

7100

17250

35500

701000

210 BAR3000 PSI

Operational Mode Absolute,Gage Absolute, Sealed Gage, Gage Absolute, Sealed Gage




















Humidity 100% Relative Humidity


Electrical Connection Connnector CMR(H)-S1-E-04P or Equivalent (Mating Connector Supplied With 3 Feet of Cable)




P/N "T"190 10-32 UNF-2A

190M M 5 x .8

PIN FUNCTION COLOR1 + INPUT RED2 - OUTPUT WHITE3 - INPUT BLACK4 + OUTPUT GREEN

EN

VIR

ON

ME

NTA

LP

HY

SIC

AL

INP

UT

OU

TP

UT

Note: Custom pressure ranges, accuracies and mechanical configurations available. Dimensions are in inches. Dimensions in parenthesis are in millimeters. All dimensions nominal. (C)Continuous development and refinement of our products may result in specification changes without notice. Copyright © 2015 Kulite Semiconductor Products, Inc. All Rights Reserved.Kulite miniature pressure transducers are intended for use in test and research and development programs and are not necessarily designed to be used in production applications. For products designed to be used in production programs, please consult the factory.


.15(3.8)

CONNECTORCMR(H)-S1-E-04POR EQUIV.

.687 ± .35 (17.4)

.312 DIA.(7.9)

.305 (7.7)

12

34

KEYWAYDETAIL

.312 HEX.(7.9) .252 (6.4)

.148 DIA.(3.8)

“T”

“B” SCREEN

Kulite recommends the KSC-2 signal conditioner to maximize the measurement capability of the XTL-142E-190 transducer.


1RUGGEDIZED AUTOMOTIVEPRESSURE TRANSDUCERSXTL-163-190 (M) SERIES • Easy Installation With Integral Connector• High Natural Frequency• 10-32 UNF or M 5 x .8 Thread • Wide Temperature Range• Compatible With Most Automotive Fluids• Patented Leadless Technology VIS®


Pressure Range1.015

1.725

3.550

7100

17250

35500

701000

210 BAR3000 PSI

Operational Mode Absolute, Sealed Gage



Pressure Media Most Conductive Liquids and Gases - Please Consult Factory (All Media May Not Be Suitable With O-Ring Supplied)



Input Impedance 1000 Ohms (Min.)

Output Impedance 1000 Ohms (Nom.)

Full Scale Output (FSO) 100 mV (Nom.)











Steady Acceleration 10,000 g. (Max.)


Electrical Connection CMR-S1-E-04P Connector or Equivalent (Mating Connector Available Upon Request)




PIN FUNCTION1 + INPUT2 - OUTPUT3 - INPUT4 + OUTPUT

P/N "T"190 10-32 UNF-2A

190M M 5 x .8

.325 (8.25)

.135 (3.43)

.148 DIA.(3.7)

.273 DIA.(6.9)

“T”

.100 (2.5).275 HEX.

(6.9)

CONNECTORCMR-S1-E-04POR EQUIV.

.743 (18.9)

O - RING .147 (3.7) I.D. x .040 (1.0) C.S.MATERIAL: VITON

.157 (3.9)

.940 (23.9) MAX.

12

43

KEYWAYDETAIL

"M" SCREEN

EN

VIR

ON

ME

NTA

LP

HY

SIC

AL

INP

UT

OU

TP

UT

Note: Custom pressure ranges, accuracies and mechanical configurations available. Dimensions are in inches. Dimensions in parenthesis are in millimeters. All dimensions nominal. (L)Continuous development and refinement of our products may result in specification changes without notice. Copyright © 2014 Kulite Semiconductor Products, Inc. All Rights Reserved.Kulite miniature pressure transducers are intended for use in test and research and development programs and are not necessarily designed to be used in production applications. For products designed to be used in production programs, please consult the factory.

Kulite recommends the KSC-2 signal conditioner to maximize the measurement capability of the XTL-163-190 transducer.


# 26 AWG 4 COND.SHIELDED VITON CABLE1 METER LONG

CONNECTOR PERPTIH-10-6P OR EQUIVALENT

"B" SCREEN O - RING .189 (4.8) I.D. x .039 (1.0) C.S.MATERIAL: VITON

“T”

1.33 (33.8)

.735DIA.

(18.7)

.208 (5.28)

.15(3.8)

.148 DIA.(3.8)

.14 (3.6)

.312 HEX.(7.9)

.020 DIA. (.51) LOCKWIRE HOLES(2 PLACES)

.750 NOM. (19.05) .5 NOM.

(12.7)

.312 DIA. (7.9)


.016 DIA.(.41)

ULTRA MINIATURE 5 VDC OUTPUT DIGITALLY CORRECTED RUGGEDIZED AUTOMOTIVE PRESSURE TRANSDUCERXTL-2DC-123GA6-190 (M) SERIES • Automotive Testing Applications• Patented Leadless Technology VIS® • High Accuracy• .15% T.E.B. Typical • Compatible With Most Automotive Fluids


Pressure Range 1.015

1.725

3.550

7100

17250

35500

701000

1001500

210 BAR3000 PSI


Gage, Differential




Pressure Media All Nonconductive, Noncorrosive Liquids or Gases (Most Conductive Liquids and Gases - Please Consult Factory)

Maximum Electrical Current 25 mA (Max.)

Rated Electrical Excitation 8 - 32 VDC

Output 0 to 5 V

Output Impedance 200 Ohms (Typ.)

Total Error Band ± 0.3% (Max.) ± 0.15% (Typ.) (End Point Settings, Combined Non-Linearity, Hysteresis, Repeatability And All Thermal Effects Included)


Bandwidth (KHz) 3.5 KHz



Operating Temperature Range -40°F to +400°F (-40°C to +204°C) Amplifier -40°F to +250°F (-40°C to +121°C)




Electrical Connection 4 Conductor 26 AWG Shielded Viton Cable 1 Meter Long


Sensing Principle Fully Active Four Arm Wheatstone Bridge Dielectrically Isolated Silicon on Silicon Patented Leadless Technology

Mounting Torque 15 Inch-Pounds (Max.)

INTERNALLYCONNECTED

PIN FUNCTIONA + INPUTB +OUTPUTC -OUTPUTD -INPUT

E COMMUNICATION(FACTORY USE ONLY)

F SPARE

P/N "T"190 10-32 UNF-2A

190M M 5 x .8

ENVIR

ONME

NTAL

PHYS

ICA

LIN

PUT

OU

TPU

T

Note: Custom pressure ranges, accuracies and mechanical configurations available. Dimensions are in inches. Dimensions in parenthesis are in millimeters. All dimensions nominal. (D)Continuous development and refinement of our products may result in specification changes without notice. Copyright © 2016 Kulite Semiconductor Products, Inc. All Rights Reserved.Kulite miniature pressure transducers are intended for use in test and research and development programs and are not necessarily designed to be used in production applications. For products designed to be used in production programs, please consult the factory.

1RUGGEDIZED AUTOMOTIVEPRESSURE TRANSDUCERSXTL-HA-123B-190 (M) SERIES • Easy Installation • High Natural Frequency • 10-32 UNF or M 5 x .8 Thread • Wide Temperature Range• Compatible With Most Automotive Fluids• High Accuracy• Patented Leadless Technology VIS®

HIGH

ACCURACY


Pressure Range1.015

1.725

3.550

7100

17250

35500

701000

210 BAR3000 PSI


Gage, Differential













Natural Frequency of Sensor Without Screen (KHz) (Typ.) Greater Than 175 KHz





Total Error Band Over Compensated Temperature Range

± 2% FS BFSL, Includes Thermal Sensitivity Shift, Thermal Zero Shift And Static Error Band Over CompensatedTemperature Range (Typ.)









P/N "T"190 10-32 UNF-2A

190M M 5 x .8

EN

VIR

ON

ME

NTA

LP

HY

SIC

AL

INP

UT

OU

TP

UT

Note: Custom pressure ranges, accuracies and mechanical configurations available. Dimensions are in inches. Dimensions in parenthesis are in millimeters. All dimensions nominal. (W)Continuous development and refinement of our products may result in specification changes without notice. Copyright © 2014 Kulite Semiconductor Products, Inc. All Rights Reserved.Kulite miniature pressure transducers are intended for use in test and research and development programs and are not necessarily designed to be used in production applications. For products designed to be used in production programs, please consult the factory.

.312 HEX.(7.9) .375 (9.5)

O - RING .189 (4.8)I.D. x .039 (.99) C.S.MATERIAL: VITON

.845 (21.5).15(3.8)

.15 (3.8)

.148 DIA.(3.8)

.14 (3.5)

“T”"B" SCREEN (STANDARD)

“M” SCREEN(OPTIONAL)

# 26 AWG 4 COND.SHIELDED VITON CABLE60" (1524) LONG

.312 DIA.(7.9)


.016 DIA.(.41)

Kulite recommends the KSC-2 signal conditioner to maximize the measurement capability of the XTL-HA-123B-190 transducer.


1RUGGEDIZED AUTOMOTIVEPRESSURE TRANSDUCERSXTL-HA-123E-190 (M) SERIES • Easy Installation • High Natural Frequency • 10-32 UNF or M 5 x .8 Thread • Wide Temperature Range• Compatible With Most Automotive Fluids• High Accuracy• Patented Leadless Technology VIS®

HIGH

ACCURACY


Pressure Range1.015

1.725

3.550

7100

17250

35500

701000

210 BAR3000 PSI


Gage,Differential




Pressure Media Most Conductive Liquids and Gases - Please Consult Factory (All Media May Not Be Suitable with O-Ring Supplied)









Natural Frequency of Sensor Without Screen (KHz) (Typ.) Greater Than 175 KHz





Total Error Band Over Compensated Temperature Range

± 2% FS BFSL, Includes Thermal Sensitivity Shift, Thermal Zero Shift And Static Error Band Over CompensatedTemperature Range (Typ.)

Linear Vibration 10-2000 Hz Sine, 100g. (Max.)








P/N "T"190 10-32 UNF-2A

190M M 5 x .8

EN

VIR

ON

ME

NTA

LP

HY

SIC

AL

INP

UT

OU

TP

UT


.312 HEX.(7.9) .252 (6.4)



.750 NOM. (19.05)

.15(3.8)

.148 DIA.(3.8)

.14 (3.5)

“T”

.5 NOM. (12.7)

“B” SCREEN


.312 DIA.(7.9)


.016 DIA.(.41)

Kulite recommends the KSC-2 signal conditioner to maximize the measurement capability of the XTL-HA-123E-190 transducer.


1RUGGEDIZED AUTOMOTIVEPRESSURE TRANSDUCERSXTL-HA-142B-190 (M) SERIES • Easy Installation With Integral Connector • High Natural Frequency • 10-32 UNF or M 5 x .8 Thread • Wide Temperature Range• Compatible With Most Automotive Fluids• High Accuracy• Patented Leadless Technology VIS®

HIGH

ACCURACY


Pressure Range1.015

1.725

3.550

7100

17250

35500

701000

1402000

210 BAR3000 PSI

Operational Mode Absolute, Gage Absolute, Sealed Gage, Gage Absolute, Sealed Gage








Full Scale Output (FSO) 100 mV ± 10mV









Total Error Band Over Compensated Temperature Range, BFSL

± 2% FS, Includes Thermal Sensitivity Shift, Thermal Zero Shift And Static Error Band Over CompensatedTemperature Range (Typ.)



Electrical Connection Connector CMR(H)-S1-E-04P or Equivalent (Mating Connector Available Upon Request)




P/N "T"190 10-32 UNF-2A

190M M 5 x .8

PIN FUNCTION1 + INPUT2 - OUTPUT3 - INPUT4 + OUTPUT

CONNECTOR CMR(H)-S1-E-04POR EQUIV.


.312 HEX.(7.9)

"B" SCREEN

.375 (9.5)

.975 (24.8)

.15(3.8)

.15 (3.8)

.148 DIA.(3.7)

.285 (7.2)

.312 DIA.(7.9)

“T”

12

43

KEYWAYDETAIL

EN

VIR

ON

ME

NTA

LP

HY

SIC

AL

INP

UT

OU

TP

UT

Note: Custom pressure ranges, accuracies and mechanical configurations available. Dimensions are in inches. Dimensions in parenthesis are in millimeters. All dimensions nominal. (I)Continuous development and refinement of our products may result in specification changes without notice. Copyright © 2014 Kulite Semiconductor Products, Inc. All Rights Reserved.Kulite miniature pressure transducers are intended for use in test and research and development programs and are not necessarily designed to be used in production applications. For products designed to be used in production programs, please consult the factory.

Kulite recommends the KSC-2 signal conditioner to maximize the measurement capability of the XTL-HA-142B-190 transducer.


123...123 RUGGEDIZED AUTOMOTIVE PRESSURE TRANSDUCERS XTL-123E-190 (M) SERIES • Easy Installation...

Documents

Transcript of 123...123 RUGGEDIZED AUTOMOTIVE PRESSURE TRANSDUCERS XTL-123E-190 (M) SERIES • Easy Installation...