12 Steps 1. Wedge 2. Center 3. Drop the hole 4. Check the thickness of base leave ½ inch 5....
-
Upload
aileen-lee -
Category
Documents
-
view
212 -
download
0
Transcript of 12 Steps 1. Wedge 2. Center 3. Drop the hole 4. Check the thickness of base leave ½ inch 5....
![Page 1: 12 Steps 1. Wedge 2. Center 3. Drop the hole 4. Check the thickness of base leave ½ inch 5. Undercut base & pull up walls 6. Shape the pot 7. Trim the.](https://reader036.fdocuments.us/reader036/viewer/2022083006/56649f345503460f94c5169e/html5/thumbnails/1.jpg)
![Page 2: 12 Steps 1. Wedge 2. Center 3. Drop the hole 4. Check the thickness of base leave ½ inch 5. Undercut base & pull up walls 6. Shape the pot 7. Trim the.](https://reader036.fdocuments.us/reader036/viewer/2022083006/56649f345503460f94c5169e/html5/thumbnails/2.jpg)
12 Steps• 1. Wedge• 2. Center• 3. Drop the hole• 4. Check the
thickness of baseleave ½ inch
• 5. Undercut base & pull up walls
• 6. Shape the pot
• 7. Trim the rim, round
& smooth rim with paper towel
• 8. Remove water from inside of pot
• 9. Trim base• 10. Cut off from bat• 11. Write name on bat• 12. Clean wheel, tools &
turn off wheel.
![Page 3: 12 Steps 1. Wedge 2. Center 3. Drop the hole 4. Check the thickness of base leave ½ inch 5. Undercut base & pull up walls 6. Shape the pot 7. Trim the.](https://reader036.fdocuments.us/reader036/viewer/2022083006/56649f345503460f94c5169e/html5/thumbnails/3.jpg)
Step 1 - Throwing
• http://www.youtube.com/user/claydemo#p/a/u/0/0U8P80Ej29g
• http://www.youtube.com/user/claydemo#p/a/u/1/atos1AB84pk
![Page 4: 12 Steps 1. Wedge 2. Center 3. Drop the hole 4. Check the thickness of base leave ½ inch 5. Undercut base & pull up walls 6. Shape the pot 7. Trim the.](https://reader036.fdocuments.us/reader036/viewer/2022083006/56649f345503460f94c5169e/html5/thumbnails/4.jpg)
Trimming
• 1. Measure the thickness of the base & where foot should go
• 2. Place on wheel & center• 3. Draw the foot• 4. Trim the middle of foot• 5. Trim the outside of foot• 6. Smooth with rib & smooth needle tool hole• 7. Write your name on the bottom• 8. Sweep around wheel & make sure all tools &
stilts are put away
![Page 5: 12 Steps 1. Wedge 2. Center 3. Drop the hole 4. Check the thickness of base leave ½ inch 5. Undercut base & pull up walls 6. Shape the pot 7. Trim the.](https://reader036.fdocuments.us/reader036/viewer/2022083006/56649f345503460f94c5169e/html5/thumbnails/5.jpg)
Trimming
• http://www.youtube.com/watch?v=AAkrZ4Aqb9o&feature=related&safety_mode=true&persist_safety_mode=1
![Page 6: 12 Steps 1. Wedge 2. Center 3. Drop the hole 4. Check the thickness of base leave ½ inch 5. Undercut base & pull up walls 6. Shape the pot 7. Trim the.](https://reader036.fdocuments.us/reader036/viewer/2022083006/56649f345503460f94c5169e/html5/thumbnails/6.jpg)
Pulling up the Walls
• http://www.youtube.com/watch?v=UNR7dDJs6K4&feature=related&safety_mode=true&persist_safety_mode=1