8/11/2019 118d8a411e5a416c946533811e5e1912b5cedb18

1/11

Data sheet

Customer item no.:Communication dated: Number: ES 2982009

Doc. no.: Item no.: 100

Quantity: 1 Date: 28/05/2014Page: 1 / 11

UPA 150C-30/8 UMA 150E 7/21 Version no.: 1

Submersible borehole pump

Operating data

Design

Driver, accessories

Extension cables designed for installation in open air, laid alonga surface.

Materials Pump C1 - Materials Driver C1

Requested flow rate 25.20 m/h

Requested developed head 68.00 m

Pumped medium Water Clean waterNot containing chemical andmechanical substances which

affect the materialsAmbient air temperature 20.0 C

Fluid temperature 20.0 C

Fluid density 998 kg/m

Actual flow rate 25.20 m/h

Dev. head without non-returnvalve

68.63 m

MEI (Minimum EfficiencyIndex)

0.70

Efficiency without non-return

valve

74.8 %

Power absorbed 6.29 kW

Max. power on curve 6.59 kW

Min. allow. flow for continuousstable operation

11.79 m/h

Min. allow. flow for short termoperation

2.95 m/h

Fluid viscosity 1.00 mm/s

Dev. head with non-returnvalve

68.37 m

Flow velocity around motor 0.2 m/s

Shutoff head 89.53 m

Max. allow. flow rate 39.53 m/h

Design Single system 1 x 100 %

Pump standard Submersible bore hole pumpsDesign Close-coupledOrientation VerticalDesign according to standard Drinking water acc. to ACSConnection standarddischarge

EN 1092-2

Discharge nominal dia. DN 80Discharge norminal pressure PN 40Wear ring Casing/impeller wear ring

Impeller diameter 90.0 mm

Min. fluid level above pump 0.50 m

Non return valve withValve plate drilled NoSuction hood WithoutBearing pedestal WithoutMax. outside diameter 200.0 mmTotal length of unit 1821.0 mm

Motor size 150EDesigned for operation withfrequency inverter

No

Motor speed 2882 rpm

Frequency 50 Hz

Rated voltage 400 V

Rated power P2 7.00 kW

Available reserve 13.79 %Rated current 17.1 A

Motor enclosure IP68Cos phi at 4/4 load 0.77

Motor efficiency at 4/4 load 77.2 %

Starting mode Direct-on-line starting

Type of current Three phase (3~)Drinking water filling NoJ2 Winding No

Cable extension Connect extension cable infactory

Short cable F4Short cable cross section 2.50 mm

Length of short cable 4.00 m

Shroud type Without

Suction casing (106) Stainless steel 1.4408

Stage casing (108) Stainless steel 1.4301Pump shaft (211) Stainless steel 1.4305Clockwise impeller (232) Stainless steel 1.4301Bearing carrier (382.51) Stainless steel 1.4301Casing wear ring (502) Nitrile rubber NBR

Impeller wear ring (503) CrNiMo steel 1.4404

Bearing bush (545) Nitrile rubber NBRValve body (751) Stainless steel 1.4408Stator (81-59) Stainless steel 1.4301Motor shaft (819) 1.4021+QTMotor cable (824) CU-rubber

8/11/2019 118d8a411e5a416c946533811e5e1912b5cedb18

2/11

Data sheet

Customer item no.:Communication dated: Number: ES 2982009

Doc. no.: Item no.: 100

Quantity: 1 Date: 28/05/2014Page: 2 / 11

UPA 150C-30/8 UMA 150E 7/21 Version no.: 1

Submersible borehole pump

Nameplates

Nameplates language English

8/11/2019 118d8a411e5a416c946533811e5e1912b5cedb18

3/11

Compact data sheet

Customer item no.:

Communication dated: Number: ES 2982009

Doc. no.: Item no.:100

Quantity: 1 Date: 28/05/2014Page: 3 / 11

UPA 150C-30/8 UMA 150E 7/21 Version no.: 1

Submersible borehole pump

Design

Materials Pump C1 - Materials Driver C1

Operating data

Driver, accessories

Extension cables designed for installation in open air, laidalong a surface.

Pump standard Submersible bore holepumps

Design Close-coupledOrientation VerticalDesign according to standard Drinking water acc. to ACSConnection standarddischarge

EN 1092-2

Discharge nominal dia. DN 80Discharge norminal pressure PN 40Impeller diameter 90.0 mmMin. fluid level above pump 0.50 mNon return valve withValve plate drilled NoSuction hood WithoutBearing pedestal WithoutMax. outside diameter 200.0 mmTotal length of unit 1821.0 mm

Suction casing (106) Stainless steel 1.4408Stage casing (108) Stainless steel 1.4301Pump shaft (211) Stainless steel 1.4305Clockwise impeller (232) Stainless steel 1.4301

Pumped medium Water Clean waterNot containing chemicaland mechanicalsubstances which affect thematerials

Ambient air temperature 20.0 CFluid temperature 20.0 CActual flow rate 25.20 m/hDev. head without non-returnvalve

68.63 m

MEI (Minimum EfficiencyIndex)

0.70

Efficiency without non-return

valve

74.8 %

Power absorbed 6.29 kWDesign Single system 1 x 100 %

Designed for operation withfrequency inverter

No

Motor speed 2882 rpmFrequency 50 HzRated voltage 400 VRated power P2 7.00 kWAvailable reserve 13.79 %Rated current 17.1 AMotor enclosure IP68

Starting mode Direct-on-line startingDrinking water filling NoJ2 Winding NoShort cable F4Short cable cross section 2.50 mmLength of short cable 4.00 m

Shroud type Without

8/11/2019 118d8a411e5a416c946533811e5e1912b5cedb18

4/11

Performance curve

Customer item no.:Communication dated: Number: ES 2982009

Doc. no.: Item no.:100

Quantity: 1 Date: 28/05/2014Page: 4 / 11

UPA 150C-30/8 UMA 150E 7/21 Version no.: 1

Submersible borehole pump

0 5 10 15 20 25 30 35 40[m/h]

40

60

80

[m]

94.0/86.0

Qmin

Qmax

Totaldevelop

edhead

0 5 10 15 20 25 30 35 40[m/h]

0

50

[%]E

fficiency

0 5 10 15 20 25 30 35 40[m/h]

4

5

6

[kW]

PowerInput

Flow

Curve data

Speed of rotation 2895 rpm

Fluid density 998 kg/m

Viscosity 1.00 mm/s

Flow rate 25.20 m/h

Requested flow rate 25.20 m/hRequested developed head 68.00 m

Dev. head without non-return valve

68.63 m

MEI (Minimum EfficiencyIndex)

0.70

Efficiency without non-return valve

74.8 %

Power absorbed 6.29 kW

Curve number UPA150C3050Effective impeller diameter 90.0 mm

8/11/2019 118d8a411e5a416c946533811e5e1912b5cedb18

5/11

Speed curve

Customer item no.:

Communication dated: Number: ES 2982009

Doc. no.: Item no.:100

Quantity: 1 Date: 28/05/2014Page: 5 / 11

UPA 150C-30/8 UMA 150E 7/21 Version no.: 1

Submersible borehole pump

0 5 10 15 20 25 30 35 40[m/h]

0

20

40

60

80

100

[m]

2895 1/min

Qmin

Qmax

Totaldeveloped

head

0 5 10 15 20 25 30 35 40[m/h]

0

50

[%]E

fficiency

0 5 10 15 20 25 30 35 40[m/h]

4

5

6

[kW]

PowerInput

Flow

Curve data

Fluid density 998 kg/m

Viscosity 1.00 mm/s

Requested flow rate 25.20 m/h

Requested developed head 68.00 m

MEI (Minimum EfficiencyIndex)

0.70

Effective impeller diameter 90.0 mm

8/11/2019 118d8a411e5a416c946533811e5e1912b5cedb18

6/11

Motor data sheet

Customer item no.:Communication dated: Number: ES 2982009

Doc. no.: Item no.:100

Quantity: 1 Date: 28/05/2014Page: 6 / 11

UPA 150C-30/8 UMA 150E 7/21 Version no.: 1

Submersible borehole pump

0 1 2 3 4 5 6 7 8[kW]

2850

3000

[rpm]

n

0 1 2 3 4 5 6 7 8[kW]

0

20

40

60

80

[kW]

0.0

0.2

0.4

0.6

0.8

[1]

0

20

40

60

80

100

120

140

160

[A]

0

20

40

60

80

[%]

P1

cos phi

I

eta

mechanical power P2

Motor data

Curve data

The no-load point is not a guarantee point within the meaning of IEC 60034

Motor manufacturer KSBMotor size 150EMotor construction type Water-filled suble squirrel-

cage motorRated voltage 400 V

Frequency 50 HzMotor power 7.00 kW

Rated current 17.1 A

Rated speed 2873 rpm

Starting mode Direct-on-line startingCable standard VDESwitching frequency 15.00 1/h

Load 0.0 % 25.0 % 50.0 % 75.0 % 100.0 %

P2 0.00 kW 1.88 kW 3.75 kW 5.63 kW 7.50 kW

n 2980 rpm 2960 rpm 2936 rpm 2906 rpm 2873 rpm

P1 1.30 kW 3.02 kW 5.01 kW 7.26 kW 9.77 kW

I 10.6 A 11.2 A 12.7 A 14.9 A 18.0 AEta 0.0 % 62.1 % 74.9 % 77.5 % 76.8 %

cos phi 0.18 0.39 0.57 0.70 0.78

8/11/2019 118d8a411e5a416c946533811e5e1912b5cedb18

7/11

Installation plan

Customer item no.:Communication dated: Number: ES 2982009

Doc. no.: Item no.:100

Quantity: 1 Date: 28/05/2014Page: 7 / 11

UPA 150C-30/8 UMA 150E 7/21 Version no.: 1

Submersible borehole pump

1122

DN 80

200

1821

Drawing is not to scale Dimensions in mm

8/11/2019 118d8a411e5a416c946533811e5e1912b5cedb18

8/11

Installation plan

Customer item no.:Communication dated: Number: ES 2982009

Doc. no.: Item no.:100

Quantity: 1 Date: 28/05/2014Page: 8 / 11

UPA 150C-30/8 UMA 150E 7/21 Version no.: 1

Submersible borehole pump

Motor Connections

Weight net

Connect pipes without stress or strain! For auxiliary connections seeseparate drawing.

Note: The dimensions shownreflect the actual stagenumber. The drawing isonly symbolic.

Motor manufacturer KSBMotor size 150EMotor power 7.00 kWNumber of poles 2Speed of rotation 2882 rpm

Discharge nominal size DN2 DN 80 / EN 1092-2Rated pressure disch. PN 40

shroud 0 kgPump 20 kgMotor, cable 45 kgTotal 65 kg

8/11/2019 118d8a411e5a416c946533811e5e1912b5cedb18

9/11

Connection plan

Customer item no.:Communication dated: Number: ES 2982009

Doc. no.: Item no.:100

Quantity: 1 Date: 28/05/2014Page: 9 / 11

UPA 150C-30/8 UMA 150E 7/21 Version no.: 1

Submersible borehole pump

8/11/2019 118d8a411e5a416c946533811e5e1912b5cedb18

10/11

Text for invitation of tenders

Customer item no.:

Communication dated: Number: ES 2982009

Doc. no.: Item no.:100

Quantity: 1 Date: 28/05/2014Page: 10 / 11

UPA 150C-30/8 UMA 150E 7/21 Version no.: 1

Submersible borehole pump

Position Quantity Text for invitation of tenders

100 1 UPA 150C-30/8 UMA 150E 7/21Submersible borehole pumpMultistage centrifugal pump for vertical or horizontalinstallation. Intermediate bearing in every stage. Integeratedeays-to-remove anti-jam non-return valve. Suction strainer,drive lantern and valve body made of investment casting. Pre-filled submersible motor. Three-phase squirrel cage motorwith self-aligning thrust bearing and adequately sizedexpansion diaphragm for pressure equalisation. Design incompliance with VDE standards.UPA 150C-30/8 UMA 150E 7/21Pump type UPA 150CPumped medium Water, Clean water Max. fluid temperature 20.0 CTemperature limit forselected material max.

50.0 C

Density 998 kg/mViscosity 1.00 mm/sDev. head with non-returnvalve

68.37 m

Flow velocity around motor 0.2 m/sActual flow rate 25.20 m/hActual developed head 68.63 mPower absorbed 6.29 kWMax. power on curve 6.59 kWMin. allowable flow rate 11.79 m/hShutoff head 89.53 mMax. allow. flow rate 39.53 m/hInstallation type Close-coupledDesign according to standard Drinking water acc. to ACSStage number 8Flange connection Round flangeDischarge flange nominalpressure

PN 40

Discharge nominal dia. DN 80Non return valve withValve plate drilled NoBearing pedestal WithoutMax. outside diameter 200.0 mmTotal length of unit 1821.0 mmFrequency invertor NoMotor speed 2882 rpmFrequency 50 HzOperating voltage 400 VRated input P1 9.07 kWRated power P2 7.00 kWRated current max. 17.1 ASpeed 2895 rpmMotor pole number 2Motor enclosure IP68Cos phi at 4/4 load 0.77Motor starting mode Direct-on-line starting

8/11/2019 118d8a411e5a416c946533811e5e1912b5cedb18

11/11

Text for invitation of tenders

Customer item no.:

Communication dated: Number: ES 2982009

Doc. no.: Item no.:100

Quantity: 1 Date: 28/05/2014Page: 11 / 11

UPA 150C-30/8 UMA 150E 7/21 Version no.: 1

Submersible borehole pump

Position Quantity Text for invitation of tenders

Type of current Three phase (3~)Motor efficiency 77.2 %Motor manufacturer KSBDrinking water filling NoCable extension Connect extension cable in

factoryShort cable F4Short cable cross section 2.50 mmLength of short cable 4.00 mShroud type WithoutFinal coating WithoutColor withoutMaterial variant C1Suction casing (106) Material Stainless steel 1.4408Stage casing (108) Material Stainless steel 1.4301Pump shaft (211) Material Stainless steel 1.4305Clockwise impeller (232)Material

Stainless steel 1.4301

Bearing carrier (382.51)Material

Stainless steel 1.4301

Casing wear ring (502)Material

Nitrile rubber NBR

Impeller wear ring (503)Material

CrNiMo steel 1.4404

Bearing bush (545) Material Nitrile rubber NBRValve body (751) Material Stainless steel 1.4408Stator (81-59) Material Stainless steel 1.4301Motor shaft (819) Material 1.4021+QTMotor cable (824) Material CU-rubberShaft seal type Single acting mechanical

sealShaft seal manufacturer KSBShaft seal manufacturer type MSUShaft seal material SIC/SIC/NBR

Shaft seal type UM Mechanical seal motor side

Orientation VerticalManufacturer KSBPricegroup P16