1.1.6_SOP for Prevention of Twisted Strap in Sewing Operation & Inspection 3
Transcript of 1.1.6_SOP for Prevention of Twisted Strap in Sewing Operation & Inspection 3
SOP for Sewing of Strap, prevention of twisted strap in
sewing & inspection
Created October 2012 by CQA- Products HK
2© Triumph 17/10/2012 Title, Author
STANDARD OPERATING PROCEDURES FOR :
- Sewing of Strap
REQUIREMENTS :
l. Photocopy of every style A/D for Sewing of Strap & loop sewing operation.( Any operation which is attaching the strap to the garment.
PROCEDURES:
1. Start by comparing the bundle size with ticket & Label.
2. Check the material number, width, length, slide width according to A/D.
3. Measured the strap length, width & slide width with tape measure.
Make sure all items are correct before YOU START THE OPERATION.
4. After finished of ONE bundle, any EXECESS Strap put them back into the polybag
and return to the SUPERVISOR. Operators are NOT ALLOWED to hold or keep any
extra Strap at THE WORKPLACE.
5. Supervisor collects IMMEDIATELY ANY EXCESSIVE Strap at THE WORKPLACE of the
operator in order TO AVOID MIXING UP.
REMARK: ANY DISCREPANCY FOUND SHOULD BE RAISE UP FOR FUTHER CHECKING.
EACH AND EVERY BUNDLE MUST BE CHECK THE SAME WAY BEFORE STARTING THE OPERATION.
3© Triumph 17/10/2012 Title, Author 317/10/2012 Title, Author
Attach photo for Ref:
- Sewing of shoulder strap.
REQUIREMENTS :
l. Photocopy of every style A/D for operation of sewing shoulder strap.
II. Tape measure.
PROCEDURES:
1. Start by comparing the bundle size with sewing ticket & Label.
2. Check the material of the length, width and slide width according to A/D.
4© Triumph 17/10/2012 Title, Author
SOP for loop Sewing Operation and Strap to back
Requirement: Photo copy of A/D and shoulder strap if the strap is not included in the
bundle
• Start by checking the ticket, label compare to the A/D, measure the width and the
length of shoulderstrap, ensure that all are correct and according to the specification
• Put the pieces on top of the machine as per the correct sewing procedure and method
• Start sewing according to the instruction in the A/D of either strap to back and loop
sewing
• After completion of 40pcs, operators should check their sewing by holding 10 pcs on the
hand if there is any twisted by holding the shoulderstrap top going down to the back
cut.
• After finished one bundle any excess shoulderstrap put them back to the polybag and
return to the supervisor. Operators are not allowed to keep any excess s/s at the
workplace.
• Supervisors collect immediately any excessive s/s at the workplace of the operator in
order to avoid mixing up.
5© Triumph 17/10/2012 Title, Author
Attach photo for Ref:
-Loop sewing operation.
REMARK: ANY DISCREPANCY FOUND FROM A/D AND SEWING TICKET SHOULD BE RAISE UP
FOR FUTHER CHECKING. EACH AND EVERY BUNDLE MUST BE CHECK THE SAME WAY
BEFORE STARTING THE NEXT BUNDLE.
6© Triumph 17/10/2012 Title, Author
Sewing of operation:
• Make sure no twisted strap before & after attaching.
Example:
1st : Attach the strap to s/s top.
2nd: Attach the strap to back corner,
make sure to sliding the strap to avoid
twisting direction when attach.
7© Triumph 17/10/2012 Title, Author
Hook in strap
1. Hook in the strap to back s/s
loop.
2. Make sure no twisted strap.
8© Triumph 17/10/2012 Title, Author
Checking of strap after sewing:
•Put the pieces on the lap, check left side first then follow with right side, each time hold
5pcs of s/s to check there is no twisted strap.
9© Triumph 17/10/2012 Title, Author
STANDARD OPERATING PROCEDURES FOR :End Control & AQL Checking of strap and twisted s/s
REQUIREMENTS :
l. Photocopy of every style A/D for operation of shoulder strap sewing.
PROCEDURES:
1. Start by comparing the bundle size, style & color etc. with sewing ticket & Label.
2. Check the material of the shoulder strap, s/s width, length and slide width according to
A/D.
10© Triumph 17/10/2012 Title, Author
End control /AQL checking:
• Measured the strap length, width & slide width with tape measure.
11© Triumph 17/10/2012 Title, Author
End control / AQL checking strap checking
procedures.
A, Hold the strap firmly from the beginning till s/s top, continue the rest of the parts & repeat the same on other side.
FRONT BACK
12© Triumph 17/10/2012 Title, Author
Continue…
(Remark : the paper tag on the right hand side of the s/s must be align in a
correct placement before s/s checking)
REMARK: ANY DISCREPANCY FOUND SHOULD BE RAISE UP FOR FUTHER CHECKING.
EACH AND EVERY BUNDLE MUST BE CHECK THE SAME WAY BEFORE STARTING THE
NEXT BUNDLE