10L NEMA 4X, IP66 CCH UX Series LED Exit Signs … y...1162 US: 1-866-764-5454 CAN: 1-800-265-0502...

www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright© 2012 Cooper Crouse-Hinds1162

10L

CCH UX Series LED Exit Signs

UL ListedAvailable with Cl. I, Div. 2,Groups A, B, C, D rating

NEMA 4X, IP6610L

The Cooper Crouse-Hinds CCH UX Series LED Exit Sign combinesthe strength and durability of die cast aluminum with architecturally-pleasing aesthetics. The CCH UX Series is illuminated by LEDs,providing the customer with a long-life, low maintenance,dependable exit sign for use in conditions where reliability is crucial.

Designed for the most severe environments, the CCH UX Series willprovide maximum performance against rain, moisture, cold,corrosion, and dust in applications such as manufacturing plants,refineries, petrochemical and chemical plants, waste and sewagetreatment facilities, food processing, and other industrial facilities.

Applications:• In locations deemed hazardous due to the presence of flammable

vapors or gases• In areas where the presence of gases or vapors may become

present during an abnormal, unusual, or accidental conditions• Outdoor and wet applications• Where required by the National Electrical Code®, Life Safety

Code®, or other applicable codes

Benefits of LED Technology:• Provides safe and reliable exit marking both indoors and outdoors

during power failure or interruption of power to normal lightingsystem

• Long life (>50K hours) for years of maintenance-free operation• Energy-efficient for lower cost of operation• Low temperature operation with no loss of illumination• Rugged and durable light source for the harshest of environments

Certifications and Compliances:• NEMA 4X, UL50• UL924 wet location• IP65, IP66• Available with NEC hazardous location rating

- UL844 Class I, Division 2, Groups A, B, C, D

Temperature Performance Data:CCH UX Series Exit Sign:• -45ºC (-49ºF) to 45ºC (113ºF)CCH UX-HAZ Hazardous Location Exit Sign:• T6 rating at 45ºC (113ºF)

Ordering Information:Catalog Number Housing Finish Letter Color

CCH UX70RSDHAZ Silver Housing Red LEDCCH UX60RHAZ Silver Housing Red LEDCCH UX70GSDHAZ Silver Housing Green LEDCCH UX60GHAZ Silver Housing Green LEDCCH UX70RSD Silver Housing Red LEDCCH UX70RWHSD White Housing Red LEDCCH UX70RBKSD Black Housing Red LEDCCH UX60R Silver Housing Red LEDCCH UX60RWH White Housing Red LEDCCH UX60RBK Black Housing Red LEDCCH UX70GSD Silver Housing Green LEDCCH UX70GWHSD White Housing Green LEDCCH UX70GBKSD Black Housing Green LEDCCH UX60G Silver Housing Green LEDCCH UX60GWH White Housing Green LEDCCH UX60GBK Black Housing Green LED

Electrical Ratings:• Power Supply

120V/277V dual voltage• LED Exits - Red

Input Power120V = 2.7W277V = 3.2W

Input Current:(Max.)120V = .07A277V = .04A

• LED Exits - GreenInput Power120V = 2.3W277V = 3.0W

Input Current:(Max.)120V = .08A277V = .03A

DimensionsIn Inches:

Features and Benefits:• Wet location, outdoor rated for use in the most demanding

environments• Optional hazardous location rating available• Dual voltage 120V/277V reduces wiring errors• Heavy-duty nickel cadmium battery for long life• 24-hour charge and recharge recovery time increases safety• Heavy-duty injection molded polycarbonate lens protects against

impact and corrosion• Brown-out protection protects battery and reduces labor• Heavy-duty aluminum die cast housing protects against impact

and chemical resistance• LEDs provide long life, even illumination, and energy savings• Wide operating temperature range (-45°C to 45°C)• Self-diagnostic testing reduces costs by eliminating scheduled

equipment verification tests• Heavy duty nickel cadmium battery for long life meets 90 minute

requirements for battery operated emergency system

Mounting: wall mount, ceiling mount, end mountConduit Entry: top, bottom, or either side of the unit

www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright© 2011 Cooper Crouse-Hinds 1155

10L

10LCPMVFB EmergencyCompact FluorescentContinuous OperationChamp-Pak™ Luminaires

Cl. I, Div. 2, Groups A, B, C, DRestricted Breathing Cl. I, Div. 2 & Zone 2 (Suffix S826)Certified for IEC Zone 2 (Suffix S826TB)

Cl. II, Groups E, F, G; Cl. III &Simultaneous Presence*Marine & Wet Locations3, 3R, 4, 4X; IP66Emergency Lighting

Applications:• Where emergency lighting is required to

permit workers in industrial areas tosafely encounter their surroundingsduring power failures

• Where emergency egress lighting isrequired, such as: catwalks, walkways,tunnels, doorways, stairs, stairwells,ramps and aisles

• Indoor and outdoor wall mounting orvertical surface mounting where minimalluminaire depth is required in:– Manufacturing plants and heavyindustrial facilities– Industrial process facilities such asrefineries, chemical, petrochemical,pharmaceutical, and platforms– Waste or sewage treatment plants– Offshore, dockside, and harborinstallations

• For security and safety lighting inindustrial facilites for lighting of loadingdocks, tunnels, and stairways

• For marine, wet location, hose down,and corrosive environments

Features and Benefits:• Unique compact shallow profile design

mounts virtually anywhere• Side hinged cover with two screw

closing for easy installation andmaintenance

• Gray Corro-free™ epoxy powder coattwo-piece housing provides superiorcorrosion resistance

• Unique stainless steel wire guardaccessory attaches without anyadditional hardware for easy installationand maintenance

• Glass refractor provides uniform lightdistribution to eliminate glare

• Silicon gaskets make luminaire suitablefor NEMA 4X, marine enviroments

• High power factor ballasts (+90%) arestandard, which allow more luminairesper circuit

Standard Materials:• Luminaire housing and door frame

assembly – copper-free aluminum• External hardware – stainless steel• Lens – heat- and impact-resistant

refractor style glass• Gaskets – silicon rubber• Reflector – aluminum light sheet• Wire guard – stainless steel

Standard Finishes:• Aluminum – Corro-free™ epoxy powder coat• Stainless steel – natural

Certifications andCompliances:• NEC/CEC:

Class I, Division 2, Groups A, B, C, DClass II, Class III & SimultaneousPresence(Class I, Division 2 and Class II)Class I, Zone 2

• IEC:Zone 2 Ex nR IIC

• UL Standards:844, 2279 Hazardous (Classified)Locations1598 Luminaires1598A Marine Locations

• CSA Standards:C22.2 No. 137

• IEC Standards:60079-15

About the Battery:• Bodine fluorescent battery pack ballasts are UL component recognized• Sealed, maintenance-free, high temperature nickel cadmium• Solid state chargers are sealed inside the ballast case• 90 minute illumination time• 10-year life expectancy• 2-year full warranty• During auxiliary use 1 lamp has continuous operation• A red indicator light indicates the battery is charging• Wiring instructions for a "Push-to-Test" button is supplied with the fixture

Electrical Rating Ranges:• 52 watts• 120–277V, 50–60 Hz• 120V, 60 Hz• 347V, 60 Hz

Options:Description Suffix

Restricted breathing construction................................................................................. S826Class I, Division 2 & Zone 2 suitabilityCooler operating temperatures (T-numbers)

Certified for IEC Zone 2 (Suffix S826TB)....................................................................... S826TBFurnished with:Terminal BlockCrimp TerminalsDedicated voltage ballasts (no MT, DT or TT)

Factory assembled with lamp installed......................................................................... FAFused - projects ballast and capacitors against abnormal line conditions.................. S658

(Not for use in Canada)(Not for Marine use)

Accessories:Description Cat. #

Stainless steel wire guard............................................................................................. P55

*Consult Cooper Crouse-Hinds.

1154-1155.qxp 5/30/2011 11:16 AM Page 1155


10L

10L CPMVFB EmergencyCompact FluorescentContinuous OperationChamp-Pak™ Luminaires

Ordering InformationDimensions & Weights

Ordering Information:

Hub Size

Lamp

Watts

Cat. # for use

with ANSI Lamps

3/4 NPT 26 CPMVFB2W026


Net Weights:Luminaire Less Guard 18.6 lbs.P55 Guard 0.5 lbs.

Standard Voltage Ballasts

NEC/UL CEC/CSA (cUL)

Voltage 120–277V 50–60 Hz 120V/60 Hz 347V 60 HzSuffix /UNV /120CAN /347

1156-1157.qxp 5/30/2011 11:16 AM Page 1156


10L

10LDMVF(B) – Exit SignFluorescent Luminaire

Cl. I, Div. 2; Groups A, B, C, DRestricted Breathing Cl. I,Div. 2 & Zone 2 (Suffix S826)Certified for IEC Zone 2 (Suffix S826TB)

Cl. II, Groups E, F, G,Cl. III & Simultaneous PresenceMarine & Wet Locations3, 3R, 4X; IP66

About the Battery:• Bodine fluorescent battery pack ballasts

are UL component recognized• Sealed, maintenance-free, high

temperature nickel cadmium• Solid state chargers are sealed inside the

ballast case• 90 minute illumination time• 10-year life expectancy• 2-year full warranty• During emergency use 1 lamp has

continuous operation• A red indicator light indicates the battery

is charging• Wiring instructions for a "Push-to-Test"

button is supplied with the fixture

Energy Savings:• Less wattage used with compact

fluorescent lamps compared toequivalent incandescent lamps providingthe same light output

Standard Materials:• Ballast housings and mountings – copper-

free aluminum (less than 0.4 of 1%)• Exterior hardware – stainless steel• Globe – heat- and impact-resistant

internally fluted glass

Standard Finishes:• Aluminum – gray epoxy powder coat• Krydon material – high reflectance white• Stainless steel – natural

Electrical Rating Ranges:• 52 Watt• 120–277V, 50–60 Hz• 120V, 60 Hz• 347V, 60 Hz


Lamps supplied with exit sign............................................... S714Top hat with stainless steel threaded insert.......................... S806Restricted breathing construction.......................................... S826

Class I, Division 2 & Zone 2 suitabilityCooler operating temperatures (T-Numbers)

Certified for IEC Zone 2......................................................... S826TBFurnished with:Terminal BlockCrimp TerminalsDedicated voltage ballasts (no MT, DT or TT)

Certifications andCompliances:• NEC and CEC:

Class I, Division 2, Groups A, B, C, DClass II, Class III & SimultaneousPresence(Class I, Division 2 and Class II)Class I, Zone 2


• UL Standards:844, 2279 Hazardous (Classified)Locations1598 Luminaires1598A Marine Luminaires



Mounting

Type

Supply

Voltage

Volts/Hertz Fluorescent Cat. #

Fluorescent with

Battery Back-up Cat. #

Pendant120–277V / 50–60 Hz DMVF2A052G/UNV EXD DMVFB2A052G/UNV EXD

120V / 60 Hz (Canada) DMVFB2A052G/120CAN EXD

347V / 60 Hz DMVF2A052G/347 EXD DMVFB2A052G/347 EXD

Ceiling120–277V / 50–60 Hz DMVF2C052G/UNV EXD DMVFB2C052G/UNV EXD120V / 60 Hz (Canada) DMVFB2C052G/120CAN EXD347V / 60 Hz DMVF2C052G/347 EXD DMVFB2C052G/347 EXD

Wall120–277V / 50–60 Hz DMVF2TW052G/UNV EXD DMVFB2TW052G/UNV EXD120V / 60 Hz (Canada) DMVFB2TW052G/120CAN EXD347V / 60 Hz DMVF2TW052G/347 EXD DMVFB2TW052G/347 EXD


Applications:DMVF(B) Exit Signs are used:• In any building or enclosed area where

people work• Where illuminated exit signs are required• To provide distinct, highly visible exit

markings• To indicate the direction of travel to exits• In locations deemed hazardous due to

the presence of flammable vapors orgases, or combustible dusts

Features:• Six inch letters on white glass sign panel

make the word "exit" stand out boldlyand clearly

• Housings made of die-cast copper-freealuminum (less than 0.4 of 1% copper)for strength and resistance to corrosion

• Mounting module equipped with integralhub set-screws for vibration resistance(ceiling and pendant mounts)

• Hubs are provided with an integralconduit stop and bushing to help preventdamage to field wiring during installation

• Epoxy powder finish and stainless steelexternal hardware for resistance tocorrosion

• Long life gaskets which provide sealsbetween mounting module, housing, andglobe assembly

• Grounding wire for safety• Cool operating design• Optional emergency battery back-up

operation during power outage

1148-1149.qxp 5/30/2011 11:14 AM Page 1149


10L

DMVFB EmergencyCompact FluorescentContinuous OperationChamp® Luminaires

Cl. I, Div. 2, Groups A, B, C, DRestricted Breathing Cl. I,Div. 2 & Zone 2 (Suffix S826)Certified for IEC Zone 2 (Suffix S826TB)

Cl. II, Groups E, F, G; Cl. III &Simultaneous PresenceMarine & Wet Locations3, 3R, 4, 4X; IP66Emergency Lighting

Applications:DMVF Series Champ Lighting Luminairesare used:• Where emergency lighting is required to


• Where emergency egress lighting isrequired, such as: catwalks, walkways,tunnels, doorways, stairs, stairwells,ramps, and aisles

• In areas made hazardous by abnormalconditions resulting in the presence offlammable vapors or gases

• In areas made hazardous by thepresence of combustible dusts

• Where combustible dusts and flammablevapors are present simultaneously

• In marine applications where water sprayand corrosive atmospheres areconsiderations

• On installations where vibration andrough usage are problematic

• Where a cool, efficient light source is required

• In areas that require lamps to reach fullillumination immediately

• In refineries, chemical and petrochemicalfacilities, grain processing, handling orstorage facilities, manufacturing plants,wastewater treatment plants, sewagetreatment plants, oil terminals, foodprocessing facilities, breweries, and any other manufacturing or processingfacility where safe, reliable hazardousarea fluorescent or auxiliary lighting is needed

Standard Features:• Housings made of die-cast copper-free

aluminum (less than 0.4 of 1% copper)for strength and resistance to corrosion

• Mounting modules equipped withintegral hub set-screws for vibrationresistance (ceiling, pendant, and quadmounts)

• Hubs are provided with an integralconduit stop and bushing to help preventdamage to field wiring during installation

• Epoxy powder finish and stainless steelexternal hardware for resistance tocorrosion

• Long-life gaskets which provide sealsbetween mounting module, housing,and optical assembly

• Grounding wire for safety• Cool operating design• Optional stainless steel open bottom

guard permits direct access to the globefor easy relamping

• Battery pack ballast for emergencylighting

Energy Savings• Less wattage used with compact

fluorescent lamps compared toequivalent incandescent lampsproviding the same light output

About the Battery (DMVFB Units):• Bodine fluorescent battery pack ballasts


temperature nickel cadmium• Solid state chargers are sealed inside

the ballast case• 90 minute illumination time• 10-year life expectancy• 2-year full warranty• During auxiliary use 1 lamp has

continuous operation• A red indicator light indicates the battery


button is supplied with the fixture

Standard Materials:• Ballast housings and mountings – copper-

free aluminum (less than 0.4 of 1%)• External hardware guards – stainless steel• Reflectors – Krydon® fiberglass-

reinforced polyester material• Globe – heat- and impact-resistant

internally fluted glass

Standard Finishes:• Aluminum – gray epoxy powder coat• Krydon material – high reflectance white• Stainless steel – natural

Electrical Rating Ranges:• 52, 64, and 84 watts• 120–277V, 50–60 Hz• 347V, 60 Hz


Class I, Division 2, Groups A, B, C, DClass II, Class III & Simultaneous Presence (Class I,Division 2 and Class II)Class I, Zone 2Emergency Lighting


• UL Standards:844, 2279 Hazardous (Classified)Locations1598 Luminaires1598A Marine Locations924 Emergency Lighting




• Restricted breathingconstruction................................ S826-Class I, Division 2 & Zone 2 suitability-Cooler operating temperatures(T-numbers)

• Certified for IEC Zone 2............. S826TB-Furnished with:Terminal BlockCrimp Terminals

• Emergency operation only –Consult Cooper-Hinds

• Factory assembled with lampinstalled....................................... FA

• Fused – to protect ballastagainst abnormal line conditions(not for use in Canada) (not formarine use).................................. S658

• Lamps supplied with luminaire... S714• Top hat with stainless steel

threaded insert to attach ballasthousing........................................ S806

• TEFLON® coating on globe forincreased shatter protection....... S808

Accessories:(Order separately)Description Cat. #

Dome RD73930° Angle RA739

10L

1156-1157.qxp 5/30/2011 11:16 AM Page 1157


10L

10L

Mounting

Style

Hub

Size (In.)

Lamp

Watts

DMVFB Series

Fluorescent with Battery

Back-Up with G303 Globe

and P33 Guard

Cat. #

Pendant Mount 3/4 52 DMVFB2A052GP

1 DMVFB3A052GP3/4 64 DMVFB2A064GP1 DMVFB3A064GP3/4 84 DMVFB2A084GP1 DMVFB3A084GP

Flexible Pendant

Mount

3/4 52 DMVFB2HA052GP3/4 64 DMVFB2HA064GP3/4 84 DMVFB2HA084GP

Ceiling Mount

Thru-Feed

3/4 52 DMVFB2C052GP

1 DMVFB3C052GP3/4 64 DMVFB2C064GP1 DMVFB3C064GP3/4 84 DMVFB2C084GP1 DMVFB3C084GP

Wall Mount

Thru-Feed

3/4 52 DMVFB2TW052GP

1 DMVFB3TW052GP3/4 64 DMVFB2TW064GP1 DMVFB3TW064GP3/4 84 DMVFB2TW084GP1 DMVFB3TW084GP

Quad-Mount 3/4 52 DMVFB25Q052GP

Pendant, AdjustableThru-Feed, 25° Angle,121/2° Angle

3/4 64 DMVFB25Q064GP3/4 84 DMVFB25Q084GP

Stanchion Mount 11/2 52 DMVFBJ052GP25° Angle 11/2 64 DMVFBJ064GP

11/2 84 DMVFBJ084GP

Stanchion Mount 11/2 52 DMVFBP052GPStraight 11/2 64 DMVFBP064GP

11/2 84 DMVFBP084GP

1. Catalog numbers are basic numbers. Voltage must be specified.

Standard Voltage Ballasts


1. Voltage 120–277V 50–60 Hz 120V/60 Hz 347V 60 HzSuffix /UNV /120CAN /347

Note: For technical information on family

trees, temperature performance data,

dimensions, weights, and photometrics,

refer to Series in Section 6L.

DMVFB EmergencyCompact FluorescentContinuous OperationChamp® Luminaires

Cl. I, Div. 2, Groups A, B, C, DRestricted Breathing Cl. I,Div. 2 & Zone 2 (Suffix S826)Certified for IEC Zone 2 (Suffix S826TB)

Cl. II, Groups E, F, G; Cl. III &Simultaneous PresenceMarine & Wet Locations3, 3R, 4, 4X; IP66Emergency Lighting

1158-1159.qxp 5/30/2011 11:17 AM Page 1158


10L

EVLPF(B) – Exit SignFluorescent Luminaire

Cl. I, Div. 1, Groups B (suffix GB), C, DCl. I, Zone 1, Groups IIB + H2

(GB suffix), IIBCl. II, Div. 1, Groups E, F, G; Class III,Simultaneous Presence

Marine & WetLocations3, 3R, 4, 4X;IP66

Applications:EVLPF(B)-EXD Exit Signs are used:• In any building or enclosed area where

people work – where illuminated exitsigns are required

• To provide distinct, highly visible exitmarking

• To indicate the direction of travel to exits• In locations deemed hazardous due to

the presence of flammable vapors,gases, or combustible dusts

Features and Benefits:• Six inch red letters on white glass sign

panel make the word "EXIT" stand outboldly and clearly

• Lightweight copper-free aluminumhousing with powdered epoxy finish

• All exterior hardware is corrosion-resistant stainless steel

• Three mounting arrangements: pendant,ceiling, and wall bracket

• Integral ballast• High power factor (90%+) ballasts• Easier assembly, installation, and

maintenance• Outdoor, hose down, marine and

corrosive environments suitable• Ideal for adverse environments typical of

industrial facilities• Ground wire for safety• Optional battery back-up for operation

during power outage

About the Battery:• Bodine fluorescent battery pack ballasts


temperature nickel cadmium• Solid state chargers are sealed inside

the ballast case• 90 minute illumination time• 10-year life expectancy• 2-year full warranty• During emergency use 1 lamp has

continuous operation• Red indicator light indicates the battery


button is supplied with the luminaire

Standard Materials:• Mounting modules, cover, ballast

housing, globe holder – copper-freealuminum

• Globe – heat- and impact-resistant glass• Exterior hardware – stainless steel

Standard Finishes:• Copper-free aluminum – Corro-free™

powdered epoxy

Ratings (Electrical/Size):Sources/wattage:

• 52W (2-26W lamps)• 120-277V, 50-60 Hz• 120V, 60 Hz• 347V, 60 HzConduit entries:

• 3/4", 1" NPT – pendant, wall bracket,ceiling

Certifications andCompliances:• NEC and CEC:

Class I, Division 1, Groups B (GBsuffix), C, DClass I, Zone 1, Groups IIB + H2 (GBSuffix), IIB, IIAClass II, Class III & SimultaneousPresence (Class I and Class II)

• UL Standards:844 Hazardous (Classified) Locations1598 Luminaires1598A Marine Locations



Group B suitability GBFactory assembled with lamps FA

10L

Energy Savings:• Less wattage used with compact



Mounting

Type

Supply

Voltage

Volts/Hertz Fluorescent Cat. #

Fluorescent with

Battery Back-up Cat. #

Pendant120–277V / 50–60 Hz EVLPFA02520/UNV EXD EVLPFBA02520/UNV EXD120V / 60 Hz (Canada) EVLPFBA02520/120CAN EXD347V / 60 Hz EVLPFA02520/347 EXD EVLPFBA02520/347 EXD

Ceiling120–277V / 50–60 Hz EVLPFCX02520/UNV EXD EVLPFBCX02520/UNV EXD120V / 60 Hz (Canada) EVLPFBCX02520/120CAN EXD347V / 60 Hz EVLPFCX02520/347 EXD EVLPFBCX02520/347 EXD

Wall120–277V / 50–60 Hz EVLPFBX02520/UNV EXD EVLPFBBX02520/UNV EXD120V / 60 Hz (Canada) EVLPFBBX02520/120CAN EXD347V / 60 Hz EVLPFBX02520/347 EXD EVLPFBBX02520/347 EXD

1148-1149.qxp 5/30/2011 11:14 AM Page 1148


10L

EVLPFB EmergencyCompact FluorescentContinuous OperationLow Profile Luminaires

Cl. I, Div. 1, Groups B (GB Suffix), C, DCl. I, Zone 1, Groups IIB + H2

(GB suffix), IIB, IIACl. II, Div. 1, Groups E, F, G; Class III,Simultaneous Presence

Marine & WetLocations3, 3R, 4, 4X; IP66Emergency Lighting

Applications:Cooper Crouse-Hinds Low ProfileHazard•Gard® Luminaires are used in:• Areas that require lamps to reach full

lumination immediately• Where emergency lighting is required to


• Where emergency lighting is requiredsuch as: catwalks, walkways, tunnels,doorways, stairs, stairwells, ramps, andaisles

• Areas where flammable or explosivevapors or gases are present

• Hazardous areas, both indoors andoutdoors, where long life and lowmaintenance costs are desired

• Petroleum refineries, chemical,petrochemical and pharmaceuticalplants, oil terminals, gas plants andother heavy process industry facilities

• Waste treatment facilities• Drilling platforms and other coastal and

offshore hazardous areas

Features and Benefits:• Small, compact size• Two start Acme threaded construction• Easier assembly, installation, and

maintenance• Lightweight copper-free aluminum

housing with powdered epoxy finish• All exterior hardware is corrosion-

resistant stainless steel• Four mounting arrangements: pendant,

ceiling, wall bracket, and stanchion• Integral ballast• High power factor (90%+) ballasts• Uses same mounting modules as the

standard Hazard•Gard®

• Internally fluted glass globes• Krydon® construction dome and angle

reflectors – won't rust, corrode, dent,chip, or peel

• Now available in components – luminairebody, mounting module, guard,reflectors

• Three wire construction• For energy conservation, luminaires can

be switched off without affecting theemergency operation feature

Standard Materials:• Mounting modules, cover, ballast

housing, globe holder – copper-freealuminum

• Globe – heat- and impact-resistant glass• Exterior hardware – stainless steel• Reflectors (dome & angle) – Krydon®

fiberglass-reinforced polyester

Standard Finishes:• Copper-free aluminum – Corro-free™

powdered epoxy• Krydon – white• Stainless steel guard

Energy Savings• Less wattage used with compact


Ratings (Electrical/Size):Sources/Wattage:

• Fluorescent continuous operationemergency lighting 52W (2-26W lamps)and 64W (2-32W lamps) compactfluorescent voltages

• Fluorescent emergency lighting120–277V, 50–60 Hz120V, 60 Hz347V 60Hz

Conduit entries:

• 3/4", 1" NPT – pendant, wall bracket,ceiling

• 11/4" NPT – stanchion


Class I, Division 1, Groups B (with GB suffix), C, DClass I, Zone 1, Groups IIB + H2

(GB Suffix), IIB, IIAClass II, Class III & SimultaneousPresence(Class I and Class II)Emergency Lighting

• UL Standards:844 Hazardous (Classified) Locations1598 Luminaires1598A Marine Locations924 Emergency Lighting



Group B suitability GBFused (not for use in Canada) (not for marine use) S658*Factory assembled with lamps FAEmergency operation only – Consult Cooper Crouse-Hinds*When ordering fuses for luminaires, option S658, you must specify the operating voltage. S658 cannot beordered with /MT in the catalog number.

Accessories:Description Cat. #

Dome reflector RD739Angle reflector RA739

About the Battery:• Bodine fluorescent battery pack ballasts are UL component recognized• Sealed, maintenance-free, high temperature nickel cadmium• Solid state chargers are sealed inside the ballast case; 90 minute illumination time; 10-year

life expectancy• 2-year warranty• During emergency use, 1 lamp has continuous operation• A red indicator light indicates the battery is charging• Wiring instructions for a "Push-to-Test" button is supplied with the fixture

10L

1158-1159.qxp 5/30/2011 11:17 AM Page 1159


10L

10L EVLPFB EmergencyCompact FluorescentContinuous OperationLow Profile Luminaires

Cl. I, Div. 1, Groups B (GB Suffix), C, DCl. I, Zone 1, Groups IIB + H2

(GB suffix), IIB, IIACl. II, Div. 1, Groups E, F, G; Class III,Simultaneous Presence

Marine & WetLocations3, 3R, 4, 4X; IP66Emergency Lighting

Pendant Mount

Wall Bracket Mount†

Ceiling Mount†

Stanchion Mount

†Ceiling and bracket mounts have 4 hubs: 3 are plugged.

Complete Catalog Numbers as follows:Standard Voltage Ballasts


1. Voltage 120–277V 50–60 Hz 120V/60 Hz 347V 60 HzSuffix /UNV /120CAN /347

Example: EVLPFB02521/UNV

2. Other Voltages – Consult Cooper Crouse-Hinds

Note: For technical information on family trees, temperature performance data, dimensions,

weights, and photometrics, refer to DMVF Series in Section 6L.

EVFPFB Fluorescent Emergency Lighting

• Three wire construction, for switching purposes, is standard on fluorescent emergency lighting.• For energy conservation, luminaires can be switched off without affecting the emergency operation

feature.

*Test switch is remote mounted.Use Cooper Crouse-Hinds EDSC218 (Not furnished).


Pendant Wall Bracket† Ceiling† Stanchion

Luminaire

Body

Less

Mounting

Module &

Guard

Watt

Hub

Size

(In.)

With Guard

Cat. #

With Guard

Cat. #

With Guard

Cat. #

With Guard

Cat. # Cat. #

Fluorescent with Emergency Ballast – High Power Factor Ballast (Min. P.F. 90%)

52W

3/4 EVLPFBA02521 EVLPFBBX02521 EVLPFBCX02521 EVLPFB05201 EVLPFBA03521 EVLPFBBX03521 EVLPFBCX0352111/4 EVLPFBJ04521

64W3/4 EVLPFBA02641 EVLPFBBX02641 EVLPFBCX02641 EVLPFB06401 EVLPFBA03641 EVLPFBBX03641 EVLPFBCX0364111/4 EVLPFBJ04641

1160-1161.qxp 5/30/2011 11:17 AM Page 1160


10L

EXL Explosionproof Exit Sign

Factory-sealed

Cl. I, Div. 1 & 2, Groups C, DCl. I, Zone 1 IIBCl. II, Div. 1, Groups E, F, G

Applications:EXL Exit Signs are used:• In locations deemed hazardous due to

the presence of flammable vapors orgases, or combustible dusts

• In any building or enclosed area wherepeople work – where illuminated exitsigns are required

• To provide distinct, highly visible exitmarking

• To indicate the direction of travel to exits

Features:• Two incandescent lamps (not included)

wired in parallel – to provide extramargin of light source reliability

• Solid state circuit for extended lamp lifein AC units

• Six inch red letters on white acrylic signpanel make word "exit" stand out boldlyand clearly

• Edge lighting characteristic of sign panelmakes visibility excellent at all lightinglevels

• Factory-sealed explosionproof housing• Pendant, wall, and end bracket mounts

provide universal installation options• Impact-resistant acrylic sign panel needs

no guard – makes cleaning easy• Internal rectifier extends lamp life

beyond 1,000-hour rated life – reducesrelamping cost

• Relamping tool provided

Standard Materials:• Body – copper-free aluminum• Sign panel – acrylic

Conduit Entrance:• 3/4" hubs

Lamp Wattage:• Two 60 watt, 60T10 clear lamps for AC units• Two 25 watt, 25T10 clear lamps for DC units• Lamps not included with luminaire

Electrical Ratings:• 120VDC or 120VAC operation

Certifications andCompliances:• NEC:

Class I, Groups C, DClass II, Groups E, F, G

• UL Standard: 844• NFPA Life Safety Code No. 101-1991

Ordering Information:When ordering an EXL Series Exit Sign,you will need to specify:

(A) Voltage (120VAC or 120VDC)(B) Mounting (Wall, End Bracket, or

Pendant)(C) Exit Sign Designation

All units come standard with 3/4" hubs andexit signs with red lettering and whitebackground. Complete catalog numberingis as follows:

EXL (A) 2 (B) (C)(A) Voltage: 120VAC............ leave blank

120VDC .......................... D(B) Mounting: Wall................................. 1

End Bracket.................... 2Pendant .......................... 3

(C) Exit Sign Designation:A Single Face (Wall Mount)AA Double Face (End Bracket

& Pendant)AB Double Face, one side

arrowhead right, the otherno arrowhead (End Bracket& Pendant)

AC Double Face, one sidearrowhead left, the other noarrowheads (End Bracket &Pendant)

AD Double Face, one sidearrowhead both ends, theother no arrowheads (EndBracket & Pendant)

B Single Face, arrowheadright (Wall Mount)

BC Double Face, one sidearrowhead right, the otherarrowhead left (End Bracket& Pendant)

BD Double Face, one sidearrowhead both ends, theother arrowhead right (EndBracket & Pendant)

C Single Face, arrowhead left(Wall Mount)

CD Double Face, one sidearrowhead both ends, theother arrowhead left (EndBracket & Pendant)

D Single Face, arrowheadboth ends (Wall Mount)

DD Double Face, both sidesarrowhead both ends (EndBracket & Pendant)

10L

Pendant Style

End Bracket Style

Wall Style

Mounting

Type

Sign Panel

Description

Hub

Size (In.)

AC

Cat. #

DC

Cat. #

Wall Single face 3/4 EXL21A EXLD21A

End Bracket Double face 3/4 EXL22AA EXLD22AA

Pendant Double face 3/4 EXL23AA EXLD23AA


Exit signs with green lettering on white background........................................................ GNUnit provided with epoxy powder coat............................................................................. S752277VAC – (Order ECT413 Transformer Separately)

Temperature PerformanceData:(for both AC & DC operation):Ambient

Temp. (°C)

Class I (C, D)

Class II (E, F, G)

Supply

Wire °C

25 T3C 150°C40 T3C

1146-1147.qxp 5/30/2011 11:14 AM Page 1146


10L

10LEXL Explosionproof Exit Sign

Factory-sealedDimensions

Pendant Style Wall Style

End Bracket Style


1146-1147.qxp 5/30/2011 11:14 AM 47


10L

Ex-Lite LED Exit Signs Cl. I, Div. 2, Groups A, B, C, DCl. I, Zone 1, AEx em ib IIC (NEC)Cl. I, Zone 1, Ex em ib IIC (CEC)Cl. II, Div. 2, Groups F, G (NEC)Cl. II, Div. 2, Groups E, F, G (CEC)

UL ListedIP66

The Ex-Lite Series of LED exit signs aredesigned for hazardous locations and areideally suited for marking escape routesand exits in potentially explosiveatmospheres.

The Ex-Lite Z is available as an AC onlyversion, while the Ex-Lite ZE is availablewith self-contained battery. As anemergency lighting luminaire with self-contained battery system, the Ex-Lite ZEfeatures a nickel cadmium battery withautomatic test and monitoring feature.

Applications:• In harsh and hazardous environments

where illuminated exit signs are required

Features and Benefits:LED Technology:

• Long life (>50K hours) for years ofmaintenance-free operation

• Energy-efficient for lower cost ofoperation

• Low temperature operation with no lossof illumination

• Rugged and durable light source for theharshest of environments

Exit Sign System:

• Can be used in a hazardous location• Conduit or cable entry• Can be installed in moist, humid, rain,

and wet environments• Universal input voltage 110VAC-277VAC

and 110VDC-250VDC reduces inventory• Ex-Lite ZE with self-monitoring, self-

diagnostic, and test capability• Premium heavy-duty nickel cadmium

battery• 24-hour charge and recharge time

increases safety by recovering quicklyfrom outage

• "EXIT" legend with alternative wings -left, right, or left and right; simple fieldmodification

• Emergency lighting cycle three hours• The housing of the luminaire is

constructed with a corrosion resistant,robust, lightweight aluminum alloymaterial and illumination of the sign isprovided with red, high-efficient LEDs

Certifications andCompliances:• Class I, Division 2, Groups A, B, C, D• Class I, Zone 1, AEx em ib IIC (NEC)• Class I, Zone 1, Ex em ib IIC (CEC)• Class II, Division 2, Groups F, G (NEC)• Class II, Division 2, Groups E, F, G

(CEC)• IP66• UL844• UL924/CSA22.2 No. 141-02• UL60079/CSA22.2 E60079• UL1203/CSA22.2 E6124-1-1-02

DimensionsIn (mm):

10L


Catalog Number Ex Lite Z Ex Lite ZE

Description AC/DC Exit Sign with Battery

Light Source LED LEDLife of LED 50K hours 50K hoursRated Voltage, VAC 120V-277V 120V-277VFrequency, Hz 50/60 50/60Rated Voltage, DC 110V-250V 110V-250VPower Consumption 6VA 6VABattery N/A NiCad

Allowable Temperature Range -4ºF to 122ºF(-20ºC to 50ºC)

41ºF to 95ºF(5ºC to 35ºC)*

Mounting Wall WallCable Entry Ex-e Ex-eConduit Entry 3/4" 3/4"Protection IP66 IP66

*Due to battery chemistry, the charging capacity will be limited at temperatures below 5ºC and above 35ºC.

Material Number 12191001005 12191130005


10L

10L ELPS Light-Pak™

Emergency LightingSystem

Cl. I, Div. 1 & 2, Groups C, DCl. I, Div. 1 & 2, Groups B, C, D(with suffix GB)Cl. II, Div. 1, Groups E, F, GCl. III

Cl. I, Zone 1Simultaneous PresenceWet LocationsNEMA 3, 3R, 12

Applications:ELPS Series Emergency Lighting Systemsare used:• To provide safe, reliable illumination

indoors or outdoors to designated areasduring failure or interruption of power tothe normal lighting system

• In areas made hazardous by thepresence of flammable gases andvapors, combustible dusts, or easilyignitible fibers and flyings

• In areas where corrosion, vibration,moisture, dirt, and rough usage may beencountered

• Where required by the National ElectricalCode®, the Life Safety Code, or othercodes

• In refineries, chemical and petrochemicalfacilities, grain processing, handling orstorage facilities, manufacturing plants,wastewater treatment facilities, andother areas where safe, reliable,hazardous area emergency lighting isneeded

Features:• Compact factory-sealed luminaire

assemblies are each furnished with a 12watt tungsten-halogen lamp and innerreflector for appropriate photometrics inhazardous areas

• Luminaire assemblies are fully adjustableand lockable on two axes to provideflexible and consistent light aimingcapabilities

• Luminaire lens ring is threaded for easyrelamping and locks in place with hexhead set-screw; will not loosen due tovibration

• Ground joint cover with external flangedesign permits large opening and easyaccess to internal components; studbolts in diagonally opposite corners ofbody ease cover removal and installation

• Neoprene cover gasket seals outmoisture for superior protection ofinternal components against wetnessand corrosion

• Lightweight, compact size, andmounting feet ease installation and allowplacement in confined areas

• Two 1" NPT drilled and tapped conduitopenings, with plugs, are standard, forchoice of top or bottom feed

• Factory-installed PUSH-TO-TESTpushbutton enables easy testing ofsystem

• MAIN POWER ON pilot light indicatesAC power is being supplied to thebattery charger; pilot light jewel isthreaded for easy lamp replacement

• Stainless steel drain minimizes moisturecollection; stainless steel breather withaluminum cap provides ventilation,minimizes moisture collection

• CID 101 corrosion inhibitor device isprovided with each ELPS system to helpprotect electrical components andconnections

• Rugged, long-life, maintenance-free,nickel cadmium battery provides 30watts of power for the required 11/2 hours

• Solid state battery charger for long lifeand reliable service prevents deepdischarge by automaticallydisconnecting luminaires from battery Electrical Ratings:

• Power Supply:Input:

120, 220/240, 277 VAC, 50 or 60 Hz0.5 Amps Maximum

Output: 12 VDCUL listed for 28 watts for 11/2 hours at 0° –40°C

• Luminaires:Voltage: 12 VDCLamp Type: #789, miniatureTungsten halogen, G4, 2-pin, 14 watt

Standard Materials:• Power supply enclosure and luminaire

assembly – copper-free aluminum (lessthan 0.4 of 1% copper)

Standard Finishes:• Power supply enclosure and fixture

assemblies – powder coat epoxy paintfinish


• Remote mounted lamp head and arm....EVLA12• Key operated disconnect switch

as part of the ELPS502 emergency light system .......................... S794

• Keyless operated designateddisconnect switch as part of theELPS502 emergency light system .......... S854

Ordering Information:Description Cat. #

• Standard unit withadjustable heads............ ELPS502†

• Replacement powerinterior, includes circuitboard and battery pack ELPS K50

• Power supply ................. ELPS50†

• Lamphead and arm ....... EVLA12†• Exit sign, double sided

with EVI, red letters........ ELPS502 EXD• Exit sign, double sided

with EVI, green letters.... ELPS502 EXD GN• Exit sign, single or

double sided withGroup B EVA, red letters....................... ELPS502 EXD GB

• Exit sign, single or

double sided withGroup B EVA, greenletters ............................. ELPS502 EXD GB GN

• Exit sign, single sidedwith EVI, red letters........ ELPS502 EXS

• Exit sign, single sided with EVI, green letters................... ELPS502 EXS GN

†Base unit comes standard with Class I, Division 1, Group B.

Certifications andCompliances:• NEC:

Class I, Groups B, C, DClass II, Groups E, F, GClass IIISimultaneous Presence

• NEMA: 3R, 12 (ELPS power supply)• Suitable for wet locations (EVLA fixtures)• Marine (EVLA fixtures)• UL Standard:

844 – Electric Luminaire – HazardousLocations924 – Emergency Lighting and PowerEquipment1203 – Explosionproof and Dust-Ignitionproof Electrical Equipment

• Life Safety Code:Section 5-9 (Emergency Lighting)

• Suitable for Wet Locations• NEMA 3, 3R, 12• Marine

• Terminal block facilitates field wiringconnections

• Instruction sheet and maintenancerecord card provided with unit in aprotective plastic envelope

• A time delay is standard; time delay ispreset at factory for 5 minute delay butcan be field set for 5 seconds or 15minutes, thus allowing HID type lampstime to restrike and reach desiredillumination levels

• Solid state battery charger will accept120, 220/240 or 277 VAC, 50/60 Hz

1150-1151.qxp 5/30/2011 11:15 AM Page 1150


10L

ELPS Light-Pak™

Emergency Lighting SystemTemperature Performance DataPhotometric DataDimensions and Weights

Temperature Performance Data:Cat. # Class T-number

Maximum Ambient Temperature 55°C

EVLA12I T4AII* T3BIII* T3B

Maximum Ambient Temperature 40°C

ELPS EVI T3CT4

ELPS EVA T3CT4

*For Class II and Class III applications, fixtures must not be aimed more than 30° abovehorizontal (see diagram below).

Photometric Data:

Unit Net Weights:• ELPS502 complete emergency lighting system – 50 lbs.• ELPS50 power supply – 40 lbs.• EVLA12 luminaire assembly – 5 lbs.

Status Indication:LED Status Condition Meaning of the Indication

No light AC power is removed from the circuit

• Steady light (no blinking) Fully charged

• Light blinks once Charging

•• Light blinks twice Battery failure

••• Light blinks three times Circuit failure•••• Light blinks four times Lamp failure

10L


1150-1151.qxp 5/30/2011 11:15 AM Page 1151


10L

LED N2LPS LIGHT-PAK™

Emergency Lighting SystemCl. I, Div. 2, Groups B, C, DCl. I, Zone 2Wet Locations, MarineNEMA 3, 3R, 4XAmbient 0ºC to 55ºC

Applications:LED N2LPS Light-Pak™ emergency lightingsystems are used:• To provide reliable illumination for

egress areas during failure orinterruption of power to the normallighting system

• In areas where flammable gases orvapors may become present due toabnormal, unusual, or accidentalconditions

• In manufacturing plants, refineries,petrochemical and chemical plants,waste and sewage treatment facilities,oil terminals, food processing facilities,breweries, and other industrialmanufacturing or process industryfacilities subject to wet or corrosiveconditions

• To illuminate machinery or panels duringa loss of AC power

• Where moisture, dirt, dust, or corrosionwill limit the life and reliability of ordinaryemergency lighting systems

• Where required by the NationalElectrical Code®, the Life Safety Code®

or other applicable codes• Outdoor applications

Features:• Compact, factory-assembled luminaire

featuring LED lamps for improved lumenperformance, on-time, and lamp life

• Nonmetallic, enclosed, and gasketedhousing provides corrosion protection inthe most extreme environments

• Durable and marine rated LED lamphead assemblies provide protectionagainst water ingress, corrosion, andimpact

• High temperature rated nickel cadmiumbattery for reliable operation up to 55ºCambient

• Solid state battery charger for long lifeand reliable battery operation preventsdeep discharge by automaticallydisconnecting the battery from theluminaire

• Factory-installed "push-to-test" button• Self-test, monitoring, and diagnostics

reduce costly maintenance checks• Remote luminaire head assemblies (one

or two) are available for mounting ofluminaire heads away from main powersystem

• Stainless steel drain minimizes moisturecollection

• Standard battery disconnect switch(Krydon® unit)

Temperature PerformanceData:Based on 55°C ambient

Cat. # Class I, Division 2

N2LPS (all) 40ºC - T5; 55ºC - T4AN2RF (all) T5Note: Ambient temperature at which the Light-Pak

system is rated is 0°C to 55°C. Operation attemperatures outside this range will affect thebattery life and/or charging performance.

National Electrical Code and Life Safety Code areregistered trademarks of the National Fire ProtectionAssociation, Inc.Noryl is a registered trademark of General ElectricCompany.

Standard Materials:• Power supply and remote luminaire

enclosures – Krydon® fiberglass-reinforced polyester

• LED lamp head assembly – epoxypowder coated stainless steel

• Exterior hardware – nylon, plasticcoated, and stainless steel

• Cover gasket – Hypalon® synthetic rubber

Electrical Ratings:• Power supply –

Input: 120, 220, 230, 240, or 277 VAC,50 or 60 Hz; 28 watts max.Output: 12 VDC

• Luminaire heads – Voltage: 12 VDC; Lamp: 3 watt LEDTotal lumen output: 80

Certifications andCompliances:NEC/CEC:

• Class I, Division 2, Groups B, C, D, Zone 2

UL Standards:

• 1598A (Supplemental Requirements forLuminaires for Installation on MarineVessels)

• 924 (Emergency Lighting and PowerEquipment)

• 844 (Electric Luminaires HazardousLocations)

CSA Standards:

• C22.2 No. 141-M1985 unit equipmentfor emergency lighting

• C22.2 No. 137-M1981 non-incendiveelectrical equipment for use in Class I,Division 2 hazardous locations

• Life Safety Code NFPA101® – Section 5-9 (Emergency Lighting)

• Marine wet locations suitability, Type 4X

Unit Net Weights:• N2LPS12222 – 16 lbs.• N2LPS12220 – 12 lbs.• N2RF1221 – 8 lbs.• N2RF1222 – 9 lbs.

10L

Note: Battery time in emergency mode is 90 minutes.


10L

Cl. I, Div. 2, Groups B, C, DCl. I, Zone 2Wet Locations, MarineNEMA 3, 3R, 4XAmbient 0ºC to 55ºC

Note: Up to four (4) remote LED lamp assemblies can be connected to the N2LPS12222. Up to six (6) remote LED lamp assemblies can beconnected to the N2LPS12220.

Wire Sizing for Remote Installation:For Copper Wire –Running Distance† (ft.) Between Power Supply and Remote Luminaire

Load In Watts Load In Watts

Wire Size 8 16 24 32 Wire Size 8 16 24 32

16 AWG 26 13 6 3 10 AWG 106 53 26 1314 AWG 42 21 10 5 8 AWG 168 84 42 2112 AWG 66 33 16 8 6 AWG 270 135 67 33†Maximum distance to limit line voltage drop to 5%.

Dimensions (N2LPS):

16.0

13.5

18.0

7.5

14.513.8

5.0

1.1

7.4

Standard – N2LPS LED Light-Pak™


Emergency Lighting System10L

Ordering Information:Description Cat. #

28 watt, 12 volt power supply assembly with two 3 watt LED lamp heads N2LPS1222228 watt, 12 volt stainless steel power supply assembly with two 3 watt LED lamp heads N2LPS12222 SS28 watt, 12 volt power supply assembly less luminaire heads N2LPS12220*Remote luminaire assembly with one 3 watt LED lamp head N2RF1221*Remote luminaire assembly with two 3 watt LED lamp heads N2RF1222*28 watt, 120V LED Light-Pak with single sided exit sign** N2LPS12222/120 EXS DR039173428 watt, 277V LED Light-Pak with single sided exit sign** N2LPS12222/277 EXS DR039173428 watt, 120V LED Light-Pak with double sided exit sign** N2LPS12222/120 EXD DR039173428 watt, 277V LED Light-Pak with double sided exit sign** N2LPS12222/277 EXD DR0391734

*Not cUL approved. UL Listed only.**Exit sign operates in both normal and emergency mode.

1152-1153.qxp 5/30/2011 11:15 AM Page 1153


10L

10L

Dimensions (N2LPS):

EXS, EXD Option – N2LPS LED Light-Pak™ with Optional Emergency Exit Luminaire

Dimensions (N2RF):

11.77

3.83

9.50

7.27

3.83

9.50

4.38

Detail Indication Logic:

Status Indication Status Description Status Definition

No Light AC Power Removed from Circuit* Steady Light (No Blinks) Fully Charged*-* Light Blinks Once Battery Charging**-** Light Blinks Twice Battery Failure***-*** Light Blinks Three Times Circuit Failure


Emergency Lighting SystemCl. I, Div. 2, Groups B, C, DCl. I, Zone 2Wet Locations, MarineNEMA 3, 3R, 4XAmbient 0ºC to 55ºC

1154-1155.qxp 5/30/2011 11:16 AM Page 1154

10L NEMA 4X, IP66 CCH UX Series LED Exit Signs … y...1162 US: 1-866-764-5454 CAN: 1-800-265-0502...

Documents

Transcript of 10L NEMA 4X, IP66 CCH UX Series LED Exit Signs … y...1162 US: 1-866-764-5454 CAN: 1-800-265-0502...