10416 Polyurethane 750ml AW - Woodcare Direct Tough Clear_Varnish2.pdf · provides long lasting...
3
Ronseal Ultra Tough Varnish Flammable. Repeated exposure may cause skin dryness or cracking. Keep out of the reach of children. Keep away from sources of ignition – No smoking. Avoid contact with skin and eyes. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. After contact with skin, wash immediately with plenty of water. Wear suitable gloves. If swallowed, seek medical advice immediately and show this container or label. Use only in well-ventilated areas. Dispose of this material and its container to a hazardous or special waste collection point. Contains Cobalt 2-Ethylhexanoate, ETHYL METHYL KETOXIME. May produce an allergic reaction. EU limit value for this product (cat. A/e): 500g/l (2007) / 400g/l (2010). This product contains max 500g/l VOC Ronseal Ultra Tough Hardglaze Ronseal Ultra Tough Hardglaze is a superior polyurethane gloss varnish which protects interior wood whilst adding depth to the beauty of the wood grain. The polyurethane - alkyd formulation provides long lasting protection against knocks and scratches and resists most household chemical spillages including boiling water and alcohol. The high content of polyurethane in the varnish ensures quicker hardness and abrasion build up than other solvent based varnishes. The extended working time eliminates lap marks to deliver a rich, clear, mellow finish that enhances the beauty of the wood. Preparation Ensure all surfaces are free from wax, grease and oil by wiping with a cloth dampened with white spirit. Barewood: Sand smooth with fine sandpaper. Remove dust with a cloth dampened with white spirit. Varnished wood: Remove unsound varnish. Sand well to a uniform appearance and clean with white spirit. Allow to dry thoroughly. Avoid inhaling dust when sanding by wearing a suitable face mask. Application Stir well before and during use. Apply in a warm, well-ventilated room. Using a brush, apply 2 or 3 coats. Brush out evenly and finish each coat in the direction of the grain. Leave 4 hours between coats. Before final coat, lightly rub down using fine sandpaper and wipe with white spirit. Clean Up Clean brushes with white spirit or paint brush cleaner. Remove as much varnish as possible from the brush before cleaning. Some local authorities have special facilities for disposing of waste coatings. Do not empty into drains or watercourses. Important Do not use on plastic type materials. Certain tropical woods may prolong drying times or cause poor adhesion. Always test on a small area first. Polyurethane varnishes may darken the colour of bare wood & dyed wood. Special precautions should be taken during surface preparations of pre-1960s paint surfaces over wood and metal as they contain harmful lead. Drying times may be extended when using over Colron Wood Dye. To avoid risk of spillage, always store and transport in a secure and upright position. For a water clear finish use Ronseal Quick Drying Clear Varnish. For use only as directed. FOR FURTHER ADVICE, PLEASE CONTACT: RONSEAL TECHNICAL SERVICES, Tel: 0114 240 9469 Ronseal Ltd, Thorncliffe Park, Chapeltown, Sheffield, S35 2YP. Telephone: 0114 246 7171 Fax: 0114 246 5629 Email: [email protected] www.ronseal.co.uk 750ml Made in Great Britain. Ronseal & Ronseal Does Exactly What It Says On The Tin are registered trademarks of the Sherwin- Williams Company. © Ronseal 2007 5 010214 566938 Usage Areas Any bare or previously treated interior wood including doors, furniture, shelving, skirting boards, cork, hardboard or chipboard. Compatability Suitable for use on bare wood or over existing solvent based finishes such as varnish or wood dye. Finish Rich, gloss sheen. Number of coats 2 for treated wood, 3 for untreated wood. Coverage Up to 10 square metres per litre. 750ml will be sufficient to treat 4 door sides with 2 coats (approx 7.5 sq m). Dry Times Touch dry in 2 hours. Recoat in 4 hours. Clean Up Clean brushes with white spirit or paint brush cleaner.
-
Upload
truongdung -
Category
Documents
-
view
215 -
download
0
Transcript of 10416 Polyurethane 750ml AW - Woodcare Direct Tough Clear_Varnish2.pdf · provides long lasting...
10416_Polyurethane_750ml_AW 19/4/12 10:48 Page 1
Ronseal Ultra Tough VarnishFlammable. Repeated exposure may cause skin drynessor cracking. Keep out of the reach of children. Keepaway from sources of ignition – No smoking. Avoidcontact with skin and eyes. In case of contact witheyes, rinse immediately with plenty of water andseek medical advice. After contact with skin, washimmediately with plenty of water. Wear suitable gloves.If swallowed, seek medical advice immediately andshow this container or label. Use only in well-ventilatedareas. Dispose of this material and its container to ahazardous or special waste collection point. ContainsCobalt 2-Ethylhexanoate, ETHYL METHYL KETOXIME.May produce an allergic reaction.
ULTRA TOUGH
TOUGH POLYURETHANE GLOSS VARNISHFOR INTERIOR WOOD
HARDGLAZEHARDGLAZEEU limit value for this product (cat. A/e): 500g/l (2007) / 400g/l (2010).This product contains max 500g/l VOC
Ronseal Ultra Tough HardglazeRonseal Ultra Tough Hardglaze is a superiorpolyurethane gloss varnish which protects interiorwood whilst adding depth to the beauty of thewood grain. The polyurethane - alkyd formulationprovides long lasting protection against knocksand scratches and resists most householdchemical spillages including boiling water andalcohol. The high content of polyurethane in thevarnish ensures quicker hardness and abrasionbuild up than other solvent based varnishes. Theextended working time eliminates lap marks todeliver a rich, clear, mellow finish that enhancesthe beauty of the wood.
PreparationEnsure all surfaces are free from wax, greaseand oil by wiping with a cloth dampened withwhite spirit. Barewood: Sand smooth with finesandpaper. Remove dust with a cloth dampenedwith white spirit. Varnished wood: Removeunsound varnish. Sand well to a uniformappearance and clean with white spirit. Allowto dry thoroughly. Avoid inhaling dust whensanding by wearing a suitable face mask.
ApplicationStir well before and during use. Apply in a warm,well-ventilated room. Using a brush, apply 2 or 3coats. Brush out evenly and finish each coat inthe direction of the grain. Leave 4 hours betweencoats. Before final coat, lightly rub down usingfine sandpaper and wipe with white spirit.
Clean UpClean brushes with white spirit or paint brushcleaner. Remove as much varnish as possiblefrom the brush before cleaning. Some localauthorities have special facilities for disposingof waste coatings. Do not empty into drainsor watercourses.
ImportantDo not use on plastic type materials. Certaintropical woods may prolong drying timesor cause poor adhesion. Always teston a small area first. Polyurethanevarnishes may darken the colourof bare wood & dyed wood.Special precautions shouldbe taken during surfacepreparations of pre-1960s paintsurfaces over wood and metalas they contain harmful lead.Drying times may be extendedwhen using over Colron WoodDye. To avoid risk of spillage,always store and transport in asecure and upright position. For a waterclear finish use Ronseal Quick DryingClear Varnish. For use only as directed.
FOR FURTHER ADVICE, PLEASE CONTACT:RONSEAL TECHNICAL SERVICES, Tel: 0114 240 9469
Ronseal Ltd, Thorncliffe Park, Chapeltown, Sheffield, S35 2YP.Telephone: 0114 246 7171 Fax: 0114 246 5629
Email: [email protected] www.ronseal.co.uk750mlMade in Great Britain. Ronseal & Ronseal Does Exactly WhatIt Says On The Tin are registered trademarks of the Sherwin-Williams Company. © Ronseal 2007
501
0214
5669
38
Usage Areas Any bare or previously treated interior wood including doors, furniture, shelving, skirting boards, cork, hardboard or chipboard.
Compatability Suitable for use on bare wood or over existing solvent based finishes such as varnish or wood dye.
Finish Rich, gloss sheen.Number of coats 2 for treated wood, 3 for untreated wood.Coverage Up to 10 square metres per litre. 750ml will
be sufficient to treat 4 door sides with 2 coats(approx 7.5 sq m).
Dry Times Touch dry in 2 hours. Recoat in 4 hours.Clean Up Clean brushes with white spirit or paint brush cleaner.
10416_Polyurethane_750ml_AW 19/4/12 10:48 Page 2
Ronseal Ultra Tough VarnishFlammable. Repeated exposure may cause skin drynessor cracking. Keep out of the reach of children. Keepaway from sources of ignition – No smoking. Avoidcontact with skin and eyes. In case of contact witheyes, rinse immediately with plenty of water andseek medical advice. After contact with skin, washimmediately with plenty of water. Wear suitable gloves.If swallowed, seek medical advice immediately andshow this container or label. Use only in well-ventilatedareas. Dispose of this material and its container to ahazardous or special waste collection point. ContainsCobalt 2-Ethylhexanoate, ETHYL METHYL KETOXIME.May produce an allergic reaction.
ULTRA TOUGH
TOUGH POLYURETHANE MATT VARNISHFOR INTERIOR WOOD
MATTCOATMATTCOATEU limit value for this product (cat. A/e): 500g/l (2007) / 400g/l (2010).This product contains max 500g/l VOC
Ronseal Ultra Tough MattcoatRonseal Ultra Tough Mattcoat is a superiorpolyurethane matt varnish which protects interiorwood whilst adding depth to the beauty of thewood grain. The polyurethane - alkyd formulationprovides long lasting protection against knocksand scratches and resists most householdchemical spillages including boiling water andalcohol. The high content of polyurethane in thevarnish ensures quicker hardness and abrasionbuild up than other solvent based varnishes. Theextended working time eliminates lap marks todeliver a rich, clear, mellow finish that enhancesthe beauty of the wood.
PreparationEnsure all surfaces are free from wax, greaseand oil by wiping with a cloth dampened withwhite spirit. Barewood: Sand smooth with finesandpaper. Remove dust with a cloth dampenedwith white spirit. Varnished wood: Removeunsound varnish. Sand well to a uniformappearance and clean with white spirit. Allowto dry thoroughly. Avoid inhaling dust whensanding by wearing a suitable face mask.
ApplicationStir well before and during use. Apply in a warm,well-ventilated room. Using a brush, apply 2 or 3coats. Brush out evenly and finish each coat inthe direction of the grain. Leave 4 hours betweencoats. Before final coat, lightly rub down usingfine sandpaper and wipe with white spirit.
Clean UpClean brushes with white spirit or paint brushcleaner. Remove as much varnish as possiblefrom the brush before cleaning. Some localauthorities have special facilities for disposingof waste coatings. Do not empty into drainsor watercourses.
ImportantDo not use on plastic type materials. Certaintropical woods may prolong drying timesor cause poor adhesion. Always teston a small area first. Polyurethanevarnishes may darken the colourof bare wood & dyed wood.Special precautions shouldbe taken during surfacepreparations of pre-1960s paintsurfaces over wood and metalas they contain harmful lead.Drying times may be extendedwhen using over Colron WoodDye. To avoid risk of spillage,always store and transport in asecure and upright position. For a waterclear finish use Ronseal Quick DryingClear Varnish. For use only as directed.
FOR FURTHER ADVICE, PLEASE CONTACT:RONSEAL TECHNICAL SERVICES, Tel: 0114 240 9469
Ronseal Ltd, Thorncliffe Park, Chapeltown, Sheffield, S35 2YP.Telephone: 0114 246 7171 Fax: 0114 246 5629
Email: [email protected] www.ronseal.co.uk750mlMade in Great Britain. Ronseal & Ronseal Does Exactly WhatIt Says On The Tin are registered trademarks of the Sherwin-Williams Company. © Ronseal 2007
501
0214
5669
52
Usage Areas Any bare or previously treated interior wood including doors, furniture, shelving, skirting boards, cork, hardboard or chipboard.
Compatability Suitable for use on bare wood or over existing solvent based finishes such as varnish or wood dye.
Finish Rich, matt sheen.Number of coats 2 for treated wood, 3 for untreated wood.Coverage Up to 10 square metres per litre. 750ml will
be sufficient to treat 4 door sides with 2 coats(approx 7.5 sq m).
Dry Times Touch dry in 2 hours. Recoat in 4 hours.Clean Up Clean brushes with white spirit or paint brush cleaner.
10416_Polyurethane_750ml_AW 19/4/12 10:48 Page 3
ULTRA TOUGH
TOUGH POLYURETHANE SATIN VARNISHFOR INTERIOR WOOD
SATINCOATSATINCOATRonseal Ultra Tough VarnishFlammable. Repeated exposure may cause skin drynessor cracking. Keep out of the reach of children. Keepaway from sources of ignition – No smoking. Avoidcontact with skin and eyes. In case of contact witheyes, rinse immediately with plenty of water andseek medical advice. After contact with skin, washimmediately with plenty of water. Wear suitable gloves.If swallowed, seek medical advice immediately andshow this container or label. Use only in well-ventilatedareas. Dispose of this material and its container to ahazardous or special waste collection point. ContainsCobalt 2-Ethylhexanoate, ETHYL METHYL KETOXIME.May produce an allergic reaction.
EU limit value for this product (cat. A/e): 500g/l (2007) / 400g/l (2010).This product contains max 500g/l VOC
Ronseal Ultra Tough SatincoatRonseal Ultra Tough Satincoat is a superiorpolyurethane satin varnish which protects interiorwood whilst adding depth to the beauty of thewood grain. The polyurethane - alkyd formulationprovides long lasting protection against knocksand scratches and resists most householdchemical spillages including boiling water andalcohol. The high content of polyurethane in thevarnish ensures quicker hardness and abrasionbuild up than other solvent based varnishes. Theextended working time eliminates lap marks todeliver a rich, clear, mellow finish that enhancesthe beauty of the wood.
PreparationEnsure all surfaces are free from wax, greaseand oil by wiping with a cloth dampened withwhite spirit. Barewood: Sand smooth with finesandpaper. Remove dust with a cloth dampenedwith white spirit. Varnished wood: Removeunsound varnish. Sand well to a uniformappearance and clean with white spirit. Allowto dry thoroughly. Avoid inhaling dust whensanding by wearing a suitable face mask.
ApplicationStir well before and during use. Apply in a warm,well-ventilated room. Using a brush, apply 2 or 3coats. Brush out evenly and finish each coat inthe direction of the grain. Leave 4 hours betweencoats. Before final coat, lightly rub down usingfine sandpaper and wipe with white spirit.
Clean UpClean brushes with white spirit or paint brushcleaner. Remove as much varnish as possiblefrom the brush before cleaning. Some localauthorities have special facilities for disposingof waste coatings. Do not empty into drainsor watercourses.
ImportantDo not use on plastic type materials. Certaintropical woods may prolong drying timesor cause poor adhesion. Always teston a small area first. Polyurethanevarnishes may darken the colourof bare wood & dyed wood.Special precautions shouldbe taken during surfacepreparations of pre-1960s paintsurfaces over wood and metalas they contain harmful lead.Drying times may be extendedwhen using over Colron WoodDye. To avoid risk of spillage,always store and transport in asecure and upright position. For a waterclear finish use Ronseal Quick DryingClear Varnish. For use only as directed.
FOR FURTHER ADVICE, PLEASE CONTACT:RONSEAL TECHNICAL SERVICES, Tel: 0114 240 9469
Ronseal Ltd, Thorncliffe Park, Chapeltown, Sheffield, S35 2YP.Telephone: 0114 246 7171 Fax: 0114 246 5629
Email: [email protected] www.ronseal.co.uk750mlMade in Great Britain. Ronseal & Ronseal Does Exactly WhatIt Says On The Tin are registered trademarks of the Sherwin-Williams Company. © Ronseal 2007
501
0214
5669
45
Usage Areas Any bare or previously treated interior wood including doors, furniture, shelving, skirting boards, cork, hardboard or chipboard.
Compatability Suitable for use on bare wood or over existing solvent based finishes such as varnish or wood dye.
Finish Rich, satin sheen.Number of coats 2 for treated wood, 3 for untreated wood.Coverage Up to 10 square metres per litre. 750ml will
be sufficient to treat 4 door sides with 2 coats(approx 7.5 sq m).
Dry Times Touch dry in 2 hours. Recoat in 4 hours.Clean Up Clean brushes with white spirit or paint brush cleaner.
