10.01.03.160
-
Upload
md-saifur-rahman -
Category
Technology
-
view
177 -
download
0
Transcript of 10.01.03.160
![Page 1: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/1.jpg)
Presentation on
uniaxial column design
Presented by
Md. Saifur Rahman Sayeef
Student ID: 10.01.03.160
Department of Civil Engineering
AUST, Dhaka
![Page 2: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/2.jpg)
UNIAXIAL COLUMN DESIGN
![Page 3: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/3.jpg)
WHAT IS UNIAXIAL COLUMN?
• Uniaxial columns are those whose rotation are strictly bound about a single axis only as the load eccentricity is pure about a single axis.
![Page 4: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/4.jpg)
Bending moments can occur in columns because:
• - Unbalance gravity loads
• - Lateral loads: wind, earthquake
• - In general a certain degree of eccentricity is present due to inaccuracies in construction.
![Page 5: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/5.jpg)
The column types depending on applied load.
![Page 6: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/6.jpg)
Column types
![Page 7: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/7.jpg)
Column types based on dimensional property
SHORT – both lex/h and ley/b < 15 for braced columns
< 10 for unbraced columns
BRACED - If lateral stability to structure as a whole is
provided by walls or bracing designed to resist all lateral
forces in that plane, else unbraced.
![Page 8: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/8.jpg)
UNIAXIAL SHORT COLUMN DESIGN BY INTERACTION CURCVE (USD) METHOD
![Page 9: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/9.jpg)
Column subjected to eccentric compression
![Page 10: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/10.jpg)
![Page 11: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/11.jpg)
Balanced Failure, eb
![Page 12: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/12.jpg)
![Page 13: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/13.jpg)
![Page 14: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/14.jpg)
Moment Strength of Column
![Page 15: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/15.jpg)
![Page 16: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/16.jpg)
![Page 17: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/17.jpg)
![Page 18: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/18.jpg)
![Page 19: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/19.jpg)
![Page 20: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/20.jpg)
![Page 21: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/21.jpg)
![Page 22: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/22.jpg)
![Page 23: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/23.jpg)
![Page 24: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/24.jpg)
![Page 25: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/25.jpg)
![Page 26: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/26.jpg)
![Page 27: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/27.jpg)
UNIAXIAL SHORT COLUMN DESIGN BY (WSD) METHOD
![Page 28: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/28.jpg)
1. If column controlled by compression eccentricity, e= M/P <= eb :-
• For symmetrical tied column, eb=
(0.67Pgm+0.17)d
• For spiral column, eb=
(0.43PgmDs+0.14t)
• Pg= As/Ag
• m= fy/0.85f’c
![Page 29: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/29.jpg)
Selection of column is done using the relation –
(fa/Fa) + (fb/Fb) <=1, (this is also known as interaction formula.)
Where,fa= P/Ag
Fa= 0.34(1+Pgm)fc’fb= M/SS= I/c (c=0.5h)Fb= 0.45 fc’
![Page 30: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/30.jpg)
2. If column controlled by tension, e>eb
Section of column shall be proportioned by using the relation-
M= Mo+ P/Pb (Mb-Mo)Pb & Mb shall be calculated by using the relation-(fa/Fa) + (fb/Fb)= 1=> (Pb/Ag)/Fa + (Pbeb/S)/Fb= 1
For symmetrical tied column, Mo= 0.4 As fy (d-d’), As is tensile steel.
For spiral column, Mo= 0.12 Ast fy Ds, Ast is total steel.
![Page 31: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/31.jpg)
SLENDER COLUMN DESIGN
![Page 32: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/32.jpg)
Slender columns are also becoming increasingly important and popular because of the following reasons:
(i) the development of high strength materials (concrete and steel),
(ii) improved methods of dimensioning and designing with rational and reliable design
procedures,
(iii) innovative structural concepts – specially, the architect’s expectations for creative structures.
![Page 33: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/33.jpg)
HYSTERESIS?
• slender or long columns may fail at a much lower value of the load compared to short column when sudden lateral displacement of the member takes place between the ends. Thus, short columns undergo material failure, while long columns may fail by buckling (geometric failure) at a critical load or Euler’s load, which is much less in comparison to that of short columns having equal area of cross-section.
• The general expression of the critical load Pcr at which a member will fail by buckling is as follows:
• Pcr = π2EI /(kl)2 or,
• Pcr = π2EA /(kl/r)2
• Thus, Pcr of a particular column depends upon kl/r or slenderness ratio. It is worth mentioning that kl is termed as effective length le of the column.
![Page 34: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/34.jpg)
![Page 35: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/35.jpg)
![Page 36: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/36.jpg)
![Page 37: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/37.jpg)
Critical loads in terms of Pcr of hinge-hinge column and effective lengths le = klof elastic and reinforced concrete columns with different boundary conditions
and for a constant unsupported length l
Sl.
No.
Support conditions Critical load
Pcr
Effective length
le = kl
(A) Elastic single columns 1. Hinged at both ends, no
sidesway
Pcr l
2. Fixed against rotation at
both ends – no sidesway
4Pcr 0.5 l
3. Partially restrained against
rotation by top and bottom
cross-beams, no sidesway
Between Pcr and 4Pcr l > kl > l/2
4. Fixed at one end and
entirely free at other end –
sidesway not prevented
0.25 Pcr 2 l, one PI is on imaginary
extension
5. Rotationally fixed at both
ends – sidesway not
prevented
Pcr l, one PI is on imaginary
extension
6. Partially restrained against
rotation at both ends –
sidesway not prevented
Between zero and slightly
less than Pcr *
l < kl < α
(B) Reinforced concrete columns 7. Hinged portal frame – no
sidesway
> Pcr kl < l
8. Hinged portal frame –
sidesway not prevented
<< Pcr kl > 2 l
![Page 38: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/38.jpg)
Additional Moment Method of analysis of short column
1.Braced columns bent symmetrically in single curvature and undergoing balanced failure
M = Mo + Py
=>Mo + P ea = Mo + Ma
• Where,
• P is the factored design load
• M are the total factored design moments
• Mo are the primary factored moments
• Ma are the additional moments
• ea are the additional eccentricities
![Page 39: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/39.jpg)
DEFLECTION DIAGRAMS
![Page 40: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/40.jpg)
ΦMAX= 10Δ/le2
Hence,
ea=Δ = Φ le2/10
![Page 41: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/41.jpg)
Assuming the column undergoes a balanced failure when Pu= Pub, the maximum curvature at the mid-height section of the column can be expressed as given below, assuming
(i) the values of εc = 0.0035, εst = 0.002 and d’/D = 0.1, and (ii) the additional moment capacities are about eighty per cent
of the total moment. Then,
φ = eighty per cent of {(0.0035 + 0.002)/0.9D}or φ = 1/200D Substituting the value of φ , we haveea = D(le/D)2/2000
![Page 42: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/42.jpg)
• Therefore, the additional moment Ma can be written as,
• Ma = Py = PΔ = Pea = (PD/2000) (le/D)2
![Page 43: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/43.jpg)
2.Braced columns subjected to unequal primary moments at the two ends
• Mo max = 0.4 M1 + 0.6 M2
• Mo max ≥ 0.4 M2
Where,
• M1 is smaller end moment.
• M2 is larger end moment.
![Page 44: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/44.jpg)
3. Unbraced columns
• Mo max = M2 + Ma
![Page 45: 10.01.03.160](https://reader036.fdocuments.us/reader036/viewer/2022062710/55a23dea1a28ab1f6e8b466a/html5/thumbnails/45.jpg)