1. What’s in the box 2a Overview 2b Overview 3. Wall mount ... · 4. Mark on the wall using each...
Transcript of 1. What’s in the box 2a Overview 2b Overview 3. Wall mount ... · 4. Mark on the wall using each...
www.tclusa.com/support or www.tclcanada.com/support
1-877-300-9223
TCL SUPPORT:
Sound Bar main unit TCL Alto 5
AC power cord
Optical cable
3.5mm-to-3.5mmaudio cable
IR pass-through cable
Remote control (with battery)
QSG Wall mount template
Warranty
Usermanual
OPTICAL USB
AC~
Wall bracket screws
AUX IR
Press to turn the Sound Bar on or to standby mode.
Press to mute or unmute the sound.
Press to switch the audio source among different modes.
Press to increase or decrease the volume level.
Press to skip to previous/next track in Bluetooth/USB mode.
Play/pause/resume playback in Bluetooth/USB mode. Press and hold to activate the pairing function in Bluetooth mode or disconnect the paired Bluetooth device.
NEWS/MOVIE/MUSICPress to select the equalizer (EQ) effect when you are watching news or movies or listening to music.
Press to turn the Sound Bar main unit on or to standby mode.
Press to switch the audio source among AUX/Bluetooth/Optical/USB modes.
Press to select the Bluetooth function.
Press to increase or decrease the volume level.
LED
1 2
43
Sound Bar status LED indicators
in standby mode The red LED is on solidly.
in AUX mode The green LED is on solidly.
in Bluetooth mode The blue LED is on solidly.
ready to pair The blue LED flashes slowly.
pairing in progress The blue LED flashes quickly.
in optical mode The orange LED is on solidly.
in USB mode The white LED is on solidly.
Operation LED indicators
Listen to music. The white LED is on.
Press to pause the music. The white LED is on solidly.
Press or to skip to the previous/next track The white LED is on solidly.
USB
Not supplied
LED
1
2
1. Press .
2. Press . The blue LED flashes slowly. The Sound Bar is ready to pair.
3. Power on your Bluetooth device and activate its Bluetooth function.
4. Select TCL Alto 5. You hear distinct double beep sounds. The blue LED remains on solidly when pairing is successful.
1 2
3
Removethe screws
Install the wallmounting screws
Fig.1 Fig.3
Fig.4
Fig.2
Wall template
Silicone pad
WE AREREADY TOHELP contact us first
with any questions
DO NOT RETURN TO STORE
TAKE CARE WHENREMOVING THE SOUNDBAR
Operation LED indicators
The white LED flashes quickly and goes back to the source LED.
The red LED keeps flashing.
The red LED flashes and goes back to the source LED.
The white LED flashes once.
The green LED flashes once.
The orange LED flashes once.
Optical input connector
USB Type A connector (only for
music playback)
AUX input connector
IR pass-through cable connector
(IR pass-through cable connector)
AC inputpower connector
TCL Alto 5
1. Place the supplied wall mount template on the wall. Make sure the wall mount template is at least 2 inches (5cm) below the center of the TV.2. Use a level to make sure the Sound Bar is positioned accurately.3. Use the tape to stick the wall mount template firmly on the wall. 4. Mark on the wall using each marking on the template through the mounting holes (Fig.1).5. Take away the wall mount template.6. Drill a screw hole at each marking on the wall (Fig.1).7. Insert the supplied wall anchors into 4 screw holes on the wall (Fig. 2).8. Insert the supplied wall bracket screws into the wall anchors. Leave 4mm between the screw heads and the wall (Fig. 2).9. Fix and tighten the wall bracket screws on the wall. Stick the silicone pads on the wall mount brackets when necessary to adjust the direction of the Sound Bar main unit (Fig. 2).10. Replace the screws at the back of the Sound Bar main unit with the supplied wall mounting screws (Fig. 3 and 4).11. Hang the Sound Bar main unit on the screws.
Wall anchor x 4Silicone pad x 2
Wall mount bracket x 2Wall bracket screw (M4) x 4
Wall mounting screw (M3) x 2
Copyright © 2019 TCL. All rights reserved. TS5000_US_EN_QSG_V2.0
2.0 Channel Home Theater Sound BarAlto 5
Quick start guide
1. What’s in the box 2a Overview 2b Overview 3. Wall mount
4a Activate the remote control
4b Replace the remote control battery
Sound Bar main unit Remote control
5a. Connect 7a. Use 7c. Use5b. Connect 6. Pairing
Bluetooth device LED behaviors under different source mode
7b. Use
Use the USB device for music playbackIR pass-through cable1. 3.5mm-to-3.5mm audio cable2. RCA-to-3.5mm (not supplied)3. Optical cable
Power supply
Remote sound functions
7
35
911
Battery type: Lithium CR2025 battery (160 mAh) x 1
735 mm / 28.94”