1-s2.0-S0016236110003698-main
-
Upload
winkarsyah -
Category
Documents
-
view
212 -
download
0
Transcript of 1-s2.0-S0016236110003698-main
7/26/2019 1-s2.0-S0016236110003698-main
http://slidepdf.com/reader/full/1-s20-s0016236110003698-main 1/7
Atomization and combustion of canola methyl ester biofuel spray
Jaime A. Erazo Jr., Ramkumar Parthasarathy *, Subramanyam Gollahalli
Combustion and Flame Dynamics Laboratory, School of Aerospace and Mechanical Engineering, 865 Asp Ave Room 212, University of Oklahoma, Norman, OK 73019, USA
a r t i c l e i n f o
Article history:
Received 14 July 2009
Received in revised form 10 June 2010Accepted 15 July 2010
Available online 25 July 2010
Keywords:
Biofuel
Combustion
Spray
Emission
Drops
a b s t r a c t
The spray atomization and combustion characteristics of canola methyl ester (CME) biofuel are compared
to those of petroleum based No. 2 diesel fuel in this paper. The spray flame was contained in an optically
accessible combustor which was operated at atmospheric pressure with a co-flow of heated air. Fuel wasdelivered through a swirl-type air-blast atomizer with an injector orifice diameter of 300lm. A two-com-
ponent phase Doppler particle analyzer was used to measure the spray droplet size, axial velocity, and
radial velocity distributions. Radial and axial distributions of NO, CO, CO2 and O2 concentrations were also
obtained. Axial and radial distributions of flame temperature were recorded with a Pt–Pt/13%Rh (type R)
thermocouple. The volumetric flow rates of fuel, atomization air and co-flow air were kept constant for
both fuels. The droplet Sauter mean diameter (SMD) at the nozzle exit for CME biofuel spray was smaller
than that of the No. 2 diesel fuel spray, implying faster vaporization rates for the former. The flame tem-
perature decreased more rapidly for the CME biofuel spray flame than for the No. 2 diesel fuel spray flame
in both axial and radial directions. CME biofuel spray flames produced lower in-flame NO and CO peak
concentrations than No. 2 diesel fuel spray flames.
2010 Elsevier Ltd. All rights reserved.
1. Introduction
Because of the uncertain petroleum prices and the impetus to
develop renewable energy sources, biofuels are emerging as alter-
natives to petroleum fuels with practical applicability to diesel en-
gines, gas turbines, and industrial continuous combustors.
Biodiesel fuel has many important advantages over conventional
petroleum based fuels. Biodiesel is renewable, carbon-neutral from
an environment standpoint, and is sulfur-free. However, one draw-
back in the use of biodiesel fuels seems to be the increase in NO by
1–14% that has been reported from biodiesel fuelled compression–
ignition engines [1–3]. A variety of reasons have been cited for this
increase in NO emissions. Increasing iodine number has been cor-
related with increasing NO emissions from biodiesel fuelled en-
gines [1,4]. Another recent study attributed the increased NO
emissions to the increased presence of double bonds in biodieselfuels [4]. It has also been suggested that the bulk modulus differ-
ence between biodiesel and No. 2 diesel fuel causes an advance
in the fuel injection when using biodiesel [4–6], resulting in higher
temperatures and higher NO. However, the results of experiments
with continuous combustion systems such as gas turbine combus-
tors and oil furnaces show the opposite effect: NO x seems to be
lowered when certain biofuels are substituted for petroleum fuels,
either in the pure form or as blends [7–9].
The laser imaging studies by Dec [10] have revealed that the
mechanisms and processes in the combustion of a fuel spray in a
diesel engine significantly differ from the earlier model proposed
by Faeth [11] that was also applicable to continuous spray combus-
tors. Therefore, the NO emission increases observed in biodiesel
fuelled engines may not occur in continuous combustors such as
gas turbines. To understand this discrepancy, studies on flame
structure of sprays, in a more controlled environment than the
complex thermo-chemical environment existing in engines are
needed; this idea formed the basis of the present study.
In this paper, combustion characteristics of canola methyl ester
(CME) biodiesel were documented in a continuous combustor set-
up. In a companion project, biodiesel combustion in a laminar
flame was studied to isolate fuel chemistry effects [12], the results
of which provide baseline data for comparison. The specific goal of
this paper was to investigate the differences in the combustion andemission characteristics between No. 2 diesel and CME spray
flames. Parameters, such as air-preheat temperature, atomization
air, and global equivalence ratio, were controlled to provide direct
comparison. In-flame temperature, in-flame concentrations of NO,
CO, CO2 and O2, and spray droplet size and mean droplet axial/ra-
dial velocities were measured.
2. Experimental apparatus
The experiments were conducted in a large, steel combustion
chamber, shown in Fig. 1. A preheated, air co-flow system was used
0016-2361/$ - see front matter 2010 Elsevier Ltd. All rights reserved.doi:10.1016/j.fuel.2010.07.022
* Corresponding author.
E-mail addresses: [email protected] (J.A. Erazo Jr.), [email protected]
(R. Parthasarathy), [email protected] (S. Gollahalli).
Fuel 89 (2010) 3735–3741
Contents lists available at ScienceDirect
Fuel
j o u r n a l h o m e p a g e : w w w . e l s e v i e r . c o m / l o c a t e / f u e l
7/26/2019 1-s2.0-S0016236110003698-main
http://slidepdf.com/reader/full/1-s20-s0016236110003698-main 2/7
to deliver combustion air obtained from the lab supply line. Heat-
ing was accomplished using a 10 kW electrical resistance heater in
conjunction with a temperature controller. A settling chamber wasused to provide a uniform flow of air surrounding the spray. The
flame was contained in a stainless steel test unit with Vycor glass
windows for optical accessibility.
The fuel tank was pressurized with nitrogen, while the atomiza-
tion air was supplied from an air cylinder. An air-blast atomizer
with an injector diameter of 300lm was used to produce the
spray. A schematic diagram of the air/fuel tubing is presented in
Fig. 2.
The spray droplet size and velocity distributions were measured
using a 2-channel phase Doppler particle analyzer (PDPA) [13,14].
The source of light was an argon-ion laser operated at 225 mW,
which was split into the green (514 nm) and blue (488 nm) light.
Bragg cells were used to frequency shift one beam of each color
to facilitate the measurement of reversed flows. The receiving op-tics was set-up in the off-axis (30) forward-scatter mode. The
diameter-measurement system was calibrated with a mono-dis-
perse droplet generator. In general, approximately 10,000 data
points were collected at each measurement location in the spray
flame and averaged. At certain locations in the spray flame, such
as at the edges and far downstream of the injector, it was not pos-
sible to collect such a high number of data points within a reason-
able amount of time. On an average, approximately 120 s were
needed to collect the data points at a given location. The PDPA
transmitting and receiving optics were mounted on three-way tra-
verses to move the measuring volume to different locations in the
spray flame. The flame was almost symmetric about the vertical
axis, therefore, only half-width profiles are presented.
Species concentration profiles of CO, CO2, NO, and O2 were mea-sured using a portable gas analyzer. CO and CO2 concentrations
were measured using a non-disperse infrared detector (NDIR)
based on the attenuation of the infrared wavelength beam specific
to the species [15], while NO x and O2 concentrations were mea-sured using electro-chemical detectors [16]. The samples were col-
lected using a 1 mm diameter orifice, uncooled quartz probe. An
inline filter and a condenser were used to filter the moisture and
particles before passing the flue gases through the analyzers. The
probe was mounted on a two-way traverse. Access into the flame
was accomplished by using two custom cut Vycor glass pieces
which provided a narrow slot through which the probe was in-
serted. A thin ceramic gasket material was used to cover the excess
slot area. The flame temperature was measured using a silica-
coated type R thermocouple (Pt/Pt–Rh 13%), with a 0.35 mm bead
diameter. Data acquisition was accomplished using LabView soft-
ware and a personal computer. All thermocouple data were cor-
rected for radiation and convection errors. Radial profiles of
temperature and species concentration profiles were recorded ataxial locations at 25%, 50%, and 75% of the visible flame length from
the burner exit; the flame length was recorded by a digital camera
with a long-time exposure (1 s) in background lighting.
The properties of the fuels are provided in Table 1. Test condi-
tions including the fuel and atomization air flow rates are pre-
sented in Table 2. A global equivalence ratio of nominal value
0.68 was used to simulate lean burning combustors. All test condi-
tions were held constant with the exception of the air-preheat
temperature. CME has a higher initial boiling point than No. 2 die-
sel fuel (Table 1). Preheating the fuel would aid the atomization
and evaporation processes; however, overheating could result in
the fuel coking and clogging the atomizer tip. Therefore, the fuel
was not preheated. The heat release and pollutant emissions are
dependent on the vaporization and modes of combustion of thedrops in the spray. In order to minimize the influence of the differ-
1 2
3 4
5
67 8
9
10
1 – Air Filter and
Rotameter
2 – Co Flow Air Heater
3 – Fuel Rotameter4 – Air Rotameter
5 – Settling Chamber
6 – Flame Chamber
7 – Fuel Tank
8 – Nitrogen Tank
9 – Steel Chamber
10 – Exhaust Vent
Not to Scale
Fig. 1. Schematic drawing of combustion chamber.
1
2
3
4
5
67
8
1 – Fuel Inlet2 – Air Inlet
3 – Settling Chamber
with Marbles4 – Screen
5 – Air Co- Flow Inlet6 – Flame Chamber
7 – Injector8 – Set Screw
Not to Scale
20.3 cm
51.8 cm
Fig. 2. Schematic drawing of air and fuel tubing.
3736 J.A. Erazo Jr. et al./ Fuel 89 (2010) 3735–3741
7/26/2019 1-s2.0-S0016236110003698-main
http://slidepdf.com/reader/full/1-s20-s0016236110003698-main 3/7
ence in boiling points on the combustion characteristics, the
co-flow air temperature was adjusted to be a constant fraction
(two-thirds) of the initial boiling point in both spray flames. The
uncertainties in the measurements were computed following stan-
dard procedures and are shown as uncertainty bars in the figures
displaying measurements. More details of the set-up and proce-
dure are presented by Erazo [17].
3. Results and discussion
The spray droplet Sauter mean diameter (SMD) profiles for No.
2 diesel fuel and CME fuel are presented in Fig. 3. The refractive
index of the drops changes due to the heat transfer in the flame;
the change in refractive index was estimated to be 6.8% [18]. The
maximum estimated error in the SMD measurement due to the
change in refractive index was 5% for the 30-lm drops and 8%
for the 60-lm drops [19]. The drop diameter calibration curve
slope was set at the initial refractive index value, as suggested by
Schneider and Hirleman [19]. In general, the droplet size increased
with increasing radial distance from the injector at all axial loca-
tions. Due to the swirl imparted by the injector, the large dropswere thrown to the spray edge, and took longer to evaporate and
burn, resulting in an increase in SMD in the outer edge of the spray,
similar to observations made in other investigations [20–22]. The
drop sizes in both spray flames are comparable in the near-injector
region. Farther downstream of the injector, the drop sizes were
comparable for both sprays. At an axial distance of 3 cm from the
injector, the SMD of CME was larger than that of the diesel spray
flame; this could be due to the smaller drops of CME evaporating
faster than the diesel drops [23], leaving the larger drops to remain
at this axial location.
The axial and radial components of velocity of the No. 2 diesel
and CME fuel droplets at varying axial locations in the spray flame
are presented in Figs. 4 and 5 respectively. Similar trends are ob-
served in both fuel sprays. The mean droplet axial velocity peaked
at the centerline and decreased with increasing radial distance
from the injector. The mean axial component of droplet velocity
decreased with increasing axial distance from the injector as thespray width increased. This behavior is similar to the gas velocity
profile in a jet. The mean axial velocity of the CME drops was high-
er than that of the diesel drops near the spray edge due to the
smaller SMD at these locations. The axial momentum injected
was constant for both fuels; the smaller SMD drops have less slip,
and therefore higher velocity near the edge.
The mean radial component of droplet velocity, on the other
hand, increased with increasing radial distance from the injector
axis. The swirl effect coupled with the preferential combustion of
smaller droplets depleted the number of smaller droplets at the
spray edges leaving only larger droplets with more momentum.
The radial velocity of the CME spray drops was smaller than the ra-
dial velocity of the diesel spray drops because of their smaller size
in the near-injector region.A comparison of the in-flame temperature profiles (Fig. 6) of the
two spray flames indicates that in the near-injector region (25%
flame height) the flame temperatures were similar, but in the
far-injector region the CME spray flame had lower temperatures.
In some places, the CME in-flame temperature was lower by as
much as 200 K than in the No. 2 diesel spray flame.
The in-flame concentration profiles of CO, CO2, O2 and NO at dif-
ferent axial locations (25%, 50%, and 75% of visible flame height)
are presented in Figs. 7 and 8. The NO concentration measure-
ments are plotted together with the in-flame temperatures to eval-
Table 1
Physical and chemical properties of No. 2 diesel fuel and canola methyl ester fuel.
Fuel Molecular formula Density (kg/m3) Boiling point (C) Viscosity ( cSt) H eating value ( MJ /k g) Iodine numb er
No. 2 diesel fuel C16H34 850 150–350 2.63 at 40 C 42.6 8.6
Canola methyl ester C19H36O2 881 340–405 4.37 at 40 C 37.4 115
Table 2
Fuel and air flow rates and temperature settings.
Atomization air flow rate (l/min) Co-flow air flow rate (l/min) Co-flow air temperature (C) Fuel flow rate (ml/min)
No. 2 diesel fuel 6.32 58 100 4.6
Canola methyl ester 6.32 58 232 4.6
Radial Position (cm)
S a u t e r M e a n D i a m e t e r ( m i c r o n
)
0 0.5 1 1.5 20
20
40
60
80
0.5 cm
1 cm2 cm
3 cm
CME FuelVf = 4.6 ml/min
Vaa = 6.32 l/minVcf = 58 l/minTcf = 232 C
Axial Distances Downstream of Nozzle
Radial Position (cm)
S a u t e r M e a n D i a m e t e r ( m i c r o n
)
0 0.5 1 1.5 20
20
40
60
80
0.5 cm
1 cm2 cm
3 cm
3.5 cm
No. 2 Diesel FuelVf = 4.6 ml/min
Vaa = 6.32 l/minVcf = 58 l/minTcf = 100 C
Axial Distances Downstream of Nozzle
Fig. 3. Sauter mean diameter profiles for No. 2 diesel fuel and CME fuel spray flames.
J.A. Erazo Jr. et al. / Fuel 89 (2010) 3735–3741 3737
7/26/2019 1-s2.0-S0016236110003698-main
http://slidepdf.com/reader/full/1-s20-s0016236110003698-main 4/7
uate the significance of NO production by the Zeldovich mecha-
nism, which is closely correlated with flame temperature. In the
diesel spray flame, the concentrations of CO, CO2 and NO peaked
at 0.75 cm in the radial direction, while the O2 concentration
was at a minimum at this location. The in-flame temperature pro-
file also correlated well with the in-flame concentration profiles of NO, with profiles having peaks at this same location. This behavior
indicates that NO formation in these flames is strongly driven by
the Zeldovich mechanism. The in-flame concentration trends im-
ply that the reaction front of the spray flame at this flame height
is at approximately 0.75 cm from the flame axis in the radial direc-
tion. This behavior was observed at all the flame heights.
The CME in-flame concentration profiles displayed trends dif-ferent from those observed in the diesel spray flame. A clear-cut
Radial Position (cm)
M e a n D r o p l e t A
x i a l V e l o c i t y ( m / s )
0 0.25 0.5 0.75 1 1.25 1.5 1 .75 20
3
6
9
12
15
18
0.5 cm
1 cm
2 cm3 cm
3.5 cm
Axial Distances Downstream of NozzleNo. 2 Diesel FuelVf = 4.6 ml/minVaa = 6.32 l/minVcf = 58 l/minTcf = 100 C
Radial Position (cm)
M e a n D r o p l e t A
x i a l V e l o c i t y ( m / s )
0 0.25 0.5 0 .75 1 1.25 1 .5 1 .75 20
3
6
9
12
15
18
0.5 cm1 cm
2 cm
3 cm
Axial Distances Downstream of NozzleCME FuelVf = 4.6 ml/minVaa = 6.32 l/minVcf = 58 l/minTcf = 232 C
Fig. 4. Mean droplet axial velocity profiles for No. 2 diesel fuel and CME fuel spray flames.
Radial Position (cm)
M e a n D r o p l e t R a d i a l V e l o c i t y ( m / s )
0 0.25 0 .5 0 .75 1 1.25 1 .5 1 .75 2-3
-2
-1
0
1
2
3
4
5
0.5 cm
1 cm
2 cm
3 cm3.5 cm
No. 2 Diesel FuelVf = 4.6 ml/minVaa = 6.32 l/minVcf = 58 l/minTcf = 100 C
Axial Distances Downstream of Nozzle
Radial Position (cm)
M e a n D r o p l e t R a d i a l V e l o c i t y ( m / s )
0 0.25 0 .5 0 .75 1 1.25 1 .5 1 .75 2-3
-2
-1
0
1
2
3
4
5
0.5 cm1 cm
2 cm
3 cm
Axial Distances Downstream of NozzleCME FuelVf = 4.6 ml/minVaa = 6.32 l/minVcf = 58 l/minTcf = 232 C
Fig. 5. Mean radial droplet velocity profiles for No. 2 diesel fuel and CME fuel spray flames.
Radial Position (cm)
F l a m e T e m p e r a t u r e ( K )
0 0.5 1 1.5 21200
1400
1600
1800
2000
2200
25% Flame Length
50% Flame Length
75% Flame Length
Axial Distances Downstream of Nozzle
No. 2 Diesel Fuel
Vf = 4.6 ml/minVaa = 6.32 l/minVcf = 58 l/minTcf = 100 C
Radial Position (cm)
F l a m e T e m p e r a t u r e ( K )
0 0.5 1 1.5 21200
1400
1600
1800
2000
2200
25% Flame Length
50% Flame Length
75% Flame Length
Axial Distances Downstream of Nozzle
CME Fuel
Vf = 4.6 ml/minVaa = 6.32 l/minVcf = 58 l/minTcf = 232 C
Fig. 6. In-flame temperature profiles for No.2 diesel fuel and CME fuel spray flames.
3738 J.A. Erazo Jr. et al./ Fuel 89 (2010) 3735–3741
7/26/2019 1-s2.0-S0016236110003698-main
http://slidepdf.com/reader/full/1-s20-s0016236110003698-main 5/7
reaction front was not observed in the CME spray flame. At 25%
flame height, the CO concentration peaked at approximately
1.25 cm in the radial direction. The O2 concentration reached a
minimum at the centerline and increased in the radial direction,whereas the CO2 concentration peaked at the centerline and de-
creased in the radial direction. The NO and in-flame temperature
profiles did not display any correlation. At all flame heights, the
CME spray flame produced less NO than the No. 2 diesel fuel spray
flame. This behavior was seen at other flame heights, but in a less
pronounced fashion.
From these measurements, distinctly different combustion pro-
cesses can be discerned in the two spray flames. The No. 2 diesel
fuel burned in a heterogeneous combustion environment, where
fuel droplets of varying size were evaporating and burning. Soot
formation and oxidation was evident from the luminous, yellow
flame produced. This combustion mode resulted in an increase
in-flame temperature and NO formation, as seen in the in-flame
measurements. In contrast, increased droplet evaporation, lessluminosity, and reduced in-flame temperatures in the CME spray
flame are all indicative of significant homogenous gas phase reac-
tions. The difference is due to the fuel-bound oxygen present in the
ester functional group of the CME fuel molecule, which aids the
oxidation process and suppresses soot precursors [24].The lower NO concentrations in the CME spray flame are oppo-
site to the observations of increased NO emissions in biodiesel
fuelled, intermittent combustion, compression–ignition engines
reported in various studies [1–3]; however, recent spray flame
studies under continuous combustion conditions similar to those
simulated in this paper, have reported decreases in NO x emissions
[7–9] in agreement with our work.
This disagreement between the compression–ignition engine
and other spray flame studies, at a first glance, may be attributed
to the large differences in variability of pressure, temperature,
and residence time between compression–ignition engines and
continuous combustors. According to the long-accepted Faeth’s
model [11] for spray combustion, both spray flames (intermittent
or continuous) exhibit similar behavior; therefore, it was initiallydifficult to rationalize these observations. Besides, we were sur-
Fig. 7. In-flame concentration profiles of CO, CO2, O2 and NO of No. 2 diesel fuel spray flame.
J.A. Erazo Jr. et al. / Fuel 89 (2010) 3735–3741 3739
7/26/2019 1-s2.0-S0016236110003698-main
http://slidepdf.com/reader/full/1-s20-s0016236110003698-main 6/7
prised to see that NO x emissions were higher for biofuels than for
the diesel fuel when their vapors were burned in gas-flame burners
[12], in agreement with the observations made in CI engines. A
much closer examination of the more recent, laser-diagnostics
based combustion model of Dec [10], reveals that most of the fuel
injected into a compression–ignition engine burns in the homoge-
neous gas-flame mode, and hence accounts for the congruence of
observations between the gas burners and CI engines, and variance
from those in continuous spray combustors.
4. Summary and conclusions
Spray flames of No. 2 diesel fuel and CME fuel were studied un-
der conditions simulating continuous combustors. Droplet size,
velocity, in-flame temperature, and in-flame species concentration
profiles were obtained for the two flames. The CME spray flame
displayed higher rates of droplet evaporation compared to the
No. 2 diesel spray. The No. 2 diesel fuel spray produced larger drop-
lets. The smaller drops in the CME spray flame had higher mean ax-
ial velocities and lower radial velocities in the far-injector region.
The CME spray flame produced less NO at all flame heights com-pared to the No. 2 diesel flame. Also, the CME spray flame was
up to 200 K cooler than the No. 2 diesel spray flame in the far-bur-
ner region. Overall, the No. 2 diesel spray flame operated mostly in
the heterogeneous combustion mode, in contrast to more homog-
enous, gas phase combustion demonstrated by the CME fuel spray
flame. The CME spray flame behavior was in agreement with other
biodiesel spray flame studies under similar continuous combustion
conditions. Also, the variation between CI engine and continues
spray combustion in the NO x production of biofuels compared to
petroleum fuel can be explained by the differences of the dominant
combustion mode.
Acknowledgments
This work was supported by a grant from the Oklahoma Bioen-
ergy Center. The first author would also like to thank the US
Department of Education for funding received through a GAANN
fellowship.
References
[1] McCormick RL, Graboski MS, Alleman TL, Herring AM. Impact of source
material and chemical structure on emissions of criteria pollutants from aheavy-duty engine. Environ Sci Technol 2001;35:1742–7.
Fig. 8. In-flame concentration profiles of CO, CO2, O2 and NO of CME fuel spray flame.
3740 J.A. Erazo Jr. et al./ Fuel 89 (2010) 3735–3741
7/26/2019 1-s2.0-S0016236110003698-main
http://slidepdf.com/reader/full/1-s20-s0016236110003698-main 7/7
[2] Lin Y, Wu YG, Chang CT. Combustion characteristics of waste-oil producedbiodiesel/diesel fuel blends. Fuel 2007;86:1772–80.
[3] Tat ME, Van Gerpen JH. Fuel property effects on biodiesel. ASAE annualinternational meeting, paper no. 036034; 2003.
[4] Ban-Weiss G, Chen JY, Buchholz BA, Dibble RW. A numerical investigation intothe anomalous slight NO x increase when burning biodiesel: a new (old) theory.Am Chem Soc, Fuel Chem Div 2006;51(1):24–30.
[5] Szybist JP, Boehman AL, Taylor JD, McCormick RL. Evaluation of formulationstrategies to eliminate the biodiesel NO x effect. Fuel Process Technol2005;86:1109–26.
[6] Mueller CJ, Boehman AL, Martin GC. An experimental investigation of theorigin of increased NO x emissions when fueling a heavy-duty compression–ignition engine with soy biodiesel. SAE paper no. 2009-01-1792; 2009.
[7] Li L. Experimental study of biodiesel spray and combustion characteristics. SAEpower train and fluid systems conference and exhibit, paper 2006-01-3250;October 2006.
[8] Hashimoto N, Ozawa Y, Mori N, Yuri I, Hamamatsu T. Fundamental combustioncharacteristics of palm methyl ester as alternative fuel for gas turbines. Fuel2008;87:3373–8.
[9] Habib Z, Parthasarathy RN, Gollahalli SR. Effects of biodiesel on theperformance and emission characteristics of a small-scale gas turbine. 47thAIAA aerospace sciences meeting and exhibit, AIAA 2009-0827, Orlando; 2009.
[10] Dec JE. A conceptual model of DI diesel engine combustion based on lasersheet imaging. SAE paper no. 910224; 1997.
[11] Faeth GM. Current status of droplet and liquid combustion. Prog EnergyCombust Sci 1977;3:191–224.
[12] Love N, Parthasarathy RN, Gollahalli SR. Rapid characterization of radiationand pollutant emissions of biodiesel and hydrocarbon liquid fuels. J Energy ResTechnol 2009;131:012202-1–2-8.
[13] Bachalo WD, Houser MJ. Phase/doppler spray analyzer for simultaneousmeasurements of drop size and velocity distributions. Opt Eng1984;23:583–90.
[14] Sankar SV, Bachalo WD. Response characteristics of the phase Doppler particleanalyzer for sizing spherical particles larger than the light wavelength. ApplOpt 1991;30:1487–96.
[15] Yi SH, Park YW, Han SO, Min N, Kim ES, Ahn TW. Novel NDIR CO 2 sensor forindoor air quality monitoring. In: 13th International conference on solid-statesensors, actuators and microsystems, Seoul, South Korea; 2005.
[16] Nova Analytical Systems Inc. Instruction manual for NOVA model 7466Kportable engine exhaust analyzer. New York: Nova Analytical Systems Inc.
[17] Erazo Jr JA. Effects of droplet size and fuel iodine number on biodiesel sprayflames. MS thesis. Norman, Oklahoma: School of Aerospace and Mechanical
Engineering, University of Oklahoma.[18] Lipkin MR, Kurtz SS. Temperature coefficient of density and refractive index
for hydrocarbons in the liquid state. Ind Eng Chem 1941;13:291–5.[19] Schneider M, Hirleman ED. Influence of internal refractive index gradients on
size measurements of spherically symmetric particles by phase Doppleranemometry. Appl Opt 1994;33:2379–87.
[20] Gupta AK, Presser C, Hodges JT, Avedisian CT. Role of combustion on droplettransport in pressure-atomized spray flames. J Propul Power 1996;12:543–53.
[21] Marchine T, Allouis C, Amoresano A, Beretta F. Experimental investigation of apressure swirl atomizer spray. J Propul Power 2007;23:1096–101.
[22] Lee SG. Geometrical effects on spray characteristics of air-pressurized swirlflows. J Mech Sci Technol 2008;22:1633–9.
[23] Morin C, Chauveau C, Dagaut P, Gokalp I, Cathonnet M. Vaporization andoxidation of liquid fuel droplets at high temperature and high pressure:application to n-alkanes and vegetable oil methyl esters. Combust Sci Technol2004;176:499–529.
[24] Kitamura T, Ito T, Senda J, Fujimoto H. Detailed chemical kinetic modeling of diesel spray combustion with oxygenated fuels. Society of automotiveengineers, SAE 2001 World congress, paper no. 2001-01-1262.
J.A. Erazo Jr. et al. / Fuel 89 (2010) 3735–3741 3741