1 Introduction Line attribute Color and gray scale Area filled attribute Anti-aliasing.
-
Upload
brandon-tate -
Category
Documents
-
view
218 -
download
1
Transcript of 1 Introduction Line attribute Color and gray scale Area filled attribute Anti-aliasing.
1
Introduction
• Line attribute
• Color and gray scale
• Area filled attribute
• Anti-aliasing
2
Attributes of Output Primitives
DefinitionDefinitionParameter that affects the way a primitive will be Parameter that affects the way a primitive will be displayeddisplayed
Line Attribute
. Type
. Width
. Color
. Pen & Brush
3
Line Attribute
Type
. Solid
. Dotted – very short dash with spacing equal to
or greater than dash itself
. Dashed – displayed by generating an interdash spacing
Pixel count for the span and interspan length is specified
by the mask . Ex. 111100011110001111
Note : Fixed pixel with dashes can produce unequal length dashes. It depend on line orientation. So, need to adjust the number of plotted pixels for different slopes.
4
Line Attribute
Width
. Specify in pixels and proportion of a standard line width.
. Thicker line can be produced by.
. Adding extra pixel vertically when |m| < 1
. Adding extra pixel horizontally when |m| > 1
. Issues:
. Line have different thickness on the slope
. Problem with
. End of the line
. Joining the two lines (polygon)
5
Attributes of Output Primitives
6
Attributes of Output Primitives
7
Line Attribute
Pen and Brush. The selected “pen” or “brush” determine the way a line will be drawn.
. Pens and brushes have size, shape, color and pattern attribute.
. Pixel mask is applied in both of them.
8
Curve Attribute
Similar to line : type + width
Thicker curves can be produced by:
1. Plotting additional pixel
2. Filling the space between two concentric circles.
3. Using thicker pen or brush
9
COLOR AND GRAY SCALE LEVEL
ColorColors are represented by colors codes which are
positive integers.
Color information is stored in frame buffer or in separate table and use pixel values as index to the color table.
Two ways to store color information :1. Direct 2. Indirect
10
COLOR
Direct
11
COLOR
Indirect
12
COLOR
Exercise:
What is the size of frame buffer required for the following cases:
Case 1 (Direct): Resolution of 1024 * 1024 with 24 bits per pixel
Case 2 (Indirect): Same resolution with 8 bit per pixel that indexed out of 16 million available colors
Conclusion
CLUT is good for storage but can’t give a very high resolution picture.
13
GRAY SCALE LEVEL
Apply for monitor that have no color
Shades of grey (white->light grey->dark grey->black) Color code mapped onto grayscale codes 2 bits can give 4 level of grayscale 8 bits per pixel will allow 256 combination Dividing the actual code with 256 will give range of 0 and 1
Ex:Color code in color display is 118
To map to nearest grayscale then
118/256 = 0.45
light gray
Scale Shade
1 black
0.66 Dark grey
0.33 Light Grey
0 White
14
AREA FILLED ATTRIBUTE
. Option for filling a defined region is whether solid , pattern and colors.
Fill Styles . Three basic fill styles are:
. hollow with color border.. interior color is same with background
15
AREA FILLED ATTRIBUTE
. filled with a solid color .. color up to and including the border
pattern .. control by other table
16
Pattern Fill
Ex: Table with two dimensional array of color codes.Index 1: Cpa[1,1] = 4
Cpa[2,2] = 4 | 4 0 | Cpa[1,2] = 0 | 0 4 | Cpa[2,1] = 0
Index 2: Cpb[1,1] = 4 Cpb[2,2] = 4 | 4 6 4 |
Cpb[3,3] = 4 | 6 4 6 | Cpb[1,2] = 6 | 4 6 4 |
Cpb[2,1] = 6 Cpb[2,3] = 6 Cpb[1,3] = 4 Cpb[3,1] = 4 Cpb[3,3] = 4
17
Pattern Fill
.Filling an area with rectangular pattern is called tiling.
.Some pattern are generated based on and, or, xor, replace logic which result based on the foreground and background color.
.Soft Fill is a method where factor is given in order to control the transparency of background and foreground
P = tF+(1-t)B t: transparency value 0-1
18
ANTIALIASING
19
ANTIALIASING
20
ANTIALIASING
This distortion is due to low-frequency sampling and it is called aliasing.
.To improve the appearance is called antialiasing method.
.The straight line, circle and ellipse drawing algorithms have to decide which pixel are closest to line.
.Scan conversion samples a line and choose which of the much smaller number of pixel on the screen to be plotted to represent a line.
21
ANTIALIASING
Increasing Screen Resolution
22
ANTIALIASING
Supersampling
23
ANTIALIASING
24
ANTIALIASING
25
ANTIALIASING
26
ANTIALIASING
27
ANTIALIASING
28
ANTIALIASING
29
ANTIALIASING
30
Conclusion
• Polygon Filling (scan-line, boundary, flood) • Line attributes (size, type, color,pen&brush)• Color and gray scale representation and storing
• Full 24-bit• Color LUT
• Area filled (polygon) attributes • Fill styles (hollow, filled, pattern)
• Distortion (aliasing)• Anti-aliasing techniques
• Screen resolution• Super sampling• Area sampling (Weighted & unweighted)