1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 - Danfoss A3 IP20 ABC.pdf · mcad-a3-ip20-abc 001 drawing...
1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 A B C D E F G H J K L M B C D E F G H J K L M A THIS DRAWING SHOWS THE MOST COMMON VERSION OF THIS PRODUCT VARIANT. SMALL DIFFERENCES MAY OCCUR DEPENDING ON THE FINAL PRODUCT CONFIGURATION. CENTER OF GRAVITY: FOR REFERENCE ONLY, THE PRODUCT CONFIGURATION MAY INFLUENCE THE CG IN ALL THREE AXES. 1 OF 1 MCAD-A3-IP20-ABC PROPERTY OF DANFOSS A/S NORDBORG, DENMARK. TWO OR THREE DIMENSIONAL REPRODUCTION OF CONTENTS TO BE AUTHORIZED BY DANFOSS A/S. SHEET MODEL 001 MCAD-A3-IP20-ABC REV DRAWING NUMBER MCAD A3 IP20 ABC CHECKED 30-12-2015 DANFOSS DESIGNED CHANGED DESCRIPTION FINISH A1 1:2 UNLESS OTHERWISE SPECIFIED THE TOLERANCE IS # 1MM [0.4 INCH]. ALL DIMENSIONS ARE IN MILLIMETERS [INCH] MATERIAL DRAWING SIZE SCALE FIRST ANGLE PROJECTION Type Value Max Weight 6.6 kg / 14.6 Ib IP Class IP20 ABC Nema Class CHASSIS MIN 100 [3.9] MIN 100 [3.9] 170 [6.69] 268 [10.55] 130 [5.12] 110 [4.33] 8 [0.31] 257 [10.12] 6.5 [0.26] 5.5 [0.22] 4.5 [0.18] 5.5 [0.22] 11 [0.43] 219 [8.62] 374 [14.72] AIR INLET AIR OUTLET SEE DETAIL A SEE DETAIL B MOUNTING BASE LABEL AREA DETAIL A SCALE 1:1 DETAIL B SCALE 1:1
Transcript of 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 - Danfoss A3 IP20 ABC.pdf · mcad-a3-ip20-abc 001 drawing...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A
B
C
D
E
F
G
H
J
K
L
M
B
C
D
E
F
G
H
J
K
L
M
A
THIS DRAWING SHOWS THE MOST COMMON VERSION OF THIS PRODUCT VARIANT. SMALL DIFFERENCES MAY OCCUR DEPENDING ON THE FINAL PRODUCT CONFIGURATION. CENTER OF GRAVITY: FOR REFERENCE ONLY, THE PRODUCT CONFIGURATION MAY INFLUENCE THE CG IN ALL THREE AXES. 1 OF 1MCAD-A3-IP20-ABC
PROPERTY OF DANFOSS A/S NORDBORG, DENMARK. TWO OR THREE DIMENSIONAL REPRODUCTION OF CONTENTS TO BE AUTHORIZED BY DANFOSS A/S. SHEETMODEL
001MCAD-A3-IP20-ABCREVDRAWING NUMBER
MCAD A3 IP20 ABC
CHECKED
30-12-2015 DANFOSSDESIGNED
CHANGED
DESCRIPTION
FINISHA11:2
UNLESS OTHERWISE SPECIFIED THE TOLERANCE IS �#�1MM [0.4 INCH].
ALL DIMENSIONS ARE IN MILLIMETERS [INCH]
MATERIALDRAWINGSIZE
SCALEFIRST ANGLE PROJECTION
Type Value
Max Weight 6.6 kg / 14.6 Ib
IP Class IP20 ABC
Nema Class CHASSIS
MIN
100
[3.9
] M
IN 1
00[3
.9]
170[6.69]
268
[10.
55]
130[5.12]
110[4.33]
8[0
.31]
257
[10.
12]
6.5
[0.2
6]
5.5[0.22]
4.5
[0.1
8]
5.5[0.22]
11[0.43]
219[8.62]
374
[14.
72]
AIR
INLE
T
AIR
OU
TLET
SEE DETAIL A
SEE DETAIL B
MOUNTING BASE
LABE
L A
REA
DETAIL ASCALE 1:1
DETAIL BSCALE 1:1
