Nexans Euromold MV Separable Connectors & Bushings - Interface A
0.8 HDR - htk-jp.com · HDR series Interface Connectors Outline HDR series connectors are very...
Transcript of 0.8 HDR - htk-jp.com · HDR series Interface Connectors Outline HDR series connectors are very...
HDR seriesInterface Connectors
OutlineHDR series connectors are very small surface mount (SMT) interfaceconnectors with their contacts arranged at a pitch of 0.8 mm, designed forthe purpose of saving extra space on printed circuit boards.
Features
PrincipalApplications
ElectricalCharacteristics
• Long-life design allowing up to 5,000 mating cycles• Low profile with overall height of 5mm from the PCB surface• Sequential structure allowing up to two stacked connections• One-touch-lock-type and detachable / re-attachable housing
• IDC type connector on the cable end allows simultaneous termination
Portable information terminals, smaller-sized office automation equipment,and their peripherals
Rated voltage 125V AC (r.m.s.)
Rated current 0.5 A
Insulation resistance Over 1000 megohms at 250V DC
Dielectric withstanding voltage 350V AC (r.m.s.)
Contact resistance 70 milliohms or less
• EMI/ESD-shielded and over-molded type metal housing
Document Disclaimer
When placing orders with us, minimum order quantities are set for every product.
Be sure to contact us before starting preliminary design of PCBs using our connectors.
The specifications and information shown in the catalog are subject to change without notice.
mm Pitch0.8
Connectors
Reflow temperature profile(for reference purposes)
Flow temperature profile(for reference purposes)
The reflow temperature profile shown in this drawing is for reference purposes. This profile depends on requirements such as reflow equipment, soldering paste, and PCB size. Thus, this profile may not meet with your specific situation. Please evaluate your PCB-mounting soldering and set your own reflow temperature profile.
ΩApplicable products
The profile shown in this drawing is applicable only for those products shown above.
The flow temperature profile as shown above is for reference purposes. This profile depends on requirements such as the PCB size. Thus, this profile may not meet with your specific situation. Please evaluate your PCB-mounting soldering and set your own flow temperature profile.
ΩApplicable products
The profile shown in this drawing is applicable only for those products shown above.
HDR-EA( )LMYPG1-( )( )+HDR-EA( )LFYPG1-( )( )+
HDR-EC( )FDT( )-( )+HDR-EC( )LFDT( )-( )+
100~130˚C
260±5˚C
30~60sec
5sec
150~180˚C
220˚C
250˚C
(Full heating period)
30~60sec
(Preheating period)90~120sec
(Peak)
Product List
IDC type male connector forcableHDR-E( )MAG1+
A-6HDRHDR series...4
Soldering type male connector forcableHDR-E( )MSG1+
A-7HDRHDR series...5
Straddle SMT type maleconnector for PCBHDR-E50MT( )+
A-8HDRHDR series...6
Right-angle SMT type maleconnector for PCBHDR-EA( )LMYPG1-( )( )+
A-9HDRHDR series...7
IDC type female connector forcableHDR-E( )FAG1+
A-10HDRHDR series...8
Right-angle SMT type femaleconnector for PCBHDR-EA( )LFYPG1-( )( )+
A-11HDRHDR series...9
Straight through hole type femaleconnector for PCBHDR-EC( )FDT( )-( )+
A-12HDRHDR series...10
Right-angle through hole typefemale connector for PCBHDR-EC( )LFDT( )-( )+
A-13HDRHDR series...11
EMI-filtered vertical plastichousing for standard and thincableHDR-E( )LP( )( )-( )A-14HDRHDR series...12
EMI-filtered screw-lock verticaltype plastic housingHDR-E26LPH
A-15HDRHDR series...13
0.8mm pitch connector
For cable
IDC
EMI shielded
IDC type male connector for cableHDR- E( )MAG1+
Mating connector: HDR series SMT type or through hole type female connector
For use with housings: HDR series upright housing
Required tools: Termination tool: FHAT-0029, IDC tool: FHPT-923B, Hand presser: MFC-K1 (Refer to page Tool-10)
10.8
15.6
25.2
0.8≈6=4.8
0.8≈12=9.6
0.8≈24=19.2
9.0
13.8
23.4
● Dimensions
HDR-E14MAG1+
HDR-E26MAG1+
HDR-E50MAG1+
Part No. A B C
● Components
➀ Contacts
➁ Shell
➂ Insulator
➃ Spacer
➄ Cable housing
5026
2614
148
B
A
C15˚
LAST POS.
POS.#1
14.9
6.7
B
B ➄
➃
➁
14 contacts
➂
➀
14 contacts
26 contacts
● Configuration of product Part No.
HDR- E ( ) M A G1+➀ ➁ ➂ ➃ ➄ ➅
➀ Series name➁ E: With metal shell➂ No. of contacts: 14, 26 or 50➃ Type of contact
M: IDC type, Male
➄ Compatible cableA: AWG#30 (7/0.1), dia. 0.58mm
➅ Contact platingG1: 0.76μm or more Gold plate
5.4
3.7
0.8
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
0.8mm pitch connector
For cable
Soldering
EMI shielded
Soldering type male connector for cableHDR-E( )MSG1+
Mating connector: HDR series female connector
For use with housings: HDR-E( )LPH
● Configuration of product Part No.
HDR- E ( ) M S G1+➀ ➁ ➂ ➃ ➄ ➅
➀ Series name➁ E: With metal shell➂ No. of contacts: 26 or 50
➄ Soldering➅ Contact plating
G1: 0.76μm or more Gold plate
➃ Male
15.6
25.2
13.8
23.4
0.8≈12=9.6
0.8≈24=19.2
HDR-E26MSG1+
HDR-E50MSG1+
APart No. B C
● Dimensions
A
B
C
C
26-contact connector
C
POS.#1
POS.#10.8
POS.#n/2
POS.#n/2
POS.#nPOS.#n/2+1
POS.#n/2+1 POS.#n
16
.2±
0.5
6.7
±0
.15
5.4
±0
.3
15˚
0.8
0.8
13
2614
1
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
0.8 mm pitch connector
For PCB
Straddle SMTStraddle SMT type male connector for PCBHDR-E50MT( )+
Mating connector: HDR series SMT type female connector
● Configuration of product Part No.
HDR- E 50 MT ( )+➀ ➁ ➂ ➃
➀ Series name➁ No. of contacts: 50➂
PCB thickness➃
Type of contactMT: Straddle SMT type, male
Blank: 0.4 mmA : 0.8 mm
● Components➀ Contacts
➁ Insulator
➂ Shell
0.45±0.03
0.45±0.03
0.8±0.05
3.5±
0.0
5
5.5±
0.1
5.5±
0.1
3.5
±0.0
5
0.8±0.05
22.6≠0.05
0.8≈24=19.2±0.1
0.8≈24=19.2±0.1
0.8≈24=19.2
Prohibited area for mounting parts
0.8POS.#1
POS.#1 POS.#25
POS.#50POS.#26
POS.#50POS.#26
POS.#25
POS.#25 POS.#50 POS.#26POS.#1
14.9
6.7
1 25
23.4
25.2
0.8≈24=19.2
0.8
5.4
26 50
–0.1
2-C0.
2
2-C
0.1
Recommended PCB layout
➀
➁
➂
15˚
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
0.8mm pitch connector
For PCB
Right-angle SMTRight-angle SMT type male connector for PCBHDR-EA( )LMYPG1- ( )( )+
● Configuration of product Part No.
HDR- EA ( ) ( ) ( )+LMY P G1-➀ ➁ ➂ ➃ ➄ ➅ ➆
➀ Series name➁ Contact pitch: 0.635 mm➂ No. of contacts: 14 or 26➃ Type of contact
LMY: Right-angle SMT type, male➄ Contact plating
G1: 0.76 μm or more Gold plate
➅ Lock screwBlank : NoneSL : Provided
➆ Length of lock screwE: 6.6 (standard)
Compatible with B-to-B and B-to-CK: 3.3 (for HDR-E ( ) LPA-LS)
Mating connector: HDR series IDC type or solder type female cable connector
For use with housing: -SLE: HDR series vertical housing
-SLK: HDR series vertical housing -LS, -LSA
CBA
D15˚
5
➂
➀➃
➇➁
POS.#1 POS.#n/2
POS.#n/2≠1 POS.#n
0.8
3
6.617
.41.
6
10.7
RE
F.6.
7
➅
E
0.635 0.2~0.25FB
POS.#1
POS.#n/2≠1
POS.#n
POS.#n/2
ø1.7ø1.1
2.5
0.8
1.7
5
POS.#n
POS.#n/2+1 POS.#n/2POS.#1
Recommended PCB layout
20.0
24.8
14.4
19.2
4.8
9.6
9.2
14
8.255
15.875
19.0
23.8
● Dimensions
HDR-EA14LMYPG1-( )( )+
HDR-EA26LMYPG1-( )( )+
Part No. A B C9
13.8
D E F G
● Components➀ Insulator A
➁ Shell
➂ Contacts
➃ Insulator B
➄ Square nuts
➅ Hold down
➆ Hex nuts
➇ Lock screw
: PAD
3.7
E±0.1
B±0.1
G±0.13±0.15 3±0.15
6±
0.1
5
2.5±
0.1
7.2
±0.1
F±0.05
0.335±0.03
2-ø1.8±0.1
2-ø2.3±0.05
0.635±0.03
➄➆
4≠
0–
0.1
5
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
0.8mm pitch connector
For cable
IDC
EMI shielded
IDC type female connector for cableHDR-E( )FAG1+
Mating connector: HDR series SMT type male connector
For use with housings: HDR series vertical housing
Required tools: Termination tool: FHAT-0029, IDC tool: FHPT-923B, Hand presser: MFC-K1 (Refer to page Tool-10)
10.8
15.6
4.8
9.6
8.8
13.6
● Dimensions
HDR-E14FAG1+
HDR-E26FAG1+
Part No. A B C
● Components➀ Contacts
➁ Insulator
➂ Shell
➃ Spacer
➄ Cable housing
● Configuration of product Part No.
HDR- E ( )F A G1+➀ ➁ ➂ ➃ ➄ ➅
➀ Series name➁ E: With metal shell➂ No. of contacts: 14 or 26➃ Type of contact
F: IDC type, female
➄ Compatible cableA: AWG#30 (7/0.1), dia. 0.58 mm
➅ Contact platingG1: 0.76 μm or more Gold plate
0.8POS.#n/2 POS.#1
POS.#n POS.#n/2+1
B
A
5.4
C15˚
14 8
➄
➃
➀
3.5
14.2
6
➂
➁
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
0.8mm pitch connector
For PCB
Right-angle SMTRight-angle SMT type female connector for PCBHDR-EA( )LFYPG1-( )( )+
Mating connector: HDR series IDC or solder type male cable connector
● Components➀ Insulator A
➁ Shell
➂ Contacts
➃ Insulator B
➄ Square nuts
➅ Hold down
➆ Hex nuts
➇ Lock screw
20.0
24.8
14.4
19.2
4.8
9.6
9.2
14
8.255
15.875
19.0
23.8
● Dimensions
HDR-EA14LFYPG1-( )( )+
HDR-EA26LFYPG1-( )( )+
Part No. A B C8.8
13.6
D E F G
EBG3 3
6
2.5
7.2
F
0.335 0.635
2-ø1.8
2-ø2.3
CBA
D15˚
5 ➂
➄
➀➃
➆
➇➁
POS.#n/2
POS.#1
POS.#1
POS.#n/2
POS.#n
POS.#n/2+1
POS.#n/2+1
POS.#n
0.8
6.616
.71.
6
10.7
RE
F.6
➅
0.635 0.2~0.25FB
POS.#n
POS.#n/2
POS.#1
POS.#n/2+1
ø1.7ø1.1
2.5
0.8
1.7
5
3.5
Recommended PCB layout
● Configuration of product Part No.
HDR- EA ( ) ( ) ( )+LFY P G1-➀ ➁ ➂ ➃ ➄ ➅ ➆
➀ Series name➁ Contact pitch: 0.635 mm➂ No. of contacts: 14 or 26➃ Type of contact
LFY: Right-angle SMT type, female
➅ Lock screwBlank : NoneSL : Provided
➆ Length of lock screwE: 6.6 (standard)K: 3.3 (for HDR-E ( ) LPA-LS)Compatible with B-to-B and B-to-C
➄ Contact platingG1: 0.76 μm or more Gold plate
For use with housing: -SLE: HDR series vertical housing
-SLK: HDR series vertical housing -LS, -LSA
±0.05
±0.03
±0.1
5
±0.
1
±0.1
±0.05
±0.05
±0.1
±0.15
±0.1
±0.1
±0.1 ±0.15
: PAD
4≠
0–
0.1
5
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
0.8mm pitch connector
For PCB
Straight Through hole
EMI shielded
Straight through hole type female connector for PCBHDR-EC( )FDT( )-( )+
Mating connector: HDR series male connector
● Dimensions
● Components
➀ Insulator
➁ Contacts
➂ Shell
➃ Lock screws➄ Board lock pin
● Configuration of product Part No.
HDR- EC ( ) FD T ( )- ( )+➀ ➁ ➂ ➃ ➄ ➅
➀ Series name ➅ Lock screwBlank: NoneSL : Provided(Panel thickness: 1.12 mm)
➁ No. of contacts: 14 or 26➂ Type of contact
FD: Straight through hole type, female➃ With ground contact➄ Contact plating
G2: Min. 0.76 μm Gold plate
£
™
¡
¢
∞
R1.1
2.2
±0
.1
5.2
±0
.1
Y±0.1
X+0.2
A±0.2
F
C
0.8
POS.#2
M2≈0.4
POS.#1
POS.#n
0.8≈(n/2-1)= B
11
.5±
0.3
1.1
2
6±
0.1
55
±0
.3
7.5
±0
.3
1.5
5
2.9
75
E±0.05
B±0.05
D±0.05
0.8±0.03
0.775±0.03
2.9
75
±0
.03
1.1
5±
0.0
31
.15
±0
.03
1.9
6±
0.0
3
0.9
8±
0.0
3
2.125±0.03
POS.#1POS.#2
POS.#n
ø0.65±0.05
ø1±0.05
2-ø1.2±0.05
2-ø1.75±0.08
(PAD)
2-ø2MAX.
(PAD)
E
D
B
0.8
13
26
1
14
15˚
0
R0.5
1.3
2.3
Recommended PCB layout
20
24.8
0.8≈6=4.8
0.8≈12=9.6
8.8
13.6
7.5
12.3
HDR-EC14FDT( )-( )+
HDR-EC26FDT( )-( )+
Part No. A B C D
9.05
13.85
E
19.2
14.4
F
Recommended panel cut-out dimensions
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
0.8mm pitch connector
For PCB
Right-angle Through hole
EMI shielded
Right-angle through hole type female connector for PCBHDR-EC( )LFDT( )-( )+
Mating connector: HDR series male connector
● Dimensions
● Components➀ Shell
➁ Insulator
➂ Contacts
➃ Bracket
➄ Board lock
§ Lock screw
● Configuration of product Part No.
HDR- EC ( ) LFD T ( )- ( )+➀ ➁ ➂ ➃ ➄ ➅
➀ Series name ➅ Lock screwBlank: NoneSLD : Screw lockSLE : Spring lockSLG : Screw lock
➁ No. of contacts: 14, 26 or 50➂ Type of contact
LFD: Right-angle through hole type, female➃ With ground contact➄ Through hole length, contact plating
Blank : 1.65 mm,1 : 2.08 mm,G2 : 2.08 mm, Min. 0.76 μm Gold plate
Min. 0.1 μm Gold plate + Min. 0.5 μm Palladium alloy
(Panel thickness: 1.12 mm)
∞
§
¢
£ ¡™
15
.55
9.5
5 R
EF
.6
A±0.2
4.6±0.05
B±0.05
0.4±0.03
0.8±0.03
E±0.1
B
C
0.8≈(n/2-1)POS.#(n/2)
POS.#2
POS.#2
Lock screw
POS.#n
POS.#n
POS.#2
POS.#1
POS.#n
POS.#1
M2≈0.4
POS.#1
POS.#(n/2)
POS.#(n/2+1)
POS.#(n/2+1)
=D±0.08
1.1
2
2.3
2
6.1
±0
.1
4.5
±0
.11
.15
±0
.03
1.2
±0
.03
1.1
5±
0.0
3
ø0.65 ±0.05
15˚
0.8
0.4
E
6.6
6.65.8
5
3.5
ø0.9+0.15
2-ø2.3±0.1
2-ø3+0.2
-0
-0
Edge of PCBRecommended PCB layout
20
24.8
34.4
14.4
19.2
28.8
8.8
13.6
23.2
HDR-EC14LFDT( )-( )+
HDR-EC26LFDT( )-( )+
HDR-EC50LFDT( )-( )+
Part No. A B C
0.8≈6=4.8
0.8≈12=9.6
0.8≈24=19.2
5.2
10
19.6
D E
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
0.8mm pitch connector
Housing
Vertical
EMI shielded
EMI-filtered vertical plastic housing for standard and thin cableHDR-E( )LP( )( )-( )
● Configuration of product Part No.
HDR- E ( ) ( )( )- ( )LP➀ ➁ ➂ ➃ ➄ ➅
➀ Series name➁ No. of contacts 14, 26 or 50➂ Type of housing: Vertical type➃ Compatible cable
A: Standard cableB: Thin cable
➄ Color of housingBlank: Gray5 : Black
➅ Length of lock springBlank: PCB side lock screw -SLELS : PCB side lock screw -SLK
For use with connectors: HDR series IDC type cable connector HDR-E( )MAG1+, HDR-E( )FAG1+
Required tools: Clamp caulking tools: FHPT-0024A, for 14 contacts cable connectors (Refer to page Tool-10)
FHPT-0022A, for 26 contacts and 50 contacts thin cable connectors
FHPT-0023A, for 50 contacts thick (standard) cable connectors
21.0
25.8
35.4
17.0
21.8
31.4
ø5.6
6≈6.7
7≈8.7
● Dimensions
HDR-E14LPA( )-( )
HDR-E26LPA( )-( )
HDR-E50LPA( )-( )
6≈6.7HDR-E50LPB( )-( )
Part No. A B C
C
B
A
2510
8
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
0.8mm pitch connector
Housing
Vertical
EMI shielded
EMI-filtered screw-lock vertical type plastic housingHDR-E26LPH
Mating connector: HDR series female connector
For use with connector: HDR-E26MAG1+, HDR-E26MSG1+
Required tools: Clamp caulking tools: FHPT-0022A (Refer to page Tool-10)
● Configuration of product Part No.
HDR- E 26 LP H➀ ➁ ➂ ➃
➀ Series name➁ No. of contacts: 26➂ Type of housing➃ Serial number
HONDA
JAPAN
6≈7
26.2
19.2
24.2
Screw size
38
.14
8
34
.59
25
.34
3
M2≈0.4
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
● Configuration of product Part No.
➀ Series name➁ No. of contacts: 26➂ Form of housing
Vertical type housing➃ Serial number
For use with cables: Outside diameter of heavy wire: 10.0-11.7 mm➄ Thickness of relay panel: 1.6 mm
EMI-filtered vertical type plastic housing with mounting hardware for spring-lock, for heavy wires and relay connectionsHDR-E26LPKA+
Mating connector: HDR series of spring-lock type connector
For use with connectors: HDR series of soldering type male or female connector
HDR series of IDC type male or female connector
➀ ➁ ➃➂ ➄
HDR seriesSMTDip Press-in IDC Soldering Crimping OthersWire
wrapping
0.8 mm pitch connector
Housing
For Relay connections
EMI-filtered countermeasures
HDR- E 26 LP K A+
● Components➀
➁
➂
➃
➄
Plastic Cover
Inner Shell B
Inner Shell A
Lock Screw
Plate (For lock screw)
Panel
Connector
24.2
19.2
37
.09
M2≈0.4
Ø11.7
15.37
15
.6
8
13
.2
Ø11.7 Max.
¡
∞
™
£
¢
1.6
● Configuration of product Part No.
➀ Series name➁ No. of contacts: 26➂ Form of housing
Vertical type housing➃ Serial number
For use with cables: Outside diameter of cable: 10.0-11.7 mm
EMI-filtered screw-lock vertical type plastic housing for heavy wiresHDR-E26LPK+
Mating connector: HDR series of screw-lock type connector
For use with connectors: HDR series of soldering type male or female connector
HDR series of IDC type male or female connector
➀ ➁ ➃➂
Ø11.7
24.2
25
.34
37
.09
38
.14
M2≈0.4
19.2
13.2
8
11.6
13
¡
™
£
¢
Connector
HDR seriesSMTDip Press-in IDC Soldering Crimping OthersWire
wrapping
0.8 mm pitch connector
Housing
Vertical type
EMI-filtered countermeasures
HDR- E 26 LP K+
● Components➀
➁
➂
➃
Plastic Cover
Inner Shell B
Inner Shell A
Thumb screw
7
6.4
21.8
25.8
35
8
¡
∞
§
™
¢
£
● ComponentsPlastic Cover A
Plastic Cover B
Inner Shell B
Button
Inner Shell A
Lock spring
➀
➁
➂
➃
➄
➅
● Configuration of product Part No.
➀ Series name➁ No. of contacts: 26➂ Form of housing
Vertical type housing➃ Serial number
EMI-filtered spring-lock vertical type plastic housingHDR-E26LPJ+
Mating connector: HDR series of spring-lock type connector
For use with connectors: HDR series of soldering type male or female connector
HDR series of IDC type male or female connector
➀ ➁ ➃➂
HDR seriesSMTDip Press-in IDC Soldering Crimping OthersWire
wrapping
0.8 mm pitch connector
Housing
Vertical type
EMI-filtered countermeasures
HDR- E 26 LP J+
EMI-filtered vertical type plastic housing with mounting hardware for spring-lock, for thin wires and relay connectionsHDR-E26LPHA+
● Configuration of product Part No.
➀ ➁ ➂ ➃
Mating connector: HDR series of screw-lock type connector
For use with connectors: HDR series of soldering type male or female connector
HDR series of IDC type male or female connector
● Components➀
➁
➂
➃
➄
Plastic Cover
Inner Shell B
Inner Shell A
Lock Screw
Plate (For lock screw)
HONDA
JAPAN
24.2
19.2
34
.59
6.7
6.0
8
Ø6.5 Max.
¡
∞
™
£
¢Panel
Connector
1.6
➀ Series name➁ No. of contacts: 26➂ Form of housing
Vertical type housing➃ Serial number
For use with cables: Outside diameter of thin wire: 5.8-6.5 mm➄ Thickness of relay panel: 1.6 mm
➄
HDR seriesWire
wrappingOthers Crimping Soldering IDC Press-in DipSMT
0.8 mm pitch connector
Housing
For Relay connections
EMI-filtered countermeasures
HDR- E 26 LP H A+
0.8≈12=9.6
¡
15.6
0.8Pos.#13Pos.#1
Pos.#14Pos.#26
13.6
15˚
5.4
£
™ ¢
0.8≈12=9.6
0.8Pos.#26 Pos.#14
Pos.#13 Pos.#1
0.8≈12=9.6
0.8
69
.4
Soldering type female connector for cablesHDR-E26FSG1+
➀ Series name➁ With metal shell➂ No. of contacts: 26➃ Form of housing
FS: Soldering type, female connector, AWG#28Insulator OD: 1.0 mm max.
➄ Contact platingG1: Min. 0.76 mm Gold plate
● Configuration of product Part No.
➀ ➁ ➂ ➃ ➄
Mating connector: HDRA series, male connector
For use with connectors: HDR-E26LPH( ), HDR-E26LPJ+, HDR-E26LPK( ), HDR-E26ALP( )+
● Components➀
➁
➂
➃
Female Contact
Shell
Insulator
Spacer
HDR seriesWire
wrappingOthers Crimping Soldering IDC Press-in DipSMT
0.8 mm pitch connector
For cables
Soldering type
EMI-filtered countermeasures
HDR- E 26 FS G1+
19.2
15.6
29
8
24.8
18
.85
19
.1
¡
∞
¢
£
™
7.5
19
.1
6.7
5.9
14
.82
5
PCB-side connector
EMI-filtered screw-lock right-angle type plastic housingHDR-E26ALPA+
➀ Series name➁ No. of contacts: 26➂ Form of housing
Right-angle➃ Serial number
For use with cables: Outside diameter of cable: 6.2-6.8 mm
● Configuration of product Part No.
➀ ➁ ➂ ➃
Mating connector: HDR series of screw-lock type connector
For use with connectors: HDR series of soldering type male or female connector
HDR series of IDC type male or female connector
● Components➀
➁
➂
➃
➄
Plastic Cover A
Plastic Cover B
Inner Shell B
Inner Shell A
Thumb screw
HDR seriesWire
wrappingOthers Crimping Soldering IDC Press-in DipSMT
0.8 mm pitch connector
Housing
Right-angle
EMI-filtered countermeasures
HDR- E 26 ALP A+
Ø9
33.8
25
.34
3
0.8
34
.59
38
.14
M2≈0.4
28.8
8
10
¡
™
£
¢
Connector
HDR-E50MSG1+
● Components➀
➁
➂
➃
Plastic Cover
Inner Shell B
Inner Shell A
Thumb screw
● Configuration of product Part No.
➀ Series name➁ No. of contacts: 50➂ Form of housing
Vertical type housing➃ Serial number
EMI-filtered screw-lock vertical type plastic housingHDR-E50LPH
Mating connector: HDR series of screw lock type connectors
For use with connectors: HDR-E50MSG1+
HDR-E50M( )G( )+
➀ ➁ ➃➂
HDR seriesSMTDip Press-in IDC Soldering Crimping OthersWire
wrapping
0.8 mm pitch connector
Housing
Vertical type
EMI-filtered countermeasures
HDR- E 50 LP H