VEHICLE SECURITY SYSTEMINSTALLATION INSTRUCTION

PART NUMBER

FOR : A*A30R-AW*G*W

TOYOTA MOTOR CORPORATION

RAV4 (RHD)

SECURITY KIT

08586-4A921FITTING KIT

1 07-2007

Precautions

2 07-2007

Fitting Kit Contents (08586-4A921)

[1] [2] [3]

[4] [5]

[6] [7] [8]

[6]

[1]

[2]

[3]

[4]

Pos. No. Q'tyDescription

1

1

1

1

[5]

2

[8]

Wire Harness

ECU Mounting Bracket

GLASS BREAKAGE CONTROL UNIT

Microphone

Bolt (M6x18)

Small Foam Tapes

Splicing Connector

1

[7] Wire Ties (150mm) 4

1

3 07-2007

Vehicle DisassemblySet the seat cover and floor mat before starting operation. Be careful do not scratch anddamage the vehicle.

1. Remove the luggage cover.

2. Remove the floor board.

3. Remove the floor box (A).

Luggage Cover

Fig. 1

Fig. 2

Fig. 3

Floor Board

Clips (x4)

Clips (x2)

Floor Box (A)

4 07-2007

Fig. 6

Fig. 5

5. Fold down driver and passenger rear seat back.

6. Remove the floor box (B).

7. Remove the driver side rear door scuff plate.

8. Pull up the driver side weather strip.

Rear Door Scuff Plate

Clips (x2)Weather Strip

Rear Seat Back

4. Remove the deck trim cover.

Clips (x6)

Deck Trim Cover

Fig. 4

Clips (x3)

Clips (x2)

Clips (x2)Floor Box (B)

Screws (x2)

Screws (x2)

5 07-2007

Fig. 8

12. Remove the seat belt anchor.

13. Remove two screws from the luggage side trim.

Fig. 7

9. Remove two hooks from the luggage side trim.

10. Remove the seat fold down lever cover.

11. Pull up the weather strip.

Luggage Side Trim

Hook

Hook

Bolt

Bolt

CoverClips (x2)

Clips (x2)

Weather Strip

Seat Fold DownLever Cover

Bolt

Cover

Fig. 9

14. Remove the driver side luggage side trim.

Claw (x4)

Clips (x5)

Luggage Side Trim

Screws (x2)

Luggage Side Trim

6 07-2007

Fig. 10

15. Remove front door scuff plate.

Fig. 11

12. Remove the seat belt anchor.

13. Remove the center pillar cover.

Fig. 12

14. Remove the clip from the cowl cover.

15. Remove the cowl cover.

Front Door Scuff Plate

Clips (x3)

Bolt

Cover

Clips (x4)

Clips (x2)

Clips (x2)

Clip

Center Pillar Cover

Cowl Cover

7 07-2007

GBS ECU/ Microphone and Wire Harness InstallationSet the seat cover and floor mat before starting operation. Be careful do not scratch anddamage the vehicle.

1. Turn the GBS adjustment screw on the GBS ECU to the "8" position.

Fig. 13

GBS ECU

Mounting Bracket

GBS ECU

Fig. 14

2. Insert the mounting bracket into the indicated bracket slot on the GBS ECU.

Insert the mounting bracket into thecorrect ECU's slot.

Cut!

Fig. 15

Small Foam Tape

Small Foam Tape(Half Cut)

3. Cut the small foam tape in half, then wrap it to the microphone harness as shown.

7 07-2007

Fig. 16

4. Install GBS ECU using the supplied kit's bolt, then install the GBS ECU to the driver side rear luggagearea as shown.

5. Use the existing vehicle bolt to secure the TVSS harness' the ground terminal.

6. Secure the TVSS harness's root of the ground terminal on vehicle harness with TVSS Wire Tie.

7. Route the TVSS harness toward the GBS ECU, Securing it to the vehicle harness with 2 wire ties.

8. Connect the TVSS harness' 8P white connector to GBS ECU.

9. Connect the TVSS harness' 2P white connector to microphone.

Press the microphone to the bracket firmly.

10. Secure the TVSS harness to vehicle harness with 3 wire ties.

11. Route the TVSS harness toward rear door scuff plate.

Bracket

Marker LineMicrophone

TVSS Harness

Wire TieBolt

Bolt

GBS ECU

TVSS Harness'8P

Wire Ties

Wire Ties (x3

TVSS Harness' 2PConnector (White)

Ground

8 07-2007

1

2

3

4

12. Route the TVSS harness toward therear door scuff plate , Securing it to thevehicle harness with 4 wire ties.

Fig. 17

Wire Ties (x4)

Fig. 18

Wire Ties (x2)

13. Route the TVSS harness toward thecenter pillar , Securing it to the vehicleharness with 2 wire ties.

Fig. 19

14. Route the TVSS harness toward thefront door scuff plate, Securing it to thevehicle harness with 2 wire ties.

Wire Ties

9 07-2007

Fig. 20

15. Route the TVSS harness toward thedriver's side cowl cover , Securing it to thevehicle harness with 4 wire ties.

Wire Ties

16. Remove vehicle's 16p connector from cowl side J/B

Fig. 21

Fig. 22

Vehicle's 16PConnector

Fig. 21

17. Locate the Vehicle's 16p connector'spink wire(2nd row, 3rd space from theleft). Attach the TVSS harness's pink wirewith splicing connector.

Vehicle's 16PConnector

Pink Wire

Splicing Connector Vehicle's Pink

Wire

TVSS's PinkWire

10 07-2007

REFIT THE REMOVED PARTS.

Fig. 23

18. Remove Vehicle's 14p connector fromcowl side J/B

19. Connect the TVSS 14p connector tothe Vehicle's 14p connector.

20. Secure the TVSS connector to vehicleharness with 1 wire tie.

Wire Tie

Vehicle's14P

TVSS 14PConnector

TVSS 14PConnector

Vehicle's14P

Fig. 24

11 07-2007

Accessory Function CheckChecklist - these points MUST be checked to ensure a quality installation.

Check: Look For:

The horn stops sounding.All the lights stop flashing and/ or turn off.The status monitor’s LED turn off, but animmobilizer’s LED remains on.

Insert the key into the driver’s door keycylinder and turn it toward the back of thevehicle to stop the alarm.

Fit the appropriate fuse before beginning.Close the hood before beginning.

Press and release the remote control’s lockbutton to start the system’s arming process.

The tail and marker lights flash once.The buzzer chirps once.All doors lock.The Security LED lights up.

Wait 30 seconds. After 30 seconds, the security indicator startsflashings; the system is now armed.

With the tip of key, tap the centerof the rear window to trigger the"warn away" alarm.

The horn sounds repeatedly.The interior lights turn on.The headlights flash repeatedly.The tail and marker lights flash repeatedly.The Security LED lights up.

9 07-2007