06/16 MARKET SPECIFIC CATALOG METAL ROOFING &...
Transcript of 06/16 MARKET SPECIFIC CATALOG METAL ROOFING &...
Fastening Systems • SealantsFlashings • Tools • Accessories
CR
TRIANGLE FASTENERCORPORATION
FASTENING SYSTEMS AND SOLUTIONSFOR COMMERCIAL CONSTRUCTION
800.486.1832www.trianglefastener.com
Visit our website for the most up-to-date product information
METAL ROOFING & SIDINGMETAL BUILDING / POST FRAME
MARKET SPECIFIC CATALOG06/16
CR
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD274.0616
BLAZER® Self-Drilling Fasteners Hex Washer Heads
GET-A-Grip® Rivets and Tools
CONCEALOR® Pancake Head Screws
SizesDiameters: #10, #12, 1/4”, 5/16” Lengths: 1/2” to 10”Material: Carbon Steel, 410 Stainless SteelTRI-SEAL® 1,000 Hrs Salt Spray coated
1/4-14 Lap / DP1 / VRT
#12-14 DP3
#10-16 DP3
#12-24 DP5
#12-24 DP4.5
1/4-14 DP3
1/4-20 DP5
Any fastener can be painted at one of our 6 In-house Kalida Kote paint facilities!
SizesDiameters: #10, #12, 1/4” Lengths: 3/4” to 10”Material: Carbon Steel, 410 Stainless SteelSecurity Screws!
BLAZER® Bonded Sealer
SizesDiameters: #12, 1/4” Lengths: 3/4” to 3”Material: Carbon Steel / TRI-SEAL
BLAZER® Flange Sealer
SizesDiameters: #12, 1/4” Lengths: 3/4” to 3”Material: Carbon Steel / TRI-SEAL 304SS Head
BLAZER® Stainless Steel Head
SizesDiameters: #12, 1/4” Lengths: 3/4” to 3”Material: Carbon Steel / TRI-SEALZinc Head
BLAZER® Zinc Head
SizesDiameters: #14 , 1/4”, #17, 3/8” Lengths: 3/4” to 8”Head Style: HH & HWHMaterial: Carbon Steel 304SS - 410SS
SELF-TAPPERS
Sizes / Pancake HeadDiameter: #10, #12, 1/4”, #14Length: 5/8” to 9”Materials: Carbon Steel 410 Stainless Steel 304 Stainless Steel
#10-13 GP
#12-14 DP3
#14 DP1
#10-9 GP ULP
1/4 DP3
#10 DP3
SizesDiameters: #12-14, #12-24, 1/4-14, 1/4-20 Lengths: 1-1/4
Shoulder Clip Screws
SizesDiameters: #10, #12, 1/4” Length: 3/4" & 7/8”
Framing | Trim Screw
SizesDiameters: #10, #12, 1/4” Lengths: 1” to 3-3/4”
Wood to Metal Fasteners
SizesDiameters: 3/8”, 1/2”, 5/8”, 7/8”, 1”, 1-1/4”Lengths: 1” to 3-3/4”Black Phos and Zinc Yellow A307 & A325
Structural Bolts
BULB-TITE Rivet and Tools
GET-A-GRIP Blind Rivets and Tools
FAB-LOK Rivet
GROMMET SEAL Rivet
SizesDiameters: #10, #12, #14 Lengths: 1” to 4”Materials: Carbon, Stainless, Zinc Head, Stainless Head
PANEL-TITE® Screws
Pat. No. 8,360,701
METAL BUILDING | METAL ROOFING | POST FRAMENEED-IT-NOW PRODUCTS
StressLess BURR BUSTER
#12-24 DP5
1/4 DP3
5/16-12 DP3
#12-11 GP
2
CR
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD275.0616
Choose from major brands and types of levels, lasers, and tape measures.
We stock all the major brands of power tools for drilling, sawing, cutting, driving, shearing, and grinding!
Materials: Carbon Steel - Zinc PlatedHot-dipped Galvanized 304 & 316 Stainless Steel
SizesDiameters: 1/4” to 1-1/4” Lengths: 1-3/4” to 12”
SizesDiameters: 3/16” to 1/2” Lengths: 1-1/4” to 14”Materials: Carbon and Stainless
Base Angle to concrete.
Wedge
Sleeve
Wide selection of hand and power caulking guns!
BRACER® , STRESS-LOK® , DANDI-EYE® Power Tools Corded and Battery Powered
Caulking Guns
Accessories
CONCRETE ANCHORSWedge and Sleeve Anchors
BASE ANGLE ATTACHMENT
Bent Anchor Bolts
Misc. Concrete Anchors
Lasers, Levels, and Measuring Tools
Bracing Hillside Washers - Cable Bracing Assembly - Forged Eyebolts
Color matched to your panel.
KALIDA-KOTE® Touch-up Paint Pens and Bottles
Use to align holes and tighten bolts.
Spud Wrench
Full line of hand snips and clamps for steel framing fabrication.
Snips and Locking Clamps
Safety Equipment / Storage Job Boxes
Full line power cords and power blocks.
Sizes12/3, 14/3, 16/3 wire
Power Cords
Harness, Hard Hats, Safety Glasses, Dust Masks, First Aid Kits, Hearing Protection & Storage boxes
We stock a large selection of professional grade...Chop-saw bladesCarbide bladesDrill bitsReciprocating bladesAbrasive wheels
Insert Bits and Power BitsPhillips, Square, Torx, Quadrex
Nutsetters1/4”, 5/16”, 3/8”, 7/16”
Saw BladesCutoff WheelsAll sizes and types
Bit HoldersMagnetic and locking ring style
Drill BitsAll sizes and types up to 12" long!
Many sizes available to anchor structure.
Choose from MS, silicone, butyl.
Single bead, double bead, and triple bead available.
EPDM - Silicone - Colors - RetroFit Applications. 35-yr warranty!
Sizes to fit all major panel profiles!
Seaming tapes for blanket insulation.
Flash a variety of metal roof conditions.
Expands to fill the gaps.
Caulks Sealants and Flashings
Butyl Tape
PIPE-MASTER® Pipe Flashing
CLOSE-TITE® Panel Closure
Universal Closure
Facing Tape - Polypropylene
Dek Strip / End Cap Flashing
METAL BUILDING | METAL ROOFING | POST FRAMENEED-IT-NOW PRODUCTS
JC021715
3
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD22.0616
Bagged 250 pcs. per bag for your convenience!
Description
Attachment Thickness
(Max) Part NumberBox
QuantityWT Per
Box
A #10-13 X 1” GP Long-life TRI-SEAL® coated 1" 10100SPCGCSTS 5,000 pcs 36.0 lbs.
A-1 #10-9 X 1” Type 17 Zinc Plated | Interior Use Only 1" 10100SPC17CSTSZP 5,000 pcs 36.0 lbs.
B #10-13 X 1” GP 302 Stainless Steel 1" 10100SPCGS3 5,000 pcs 39.0 lbs.
C #10-9 X 1-1/8” TYPE 17 Long-life TRI-SEAL® coated 1-1/8" 10112SPC17CSTS 5,000 pcs 40.0 lbs.
D #10-13 X 1-1/2” GP Long-life TRI-SEAL® coated 1-1/2" 10150SPCGCSTS 3,000 pcs 31.0 lbs.
E #10-13 X 1-1/2” GP 302 Stainless Steel 1-1/2" 10150SPCGS3 3,000 pcs 32 lbs.
F #10-13 X 2” GP Long-life TRI-SEAL® coated 2" 10200SPCGCSTS 1,500 pcs 19.0 lbs.
G #12-11 X 1” GP Long-life TRI-SEAL® coated 1" 12100SPCGCSTS 5,000 pcs 44.0 lbs.
H #10-16 X 5/8” DP3 .0003” Zinc and Yellow .125" 10062SPC3CS 5,000 pcs 28.0 lbs.
I #10-24 X 5/8” DP3 .0003” Zinc and Yellow .125" 10062PPC3CSYZ 5,000 pcs 27.0 lbs.
J #10-16 X 1” DP3 .0003” Zinc and Yellow .250" 10100SPC3CS 5,000 pcs 37.0 lbs.
K #10-16 X 1” DP3 410 Stainless Steel .250" 10100SPC3S4 5,000 pcs 37.0 lbs.
L #10-16 X 1-1/2" DP3.0003" Zinc and Yellow 1" 10150SPC3CS 3,000 pcs 32.0 lbs
M #10-16 x 2" DP3.0003" Zinc & Yellow 1.5" 10200SPC3CS 1,500 pcs 21.0 lbs.
N #12-14 X 1” DP3 Long-Life TRI-SEAL® coated .250" 12100SPC3CSTS 5,000 pcs 43.0 lbs.
O
#12-24 X 1-1/4” DP5 Long-Life TRI-SEAL® coated .500" 12125SPC5CSTS 4,000 pcs 42.8 lbs.
#12-24 X 1-1/2” DP5 Long-Life TRI-SEAL® coated .625" 12150SPC5CSTS 4,000 pcs 43.8 lbs.
P 1/4-14 X 1” DP3 .0003” Zinc and Yellow .250" 14100SPC3CS 2,500 pcs 27.0 lbs.
Sizes
CONCEALOR® low profile head fasteners are engineered to perform in a variety of applications. They are specified in many metal roofing systems to attached SSR clips to metal or wood. They are easy to install and provides optimal strength.
PANCAKE HEAD SCREWSPiercing Point and Drill Point
#10, #12, & 1/4" PIERCING POINTS AND DRILL POINTS
We can assemble CONCEALOR® with
a bonded sealing washer that locks out weather and looks appealing!
We can color match to your exact
requirements in three days or less!
WOOD OR THIN METAL
METAL SUBSTRATES
A
B
C
D
E
F
G
H
I
J
K
N
P
SPECIAL APPLICATIONS
#2 Square Recess Drive
O
Army Corps of Engineers
L
M
Zinc Plated available for interior use only.
A-1
®
Installation: Do not use impact drivers! Use 2,500 RPM max variable speed screw drivers with torque control or depth sensing nosepiece.
4
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD23.0616
Trust the originalUltra Low Profile fastener!
DescriptionDrilling
Thickness Part NumberBox
QuantityWT Per
Box
A #10-9 X 1-1/8” ULP (CS) Long-life TRI-SEAL™ coated <= 24 ga. 10112SPCUGCSTS 5,000 31.0 lbs
B #10-9 X 1-1/8” ULP (CS) Zinc Plated Interior Use Only <= 24 ga. 10112SPCUGCSZP 5,000 31.0 lbs
C #10-9 X 1-1/8” ULP (410 SS)Passivated <= 24 ga. 101125SPCUGS4 5,000 32.0 lbs.
D #10-9 X 1-5/8” ULP (CS) Long-life TRI-SEAL™ coated <= 24 ga. 1062SPCUGCSTS 3,000 34.0 lbs.
E #10-9 X 2-1/8” ULP(CS)Long-life TRI-SEAL™ coated <= 24 ga. 10212SPCUGCSTS 1,500 17.0 lbs.
Sizes
TECHNICAL INFORMATION
The CONCEALOR® ULP screws are engineered to attach standing seam roof clips to wood. They are the preferred screw for attaching clip-less metal roof panels, are easy to install, and provide optimal strength. ULP's are supplied with TRI-SEAL® 1,000-hours salt spray coating which can be used in treated and fire treated lumber.
Torsional 60 lb-in
Tensile 1,520 lbs. min.
Shear 1,150 lbs. min.
Pullout - Average Ultimate in Pounds
FastenerDia. & Point
Wood Type1/2”
Plywood5/8”
Plywood3/4”
Plywood7/16” OSB
19/32” OSB
23/32” OSB
2 x 4 SYP
#10-9 GP 383 395 574 136 356 514 813
Fastener Strength
Description: #10-9 Gimlet Point self-tapping screw Head Style: Ultra low pancake head with taper. Drive System: #2 square recess Head Thickness: .040” Material: C1018 carbon steel 410 Stainless steel (Copper Roofing Compatible) Heat Treat: Case hardened to ANSI/ASME B18.6.4 specification Finish Carbon Steel: TRI-SEAL™ long-life coating (1,000hrs. salt spray) Stainless Steel: Passivated (1,000hrs. salt spray)
Thread Detail Major Diameter: .195” Minor Diameter. .125” Stress Area: .01267 in2
Bagged 250 pcs. per bag for your convenience!
ULTRA LOW PROFILE FASTENERS
Coarse threadPulls fastener tight into the wood.
Minimum 1" thread lengthProvides full thread engagement for increased pullout!
Sharp gimlet pointFast penetration into steel clips up to 24 gauge thick!
50% thinner than a standard pancake head.No more dimpling of the panel.
Special taperIncrease head strength and countersinks into the wood.
A
C
D
CONCEALORULTRA LOW PROFILE ULP®
Need it Ultra Low?
Available in lengths up to 2-1/8"!
Rev 040711Farabaugh Engineering Test: Project No. T279-10
B
CS = Carbon Steel - C1018 / C1022410 SS = 410 Stainless Steel
Zinc Plated available for interior use only.
#2 Square Recess Drive
E
TM
Installation: Do not use impact drivers! Use 2,500 RPM max variable speed screw drivers with torque control or depth sensing nosepiece.
5
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD25.0616
#14 DP1 CONCEALOR® with TRI-SEAL® coating provides the best corrosion protection in the industry!
Salt spray tests confirm that our TRI-SEAL® coating provides over 10 times more resistance to red rust than black epoxy coated screws. It is engineered to perform in a variety of applications.
• Largest selection in the industry.
• #2 Square recess for driving stability.
• Fasten into wood or metal up to 16ga consistently
• FM approved for preliminary attachment of nail base.
#14-13 DP1 Pancake Head Screws
#2 SquareRecess Drive
*4-1/2” Thread LengthTRI-SEAL™ Coated 1,000 hour salt spray. Exceeds ASTM B633
15 cycles Kesternich. Exceeds FM 4470.Great for treated lumber and exposed environments.
DescriptionAttachment Thickness Part Number
Carton Quantity
Wt Per Carton
#14-13 x 1-1/2” DP1 <=1.000” 14150SPC1CSTS 2,500 pcs 34 lbs
#14-13 x 2” DP1 <=1.500” 14200SPC1CSTS 1,000 pcs 18 lbs.
#14-13 x 3” DP1 .125” - 2.500” 14300SPC1CSTS 1,000 pcs 24 lbs.
#14-13 x 4” DP1 .125” - 3.500” 14400SPC1CSTS 500 pcs 16 lbs.
#14-13 x 4-1/2” DP1 .625” - 4.000” 14450SPC1CSTS 500 pcs 17 lbs.
#14-13 x 5” DP1* 1.125” - 4.500” 14500SPC1CSTS 500 pcs 19 lbs.
#14-13 x 6” DP1* 2.125” - 5.500” 14600SPC1CSTS 500 pcs 23 lbs.
#14-13 x 7” DP1* 3.875” - 6.500” 14700SPC1CSTS 500 pcs 28 lbs.
#14-13 x 8" DP1* 4.875" - 7.500" 14800SPC1CSTS 250 pcs 17 lbs.
#14-13 x 9" DP1* 5.875" - 8.500" 14900SPC1CSTS 250 pcs 19 lbs.
Longer 4-1/4" thread on 5", 6", 7", 8", 9" lengths.
CONCEALOR® with Buttress Thread
Ordinary Thread Form
“Flat" thread keeps the joint tight
A “Tapered" thread tends to cause the
joint to loosen
Here is why we use a special thread...We use a buttress thread form that provides exceptional clamping loads. It is specified in many metal roofing systems to attached SSR clips over rigid insulation into metal deck.
Sizes
®
Installation: Do not use impact drivers! Use 2,500 RPM max variable speed screw drivers with torque control or depth sensing nosepiece.
6
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD26.0616
#14 DP3 CONCEALOR® pancake head screws are designed for heavy gauge applications and can drill and tap up to 1/4” steel. The 1/4-14 thread produces greater strength and resists bending compared to smaller diameter screws.
These screws are coated with TRI-SEAL™ long-life coating that exceeds ASTM B633 specifications providing 1,000-hours salt spray performance, and FM4470 per ASTM G87 Sulfur Dioxide Test.
DescriptionAttachment Thickness Part Number
Carton Quantity
Wt Per M Pcs
A 1/4-14 X 1” DP3 .0003” Zinc and Yellow 1/4” Max 14100SPC3CS 2,500 pcs 27#
B 1/4-14 x 2” DP3 1.000” Max 14200SPC3CSTS 1,000 pcs 19#
C 1/4-14 x 3” DP3 1.375” to 2.125” 14300SPC3CSTS 1,000 pcs 27#
D 1/4-14 x 4” DP3 1.625” to 3.125” 14400SPC3CSTS 500 pcs 34#
E 1/4-14 x 5” DP3 2.750” to 4.125” 14500SPC3CSTS 500 pcs 42#
F 1/4-14 x 6” DP3 3.750” to 5.125” 14600SPC3CSTS 500 pcs 50#
G 1/4-14 x 7" DP3 4.750" to 6.125" 14700SPC3CSTS 500 pcs 50#
H 1/4-14 x 8" DP3 5.750" to 7.125" 14800SPC3CSTS 250 pcs 34#
SPECIAL HEAD DESIGN
• 5/8” diameter head increases pullover strength and minimizes dimpling.
• #3 square recess drive provides stability during installation.
Use to attach a variety of material to steel up to 1/4” thick!
1/4-14 DP3 - DRILL AND TAP UP TO 1/4" THICK STEEL
1/4” DP3 CONCEALORWith TRI-SEAL® 1,000-hrs Coating
ARCHITECTURALINSULATED PANELS
NAILBASE
METAL ROOF CLIPSSTRUCTURAL
INSULATED PANELS
SPECIAL APPLICATIONS
Physical Properties Thread Diameter: 1/4” (.250” nominal)Thread Pitch: 14 Head Diameter: .625"Head Thickness: .100"Material: C-1022 Case Hardened per SAE J-78
REV.JES082712
Special “un-threaded” section is engineered to eliminate “jacking” when installing insulated panels!
A
B
C
D
E
F
G
H
Army Corps of Engineers.0003" Zinc & Yellow
®
TOOLING: Install using a 2,000 RPM screw-gun with torque control. (DeWalt DW267) Do not use impact tools.
7
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD28.0716
Pullout In Wood - Average Ultimate in Pounds
Pullout In Steel - Average Ultimate in Pounds
FastenerDia. & Point
Wood Type1/2” Ply
5/8” Ply
3/4” Ply
7/16” OSB
19/32” OSB
23/32” OSB
2 x 4 SYP
#10-13 GP 375 505 654 166 357 442 737#10-9 GP 383 395 574 136 256 514 813#12-11 GP 418 455 624 *164 379 573 918#14-13 DP1 434 475 626 153 327 457 991
The chart below provides general information with regard to corrosion resistance of various plating and coatings. Contact TFC for detailed information.
Screw Tee Clip 24 ga. (Ave. Ultimate)
Zee Clip 24 ga. (Ave. Ultimate)
#10 DP3 415 lbs. 510 lbs.
#12 GP 430 lbs. 692 lbs.
#14 DP1 407 lbs. 677 lbs.
Decking fasteners tested with full thread embedment. 2 x 4 SYP with 1” embedment
Fastener Diameter& Material
Minimum UltimateThread
DiameterTensile (lbs.)
Shear (lbs.)
Torsional (lbs-in)
#10-9 / Carbon 0.200” 1,520 1,150 60#10-9 / 410SS 0.200” 2,500 1,625 85#10-13 / Carbon 0.195” 1,725 1,125 60#10-13 / 302SS 0.195” 1,040 701 45#10-16 / Carbon 0.186” 2,100 1,400 61#10-16 / 410SS 0.186” 3,200 2,130 92#12-11 / Carbon 0.220" 2,500 2,000 95#12-14 / Carbon 0.212” 2,778 2,000 100#12-14 / 302SS 0.212” 2,630 1,978 85#12-24 / Carbon 0.213” 3,450 2,420 1101/4-14 / Carbon 0.243” 3,850 2,600 150#14-13 / Carbon 0.235” 3,620 2,500 115
DISCLAIMER: ALL DATA AnD SPECIFICATIOnS ARE BASED On LABORATORY TESTS. APPROPRIATE SAFETY FACTORS ShOULD BE USED BY ThE USER OR SPECIFIER. DETERMInInG ThE PROPER FASTEnER IS ThE RESPOnSIBILITY OF ThE USER OR SPECIFIER. BECAUSE APPLICATIOn COnDITIOnS vARY, wE ASSUME nO LIABILITY FOR ThE USE OF ThIS InFORMATIOn.
Fastening Tips• A minimum of 3 factors of safety should be used for most self-drilling or self-tapping
fasteners in metal | 5-6 for wood. Consult a design professional for appropriate values.
• Install fastener perpendicular to the work surface and tighten to no more than approximately 70% of the torsional strength.
• Allow at least three full threads to extend beyond the material. For wood applications, allow 1” minimum embedment or full thread embedment in plywood and OSB for optimal pullout resistance.
* Berridge Clips
TECHNICAL DATA
Thread Type and Point
Thread Major Dia. Material
head Dia.
head Thickness Drive Finish
#10-16 DP2 .180” C1022 .435” .080” #2 Sq .0003” Zinc & Yellow
#10-24 DP3 .185” C1022 .435” .080” #2 Sq .0003” Zinc & Yellow
#10-13 GP .190” C1022302 SS .450” .080” #2 Sq TRI-SEAL™ Coated
Passivated
#10-16 DP3 .180” C1022410 SS .450” .080” #2 Sq .0003” Zinc & Yellow
.0002" Zinc & Clear
#10-9 GP (ULP) .200” C1022410 SS .435” .040” #2 Sq TRI-SEAL™ Coated
Passivated
#12-11 GP .220” C1022302 SS .450” .080” #2 Sq TRI-SEAL™ Coated
Passivated#12-14 DP3(SD300) .210” C1022
304 SS.450”.500”
.080”
.090”#2 Sq
T-30 Torx .0003” Zinc & Yellow
#12-24 DP5 .210” C1022 .425” .110” #3 Sq .0003” Zinc & YellowTRI-SEAL™ Coated
#14-13 DP1 .235” C1022 .500” .090” #2 Sq .0003” Zinc & YellowTRI-SEAL™ Coated
1/4-14 DP3 (1")(2", 3", 4", 5", 6") .245” C1022 .500”
.625".080”.100"
#2 Sq#3 Sq
.0003” Zinc & YellowTRI-SEAL™ Coated
F
®
REv JS110615Farabaugh Engineering Test: Project no. T279-10 & * T282-15
PULLoVEr
PErForMANCE SPECIFICATIoNS
FASTENEr ProPErTIES
TooLINg | Do not use impact tools!
SALT SPrAy
REv JS110615
Screw-gun RPMCarbon Steel & 410SS Screws: 2,500 RPM Max.DP5, 1/4" & 5/16" DP3: 2,000 RPM Max.302 & 304 Stainless Steel Tapping Screws: 1,000 RPM Max. For optimal performance, use screw-guns with torque control feature. DO NOT OVER-TORQUE FASTENERS.
SALT SPRAY Per ASTM F1941 & B117 (0% red rust) Rev. 120313Carbon steel and 410 stainless steel materialsCoating Salt Spray.00015” min. (3 um) zinc plating with clear chromate 15hrs.0002” min. (6um) zinc plating with clear chromate 24hrsPassivated 410 Stainless Steel 48hrs.0003” min. (8 um) zinc plating with clear chromate 48hrs.0003” min. (8 um) zinc plating with yellow di-chromate 120hrs.0005” min. (12 um) zinc plating with clear chromate 72hrs.0007” min. (14 um) mechanical zinc with clear chromate 72hrsEpoxy (E-Coat) (ACQ Compatible) 100hrsTRI-SEAL™ Long-life coating 1,000hrsPassivated 302 & 304 SS >2,000hrs
REV.JES082712
FASTENEr MATErIAL SELECTIoN BASED oN THE gALVANIC SErIES oF METALS
Revised: 1110615JS
KeyA. The corrosion of the base metal is not increased by the fastener.B. The corrosion of the base metal is slightly increased by the fastener.C. The corrosion of the base metal may be considerably increased by the fastener material.D. The plating on the fastener is rapidly consumed.E. The corrosion of the fastener is increased by the base metal.
FASTEnER MATERIALSTEEL
Zinc PlatedSTAInLESS STEEL
Type 410STAInLESS STEELType 302, 304, 316 ALUMInUM
BA
SE M
ETA
L Zinc | Galvanized | Zn/Al Coated Steel A C C B
Aluminum A not Recommended B ASteel / Cast Iron A,D C B A
Brass, Copper, Bronze A,D,E A B A,EStainless Steel
300 Series A,D,E A A A,E
Fastener Information(Drill Points)
PULLOUT | ULTIMATE LOAD IN POUNDSGrade 80 and Grade 50 Steel per ASTM A792/A1011/A653/A572/A529
Calculated Values In Accordance to AISI S100 | Section E4
Thread Type
Nom Dia.(in.)
Grade 8062Ksi Min.
Grade 5065Ksi Min. Steel
26 Ga.(.018")
25 Ga.(.021")
24 Ga.(.024")
22 Ga.(.030")
20 Ga.(.036")
18 Ga.(.048")
16 Ga.(.060")
14 Ga.(.075")
12 Ga.(.105")
1/8"(.125")
10 ga(.135")
1/4"(.250")
3/8"(.375")
1/2"(.500")
#10-16 .190" 180 220 251 315 378 504 630 787 1102 1312
#10-24 .190" 787 1102 1312
#12-14 .216" 205 251 286 358 430 573 716 895 1253 1492 1611
#12-24 .216" 1492 1611 2984 *4475 *5967
#14-13 .235" 223 273 312 390 467 623 779 974
1/4-14 .250" 829 1036 1450 1727 1865 3453 *5180 *6906
nOTE: * exceeds tensile strength of the screw.Tested values are available upon request.
F
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD4.0616
Sliding Rake Angle Screw SSR Clip | 5/16" HWH
• Drill and tap up to 1/2” thick steel.• Supplied with our TRI-SEAL® long life coating for
superior corrosion protection.• Lengths up to 8” for retrofit metal roof base attachment.
Heavy Gauge Applications | 1/4” to 1/2” BLAZER 4 & BLAZER 5 Points
● The hex washer head is the most popular drive system and provides the best stability during installation.
● Available with TRI-SEAL® long life coating for the ultimate corrosion protection...1,000 hrs salt spray with no red rust!A
B
C
MATERIAL: C1018-1022 Carbon SteelPLATING: .0003" Minimum Zinc Plated (48 hrs salt-spray)Long-Life: TRI-SEAL® Coating (1,000hrs Salt Spray - ASTM B117). Exceeds ASTM B633 and F1941 Standards Dimensions: Meets or exceeds SAE J78 Standards
H
I
J
D
E
F
G
*High Hex or Serrations Available
HEX DRIVE SIZE #8 dia: 1/4" HWH
#10 dia: 5/16" HWH #12 dia: 5/16" HWH
1/4 dia: 5/16” & 3/8" HWH 5/16 dia: 3/8" HWH
DRILL SCREWSBLAZER R HEX WASHER HEAD
BLAZER® SELF-DRILLING TAPPING SCREWS
SIZES AND PERFORMANCE SPECIFICATIONS
Blue colored sizes denotes popular DC
items
*Available in 5/16" and 3/8" HWH
Diameter | Length
Attachment Thickness
(Max)Box Qty
Point Type
Drilling Thickness
A #8-18 x
1/2" .100" 10M
BLAZER2
.036”
.100”
5/8" .125" 10M
3/4" .250" 10M
1" .500" 7.5M
1-1/4" .750" 5M
1-1/2" 1" 5M
2" 1.5" 1.5M
B #10-16 x
1/2" .100" 10M
BLAZER3
.036”
.175”
5/8" .125" 5M5/8" HH/SERR .125" 5M3/4" .250" 5M3/4" HH .250" 5M1" .500" 5M1-1/2" 1" 3.5M2" 1.500" 2M3" 2.500" 1M
C #12-14 x
3/4" .125" 5M
BLAZER2
.036"
.210"
1" .250" 3.5M1-1/4" .625" 3M1-1/2" .750" 2M2" 1.25" 2M2-1/2" 1.75" 1M3" 2.75" 1M
D 1/4-14 x 7/8" VRT .325" 2.5M BLAZER 1/VRT
.036"
.090"
E 1/4-14 x
3/4" .125" 2.5M
BLAZER3
.036"
.250"
1" .250" 2.5M1-1/4" .625" 2M1-1/2" .875" 2M2" 1" 1.5M2-1/2" 1.50" 1M3" 2" 1M4" 3" 5005" 4" 5006" 2" - 5" 2508" 4" - 7" 25010" 6" - 9" 250
F 1/4-14 x 1-1/4" .750" 3.5MBLAZER
3SHLDR
G 5/16-12 x
1" .250" 1.5M
BLAZER3
.036"
.210"
1-1/2" .875" 1M3" 2.25" 7504" 3.25" 5006" 2.50 - 5" 5008" 4.25" - 7" 200
H #12-24 x7/8" .325" 5M BLAZER
4.125".250"
1-1/4” .500” 3M BLAZER4.5
.125”
.375”
I #12-24 x1-1/4" .500" 3M
BLAZER 5
.125"
.500"1-1/2" .625" 2M2" .750" 3M
J 1/4-20 x
1-1/2" .500" 2M
BLAZER5
.200"
.500"
2-1/4" 1.250" 1M3" 2" 5004" 3" 2505" 4" 2506" 2.50" - 5" 2508" 4.25" - 7" 150
Want a screw that takes more force before bending?Our NEW 5/16" diameter is 5-1/2 times stiffer than a 1/4-14 drill screw.
The largest selection for the construction industry!
5/16" HWH
All screws are available with Bonded Sealing Washers.Call for sizes
Thin and Medium Gauge Applications | 29ga to 1/4” BLAZER 1 - BLAZER 2 - BLAZER 3 Points
9
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD16.0616
● BOND-SEALER™ is a sealing washer that has EPDM vulcanized to a 20 Gauge galvanized backing that will withstand harsh weather conditions.
● TRI-SEAL® long life coated for superior corrosion protection.
WASHER DETAILS20 ga G-90 Galvanized Steel Vulcanized to .062” thick non-conductive EPDM15MM OD Washer
Special sizes available upon request.
CORRECTSlight circle of sealant ex-
trudes to outer edge.
TOO TIGHT!Metal backing
begins to turn up.
TOO LOOSESealant is not compressed and can not form a seal.
To assure a proper seal, torque the fastener until the EPDM sealant extrudes to the outer edge of the backing material.
Proper Fastener Installation
● FLANGE-SEAL™ self-sealing fastener has a deep undercut head that entraps the EPDM sealing washer to assure a leak free seal.
● TRI-SEAL® long-life coated for superior corrosion protection.
WASHER DETAILS.125” Thick EPDMNon-conductive
A
B
C
D
E
F
G
H
I
HEAD TYPE #12 dia: 5/16" HWH1/4” Dia: 3/8” HWH *1/4 dia: 5/16” & 3/8"HWH 5/16 dia: 3/8" HWH
FLANGE-SEAL HEAD with EPDM WASHER
SIZES AND PERFORMANCE SPECIFICATIONS
SIZES AND PERFORMANCE SPECIFICATIONS
HEAD TYPE 5/16" HWH with Flange Undercut
Blue colored sizes denotes popular DC
items
Blue colored sizes denotes popular DC
itemsDiameter | Length
Attachment Thickness
(Max)Box Qty
Point Type
Drilling Thickness
G #12-14 x
1" .250" 3.5MBLAZER
2/3.036”.210”
1-1/4" .500" 3M1-1/2" .750" 2M2" 1" 2M
H 1/4-14 x 7/8" VRT .325" 2.5M BLAZER1/VRT
.036"
.090"
I 1/4-14 x
1" .250" 2.5MBLAZER
3.036”.250”
1-1/4" .500" 2.5M1-1/2" .750" 2M2” 1.25” 1.5m
DRILL SCREWSBLAZER R BLAZER® SELF-DRILLING TAPPING SCREWS
With Sealing Washers
Diameter | Length
Attachment Thickness
(Max)Box Qty
Point Type
Drilling Thickness
A #12-14 x
3/4" .125" 5M
BLAZER2
.036"
.210"
1" .250" 3.5M1-1/4" .625" 3M1-1/2" .750" 2M2" 1.25" 2M2-1/2" 1.75" 1M3" 2.75" 1M
B 1/4-14 x *7/8" VRT .325" 2.5M BLAZER 1/VRT
.036"
.090"
C 1/4-14 x
3/4" .125" 2.5M
BLAZER3
.036"
.250"
*1" .250" 2.5M*1-1/4" .625" 2M1-1/2" .875" 2M2" 1" 1.5M2-1/2" 1.50" 1M3" 2" 1M4" 3" 5005" 4" 5006" 2" - 5" 2508" 4" - 7" 25010" 6" - 9" 250
D 5/16-12 x
1" .250" 1.5M
BLAZER3
.036"
.210"
1-1/2" .875" 1M3" 2.25" 7504" 3.25" 5006" 2.50 - 5" 5008" 4.25" - 7" 200
E #12-24 x1-1/4" .500" 3M
BLAZER 5
.125"
.500"1-1/2" .625" 2M2" .750" 3M
F 1/4-20 x
1-1/2" .500" 2M
BLAZER5
.200"
.500"
2-1/4" 1.250" 1M3" 2" 5004" 3" 2505" 4" 2506" 2.50" - 5" 2508" 4.25" - 7" 150
The largest selection for the construction industry!
MATERIAL: C1018-1022 Carbon SteelPLATING: TRI-SEAL® Coating (1,000hrs Salt Spray - ASTM B117). Exceeds ASTM B633 and F1941 Standards Dimensions: Meets or exceeds SAE J78 Standards
MATERIAL: C1018-1022 Carbon SteelPLATING: TRI-SEAL® Coating (1,000hrs Salt Spray - ASTM B117). Exceeds ASTM B633 and F1941 Standards Dimensions: Meets or exceeds SAE J78 Standards
BOND-SEAL SEALING WASHER
10
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD5.0616
1/4” and 5/16” DIAMETERS LENGTHS UP TO 10" LONG
We stock a full line of 1/4" and 5/16" BLAZER® drill screws for drilling and tapping up to 1/2” thick steel.
BLAZER® self-drilling screws are engineered to drill and tap high tensile steels more consistently with less effort.
SIZES AND PERFORMANCE SPECIFICATIONS
DISCLAIMER: ALL TESTS RESULTS AND SPECIFICATIONS ARE A RESULT OF LABORATORY TESTS. APPROPRIATE SAFETY FACTORS SHOULD BE USED BY THE USER OR SPECIFIER. DETERMINING THE PROPER FASTENER IS THE RESPONSIBILITY OF THE USER OR SPECIFIER. SINCE APPLICATION CONDITIONS VARY AND ARE UNCONTROLLABLE BY TFC, WE ASSUME NO LIABILITY FOR THE USE OF THIS INFORMATION.
Rev. CW1115
Blue colored sizes denotes popular DC
items
Diameter | LengthAttachment Thickness
Box Qty
Point Type
Drilling Thickness
1/4-14 x
1" .250" 2.5M
BLAZER3
.036"
.250"
1-1/4" .625" 2M1-1/2" .875" 2M2" 1" 1.5M3" 2" 1M4" 3" 5005" 4" 5006" 2" - 5" 2508" 4" - 7" 25010" 6" - 9" 250
5/16-12 x
1" .250" 2M
BLAZER 3
.036"
.210"
1-1/2" .875" 1.5M3" 2.25" 7504" 3.25" 4006" 2.50 - 5" 2008" 4.25" - 7" 200
1/4-20 x
1-1/2" .500" 2M
BLAZER5
.200"
.500"
2-1/4" 1.250" 1M3" 2" 5004" 3" 2505" 4" 2506" 2.50" - 5" 2508" 4.25" - 7" 150
Concerned about bending?Our 5/16" diameter BLAZER provides additional stiffness to the connection.
1/4-14 DP3• Drill and Tap to .250" Steel• Lengths up to 10"• 3/8" HWH• TRI-SEAL® 1,000 hrs
Salt Spray Coated
1/4-20 DP5• Drill and Tap to .500" Steel• Lengths up to 8"• 3/8" HWH• 5/8" O.D. Washer Face• TRI-SEAL ® 1,000 hrs
Salt Spray Coated
5/16-12 DP3• Add more stiffness
to your connection• Drill and Tap to .210" Steel• Lengths up to 8"• 3/8" HWH• 5/8" O.D. Washer Face• TRI-SEAL® 1,000 hrs
Salt Spray Coated
Fastener Diameter
Nominal Screw Diameter
Major Diameter (inch)
Minor Diameter (inch)
Tensile Stress Area (sq in.)
Torsional (lb-In)
Tensile(Pounds)
Shear(Pounds)
Max Min Max Min1/4-14 0.250 0.246 0.240 0.192 0.185 0.0269 150 3,497 2,0981/4-20 0.250 0.250 0.242 0.218 0.214 0.0360 156 4,680 2,808
5/16-12 0.313 0.315 0.306 0.244 0.236 0.0418 290 5,439 3,264
TECHNICAL DATA
FastenerSize
PULLOUT | ALLOWABLE | Grade 50/55 Steel 65Ksi Calculated Values In Accordance to AISI S100 | Section E4
Applied Factor of Safety = 3
18 Ga.(.048")
16 Ga.(.060")
14 Ga.(.075")
12 Ga.(.105")
1/8"(.125")
10 ga(.135")
1/4"(.250")
3/8"(.375")
1/2"(.500")
1/4-14 DP3 221.0 276.2 345.3 483.4 575.5 621.6 1,151.0
1/4-20 DP5 621.6 1,151.0 1,726.5 2,302.1
5/16-12 DP3 276.2 345.3 431.6 604.3 719.4 776.9
All sizes are available with BOND-SEAL™ Sealing Washers.
DRILL SCREWSBLAZER R
TOOLING: Install using a 2,000 RPM screw-gun with torque control (DeWalt DW267). Do not use impact tools.
The largest selection of self-drilling screws specifically designed for increase strength
11
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD8.0616
• Provides corrosion resistance in mild atmospheres.• Plated to resist surface rust and to reduce tapping torque.• Optional TRI-SEAL® 1,000 hrs salt spray long-life coated to
reduce tapping torque and provide additional corrosion protection.
MATERIAL: 410 Stainless SteelPLATING: Passivated (24hrs Salt Spray), Zinc Plated (48hrs Salt Spray), TRI-SEAL® Coated (1,000hrs Salt Spray). Call for sizes
A
B
C
D
E
F
SIZE HEAD TYPE #8 1/4" HWH #10, #12, *1/4" 5/16" HWH 1/4" 3/8 "HWH
HIGH PERFORMANCE SELF-DRILLING SCREWS FOR COMMERCIAL CONSTRUCTION
BLAZER SELF-DRILLING SCREWS410 Stainless Steel
SIZES AND PERFORMANCE SPECIFICATIONS
Blue colored sizes denotes popular DC
items
Diameter | LengthAttachment Thickness
Box Qty
Point Type
Drilling Thickness
A #8-18 x1/2" .100" 10M BLAZER
2 .036" - .100"3/4" .125" 10M
B #10-16 x
3/4" .125" 7.5MBLAZER
3 .036" - .175"1" .500" 5M
1-1/2" 1" 5M
C #12-14 x
3/4" .125" 5M
BLAZER2/3 .036" - .210"
1" .500" 3.5M
1-1/4" LP .750" 3M
1-1/2" 1" 2M
2" 1.250" 2M
2-1/2" 1.750"
3" 2.250"
D 1/4-14 x7/8" .325" 2.5M BLAZER
1/VRT .036" - 090"1-1/8" .875" 2.0M
E 1/4-14 x
3/4" .125" 2.5M
BLAZER3 .036" - .250"
1" .250" 2.5M
1-1/4" .500" 2M
1-1/2" .750" 2M
2" 1" 1.5M
3" 2" 1.5M
4" 3" 500
5" 4" 500
F #12-24 x1-1/4" .500" 5M BLAZER
5 .125" - .500"1-1/2" .625" 3.5M
All screws are available with Bonded Sealing Washers.Call for sizes
DRILL SCREWSBLAZER R
Fastener Information
PULLOUT | ULTIMATE LOAD IN POUNDSGrade 80 and Grade 50 Steel per ASTM A792/A1011/A653/A572/A529
Calculated Values In Accordance to AISI S100 | Section E4
Thread and Point Type
Nom Dia.(in.)
Grade 8082Ksi Min.
Grade 5065Ksi Min. Steel
26 Ga.(.018")
24 Ga.(.024")
22 Ga.(.030")
20 Ga.(.036")
18 Ga.(.048")
16 Ga.(.060")
14 Ga.(.075")
12 Ga.(.105")
1/8"(.125")
10 ga(.135")
1/4"(.250")
3/8"(.375")
1/2"(.500")
#8-18 .164" 156 218 272 326 435 543
#10-16 .190" 180 252 315 378 504 627 786 1,101 1,311
#12-14 .216" 205 286 358 430 573 716 895 1,253 1,492 1,611
#12-24 .216" 1,492 1,611 2,984 *4,475 *5,967
1/4-14 .250" 237 332 414 497 633 829 1,036 1,450 1,727 1,865 3,453
For allowable loads, please apply an appropriate Factor of Safety as required by local and national code requirements.
AISI S100 Section E4 recommends a Factor of Safety of 3 for allowable loads
DISCLAIMER: ALL TEST RESULTS AND SPECIFICATIONS ARE A RESULT OF LABORATORY TESTS. APPROPRIATE SAFETY FACTORS SHOULD BE USED BY THE USER OR SPECIFIER. DETERMINING THE PROPER FASTENER IS THE RESPONSIBILITY OF THE USER OR SPECIFIER. SINCE APPLICATION CONDITIONS VARY AND ARE UNCONTROLLABLE BY TFC, WE ASSUME NO LIABILITY FOR THE USE OF THIS INFORMATION.
Pullout Loads | Ultimate in Pounds ForceCarbon Steel and 410 Stainless Steel ScrewsThe tensile strength of the substrate that is used in the chart below is typical for metal building and roofing applications. Contact TFC if other substrate tensile strengths are required.
12
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD9.0616
BLAZER SELF-DRLLING SCREWSWOOD-TO-METAL APPLICATIONS
Need to attach wood to metal thinner than 1/4"? Our full line of sizes are designed to fasten to metal as thin as 18-gauge!
Need to attach wood to steel that is 1/2” thick?We offer the only wood-to-metal fastener that will drill and tap steel up to 1/2” thick. It has a special hex-countersunk head that provides optimal driving stability and can also be installed flush to the surface of the wood.
DISCLAIMER: ALL TESTS RESULTS AND SPECIFICATIONS ARE A RESULT OF LABORATORY TESTS. APPROPRIATE SAFETY FACTORS SHOULD BE USED BY THE USER OR SPECIFIER. DETERMINING THE PROPER FASTENER IS THE RESPONSIBILITY OF THE USER OR SPECIFIER. SINCE APPLICATION CONDITIONS VARY AND ARE UNCONTROLLABLE BY TFC, WE ASSUME NO LIABILITY FOR THE USE OF THIS INFORMATION.
SIZES
Recommended Screw Gun Speed: 2,000 RPM Max
Square recess for superior stability during installation.
A
B
C
Head Type #10: #2 Sq - Wafer Countersunk #12: #3 Sq - Wafer Countersunk1/4": 5/16” Hex CountersunkMaterial: C-1022 Carbon steelFinish: TRI-SEAL® Long-life Salt Spray: 1,000hrsCompatible for use in ACQ and fire treated lumber.Produced to SAE J78 specifications.
TECHNICAL DATA
We have the largest selection of wood-to-metal drill screws engineered to provide high performance and easy installation.
DRILL SCREWSBLAZER R
WOOD THICKNESS
DRILLING THICKNESS Screw Diameter | Length | Point
Box Qty
1/2" to 3/4"
.048" - .210" A #10-24 x 1-7/16" BLAZER-3 With Wings 4M
.018" - .175" B #10-16 x 1-3/4" BLAZER-3 Long Pilot 2.5m
.048" - .210" C #12-14 x 1-3/4" BLAZER-2 With Wings 2M
.210" - .500" D *#12-24 x 2" BLAZER-5 With Wings 2M
3/4" to 1-1/2".048" - .210" E #12-14 x 2-1/2" BLAZER-2 With Wings 1M.210" - .500" F 1/4-20 x 3-1/8" BLAZER-5 With Wings 1M
D
E
F
Fastener Information
PULLOUT | ULTIMATE LOAD IN POUNDSGrade 80 and Grade 50 Steel per ASTM A792/A1011/A653/A572/A529
Calculated Values In Accordance to AISI S100 | Section E4
Thread and Point Type
Nom Dia.(in.)
Grade 8082Ksi Min.
Grade 5065Ksi Min. Steel
26 Ga.(.018")
24 Ga.(.024")
22 Ga.(.030")
20 Ga.(.036")
18 Ga.(.048")
16 Ga.(.060")
14 Ga.(.075")
12 Ga.(.105")
1/8"(.125")
10 ga(.135")
1/4"(.250")
3/8"(.375")
1/2"(.500")
#10 BLAZER-2 .190" 180 252 315 378 504 627 786 1,101 1,311
#12 BLAZER-2 .216" 205 286 358 430 573 716 895 1,253 1,492 1,611
#12 BLAZER-5 .216" 1,492 1,611 2,984 *4,475 *5,967
1/4 BLAZER-5 .250" 1,727 1,865 3,453 *5,180 *6,906
Select a screw based on the thickness of the wood and the thickness of the steel substrate.
Screw RecommendationsSteel <= .210" : Screw A, B, C
Steel > .210" : Screw D
Screw RecommendationsSteel <= .210" : Screw ESteel > .210" : Screw F
5/16 hex countersunk head provides exceptional stability during installation and can be installed flush to the wood surface.
#2 Sq
#2 Sq
#3 Sq
#3 Sq
#3 Sq
1/2" to 3/4" WOOD 1" to 1-5/8" WOOD
*New size available in September 2016
13
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD17.0616
SpecificationsWasher: .100” Thick EPDM. Non-conductiveHead Type: 5/16" HWHMaterial: HEAD - 304 Stainless Steel; BODY - Carbon SteelPlating: HEAD - Passivated; BODY - TRI-SEAL® Long-life CoatingCorrosion: HEAD- >2,000hrs Salt Spray; BODY - 1,000hrs Salt Spray
LP denotes long-pilot design for metal roofing and siding
Size & PointDrilling
ThicknessAttachment Thickness
Box Qty
A
#12-14 x 1" BLAZER 2/3 #12-14 x 1-1/4" BLAZER 2/3 LP#12-14 x 1-1/2" BLAZER 2/3 #12-14 x 2" BLAZER 2/3
.036" - .210"
.250"
.500"
.750"1"
3.5M2.5M2.5M2M
B1/4-14 x 7/8" BLAZER 1/VRT1/4-14 x 1-1/8" BLAZER 1/VRT .018" -.090"
.250"
.750"2.5M2M
C1/4-14 x 1-1/4" BLAZER 3 1/4-14 x 3" BLAZER 31/4-14 x 4" BLAZER 3
.036" - .250".250"
2"3"
2M 500500
D #17-14 x 1" TYPE AB W/VRT 20ga or less .750" 2.5M
E#12-24 x 1-1/4" BLAZER 5 #12-24 x 2" BLAZER 5 .250" - .500"
.500"
.625"2.5M 2.5M
F#12-14 | 1/4-14 x 1-7/8" BLAZER 3 #12-14 | 1/4-14 x 2-3/8" BLAZER 3 #12-14 | 1/4-14 x 3-1/4" BLAZER 3 #12-14 | 1/4-14 x 4" BLAZER 3
.036"-.210"
.875"-1.125"1.125"-1.625"1.750"-2.437"2.500"-3.187"
2M 1M 1M 500
A
B
C
D
E
F
BLAZER® STAINLESS CAP HEAD WITH EPDM SEALING WASHER
• ZAMAC 5 zinc alloy cap head for premiumcorrosion resistance WILL NOT RED RUST!
• TRI-SEAL® long life coated shank forsuperior corrosion protection.
SpecificationsMaterial: HEAD - Zamac 5 Zinc Alloy; THREAD - Carbon SteelPlating: BODY - TRI-SEAL® Long-life Coating.Corrosion Resistance: HEAD - No Red Rust; BODY - 1,000hrs Salt Spray
LP denotes long-pilot design for metal roofing and siding
HEAD TYPE 5/16" HWH
BLAZER® ZINC CAP HEAD WITH EPDM SEALING WASHER
BLAZER® SELF-DRILLING SCREWS Stainless Cap and Zinc Cap Heads
SIZES AND PERFORMANCE SPECIFICATIONS
SIZES AND PERFORMANCE SPECIFICATIONSBlue colored
sizes denotes popular DC
items
DRILL SCREWSBLAZER R
G
H
I
J
K
L
Blue colored sizes denotes popular DC
items
Need a 3/8” Hex Washer Head? Contact us for available sizes.
• 304 stainless steel cap head for exceptional corrosion resistance.• TRI-SEAL® long life coated shank for superior corrosion protection.
WASHER DETAILS .125” Thick EPDM.
Non-conductive
Size & PointDrilling
ThicknessAttachment Thickness
Box Qty
G
#12-14 x 1" BLAZER 2/3 #12-14 x 1-1/4" BLAZER 2/3 LP#12-14 x 1-1/2" BLAZER 2/3 #12-14 x 2" BLAZER 2/3
.036" - .210"
.250"
.500"
.750"1"
3.5M2.5M2.5M2M
H1/4-14 x 7/8" BLAZER 1/VRT1/4-14 x 1-1/8" BLAZER 1/VRT .018" -.090"
.250"
.750"2.5M2M
I1/4-14 x 1-1/4" BLAZER 3 1/4-14 x 3" BLAZER 31/4-14 x 4" BLAZER 3
.036" - .250".250"
2"3"
2M 500500
J #17-14 x 1" TYPE AB W/VRT 20ga or less .750" 2.5M
K#12-24 x 1-1/4" BLAZER 5 #12-24 x 2" BLAZER 5 .250" - .500"
.500"
.625"2.5M 2.5M
L#12-14 | 1/4-14 x 1-7/8" BLAZER 3 #12-14 | 1/4-14 x 2-3/8" BLAZER 3 #12-14 | 1/4-14 x 3-1/4" BLAZER 3 #12-14 | 1/4-14 x 4" BLAZER 3
.036"-.210"
.875"-1.125"1.125"-1.625"1.750"-2.437"2.500"-3.187"
2M 1M 1M 500
14
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD14.0616
BACK-OUT RESISTANT SCREWS
Standard Thread
VRTThread
You can see how the shape of VRT® is designed to increase the resistance to back-out compared to a standard thread. VRT® keeps the fastener tighter in applications where expansion, contraction and vibration are a concern.
Why VRT™?
Notice how standard screw threads offer little resistance to back-out.
Our Vibration Resistant Thread (VRT) is designed to significantly increase back-out torque and reduce the potential for leaks.
Innovative patented VRT® thread increases friction as the screw loosens.
Screws with standard threads can back-out easily with little force. This can cause joint failure resulting in leaks.
PROBLEM SOLUTION
Independent tests verify that VRT produces over 3-1/2 times more back-out resistance than standard threads due to it’s innovative thread design that increases friction.
Over 250% More
Torque!
LEAKZONE
Test Results
(Installed torque = 40 in-lb)
Form # JS100808Copyright 2008 Triangle Fastener Corporation
Our Vibration Resistant Thread (VRT®) is designed to significantly increase back-out torque and reduce the potential for leaks. VRT® keeps the fastener tighter in applications where expansion, contraction and vibration are a concern. Independent tests verify that VRT® produces 3-1/2 times more back-out resistance than a standard thread.
US Pat. No. 8,360,701Other Worldwide Patents
15
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD15.0616
Description Part NumberCarton
QuantityWT Per M Pcs
1/4” -14 X 7/8” DP1/LAP w/VRT® CONCEALOR® Pancake Headw/Bonded Sealing WasherTRI-SEAL™ Coated1,000Hrs Salt Spray
14087C1TSVBW 2,500 pcs250/Bag 13.5#
1/4” -14 X 7/8” DP1/LAP w/VRT®
BLAZER® Flange Head w/Sealing WasherTRI-SEAL™ Coated1,000Hrs Salt Spray
14087HW1CSTSVW 2,500 pcs 250/Bag 13.5#
1/4” -14 X 7/8” DP1/LAP w/VRT® BLAZER®
TRI-SEAL™ Coated1,000Hrs Salt Spray
14087HW1CSTSV 2,500 pcs 250/Bag 10.2#
1/4” -14 X 7/8” DP1/LAP w/VRT® BLAZER® w/Bonded Sealing WasherTRI-SEAL™ Coated1,000Hrs Salt Spray
14087HW1CSTSVBW 2,500 pcs 250/Bag 13.5#
1/4” -14 X 7/8” DP1/LAP w/VRT® BLAZER® Stainless Cap Headw/Sealing WasherTRI-SEAL™ Coated1,000Hrs Salt Spray
14087HW1CSTSVWSC 2,500 pcs250/Bag 13.5#
1/4” -14 X 7/8” DP1/LAP w/VRT®
BLAZER® Zinc Cap Headw/Sealing WasherTRI-SEAL™ Coated1,000Hrs Salt Spray
14087HW1CSTSVWZC 2,000 pcs250/Bag 13.5#
1/4” -14 X 1-1/8” DP1/LAP w/VRT® BLAZER® Stainless Cap Head w/Sealing WasherTRI-SEAL™ Coated1,000Hrs Salt Spray
14112HW1CSTSVWSC 2,000 pcs250/Bag 19.3#
#17-14 X 1” TYPE AB w/VRT® TAP-PERw/Bonded Sealing Washer (3/4”OD)TRI-SEAL™ Coated1,000Hrs Salt Spray
17100HHACSTSVOW 2,000 pcs250/Bag 20#
SpecificationsBLAZER Drill Screws conforms to SAE J-78 for self-drilling tapping screws.
#17 TAPPER conforms to ANSI/ASME B18.6.4 for tapping screws.
Material Carbon Steel: C1022 Stainless Cap: 304 SS Zinc Cap: Zamac 5
Tensile Strength 1/4-14: 4,275 lbs. #17-14: 5,200 lbs.
Torsional Strength 1/4-14: 150 lbs-inch #17-14: 175 lbs-inch
Corrosion ResistanceTRI-SEALSalt Spray: 1,000 hrs minimum.
Sealing WashersFlange Head: EPDM Cut Tubular
Bonded Washer EPDM Vulcanized to G-90 Galvanized Steel. (15MM O.D.).
Sizes and Technical Data Sheet
Our Vibration Resistant Thread (VRT®) is designed to significantly increase back-out torque and reduce the potential for leaks.VRT® keeps the fastener tighter in applications where expansion, contraction and vibration are a concern.Independent tests verify that VRT® produces 3 -1/2 times more back-out resistance than a standard thread.
Light Gauge ApplicationsMaximum Drilling Thickness: .090” Technical Data
BACK-OUT RESISTANT SCREWSPat. No. 8,360,701
16
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD13.0616
BLAZER® SECURITY SCREWS
Security screws specifically designed for metal siding and roofing applications
TORX® PIN-HEADMaximum torque transfer and positive tool engagement means easier drive installation with less pressure and slippage. Torx® Pin Head offers a high degree of security and requires matching drive bit. Available in button head for neat appearance and TRI-SEAL™ 1,000 hours salt spray coating for additional corrosion protection.
Contact Triangle Fastener for additional sizes and types of security screws.
Does your building need security? � Mini Storage � Prisons � Government Buildings � Banks � Dealerships
Assembled with a BOND-SEALER™ sealing washer that has EPDM vulcanized to a 20 Gauge galvanized backing that will withstand harsh weather conditions.
MATERIAL: C1018-1022 Carbon SteelPLATING: .TRI-SEAL™ 1,000 hours salt spray coating
CORRECTSlight circle of sealant
extrudes to outer edge.
TOO TIGHT!Metal backing
begins to turn up.
TOO LOOSESealant is not compressed and can not form a seal.
To assure a proper seal, torque the fastener until the EPDM sealant extrudes to the outer edge of the backing material.
SizePoint Type
Drilling Thickness
Attachment Thickness
Box Quantity
A #12-14 x 2BLAZER 3
.036" - .210" 1" 2.0M
B #12-14 x 1-1/2" .036" - .210" .750" 2.0M
C 1/4-14 x 7/8" BLAZER 1 .036" - .090" .250" 2.5M
We supply insert bits to make installation fast and easy!
DISCLAIMER: ALL TEST RESULTS AND SPECIFICATIONS ARE A RESULT OF LABORATORY TESTS. APPROPRIATE SAFETY FACTORS SHOULD BE USED BY THE USER OR SPECIFIER. DETERMINING THE PROPER FASTENER IS THE RESPONSIBILITY OF THE USER OR SPECIFIER. SINCE APPLICATION CONDITIONS VARY AND ARE UNCONTROLLABLE BY TFC, WE ASSUME NO LIABILITY FOR THE USE OF THIS INFORMATION.
Pullout Test Result - Ultimate Average in Pounds
T-27 Torx Pin Recess Drive
SIZES AND PERFORMANCE SPECIFICATIONS
A
B
C
Blue colored sizes denotes popular DC
items
DRILL SCREWSBLAZER R
The tensile strength of the substrate that is used in the chart is typical for metal building and roofing applications. Contact TFC if other substrate tensile strengths are required.
Fastener Information
PULLOUT | ULTIMATE LOAD IN POUNDSGrade 80 and Grade 50 Steel per ASTM A792/A1011/A653/A572/A529
Calculated Values In Accordance to AISI S100 | Section E4
Thread and Point Type
Nom Dia.(in.)
Grade 8082Ksi Min.
Grade 5065Ksi Min. Steel
26 Ga.(.018")
24 Ga.(.024")
22 Ga.(.030")
20 Ga.(.036")
18 Ga.(.048")
16 Ga.(.060")
14 Ga.(.075")
12 Ga.(.105")
1/8"(.125")
10 ga(.135")
1/4"(.250")
3/8"(.375")
1/2"(.500")
#12-14 .216" 205 286 358 430 573 716 895 1,253 1,492 1,611
1/4-14 .250" 237 332 414 497 633 829 1,036 1,450
17
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD6.0616
RAKE ANGLE ATTACHMENT SCREW
We designed a BLAZER® Drill Screw specifically for attaching a sliding rake plate used in metal roofing.
The screw has an oversize washer face that provides more bearing surface between the fastener and the rake plate angle that allows superior movement capabilities.
Proprietary standoff screw designed to allow thermal expansion of the rake support angle
SIZE
Pullout Test Results
Size
GAGE THICKNESS & ULTIMATE PULLOVER IN POUNDS (55 KSI STEEL)
26 Ga.(.018")
24 GA.(.024")
22 Ga.(.030")
20 Ga.(.036")
18 Ga.(.046")
1/4-14 DP3 928 1,238 1,547 1,856 2,475
Note: Estimated pullover for fasteners without sealing washers can be calculated using the following formula per AISI. Pullover force = 1.5 X Thickness of the member in contact with the screw head. X Larger of the screw head diameter or washer diameter. X Tensile strength of the member in contact with the screw head.
DISCLAIMER: ALL TESTS RESULTS AND SPECIFICATIONS ARE A RESULT OF LABORATORY TESTS. APPROPRIATE SAFETY FACTORS SHOULD BE USED BY THE USER OR SPECIFIER. DETERMINING THE PROPER FASTENER IS THE RESPONSIBILITY OF THE USER OR SPECIFIER. SINCE APPLICATION CONDITIONS VARY AND ARE UNCONTROLLABLE BY TFC, WE ASSUME NO LIABILITY FOR THE USE OF THIS INFORMATION.
Size
Nominal Screw
Diameter
Major Diameter (In.) Minor Diameter (In.) Area of Minor Diameter (Sq. In.)Max Min Max Min
1/4-14 BLAZER 3 0.250 0.250 0.242 0.218 0.214 0.0360
Pullover Test Results
Physical Properties
SizeTorsional(lbs-Inch)
Tensile (Lbs.)
Shear(Lbs.)
1/4-14 DP3 150 4,275 2,600
Performance Specifications
TECHNICAL DATA
TYPICAL APPLICATION
Oversize washer face provides over 45% more surface area that is in contact with the rake support!
Special shoulder keeps screw from “over-clamping” the rake support, allowing for thermal expansion.
5/16” hex drive is the same size as other standard metal roofing fasteners for easy installation.
SizePoint Type
Head Size
Attachment Thickness
Box Quantity
1/4-14 x 1-1/4” DP3 5/16” HWH
.150” standoff 2,000
Finish: JS500 | Zinc Plating.Salt Spray 400 hours | No red rust per ASTM B117
DRILL SCREWSBLAZER R
FastenerSize
PULLOUT | ALLOWABLE | Grade 50/55 Steel 65Ksi Calculated Values In Accordance to AISI S100 | Section E4
Applied Factor of Safety = 3
18 Ga.(.048")
16 Ga.(.060")
14 Ga.(.075")
12 Ga.(.105")
1/8"(.125")
10 ga(.135")
1/4"(.250")
1/4-14BLAZER 3 221.0 276.2 345.3 483.4 575.5 621.6 1,151.0
18
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD18.0616
BLAZER® self-drilling fasteners are produced and perform to SAEJ78, ASME/ANSI 18.18. and AISI TS-4-02 specifications. Conforms to ICCESAC18 acceptance criteria for tapping screw fasteners.
The following information is compiled to assist the design professional in selecting the appropriate fastener for the application. This data is compiled from fastener standards and independent tests. An engineering professional should be consulted to determine expected loads on the connection, environmental effects, and any other conditions that could effect the performance of the fastener. Selecting a fastener is the responsibility of the engineer and changes to a fastener should not be made without approval. Using the wrong fastener can lead to failure. TFC WILL NOT WARRANTY, EITHER EXPRESSED OR IMPLIED,THE USE OF THIS INFORMATION.
TorsionalThread Description Tensile
DISCLAIMER: ALL TEST RESULTS AND SPECIFICATIONS ARE A RESULT OF LABORATORY TESTS. APPROPRIATE SAFETY FACTORS SHOULD BE USED BY THE USER OR SPECIFIER. DETERMINING THE PROPER FASTENER IS THE RESPONSIBILITY OF THE USER OR SPECIFIER. SINCE APPLICATION CONDITIONS VARY AND ARE UNCONTROLLABLE BY TFC, WE ASSUME NO LIABILITY FOR THE USE OF THIS INFORMATION.
Pounds - Ultimate Average
These pullover results are for self-sealing fasteners listed in this catalog.
Note: Estimated pullover for fasteners without sealing washers can be calculated using the following formula per AISI.
Pullover force = 1.5 -x- Thickness of the member in contact with the screw head. -x- Larger of the screw head diameter or washer diameter. -x- Tensile strength of the member in contact with the screw head.
Fastener Diameter
Nominal Screw Diameter
Major Diameter (inch)
Minor Diameter (inch)
Area Of Minor Dia. (sq in.)
Torsional (Lb-In.)
Tensile(Pounds)
Shear(Pounds)
Max Min Max Min#6-20 0.138 0.139 0.135 0.104 0.099 0.0077 25 1,125 750#8-18 0.164 0.166 0.161 0.122 0.116 0.0106 42 1,575 1,000
#10-16 0.190 0.189 0.183 0.141 0.135 0.0143 61 2,100 1,400#10-24 0.190 0.190 0.182 0.144 0.137 0.0147 65 3,400 2,275#12-14 0.216 0.215 0.209 0.164 0.157 0.0194 92 2,778 2,000#12-24 0.216 0.216 0.209 0.189 0.185 0.0269 100 3,188 2,1001/4-14 0.250 0.246 0.240 0.192 0.185 0.0269 150 3,850 2,6001/4-20 0.250 0.250 0.242 0.218 0.214 0.0360 156 4,275 2,700#18-9 0.306 0.306 0.300 0.217 0.209 0.0343 170 4,550 2,576
5/16-12 0.313 0.315 0.306 0.244 0.236 0.0702 290 5,439 3,264
English to Metric Formula to Use
Decimal to Millimeters Decimal x 25.4
PSI to Newton / Millimeters² PSI x .007
Pounds Force to Newtons Pounds Force x 4.448
Gauge Thickness Decimal Metric
29 GA .013" .33mm
28 GA .015" .38mm
26 GA .018" .46mm
24 GA .024" .61mm
22 GA .030" .76mm
20 GA .036" .91mm
18 GA .048" 1.22mm
16 GA .060" 1.52mm
14 GA .075" 1.91mm
12 GA .105" 2.67mm
1/8" .125" 3.18mm
10 GA .135" 3.43mm
1/4" .250" 6.35mm
5/16" .312" 7.92mm
3/8" .375" 9.53mm
1/2" .500" 12.7mmSteel
ThicknessBOND-SEALER FLANGE
SEALERZINC
CAP HEADSTAINLESSCAP HEAD12.7MM OD 15MM OD
22 ga 945 1,249 1,298 1,647 1,29824 ga 704 1,056 1,102 1,310 1,10226 ga 519 654 692 794 692
Material: C1018-C1022 / 410 SSHeat Treatment: Case Harden Case Hardness: 52-58 Rockwell C Case Depth: #6 Dia = .002” - .007” #8, #10, #12 Dia = .004” - .009” 1/4” = .005” - .011” Core Hardness Carbon Steel: 32-40 Rockwell C 410 Stainless: 42-48 Rockwell CDuctility: 5 Degree minimum bend
Shear
TECHNICAL DATABLAZER® SELF-DRILLING SCREWS
PULLOVER TEST RESULTS
TECHNICAL DATA
MINOR
MAJOR
BLAZER® ENGINEERING DATA
Physical Properties REV.JES082712
DRILL SCREWSBLAZER R
19
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD19.0616
Pullout Loads | Ultimate in Pounds ForceCarbon Steel and 410 Stainless Steel ScrewsThe tensile strength of the substrate that is used in the chart below is typical for metal building and roofing applications. Contact TFC if other substrate tensile strengths are required.
PULLOUT LOADSBLAZER® SELF-DRILLING SCREWS
FASTENER PULLOUT LOADS | DRILL SCREWSDRILL SCREWSBLAZER R
Fastener Information
PULLOUT | ULTIMATE LOAD IN POUNDSGrade 80 and Grade 50 Steel per ASTM A792/A1011/A653/A572/A529
Calculated Values In Accordance to AISI S100 | Section E4
Screw Size
Nom Dia.(in.)
Grade 80 (TS)
82Ksi Min.
Grade 50 (TS)65Ksi Min. Steel
26 Ga.(.018")
24 Ga.(.024")
22 Ga.(.030")
20 Ga.(.036")
18 Ga.(.048")
16 Ga.(.060")
14 Ga.(.075")
12 Ga.(.105")
1/8"(.125")
10 ga(.135")
1/4"(.250")
3/8"(.375")
1/2"(.500")
#8-18 .164" 156 218 272 326 435 543
#10-16 .190" 180 252 315 378 504 627 786 1,101 1,311
#10-24 .190" 180 252 315 378 504 627 786 1,101 1,311
#12-14 .216" 205 286 358 430 573 716 895 1,253 1,492 1,611
#12-24 .216" 1,492 1,611 2,984 *4,475 *5,967
1/4-14 .250" 237 332 414 497 633 829 1,036 1,450 1,727 1,865 3,453
1/4-20 .250" 1,727 1,865 3,453 *5,180 *6,906
5/16-12 .3125" 829 1,036 1,295 1,813 2,158 2,331
For allowable loads, please apply an appropriate Factor of Safety as required by local and national code requirements.
AISI S100 Section E4 recommends a Factor of Safety of 3 for allowable loads.
Because the tensile strength of the substrate dramatically affects the pullout of the fastener, TFC provides published pullout results based on a calculation developed by AISI.
The following pullout loads were calculated per AISI S100 | Section 4 of the Supplement No. 2 to the American Specification for the Design of Cold-Form Steel Structural members (S100-07/S2-10).
Many tests were conducted with compressible fiberglass insulation placed between steel sheet samples. It was determined by the results that the equations are valid for steel connections including applications that use compressible insulation. Refer to AISI S100 for more details.
• The pullout calculation requires the use of the nominal diameter of the screw and the tensile strength of the substrate.
• Because substrate tensile and specific fastener details like point diameter affects pullout loads, these pullout loads are conservative.
Fastener Pullout
F
DISCLAIMER: ALL TEST RESULTS AND SPECIFICATIONS ARE A RESULT OF LABORATORY TESTS. APPROPRIATE SAFETY FACTORS SHOULD BE USED BY THE USER OR SPECIFIER. DETERMINING THE PROPER FASTENER IS THE RESPONSIBILITY OF THE USER OR SPECIFIER. SINCE APPLICATION CONDITIONS VARY AND ARE UNCONTROLLABLE BY TFC, WE ASSUME NO LIABILITY FOR THE USE OF THIS INFORMATION.
* Denotes load exceeds tensile strength of screw.
For tested values, contact Triangle Fastener to conduct actual pullouttestsbasedonaspecificfastenerstyleandthetensilestrength requirement of the substrate.
20
CR
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD32.0616
DescriptionPoint Type
Carbon Steel
304 Stainless
Steel
410 Stainless
Steel
Stainless Cap Head
Zinc Cap Head
Box Qty.
Wgt. Per M
#14-10 x 3/4" Type A X X 2,500 10.8
#14-10 x 1" Type A X X X 2,500 14.2
#14-10 x 1-1/2" Type A X X X 1,500 19.1#14-10 x 2" Type A X X 1,000 23.4#14-10 x 2-1/2" Type A X X 1,000 28.1#14-10 x 3" Type A X X 500 34.1#14-10 x 4" Type A X X 500 45.5#14-10 x 5" Type A X X 300 52.8#14-10 x 6" Type A X X 250 60.11/4-14 x 3/4” Type AB X X X X 2,500 12.51/4-14 x 1” Type AB X X X X X 2,500 14.91/4-14 x 1-1/2” Type AB X 1,500 19.71/4-14 x 1-3/4” Type AB X 2,000 23.41/4-14 x 1” Type B X X 2,500 14.11/4-14 x 1-1/2” Type B X X 1,500 19.51/4-14 x 2” Type B X X 1,000 23.11/4-14 x 2-1/2” Type B X X 1,000 29.0
1/4-14 x 3” Type B X X 500 33.3
1/4-14 x 4” Type B X X 500 43.41/4-14 x 5” Type B X X 300 53.51/4-14 x 6” Type B X 250 62.21/4-14 x 8” Type B X 200 81.01/4-14 x 1” Type BP X 2,000 17.01/4-14 x 1-3/4" Type BP X 2,000 23.4#17-14 x 1” Type AB 1X X 1X X 2,000 18.9#17-14 x 1-1/2” Type AB X X X 1,500 28.4
We stock the largest section of self-tapping “sheeting” screws in USA!
• Select from carbon steel, 304 stainless steel, 410 stainless steel, zinc cap head or stainless steel cap head.
• Available with and without BOND-SEAL sealing washers.
• Available with TRI-SEAL® long life coating providing over 1,000 hours salt spray resistance (ASTM B117).
• Lengths up to 8” long!
• Can be painted with our KALIDA-KOTE™ paint process to match your specific color.
You want’em... we got‘em!
Refer to the back for technical information and drill bit size.
CARBON STEEL & STAINLESS STEELSELF-TAPPING SCREWS
Screwgun Speed: 1,000 rpm maximum
1/4-14 Type BPTapping Range
14ga - 1/2”
Used for alignment into structure.
#17-14 Type ABTapping Range
Up to 10ga Need a Back-out Resistant Tapping Screw?VRT® Technology produces 3-1/2 times more back-out resistance than a standard thread. Supplied with TRI-SEAL™ long life coating.
3/8" Zinc Cap Head
5/16" Stainless Cap Head
Available Head Styles
3/8" Hex Head (Standard)
3/8" Hex Washer Head (#17-14 VRT® Only)
Sizes (X = Available)
1Available with VRT® technology.
#14-10 Type ATapping Range
Up to 14ga & Wood
1/4-14 Type BTapping Range
14ga - 1/2”
1/4-14 Type ABTapping Range
Up to 10ga & Wood
Oversize or special sealing washers available!
21
CR
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD33.0616
Hole Size and Pullout Values
Sealing Washer InformationCarbon Steel Screws: 15MM O.D. Galvanized Steel / EPDM. Stainless Steel Screws: 15MM O.D. Stainless Steel / EPDM.#17 with VRT® Screws: 3/4" O.D. Galvanized Steel / EPDM.Zinc Cap Head and Stainless Cap Head: 5/8" O.D. Head / EPDM.
DISCLAIMER: ALL TEST RESULTS AND FASTENER RECOMMENDATIONS ARE BASED ON LABORATORY CONDITIONS. BECAUSE ACTUAL JOB SITE CONDITIONS VARY AND ARE UNCONTROLLABLE BY TFC. WE ASSUME NO LIABILITY FOR THE USE OF THIS INFORMATION.
Screw TypeMajor Dia..
TorsionalLb-in. Material
Tensile Lbs.
ShearLbs.
#14-10 Type A
.235”
.246" 125Carbon Steel 3,150 2,150
304 SS 2,925 1,925
1/4-14 Type AB & B
.237”
.246" 150Carbon Steel 3,850 2,575
304 SS 3,700 2,800
#17-14 Type AB
.280”
.290" 170Carbon Steel 5,890 3,285
304 SS 5,200 3,125
FASTENER DATA AND SuBmITTAL SHEET
Mechanical Properties
Carbon Steel ScrewsThese general purpose screws are designed for normal atmospheric conditions. They should not be used in heavy industrial applications or close proximity to the ocean where corrosion can occur. They are case hardened and can tap up to 1/2” thick steel using the appropriate hole size listed on this sheet.
410 Stainless Steel ScrewsThese screws can be used in mild atmospheres, steam, and many mild chemical environments. They provide superior strength and are plated or coated to provide lubricity during tapping. 410 screws may show signs of red rust but will not rust as quickly as carbon steel screws. Not recommended for use in aluminum connection. Expansion of the aluminum may stress the screw to failure due to the screw's hardness.
304 Stainless Steel Screws These screws are used in applications that require superior corrosion resistance or ductility. The chromium in the material reacts with oxygen forming a thin, invisible, non-reactive chromium oxide film. It is resistant to ordinary rusting in wastewater treatment, food-processing environments, and a wide variety of chemicals. 304 stainless steel screws are slightly magnetic caused during head and thread forming. They are not heat treated and are plated to provide lubricity that helps minimize thread roll-over caused during tapping.
Product: TFC Tapping ScrewsGeneral Specification: ANSI B18.6.4, AC 118)
Material: C 1018 / C 1022 410 Stainless SteelHeat Treat: Case HardenedFinish: .0003” Zinc Plated - 24 hrs salt spray / No red rust Optional: TRI-SEAL Coated – 1,000 hrs salt spray / No red rust
Material: Type 304 Stainless Steel (18-8)Heat Treat: NoneFinish: Type B & BP: .0003” Min. Cad Plating (For lubricity)Type A & AB: .0003” Min. Zinc Plating (For lubricity)Salt Spray: >2,000 hrs / No red rust
Pressure Treated or Fire Treated Wood ConnectionsScrew made of 410 or 300 series stainless steel are recommended. Carbon steel screws must be hot dipped galvanized or TRI-SEAL® coated. Do not use standard, zinc plated, carbon steel screws.
DRILL BITS SIZES
Screw Type26ga
(.018”)24ga
(.024”)22ga
(.030”)20ga
(.036”)18ga
(.048”)16ga
(.060”)14ga
(.075”)12ga
(.105”)1/8”
(.125”)10ga
(.134”)3/16”
(.187”)1/4”
(.250”)3/8”
(.375”)1/2”
(.500”)#14-10 Type A 1/8” 5/32” 3/16” Not recommended1/4-14 Type AB 1/8" 5/32" 3/16" #7 Not recommended1/4-14 Type B Not recommended 3/16" #7 #11/4-14 Type BP Not recommended 3/16" #7 #1#17-14 Type AB 3/16" 1/4" Not recommended
Use 135o split point drill bits for optimal performance.
PULLOUT Average Ultimate - Pounds
Screw TypeMTL
TYPE26ga
(.018”)24ga
(.024”)22ga
(.030”)20ga
(.036”)18ga
(.048”)16ga
(.060”)14ga
(.075”)12ga
(.105”)1/8”
(.125”)10ga
(.134”)3/16”
(.187”)1/4”
(.250”)5/16”
(.375”)3/8”
(.312”)1/2”
(.500”)
#14-10 Type A SS 270 363 363 459 657 1,194 1,368 1,780 1,812CS 276 342 342 464 747 1316 1414
1/4-14Type AB, B, BP
SS 216 344 344 411 541 686 983 1,698 2,242 2,855 2,693 3,695 3,746 3,784 3,790CS 444 676 1137 1477 1932 2426 3047 4591* 4587* 4621*
#17-14 Type AB CS 410 522 879 1277 2185
Application and Description
Material Information
CARBON STEEL & STAINLESS STEELSELF-TAPPING SCREWS
NOTE: SS = 304 Stainless Steel | CS = Carbon Steel & 410 Stainless Steel *Denotes exceeds tensile strength of screw
22
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD35.0616
Designed for fast installation and corrosion free performance. All fasteners can be painted with our Kalida-Kote™ paint finish to your exact color match. Polyurethane with UV protection provides a chip resistant finish without chalking and fading.
SizeGrip
Length Part #Box Qty.
BoxWt.
A #10-14 x 1" <.250" 10100HW17CSTSBW 3,000 26 lbs.
B #10-14 x 1-1/2" <.750" 10150HW17CSTSBW 2,500 28 lbs.
C #10-14 x 2" .500" - 1.250" 10200HW17CSTSBW 2,000 22 lbs.
D #10-14 x 2-1/2" 1.000" - 1.750" 10250HW17CSTSBW 1,500 19 lbs.
E #10-14 x 3" 1.500" - 2.250" 1030HW17CSTSBW 1,000 15 lbs.
F #12-14 x 3/4" LAP 12075HWBSTSBW 2,500 27 lbs.
G #12-8 x 1” <.250" 12100HW17CSTABW 3,000 23 lbs.
H #12-8 x 1-1/2” <.750” 12150HW17CSTABW 2,500 34 lbs.
I #12-8 x 2” .500" - 1.250” 12200HW17CSTABW 2,000 33 lbs.
J #14-10 x 1" <.250" 14100HWMCSTABW 3,000 43 lbs.
K #14-10 x 1-1/2” <.750” 14150HWMCTABW 2,000 38 lbs.
L #14-10 x 2" .500" - 1.250” 14200HWMCSTABW 1,500 34 lbs.
M #14-10 x 3" 1.500"- 2.250" 14300HWMCSTABW 1,000 32 lbs.
O #14-10 x 1-1/2" <.750" 14150HW17ZH 1,500 36 lbs.
Sizes
O
• Designed to provide ultimate pullout resistance.
• Available with TRI-SEAL® 1,000 hrs salt spray coating which is formulated for ACQ lumber applications.
• Designed for fast installation and corrosion free performance.
• Assembled with EPDM bonded washer for exceptional weatherability.
• Type 17 mill point eliminates splitting of wood.
G
H
I
J
K
Bagged 250 per bag
Fastener Sizes and SpecificationsA
B
C
D
E
Point Type: Type 17 | Drilling Thickness: 20ga. Max
PANEL-TITEMETAL-TO-WOOD SCREWS
R #10, #12, #14 METAL TO WOOD SCREWS
L
#14-10 x 1-1/2" is now available in long life
Zinc Head!
M
F
Lap Screw
Choose from the largest selection in the industry!
Paint
All fasteners can be painted with our Kalida-Kote paint finish to your exact color match.
Polyurethane with UV protection provides a chip resistant finish without chalking and fading.
Do you need a long life head or a stainless steel screw?
Please see Page MD36!
23
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD36.0616
METAL-TO-WOOD SCREWSStainless Steel Cap Heads and Stainless Steel
DescriptionDrilling
Thickness Part No.Carton
QuantityBoxWt.
F #9-15 x 1” GP .040 AL 09100HWGS34BW 3,000 pcs. 26 lbs.G #9-15 x 1-1/2” GP .040 AL 09150HWGS34BW 2,500 pcs. 26 lbs.H #9-15 x 2” GP .040 AL 09200HWGS34BW 2,000 pcs. 26 lbs.I #9-15 x 2-1/2” GP .040 AL 09250HWGS34BW 1,500 pcs. 25 lbs.J #9-15 x 3” GP .040 AL 09300HWGS34BW 1,000 pcs. 18 lbs.
SIZES
DescriptionDrilling
Thickness Part No.Carton
QuantityBox Wt.
A #10-12 x 1” GP 20ga. max 10100HWGCSTSSC 2,500 pcs. 30 lbs.
B #10-12 x 1-1/2” GP 20ga. max 10150HWGCSTSSC 2,000 pcs. 25 lbs.
C #10-12 x 2” GP 20ga. max 10200HWGCSTSSC 2,000 pcs. 33 lbs.
D #10-12 x 2-1/2” GP 20ga. max 10250HWGCSTSSC 1,000 pcs. 29 lbs.
E #14-10 x 3-1/2" 20ga. max 14300HWMCSSC 1,000 Pcs 38 lbs.
Diameter & Point: #9-15 Gimlet PointMaterial: 305 Stainless SteelPlating: Passivated Head Style: 1/4” HWHThread: #9-15 Double Lead
Diameter & Point: #10-12 Gimlet PointMaterial: Carbon Steel Shank, 304 Stainless Steel Cap HeadPlating: TRI-SEALTM CoatingHead Style: 1/4” HWHThread: #10-12 Double LeadSalt Spray: 1,000 hrs.
DISCLAIMER: ALL DATA AND SPECIFICATIONS ARE BASED ON LABORATORY TESTS. APPROPRIATE SAFETY FACTORS SHOULD BE USED BY THE USER OR SPECIFIER. DETERMINING THE PROPER FASTENER IS THE RESPONSIBILITY OF THE USER OR SPECIFIER. BECAUSE APPLICATION CONDITIONS VARY, WE ASSUME NO LIABILITY FOR THE USE OF THIS INFORMATION.
PANEL-TITEMETAL-TO-WOOD SCREWS
R
PANEL-TITE® SCHStainless Cap Head with Flange Sealer
• Use on 20yr warranty roof systems.• Carbon steel shank with TRI-SEAL® coating.• Provides outstanding corrosion protection.
A
B
C
D
PANEL-TITE® SS Stainless Steel with Stainless Steel Washer
• 305 stainless steel.• Used in aluminum applications.• Preferred screw for treated lumber.
G
H
I
F
J
Penetrates Steel up to 20 ga.
E
PANEL-TITE® SCHStainless Cap Head w/Flange Sealer
PANEL-TITE® SS Stainless Steel w/ Stainless Steel Washer
Attach metal panels with a 1-1/2"- 2" high rib height. Great for replacing screws that are stripped!
SUPERIOR CORROSION RESISTANCE & LONG-LIFE PERFORMANCE
24
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD37.0616
FastenerDia. & Point
Wood Type1/2” Ply
5/8” Ply
3/4” Ply
7/16” OSB
19/32” OSB
23/32” OSB
2 x 4 SYP
#9-15 GP 350 402 548 173 344 431 887
#10-9 Type 17 383 395 574 136 256 514 813
#10-13 GP 375 505 654 166 357 442 737
#10-14 High-Low 375 505 654 166 357 442 737
#12-8 Type 17 296 445 552 139 445 538 748
#14-10 434 475 626 153 327 475 1030
Material: Carbon SteelFinish: TRI-SEAL Long-life (ACQ Compatible) Material: 304 Stainless SteelFinish: Passivated. (ACQ Compatible)
Material: 304 Stainless Steel Plating: Zinc Plated
#12-11 Double Lead Lap
Pullout Values in Wood (Carbon Steel or Stainless Steel)Ultimate Average Load in Pounds Force
Strengths (Carbon Steel) Pullover Strength in Pounds
Corrosion Test ResultsTRI-SEAL® COATING
#12-8 Low Root with Type 17 Point
#10-14 Dual Thread with Type 17 Point
#14-10 Single Lead Type 17 Point
PANEL-TITE® TECHNICAL DATA SHEET
PaintKalida-Kote Polyurethane with UV stabilizer
PANEL-TITEMETAL-TO-WOOD SCREWS
R
MaterialSpecifications
PerformanceSpecifications
Sizes
DISCLAIMER: ALL TEST RESULTS AND FASTENER RECOMMENDATIONS ARE BASED ON LABORATORY CONDITIONS. BECAUSE ACTUAL JOB SITE CONDITIONS VARY AND ARE UNCONTROLLABLE BY TFC. WE ASSUME NO LIABILITY FOR THE USE OF THIS INFORMATION.
SizeTensile
(lbs. min)Shear
(avg. lbs. ult.)Torsional
(min. in. lbs.)
#9-15 CS 1,800 1,200 50
#9-15 SS 1,500 980 45
#10-9 1,850 1,216 65
#10-12 2,100 1,400 65
#10-14 1,850 1,216 65
#12-8 2,183 1,946 80
#12-11 2,778 2,000 92
#14-10 3,150 2,150 125
Washer Size
26ga(.19")
24ga(.023")
22ga(.031")
20ga(.035")
18ga(.049")
1/2" O.D. 515 674 875 1100 1627
9/16" O.D. 587 744 915 993 1246
15mm O.D. 564 810 1097 1166 1643
Testing Method *Results
SO2 Test Per ASTM G87 20 Cycles (2 liters)
Salt Spray Per ASTM B117 1,000 hours
*0% Red Rust
Test Setup: 2 x 4 - 1" embedment. All other tests full thread embedment.
#9-15 Dual Thread
Exceeds ASTM B633 Salt Spray requirements.
Rev JC022712Report #T279-10 / Farabaugh Engineering and Testing / 9.30.2010
25
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD11.0616
The fastener head and threads are produced from corrosion resistant stainless steel producing exceptional corrosion protection and superior ductility. A carbon steel drill point is hardened and welded to the body allowing the fastener to drill and tap in steel up to 1/2" thick!
304 STAINLESS STEELBI-METAL DRILL SCREWSEJOT BI-METAL SCREWS
Carbon Steel
304 SS
Bi-Metal Screws
MANY MORE SIZES AVAILABLE!Visit our website for a complete offering and technical information.
We offer the largest selection of stainless steel bi-metal screws designed for superior performance!
26
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD34.0616
Designed for fast penetration, produces less chips, and provides exceptional corrosion protection
TECHNICAL INFORMATION
Our BURR-BUSTER™ Technology screws were developed for exterior applications or where corrosion is a concern. The proprietary dual thread was designed to penetrate steel faster with less chips than ordinary self-piercing screws. The screws are provided with TRI-SEAL™ 1,000 hour salt spray coating for superior corrosion protection.
Description: #10-16 Gimlet Point Self Piercing Screw with BURR-BUSTER™ Head Style: 5/16” HWH | Modified Truss with #2 Square Recess Material: C1022 carbon steel Heat Treat: Case hardened to ANSI/ASME B18.6.4 specification Finish: TRI-SEAL™ long-life coating (1,000hrs. salt spray)
SELF-PIERCING SCREWSTEEL FRAMING AND TRIM
SIZESDescription
Piercing Thickness Part Number
BoxQuantity
Wgt. Per Box
#10-16 x 3/4” w/ BURR-BUSTER Point | 5/16” HWH
2 x 20 ga. max (.072”) 10075HWBPCSTS5 4,000 25.3 lbs
#10-16 x 3/4” w/ BURR-BUSTER Point | Mod Truss w #2 Sq. Recess
2 x 20 ga. max (.072”) 10075MTBPCSTS5 4,000 25.3 lbs.
FEATURES AND BENEFITS• Coarse thread clamps steel tightly and reduces
screw back-out.
• BURR-BUSTER™ Technology is design for fast piercing of the steel up to 2x 20 gauge producing minimal chips.
• Applied is our TRI-SEAL™ 1,000 hour salt spray coating for use in exposed applications or when corrosion is a concern.
ApplicationsTrim • Gutter Straps • Steel Framing • HVAC Signs • Flashing
DISCLAIMER: ALL TESTS RESULTS AND SPECIFICATIONS ARE A RESULT OF LABORATORY TESTS. APPROPRIATE SAFETY FACTORS SHOULD BE USED BY THE USER OR SPECIFIER. DETERMINING THE PROPER FASTENER IS THE RESPONSIBILITY OF THE USER OR SPECIFIER. SINCE APPLICATION CONDITIONS VARY AND ARE UNCONTROLLABLE BY TFC, WE ASSUME NO LIABILITY FOR THE USE OF THIS INFORMATION.
Fastener Diameter
Nominal Screw Diameter
Major Diameter (inch)
Minor Diameter (inch)
Area Of Minor Dia. (sq in.)
Torsional (Lb-In.)
Tensile(Pounds)
Shear(Pounds)
Max Min Max Min#10-16 0.190 0.189 0.183 0.141 0.135 0.0143 61 2,100 1,400
Supplied in convenient 250 piece bags
Pullout Avg. Ultimate in Pounds
24-ga (.024”) 252 lbs.22-ga (.030”) 315 lbs.20-ga (.036”) 378 lbs.18-ga (.048”) 504 lbs.
PROBLEM Do you have rusty screws? Do you think you can use standard zinc plated screws in any application? Think again...they are not designed for exterior applications and rust quickly.
#2 Square Recess for positive drive stability
REV JS110615
BURR-BUSTERSELF-PIERCING SCREWS
TM
BURR-BUSTER™ Technology produces less burrs compared to ordinary self-piercing screws.ORDINARY SCREW BURR-BUSTER
BURR-BUSTER™ Screws are provided with our TRI-SEAL™ 1,000 hour salt spray coating, which is 40 times more corrosion resistant than zinc plated screws.
SOLUTION
PROBLEMOrdinary self-piercing screws produce burrs during installation that can damage surface and corrode quickly!
SOLUTION
Calculated Values In Accordance to AISI S100 | Section E4
Grade 50 Steel per ASTM A792/A1011/A653/A572/A529
Use in metal or wood!
27
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD228.0616
• Polyurethane enamel can be matched to any color and is UV resistant!
• Baked on finish provides a tough, chip resistant finish.
• Customized painting of metal closure and gutter straps.
• Special colors in 3 days or less!!
Specifically Formulated for Fasteners, Rivets, & Metal Closures
Our 4-step process assures a perfect color match and durable finish!
PAINT FOR FASTENERS, RIVETS & CLOSURES
STEP 1Color Matching
We color match using a spectrophotometer that provides
consistent color matching.
Abrasion & ME Abuse Excellent Acids Excellent
AlkalisExcellent
Color & Glass Retention
Excellent
Humidity Excellent Salts Excellent
Solvents Very Good Weather Excellent
STEP 2Priming
Special etching primer provides a superior base for the application of
the paint.
STEP 3Spraying
Polyurethane enamel is applied uniformly to provide
superior coverage.
STEP 4CuRINg
We cure the paint to produce a tough chip
resistant finish.
Triangle Fastener offers Kalida-Kote painting process, producing perfect color matched fasteners, rivets, and metal closure. We start by using a special formula polyurethane enamel with UV protection that is expertly color matched.After spraying, we cure the finish by baking to produce a tough chip resistant finish assuring long-life. Kalida-Kote is compatible with Kynar paint finishes.
SpecificationsFinish: Gloss Enamel 85 units minimum at 60 degrees Exterior Catalyst
Thickness: 1.6 - 2.0 mils
Adhesion: ASTM D 3359 - Excellent No peeling or removal
Impact Resistance: ASTM D 2794 Good: > 10 in.lbs.
Abrasion Resistance: ASTM D 4060 Good
Corrosion Resistance: Salt Spray - 1,000 hrs (< 5% red rust) Kesternich - 30 cycles
KALIDA-KOTE™ is compatible with Kynar®
paint finishes.
28
CR
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD21.0616
Corrosion TestingSalt Spray: 1,000hrs.Per ASTM B117. No red rust Kesternich: 30 cycles | 1.0 L15 cycles | 2.0 LASTM G87No Red Rust
Exceeds salt spray requirement specified in ASTM B633, B659, & F1941 (zinc plating).
DISCLAIMER: ALL TEST RESULTS AND SPECIFICATIONS ARE A RESULT OF LABORATORY TESTS. APPROPRIATE SAFETY FACTORS SHOULD BE USED BY THE USER OR SPECIFIER. DETERMINING THE PROPER FASTENER IS THE RESPONSIBILITY OF THE USER OR SPECIFIER. SINCE APPLICATION CONDITIONS VARY AND ARE UNCONTROLLABLE BY TFC, WE ASSUME NO LIABILITY FOR THE USE OF THIS INFORMATION.
Contact TFC for additional details on TRI-SEAL®.
TRI-SEAL™ Long-Life Coating is a high performance dip spin finish, developed to minimize corrosion when used in exterior building applications. It consists of three layers; the first layer is a metallic zinc layer, the second layer is a high-grade anti-corrosion chemical conversion film and the third, outer layer, is a baked ceramic surface coating.
The distinguishing feature of TRI-SEAL® is the tight joining of the baked ceramic surface coating and the chemical conversion film. These two layers are bonded together through chemical reactions, and this unique method of combining layers result in a rigid combination of the coating films.
■ Excellent resistance against gas, weather, and other kinds of corrosion factors, including salt water.
■ Compatible for use in Treated and Fire Treated Lumber. ■ Composite layers minimize the effect of scratches on the
protection coating. ■ Compatible for use in aluminum applications.
Test Items Test Methods Test Results
Hardness Peeling test by pencil hardness Over 4H
Adhesion Peeling test by adhesive tape on cross scribed test piece in 1 mm width Nothing abnormal
Acid Resistance Immersion in 5% sulfuric acid solution for 24 hours Nothing abnormal
Alkali Resistance Immersion in 5% sodium hydroxide solution for 72 hours Nothing abnormal
Heat Resistance Exposure to 250 C (482 F) heat for an hour Nothing abnormal
Accelerated Weathering Sunshine weather-0-meter test for 1,000 hours Free from red rust
Contact Corrosion w/other Metals
Corrosive investigation after Salt Spray Test (JIS Z2371) done comparatively on surface treated steel bolts/nuts tightened on a stainless steel plate
Clearly superior to zinc electroplated (colored
chromate) and hot dip galvanizing
Layer 1 - Baked Ceramic Surface Coating Layer Corrosive elements are intercepted by the strong paint film made of ceramic materials.
Layer 2 - Chemical Conversion Coating Layer Rust proof performance is improved as the chemical conversion inactivates the zinc plated surface and creates a tight adhesion between the chemically converted layer and the paint layer.
Layer 3 - Metallic Zinc Layer The steel / iron substrate is protected from corrosion by the self-sacrificial galvanic effect of the zinc coating.
Layer 4 - Fastener
Salt Spray Test Results1,000hrs Per ASTM B117 - No Red Rust
Applications: Exceeds salt spray requirement specified in ASTM B633, B659, & F1941 (zinc plating). Compatible for use in treated lumber
SEM IMAGING
TRI-SEAL® LONG-LIFE COATING
MATERIAL PROPERTIES
TRI-SEAL® 1,000 HRS SALT SPRAY COATING
29
CR
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD278.0616
FASTENER SElECTION guIDE FOR EXPOSEDmETAl buIlDINg AND ROOFINg APPlICATIONS
Environments
NOTE: Electroplated zinc plated screws are not for use in exterior applications and will corrode quickly.
For detailed product information, please view our product page located on our website or our PRODUCT QUICK FACTS sheet.
DRILL SCREWSBLAZER R PANEL-TITE
METAL-TO-WOOD SCREWS
R TFC TAPPERSSELF-TAPPING SCREWS
• TRI-SEAL® Coated | Carbon Steel• Stainless Cap or Zinc Head• 410 Stainless Steel
• TRI-SEAL® Coated | Carbon Steel• Stainless Steel Cap Head Screws• 304 Stainless Steel
To minimize galvanic corrosion, it is important that the fastener material is compatible with the roofing material. The following list of fasteners were selected based on specifications from various panel producers throughout the world. Harsh environments can corrode metals quickly. Contact the panel manufacturer for their specific recommendations.
URBAN/RURAL
COASTAL/MARINEINDUSTRIAL
Select a fastener based on the environment and the panel type.
304 STAINlESS STEElSTAINlESS CAP CARbON STEEl
TRI-SEAl® COATED*410
STAINlESS STEElZINC HEAD
304 STAINlESS STEElSTAINlESS CAP CARbON STEEl
TRI-SEAl® COATED ZINC HEAD
304 STAINlESS STEEl*410
STAINlESS STEEl
304 STAINlESS STEElSTAINlESS CAP *410
STAINlESS STEEl
• TRI-SEAL® Coated | Carbon Steel• Stainless Steel Cap Head• 304 Stainless Steel
• 304 Stainless Steel Bi-Metal Drill Screws
URBAN/RURAL
COASTAL/MARINEINDUSTRIAL
URBAN/RURAL
COASTAL/MARINEINDUSTRIAL
URBAN/RURAL
COASTAL/MARINEINDUSTRIALURBAN/RURAL
INDUSTRIAL
URBAN/RURAL
COASTAL/MARINEINDUSTRIAL
URBAN/RURAL
COASTAL/MARINEINDUSTRIAL
URBAN/RURAL
COASTAL/MARINEINDUSTRIALURBAN/RURAL
URBAN/RURALINDUSTRIAL
URBAN/RURAL
COASTAL/MARINEINDUSTRIAL
URBAN/RURAL
COASTAL/MARINEINDUSTRIAL
URBAN/RURAL
COASTAL/MARINEINDUSTRIALURBAN/RURAL
INDUSTRIAL
SD304 Stainless Self-Drill Screws
300
• Galvanized• Zinc/Aluminum• Painted Metal
COATED STEELPANEL MATERIAL
Fasteners
WR WR WR
WR WR WR
WR
WR WR
STAINlESS CAP URBAN/RURAL
COASTAL/MARINEINDUSTRIAL
WR
Note: 300 series stainless may corrode the base metal in severe marine environments. Consult the panel manufacturer for specific conditions
*Coated or Zinc Plated
*Coated or Zinc Plated
Form # JS0413
COPPERPANEL MATERIAL
STAINLESS STEEL
PANEL MATERIAL
Fasteners
Fasteners
Fasteners
ALUMINUMPANEL MATERIAL
Use With Warranted Roof SystemsWR
*Coated or Zinc Plated
URBAN/RURALINDUSTRIAL
Note: 300 series stainless may corrode the base metal in severe marine environments. Consult the panel manufacturer for specific conditions
30
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD279.0616
To eliminate confusion and assure the proper screw is used, specifications for tapping screws should be written to include;
1. Thread diameter2. Threads per inch3. Point type4. Description of the type of screw5. Drive size6. Head Style7. Material8. Finish / plating
FASTENING TIPS
Allow at least three (3) full threads to extend beyond the material being fastened.
Drilling Thickness (Drill Point Type)Add up the total thickness that will be drilled by the screw and select a drill point type that meets the required drilling thickness range. (Do not include pre-punched materials that will not be drill by the screw.)
Select the desired drill point type located on the size chart of the BLAZER® / CONCEALOR® sell sheet (i.e. BLAZER-5).
Disclaimer: Hardware should always be installed by a competent professional with a good understanding of interior wall types and mounting fasteners. Please do not attempt to install any hardware unless you know how to safely operate the necessary tools, and have a good understanding of what you are doing. The following instructions are basic guidelines for qualified installers, and should be read through completely before starting your job.
The following information is provided to help you specify and install tapping screws correctly. Care should be used when selecting and installing screws to assure optimal performance.
Using the proper tooling is important for producing consistent installation. It also minimizes potential screw or application failure caused by over-driven and under-driven fasteners.
Recommended Screw-Gun Speed
Screw Size Max RPM#6, #8, #10 2,500 All wood screws 2,500 #12, 1/4”, 5/16” 2,000 All DP5 2,000 304 Stainless Screws 1,200
Specifying and Installing
HEAD TYPE
SCREW LENGTH
PILOTLENGTH
THREADSPER INCH
POINTTYPE
THREADDIAMETER
DETERMINE DRILL POINT TYPE
* Drilling Thickness
**
Attachment Thickness
INSTALLATION TECHNIQUES
ACCESSORY TIPS
Worn out drive bits and sockets produces poor drilling, can strip the recess, and damage painted fasteners.
Look familiar?
SEALING WASHERSTo assure a proper seal, tighten the screw until the EPDM sealant extrudes just to the outer edge of the backing material. This also is a great way to visually inspect the screw to assure it is properly sealed.
Correct
Too Tight!
Too Loose!
• Install fastener perpendicular to the work surface.
• Let the drill point do the work.• Use a tool with torque control
or depth sensing nose piece to prevent over-torqued and under-torqued screws.
• Allow all material to be drilled before tapping into the steel.
• Do not exert excessive pressure!• Do not over drive the screw!• Do not use impact tools! (They
can torque the screw to failure!)
Do
Do Not
TERMINOLOGY
Example1/4-14 x 1” DP3 BLAZER Drill Screw. 3/8” HWH. Carbon Steel. TRI-SEAL™ 1,000 hour coating.
1/4 - 14 x 1” DP3 3/8” HWH
ThreadDiameter
ThreadsPer Inch
ScrewLength
PointType
Head Size& Type
IncorrectCorrect
SET THE MAGNET!Be sure screw head engages into the socket completely. This will eliminate screw wobble, improve the drilling performance, and reduce damage to painted screw heads.
Attachment Thickness | METALMeasure from the top surface of the material being fastened to the underside of the metal. Be sure to allow for any void or insulation.
Select a screw length listed in the BLAZER® or CONCEALOR® sell sheet (attachment length).
WARNING! DO NOT USE IMPACT TOOLS FOR INSTALLATION!Using impact tools to install pancake head screws can cause the head to separate from the body due to the high torque and impulse generate by the tool. HWH screws can also be easily overtighten which can lead to connection failure.
TFC is not responsible for failures caused by the use of improper tooling or improper installation.
Attachment Thickness | WOODAllow full penetration into wood decks so the screw point extends beyond the bottom side. Allow at least 1” screw embedment in 2 x structures to maintain designed pull out resistance. Greater penetration can achieve higher pull out values.
Allow screw tip to extend beyond decking.
DETERMINE FASTENER LENGTH
© Triangle Fastener Corporation 201631
CR
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD160.0616
Outside Diameter Screw Size1/2" (9mm) .........#10, #12, 1/4", #14
9/16" ................#12
5/8" (15mm) .......#10 , #12, 1/4", #14, #17, 5/16"
.729" ................1/4", #14", 5/16", 3/8
1" ................5/16", 1/2"
1-1/8" ................1/4", #14
1-13/16" .............5/16"
1-1/2" ................1/4", #14, 5/16"
AZTEC MasterSeal washers are a practical and simple, yet sturdy and reliable. They are engineered to prevent delamination of metal and sealant.
Features and Benefits• Vulcanized for optimal strength.• Aluminum, stainless steel or galvanized steel backing standard; Monel backing also available.• EPDM sealer standard; neoprene and silicone also available.• Deflectable, tapered lip on inside diameter assures inner seal around fastener.• Sealant evenly compresses to create a uniform seal.• Resists shearing and tearing during application.• Retains positive seal regardless of position on flat surfaces and many curved surfaces.• Allows visual confirmation of proper seating.
InstallationExtrusion of sealant at outer edge of properly seated washer provides easy conformation of proper fastener seal. Correct
Slight circle of sealant extrusion.
Too Tight Metal backing
begins to turn up.
Too Loose Sealant is not compressed
and can not form seal.
20 Gage GalvanizedSteel Backing
20 Gage 304 Stainless Steel Backing .040 Aluminum 5052 Backing
MASTER SEAL™ Washers Provide An Air, Vapor Or Liquid-Tight Seal
Property Value Test Method Base Material ..................................... Cross-Linked EPDM (Ethylene propylene di ene terpolymer) ...................N/A
Color ................................................... Black ............................................................................................................N/A
Test Level ........................................... 3 ...................................................................................................................Grade
Test Temperature................................ B 100 degrees C .........................................................................................Type
Volume Swell ...................................... A No Requirement .......................................................................................Class
Durometer Hardness .......................... 70 +/- 5ASTM ..............................................................................................D2240
Tensile Stength ................................... 10 MPa (1450 PSI) Minimum ......................................................................ASTM D412
Ultimate Elongation ............................ 250% Minimum ............................................................................................ASTM 412 A/C
Heat Resistance ................................. Heat aging 70 hrs @ 100 degrees C ..........................................................ASTM D573
Change / Hardness Maximum + 10 Points Change / Tensile Maximum - 25% Change / Ultimate Elongation Maximum - 25%
Compression Set ................................ Maximum 25% .............................................................................................ASTM D395B
Ozone Resistance .............................. No observed effect (70 hrs. @ 50 pphm) ....................................................ASTM D1171
100% Quality Retention Facing
Low Temperature Brittleness .............. Non-brittle 3 minutes@ -55 degrees C ........................................................ASTM D2137
UV Resistance ................................... Excellent Resistance To Aging ........................... Excellent Non-standing ...................................... Pass
Typical properties of Bonded EPDM Sealing Washer Material
BONDED WASHERS
SIZESSealant: EPDM
Outside Diameter Screw Size1/2" (9mm) .........#10, #12, 1/4", #14
9/16" ................#12
5/8" (15mm) .......#10, #12, 1/4", #14, #17, 5/16"
.729" ................1/4", #14, 5/16", 3/8
7/8” ................3/8”
1" ................5/16", 1/2"
Outside Diameter Screw Size9/16" ................#12, 1/4”, #14
5/8" (15mm) .......#10 , #12, 1/4”, #14
.729" ................ 5/16", 3/8
1” ................5/16”
1-3/16”" ..............5/16”
1-1/2” ................5/16”
SADDLE WASHERSWe can provide saddle washers
for a variety of panel types. Contact TFC for sizes.
Styles for flat and curved ribs
32
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD45.0616
Select your specific panel color or manufacturer and find the appropriate rivet!
#43 & #44 STAINLESS RIVETS We've developed an easy to use color chart to help find the perfectly color matched rivet!
GET-A-GRIPPAINTED RIVETS
TM
Color Manufacturer Name TFC Rivet
Color Rivet Part No.
Aged Bronze Berridge Roman Bronze FBF44RBZFBF43MBZ
Aged Copper Ryerson (INTEGRIS)
Aged Copper FBF44ACPPeterson / Pac-CladAmerican Buildings Co.CentriaVic West
Almond Copper Sales / Firestone Metal Product / Una-Clad
Almond
FBF44ALFBF43AL
Ryerson (INTEGRIS)MBCIPeterson / Pac-CladValspar
Architectural Red McElroy Metals Rustic Red /
Red ClayFBF43RRD FBF44RDCL
Arctic White VP Buildings Polar White / Stone White
FBF43PWH FBF44SWH
Ash Gray FabralAsh Gray FBF43AGYU S A
Vic WestAztec Gold U S A Aztec Gold FBF43AGDBanner Red Ryerson (INTEGRIS) Crimson Red /
Banner RedFBF43CRD FBF44BRD
Blue Fabral Hawaiian Blue / Slate Blue
FBF43HBLFBF44SLBL
McElroy MetalsMetal EraVic West
Bone White Alcoa
Bone White FBF44BNWH
AtasBerridgeCentriaCopper Sales / Firestone Metal Product / Una-CladEnglertPetersen / Pac-CladRyerson (INTEGRIS)
Boysenberry AEP SpanCordovan FBF44CDAtas
VP BuildingsBrandywine Copper Sales / Firestone Metal
Product / Una-CladCordovan FBF44CDMcElroy Metals
Metal EraBrick Red AEP Span
Rustic Red / Red Clay
FBF43RRD FBF44RDCLMetal Sales
VP BuildingsBright Red AEP Span Crimson Red /
Banner RedFBF43CRD FBF44BRD
Bristol BlueBerridge
Hawaiian Blue / Slate Blue
FBF43HBL FBF44SLBL
Brite Red American Buildings Co.
Crimson Red /Banner Red
FBF43CRD FBF44BRD
AtasDMI (Dimensional Metals)FabralMcElroy MetalsVic West
Brite White McElroy Metals Polar White FBF43PWHBrown Fabral
Koko Brown FBF43KBRNVic WestCentria Mansard
Brown FBF44MBRNDMI (Dimensional Metals)
Buckskin Tan Kirby / Gulf States Light Stone FBF43LST
Burgundy
ABC
Cordovan FBF44CD
BerridgeButlerCentriaClad-TexConsolidated MetalsDMI (Dimensional Metals)Englert Metal SalesPeterson / Pac-CladVic West
Color Manufacturer Name TFC Rivet Color Rivet Part No.
Burnished Slate
ABC
Burnished Slate FBF43BSL
American Buildings Co.Fabral MBCIMetal SalesNucorSpircoU S AVic West
Burnt Umber Gulf States Rustic Red / Red Clay
FBF43RRD FBF44RDCLKirby
Cape Blue Ryersen (INTEGRIS) Cape Blue FBF44CPBLCardinal Red Petersen / Pac-Clad Crimson Red /
Banner RedFBF43CRD FBF44BRD
Charcoal / Charcoal Gray
ABC
Charcoal Gray FBF43CGY FBF44CHGY
American Buildings Co.BerridgeEnglertFabralFirestone / Una-CladMBCIMcElroy MetalsMetal EraMetal SalesNucorPetersen / Pac-CladRyerson (INTEGRIS)SpircoUnion CorrugatingU S AVic West
Cherokee Blue Ryersen (INTEGRIS) Cherokee Blue FBF44CHBL
Colonial Red AEP Span
Colonial Red FBF44CRD
Alcoa
Berridge
CentriaClad-TexCMF (Consolidated Metals)Copper Sales / Firestone Metal Product / Una-CladDMI (Dimensional Metals)EnglertGulf StatesKirby LibertyMBCIMcElroy MetalsMetal EraPetersen / Pac-CladReynoldsRyerson (INTEGRIS)U S A
Colony Green U S A Colony Green FBF43COGR
Copper Brown Berridge Mansard
Brown FBF44MBRN
Copper Cote Berridge Copper Penny FBF44CPNYCopper Penny
AEP SpanMetallic Copper
FBF43MCP FBF44MCP
McElroy MetalsPetersen / Pac-CladVP BuildingsRyerson (INTEGRIS) Copper Penny FBF44CPNY
Cordovan Ryerson (INTEGRIS) Cordovan FBF44CDCountry Red U S A Rustic Red /
Red ClayFBF43RRD FBF44RDCL
Crimson Red ABCCrimson Red /Banner Red
FBF43CRDFBF44BRD
FabralSpircoVic West
Dark Blue AEP SpanDark Blue FBF44DBL
SpircoDark Bronze AEP Span
Dark Bronze FBF43DBZ FBF44DBZ
AlcoaBerridgeCentriaClad-TexCMF (Consolidated Metals)Copper Sales / Firestone Metal Product / Una-CladDMI (Dimensional Metals)EnglertGulf StatesMcElroy MetalsMetal EraMetal SalesPetersen / Pac-CladRyersen (INTEGRIS)
Deep Red Berridge Crimson Red / Banner Red
FBF43CRD FBF44BRDEnglert
GET-A-GRIPPAINTED RIVETS | #43 & #44
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD46.0616
GET-A-GRIPPAINTED RIVETS
TM
Select your specific panel color or manufacturer and find the appropriate rivet! Color Manufacturer Name TFC Rivet
Color Rivet Part No.
Denim Blue Gulf StatesGallery Blue FBF43GBL
KirbyDesert Sand ABC
Desert Sand FBF43DSSpircoU S A
Desert Tan VP Buildings Desert Sand FBF43DSDiamond White
Gulf StatesPolar White FBF43PWH
KirbyEgyptian White VP Buildings Light Stone FBF43LST
Evergreen ABC
Classic Green FBF43CGR FBF44CGR
AlcoaAmerican Buildings Co.CentriaCMF (Consolidated Metals)McElroy MetalsUnion Corrugating
Extra Dark Bronze
Copper Sales / Firestone Metal Product / Una-Clad Dark Bronze FBF44DBZ
Felt Green AEP Span Fern Green /Hartford Green
FBF43FGR FBF44HGR
Fern GreenMBCI
Fern Green / Hartford Green
FBF43FGR FBF44HGR
Fieldstone Bronze
Gulf States Burnished Slate FBF43BSL
KirbyForest Green AEP Span Fern Green
/ Hartford Green
FBF43FGRFBF44HGRAtas
Metal SalesBerridge
Classic Green FBF43CGRFBF44CGREnglert
Petersen / Pac-CladGoldenrod Metal Sales Aztec Gold FBF43AGDGulfstream Blue
Gulf States Hawaiian Blue / Slate Blue
FBF43HBL FBF44SLBLKirby
Harbor Blue MBCIHarbor Blue FBF43HRBL
U S AHartford Green
Atas
Fern Green / Hartford Green
FBF43FGR FBF44HGR
BerridgeCentriaClad-TexCopper Sales / Firestone Metal Product / UnaCladDMI (Dimensional Metals)EnglertMcElroy MetalMetal EraPetersen / Pac-CladRyerson (INTEGRIS)
Hawaiian Blue
MBCI Hawaiian Blue / Slate Blue
FBF43HBL FBF44SLBLMetal Sales
U S A
Hemlock Green
AEP Span
Hemlock Green FBF44HMGR
American Buildings Co.AtasBerridgeConsolidated MetalsCopper Sales / Firestone Metal Product / Una-CladEnglertGulf StatesMetal EraPetersen / Pac-CladVic West
Hunter Green MBCI
Fern Green / Hartford Green
FBF43FGRFBF44HGR
Interstate Blue Petersen / Pac-Clad Royal Blue FBF44RBL
Jade Green AEP Span Teal FBF44T
Kelly Green FabralClassic Green FBF43CGR
FBF44CGRVic West
Koko Brown ABC
Koko Brown FBF43KBRN Metal SalesMBCISpirco
Leaf Green AEP SpanClassic Green FBF43CGR
FBF44CGRButlerVP Buildings
Light Stone ABC
Light Stone FBF43LST
American Buildings Co.FabralGulf StatesMBCIMcElroy MetalsMetal SalesNucorU S AVic West
Color Manufacturer Name TFC Rivet Color Rivet Part No.
Mansard Brown
Clad-Tex
Mansard Brown FBF44MBRN
Copper Sales / Firestone Metal Product / Una-CladEnglertMcElroy MetalMetal EraPetersen / Pac-CladReynoldsRyerson (INTEGRIS)
Matte Black
AEP Span
Matte Black FBF44MBLK
AlcoaBerridgeButler / LibertyClad-TexConsolidated MetalsCopper Sales / Firestone Metal Product / Una-CladDMI (Dimensional Metals)EnglertMcElroy MetalsMetal EraPetersen / Pac-CladRyerson (INTEGRIS)
Medium Blue
AEP Span Gallery Blue / Royal Blue
FBF43GBLFBF44RBLVP Buildings
Medium Bronze
AEP Span
Medium Bronze / Roman Bronze
FBF43MBZ FBF44RBZ
AlcoaAtasBerridgeClad-TexCopper Sales / Firestone Metal Product / Una-Clad EnglertMBCIMcElroy MetalsMetal EraPetersen / Pac-Clad
Military Blue Petersen / Pac-Clad Hawaiian Blue / Slate Blue
FBF43HBL FBF44SLBL
Mocha Tan Metal Sales Sahara Tan FBF43STN
Musket Gray
Petersen / Pac-CladMusket Gray FBF44MGY
Ryerson (INTEGRIS)
Ocean Blue Metal Sales Harbor Blue FBF43HRBL
Oyster White
Nucor Polar Whit e FBF43PWH
Reynolds Almond FBF43AL FBF44AL
Pacific Blue Clad-Tex
Pacific Blue FBF44PBLEnglertMBCIRyerson (INTEGRIS)
Parchment AEP SpanSandstone FBF44SST
Berridge
Patina Green
AEP SpanAged Copper FBF44ACP
FBF44ACPBerridgeAlcoa
Colony Green FBF43COGR
AtasClad-TexConsolidated MetalsCopper Sales / Firestone / Una-CladMcElroy MetalsMetal EraMetal SalesReynolds
Patrician Bronze
McElroy Metals Burnished Slate FBF43BSL
VP Buildings
Patriot Red Metal Sales Crimson Red / Banner Red
FBF43CRD FBF44BRD
Polar White ABC
Polar White FBF43PWH
Butler / LibertyFabralMBCIMetal SalesU S AVic West
Red Fabral Rustic Red / Red Clay
FBF43RRD FBF44RDCLVic West
Red Clay Ryerson (INTEGRIS) Red Clay / Rustic Red
FBF43RRD FBF44RDCL
Redwood AEP Span Terra Cotta FBF44TCMetal Sales Colonial Red FBF44CRD
Reflective White
American Buildings Co.
Polar White FBF43PWHFabralGulf StatesKirby
GET-A-GRIPPAINTED RIVETS | #43 & #44
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD47.0616
GET-A-GRIPPAINTED RIVETS
TM
Select your specific panel color or manufacturer and find the appropriate rivet! Color Manufacturer Name TFC Rivet
Color Rivet Part No.
Regal Blue Alcoa
Gallery Blue / Royal Blue
FBF43GBL FBF44RBL
American Buildings Co.AtasButler / LibertyConsolidated MetalsCopper Sales / Firestone Metal Product / Una-CladFabralGulf StatesMcElroy MetalsMetal Era
Regal Red Alcoa
Crimson Red / Banner Red
FBF43CRD FBF44BRD
Consolidated MetalsCopper Sales / Firestone Metal Product / Una-CladMetal Era
Regal White ABCPolar White FBF43PWHAlcoa
McElroy MetalsAEP Span
Snow White /Snowdrift White
FBF43SWH FBF44SDWH
Butler / LibertyCentria Consolidated MetalsGulf StatesVP Buildings
Roman Blue McElroy Metals Hawaiian Blue / Slate Blue
FBF43HBL FBF44SLBLNucor
Roman Bronze Ryerson (INTEGRIS)
Medium Bronze / Roman Bronze
FBF43MBZ FBF44RBZ
Royal Blue Berridge Gallery Blue /Royal Blue
FBF43GBL FBF44RBLIntegris
Rustic Red ABCRustic Red / Red Clay
FBF43RRD FBF44RDCL
Gulf StatesKirbyMBCI
Sage Integris Sage FBF44SGESagebrush Nucor Sahara Tan FBF43STNSahara Tan U S A
Sahara Tan FBF43STNUnion Corrugating
Sand Tan FabralAztec Gold FBF43AGD
Vic WestSandstone ABC
Sandstone FBF44SST
AlcoaAtasCentriaClad-TexConsolidated MetalsCopper Sales / Firestone Metal Product / Una-CladDMI (Dimensional Metals)EnglertMcElroy MetalsMetal EraPetersen / Pac-Clad
Scarlet Red MBCI Crimson Red / Banner Red
FBF43CRD FBF44BRD
Seaport Ryerson (INTEGRIS) Seaport FBF44SPShasta White Berridge Stone White FBF44SWHSherwood Green
Copper Sales / Firestone Metal Product / Una-Clad
Fern Green /Hartford Green
FBF43FGR FBF44HGR
Sierra Gold McElroy MetalsAztec Gold FBF43AGD
NucorSierra Tan Atas
Sierra Tan FBF44STN
BerridgeClad-TexConsolidated MetalsCopper Sales / Firestone Metal Product / Una-CladEnglertMetal EraPetersenRyerson (INTEGRIS)
Sky Blue AlcoaHawaiian Blue / Slate Blue
FBF43HBL FBF44SLBL
Copper Sales / Firestone Metal Product / Una-CladMetal Era
Color Manufacturer Name TFC Rivet Color Rivet Part No.
Smokey Blue AEP Span Hawaiian BlueSlate Blue
FBF43HBLFBF44SLBLVP Buildings
Slate Gray Alcoa
Slate Gray FBF43SGYFBF44SGY
American Buildings Co.AtasCentriaConsolidated MetalsCopper Sales / Una-Clad / FirestoneDMI (Dimensional Metals)EnglertFabral / VicWestGulf StatesIntegris / RyersonKirbyMBCIMcElroyPetersen / Pac-CladReynolds
Snow White Butler Snow WhiteSnowdrift White
FBF43SWHFBF44SDWHMBCI
Snowdrift White Integris / Ryerson
Snow WhiteSnowdrift White
FBF43SWHFBF44SDWH
Stone White Alcoa
Stone White FBF44SWH
Clad-TexConsolidated MetalsCopper Sales / Una-Clad / FirestoneEnglertIntegris / RyersonMetal EraPetersen / Pac-CladReynoldsValspar
Teal Alcoa
Teal FBF44T
American Buildings Co.AtasBerridgeCentriaClad-TexConsolidated MetalsCopper Sales / Una-Clad / FirestoneEnglertIntegris / RyersonMetal EraPetersen / Pac-CladVic West
Terra Cotta AEP Span
Terra Cotta FBF43TCFBF44TC
AlcoaAmerican Buildings Co.BerridgeClad-TexConsolidated MetalsCopper Sales / Una-Clad /FirestoneDMI (Dimensional Metals)Gulf StatesIntegris / RyersonMetal EraMetal SalesPetersen / Pac-CladReynoldsVic WestVP Buildings
Winter Blue Integris / Ryerson Winter Blue FBF44WBLZinc Gray AEP Span
Zinc Gray FBF44ZGYBerridgeMetal Sales
Diameter Body Mandrel Shear Tensile1/8” Steel Steel 280 4101/8” Aluminum Aluminum 150 1801/8” Stainless Stainless 520 6001/8” Copper Brass 215 3003/16” Steel Steel 600 8703/16” Aluminum Aluminum 280 4303/16” Stainless Stainless 1600 1100
Rivet Diameter Drill Bit Size 1/8” #30 3/16” #11
Use the correct drill bit to assure proper rivet performance. 1350 Split Point
Drill BitsTechnical Information
GET-A-GRIPPAINTED RIVETS | #43 & #44
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD48.0616
WEATH-R-SEAL Washers
Part Description
Aluminum BondedWeath-R-Seal Washers
.729” O.D. - .040 Aluminum
1” O.D. - .040” Aluminum
304 Stainless Steel BondedWeath-R-Seal Washers
.729” O.D. 20 gauge 304 S/S
1” O.D. 20 gauge 304 S/S
FAB-LOK®
TypeH20
PressureLengthof test Result
FAC - 10-4 100 psi 5 days No leaks
FAB-LOK®Type FAC FAS
Avg. shear 1885 lbs. 2400 lbs.
FAB-LOK® TypeFAS
Maximum 900 lbs.
Residual 860 lbs.
Clamping Force
SheetMaterial
SheetThickness
Failurelbs.*
Type ofFailure
Steel
24 ga. 833 Sheet Split
20 ga. 858 Sheet Split
18 ga. 1050 Sheet Split
16 ga. 1293 Sheet Split
14 ga. 1400 Fastener Broke
Type Fac - Single Sheet
Sheet MaterialFAB-LOK®
FAS-10-4#14 Sheet
Metal Screw
Strip test in .032” Aluminum 75 inch-lbs.* 65 inch-lbs.*
Strip test in 26 ga. Steel 75 inch-lbs.* 45 inch-lbs.*
Strip test in 24 ga. Steel 75 inch-lbs.* 55 inch-lbs.*
Comparison: FAB-LOK® & Sheet Metal SC
Fatigue TestsTwo thicknesses of 26 gauge metal fastened with FAB-LOK® and tested on 5000 lb. capacity machine at 1500 cycles per minute, sustained 1,775,500 cycles when failure of sheets occurred. Fastener did not fail.
FAB-LOK® fastening 1/8” aluminum plate to 3/16” steel of a railroad freight car, held without failure when the car was subjected to jarring vibration by a Hewitt-Robins Car Shaker at 900 cycles for ten minutes.
INFORMATION PROVIDED HERE IS BASED UPON TESTS BELIEVED TO BE RELIABLE. IN AS MUCH AS ELCO FASTENING SYSTEMS HAS NO CONTROL OVER THE EXACT MANNER IN WHICH OTHERS MAY USE THIS INFORMATION, IT DOES NOT GUARANTEE THE RESULTS TO BE OBTAINED NOR DOES THE COMPANY MAKE ANY EXPRESS OR IMPLIED WARRANTY OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE CONCERNING THE EFFECTS OR RESULTS OF SUCH USE.
FAB-LOK® fasteners were designed to maintain panel integrity in high-stress environments such as: high wind areas, expansion and contraction, severe vibration, racking and the repair of oversized holes.
Pull-out tests were performed on a Model L Dillon Dynamometer. FAB-LOK® fasteners were installed in single sheet and two sheets of metal and pulled over the tines of the FAB-LOK® to determined holding values.
Vibration, either from inside or outside a building, can make ordinary fasteners loosen and back out.
FAB-LOK® fasteners combine a slotted aluminum sleeve and fastener to provide the simplicity and strength of both elements.
Material SizePenetratingLength Grip Range
Wt. / M
Carbon Steel
FAS 10-4 1.373” .062”-.250” 23
FAS 10-8 1.612” .250”-.500” 24
FAS10-12 1.807” .500”-.750” 28
H-3 (300 series)Stainless Steel
FAC10-4 1.373” .062”-.250” 23
FAC 10-8 1.612” .250”-.500” 24
FAC 10-12 1.807” .500”-.750” 28
Sizes
FAB-LOK®
Technical Information
Single Shear Strength
Hydrostatic Test
Installation1. Predrill with a 5/16" diameter drill bit2. Insert FABLOK into hole. Use the FABLOK holding sleeve with a DEWALT screw-gun (DW268 or DW267)
Holding Sleevep.n. : EZL900
FAB-LOK RIVETS
36
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD49.0616
SIDE-LAP & END-LAP FASTENERS FOR COMPOSITE TYPE PANELS & SKYLIGHTS
Grommet Seal Fasteners are compression fasteners used in side-lap applications which utilize fiberglass, plastic or composite sheeting.
The grommet is installed by placing it into a pre-drilled 1/4” or 3/8” hole and tightened using a screw gun with a standard 1/4” or 5/16” socket. The machine screw engages the nut insert, forcing the sleeve to expand against the inner wall of the materials. Grommets become an excellent sealant against air, moisture and vibration.
Grommet Size 1/4” x 1” 3/8” x 1”
Body Length .948 .812
Nut Insert 6-32 10-32
Durometer (sleeve) 70 60
Ultimate Tensile 50 lbs. 80 lbs.
Machine Screw Size 6-32” x 1” 10-32” x 1”
Hex Size 1/4” 5/16”
Material 302 HQ 302 HQ
Bonded Washer 304 SS/EPDM 304 SS/EPDM
Sleeve EPDM EPDM
Nut Insert Brass Brass
Recommended
Hole Size .250 .375
Grip Range .375-.607 .312-.450
*Also available in 316 stainless steel.
SizesandSpecifications
Installation
BULB-TITE®
The standard Bulb-Tite® rivets are made of aluminum alloy, providing a durable non-rusting fastener that can withstand weather-related corrosion.
Bulb-Tite® Rivets handle your attaching problems with ease.
Tools designed to install Bulb-Tite® Rivets in metal clad building application.
Contact TFC for availability!
More than forty years ago the first Bulb-Tite® was developed to solve application requirements in the Pre-Engineered Metal Building industry. Since that time the Bulb-Tite® product line has been expanded to meet application requirements in a wide range of industries.
The Bulb-Tite® rivet body folds into three separate legs forming a large blind-side head. This large bearing head evenly distributes the Bulb-Tite® high clamp force in soft, thin or brittle materials while providing high pull through resistance. The Bulb-Tite® wide grip range enables a single Bulb-Tite® to work in a greater variation of thickness. Some versions of the Bulb-Tite® feature a special flush break mandrel that effectively seals the rivet bore and adds greater shear strength.
ToolsSizes TFC Part Number
A 3/16" x 1/4" RV6604-6-4W
B 1/4" x 3/8" RV6604-8-6W
C 9/32" x 3/8" RV6603-9-6W
D 9/32" x 3/8" Flange RV6605-9-6W
Sizes
*Available with washer
A
B
C
D
GROMMET SEAL AND BULB-TITE RIVETS
37
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD166.0616
See why BRACER® LITE provides better performance compared to standard hillside washers.
INDEPENDENT TESTSTFC is the only supplier of hillside style washers that can supply independent tests to confirm the load capacities.
ANTI SLIP SERRATIONSOur patented serrations reduce rod slippage, which keep the bracing from becoming loose.
LARGER NIPPLEDesigned to engage the web slot deeper, making installation easy and producing greater loads in applications requiring steep rod angles.
Material: Ductile Iron ASTM 536-84 Grade 64-45-12Finish: Plain
WEBBRACER LITE
SIZELOAD
(Ultimate)
1/8” 1/2” (1)10,750 lbs.
1/8” 5/8” (1)15,850 lbs.
3/16” 3/4” (2)23,500 lbs.
1/4” 3/4” (2)26,600 lbs
LOAD RESULTSIndependent tests were conducted at Mississippi State University under the direction of Dr. Ralph Sinno Ph.D. P.E. in accordance to test sponsored by the MBMA and published as part of the Journal of Structural Engineering Vol 119, No 11, November 1993, “X-Bracing Anchorage Connection” paper.
Comments by Dr. Ralph Sinno:“Triangle Fasteners “Bracer Lite” hillside anchors having ridges, serration, on the curvature of the hillside washer with companion Stress-Lok washers were found to be superior to the standard off-the-shelf market available ductile steel hillside washers. They carry higher loads with no failure in any tests to neither the hillside anchor, “Bracer Lite”, nor the Stress-Lok washers.”
STRESS-LOK® WASHEROur patented STRESS-LOK® clamping washer distributes the load across more area than a standard flat washer.
BRACER® LITE
HILLSIDE STYLE WASHER
BRACER® LITE increases load capacities and performance compared to ordinary hillside washers. Included with BRACER® LITE is our STRESS-LOK® clamping washer that increases the load carrying capacities and reduces slippage of the rod, keeping the bracing tight!
Improve the performance over standard hillside washers...Specify BRACER® LITE
Available in 3 sizes!1/2" 5/8" 3/4"
Tests conclude that this design increases the load capacity of the bracing assembly, keeping the rod from slipping across the surface which can cause loosening of the nut.
Tests conclude that the patented BRACER® LITE with STRESS-LOK® were found to be superior to off the shelf hillside washers, and can carry higher loads.
TECHNICAL INFORMATION
Independent tests confirm that BRACER® LITE produced from ductile iron produces higher load capacities and better ductility. Hillside washers produced from Class 30 cast iron had unpredictable load capacities.
Rod Angle: (1) 300 / (2) 450
Failure ModeRod tensile failure.
BRACERBRACING WASHER LITE®
38
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD165.0616
BRACER® Rod
Base Dimension
Length Width
#1 (Oval) 5/8” 4.000” 3.000”
#2 7/8" 4.000" 3.000"
#3 1-1/4" 4.000" 3.000"
#4 1-1/2" 4.250" 3.000"
BRACER® HILLSIDE STYLE WASHER
BRACER® Base Dimensions
The BRACER® with slip resistant knurls was designed to increase the load capacity of your bracing system by over three times more than a standard hillside washer.
Our patented slip resistance knurls minimizes slippage of the rod, keeping the bracing tight. It has been tested by an independent laboratory confirming that BRACER® achieves complete loading of the web and rod, eliminating backup plates and welding! This research provides the only certified load data by any supplier of hillside style washers.
The first hillside washer that eliminated back-up plates! BRACERBRACING WASHER
R
• Patented knurls on the surface minimizes slippage of the rod.
• Eliminates back-up plates and welding.
• Special nipple is design to engage the web slot deeper, producing higher load capacity and easy installation!
• Made from high strength ductile iron to assure quality performance.
• Certified independent test data confirms load capacities.
WHY BRACER® ? Patented design provides optimal load transfer and easy installation.
SIZES AND ROD CAPABILITY
US Patent # 6,217,270
MATERIAL PROPERTIES
FINISHRed Enamel: BRACER #1,2,3Gray Enamel: BRACER #4Type: gloss enamel, 85 units minimum at 60°.Thickness: 1.6-2.0 milsAdhesion: ASTM 2794 Excellent. No Peeling or removalImpact Resistance: ASTM D 2794 Good > 10 in. lbs.Abrasion Resistance: ASTM D 4060 GoodCorrosion Resistance: Salt Spray: 250 hrs. (<5% red rust) Kesternich: 5 cycles (<10% red rust)OPTIONAL FINISHHot Dip Galvanized Per ASTM 153 Class A
STANDARD MATERIAL (Import & Domestic)Ductile IronASTM 536-84 Grade 65-45-12Ultimate Tensile Strength: 65,000 PSI
For load data, please refer to
page 208.
Need a standard hillside?Call about information on our BRACER LITE!
The elliptical Shape of the #1 BRACER® distributes stress into web for better load distribution!
ROD AND(BRACER SIZE)
ROD ANGLE (MAX)
FROM MSU TESTSLOT WIDTH (W)
MINIMUM*SLOT
LENGTH(L)
*SLOT WIDTH
(W)DUCTILE
IRON
1/2” Rod(#1 BRACER) 550 2.125" 1.062” .750”
5/8” Rod(#1 BRACER) 520 2.125" 1.062” .750”
3/4” Rod (#2 BRACER) 550 2.125" 1.062” 1.000”
7/8” Rod(#2 BRACER) 520 2.125" 1.062” 1.000”
1” Rod (#3 BRACER) 580 2.625" 1.312” 1.250”
1-1/4” Rod (#3 BRACER) 560 2.625" 1.312” 1.312”
1-3/8” Rod (#4 BRACER) 550 3.500" 1.625” 1.425”
1-1/2” Rod(#4 BRACER) 520 3.500" 1.625” 1.600”
SlOT REquIREmENTS - mINImumSlots in the web must be sized to allow a rod angle of up to 520 and to allow the tab on the bottom of the BRACER® to engage the web.
*Static load tests were conducted using the these dimensions.
L
W
SLOT SIZES AND ROD ANGLES#1 BRACER®Oval With Knurls(1/2" - 5/8" Rod)
#2 BRACER®With Knurls
(3/4"- 7/8" Rod)
#3 BRACER®(1" - 1-1/4" Rod)
#4 BRACER®(1-3/8" - 1-1/2" Rod)
Shown in standard red paint and optional HDG finish.
Statement of certification by Dr. Ralph Sinno Ph.D. Professor of Civil Engineering Mississippi State University.
"The #1 BRACER® ductile iron oval hillside washers for 1/2 - 5/8" rods surpass the design capacity of the rods and beam / column sections."
"Procedures and calculations in the literature for the design of x-bracing anchorage can be used with confidence when specifying and selecting ductile iron oval BRACER® hillside washers."
"The oval shape is better than rectangular mainly because of two reasons: The base area is almost the same and the oval shape eliminated stress concentrations at the 90-degree corners and reduces the cantilever distance (from the corner of the base to the center of the rod). In addition, your oval shape is properly stiffened on it's back. This latest oval shape is a winner with STRESS-LOK!
REV. JS010916
MADE IN USA AVAILABLE
39
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD167.0616
STRESS-LOK™ CLAMPING WASHER
STRESS-LOK® is the first washer designed to keep brace rods tight. It eliminates slippage of the rod caused by vibration due to wind load, earthquakes, cranes and other cyclic loads.
The concave bearing surface with a series of knurls, increases the contact area between the washer and hillside. The additional contact area distributes the load over a greater area, thereby keeping the connection tight. It also improves the overall strength of a standard hillside washer.
SpecificallyDesignedforUseWithBracingWashers
For optimal performance of your bracing system, use STRESS-LOK with BRACER Hillside Style Washers.
STRESS-LOK can be use with ordinary hillside washers to improve their performance.
For load data, please refer to page 208.
• The curved mating surface increases performance by distributing the load onto the hillside.
• The increased contact area eliminates slippage that can loosen the connection.
• Certified independent test data confirms load capacities.
• Can be used with standard hillside washers to improve their performance.
Patented washer distributes the bracing load across the hillside to increase strength and reduce slippage of the rod.
WHY STRESS-LOK ®?
Flat washers provide minimal contact which can weaken the
connection and cause loosening of the nut.
STRESS-LOK® distributes the load over a greater area which increases strength
compared to standard flat washers.
INDEPENDENT TESTS
STRESS-LOKCLAMPING WASHER
R
US Patent # 6,217,270
1/2” Rod
SIZES (Rod Size): 1/2”, 5/8” and 3/4”MATERIAL: Low Carbon SteelFINISH: .0003” min. Zinc Plated
SIZES AND DIMENSIONS
5/8” Rod 3/4” Rod
“...Triangle Fastener’s hillside anchors having ridges, serration, on the curvature of the standard hillside washer with Stress-Lok washers were found to be superior to the standard off-the-self market available hillside washers.”
Source: R. Ralph Sinno, Ph.D., P.E., F. ASCE Professor of Civil & Environmental Engineering
Statement from independent laboratory tests conducted at Mississippi State University, August 26, 2008.
Increase the stability of your building for
less than $0.50 per rod!
40
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD163.0616
DANDI-EYE FORGED EYEBOLTS
DANDI-EYE Sizes 6” Thread Length Eye Opening
Min. Tensile Strength
(lbs.)Recommend
Grip SizeMin. EHS Cable Strength (lbs)
1/2-13 x 8” 1-1/2” 8,500 lbs. 1/4” 6,6505/8-11 x 8” 1-1/2” 13,600 lbs. 5/16” 11,2003/4-10 x 8 1-1/2” 20,000 lbs. 3/8” 15,4007/8-9 x 8” 1-1/2” 27,700 lbs. 1/2” 26,900
DANDI-EYEBRACING SYSTEM EYEBOLT
• Meets ASCE 19-96 Standards for Structural Applications of Steel Cables for Buildings.
• Supplied with harden washers and nut. STRESS-LOK Clamping washer available for added strength.
• Shipped with material certifications when required.
Forged Eye-bolts designed to exceed the strength of
the EHS bracing cable
PROPERTIESMaterial: Carbon steel (Grade 1)Finish: .0003” zinc plated with clear chromate.
SIZES | STRENGTHS
We provide BRACER® hillside washers for use with cable or rod bracing systems up to 1-1/2” diameter. BRACER® is independently tested to confirm the load capacities. Contact TFC for more information.
END FITTINGS
41
CR
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD299.0616
A FAST AND EASY WAY TO ATTACH 600LF OF STEEL BASE ANGLE TO
CONCRETE FLOORSOur heavy duty threaded concrete screw secures the base angle tighter and holds the base better than ordinary powder actuated pins or nail-in zinc anchors.
Description Qty5/16” x 1-3/4” Threaded Concrete Screws 200
¼” x 4” Carbide Tip Drill Bit (Drilling concrete) 25/16” Stubby 1350 Split Point Drill Bit (Drilling steel base angle) 3
5/16” Across Flats Hex Magnetic Nut-setter (Use to install the screw) 1
KIT INCLUDES
TYPICAL APPLICATION
• A 5/16” diameter threaded concrete screw is easy to install and stays tight and secure.
• Our large diameter washer face increases pullover strength and increases resistance to back-out compared to nails or hammer driven anchors.
• Our screw is long-life coated for superior corrosion resistance
BASE ANGLE ATTACHMENT KIT
Please contact TFC for your specific needs.
FASTENER SPECIFICATIONS
Size Material Finish Head StyleWasher
Diameter
5/16” x 1-3/4” Carbon Steel Long-life coated / 800 hour salt spray per ASTM B117 5/16” Across Flats .545”
PULL-OUT AND SHEAR VALUES
AnchorDiameter
Depth of Embedment
Concrete(3,513 p.s.i.)
Pull-out Shear5/16” 1-3/4” 2643 3404
DISCLAIMER: ALL TEST RESULTS AND SPECIFICATIONS ARE A RESULT OF LABORATORY TESTS. APPROPRIATE SAFETY FACTORS SHOULD BE USED BY THE USER OR SPECIFIER. DETERMINING THE PROPER FASTENER IS THE RESPONSIBILITY OF THE USER OR SPECIFIER. SINCE APPLICATION CONDITIONS VARY AND ARE UNCONTROLLABLE BY TFC, WE ASSUME NO LIABILITY FOR THE USE OF THIS INFORMATION.
Everything you will need to install 600 lineal feet of base angle.(Based on fastening every 3 feet)
Physical Properties
Performance
Great for new and retrofit applications
Another New TFC Specific Fastening System Solution!
42
CR
TRIANGLE FASTENERCORPORATION
800.486.1832 | www.trianglefastener.comMD290.0616
TFC PRODUCTQUICK FACTS
800.486.1832
Visit our websitefor the most up-to-date product
and technical information!
ww.trianglefastener.com
ATTACH TO CONCRETE, BRICK, OR BLOCK CONCRETE ANCHORS
THREADED CONCRETE SCREWS
HAMMER-IN ANCHORS
EXPANSION ANCHORS
CHEMICAL / EPOXY ANCHORS
POWDER AND GAS CHARGED CONCRETE PINS AND TOOLS
THREADED SCREWSMost popular for a variety of applications.Carbon Steel or Stainless Steel
Diameters: 3/16", 1/4", 3/8", 1/2", 5/8", 3/4"
Lengths: Up to 6"
HAMMER-IN ANCHORSZAMAC or SPIKESZinc Alloy, Carbon Steel or Stainless Steel
DiametersZAMAC: 1/4"SPIKES: 1/4", 3/8", 1/2"
Lengths: Up to 14"
EXPANSION ANCHORSSleeve, Wedge, or Drop-inCarbon Steel or Stainless Steel
Diameters: 1/4", 3/8", 1/2", 5/8", 3/4", 7/8", 1", 1-1/4"
Lengths: Up to 12"
CHEMICAL ANCHORSRED HEAD EPCON Brand
Use in a variety of applications
PINS, LOADS, TOOLSRAMSET® Brand pins and loadsVariety of powder actuated and gas charged pins, loads and tools
43
CR
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD151.0616
C-90 Hollow Block Red Solid Block Anchor Size Embed. Depth Tension (lbs) Shear (lbs.) Tension (lbs) Shear (lbs.) 3/16" 3/4" 270 860 460 920 1/4 “ 5/8" 360 1040 570 1250 1/4 “ 3/4" 480 1160 790 1400 1/4 “ 1" 590 1320 820 1400 1/4 “ 1 3/8" 800 1320 950 1400 1/4 “ 1 1/2" 965 1320 1015 1400
2,000 PSI Concrete 4,000 PSI Concrete 6,000 PSI Concrete Anchor Size Embed. Depth Tension (lbs) Shear (lbs.) Tension (lbs) Shear (lbs.) Tension (lbs) Shear (lbs.) 1/4 “ 5/8" 480 1230 600 1500 640 1500 1/4 “ 3/4" 580 1230 720 1500 760 1500 1/4 “ 7/8" 770 1350 820 1500 890 1500 1/4 “ 1 1/8" 890 1400 960 1500 1060 1500 1/4 “ 1 3/8" 980 1400 1150 1500 1230 1500 1/4 “ 1 7/8" 1150 1400 1300 1500 1365 1500
The TFC ZAMACTM is a tamper-proof nail drive anchor which has a body formed from Zamac alloy. Nails are available in carbon or stainless steel. The anchor can be used in concrete, block, brick or stone. This anchor is not recommended for applications overhead.
Base Material: Concrete, Block, Brick, StoneSize Range: 3/16" x 7/8" to 1/4" x 2"Anchor Material: Zamac Alloy with Carbon or Stainless Steel Drive Pin
Drill Std. Std. Size Dia. Box Ctn. 1/4" x 3/4" 1/4" 100 500 1/4" x 1" 1/4" 100 500 1/4" x 1-1/4" 1/4" 100 500 1/4" x 1-1/2" 1/4" 100 500 1/4" x 2" 1/4" 100 500
Mushroom Head Zamac Nailin® Carbon Steel Nail
Drill Std. Std. Size Dia. Box Ctn. 1/4" x 1" 1/4" 100 500 1/4" x 1-1/4" 1/4" 100 500 1/4" x 1-1/2" 1/4" 100 500 1/4" x 2" 1/4" 100 500
Mushroom Head Zamac Nailin® Type 304 Stainless Steel Nail
Drill Std. Std. Size Dia. Box Ctn. 1/4" x 1-1/2" 1/4" 100 500 1/4" x 2" 1/4" 100 500
Flat Head Zamac Nailin® Carbon Steel Nail
ZAMAC™Drive Pin Anchor
Performance DataThe following ultimate load capacities are based on tests conducted according to ASTM Standard E 488.
Ultimate Load Capacities - C-90 Hollow Block and Red Solid Block
ZAMAC DRIVE PIN TYPE ANCHORS
44
CR
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD138.0616
Trubolt Wedge Anchors Performance Table Ultimate Tension and Shear Values (Lbs/kN) In Concrete*
Anchor Installation Embedment f’c = 2000 PSI (13.8 MPa) f’c = 4000 PSI (27.6 MPa) f’c = 6000 PSI (41.4 MPa) Dia. Torque Depth Anchor Tension Shear Tension Shear Tension Shear In. (mm) Ft. Lbs. (Nm) In. (mm) Type Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)1/4 (6.4) 8 (10.8) 1-1/8 (28.6) 1,180 (5.2) 1,400 (6.2) 1,780 (7.9) 1,400 (6.2) 1,900 (8.5) 1,400 (6.2) 1-15/16 (49.2) 2,100 (9.3) 1,680 (7.5) 3,300 (14.7) 1.680 (7.5) 3,300 (14.7) 1,680 (7.5) 2-1/8 (54.0) 2,260 (10.1) 3,300 (14.7) 3,300 (14.7)
3/8 (9.5) 25 (33.9) 1-1/2 (38.1) 1,680 (7.5) 2,320 (10.3) 2,240 (10.0) 2,620 (11.7) 2,840 (12.6) 3,160 (14.1) 3 (76.2) 3,480 (15.5) 4,000 (17.8) 5,940 (26.4) 4,140 (18.4) 6,120 (27.2) 4,500 (20.0) 4 (101.6) 4,800 (21.4) 5,940 (26.4) 6,120 (27.2)
1/2 (12.7) 55 (74.6) 2-1/4 (57.2) 4,660 (20.7) 4.760 (21.2) 5,100 (22.7) 4,760 (21.2) 7,040 (31.3) 7,040 (31.3) 4-1/8 (104.8) 4,660 (20.7) 7,240 (32.2) 9,640 (42.9) 7,240 (32.2) 10,820 (48.1) 8,160 (36.3) 6 (152.4) 5,340 (23.8) 9,640 (42.9) 10,820 (48.1)
5/8 (15.9) 90 (122.0) 2-3/4 (69.9) 6,580 (29.3) 7,121 (31.7) 7,180 (31.9) 7,120 (31.7) 9,720 (43.2) 9,616 (42.8) 5-1/8 (130.2) 6,580 (29.3) 9,600 (42.7) 14,920 (66.4) 11,900(52.9) 16,380(72.9) 12,520(55.7) 7-1/2 (190.5) 7,060 (31.4) 15,020 (66.8) 16,380 (72.9)
3/4 (19.1) 175 (237.3) 3-1/4(82.6) 7,120 (31.7) 10,120 (45.0) 10,840 (48.2) 13,720 (61.0) 13,300 (59.2) 15,980 (71.1) 6-5/8 (168.3) 10,980 (48.8) 20,320 (90.4) 17,700 (78.7) 23,740 (105.6) 20,260 (90.1) 23,740 (105.6) 10 (254.0) 10,980 (48.8) 17,880 (79.5) 23,580 (104.9)
7/8 (22.2) 250 (339.0) 3-3/4 (95.3) 9,520 (42.3) 13,160 (58.5) 14,740 (65.6) 16,580 (73.8) 17,420 (77.5) 19,160 (85.2) 6-1/4 (158.8) 14,660 (65.2) 20,880 (92.9) 20,940 (93.1) 28,800 (128.1) 24,360 (108.4) 28,800 (128.1) 8 (203.2) 14,660 (65.2) 20,940 (93.1) 24,360 (108.4)
1 (25.4) 300 (406.7) 4-1/2 (114.3) 13,940 (62.0) 16,080 (71.5) 20,180 (89.8) 22,820 (101.5) 21,180 (94.2) 24,480 (108.9) 7-3/8 (187.3) 14,600 (64.9) 28,680 (127.6) 23,980 (106.7) 37,940 (168.8) 33,260 (148.0) 38,080 (169.4) 9-1/2 (241.3) 18,700 (83.2) 26,540 (118.1) 33,260 (148.0)
1-1/4 (31.8) 500 (677.9) 5-1/2 (139.7) 18,140 (80.7) 23,280 103.6) 26,380 (117.3) 29,460 (131.0) 33,640 (149.6) 33,780 (150.3) 8 (203.2) 27,340 (121.6) 35,080 (156.0) 43,300 (192.6) 44,260 (196.9) 45,540 (202.6) 50,560 (224.9)
* Allowable values are based upon a 4 to 1 safety factor. Divide by 4 for allowable load values.
Carbon Steel With Zinc
Plating
or
Carbon Steel With
Hot-Dipped Galvanizing
or
Type 304 Stainless
Steel
or
Type 316 Stainless
Steel
Lower Flute Of Steel Deck with Lightweight Concrete Lightweight Concrete Fill Anchor Installation Embedment f’c = 3000 PSI (20.7 MPa) f’c = 3000 PSI (20.7 MPa) DIA. Torque Depth Anchor Tension Shear Tension ShearIn. (mm) Ft. Lbs. (Nm) In. (mm) Type Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)3/8 (9.5) 25 (33.9) 1-1/2 (38.1) 2,120 (9.4) 3,720 (16.5) 1,900 (8.5) 3,160 (14.1) 3 (76.2) 2,940 (13.1) 4,240 (18.9) 2,840 (12.6) 4,000 (17.8)
1/2 (12.7) 55 (74.6) 2-1/4 (57.2) 3,600 (16.0) 7,040 (31.3) 3,400 (15.1) 5,380 (23.9) 3 (76.2) 4,720 (21.0) 6,620 (29.4) 4,480 (19.9) 6,620 (29.4) 4 (101.6) -- -- 6,920 (30.8) 4,800 (21.4) 6,440 (28.6)
5/8 (15.9) 90 (122.0) 3 (76.2) 6,000 (26.7) 9,240 (41.1) 4,720 (21.0) 5,500 (24.5) 5 (127.0) 5,960 (26.5) 9,280 (41.3) 6,580 (29.3) 9,140 (40.7)
3/4 (19.1) 175 (237.3) 3-1/4 (82.6) 7,160 (31.9) 12,600 (56.0) 5,840 (26.0) 8,880 (39.5) 5-1/4 (133.4) 8,900 (39.6) 15,920 (70.8) 7,040 (31.3) -- --
* Allowable values are based upon a 4 to 1 safety factor. Divide by 4 for allowable load values.
Carbon Steel With Zinc Plating or
Carbon Steel With Hot-Dipped
Galvanizing or Type 304 Stainless Steel or Type 316
Stainless Steel
Trubolt Wedge Anchors Performance Table Ultimate Tension and Shear Values (Lbs/kN) In Lightweight Concrete*
Technical Data
Trubolt® Wedge AnchorsDependable, Heavy-Duty, Inspectable, Wedge Type Expansion Anchor
DYNABOLT® WEDGE ANCHORS
45
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD203.0616
• Flexible, weather resistant EPDM rubber or silicone.
• Aluminum base is flexible to conform to any panel profile
• Grey EPDM is ozone and ultraviolet resistant
Note: #1 and #3 are closed top. When flashing a steep pitch roof greater than 20° or a profile with a rib height of 1-1/2" or more, use the next larger flashing for increased flexibility. Fastening Recommendation
Corrosion resistant fasteners should be used around the base one every 1-1/2 inches as per the United Plumbing Code (UPC) recommendations. Refer to size chart for the quantity to use.
Fastener1/4-14 x 1-1/8" DP1 BLAZER Stainless Cap Head with VRT Technology
Sealant RecommendationUltra 1000® or APS 500 sealant should be used under the base to assure a proper seal. If you prefer, additional sealant can be applied around base after installation.
PIPE-MASTER PIPE FLASHING
Pipe Size Outside Diameter
Flash Number Flashing Details
TFC Part Number
Number of Fasteners
1/4" - 2 1/2" EPDM #1Top Opening Diameter: Closed
Overall Height:: 2.77"Base Diameter: 4.75"
001DEKR 10
1 3/4" - 3" EPDM #2Top Opening Diameter: 1.44"
Overall Height: 3.53"Base Diameter: 6.21"
002DEKR 13
1/4" - 5" EPDM *Silicone #3
Top Opening Diameter: ClosedOverall Height: 3.64"Base Diameter: 7.74"
003DEKR003DEKS
1616
3" - 6 1/4" EPDM #4Top Opening Diameter: 2.38"
Overall Height: 5.05"Base Diameter: 9.26"
004DEKR 19
4 1/4" - 7 3/4" EPDM *Silicone #5
Top Opening Diameter: 3.50"Overall Height: 4.43"
Base Diameter: 10.75"
005DEKR005DEKS
2222
5" - 9" EPDM #6Top Opening Diameter: 4.25"
Overall Height: 5.60"Base Diameter: 12.50"
006DEKR 26
6" - 11" EPDM #7Top Opening Diameter: 4.90"
Overall Height: 5.84"Base Diameter: 14.60"
007DEKR 30
7" - 13" EPDM *Silicone #8
Top Opening Diameter: 5.80"Overall Height: 7.53"Base Diameter: 16.5"
008DEKR008DEKS
3535
9" - 19" EPDM *Silicone #9
Top Opening Diameter: 7.45"Overall Height: 8.09"
Base Diameter: 25.25"
009DEKR009DEKS
5454
15" - 24" EPDM *Silicone #10 Pipe Size: 15"-24" Diameter
(Square Base only)010DEKR010DEKS 148
Standard Applications
EPDM SiliconeAdvanced Ozone Resistance 70 hours @ 500 pphm 70 hours @ 500 pphm
High Temperature ResistanceIntermittent +135˚ C (275˚ F) +260˚C (+500˚ F)
Continuous +100˚C (212˚ F) +225˚ C (+437˚ F)
Low Temperature Resistance -55°C (65°F) -74°C (-100°F)Tensile Strength (min) 10 MPa (1450 psi) 5 MOPa (700 psi)
Compression Set (max) 25% 50%
Material Specifications
PIPE-MASTER™ RETROUse in retrofit applicationsGray or Black EPDM and Silicone
Available in nine colors to match your roof!Sizes#3 - Pipe diameter 1/4" to 4"#5 - Pipe diameter 4" to 7"
Material: EPDM
PIPE SIZE US PART NUM FLASHING DETAILS #1 3/4”- 2-3/4” Black RF 101 BS Opening diameter 3/4” Gray RF 101 GS Pipe size 3/4”- 2-3/4” Silicone RF 102 RD Base dimensions 6 -3/10” #2 2”- 7-1/4” Black RF 201 BS Opening diameter 2” Gray RF 201 GS Pipe size 2” - 7 -1/4” Silicone RF 202 RD Base dimensions 10 -3/4” #3 3-1/4” -10” Black RF 301 BS Opening diameter 3 -1/4” Gray RF 301 GS Pipe size 3 -1/4” – 10” Silicone RF 302 RD Base dimensions 14 -1/2”
46
CR
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD205.0616
PIPE FLASHING35 YEAR WARRANTY
47
CR
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD209.0616
END CAP FLASHING FOR METAL ROOF SYSTEMS
48
800.486.1832 | www.trianglefastener.com
CR
TRIANGLE FASTENERCORPORATION
TFC PRODUCTQUICK FACTS
800.486.1832
Visit our websitefor the most up-to-date product
and technical information!
ww.trianglefastener.com
MD269.0616
BUTYL-TAPE SEAL™ PIPEMASTER® Pipe Flashing
Universal Closure Seal
Underlayments
CLOSE-TITE™ Foam Closure Expandable Edge Flashing
Ridge Venting Material
BUTYL-TAPE SEAL Sticks to a variety of materials including: painted metal & Kynar & siliconized polyester. SIZES: 3/32” x 3/8,” 1/2”, 1”
1/2” x 1” 3/16” x 7/8”
PIPEMASTER® FlEXIblE PIPE FlASHINg
• EPDM and Silicone material.
• Flash up to 24” diameter pipe.
• Available in colors.
• 35 year warranty.
RIDGE VENTING MATERIALVersa Vent ridge venting material design for R-Panel and M-Panels.
UNDERLAYMENTSWe can provide high performance name brand underlayments.
CLOSE- TITE®
FOAm ClOSuRESAvailable in wide variety of profiles to match your panel.
EXPANDABLE EDGE FLASHING
• EPDM material
• Widths of 7”, 9”, 12”, and 18”
UNIVERSAL CLOSURE SEAL• Open cell foam impregnated
with acrylic modified asphalt emulsion.
• Material expands to fill voids. SIZES: 1/4” x 1/2”, 1” 5/16” x 3/4” 1/2” x 1” (Expands from 3/4” to 1-1/2” depending on original thickness).
OUR SEALANTS ARE DESIGNED FOR LONG TERM DURABILITY AND PERFORMANCE
SEALANTS
49
NOTE: Colors listed do not represent actual colors. Contact your local distributor for the ULTRA1000® color selector swatches for accurate color match.
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD213.0616
•Silicone sealant provides exceptional weatherability
•Class 50 for superior movement capability
•Adheres to Kynar® and Galvalume® coated metals
•VOC compliant•Mildew resistant• "Guns" down to 0°F•Service temperature -40°F
to +400°F•Tack free in 10 minutes
ULTRACLASS 50 | SILICONE SEALANT
1000™
Concerned about sealant failure caused by joint movement? Specify ULTRA1000™ Class 50 Silicone Sealant. It is formulated to withstand 2x more joint movement than ordinary Class 25 sealants.
20 Colors! Call for availability. *Denotes in stock colors
*Sierra TanBG154
*Slate GrayGY192
*BlackBLK110
*Charcoal GrayGY195
*BrownBR121
*Hartford GreenGR160
* Gutter GrayGY196
*Dark BronzeBZ131
*GreenGR164
*TranslucentTR99
Hemlock GreenGR161
*RedRD141
*Antique WhiteWH102
*AlmondBG151
*Electric BlueBL182
*White WH100
Regal RedRD143
*Regal BlueBL181
Applications• Flashing• Trim• Metal Sheeting• Downspouts • Gutters• Roof Tile• Flashings• Adheres to Copper
Bonds To
Steel
Aluminum
Brick
PVC
Glass
Concrete
Formulated for Superior Performance
Never misplace another nozzle! Tubes are now packaged with nozzle!
Packaging
We've redesigned the packaging so that the plastic screw-on nozzles come pre-assembled on the tubes.
Class 50 sealant provides 50% extension and 50% compression of the width of the joint.
*SandstoneBG152
*Light GrayGY190
*Off WhiteWH104
50
Limited Warranty: Satisfaction guaranteed when handled and applied according to label.
Product Specifications
APS 500 is formulated to provide superior adhesion, excellent resistance to weathering and is compatible for use with a variety of substrates. Supplied in plastic tubes with screw-on nozzles. Available in smooth or textured finish.
Over 24 Colors Available!*Denotes standard colors.
*The values outlines reflect testing that was conducted on laboratory prepared specimens, actual results may vary. The information provided in the above table is not intended for use in preparing specifications. Please consult manufacturer for additional information.
Physical Property Test Method Typical ValueTensile Strength ASTM D412 205 psi
Elongation ASTM D412 650%
Shore Hardness ASTM D 2240 25 +/- 5
Service Temperature -75ºF to +300ºF
Join Sealant Designation ASTM C920 Type S, Grade NS, Class 50, use T, NT, G, M
1Adhesion and Cohesion ASTM C719 Pass on glass, aluminum and concrete for +/- 50% movement
1Adhesion-in-Peel, 2 inches/minute @ 25ºC, N (lbf) ASTM C794
Aluminum 37pliGlass 35pliConcrete 34pli
Staining ASTM D2203 None
Lap Shear ASTM 961-06 190 psi
VOC EPA Method 18 9 g/L (0.14%)
Low Temp. Flexibility ASTM C 711 Pass -10 deg. F. ¼ inch mandrel
High Temp. Flexibility Industrial Method Up to 425 deg. F for short periods
Cure Rate Industrial Method 1/4” Bead per 24 Hrs
Skin Time Cure Time Industrial Method
40° F at 40% humidity 40 minutes 2 - 3 days75° F at 50% humidity 10 minutes < 24 hours
95° F at 95% humidity 5 minutes
™APS 500ADVANCED POLYMER SEALANT
• Paintable
• VOC Compliant • Fast Curing • Installs at -35°F to +140°F• Non-Yellowing
Performance
•Window Trim•Doors & Skylights •Siding•Metal Architecture•Curtain Walls & Joints•Coated Metal Roofs
Applications
Steel Brick
Aluminum PVC
GlassConcrete
JS022516
Bonds To
Do you need a custom color? We can matchyourspecificneeds!
Distributed by: TRIANGLE FASTENER CORPORATION
150*Tan
151*Almond
154Sierra Tan
120Brown
130*Dark Bronze
131*Medium Bronze
110*Black
160*Hunter Green
164Green
161Hemlock Green
162*Patina Green
193Dark Slate Gray
182Electric Blue
181Regal Blue
190*Limestone
191*Aluminum Gray
192Slate Gray
142Terra Cotta
195Charcoal Gray
145Redwood
140Burgundy
141Colonial Red
143Regal Red
196*Gray
100*White
104*Off-White
102Antique White
152Sandstone
170*Stone
98Crystal Clear
Adheres to Kynar, Galvanize, Glavalume, Copper, Stainless Steel, Zinc
NOTE: Colors listed do not represent actual colors. Contact your local distributor for the APS500® color selector swatches for accurate color match.
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD215.0616
51
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD293.0516
TFC BUTYL™ is a single component, non-skinning butyl-based solvent release sealant. It is designed to deliver excellent adhesion to metal panels while remaining permanently pliable.
The product is the ideal choice in applications where the combination of moisture and cold temperatures would cause the break-down of other sealants.
TFC BUTYLNON-SKINNING • PREMIUM GRADE
PERFORMANCE•Non-Skinning•Non-Staining•Permanently Pliable•Moisture Resistant•Non-Paintable
APPLICATIONS•MetalRoofing• Insulated Metal Panels•Use on Painted Metal,
Kynar®, Galvalume® & Galvanized Steel, Aluminum
Developed for the metal roofing industry and provides long-life performance!
SPECIFICATIONS: Meets or exceeds AAMA 809.2
COLORS: Gray (Item Number TFCNSBGY)
White (Item Number TFCNSBWH)
SURFACE PREPARATIONS: For best results, the substrate should be clean, dry, frost free, sound and free of any oils, greases or incompatible sealers, paints or coatings that may interfere with adhesion. Do not apply if surface is contaminated. It is recommended to test all substrates prior to applications.
INSTALLATION: Cut nozzle to desired bead size. Apply with caulking gun, forcing sealant onto the substrate, then tool if needed. Clean excess material with mineral spirits or similar solvent.
STORAGE: Material is to be stored under controlled dry environment (below 75° F). Use within 12 months from date of manufacture.
PACKAGING:10.3fl.oz.pertube|24tubespercarton
PROPERTIESTotal Solids (ASTM C 681) .........85%VolumeShrinkage(ASTMD2453)...<20%Wt/U.S.Gallon(ASTMD1475)...10.5+/-0.40lbsStaining (ASTM D 2202) .............NoneBlistering or Bleeding ................NoneUV Resistance .............................ExcellentSag ..............................0.15“ Max Full ButtonServiceTemperature.......-40degFto250degFApplicationTempRange...........40degFto95degFExtrudability(ASTMD2452).....40secondsmaxFlexibility (ASTM C 711) .............No loss of adhesion at -60degFFungus/Mildew ..................Resistant to growthHeat Aging ...No loss of surface tack or adhesionWeatherability(ASTMG154)...Nocracking,bleeding,orlossofrubbery characteristics
Chemical Resistance .................Excellent to water, ozone, water vapor, alcohols. Fair to weak for acids and bases. Poor to organic solvents.Static Water Pressure Head Test ...Passes 6” of static water pressure head, no water leakageAirLeakage(ASTME1680)[email protected]/sqftand0.0680cfm/ft&[email protected]/sqftand0.1365 cfm/ftWaterPenetration(ASTME1646)...Passed,noleakageWetFlammability(ASTMD56)...110degFflashpointVehicle Bleedout (ASTM C 772) ...No visible exudation of vehicle from sealant after three weeks at 158deg F on painted or unpainted metal surface.Aged Tack (ASTM D 2377) .........Permanently TackyHardness(ShoreOODurometer)...30-40
PS110615JS
DISCLAIMER: ALL TEST RESULTS AND SPECIFICATIONS ARE A RESULT OF LABORATORY TESTS. APPROPRIATE SAFETY FACTORS SHOULD BE USED BY THE USER OR SPECIFIER. DETERMINING THE PROPER FASTENER IS THE RESPONSIBILITY OF THE USER OR SPECIFIER. SINCE APPLICATION CONDITIONS VARY AND ARE UNCONTROLLABLE BY TFC, WE ASSUME NO LIABILITY FOR THE USE OF THIS INFORMATION.
50-year guarantee!
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD221.0616
BUTYL TAPE-SEAL™ was designed specifically for the metal building industry to provide optimal sealing in the harshest environments.
It adheres to most clean, dry metal surfaces and does not harden, bleed or stain. With pressure, it fills minor irregularities in the surface and seals the joints providing an effective barrier against water, moisture, dust, and dirt.
BUTYL TAPE-SEAL™ is an excellent choice for use around windows, doors, roof vents, stacks, access doors, and other penetration points.
Adheres to:• Painted Metal• Galvalume®• Kynar®• Aluminized Metal
Easy to install!
Specially formulated for use on metal roof and wall panels.
BUTYLTAPE-SEAL
Mineral spirits will readily facilitate the cleaning of tools and equipment.
PACKAGING
BUTYL TAPE-SEAL™ is extruded butyl material with a silicone backed release paper that is rolled and cut to specific lengths.
Our master cartons are constructed of 200 pound test material and the rolls are separated by silicone divider pads and protected by upright stacking cores.
CLEAN UP
SIZES
Size(T x W x L) TFC P.N.
Rolls/Ctns
Ctns/Pallet
3/32” x 3/8” x 45’ 0937BCT 48 303/32” x 1/2” x 50’ 0950BCT 22 503/32” x 1” x 45’ 0910BCT 24 301/8” x 1/2” x 50’ 1250BCT50 13 481/8” x 1” x 50’ 1210BCT50 8 48
3/16” x 1/4” x 40’ 1825BCT 20 483/16” x 7/8” x 40’ *DB 1887BCT 10 483/16” x 7/8” x 25’ *TB 1887BCT25TRI 8 64
3/16” x 2-1/2” x 20 *TB TC826W 6 60
Stocked sizes - Others available upon request
*DB denotes double bead*TB denotes triple bead
BUTYL TAPE-SEAL
52
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD223.0616
562.12 | Standard GradeCompounded to meet pre-engineered metal building specifications. It is soft, resilient and easily worked by hand; yet it adheres instantly to almost any normal surface without being cleaned. Material should be tested prior to application. It has excellent weathering characteristics while retaining adhesion and elasticity in both hot and cold environments. 562.12 is chemically inert and is non-corrosive to paint, metal, aluminum, copper, plastic and will not swell rubber.
562C.12 | High Performance Spacer CubesProprietary spacer cubes are added to prevent bottoming out of sealant when fasteners are installed. They also assist the sealant from extruding out of the joint due to thermal expansion or contraction of roof panels. As with 562.12, it has outstanding webbing and elongation properties along with excellent adhesion to glass, plastic, polyethylene, galvanized aluminum, Galvalume, siliconized polyester, polyurethane and polyvinyl fluoride painted substrates. Use on roof laps, end laps and side laps of metal buildings.
Using low cost inferior butyl tape can extrude out from the laps causing leaks!
PROBLEM
SOLUTIONDEVAN 562.12 butyl tape is formulated to withstand harsh environments. Using the non-compressible plastic spacer cubes (562.C.12), helps keep the sealant between the lap during thermal movement of the panels.
TFC is pleased to offer the highest performing butyl tape in the metal roofing industry! DEVAN butyl tapes are formulated for consistent performance and helps eliminate leaks caused by thermal movement of the panels.
We take great care in packaging to assure product arrives to the job undamaged.
PACKAGING
Devan Sealants are easy to install and provides long life performance.
INSTALLATION
TECHNICAL DATA
Movement caused by expansion and contraction.
Proprietary spacer cubes keep the butyl from extruding out beyond the lap.
Panel
DEVAN Butyl with spacer cubes
Sizes with Cubes Rolls Per Carton3/32” x 3/8” x 45 ft. 181/8” x 1” x 50 ft. 83/16” x 7/8” x 40 ft. double bead 83/16” x 2-1/2” x 20 ft. triple bead 9
SIZES
DEVAN BUTYL TAPE
ASTM E2140: Meets the requirements of Water Penetration of Metal Roof Panel Systems by Static Water Pressure Head.
Federal Specification: TT-C-1796A, Type II, Class B (supercedes MIL-C-1896B).
LEED: Conforms to Leadership in Energy and Environmental Design 2009 for New Construction, Indoor Environmental Quality: Section 4.1, Low-Emitting Materials: Adhesive & Sealants (SCAQMD) Rule # 1168, VOC limits.
NAAMM: Meets standard SS-1C-68.
FDA Regulation: Meets FDA Regulation, food additives, sub-part F, sub-paragraph 175.105 being composed of ingredients acceptable for packing and transporting food.
BUTYLTAPE-SEAL
53
CR
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD235.0616
Elk River Roofer's KitsRoofer's Kits are available in several combinations with each kit containing specific items. The combinations listed below are our most popular kits.
FALL PROTECTION
Contact TFC to choose from a wide selection of safety equipment to meet your needs!
Part # Product Description Weight
00800 HUV (01700) 5 Snappy Anchors (00710) & VLA-25’ (01310) 13.20
00803 HUV (01700) 1 SP-Anchor (00460) & VLA-25’ (01310) 13.50
00805 HUV (01700) 1 Temper Reusable (00455) & VLA-25’ (01310) 12.60
00810 HUV (01700) 5 Snappy Anchors (00710) & VLA-50’ (01320) 15.30
00813 HUV (01700) 1 SP-Anchor (00460) & VLA-50’ (01320) 15.15
00815 HUV (01700) 1 Temper Reusable (00455) & VLA-50’ (01320) 17.30
00830 HUV (01700) 2 Stainless Steel Reusable (00470) & VLA-25’ (01310) 10.70
00840 HUV (01700) 2 Stainless Steel Reusable (00470) & VLA-50’ (01320) 12.95
Guardian Fall ProtectionBucket of Safety | Roofer Kit
• Roofer’s Kits: CP+™ 48103• 1 D-ring Harness (S-XL)• 50′x 5/8″ CP+™ Lifeline• 13102 snaphook/thimble• 5/8” x 3’ trailing rope grab with attached nylon web
lanyard and Zsnaphook 3.6M Gate• Reusable Roof Anchor with fasteners• Bucket
• CP+™ 48103 one D-ring Harness• 30’ x 5/8” CP+™ Lifeline with attached rope grab and
attached ZORBER® web lanyard with Zsnaphook 3.6M Gate
• Reusable Roof Anchor with fasteners• Bucket• One Size Fits Most
Available in an easy to carry back-pack bag!
54
CR
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD232.0616
CONTRACTOR SUPPLIES
We have a full line of safety products to meet your needs!Hard Hats Safety Glasses and Shields
Ear Protection
First Aid Kits
Respirators
Call TFC for all of your miscellaneous contractor supplies!
Tarps | Contractor Garbage Bags | Job Site Rags
Job-Site Storage
Gloves
Job-site Coolers
55
CR
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD197.0616
Compact
Phillips Bit Tip #1 Phillips Bit Tip #2 Phillips Bit Tip #3
Slotted Bit Tip #8 Slotted Bit Tip #10 Slotted Bit Tip #12
Square Recess Bit Tip #1 Square Recess Bit Tip #2 Square Recess Bit Tip #3
Pozi-driv® Bit Tip #1 Pozi-driv® Bit Tip #2 Pozi-driv® Bit Tip #3
Torx® Bit Tip T10 Torx® Bit Tip T15 Torx® Bit Tip T20 Torx® Bit Tip T25 Torx® Bit Tip T27 Torx® Bit Tip T30 Torx® Bit Tip T40
1" Bit Tips
Phillips #2 / Slotted #8 Phillips #2 / Phillips #2 Phillips #2 / Square Recess #2
Double Ended Bits
2" Phillips Power Bit #1 2" Phillips Power Bit #2 2" Phillips Power Bit #3 Deck Power Bit #2
2" Square Recess Power Bit #1 2" Square Recess Power Bit #2 2" Square Recess Power Bit #3
3-1/2" Phillips Power Bit #1 3-1/2" Phillips Power Bit #2 3-1/2" Phillips Power Bit #3
3-1/2" Slotted Power Bit #6 3-1/2" Slotted Power Bit #8 3-1/2" Slotted Power Bit #10 3-1/2" Slotted Power Bit #12
3-1/2" Square Recess Power Bit #1 3-1/2" Square Recess Power Bit #2 3-1/2" Square Recess Power Bit #3
6" Phillips Power Bit #1 6" Phillips Power Bit #2 6" Phillips Power Bit #3
6" Slotted Power Bit #6 6" Slotted Power Bit #8 6" Slotted Power Bit #10 2" Square Recess Power Bit #6 2" Square Recess Power Bit #8 2" Square Recess Power Bit #10
Power Bits
Magnetic Drive Guides
Magnetic Socket DriversDescription Size LengthMagnetic hex socket 1/4" 1-7/16" Magnetic hex socket 5/16" 1-7/16" Magnetic hex socket 3/8" 1-1/2" Magnetic hex socket 1/4" 2-9/16" Magnetic hex socket 5/16" 2-9/16" Magnetic hex socket 3/8" 2-9/16"
Description LengthEyelag socket driver 2-9/16"
Depth sensing for drywall installation. Magnetic
Screw-driving Set
1" Phillips Bit Tips: (1) #1, (10) #2, (1) #3 1" Slotted Bit Tips: (1) #6, (2) #8, (1) #10 1" Square Recess Bit Tips: (1) #1, (6) #2, (1) #3 2" Phillips Power Bit: (1) #2 2" Square Recess Power Bit: (1) #2 Nutdrivers: (1) 1/4", (1) 5/16" Compact magnetic drive guide (1)
Magnetic Drive Guides (2) 1" Phillips Bit Tips: (1) #1, (1) #2 1" Slotted Bit Tips: (1) #8-10 1" Square Recess Bit Tip: (1) #2
29 Piece Set
TOOL ACCESSORIES
Bit Holders
Quick Change Magnetic
Magnetic Holder
Description Size LengthMagnetic Bit Holder 1/4" Drive 1-5/8" 2-1/4" 2-3/4" 3"
Length 2 3/8"
Special adjustable sleeve stabilizes the fastener during installation
Standard
Clear
56
800.486.1832 | www.trianglefastener.com
CR
TRIANGLE FASTENERCORPORATION
TFC PRODUCTQUICK FACTS
800.486.1832
Visit our websitefor the most up-to-date product
and technical information!
ww.trianglefastener.com
MD291.0616
SAW BLADES | RECIPROCATING
SAW BLADES | CIRCULAR
CUTOFF WHEELS | ABRASIVES
CORING BITS | HOLE SAWS
Reciprocating Saw BladesBlades for cutting, metal, wood, plastic and masonry.
Circular Saw BladesFor hand saws and chop saws. Cut metal, wood, concrete, plastic.
Diameters: 4-1/2" up to 14"
AbrasivesGrinding wheels and cutoff wheels.
Diameters: 10", 12", 14"
Hole SawsCut holes in metal , wood, plastic or concrete.
Diameters: 3/4" up to 4"
CUT | SAW | GRINDWE OFFER A FULL LINE
BLADES, SAWS, ABRASIVES AND CUTOFF WHEELS
57
CR
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
INDEX
Clip Screws | Ultra Low Profile ..................................... 5Coated Drill Screws ...................................................... 9Coated Drill Screws | Stainless Cap Head ................... 14Coated Drill Screws | WW ............................................ 10Coated Drill Screws | Zinc Head ................................... 14Company Information ................................................... 60CONCEALOR Pancake Head | #10, #12 ..................... 4CONCEALOR Pancake Head | #14 DP1 ..................... 6CONCEALOR Pancake Head |1/4” DP3 ...................... 7CONCEALOR Pancake Head |Pullout ......................... 8CONCEALOR Pancake Head |Technical Data ............. 8CONCEALOR ULP ....................................................... 5Concrete Anchor | SPIKE® | Technical Data ................ 44Concrete Quick Facts ................................................... 43Contractor Supplies | Misc. Products | Sell Sheet ........ 55DDandi-Eye Eyebolts ...................................................... 41Devan Butyl-Tape ......................................................... 53Drill Screws | Pull Over Values ..................................... 19Drill Screws | Security Screws ...................................... 17Drill Screws | Stainless Steel ........................................ 12Drill Screws | Technical Data ........................................ 19Drill Screws with Wings ................................................ 12Drill Screws with Wings ................................................ 13EEnd Cap | Flashing ....................................................... 48Eyebolts | Forged ......................................................... 41FFABLOK........................................................................ 36Fall Protection | Roofer Kit ............................................ 54Fastener Selection Chart | Substrate Compatibility ...... 30Flange Head Drill Screws ............................................. 10Flange Head Drill Screws | Stainless Cap Head .......... 14Flange Head Drill Screws | Zinc Head .......................... 14Flashing | End Cap ....................................................... 48Framing Screws | Exterior ............................................ 27GGauge Thicknesses ...................................................... 19GROMMET-SEAL RIVET ............................................. 37HHeavy Gauge Drill Screw |CS ...................................... 9Heavy Gauge Drill Screw |CS | WW ............................. 10Hex Washer Head Drill Screw | CS .............................. 9Hex Washer Head Drill Screw | CS | Stainless Cap Head ............................................... 14Hex Washer Head Drill Screw | CS | WW .................... 10Hex Washer Head Drill Screw | CS | Zinc Head ........... 14Hillside Washer | BRACER | Sizes ............................... 39Hillside Washer | BRACER LITE | Sizes ...................... 38IInstallation Tips | BLAZER Drill Screws ........................ 31Insulation Standoff Screws ........................................... 14
Page #8 Blazer Drill Screw | CS ............................................ 9#10 Blazer Drill Screw | CS .......................................... 9#10 Blazer Drill Screw | CS | WW ................................ 10#12 Blazer Drill Screw | CS .......................................... 9#12 Blazer Drill Screw | CS | Stainless Cap Head ....... 14#12 Blazer Drill Screw | CS | WW ................................ 10#12 Blazer Drill Screw | CS | Zinc Head ....................... 141/4” Blazer Drill Screw | CS .......................................... 91/4” Blazer Drill Screw | CS | Stainless Cap Head ....... 141/4” Blazer Drill Screw | CS | WW ................................ 101/4” Blazer Drill Screw | CS | Zinc Head ....................... 141/4” DP5 Heavy Gauge Drill Screws |CS ..................... 111/4” DP5 Heavy Gauge Drill Screws |CS | WW ............ 10#17 Type AB Stainless Cap Head ................................ 14#17 Type AB Zinc Head ................................................ 145/16” Blazer Drill Screw | CS ........................................ 9410 Stainless Steel Drill Screws ................................... 12AAbrasives | Blades Quick Facts .................................... 57Accessories | Bits and Sockets .................................... 56APS 500 Advanced Polymer Sealant | Colors .............. 51BBackout Resistant Screw | Product Information ........... 15Backout Resistant Screw | Sizes & Technical .............. 16Base Angle Attachment Kit ........................................... 42Bi-Metal Screws | Medium & Heavy Gauge ................. 26Bit Holders ................................................................... 56BLAZER Bond Seal Screws ........................................ 10Blazer Drill Screws |Technical Data .............................. 19Blazer Drills Screws - No Bonded Washer | CS ........... 9Blazer Drills Screws | Zinc Head .................................. 14Blazer Drills Screws -With Bonded Washer | CS.......... 10Blazer Drills Screws -With Stainless Cap Head ........... 14BLAZER Fastening Tips | Sell Sheet ........................... 31BLAZER Flange Head Screws .................................... 10BLAZER Flange Head Screws | Stainless Cap Head .. 14BLAZER Flange Head Screws | Zinc Head .................. 14Bonded Sealing Washers ............................................. 32Bonded Washer Drill Screws ........................................ 10BRACER Hillside Washer | Sizes ................................. 39BRACER LITE Hillside Washer | Sizes ........................ 38BULB-TITE RIVET ........................................................ 37BURR-BUSTER Self-Piercing Screws ......................... 27BUTYL TAPE ............................................................... 52BUTYL TAPE | With Cubes .......................................... 53CCarbon Steel Drill Screw .............................................. 9Carbon Steel Drill Screw | Stainless Cap Head ............ 14Carbon Steel Drill Screw | WW ..................................... 10Carbon Steel Drill Screw | Zinc Head ........................... 14Clip Screws | #10, #12 .................................................. 4Clip Screws | #14 DP1 .................................................. 6Clip Screws | 1/4” DP3 ................................................. 7Clip Screws | Pullout ..................................................... 8Clip Screws | Technical Data ........................................ 8
Contents Page Contents
58
CR
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
KKALIDA KOTE PAINT ................................................... 28LLong Life Coated Drill Screws ...................................... 9Long Life Coated Drill Screws | Stainless Cap Head ... 14Long Life Coated Drill Screws | WW ............................ 10Long Life Coated Drill Screws | Zinc Head ................... 14Long Life Coating ......................................................... 29Long Life Screws Zinc Cap and Stainless Cap ............ 14MMagnetic Drive Sockets ................................................ 56Markets Served ............................................................ 60Metal-to-Wood Screws | CS ......................................... 23Metal-to-Wood Screws | Stainless ................................ 24Metal-to-Wood Screws | Technical Data ....................... 25NNeed-It-Now Line Card | Fasteners .............................. 2Need-It-Now Line Card | Tools & Accessories .............. 3PPainted Fasteners ........................................................ 28Pancake Head Screw | Ultra Low Profile ...................... 5Pancake Head Screws | #10, #12 ................................ 4Pancake Head Screws | #14 DP1 ................................ 6Pancake Head Screws | 1/4” DP3 ................................ 7Pancake Head Screws | Technical Data ....................... 8Pancake Head Screws |Pullout .................................... 8PANEL-TITE | Metal-to-Wood Screws | CS .................. 23PANEL-TITE | Metal-to-Wood Screws | Stainless ........ 24PANEL-TITE | Technical Data....................................... 25Phillips Bits .................................................................. 56Pipe Flashing | PIPEMASTER® ................................... 46Pipe Flashing | PIPEMASTER® | 35 Year Flashing ..... 47PIPEMASTER® | Pipe Flashing | 35 Year Flashing ..... 47PIPEMASTER® | Pipe Flashing | Colors | Retrofit ....... 46Post Frame Screws | CS .............................................. 23Post Frame Screws | Technical Data ............................ 25Post Frame Screws |Stainless ...................................... 24Power Bits .................................................................... 56Pullout Data | Self-Drilling Screws Blazer ..................... 20QQuick Facts SEALANTS | Tapes & Flashings .............. 49Quick Facts SAWS | Abrasives..................................... 57RRake Angle Screw ........................................................ 18Rivets | Blind / Colors A-DEM ....................................... 33Rivets | Blind / Colors DEN-REF .................................. 34Rivets | Blind / Colors REG-ZIN ................................... 35Rivets | Blind | Technical Data ...................................... 35Roofer Safety Kit .......................................................... 54
SSafety | Roofer Kit ........................................................ 54Sealant | APS 500 Advanced Polymer Sealant | Color . 51Sealant | BUTYL TAPE ................................................. 52Sealant | BUTYL TAPE | With Cubes ........................... 53Sealant | Ultra 1000 Silicone | Color ............................. 50Sealants Quick Facts | Tapes & Flashings .................. 49Security Screws ............................................................ 17Self-Drilling Screws - No bonded washer | CS ............. 9Self-Drilling Screws | 410 Stainless Steel ..................... 12Self-Drilling Screws | Pull Out and Shear Data ............ 20Self-Drilling Screws | Pull Over Values ......................... 19Self-Drilling Screws | Technical Data ............................ 19Self-Drilling Screws | Zinc Head ................................... 14Self-Drilling Screws -With bonded washer | CS .......... 10Self-Drilling Screws With Bonded Washers .................. 10Self-Drilling Screws -With Stainless Cap Head ............ 14Self-Piercing Screws .................................................... 27Self-Tapping Screws with Washers .............................. 21Self-Tapping Screws with Washers | Technical Data .... 22Shear Data | Self-Drilling Screws Blazer ...................... 20Sheeting Screws with Washers .................................... 21Sheeting Screws with Washers | Technical Data .......... 22Shoulder Drill Screw ..................................................... 9Shoulder Screw ............................................................ 18Silicone Sealant | Ultra 1000 | Colors ........................... 50SPIKE® Drive Anchor | Technical Data ........................ 44Stainless Steel Sheeting Screws .................................. 21Stainless Steel Sheeting Screws | Technical Data ....... 22STRESS-LOK™ | Clamping Washer ............................ 40TTapping Screws with Washers ...................................... 21Tapping Screws with Washers | Technical Data ........... 22Technical Data | Self Drilling Screws/BLAZER ............. 19Technical Data | VRT Backout Resistant Screw ........... 16Technical Data | Wood-to-Metal Drill Screws ............... 13TRI-SEAL Coating ........................................................ 29UULP Low Profile Screw ................................................. 5Ultra 1000 Silicone Sealant | Colors ............................. 50Ultra Low Profile Screw ................................................ 5V ...................................................................................VRT | Product Information ............................................ 15VRT | Sizes ................................................................... 16WWashers | Bonded Sealing .......................................... 32Wedge Anchor | TRUBOLT | Technical Data ................ 45Winged Drill Screws ..................................................... 12Wood Screws with Washer | CS ................................... 23Wood Screws with Washer | Stainless ......................... 24Wood Screws with Washer | Technical Data ................ 25Wood-to-Metal Drill Screws .......................................... 13Wood-to-Metal Drill Screws | Full Line ......................... 12Wood-to-Metal Drill Screws | Technical Data................ 13
Page Contents Page Contents
59
Visit our website for the most up-to-date product and technical information!800.486.1832 | www.trianglefastener.comTRIANGLE FASTENER CORPORATION
MD2.0616
Alabama - Birmingham 3800 1st Ave. North Birmingham, AL 35222 P: 205.595.3444 | F: 205.595.7544
Alabama -Mobile 764 Lakeside Drive Suite A Mobile, AL 36693 P:251.665.5000 | F: 251.665.5001
Alabama - Montgomery 508 Hackel Drive Montgomery, AL 36117 P: 334.270.8800 | F: 334.270.0331
Arizona - Phoenix SalesGunnar MartinsonSales | Southwest TerritoryC: 480.291.2334 | F: 713.466.8390
Delaware - New Castle 243 Quigley Blvd. New Castle, DE 19720 P: 302.322.0600 | F: 302.322.5102
Florida - Ft Lauderdale 5600 NW 12th Ave Suite 303 Ft. Lauderdale, FL 33309 P: 954.771.5232 | F: 954.771.5441
Florida - Jacksonville 6800 Suemac Place, Suite 2Jacksonville, FL 32254P: 904.695.0404 | F: 904.695.0062
Florida - Orlando 114 Atlantic Annex Pt. Maitland, FL 32751P: 407.660.0167 | F: 407.660.1256
Florida - Tampa10111 Woodberry Road Tampa, FL 33619 P: 813.689.6877 | F: 813.689.6717
Georgia - Atlanta 2979 Pacific Drive Suite A Norcross, GA 30071 P: 770.417.1515 | F: 770.409.1451
Indiana - Indianapolis 7768 Zionsville Rd #400 Indianapolis, IN 46268 P: 317.872.3944 | F: 317.879.2181
Kentucky - Louisville SalesBret BorlandSales | KentuckyC: 502.919.0863 | F: 513.242.8209
Maryland - Baltimore 6550 Moravia Park Dr. Baltimore, MD 21237 P: 410.485.8665 | F: 410.485.4560
Michigan - Detroit SalesMark EnderleSales | Michigan / NW OhioC: 734.674.2466 | F: 216.351.5008
Mississippi - Jackson 102 Diane Dr. Richland, MS 39218 P: 601.664.3449 | F:601.664.7185
North Carolina - Charlotte 3317 Pelton Street Charlotte, NC 28217 P: 704.586.0400 | F: 704.586.0300
North Carolina - Raleigh 2030 Garner Station Blvd. Raleigh, NC 27603 P: 919.779.4510 | F: 919.779.6870
Ohio - Cincinnati 1021 W. 8th Street Cincinnati, OH 45203 P: 513.242.5802 | F: 513.242.8209
Ohio - Cleveland 4661 Hinckley Ind. Pkwy. Cleveland, OH 44109 P: 216.351.9933 | F: 216.351.5008
Ohio - Columbus 1244 West Goodale Blvd. Columbus, OH 43212P: 614.487.8800 | F: 614).487.1634
Pennsylvania - Pittsburgh (Corp.)1925 Preble Ave. Pittsburgh, PA 15233 P: 412.321.5000 | F: 412.321.7838
Tennessee - Madison 213 Nesbitt Lane Madison, TN 37115 P: 615.865.0007 | F: 615.868.7257
Texas - Dallas 2801 West Airport Freeway Irving, TX 75062 P: 972.659.9400 | F: 972.659.9403
Texas - Houston 5210 Brittmoore Houston, TX 77041 P: 713.466.7758 | F: 713.466.8390
Virginia - Richmond 2256-D Dabney Rd Richmond, VA 23230 P: 804.358.7040 | F: 804.358.7043
Washington - Seattle 18404 Cascade Ave South Suite 140 Seattle, WA 98188 P: 206.575.0144 | F: 206.575.111
We serve the fastening systems needs of the following core markets.
Flat Roofing Low Slope Roofing Industry
Metal Building / Roofing | Post Frame | Curtain Wall Metal Building, Metal Roofing and Siding
Drywall | Interior Steel Framing, Drywall, EIFS, HVAC, Electrical, Mechanical
FASTENING SYSTEMS AND SOLUTIONS FOR COMMERCIAL CONSTRUCTION
Since 1977, Triangle Fastener Corporation has supplied the construction industry with the most comprehensive lines of standard and specialty fastening systems solutions. We offer the latest fastening systems technologies that provide high performance and low in-place costs.
But that’s only part of the story…
Our local service centers stock a variety of products that meet your performance and quality demands. Coupled with our “hands-on" approach to servicing your needs, you will get the attention you deserve.
How Can We Help You? Contact us Toll Free at 800.486.1832
Stop by our showroom and be serviced by our knowledgeable staff of fastening systems specialists.
• Over 15,000 standard and specialty items in stock, we can ship most orders the same day!
• Local delivery capabilities will get your order to the job site when you need it!
● Product Training ● Job Site Assistance ● Fastening Recommendations ● Engineering Support ● Product Development ● Delivery Program ● Inventory Management Programs
CR
MARKETS SERVED
LOCATIONS
SERVICES
60