06 - Cylinder Head - Valves
-
Upload
erick-rivas -
Category
Documents
-
view
234 -
download
0
Transcript of 06 - Cylinder Head - Valves
-
8/11/2019 06 - Cylinder Head - Valves
1/2161
ITEM STA N D A R D SER VIC E LIM IT
C ylinder com pression 1.350 kPa (13.5 kg/cm 2; 192 psi).
C am lobe height IN . 31.579 - 31.739 (1.243-1.249) 31.30 (1.232)
EX 31.419 - 31.579 (1.236-1.243) 31.20 (1.228)
C ylinder head w arpage 0.10 (0.004)
R ocker arm I.D . 12.000 - 12.018 (0.4724 - 0.4731) 12.05 (0.474)
Shaft O .D . 11.977 - 11.995 (0.4715 - 0.4722) 11.93 (0.470)
Arm -to-shaft clearance 0,005 - 0,041 (0.0002 - 0.0016) 0.08 (0.003)
Valve spring free length IN N ER 39.2 (1.543) 38.0 (1.50)
O U TER 44.85 (1.766) 43.5 (1.71)
Valve stem O .D . IN 5.450 - 5.465 (0.2146 - 0.2152) 5.44 (0.214)
EX 5.430 - 5.445 (0.2138 - 0.2144) 5.42 (0.213)
Valve guide I.D . IN 5.475 - 5.485 (0.2156 - 0.2159) 5.50 (0.217)
EX 5.475 - 5.485 (0.2156 - 0.2159) 5.50 (0.217)
Stem -to-guide clearance IN 0.010 - 0.035 (0.0004 - 0.0014) 0.06 (0.002)
EX 0.030 - 0.055 (0.0012 - 0.0022) 0.08 (0.003)
Valve seat w idth 1.1 - 1.3 (0.043-0.051) 1.5 (0.06)
XL200 6.
SERVICE INFORMATION 6-1
TROUBLESHOOTING 6-2
CYLINDER HEAD COVER/CAMSHAFTREMOVAL 6-3
CYLINDER HEAD REMOVAL 6-6
CYLINDER HEAD DISASSEMBLY 6-7
VALVE GUIDE REPLACEMENT 6-9
VALVE SEAT INSPECTION/REFACING 6-10
CYLINDER HEAD ASSEMBLY 6-13
CYLINDER HEAD INSTALLATION 6-14
CAMSHAFT/CYLINDER HEAD COVERINSTALLATION 6-15
SERVICE INFORMATION
GENERAL
This section covers service proced ure for the cylind er head and valves.
The eng ine m ust be rem oved to service the cam shaft, cylind er head , valves and rocker arm s.
C am shaft and rocker arm lub rication oil is fed through an oil passage. B e sure the passage is not clog ged .
C lean all disassem bled parts w ith clean solvent and dry them by blow ing them off w ith com pressed air before inspection.
Pour clean engine oil into the oil pockets in the cylinder head during assem bly to lubricate the cam shaft lobes.
SPECIFICATIONS
UNIT: mm (in)
CYLINDER
HEAD/VALVES
-
8/11/2019 06 - Cylinder Head - Valves
2/21
XL200C YLIN D ER H EAD /VALVES
6-0
15 N.m (1.5 kg.m, 11ft-lb)
12 N.m (1.2 kg.m, 9ft-lb)
12 N.m (1.2 kg.m, 9ft-lb)
10 N.m (1.0 kg.m, 7ft-lb)
10 N.m (1.0 kg.m, 7ft-lb)
4 N.m (0.4 kg.m, 3ft-lb)
8 N.m (0.8 kg.m, 6ft-lb)
6 N.m (0.6 kg.m, 4ft-lb)
10 N.m (1.0 kg.m, 7ft-lb)
14 N.m (1.4 kg.m, 10ft-lb)
27 N.m (2.7 kg.m, 20ft-lb)
-
8/11/2019 06 - Cylinder Head - Valves
3/21
TORQUE VALUES
Valve adjusting hole cap 15 N .m (1,5 kg.m , 11 ft-lb)
V alve ad justing screw lock nut 14 N .m (1,4 kg .m , 10 ft-lb )
C ylind er head cover 8 m m cap nut 27 N .m (2,7 kg .m , 20 ft-lb )
C ylinder head cover 6 m m socket bolt 10 N .m (1,0 kg.m , 7 ft-lb)
C am sprocket bolt 12 N .m (1,2 kg.m , 9 ft-lb)
C am chain tensioner lifter m ounting bolt 12 N .m (1,2 kg.m , 9 ft-lb)C am chain tensioner lifter sealing screw 4 N .m (0,4 kg.m , 3 ft-lb)
Tim ing hole cap 6 N .m (0,6 kg.m . 4 ft-lb)
C rankshaft hole cap 8 N .m (0,8 kg.m , 6 ft-lb)
TOOLS
Valve guide ream er, 5.485 m m 07984-0980001
Valve guide driver, 5,5 m m 07742-0010100B R
Valve spring com pressor 07757-0010000B R
TROUBLESHOOTING
Engine top -end prob lem s usually affect engine perform ance. These can be diag nosed by a com pression or leak dow n test,or by tracing noises to the top -end w ith a sounding rod or stethoscop e.
If the perform ance is poor at low speeds, check for white sm oke in the crankcase breather tub e. If the tub e is sm oky, check
for a seized piston ring.
Compression too low, hard starting or poor per- Excessive smokeformance at low speed W orn valve stem or valve g uideValves D am aged stem seal
Incorrect valve adjustm ent Faulty cylinder or piston (Section 7)
Burned or bent valves
Incorrect valve tim ing Excessive noiseBroken valve spring Incorrect valve clearance
W eak valve spring Sticking valve or broken valve spring
C ylinder head W orn or dam aged push rod
Leaking or dam aged cylinder head gasket Loose or worn cam chainW arped or cracked cylinder head W orn or dam aged cam chain tensioner
Faulty cylind er/p iston (S ection 7) W orn cam sp rocket teeth
W orn rocker arm and/or shaft
Compression too high, overheating or knocking Faulty cylinder or piston (Section 7)
Excessive carbon b uild-up in cylinder or on top of
piston Rough idle
Low cylind er com pression
Intake air leak
XL200
6-2
C YLIN D ER H EAD /VALVES
-
8/11/2019 06 - Cylinder Head - Valves
4/21
XL200 C YLIN D ER H EAD /VALVES
6-3
CYLINDER HEAD COVER/CAMSHAFT
REMOVALR em ove the follow ing :
starter m otor
crankshaft/tim ing hole caps
R em ove the bolts, cam chain tensioner lifter and gasket.
A lign the Tm ark on the flyw heel w ith the index m ark on the left
crankcase cover by turning the crankshaft counterclockw ise.
R em ove the valve adjusting hole caps and m ake sure the piston
is at T.D .C . on the com pression stroke b y checking for clearance
at both rocker arm s.
If the piston is not at T.D .C . on the com pression stroke, rotate thecrankshaft 360 deg rees counterclockw ise and recheck.
R em ove the cam sprocket cover.
R em ove the cam sprocket bolts by holding the crankshaft.
R em ove the cam sprocket from the cam shaft flange, then rem ove
the cam chain from the sprocket.
N O T E
Susp end the cam chain w ith a piece of w ire to prevent it
from falling into the crankcase.
CAM CHAIN TENSIONER
BOLTS
T MARK
INDEX MARK
CAM SPROCKET COVER
CAM SPROCKET CAM CHAIN
BOLTS
-
8/11/2019 06 - Cylinder Head - Valves
5/21
XL200
6-4
R em ove the eng ine hanger plate.
R em ove the cylind er head cover cap nuts/sealing w ashers and
flange bolts in a g radual, crisscross p attern.
R em ove the cylind er head cover.
R em ove the cam shaft.
R em ove the d ow el pins.
N O T E
It is not necessary to force them out.
R em ove the rub ber plug ; do not lose it.
C lean off any sealant m aterial from the head cover and cylind er
head m ating surface.
CAMSHAFT INSPECTION
Turn the outer races of cam shaft bearing s w ith your fing er.
The bearing s should turn sm oothly and quietly.
A lso check that the inner races fit tightly on the cam shaft.
M easure the height of each cam lob e and insp ect it for w ear or
dam age.
SERVICE LIMIT:Intake: 31.30 mm (1.232 in)Exhaust: 31.20 mm (1.228 in)
C YLIN D ER H EAD /VALVES
HEAD COVER BOLTS
CAP NUT/SEALING WASHER
CAMSHAFT DOWEL PIN
RUBBER PLUG
-
8/11/2019 06 - Cylinder Head - Valves
6/21
TENSIONER LIFTER
SCREW
PLATE
6 mm BOLT
ROCKER ARM SHAFT ROCKER ARM
ROCKER ARM ROCKER ARM SHAFT
XL200 C YLIN D ER H EAD /VALVES
6-5
TENSIONER LIFTER INSPECTION
R em ove the cam chain tensioner lifter sealing bolt and O -ring .
C heck the lifter operation:
the tensioner shaft should not go into the body unless it is
pushed.
CYLINDER HEAD COVER DISASSEMBLY
R em ove the rocker arm shaft plate by rem oving the setting
screw .
R em ove the rocker arm shafts by screw ing a 6 m m bolt into the
threaded ends as show n.
R em ove the rocker arm s.
ROCKER ARM/SHAFT INSPECTION
Inspect the rocker arm slipper surfaces for excessive w ear.
Insp ect the rocker arm s and shafts for w ear or dam ag e.
N O T E
M easure the I.D . of each rocker arm .
SERVICE LIMIT: 12.05 mm (0.474 in)
M easure the O .D . of each rocker arm shaft.
SERVICE LIMIT: 11.93 mm (0.470 in)
C alculate the rocker arm -to-shaft clearance.
SERVICE LIMIT: 0.08 mm (0.003 in)
If the rocker arm s require servicing or replacem ent, inspect
the cam lobes for scoring, chipping or flat spots.
W hen it turned clockw ise w ith a screw driver, the tensioner
shaft shoud be pulled into the bod y. The shaft should spring
out of the bod y as soon as the screw driver is released.
M ake a tensioner shaft stopper tool out of a thin p iece of steel
(0.8 m m thick) using the diag ram .
(0.8 mm thick)
-
8/11/2019 06 - Cylinder Head - Valves
7/21
XL200
6-6
CYLINDER HEAD REMOVAL
R em ove the follow ing :
cylind er head cover
engine from the fram e
cylind er head socket bolt/w asher
cylinder head
cam chain guide
gasket
dow el pins
C lean off any gasket m aterial from the cylind er head and
cylind er m ating surfaces.
R em ove the cam chain tensioner.
C heck the cam chain tensioner for excessive w ear or dam ag e.
C heck the cam chain g uide for excessive w ear or dam age.
C YLIN D ER H EAD /VALVES
CYLINDER HEAD SOCKET BOLT/WASHER
CAM CHAIN GUIDE
GASKET DOWEL PIN
CAM CHAIN TENSIONER
CAM CHAIN GUIDE
-
8/11/2019 06 - Cylinder Head - Valves
8/21
XL200 C YLIN D ER H EAD /VALVES
6-7
CYLINDER HEAD DISASSEMBLY
R em ove the cam chain tensioner pivot bolt, w asher and cam
chain tensioner.
R em ove the socket bolts and carburetor insulator.
W hile com pressing the valve spring w ith a valve spring
com pressor, rem ove the valve cotters.
h
TOOL:Valve spring compressor
To prevent loss of tension, do not compress the valve springmore than necessary to remove the cotters.
Loosen the valve spring com pressor and rem ove the follow ing :
sp ring retainers
outer and inner valve springs
spring seatsinlet and exhaust valve
N O T E
R em ove the carbon d eposits from the com bustion cham ber.
C lean off any gasket m aterials from the cylind er head surface.
M ark all disassem bled parts to ensure correct reassem bly.
INSPECTION
C YLIN D ER HEA DC heck the spark plug hole and valve area for cracks.
C heck the cylind er head for w arpag e w ith a straight ed ge and a
feeler gaug e.
SERVICE LIMIT: 0.10 mm (0.004 in)
CAM CHAIN TENSIONER INSULATOR
PIVOT BOLT/WASHER SOCKET BOLT
SPRING COMPRESSOR
STEM SEAL OUTER SPRING SPRING RETAINER
VALVE SPRING SEAT INNER SPRING
-
8/11/2019 06 - Cylinder Head - Valves
9/21
XL200
6-8
VALVE
Inspect the valve for trueness, burning , scratches or ab norm al
stem w ear.
M easure the valve stem O .D .
SERVICE LIMIT:
In: 5.44 mm (0.214 in)Ex: 5.42 mm (0.213 in)
Insert each valve into the valve guide and check the valve
m ovem ent in the guide.
VALVE G U ID E
N O T E
R eam the valve g uide to rem ove the carbon build-up before
checking the valve g uide.A lw ays rotate the ream er clockw ise, never couterclockw ise
w hen installing , rem oving and ream ing .
M easure and record each valve guide I.D . w ith a b all gauge or
inside m icrom eter.
SERVICE LIMIT: IN/EX: 5.50 mm (0.217 in)
C alculate the stem -to-guide clearance.
SERVICE LIMIT:
IN: 0.06 mm (0.002 in)EX: 0.08 mm (0.003 in)
N O T E
If the stem -to-guide clearance exceeds the service lim it,
determ ine if a new guide w ith standard dim ensions w ould
bring the clearance w ithin tolerance. If so, replace the
guides as necessary and ream to fit.
If the stem -to-guide clearance still exceeds the service lim it
w ith new guides, rep lace the valve g uide ream ers
R eface the valve seat w henever new valve guides areinstalled.
C YLIN D ER H EAD /VALVES
VALVE GUIDE REAMER
-
8/11/2019 06 - Cylinder Head - Valves
10/21
XL200 C YLIN D ER H EAD /VALVES
6-9
VA LVE SPR IN G
M easure the valve spring free length.
SERVICE LIMIT:Inner: 38.0 mm (1.50 in)Outer: 43.5 mm (1.71 in)
VALVE GUIDE REPLACEMENT
C hill valve guides in the freezer section of a refrigerator for about
an hour.
H eat the cylind er head to 100C w ith a hot plate or oven.
t
To avoid burns, w ear heavy gloves w hen handling the
heated cylinder head.
h
Sup port the cylind er head and drive out the valve g uide from the
valve port w ith a valve guide driver.
h
TOOL:Valve guide driver, 5.5 mm
Avoid damaging the cylinder head.
Do not use a torch to heat the cylinder head; it may cause
warping.
Place a new O -ring on the new valve guide.
Install a valve guide from the top of the cylinder head.
h
TOOL:Valve guide driver, 5,5 mm
When installing a valve guide, take care not to damage thecylinder head.
VALVE GUIDE DRIVER
VALVE GUIDE DRIVER
-
8/11/2019 06 - Cylinder Head - Valves
11/21
XL200
6-10
A fter driving in the valve guide, ream it w ith a valve guide
ream er.
N O T E
C lean the cylind er head thoroughly to rem ove any m etal particles.
R eface the valve seat.
U se cutting oil on the ream er during this operation.
A lw ays rotate the ream er clockw ise, never
counterclockw ise.
VALVE SEAT INSPECTION/REFACING
VALVE SEAT INSPECTION
C lean the intake and exhaust valves thoroughly to rem ove the
carbon d ep osits.
A pply light coating if Prussian B lue to the valve seats.
Lap the valves and seats using a rub ber hose or other hand
lapping tool.
R em ove the tool and insp ect the w idth of each valve seat.
STANDARD: 1.1 - 1.3mm (0.04 - 0.05 in)
SERVICE LIMIT: 1.5 mm (0.06 in)
If the valve seat is too w ide, too narrow or has low spots, the seat
m ust be g round .
h
The valve cannot be ground. If a valve face is burned orbadly worn or it contact the seat unevenly, replace the valve.
C YLIN D ER H EAD /VALVES
VALVE GUIDE REAMER
(1) SEAT WIDTH
-
8/11/2019 06 - Cylinder Head - Valves
12/21
XL200 C YLIN D ER H EAD /VALVES
6-11
VALVE SEAT GRINDING
H onda V alve Seat C utters, a g rind er or eq uivalent valve seat
refacing eq uipam ent are recom m ended to correct a w orn valve
seat.
N O T E
Follow the refacer m anufacturers operating instructions.
U se a 45 deg ree cutter to rem ove ant roughness or irreg ularities
from the seat.
N O T E
Reface the valve seat w ith a 45 deg ree cutter when a valve
guide is rep laced .
U sing 32 deg ree cutter, rem ove 1/4 of the exiting valve seat
m aterial.
VALVE GUIDE REAMER
-
8/11/2019 06 - Cylinder Head - Valves
13/21
XL200
6-12
U sing 60 d eg ree cutter, rem ove the bottom 1/4 of the oil seat.
R em ove the cutter and inspect the area you have just rem oved.
Install a 45 degree finish cutter and cut the seat to proper w idth.
M ake sure that all pitting and irregularities are rem oved.
R efinish if necessary.
STANDARD SEAT WIDTH: 1.1 - 1.3 mm (0.04-0.05 in)
A pply thin coat of Prussian B lue to the valve seat.
Press the valve throug h the valve guide and onto the seat to
m ake a clear pattern.
N O T E
If the contact area is too high on the valve, the seat m ust be
low ered using a 32 deg ree flat cutter.
The location of the valve seat in relation to the valve face is
very im portant for good sealing .
If the contact area is too low on the valve, the seat m ust be
raised using a 60 deg ree inner cutter.
C YLIN D ER H EAD /VALVES
-
8/11/2019 06 - Cylinder Head - Valves
14/21
XL200 C YLIN D ER H EAD /VALVES
6-13
R efinish the seat to sp ecifications, using a 45 d egree finish
cutter.
A fter cutting the seat, ap ply lap ping com pound to the valve face,
and lap the valve using light pressure.
A fter lap ping , w ash all residual com pound off the cylind er head
and valve.
CYLINDER HEAD ASSEMBLY
Install the inner and outer valve spring seats and new valve stem
seals.
Lubricate each valve stem w ith engine oil.
Insert the intake and exhaust valve into the valve guides.
Install the valve sp ring seats, sp rings and retainers.
N O T E
Install the valve sp rings w ith the narrow pitch end facing the
com bustion cham ber.
C om press the valve spring and install the valve cotters.
h
TOOL:Valve spring compressor
To prevent loss of tension, do not compress the valve spring
more than necessary.
STEM SEAL
STEM SEAL OUTER SPRING SPRING RETAINER
VALVE SPRING SEAT INNER SPRING
SPRING COMPRESSOR
-
8/11/2019 06 - Cylinder Head - Valves
15/21
XL200
6-14
Tap the stem s gently w ith a plastic ham m er to firm ly seat the
cotters.
h
Support the cylinder head above the work bench surface toprevent valve damage.
C heck the insulator O -ring is in good condition, replace if
necessary.
Tighten the insulator socket bolt securely.
Install the cam chain tensioner, w asher and pivot bolt.
Tighten the pivot bolt to the sp ecified torque.
TORQUE: 10 N.m (1.0 kg.m, 7 ft-lb)
CYLINDER HEAD INSTALLATION
Place the bottom end of the cam chain g uide into the groove in
the left crankcase, and its bosses in the grooves in the cylinder
up per surface.
N O T E
M ake sure that the cam chain is p rop erly installed on the
tim ing sprocket as show n.
C YLIN D ER H EAD /VALVES
INSULATOR
O-RING
CAM CHAIN TENSIONER
PIVOT BOLT/WASHER SOCKET BOLT
ALIGN
CAM CHAIN GUIDE
-
8/11/2019 06 - Cylinder Head - Valves
16/21
XL200 C YLIN D ER H EAD /VALVES
6-15
C lean the cylind er head gasket surface of any gasket m aterials.
N O T E
Install the dow el pins, new O -ring and new cylind er head gasket.
D o not allow dust and dirt to enter the engine.
Install the cylinder head
Install a new sealing w asher and the tensioner pivot bolt through
the tensioner hole.
Tighten the bolt to the specified torque.
TORQUE: 10 N.m (1.0 kg.m, 7 ft-lb)
CAMSHAFT/CYLINDER HEAD COVER
INSTALLATION
CYLINDER HEAD COVER ASSEMBLY
A pply oil to the rocker arm shafts.
Install the rocker arm s and rocker arm shafts in the cylinder head
cover.
W ith the rocker arm shaft reliefs on the inside, install the rocker
arm shaft plate.
Tighten the setting screw securely.
CAMSHAFT/CYLINDER HEAD COVER INSTALLATION
Install the dow el pins and rub ber plug .
DOWEL PIN GASKET
SOCKET BOLT/WASHER
CYLINDER HEAD
SCREW PLATE
ROCKER ARM ROCKER ARM SHAFT
R U B B E R P LU G
DO W EL PINS
-
8/11/2019 06 - Cylinder Head - Valves
17/21
XL200
6-16
A pply oil to the cam lob es and cam shaft bearing s.
Install the cam shaft in the cylinder head, positioning the cam
lobes dow n as show n.
Pour fresh oil into the oil pocket in the cylinder head until the
cam s are subm erged.
A pply sealant to the m ating surface of the cylind er head cover.
h
Install the head cover onto the cylinder head.
Do not apply sealant to the oil passage.
A pply oil to the cap nut thread s.
Install the new sealing w ashers/cap nuts and flange bolts.
Tighten the cap nut in a crisscross p attern in 2-3 steps.
TORQUE: 27 N.m (2.7 kg.m, 20 ft-lb)
Tighten the flange bolts and setting bolt in a gradual crisscross
pattern.
TORQUE: 10 N.m (1.0 kg.m, 7 ft-lb)
A lign the Tm ark on the flyw heel w ith the index m ark on the left
crankcase cover by turning the crankshaft counterclockw ise.
C YLIN D ER H EAD /VALVES
CAMSHAFT
SEALANT
HEAD COVER
(1) INDEX MARK
(2) T MARK
CA P NU T/W ASHER
B O L T
-
8/11/2019 06 - Cylinder Head - Valves
18/21
XL200 C YLIN D ER H EAD /VALVES
6-17
Install the cam sprocket w ith its tim ing m arks facing out.
Install the cam chain over the sprocket as show n.
N O T E
If it is difficult to install the chain over the sp rocket, m ake
sure the chain is set properly on the tim ing sprocket.
A lign the tim ing m arks on the cam sprocket w ith the m ating
surface of the cylinder head and cover, w ithout rotating the
crankshaft.
A pply oil to the cam sprocket bolts and install them .
Tighten the bolts to the specified torque.
TORQUE: 12 N.m (1.2 kg.m, 9 ft-lb)
Turn the tensioner shaft clockw ise w ith a sm all screw driver to
retract the tensioner, and hold it in the fully retracted position.
N O T E
W ed ge the tensioner shaft w ith a piece of w ire to hold the
tensioner.
The tensioner w ill forced out by the spring w hen it is
released.
Install a new gasket on the cam chain tensioner lifter and install
it.
CAM SPROCKET
CAM CHAIN
TIMING MARKS
BOLTS
TENSIONER LIFTER SCREWDRIVER
GASKET TENSIONER LIFTER
-
8/11/2019 06 - Cylinder Head - Valves
19/21
XL200
6-18
Tighten the cam chain tensioner lifter m ounting bolts.
TORQUE: 12 N.m (1.2 kg.m, 9 ft-lb)
R em ove the w ire holder piece from the tensioner lifter.
Install and tighten the screw w ith a new O -ring .
Tighten the screw to the specified torque.
TORQUE: 4 N.m (0.4 kg.m, 3 ft-lb)
R otate the crankshaft counterclockw ise a few tim es and recheck
the valve tim ing.
Install a new gasket and O -ring onto the sprocket cover.
Install the sprocket cover w ith its oil pocket facing dow n as
show n.
Install and tighten the cover bolts securely.
A pply clean engine oil to the O -ring s of the adjusting hole caps.
Install and tighten the cap bolts.
TORQUE: 15 N.m (1.5 kg.m, 11 ft-lb)
Install and tighten the tim ing hole cap and crankshaft hole cap.
TORQUE:Timing hole cap: 6 N.m (0.6 kg.m, 4 ft-lb)
Crankshaft hole cap: 8 N.m (0.8 kg.m, 6 ft-lb)
Install the follow ing:
starter m otor
engine
C YLIN D ER H EAD /VALVES
SOCKET BOLT SCREW
CAM SPROCKET COVER
O-RING
BOLTS
CRANKSHAFT HOLE CAP
TIMING HOLE CAP
-
8/11/2019 06 - Cylinder Head - Valves
20/21
XL200 C YLIN D ER H EAD /VALVES
6-19
NOTAS
-
8/11/2019 06 - Cylinder Head - Valves
21/21
G ENERA L IN FO RM ATIO N
HOW TO USE THIS MANUAL
This service m anual describes the service
proced ure for the XL200.
Throughout the m anual, the follow ing
abbreviations are used to identify individual
m odels.
Follow the M aintenance Sched ule (Section 3)
recom m endations to ensure that the vehicle is in
peak operation cond ition.
Perform ing the first scheduled m aintenance is very
im portant. It com pensates for the initial w ear that
occurs during the break-in p eriod .
Section 1 through 3 apply to the w hole m otorcycle,
w hile section 4 throug h 18 describe parts of the
m otorcycle, grouped according to location.
Find the section you w ant on this p ag e, then turn to
the tab le of contents on pag e 1 of that section.
M ost sections start w ith an assem bly or system
illustration, service inform ation and troubleshooting
for the section, the subsequent pag es g ive detailed
procedures.
If you dont know the source of the trouble, go to
section 20 TRO U BLES H O O TIN G .
A ll inform ation, illustrations, directions and
sp ecifications included in this publication are
based on the latest product inform ation available
at the tim e of approval for printing. M O TO
H O N D A D A A M AZ N IA LTD A. Reserves the
right to m ake chang es at any tim e w ithout notice
and w ithout incurring any oblication w hatever.
N ot part of this pub lication m ay be reprod uced
w ithout w ritten perm ission.
CONTENTS
G ENERA L IN FO RM ATIO N 1
LU BR IC A TIO N
2M AIN TENAN C E 3
FUEL SYSTEM 4
EN G IN E RE M O VA L/IN STALLATIO N 5
C YLIN D ER H EAD /VALVES 6
C YLIN D ER /PISTO N 7
C LUTC H /G EAR SH IFT LIN KA G E 8
ALTERN ATO R/STARTER CLUTC H 9
C RA N KSH AFT/KIC KSTAR TER/TRAN SM ISSIO N 10
FRO N T W H EEL/SU SPEN SIO N /STEERIN G 11
REA R W H EEL/SU SPENSIO N 12
H YDR AU LIC BRA KE 13
FAIR IN G /EXH A U ST SYS TEM 14
C H ARG IN G SYSTEM 15
IG N ITIO N SY STEM
16ELEC TRIC STA RTER 17
LIG H TS/M ETERS /SW ITC H ESELECTRIC
ST
ARTER
FRAME
ENGINE
18
W IRIN G D IAG RA M 19
TRO U BLESHO O TIN G 20
C ode A rea (type)
D K G eneral Type
2LA Latin A m erica
http://informat.pdf/http://informat.pdf/http://lubricat.pdf/http://lubricat.pdf/http://mainten.pdf/http://mainten.pdf/http://fuel.pdf/http://fuel.pdf/http://engine.pdf/http://engine.pdf/http://head.pdf/http://head.pdf/http://cylinder.pdf/http://cylinder.pdf/http://clutch.pdf/http://clutch.pdf/http://alternat.pdf/http://alternat.pdf/http://transmis.pdf/http://transmis.pdf/http://transmis.pdf/http://suspens.pdf/http://suspens.pdf/http://rearwhee.pdf/http://rearwhee.pdf/http://brake.pdf/http://brake.pdf/http://fairing.pdf/http://fairing.pdf/http://battery.pdf/http://battery.pdf/http://ignition.pdf/http://ignition.pdf/http://starter.pdf/http://starter.pdf/http://lights.pdf/http://lights.pdf/http://diagram.pdf/http://diagram.pdf/http://troubles.pdf/http://troubles.pdf/http://troubles.pdf/http://diagram.pdf/http://lights.pdf/http://starter.pdf/http://ignition.pdf/http://battery.pdf/http://fairing.pdf/http://brake.pdf/http://rearwhee.pdf/http://suspens.pdf/http://transmis.pdf/http://alternat.pdf/http://clutch.pdf/http://cylinder.pdf/http://head.pdf/http://engine.pdf/http://fuel.pdf/http://mainten.pdf/http://lubricat.pdf/http://informat.pdf/