04Mohr Stress Diagram
-
Upload
fkbs-malang -
Category
Documents
-
view
2 -
download
0
description
Transcript of 04Mohr Stress Diagram
![Page 1: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/1.jpg)
The Mohr Stress Diagram
Edvard Munch as a young geologist!
![Page 2: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/2.jpg)
Material in the chapter is covered
in Chapter 7 in Fossen’s text
![Page 3: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/3.jpg)
The Mohr Stress Diagram
A means by which two stresses acting on a plane of known
orientation can be plotted as the components of normal and
shear stresses (derived separately from each of the two stresses).
The Mohr circle is thus an elegant way to determine the shear and
normal stresses for a pair of stresses oriented obliquely to the plane
in question. The Mohr circle allows you to quickly read this for
planes of any orientation.
It also makes it easy to visualize mean stress and differences in
stress, or deviatoric stress and relate these to deformation.
![Page 4: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/4.jpg)
σn = (σ1 + σ3) + (σ1 - σ3) cos 2Θ!2!2!
σs = (σ1 - σ3) sin 2Θ!2!
Stress Equations
Normal Stress
Shear Stress
Two perpendicular stresses oriented at any angle to a plane!
Theta is the angle between the maximum stress and the pole
to the plane the stresses are acting upon.!
![Page 5: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/5.jpg)
The Mohr Stress Diagram σn = (σ1 + σ3) + (σ1 - σ3) cos 2Θ!
2!2!
σs = (σ1 - σ3) sin 2Θ!2!
Theta = angle between !The normal to the plane and the maximum principle stress (see Fig 4.1 in Fossen)!
![Page 6: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/6.jpg)
The Mohr Circle - (mean or average stress)
Mean Stress!
![Page 7: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/7.jpg)
The Mohr Circle – radius or deviatoric stress
Deviatoric Stress!
![Page 8: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/8.jpg)
The Mohr Circle – diameter or differential stress
Differential Stress!
![Page 9: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/9.jpg)
Laboratory Experiments in Rock Deformation
Deformed marble rock cylinders
![Page 10: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/10.jpg)
Laboratory Experiments in Rock Deformation Stress a rock sample until it fractures (or flows)
![Page 11: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/11.jpg)
In-class exercise, work in groups of 4, turn in write up of answers.
Given these samples, discuss how the magnitude of stresses likely varied relative to one another in these four experiments. Each cylinder was deformed in a different experiment, each with its own axial and radial load (which varied relative to one another).
![Page 12: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/12.jpg)
In-class problem!
1. For maximum and minimum stresses of 600 and 200 mega-pascals (MPa) oriented as a vertical vector and a horizontal, E-W striking vector (respectively), determine the normal and shear stresses on a plane oriented North-South, 45 degrees East. It helps to first draw a block diagram.
2. So max stress is oriented vertically and equal to 600 MPA
3. Min stress is horizontal, oriented east-west and = 200 MPa
![Page 13: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/13.jpg)
In-class problem!
There are two ways to solve these problems.
Use the Mohr Stress Diagram or
Use the equations
(extra credit if you do both…)
![Page 14: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/14.jpg)
![Page 15: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/15.jpg)
Determine the normal and shear stresses on a plane oriented N-S, 45o E
Use the Mohr Stress Diagram!
Maximum stress is oriented vertically and equal to 600 MPA
Minimum stress is horizontal, oriented east-west and = 200 MPa
![Page 16: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/16.jpg)
Use the Equations!
σn = (σ1 + σ3) + (σ1 - σ3) cos 2Θ!2!2!
σs = (σ1 - σ3) sin 2Θ!2!
For the minimum and maximum principle stresses of 600 and 200
megapascals (MPa) oriented as a vertical vector and a horizontal,
E-W striking vector (respectively), determine the normal and shear
stresses on a plane oriented North-South, 45 degrees East
For maximum and minimum stresses of 600 and 200 (MPa) oriented as a vertical vector and a horizontal, E-W striking vector (respectively), determine the normal and shear stresses on a plane oriented North-South, 45 degrees East. It helps to first draw a block diagram.
![Page 17: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/17.jpg)
2 For the stress state in the previous problem, determine the differential stress and mean stress. Start by plotting the solution for normal and shear stresses on the Mohr Stress Diagram.
3 Discuss how a change in differential stress might affect whether a rock might be more or less likely to break. It may help by arbitrarily varying the stresses and looking at how they plot on the circle, or by imagining stress on a cube.
4 Now discuss whether increasing the mean stress would cause a rock to break more readily. Would this be more or less likely with increasing depth in the crust?
5 Draw the stress state where the minimum and maximum stresses are both equal to 600 Mpa.
![Page 18: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/18.jpg)
Following set of slides should be copied and handed out to students for
exercises. Work in groups of 4, so for a class of 80 students, print out 20
sets.
![Page 19: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/19.jpg)
In-class exercise, work in groups of 4 & turn in a write up of your answers.
Problem 1.1 Given these samples, discuss how the mean stress likely varied relative to one another in these four samples. Each cylinder was deformed in a different experiment, each with its own axial and radial load (which varied relative to one another).
![Page 20: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/20.jpg)
![Page 21: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/21.jpg)
In-class problem 1.2
For maximum and minimum stresses of 600 and 200 mega-pascals (MPa) oriented as a vertical vector and a horizontal, E-W striking vector (respectively), determine the normal and shear stresses on a plane oriented North-South, 45 degrees East. It helps to first draw a cross section.
So max stress is oriented vertically and equal to 600 MPA
Min stress is horizontal, oriented east-west and = 200 MPa
![Page 22: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/22.jpg)
Use the Equations!
σn = (σ1 + σ3) + (σ1 - σ3) cos 2Θ!2!2!
σs = (σ1 - σ3) sin 2Θ!2!
For maximum and minimum stresses of 600 and 200 megapascals (MPa) oriented as a vertical vector and a horizontal, E-W striking vector (respectively), determine the normal and shear stresses on a plane oriented North-South, 45 degrees East. It helps to first draw a cross section.
![Page 23: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/23.jpg)
Or use the Mohr Circle!
![Page 24: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/24.jpg)
For the stress state in the previous problem, determine the differential stress and mean stress. Start by plotting the solution for normal and shear stresses for planes of all orientations on the Mohr Stress Diagram.
Discuss how a change in differential stress might make the sample more or less likely to break. It may help by arbitrarily varying the stresses and looking at how they plot on the circle, or by imagining stress on a cube.
Now discuss whether increasing just the mean stress would cause a rock to break more readily (i.e. not deviatoric or differential stress).
Draw the stress state where the minimum and maximum stresses are both equal to 600 MPa. What is the differential stress? Would you expect the rock to deform under these conditions?
![Page 25: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/25.jpg)
In-class problem 2.2
1. For the stress state in the previous problem, determine the differential stress and mean stress. Start by plotting the solution for normal and shear stresses for planes of all orientations on the Mohr Stress Diagram.
![Page 26: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/26.jpg)
In-class problem 2.4
Discuss how a change in differential stress might make the sample more or less likely to break. It may help by arbitrarily varying the stresses and looking at how they plot on the circle, or by imagining stress on a cube.
![Page 27: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/27.jpg)
In-class problem 2.5
1. Now discuss whether increasing the mean stress would cause a rock to break more readily (i.e. not deviatoric or differential stress).
![Page 28: 04Mohr Stress Diagram](https://reader034.fdocuments.us/reader034/viewer/2022051821/5695d3ad1a28ab9b029ec9a1/html5/thumbnails/28.jpg)
In-class problem 2.6
1. Draw the stress state where the minimum and maximum stresses are both equal to 600 Mpa. What is the differential stress? Would you expect the rock to deform under these conditions?