044-05310 ISG Interface Board Installation and Service Manual Rev B

D I S T R I B U T E D A N T E N N A S Y S T E M

INSTALLATION AND SERVICE MANUAL

DASISG INTERFACE BOARD

OCTOBER 2008 REV. B 044-05310

Installation and

© 2008 Powerwave Technologies Incorporated. All rights reserved.

Powerwave Technologies, and the Powerwave logo are registered trademarks.

This Powerwave product is intended only for installation in a RESTRICTED ACCESS LOCATION and is designed to operate within the Normal Operating (typical operating) ranges or conditions specified in this document. Operation of this equipment beyond the specified ranges in this document may cause:

1. Spurious emissions that violate regulatory requirements.

2. The equipment to be automatically removed from service when maximum thresholds are exceeded.

3. The equipment to not perform in accordance with its specifications.

It is the Operator's responsibility to ensure this equipment is properly installed and operated within Powerwave operating specifications to obtain proper performance from the equipment and to comply with regulatory requirements.

For PERMANENTLY CONNECTED EQUIPMENT, a readily accessible disconnect device shall be incorporated in the building installation wiring.

ISG Card

Revision Record

Revision Letter Date of Change Reason for Change

Rev A June 2008 Initial release

Rev B October 2008 Updated the ISG Board Installation in Chapter 3 for AR Installation

044-05310 Rev B i

ISG Card Revision Record

This page intentionally left blank

ii 044-05310 Rev B

044-05310 Rev B iii

Table of ContentsWarning, Cautions, and Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viiSafety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Human Exposure to RF Radiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viiiRepeater Antennas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viiiInstallation and Maintenance of Antenna Systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viiiRadiation Exposure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Electrostatic Discharge (ESD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Chapter 1 - Product DescriptionIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1Scope of Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1System Topology. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

Chapter 2 - Connections and IndicatorsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

Chapter 3 - InstallationIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1Site Survey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1Unpacking and Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1ISG Interface Board Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1ALR Repeater Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2

Installation Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2

ISG Wireline Ethernet Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2ISG Wireless Adapter Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2ISG Wireless + GPS Adapter Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3

Software Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3AR Repeater Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4

Installation Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4


Software Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7OCM Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-8

Installation Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-8Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-8


Software Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13Initial Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13Return For Service Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13

Obtaining An RMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13Repackaging For Shipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13

Chapter 4 -MaintenanceIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1Periodic Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1Replacement Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2

Chapter 5 - SpecificationsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

ISG Interface Board Table of Contents

iv 044-05310 Rev B

List of Figures

Figure 1-1 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

Figure 2-1 ISG Interface Board Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1Figure 2-2 ISG Interface Board Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

Figure 3-1 ISG Interface Board Connections for ALR Repeater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3Figure 3-2 DC Unit Location for AR Repeater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5Figure 3-3 ISG Interface Board Connections for AR Repeater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6Figure 3-4 Cable Inlet Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6Figure 3-5 Ribbon Cable Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7Figure 3-6 GPS Antenna Lead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7Figure 3-7 OCM cover and Connector Mounting Plate screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-10Figure 3-8 ISG Board in OCM (shown without Mezzanine Board attached) . . . . . . . . . . . . . . . . . . . . .3-11Figure 3-9 ISG Wireless and Wireless + GPS Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12

ISG Interface Board List of Tables

List of TablesTable 1-1 Hardware and Software Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2 Table 2-1 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

Table 3-1 ISG Wireline Ethernet–ALR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2Table 3-2 ISG Wireless Adapter Kit–ALR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2Table 3-3 ISG Wireless + GPS Adapter Kit–ALR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3Table 3-4 ISG Wireline Ethernet Installation–AR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4Table 3-5 ISG Wireless Adapter Installation–AR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4Table 3-6 ISG Wireless/GPS Adapter Installation–AR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5Table 3-7 ISG Wireline Ethernet Kit–OCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-8Table 3-8 ISG Wireless Adapter Kit–OCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9Table 3-9 ISG Wireless + GPS Adapter Kit–OCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9Table 3-10 Initial Start-Up Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13

Table 5-1 Component Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

044-05310 Rev B v

Table of Tables ISG Interface Board


vi 044-05310 Rev B

Preface

Warning, Cautions, and NotesWarnings, Cautions, and Notes are found throughout this manual where applicable. The associated icons in warnings and cautions are used to quickly identify a potential condition that could result in the consequences described below if precautions are not taken. Notes clarify and provide additional information to assist the user.

WARNING: The warning symbol means danger. You are in a situation that could cause bodily injury or death. Before you work on any equipment, be aware of the hazards involved with elec-trical and RF circuitry and be familiar with standard practices for preventing accidents.

CAUTION: The caution symbol means the potential exists for equipment damage or loss of data. NOTE: Notes contain helpful suggestions or references to material not covered in the document.

SafetyAny personnel involved in installation, operation, or service of units included in a Powerwave repeater systemmust understand and follow the points below:

❑ Powerwave repeaters are designed to receive and amplify signals from one or more base stations and retransmit the signals to one or more mobile stations. And, also to act the other way round, that is to receive signals from one or more mobile stations, amplify and retransmit the signals to the base stations. Powerwave repeater systems must be used exclusively for this purpose and nothing else.

❑ Units supplied from the mains must be connected to grounded outlets and in conformity with the local prescriptions.

❑ For outdoor use, the power cord should meet at least IP65 encapsulation requirements. Do not turn the main power on until you are ready to commission the equipment.

❑ Power supply units supplied from the mains contain dangerous voltage that can cause electric shock. Disconnect the mains prior to any work in such a unit. Local regulations are to be followed when servicing such units. Only authorized service personnel are allowed to service units while the mains are connected.

❑ When opened, the cover must be secured. Otherwise, the cover can be closed by the wind and cause your fingers getting pinched or your head being hit.

❑ When working on an a repeater on high ground, for instance on a mast or pole, be careful not to drop parts or the entire repeater. Falling parts can cause serious personal injury.

❑ All RF transmitting units, including the ALR Compact Repeater will generate radio signals and thereby give rise to electromagnetic fields that may be hazardous to the health of any person who is extensively exposed close to an antenna.

❑ Beryllium oxide (BeO) may be contained in power devices, for instance in dummy loads in directional couplers (DCC), in combiner units (CMB), and in attenuators on the FON board. Beryllium oxide is poisonous if present as dust or smoke that can be inhaled. Do not file, grind, machine, or treat these parts with acid

❑ Coaxial cables used in many Powerwave systems have the insulation made of PTFE, polytetrafluoro ethylene, that gives off small amounts of hydrogen fluoride when heated. Hydrogen fluoride is poisonous. Do not use heating tools when stripping off coaxial cable insulation. No particular measures are to be taken in case of fire because the emitted concentration of hydrogen fluoride is very low.

044-05310 Rev B vii

Safety ISG Interface Board

Berylliumoxide

hazard

❑ A NiCd battery is mounted in the repeater on the FON PCBA. These batteries contain environmental poisonous substances. If replaced, the old batteries should be disposed of as stated in the local prescriptions.

❑ A lithium battery is permanently mounted in repeater CU units, and in FON and OCM units. Due to the risk of explosion, this battery must only be removed from the board by an Powerwave authorized service technician.

❑ The FON unit contains a Class 1M laser transmitter that emits 2–4 mW invisible laser radiation at 1550 nm during operation and is intended for a restricted location. Avoid direct exposure from a disconnected laser transmitter or fiber cord. For example, do not view directly with optical instruments (magnifiers) and do not view directly with non-attenuating optical instruments.

❑ The FON Unit has this label attached:

❑ Do not power up the FON unit if a fiber cable is not connected to the fiber output UL port, or if a fiber cable is connected to the port but disconnected at the other end.

❑ Never look at the end of a fiber cable. The 1310nm and 1550nm laser light is not visible. Always use an instrument, such as a power meter, to detect signaling.

Warning SignsThe following warning signs must be observed and be kept clean and readable.

Beryllium oxideThis warning sign to the left is applied to boards and units which contain beryllium oxide parts.

This warning sign below is applied at the bottom, inside the cabinet, below the power supply unit.

Human Exposure to RF RadiationSafe distances must be kept when working around antennas. The following paragraphs describe the cautions to be aware of during the installation and maintenance of antenna systems and how to calculate safety distances needed for RF radiation at different antenna power and frequencies.

Repeater AntennasTo be able to receive and transmit signals, a repeater is connected to a donor antenna directed towards the base station and a service antenna directed towards the coverage area. A fiber optic cable from the base station might, however, be substituted for the donor antenna.

Installation and Maintenance of Antenna SystemsInstallation and maintenance of all antenna systems must be performed with respect to the radiation exposure limits for public areas. The antenna radiation level is affected by the output power, antenna gain,

BERYLLIUM OXIDE(Toxic)

used in equipmentsee instruction book

viii 044-05310 Rev B

ISG Interface Board Electrostatic Discharge (ESD)

and transmission devices such as cables, connectors, splitters and feeders. Also have in mind the system minimum coupling loss, typically between 25dB and 35dB, is determined by a standard with the purpose to protect base stations from noise and other performance dropping effects.

Radiation ExposureThe World Health Organization (WHO) and International Commission on Non-Ionising Radiation Protection (ICNIRP) have determined recommendations for radiation exposure. ICNIRP recommends not to exceed the following radiation power for public exposure:

Frequency Radiation power800/900 MHz 4.5W/m²1800/1900 MHz 9.0W/m²2100 MHz 10.0W/m²For antennas larger than 20cm the maximum radiation power can be calculated by using the following formula:

Electrostatic Discharge (ESD) ESD can severly damage essential parts of the equipment if not handled carefully. Parts on Printed Circuit Board Assemblies (PCBA) as well as other parts in the equipment are sensitive to ESD. Never touch the PCBA or uninsulated conductor surfaces unless absolutely necessary.

If you must handle the PCBAs or uninsulated conductor surfaces, use ESD protective equipment or first touch the chassis with your hand. Never let your clothes touch PCBAs or uninsulated conductor surfaces and always store PCBAs in ESD-safe bags.

S= P/(4πr2)S = Radiation power in W/m²P = Output power in Wr = Distance between antenna and human in meters

044-05310 Rev B ix

Electrostatic Discharge (ESD) ISG Interface Board

This page intentionally left blank.

x 044-05310 Rev B

Chapter 1 Product Description

IntroductionThis manual contains installation and maintenance information and procedures for the ISG Interface Board.

Scope of ManualThis manual is intended for use by service technicians familiar with similar types of equipment. It contains service information required for the equipment described and is current as of the printing date. Changes which occur after the printing date may be incorporated by a complete manual revision or alternatively as additions. For details on configuring the software of the ISG Interface, refer to 044-05312 ISG Interface Board Configuration Manual. The manual is organized into chapters as follows:

Product DescriptionThe ISG Interface Board provides a packet data interface between network management systems and repeaters and wideband radio heads. Both IP and SNMP connections are available as well as a GPS interface for automated tuning based on location.

System TopologyFigure 1-1 illustrates packet data on wireless and Ethernet networks connections.

Figure 1-1 System Block Diagram

❑ Chapter 1 - Product Description

❑ Chapter 2 - Connections and Indicators

❑ Chapter 3 - Installation

❑ Chapter 4 - Maintenance

❑ Chapter 5 - Specifications

` `

HTTPS HTTPS

Web Client

TCP / IP NetworkISG Repeater

Netway Manager

Packet Data on Wireless

SNMP over TCP / IP

`

HTTP

Web Craft Terminal

044-05310 Rev B 1-1

Hardware ISG Interface Board

HardwareTable 1-1 lists the hardware and software configurations required for the ISG board to operate:

Table 1-1 Hardware and Software Configurations

Hardware Software

CU K 103/3

SA102 02/4 R1B Software CU CSEL

SA102 07/4 R1A Software CU CSEL, IP

SA102 08/7 P3A5 Software CU CHE K103/3 SLW

SA102 07/7 P3A1 Software CU EDGE CSEL, IP

SA102 07/6 P1A11 Software CU WRH, IP

SA102 02/5 R1C Software CU BSEL

SA102 07/5 R1A Software CU BSEL, IP

SA102 02/2 R2D Software CU CDMA

SA102 07/2 R1A Software CU CDMA, IP

FON K 129 SA102 05/1 R2B Software FON (K129)

BSC K304/TBD or K308/3

SA102 04/1 R1C BSC Software

SA102 06/1 R1B Software BSC-IP

SA102 04/2 R1B BSC Software WCDMA

SA102 06/2 R1A BSC WCDMA IP-Software

1-2 044-05310 Rev B

Chapter 2 Connections and Indicators

IntroductionThis chapter describes the connections and indicators for the ISG Interface Board.

Connections1 Ethernet Connector

2 Battery Connector

3 Ribbon Connector

4 GPS Antenna Connector

5 RF Antenna Connector

6 SIM Card Receptacle

Figure 2-1 ISG Interface Board Connections

3

4

5

6

1

2

044-05310 Rev B 2-1

Indicators ISG Interface Board

Indicators

Figure 2-2 ISG Interface Board Indicators

Table 2-1 LED Indicators

LED Description1 VMOD - indicates ISG board powered on

2 ACT - indicates activity on the connection to the ISG board

3 FAULT - RED LED indicates a fault with the ISG board or the connection

4 3V3 - 3.7 V power indicator for Mezzanine Board

5 5V - 5V power indicator

6 BAT - Green LED indicates battery is powering the ISG board

7 CHG - Yellow LED indicates battery is charging

1

2 3 4 5 6 7

2-2 044-05310 Rev B

Chapter 3 Installation

IntroductionThis chapter contains unpacking, inspection, and instructions for installing and powering up the ISG Interface Board.

Site SurveyPowerwave recommends that a site survey be performed prior to equipment ordering or installation. Performing a detailed site survey reduces or eliminates installation and turn-up delays. Pay particular attention to power plant capacity, cooling needs, floor space, and RF/DC cabling/breaker requirements.

Unpacking and InspectionThis ISG Interface Board has been operated, tested, and calibrated at the factory. Carefully open the container to remove the card. Retain all packing material that can be reassembled in the event the card must be returned to the factory. Perform the following steps:

❑ Visually inspect for damage that may have occurred during shipment in the presence of the delivery person if possible.

❑ Check for evidence of water damage, cracked or broken PC board, loose or missing components, or extraneous packing material in connectors.

❑ Use the packing list to verify all ordered parts are included.

If the ISG Interface Board is damaged, determine the extent of damage and file a claim with the carrier.

If the ISG Interface Board must be returned to factory, please contact the factory for a Return Material Authorization (RMA). See page 3-7 for more information.

ISG Interface Board Kits❑ UA107 62/1 ISG Wireline Ethernet Packet Data (No Wireless Modem)

❑ UA107 62/2 ISG GSM 900/1800 Dual Mode Data with GPRS Wireless Modem

❑ UA107 62/3 ISG CDMA 850/1900 Dual Mode Data with CDMA Wireless Modem

❑ UA107 62/4 ISG GSM 850/1900 Dual Mode Data with GPRS Wireless Modem

044-05310 Rev B 3-1

Installation ISG Interface Board

ALR Repeater InstallationInstallation KitsUse the parts from the appropriate adapter kit to install the ISG Interface Board into the ALR Repeater.

❑ UA107 62/8 ISG Ethernet Adapter Kit

❑ UA107 62/13 ISG Wireless(-20 dB) Adapter Kit

❑ UA107 62/14 ISG Wireless(-10 dB) Adapter Kit

❑ UA107 62/15 ISG Wireless(-10 dB) + GPS Adapter Kit

Installation procedureThe ISG Interface Board is typically mounted in the lower right section of the ALR repeater compartment. Due to different configurations for the ALR Repeater interior compionents, the mounting may vary from application to application. Follow the steps in Tables 3-1 through 3-3. See Figure 3-1 for the location of connectors.

ISG Wireline Ethernet Kit

ISG Wireless Adapter Kit

Table 3-1 ISG Wireline Ethernet–ALR

Step Action

1 Mount the ISG Interface Board in the chassis and secure it with the screws provided in the adapter kit. Be sure to insert all screws before tightening.

2 Disconnect the cable on the connector labelled ANT on DPX2, loosen the nut on the N Connector, and re-move the cable

3 Attach the Ethernet cable 700-24888-150 to the inboard connector on the ISG Interface Board, and extend the RJ-45 end of the cable through the repeater chassis.

4 Attach the ribbon connector to the ISG Interface Board and to the BSC PCBA already mounted in the repeat-er.

Table 3-2 ISG Wireless Adapter Kit–ALR

Step Action

1 Mount the ISG Interface Board in the chassis and secure it with the screws provided in the adapter kit. Be sure to insert all screws before tightening.

2 Disconnect the cable on the connector labelled ANT on DPX2, loosen the nut on the N Connector, and re-move the cable

3 Attach cable VE007 82/1 to the ANT connector on the ISG Interface Board Mezzanine Board DCC, and to the N connector on the repeater chassis.

4 .Attach cable VE001 11/1 to the RF Connector and the DCC on the ISG Mezzanine Board.

5 Attach cable VE007 02/12 to the DPX connector on the ISG Mezzanine Board and to the ANT connector on DPX2.

6 Attach the ribbon connector to the ISG Interface Board and to the BSC PCBA already mounted in the re-peater.

3-2 044-05310 Rev B

ISG Interface Board Installation

ISG Wireless + GPS Adapter Kit

Figure 3-1 ISG Interface Board Connections for ALR Repeater

Software ConfigurationRefer to the ISG Interface Board Configuration Manual (part number 044-05321) to install and configure software.

Table 3-3 ISG Wireless + GPS Adapter Kit–ALR

Step Action

1 Follow steps 1 - 6 in Table 3-2.

2 Attach the RF Cable to the GPS SMA connector on the ISG Interface Board and to the N Connector on the repeater chassis.

3 Attach a cable to the N connector on the repeater chassis to a GPS antenna.

ANT

LO

HI

ANT

LO

HI

P121P128

P111

DPCMS

LNA/ULLNA/DL

PA/ULPA/DL

PSM

DCC/BS

ISG

DPCBS

ANTDPX

P115

RCC

GPS SMA Connector and

RF Connector onISG Mezzanine Board

Ethernet CableConnector

Ribbon Connector

cable for GPSantenna

044-05310 Rev B 3-3


AR Repeater InstallationInstallation KitUse the parts from the appropriate adapter kit to install the ISG Interface Board into the AR Repeater.


❑ UA107 62/11 ISG Wireless Adapter Kit

❑ UA107 62/12 ISG Wireless + GPS Adapter Kit

Installation procedureThe ISG Interface Board is typically installed on top of the Power Supply Unit (PSU). Due to many different configurations for the AR Repeater interior components, the mounting may vary from application to application. Follow the steps in Tables 3-4 through 3-6. See Figure 3-2 for the location of connectors.



Table 3-4 ISG Wireline Ethernet Installation–AR

Step Action

1 Attach the ISG Board battery back-up connector to P101 on the ISG Board.

2 Attach cable 700-2488-150 to the Site LAN connector on the ISG Board and the Site LAN connector on the RJ-45 Connector Adapter.

3 Attach cable 700-2488-150 to the Local LAN connector on the ISG Board and the Local LAN connector on the RJ-45 Connector Adapter.

4 Mount the ISG Interface Board in the chassis plate and secure it with the six screws provided in the adapter kit. Be sure to insert all screws before tightening. Tighten screws to 0.8 - 1.0 Nm (7.0 - 8.8 in-lbs)

5Attach ribbon cable 700-14514-401 to the P130 connector on the ISG Board and the RCI board on the re-peater chassis. Position the cable as shown in Figure 3-3so that the R2R and WLI LEDs are not covered. See Figure 3-5.

6 Attach an Ethernet cable to the inboard connector (Site LAN) on the ISG Interface Board, and to the outboard connector (Site LAN) on the RJ-45 Connector Adapter.

Table 3-5 ISG Wireless Adapter Installation–AR

Step Action

1 Follow steps 1—5 in Table 3-4 above.

2 Install the Cable Inlet as shown in Figure 3-4.

3 Install the Directional Coupler (DC) Unit on the right side of the power supply, and secure it to the repeater chassis with with two M4X14 screws.

4 Attach cable VE007 83/3 to the cable inlet and to the ANT terminal on the DC Unit.

5 Attach cable VE007 10/1 to the P05 connector on the ISG Interface Board Mezzanine Board, and to the MS-20 connector on the DC Unit. Tighten to 7 Nm (61.9 in-lbs)

6 Attach a cable from the DPX terminal on the DC Unit to the ANT terminal on the repeater’s duplexer com-ponent.

7 Attach an antenna cable to the connector on the bottom of the repeater and to a suitable antenna at the site.

3-4 044-05310 Rev B


ISG Wireless + GPS Adapter Kit

Figure 3-2 DC Unit Location for AR Repeater

Table 3-6 ISG Wireless/GPS Adapter Installation–AR

Step Action

1 Follow the steps 1–4 in Table 3-4 and steps 2–5 in Table 3-5.

2 Attach a cable to the GPS SMA connector on the ISG Interface Board and route it through the cable inlet on the repeater chassis. See Figure 3-6

3 Attach the cable a suitable GPS antenna at the site.

DC Unit

M4X14 Screws

Power Supply

044-05310 Rev B 3-5


Figure 3-3 ISG Interface Board Connections for AR Repeater

Figure 3-4 Cable Inlet Location

Battery plug (under cables)

P05 Connector DC UnitMS 20Site LAN

Local LAN

Site LAN

Local LAN

Ribbon Cable

(Not required for wireline ethernetconnection)

Cable to DPX ANT Terminal

3-6 044-05310 Rev B


Figure 3-5 Ribbon Cable Position

Figure 3-6 GPS Antenna Lead


To GPS AntennaGPS Connector

044-05310 Rev B 3-7


3-8 044-05310 Rev B

OCM Installation

Installation KitUse the parts from the appropriate adapter kit to install the ISG Interface Board into the OCM.


Installation procedureThe ISG Interface Board is typically installed beside the Fiber Optic Unit (FOU). Due to many differentconfigurations for the OCM interior components, the mounting may vary from application to application. Followthe steps in Tables 3-7 and 3-8. See Figure 3-8 and 3-9 for the location of connectors.


Table 3-7 ISG Wireline Ethernet Kit for OCM

Step Action

1 Loosen, remove, and retain the two screws on each side of the top cover, as well as the screw at the back of the cover.

2 Lift the cover straight up from the OCM chassis.

3 On the bottom of the OCM, remove the two screws that secure the connector mounting plate to the OCM chassis. See Figure 3-7

4Pull the bottom of the connector mounting plate away from the OCM front panel and slide the plate away from the slot.NOTE: Before disconnecting cables, remove and discard the wire ties from the cable bundle.

5Disconnect the WLI 1 RJ-45 connector from the connector mounting plate by pushing up on the black clip on the front of the connector and pulling the connector away from the plate. Then remove the other end of the cable from the RCC board by pulling it straight up. Set the cable aside.

6Disconnect the Remote RJ-11 connector from the connector mounting plate by pushing up on the black clip on the front of the connector and pulling the connector away from the plate. Then remove the other end of the cable from the RCC board by pulling it straight up. Set the cable aside.

7 Disconnect the ribbon cable from the RCC board.

8 Loosen, remove, and discard the 6 screws that secure the RCC board to the OCM chassis, remove the RCC board from the OCM, and set it aside.

9 Position the ISG Interface Board in place of the RCC Board, then secure it to the OCM chassis with the six screws provided in the adapter kit.

10Attach one of the cables (700-24888-550) to the Site LAN port (labeled SK-2 on the ISG Board) and attach the RJ-45 end of the cable to the connector mounting plate in the middle position. Note that this connector replaces the WLI 1 connector.

11Attach the other 700-24888-550 cable to the Local LAN port (labeled SK-3 on the ISG Board) and attach the RJ-45 end of the cable to the remaining position on the connector mounting plate (in place of the Remote connector).

12 Tilt the front of the connector mounting plate forward, and place it underneath the LED wires, then slip the plate back into the slot on the OCM front panel.

13 On the bottom of the OCM, insert and tighten the two screws that secure the connector mounting plate to the OCM chassis.

14 On the front panel of the OCM, use the “Site LAN” label from the adapter kit to cover the WLI 1 connector label.

15 On the front panel of the OCM, use the “Local LAN” label from the adapter kit to cover the Remote connector label.

16 Attach the ribbon cable from the FON board adjacent to the ISG Board .NOTE: Do not connect the backup battery plug to the receptacle on the ISG Board.


044-05310 Rev B 3-9

NOTE: The Site LAN Connector replaces the WLI1 port on the front of the OCM.


17 Set the power switch on the front of the OCM to the on position.

18 Configure the software for the ISG Interface Board. See the ISG Interface Board Software Configuration manual (044-05321) for details.

19 After configuring the software, connect the backup battery plug to the receptacle on the ISG Board.

20 Reinstall the OCM cover, and tighten the three screws to secure the cover.

Table 3-8 ISG Wireless Adapter Kit for OCM

Step Action

1 Follow steps 1 through 16 in Table 3-7.

2 Connect the antenna wire to the RF Terminal on the ISG Board and to the ANT terminal hole on the OCM front panel.

3 Secure the connector to the panel front with the hardware supplied.

4 Set the power switch on the front of the OCM to the on position.

5 Configure the software for the ISG Interface Board. See the ISG Interface Board Software Configuration manual (044-05321) for details.

6 After configuring the software, connect the backup battery plug to the receptacle on the ISG Board.

7 Reinstall the OCM cover, and tighten the three screws to secure the cover.

Table 3-7 ISG Wireline Ethernet Kit for OCM

Step Action


Figure 3-7 OCM cover and Connector Mounting Plate screws

Cover screws

Connector Mounting Plate screws

3-10 044-05310 Rev B


Figure 3-8 ISG Board in OCM (shown without Mezzanine Board attached)

Cable 700-24888-550 for ISG Local LAN

Cable 700-24888-550 for ISG Site LAN

FON Ribbon Connector

ISG Backup BatteryConnector

Connector Mounting Plate

044-05310 Rev B 3-11


3-12 044-05310 Rev B


Figure 3-9 ISG Wireless Connection

From ISG Board RF Terminal to ANT on front panel

FON Ribbon Connector

ISG Backup BatteryConnector

Cable 700-24888-550 forISG Site LAN



Initial Startup

Return For Service ProceduresWhen returning products to Powerwave, the following procedures will ensure optimum response.

Obtaining An RMAA Return Material Authorization (RMA) number must be obtained prior to returning equipment and to reduce delays in receiving repair service. Please contact our Repair Department at +1 (714) 466-1000 to obtain this number, or FAX your request to +1 (714) 466-5816.

Repackaging For ShipmentTo ensure safe shipment of a component, it is recommended that the original packing materials be reused. If not possible, use suitable shipping cartons and foam inserts to prevent damage in transit.

Table 3-10 Initial Start-Up Procedure

Step Action

1 Turn on the main power.

2 Check the Yellow LED on the power supply unit. It must be on and steady.

3 Refer to Chapter 2 for other indications.

044-05310 Rev B 3-13



1

3-14 044-05310 Rev B

Chapter 4 Maintenance

IntroductionThis chapter contains periodic maintenance and performance test procedures for the ISG Interface Board.

Periodic MaintenancePeriodic maintenance requirements are minimal for the ISG Interface Board. Make sure cables are secure and no dust has built up inside the repeater and on the board.

TroubleshootingThe following paragraphs contain a list of problems that could occur and a few suggested actions that can correct the problem. If the suggested corrective action does not eliminate the problem, please contact your Powerwave field representative or the factory for further instructions.

WARNING: Wear proper eye protection to avoid eye injury when using compressed air.

Table 4-1 Troubleshooting

Problem Suggested Action

Unable to communicate with ISG Board through Web In-terface

Check IP addressVerify password/user nameCheck connector/cable on ISG BoardCheck power to ISG Board

Unable to communicate with ISG Board over wirless con-nection

Check antenna connections to ISG BoardVerify phone numberVerify SIM card seated properly on ISG Board

No power indication Check ribbon connector on ISG Board and PCBA

Unable to find location on GPS

Check GPS connector on ISG Board and repeater chassis

Unable to communicate with repeater or OCM

Check power connection to repeater/OCM

044-05310 Rev B 4-1

Replacement Procedure ISG Interface Board

Replacement ProcedureThe ISG Interface Board can be replaced in the field on site by a qualified technician with experience maintaining RF power amplifiers or similar equipment:

To replace the ISG Interface Board, follow the steps in Table 4-2.

Table 4-2 ISG Interface Board Replacement Procedure

Step Action

1 Turn off power to the repeater or OCM that houses the ISG Interface Board..

2 Starting with the ribbon connector, carefully disconnect all cables and connectors.

3 Remove the screws that attach the ISG Interface Board to the mounting plate and remove the Board from the repeater or OCM. Label all cables and connectiors for easy replace-ment.

4 Replace the ISG Interface Board in reverse order of removal.

4-2 044-05310 Rev B

044-05310 Rev B 5-1

Chapter 5Specifications

IntroductionThis chapter provides specifications about the ISG Interface Board, listed in Table 5-1. .

Table 5-1 Component Specifications

Generic Specifications/Features

Dimensions (W x H x D mm/in) 185 mm (7.30 in) x 35 mm (1.37 in) x 85 mm (3.34 in)

Operating temperature -25 to 85° C ( -77 to 185° F)

Weight .227 kg (.5 lbs)

Power Consumption > 2A @6.5 VDC

Battery Back-up duration 10 minutes

Wireline Communication Interface Ethernet 10/100 BaseTDHCP server with up to 10 IP addressesCircuit switched mode

Wireless Packet Data Support CDMA 850-1900 Dual ModeCDMA-2000 1x, 1x EV-DO, 1x EV-DVGSM 900/1800 Dual Mode

Worldwide Corporate Headquarters1801 East St. Andrew PlaceSanta Ana, CA 92705 USA+1 714 466 1000+1 714 466 5800 FAXwww.powerwave.com

Main European OfficeKnarrarnasgatan 7 8tr.164 40 Kista, Sweden+46 8-540-822-00+46 8-540-824-91 FAX

Main Asia-Pacific Office23 F Tai Yau Building181 Johnston RoadWanchai, Hong Kong+852 2512 6123+852 2575 4860 FAX

Powerwave Technologies, Inc. All rights reserved. Powerwave, Powerwave Technologies, and the Powerwave logo are registered trade-marks of Powerwave Technologies, Inc.

044-05310 ISG Interface Board Installation and Service Manual Rev B

Documents

Transcript of 044-05310 ISG Interface Board Installation and Service Manual Rev B